LG WD-12590RD Le manuel du propriétaire

Marque: LG

Modèle: WD-12590RD

Catégorie: Machines à laver

Taper: Le manuel du propriétaire

Washing Machine

OWNER'S MANUAL (2P~35P)

WD-1259(0~9)RD

Thank you for buying a

LG Fully Automatic Washing machine.

Please read your owner's manual carefully, it provides

instructions on safe installation, use and maintenance.

Retain it for future reference.

Record the model and serial numbers of your washing

machine.

Lave-linge

MANUEL D'UTILISATION

(36P~67P)

Nous vous recommandons de lire soigneusement votre

manuel d'utilisation qui vous donnera toutes les instructions

utiles pour l'installation, l'utilisation et la maintenance.

Conservez-le pour vous y référer par la suite.

Enregistrez le modèle et les numéros de série de votre

lave-linge.

roduct Feature

ontents

Warnings ......................................................................................................................3

Specification...................................................................................................................5

Installation......................................................................................................................6

Care before washing....................................................................................................12

Adding detergent..........................................................................................................13

Function ....................................................................................................................15

How to use washer ......................................................................................................16

Maintenance ................................................................................................................26

Troubleshooting guide .................................................................................................30

Terms of Warranty .......................................................................................................34

 Direct Drive System

The advanced Brushless DC motor directly drives the drum without

belt and pulley.

 Water Circulation

Sprays detergent solution and water onto the load over and over.

Clothes are soaked more quickly and thoroughly during wash cycle.

The detergent suds can be removed more easily by the water shower during rinse

cycle. The water circulation system uses both water and detergent more efficiently.

 Tilted Drum and Extra Large Door Opening

Tilted drum and extra large opening make it possible to load

and unload clothing more easily.

 Embossing drum & waved lifter

Embossing drum enhances the washing performance and reduces clothes

damage.The waved lifter spray and help clothes to enhance washing performance

during the washing cycle.

 Automatic Wash Load Detection

Automatically detects the load and optimizes the washing time.

 Built-in Heater

Internal heater helps to maintain water temperature at its optimum level for

selected cycles.

 Child Lock

The Child lock prevents children from pressing any button to change the settings

during operation.

 

arnings

For your safety, the information in this manual must be followed to minimize

the risk of fire or explosion, electric shock, or to prevent property damage,

personal injury, or loss of life.



READ ALL INSTRUCTIONS BEFORE USE

WARNING!

❊ Do not push down the door excessively, when washer door open.

This could topple over the washer.

• Before installation, check exterior damages. If it has,

do not install.

• Do not install or store the washer where it will

be exposed to the weather.

• Do not tamper with controls.

• Do not repair or replace any part of the washer

or attempt any servicing unless specifically

recommended in the user-maintenance instructions

or published user-repair instructions that you

understand and have the skills to carry out.

• Keep the area underneath and around your

appliances free of combustible materials such as

lint, paper, rags, chemicals, etc.

• Close supervision is necessary if this appliance is

used by or near children. Do not allow children to

play on, with, or inside this or any other appliance.

• Keep small animals away from the appliance.

• Do not leave the washer door open.

An open door could entice children to hang on the

door or crawl inside the washer.

• Never reach into washer while it is moving. Wait

until the drum has completely stopped.

• The laundry process can reduce the flame retardant

of fabrics.

• To avoid such a result, carefully follow the garment

manufacturer’s wash and care instructions.

• Do not wash or dry articles that have been cleaned

in, washed in, soaked in, or spotted with

combustible or explosive substances (such as wax,

oil, paint, gasoline, degreasers, dry-cleaning

solvents, kerosene, etc.) which may ignite or

explode. Oil may remain in the tub after a whole

cycle resulting in fire during drying. So, do not load

oiled clothes.

• Do not slam the washer door closed or try to force

the door open when locked. This could result in

damage to the washer.

• When the machine runs high temperature, the front

door may be very hot. Don’t touch it.

• To minimize the possibility of electric shock, unplug

this appliance from the power supply or disconnect

the washer at the household distribution panel by

removing the fuse or switching off the circuit breaker

before attempting any maintenance or cleaning.

• When unplugging power cord, do not pull out by

grasping the cord. Otherwise, the power cord may

be damaged.

• Never attempt to operate this appliance if it is

damaged, malfunctioning, partially disassembled, or

has missing or broken parts, including a damaged

cord or plug.

• Before discarding an old machine unplug it. Render

the plug useless. Cut off the cable directly behind

the appliance to prevent misuse.

• When a product was under water, Please call

service center. The risk of electric shock and fire.

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path

of least resistance for electric current. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug.

The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinance.

• Do not use an adapter or otherwise defeat the grounding plug.

• If you don’t have the proper outlet, consult an electrician.

