Haier CRT Television LEC24B3320 Manuel utilisateur

Catégorie
Lecteurs DVD
Taper
Manuel utilisateur

Ce manuel convient également à

LED
LEC24B3320
-1-
Contents
Safety and warnings.......................................................................................2-3
Introduction..................................................................................................4
Stand installation guide................................................................................. 5
Installation................................................................................................... 6-9
Remote Control............................................................................................10
Operation..................................................................................................... 11-13
Trouble Shooting...........................................................................................14
DVD Operation............................................................................................. 15-18
DVD Trouble Shooting...................................................................................19
Warranty.......................................................................................................20
SAFETY AND WARNINGS
To reduce the risk of fire or electric shock, do
not expose this Television to rain or moisture.
WARNING:
-2-
IMPORTANT SAFETY INSTRUCTION
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK).NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN!
CAUTION
CAUTION
The symbol indicates that dangerous voltages
constituting a risk of electric shock are present
within this unit.
The symbol indicates that there are important
operating and maintenance instructions in the
literaturaccompanying this unit.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this Television near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings, install in
accordance with the instructions.
8) Do not install near any heat sources such as radiations,
heat registers, stoves, or other Television (including
amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized plug.
If the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10) Protected the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the Television.
11) Only use attachments/accessories specified by the
manufacturer.
12) Unplug this Television during lighting storms or
when unused for long periods of time.
13) Refer all servicing to qualified service personnel.
Servicing is required when the Television has been
damaged in any way, such as; power-supply cord or plug
is damaged, liquid has been spilled or objects have fallen
into the Television, the Television has been exposed to
rain or moisture, does not operate normally, or has been
dropped.
14) Mains plug is used as the disconnect device, the
disconnect device shall remain readily operable.
15) The ventilation should not be impeded by covering
the ventilation openings with items, such as newspapers,
table-cloth, curtains, etc.
16) No naked flame sources, such as lighted candles,
should be placed on the Television.
17) Attention should be drawn to the environmental
aspects of battery disposal.
18) The use of Television in moderate climate.
19) The Television shall not be exposed to dripping or
splashing and that no objects filled with liquids, such as
vases, shall be placed on the Television.
This symbol indicates that this product incorporates
double insulation between hazardous mains voltage and
user accessible parts. When servicing use only
identical replacement parts.
This marking indicates that this product should not be
disposed with other household wastes throughout the
EU. To prevent possible harm to the environment or
human health from uncontrolled waste disposal,
recycle it responsibly to promote the sustainable
reuse of material resources. To return your used
device, please use the return and collection systems or
contact the retailer where the product was purchased.
They can take this product for environmental safe
recycling.
The batteries shall not be exposed to excessive heat
such as sunshine, fire or the like.
WARNING:
The excessive sound pressure from earphones and
headphones can cause hearing loss.
WARNING:
Haier is committed to safely recycling electronic
products and product materials. Please check for a
local recycling location in the United States at:
1800RECYCLING.COM or call 1.800.RECYCLING.
ENERGY STAR is a joint program of the U.S.
Environmetal Protection Agency and the U.S.
Department of Energy helping us all save
money and protect the environmetal through
energy efficient practices.
This product default mode (standard mode) already
pass the Energy star test. If TV set in other mode, may
increase energy consumption beyond the limits
required for ENERGY STAR qualification.
-3-
High voltages are used in the operation of this television
receiver. Do not the cabinet.
Refer servicing to qualified service personnel.
open
SAFETY AND WARNINGS
To prevent fire or electrical shock hazard, do not expose
the television receiver to rain or moisture.
Do not drop or push objects into the television cabinet
slots or openings. Never spill any kind of liquid on the
television receiver.
Do not block the ventilation holes on the back cover .
Adequate ventilation is essential to prevent failure of
electrical components.
of the TV
Do not trap the power supply cord under the television
receiver s .' stand
Never stand on, lean on, or suddenly push the television or
its stand. You should pay special attention to children.
Serious injury may result if it falls.
Do not place your television on an unstable cart, stand,
shelf or table. Serious injury to an individual and damage
to the television may result if it falls.