IMPORTANT SAFETY INSTRUCTIONS

WARNING : To reduce the risk of fire, electric shock, or injury to persons when using

the washer, follow basic precautions, including the following:

SAVE THESE INSTRUCTIONS

WARNING :

Improper connection of the equipment-grounding conductor can result in risk of electric shock. Check with

a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded. Do not modify

the plug provided with the appliance - if it does not fit the outlet, have a proper outlet installed by a qualified electrician.

arnings

To minimize the risk of fire in a tumble dryer, the following should be observed:

• Items that have been spotted or soaked with vegetable or cooking oil constitute a fire

hazard and should not be placed in a tumble dryer.

Oil-affected items can ignite spontaneously, especially when exposed to heat

sources Such as in a tumble dryer. The items become warm, causing an oxidation

reaction in the oil. Oxidation creates heat. If the heat cannot escape, the items can

become hot enough to catch fire. Piling, stacking or storing oil-affected items can

prevent heat from escaping and so create a fire hazard.

If it is unavoidable that fabrics that contain vegetable or cooking oil or have been

contaminated by hair care products be placed in a tumble dryer they should first be

washed in hot water with extra detergent-this will reduce, but not eliminate, the

hazard. Washed in hot water with extra detergent-this will reduce, but not

eliminate, the hazard. The ‘cool down’ cycle of tumble dryers should be used to

reduce the temperature of the items. They should not be removed from the tumble

dryer or piled or stacked while hot.

• Items that have been previously cleaned in, washed in, soaked in or spotted with

petrol/gasoline, dry-cleaning solvents or other flammable or explosive substances

should not be placed in a tumble dryer.

Highly flammable substances commonly used in domestic environments include

acetone, denatured alcohol, petrol/gasoline, kerosene, spot removers (some

brands), turpentine, waxes and was removers.

• Items containing foam rubber (also known as latex foam) or similarly testured rubber.

like materials should not be dried in a tumble dryer on a heat setting.

Foam rubber materials can, when heated, produce fire by spontaneous combustion.

• Fabric softeners or similar products should not be used in a tumble dryer to eliminate

the effects of static electricity unless this practice is specifically recommended by the

manufacturer of the fabric softener or product.

• Undergarments that contain metal reinforcements should not be placed in a tumble

dryer.

Damage to the tumble dryer can result if metal reinforcements come loose during

drying. When available a drying rack could be used for such items.

• Plastic articles such as shower caps or babies waterproof napkin covers should not

be placed in a tumble dryer.

• Rubber-backed articles, clothes fitted with foam rubber pads, pillows, galoshes and

rubber-coated tennis shoes should not be placed in a tumble dryer.

pecification

 Name : Front loading washing machine

 Power supply : 220-240 V~, 50 Hz

 Size : 635 mm(W) x 740 mm(D) x 925 mm(H)

 Weight : 80 kg

 Wash capacity (Max. Watt) : 12 kg (2200 W)

 Dry capacity (Max. Watt) : 7 kg (2200 W)

 Spin speed : No Spin/400/800/1000/1200

 Water consumption : 96



 Permissible water pressure : 0.3~10 kgf/cm

(30~1000 kPa)

❋ The appearance and specifications may be varied without notice to improve the units quality.

❋ Specifications subject to change by manufacturer.



Accessories

Drum

Drain Plug

Drain Pump Filter

Lower cover cap

Door

Adjustable Feet

Drain Hose

Control Panel

Shipping Bolts

Power Plug

• If the supply cord is damaged,

it must be replaced by the

manufacturer or its authorized

service technician in order to

avoid a hazard.

Dispenser

Inlet hose Spanner

nstallation

1. To prevent internal damage during

transport, the special 4 bolts are locked.

Before operating the washer, remove

the bolts along with the rubber bungs.

• If they are not removed, it may cause

heavy vibration, noise and malfunction.

3. Take out the 4 bolts along with the

rubber bungs by slightly twisting the

bung. Keep the 4 bolts and the spanner

for future use.

• Whenever the appliance is transported,

the transit bolts must be refitted.

The appliance is fitted with transit bolts to prevent internal damage during transport.

• Packing and all transit bolts must be

removed before using the washer.

󳀙 When unpacking the base, be sure to

remove the additional packing support

in the middle of the base packing.

2. Unscrew the 4 bolts with

the spanner supplied.

4. Close the holes with the caps supplied.



Transit bolts

Install or store where it will not be exposed to temperatures below freezing or exposed to the

weather.

Properly ground washer to conform with all governing codes and ordinances.

The base opening must not be obstructed by carpeting when the washing machine is installed on

a carpeted floor.

In countries where there are areas which may be subject to infestation by cockroaches or other

vermin, pay particular attention to keeping the appliance and its surroundings in clean

condition at all times.

Any damage which may be cause by cockroaches or other vermin will not be covered by the

appliance guarantee.



Removing transit bolts

Washer

Base Packing

Packing Support

nstallation

Level floor :

Allowable slope under entire washer is 1°

Power outlet :

Must be within 1.5 meters of either side of location of

washer. Do not overload the outlet with more than one

appliance.

Additional Clearance :

For wall, door and floor modeling is required.