/or
When the television receiver is not used for an
extended period of time, it is advisable to disconnect
the AC power cord from the AC outlet.
Avoid exposing the television receiver to direct sunlight
and other sources of heat. Do not stand the television
receiver directly on other products which give off heat,
e.g. video cassette players and audio amplifiers. Do not
place naked flame sources, such as lighted candles on
the television. or near
Dim:51 5*320 mm(不包 括底座)
If the television is to be built into a compartment or similar
enclosure, the minimum distances must be maintained. Heat
build-up can reduce the life of your television, and can also
be dangerous.
-4-
INTRODUCTION
Main features
Accessories
Infrared Remote Control....................
1
Users M anual .................................
1
Battery(AAA)................................... 2
Accessories
Power cable...................................
1
Integrated ATSC TV tuner for HDTV broadcast reception
High brightness provides a vivid and brilliant picture
Deeper blacks and brighter whites with high contrast
Wide Screen aspect ratio (16:9) for a complete home
theater experience
HDMI input for true digital connection
VGA port for connection to PC
Built-in stereo speaker system
Full-function Remote Control
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC.
Main Specifications
x 2
Resolution:
TV System:
Video Signal System:
Receiving Channel:
1366 x 768
16:9
NTSC
Cable :1-135/ Air: 2-69 (ATV&DTV)
x 1
High-Definition Multimedia Interface (HDMI) Input
Audio Input x 2
x 1
Horizontal definition (TV line) Composite Video Input >=350
Component (YPbPr) >=400
Video Input >=400
x 1
AC 100-240V 50/60Hz
2x3W
ATSC Digital system and NTSC Analog system
Headphone Output
x 1
x 1
Coaxial Output
Aspect Ratio:
Viewing Picture Size (diagonal)
Power supply
Audio Output Power (THD 7%):
Component (YPbPr) Input
Composite Video Input
Analog RGB (VGA) Input
Power consumption
x 1
USB Input
24 inches
40W
-5-
Base Stand Assembly Instruction
1. Place the TV with the display side down on a flat surface. Use a cloth to protect . the display
Position the base stand onto the bottom of the stand neck.
2. Attach the base stand to the stand neck firmly tightening the supplied screws.
Note: This stand is not a swivel stand. Do not attempt to rotate the TV.
-6-
INSTALLATION
Front panel
Side panel
REAR Connections
SIDE Connections
All the terminals are (from left to right):
, HDMI2, USB, VGA, PC AUDIO, HEADPHONE, COAXIAL(audio output), RF.
Note: When HDMI has an input signal coming from a DVI source then the audio input signal must be
connected to the PC audio input.
HDMI1
All the terminals are (from left to right):
POWER SOCKET, VIDEO, AUDIO INPUT, .
Note: AV and component (YPbPr) share the R and L audio inputs.
YPbPr INPUT(COMPONENT)
1: Remote control sensor.
2: Indicator LED: BLUE POWER ON.
RED STANDBY.
3:
Side panel keys
1. : Display the input source menu.
2. MENU: Display main MENU.
3. CH+/CH-: In TV mode, press "CH+" or "CH-" to
change the channel up and down. In MENU mode, press
"CH+" or "CH-" to select items; In standby mode, press
"CH+" or "CH-" to turn on the TV.
4. VOL+/VOL-: Adjust sound level. In MENU mode,
press "VOL+ " or "VOL- " to adjust the item that you
selected.
5. STANDBY: Press this button to turn the unit ON
from STANDBY mode. Press it again to turn the set
back to STANDBY.
30 30
YPbPr CC MTS VGA
DTV
STRENGTH
TV AV HDMI
EPGCH LIST FAV
TV
DISPLAY
S.M
P.M
1
3
2
MENU
CH+
CH-
VOL+
VOL-
STANDBY
1
2
3
4
5
ANTENNA
INSTALLATION
Note:
Aerial connections: IEC (female).
Input impendance: 75 unbalanced.
STEPS:
PC
Be sure both the TV and computer are powered off.
1.Connect a VGA and audio cable.
2.Connect the power cord.
3.Turn on the TV, switch to PC mode.
4.Turn on the PC.
-7-
PC
-8-
INSTALLATION
PRESET MODE
1
2
3
4
5
640*480
800*600
1024*768
1280*1024
60
60
60
60
31.47
37.88
48.36
63.98
RESOLUTION
V.Freq.(Hz) H.Freq.(KHz)
1366*768
60
47.71
INSTALLATION
-9-
AV EQUIPMENT
There are two HDMI ports located on the back of your TV. You can connect a Blu-ray player,
DVD player, or other video equipment through these ports.
There is one component (Y, Pb, Pr) and one composite (AV) video input located on the back
of your TV. You can connect a VCR, cable box, or other video equipment to these jacks.
Please see the diagram below. You may also need to refer to the owner's manual of the device
that you are trying to connect.
The television's inputs can be connected to the following types of equipment: VCR, multi disc player,
DVD, camcorder, video game or stereo system, etc.....
YPbPr can support these video formats:480i,576i,480p,576p,720p,1080i, 1080p.
Yellow (video)
White(audio L)
Red(audio R or Pr)
Y
W
R
Blue(Pb)
Green(Y)
B
G
TO AUDIO OUTPUTS
TO VIDEO
OUTP UTS
VIDE O EQUIPMENT
VIDEO EQUIPMENT with YPbPr
-10-
REMOTE CONTROL
VOL
CH
TV
DISPL AY
S.M
P.M
RETURN DISPLAY AUDIO SUBTITLE
REPEAT
GOTO
MENU
SETUP
CH LIST/
ASPECT
EPG/
FAV/
CC/
MTS/
1: POWER
To set the TV standby or on.
2: NUMBER KEY
For direct access to program.
3:
Displays the main on-screen menu.
4: CURSOR
To move within the menu.
5: EXIT
Used to exit menu.
6: VOL+/VOL-
To adjust sound level.
7:
8:
Press to display and select the available video sources.
9: MUTE
To disable or enable the sound.
10: RECALL
To access the previously viewed program.
11: ENTER
Confirms selection.
12: TV DISPLAY
Displays/removes the program Information
13:
14: CH+/CH-
To access the next or previous Program.
15: ASPECT
To change picture aspect .
16: CH LIST /
Used to display the channel list / Eject or Insert the disc.
17: EPG
Display all the information of DTV programs.
18: FAV
Used to access your favorite channels in digital TV mode.
19: CC
Enable or disable the CC function.
20: MTS
Switch the sound stereo.
P.M
Press repeatedly to select a picture mode: Vivid, Standard,
Sports, Movie, or Custom.
S.M
Press repeatedly to switch audio modes: Standard, News,
Music,Theater, Sports or Custom.
9
14
13
10
12
11
15
18
26
24
25
20
1
2
4
5
6
7
19
23
21
22
16
17
30
3 8
29
28
27
For a description of the DVD player function buttons
on the remote, please refer to page 18 of this manual.
-11-
OPERATION
CC Mode CC On
Basic Selection CC1
Advanced Selection Servicel
Option
OK
VGA Setting
H-Pos
V-Pos
Clock
Phase
Auto
50
38
50
17
MENU
1. PICTURE MENU
In this menu, you can adjust the picture options,
such as contrast, brightness, etc.
Press to select, press OK to adjust.
1.1 VGA Setting
When a PC is connected, you can adjust the VGA settings.
1) H-Pos: Adjust the horizontal position of the screen.
2) V-Pos: Adjust the vertical position of the screen.
3) Clock: Fine tune the screen width.
4) Phase: Fine tune the phase of the screen. Usually you
don't adjust this item.
5) Auto: Auto adjust to fit the screen.
Note:
1) If you want to adjust contrast, brightness, color, and
sharpness, the picture mode be set to .will user
2) Cool to give the white colors
a blue tint, Normal to give the white colors a neutral tint, Warm
to give the white colors a red tint.
picture
Adjust the color tempertaure to
Energy Saving mode is the default setting, if you select
some other options, the power consumption may change.
2.AUDIO menu
In this menu, you can ajust the sound options.
Press to select, press to adjust.OK
3.
In this menu, you can adjust the Menu language,
Closed Caption,
Press to select, press to adjust.
SETUP menu
adjust the sleep timer, time zone,
Restore Default, etc.
OK
3.1 Closed Caption
Note:
1)
2)
Audio language is available in ATSC/TVmode only.
Auto volume is available only when the input signal
volume is too large or there is distortion.
1) CC Mode: Switch the closed caption mode.
2) Advanced selection: only available in ATSC.
3) Option: Used to edit the CC font.
Note:
1) Restore Default: Restore Default will clear all the
and reset all the settings to
default values.
saved channels of the
factory
Audio
Setup
TV
Picture
Lock
Picture Mode
Contrast
Brightness
Sharpness
Tint
Color
Color Temperature
Advaced Video
Energy Saving
50
50
50
50
50
Back
Move
ENTER
MENU
OK
Setup
TV
Picture
Lock
Sound Mode
Bass
Treble
Balance
MTS
Digital Output
Surround Sound
Audio
Auto Volume
Only Off
Standard
50
50
50
Stereo
RAW
Off
Off
Audio
Back
Move
ENTER
MENU
OK
TV
Picture
Lock
Menu Language
Closed Caption
Steep Timer
Time Zone
DST
Time Format
Clock
Restor Default
Software Update
English
off
Pacific
off
12-hour
Setup
Audio
Back
Move
ENTER
MENU
OK
-12-
OPERATION
And use the key to lock/unlock
.
OK Parental
Controls
2) MPAA: Switching the movie-rating control level;
N/A, G, PG, PG-13, R, NC-17, X.
Rating
Description
Age
G General audiences, All Ages admitted
PG
Parental Guidance suggested. Some material may not be
Suitable for children.
PG-13
Parents strongly cautioned. Some material .may be
Inappropriate for children under 13.
R
NC-17
X
Restrict. Under 17 requires accompanying parent or adult
guardian(age varies in some jurisdictions)
No one 17 and under admitted.
X is an older rating that is unified with NC-17 but may be
encoded in the data of older movies.
1) Canada English: Switching the English rating control
level: EXEMPT, C, C8+, G, PG, 14+, 18+.
4.LOCK MENU
In this menu, you can change the password and adjust
the vchip settings.
Enter the password, to enter the lock menu. The
factory default password is 0000.
4.1 Change Password
1) old password: Input the old password.
2) new password: Input the new password.
3)Confirm password: Input the new password again.
Enter
Enter
4.2 System Lock
When the System Lock switch is ON, the options
listed below can be adjusted.
4.3 US
Press to display the following screen.OK
1) TV: Press display the following screen.OK
4.4 Canada
Press , to display the following screen.OK
TV
Picture
Lock
Enter Password
System Lock
US
Canada
RRT Setting
Reset RRT
Change Password
Setup
Audio
OK
-----
Back
Move
ENTER
MENU
OK
MPAA
TV
US
MENU
FV
V
S
L
D
ALL
TV RATING
MENU
Canada
Canada Eng
Canada Fre
MENU
-13-
OPERATION
Rating
Description
Age
E Exempt: Includes news, sports, documents and other information
programming: talk shows, music videos, and variety programming.
C Children: Intended for younger children under the age of 8 years.
Pays careful attention to themes that could threaten their sense of
securityand well-being.
C8+ Children over 8 years old: Contains no portrayal of violence as the
preferred, acceptable, or only way to resolve conflict; nor encourage
children to imitate dangerous acts which they may see on the screen .
G General: Considered acceptable for all age groups, Appropriate
viewing for the entire family, contains very little violence, physical,
verbal or emotional.
PG Parental Guidance: Intended for a general audience, but may not be
suitable for younger children (under the age of 8) because it could
contain controversial themes or issues.
14+ Over 14 Years: Could contain themes where violence is one of the
dominant elements of the storyline But it must be integral to the
devel opment of plot or character. Language usage could be profane
and nudity , present within the context of theme.
18+ Adults: Intended for viewers 18 years and older and might contain
depictions of violence, which while related to the development of
plot, character or themes, are intended for adult viewing. Could
contain graphic language and portrayals of secretary and nudity.
2) Canada French: Switching the French-rating control
level: E, G, 8ANS+, 13 ANS+, 16ANS+, 18ANS+.
Rating
Description
Age
E Exempt programming
G General: All ages and children, contains minimal direct violence,
but may be integrated into the plot in a humorous or unrealistic
manner.
8ans+ General but inadvisable for young children :May be viewed by a
wide public audience, but could contain scenes disturbing to
children under 8 who cannot distinguish between imaginary and
real situations. Recommended for viewing with paren.
13ans+ Over 13 years: Could contain scenes of frequent violent scenes
and in tense violence.
16ans+ Over 16 years: Could contain frequent violent scenes and violence.
18ans+ Over 18 years: Only for adult viewing. Could contain frequent
violent scenes and extreme violence.
4.5 RRT setting
ATSC digital TV mode, it can be adjusted
4.6 Reset RRT:
Press
In
to reset the RRT settings to the factory
default values.
OK
5. MENU
In this menu, you can adjust digital and analog TV
Channels.
Press to select, press to adjust.
TV
OK
5.1 Air/Cable:
Select Air TV signal cable TV signal.
5.2 Scan:
If it's the first time you use the TV, you should scan all
the TV channels first.
Press to confirm to display the following
screen.
or
Channel
andOK
5.3 Favorite:
Press to choose/delete favorite channels.
5.4 Show/Hide
Press to display/ hide the current channel.
5.5 DTV signal
Display DTV signal . It can't be selected or
adjusted.
OK
OK
5.6 e-Manual
The use of user guide.
the strength
MENU
Status Scanning
Analog Channels:
Digital Channels:
0
0
5 %...
Air/Cable
Favorite
Show/Hide
DTV Signal
ChannelScan
e-Manual
Cable
Lock
Setup
Audio
TV
Picture
Back
Move
ENTER
MENU
OK
Lock
Setup
Audio
TV
Picture
Air/Cable
Favorite
Show/Hide
DTV Signal
Channel Scan
e-Manual
OK
Cable
Back
Move
ENTER
MENU
OK
MUSIC
Bac k
EXI T
Mov e Sel ect
OK
James Blunt-you are beautiful.mp3
Return
Up Folder
A-Lin-.mp3
.mp3
.mp3
00: 04:22
Pla y
00: 04:22
6. Multimedia
You can display the Music and Photo fil s by using the
USB port that is located on the rear panel:
e
PHOTO MUSIC
Haier Innovation Life
USB 2.0 Bac k
EXI T
Mov e Sele ct
OK
TROUBLE SHOOTING
The LCD TV panel is built with very high precision technology giving you fine picture details
in vibrant color. Occasionally, a few non-active pixels may appear on the screen as a fixed
point of red, green, blue, black or white. Please note this does not affect the performance of
the product.
Component (Y Pb Pr) connections
microwave, electronic equipment,
car/motorcycle, fluorescent light
-14-
Dolby Digital
32
Subtitle choices
8
Audio choices
MP3 files on
CD-R/CD-RW
16:9
LB
TV Aspect
Ratio modes
DVD video
R
RESTRICTED
Parental Lock
This product incorporates copyright
protection technology that is protected
by method claims of certain
U.S.patents and other intellectual
property rights owned by Macro vision
Corporation and other rights owners.
Use of this copyright protection
technology must be authorized by
Macro vision Corporation, and is
intended for home and other limited
viewing uses only. Unless otherwise
authorized by Macro vision Corporation.
Reverse engineering or disassembly is
prohibited.
Manufactured under license from Dolby
Laboratories."Dolby" and the double-D
symbol are trademarks of Dolby
Laboratories. Confidential Unpublished
Works. 1992-1997 Dolby Laboratories, Inc.
All rights reserved.
9
Multi-angle
DVD OPERATION
Caution
This DVD Player has a Class 1 laser which may
be harmful to your eyes. Do not attempt to
disassemble the cabinet or make any adjustments.
Refer all servicing to a qualified professional.
Features
Disc formats supported by this player:
CH LIST/
How to play a DVD disc
1. Change TV input source to "DVD" mode by pressing
button on remote or Source button
on the side of the TV.
2. Place DVD disc in player with the content side
(shiny side) facing the front of the unit.
3. DVD disc will automatically be loaded in to the player
and begin to play.
4. To eject the DVD disc, press Eject/Insert
button on remote or the button on the
side of the unit.
SOURCE
OPEN/CLOSE
PLAY/PAUSE
OPEN/CLOSE
PLAY/PAUSE
Disc with its content side
(shiny side) facing the front
of the unit, insert vertically
into the disc tray
OPEN/CLOSE
PLAY/PAUSE
Disc with its content side
(shiny side) facing the front
of the unit, insert vertically
into the disc tray
DVD SIDE PANEL
DVD SIDE PANEL
-15-
MENU OPERATION
Press the SETUP button on the remote control, the
SETUP MENU will be displayed. After accessing the
setup menu, press to select an item, and press
to select the SUBMENU item. Then press the
ENTER/OK button to confirm. Press to return to
the previous menu. To exit the setup, press the
SETUP button again. In the SETUP MENU, you may
choose adjust any of the following options.
LANGUAGE SETUP
Select Language in the setup menu, and display the
Language submenu:
OSD Language
Use this item to select the language for the
setup menu and screen display.
Subtitle
This option provides the preset subtitle language.
Audio
Select the built-in disc dubbing language options.
DVD Menu
This option provides the film's menu language
options.
VIDEO SETUP
Select Video in the setup menu, and display the
Video submenu:
desired
SYSTEM SETUP
Aspect Ratio
Select the aspect ratio.
Notes:
TV System
Select the TV system.
For more information on output format,
refer to the instructions or your TV set.
RATING SETUP
Select Rating in the setup menu, and display
the Rating submenu:
The image display ratio is related to the recorded disc
format. Somes discs can not display images in the
aspect ratio you choose. If you play a disc recorded in
4:3 format on a wide screen TV, black bars will
appear on the left and right side of the screen. You
must adjust the screen setting depending on the type
of the television you have.
Note: The DVD player setting should be matched to
your TV set.
Parental Control
Set the parental control feature of the player
Note: Th e password is needed to set up the Parental
Control.
Set Password
Input four digits (password), then press ENTER /Ok
to confirm.
Note: If you forget your password, please use the
universal password 6666 to unlock.
MISC SETUP
Select MISC in the setup menu, and display
the submenu:
Use Default Settings
Reset setup data to factory default value.
DVD OPERATION
-16-
MP3/JPEG PLAYBACK
PICTURE CD PLAYBACK
The PICTURE CD disc has such a directory structure
structure as shown in the following picture.
Press Direction key to choose the root
directory and then press ENTER/OK button to
enter into the sub directory. Press Direction
key to choose the desired picture and then
press ENTER/OK or PLAY to enjoy the
picture. If you want to return to the upper menu,
press Direction key to choose the icon and
press ENTER/OK button.
Image rotation
In picture play state, press Direction key to
rotate the picture.
The MP3 disc has a directory structure as shown
picture above.
Press to choose the root directory and then press
ENTER/OK button to enter into the sub directory.
Press to choose the desired track and then press
ENTER/OK or PLAY to enjoy the music or movie. If
you want to return to the previous menu, press
to choose the icon and press the ENTER/OK
button.
Filter: Select the categories of files that are
displayed in the browser list.
Repeat: Change the repeat playing mode
Mode: Select different play modes:
Normal: Play chapters/tracks in normal order.
Shuffle: Play tracks/chapters in a random order until
all tracks/chapters have been played.
Edit Mode: Program tracks/chapters to play. When
you select the mode, press to directory and press
ENTER/OK to choose the desired track. Select Add
to program. Select Program view and select Edit
mode to cancel the edit mode. Press to display the
programmed tracks and press ENTER/OK to start
playback.
Program view: Display the programmed tracks.
Browser view: Display the track directory.
Add to program: Choose the track select Add to
program to add the track to the program play list.
Clear program: In the complete stop state (press the
STOP button twice), select Edit mode to enable the
edit mode. Press to program track and press
ENTER/OK to cancel the desired track. Select Clear
program to delete all tracks in the program play list.
DVD OPERATION
-17-
DVD OPERATION
INSERT/EJECT
Press INSERT/EJECT to insert or eject the
disc.
Note: When inserting the disc, the side with
the label must face the rear of the TV (shiny
side facing you).
SUBTITLE
Press SUBTITLE to choose different
captions(Requires support from disc)
GOTO
For DVD discs, press to choose the desired
title and chapter and search the desired title
time and chapter time. For Super VCD,
VCD, CD discs, press this button to search
the desired disc time and track time and
choose the desired track.
Note: During VCD playback, the PBC mode
must be set to OFF.
0-9 keys
These keys are used to input the time, as well
as title, chapter and track numbers.When a
numeric item is displayed on the screen,
press the 0-9 keys to select the desired entry,
and press ENTER/OK to confirm.
When a VCD is playing(with PBC off), press
the 0-9 keys to select a track directly.
MENU
During DVD playback, press MENU to
display the disc menu of the current title.
During VCD/SVCD playback, press MENU
to control PBC ON/OFF.
SETUP
Press SETUP to enter the system setting
menu. Press the button again to exit the
menu.
RETURN
When a DVD/SVCD/VCD playing, press the
RETURN button to return to the menu(PBC
ON only).
DISPLAY
Press DISPLAY to show the information of
the current playing disc.
ENTER
Press ENTER to confirm your choice on the
screen.
REV
During DVD, CD MP3 or VCD playback,
press REV to scan in reverse.
Press PLAY/PAUSE to resume normal
playback.
FWD
During DVD, CD,MP3, or VCD playback,
press FWD to scan forward. Press
PLAY/PAUSE to resume normal playback.
PREV
During DVD, CD,MP3, or VCD playback,
press PREV to play the previous chapter,
title or track.
NEXT
During DVD,CD,MP3, or VCD playback,
press NEXT toplay the next chapter, title or
track.
STOP
Press the button once and the player will be
in the memory stop state. Press this button
again and the player will be in the complete
stop state.
Play/Pause
Press Play/Pause to play or pause playback.
REPEAT
Press to select between different
repeat modes Repeat Chapter / Repeat
Title / Repeat Offfor DVD discs,
Repeat Single/ Repeat Folder/All/ Repeat
Off (for VCD/CD/MP3 discs)
AUDIO
Changes the audio language or audio
channel.
Function Buttons
-18-
DVD TROUBLE SHOOTING
Ensure you have set the player s AUDIO
settings correctly.
If you have any questions, please consult the troubleshooting guide below:
NO PICTURE OR SOUND
Ensure the power button is on.
Ensure the power outlet is operational.
Ensure the power cord is not damaged.
Ensure the power plug is connected
firmly to the outlet.
PICTURE BUT NO SOUND
Ensure the audio is not set to mute.
POOR PICTURE OR SOUND
Ensure you have set the player s AUDIO
settings correctly
Ensure the disc is not scratched or stained.
BAD DISCDISPLAYED
Ensure the disc is not warped, damaged or
deformed.
Ensure the disc is not badly scratched or
damaged.
Ensure the disc format is compatible with
the player.
Please check whether you have tried to play a
software CD. If so, please restart the player.
REMOTE NOT WORKING
Make sure the Main unit s POWER button is on
Ensure the remote batteries are working.
Point the remote control directly at the player s
IRsensor.
Remove any obstacles between the remote and
theIR sensor.
UNIT NOT WORKING
Turn off the power, and then turn it on
again.
NO DISCDISPLAYED
Ensure you have inserted a disc.
Ensure the disc is inserted properly
(label side facing away from you).
Ensure the disc is not damaged, stained or
scratched.
-19-
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62

Haier CRT Television LEC24B3320 Manuel utilisateur

Catégorie
Lecteurs DVD
Taper
Manuel utilisateur
Ce manuel convient également à