(10cm : rear / 2cm : right & left side)

Do not place or store laundry products on top of

washer at any times.

They can damage the finish or controls.



Installation place requirement



Positioning

Install the washer on a flat hard floor.

Make sure that air circulation around the washer is not impeded by carpets,rug etc.

• Before placing the washer on tiles, apply a rubber mat under the feet.

• Never try to correct any unevenness in the floor with pieces of wood, cardboard or similar

materials under the washer.

• If it is impossible to avoid positioning the washer next to a gas cooker or coal burning stove,an

insulating(74x92.5cm) covered with aluminum foil on the side facing the cooker or stove,must be

inserted between the two appliance.

• The washer must not be installed in rooms where the temperature can drop below 0°C.

• Please ensure that when the washer is installed, it is easily accessible for the engineer in the

event of a breakdown.

• With the washer installed adjust all four feet using the transit bolt spanner provided ensuring the

appliance is stable, and a clearance of approximately 20mm is left between the top of the washer

and the underside of the work-top.

• The installation instructions shall state that the openings must not be obstructed by a carpet if it

has ventilation openings in the base.

Washer

Drain Hose

Laundry

Tub

approx.

2cm

nstallation



Water supply pressure must be between 30kPa and 1000kPa

(0.3~10kgf/cm

)



Don’t strip or crossthread when connecting Inlet hose to the valve.



If the water supply pressure is more than 800kPa, a decompression device

should be installed.

• Two rubber seals are supplied with the water inlet hoses these are

in order to prevent water leaks.

• Check water tightness of washing machine connections by turning

the tap completely on.

• Periodically check the condition of the hose and replace the hose if

necessary.

• Make sure that there is no kink on the hose and that it is not

crushed.



Washing Machine is to be connected to the water mains using new hose-sets and that old

hose-sets should not be used.



Connecting water supply hose

1. Do not use an extension cord or double adapter.

2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agents or similarly

qualified person in order to avoid a hazard.

3. Always unplug the machine and turn off the water supply after use.

4. Connect the machine to an earthed socket in accordance with current wiring regulations.

5. The appliance must be positioned so that the plug is easily accessible.

• Repairs to the washing machine must only be carried out qualified personnel. Repairs carried out by inexperienced

persons may cause injury or serious malfunctioning. Contact your local service center

• Do not install your washing machine in rooms where temperatures below freezing may occur. Frozen hoses may burst

under pressure. The reliability of the electronic control unit may be impaired at temperatures below freezing point.

• If the appliance is delivered in the winter months and temperatures are below freezing : Store the washing machine

at room temperature for a few hours before putting it into operation.



Electrical connection

CAUTION concerning the Power Cord

Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which

powers only that appliance and has no additional outlets or branch circuits. Check the specification page of

this owner's manual to be certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged

wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous.

Any of these conditions could result in electric shock or fire. Periodically examine the cord of your

appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the

appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect

the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a

door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the

appliance. If this appliance is supplied from a cord extension set or electrical portable outlet device, the

cord extension set or electrical portable outlet device must be positioned so that it is not subject to

splashing or ingress of moisture.

CAUTION

This appliance is not intended for use by young children or infirm persons without supervision.

Young Children should be supervised to ensure that they do not play with appliance.

CAUTION

Hose connector

Sealingwasher

Cold

water tap

NOTE

After completing connection, if water leaks from the hose, repeat the same steps. Use the most conventional type of

faucet for water supply. In case the faucet is square or too big, remove the spacing ring before inserting the faucet into

the adaptor.

nstallation



Normal Tap without thread & screw type inlet hose



Normal Tap without thread & one touch type inlet hose

1. Unscrew the fixing screw to

attach the tap.

2. Push the connector up till the

rubber packing is in tight contact

with the tap. Then tighten the 4

screws.

3. Push the water supply hose

vertically upwards so that the

rubber packing within in the hose

can adhere completely to the tap

and then tighten it by screwing it

to the right.

1. Un tighten the upper connector

screw.

2. Push the upper connector up till

the rubber packing is in tight

contact with the tap. Then tighten

the 4 screws.

3. Connect the water supply hose to

the middle connector, pushing

the plate down.

• Your machine comes with only

cold water connection.

• Make sure that there are no

kinks in the hose and that it is

not crushed.

• Make sure that the rubber

seal is inside the hose

connector.

• In case the diameter of the

tap is large remove the guide

plate.

• Turn the middle connector not

to have water leaked.

• To separate the water supply

hose from the middle connector

shut off the tap. Then pull the

inlet hose down, pushing the

plate down.

Upper

Connector

Upper

Connector

Upper Connector

Plate

Water supply hose

Fixing screw

Rubber

packing

Rubber

packing

Middle

connector

Middle connector

Hose

connector

Guide plate

Connector

Used the horizontal tap

Horizontal tap

Extension tap

Square tap

Rubber

seal

Rubber packing

nstallation



Installation of drain hose

• The drain hose should not be placed higher

than 100 cm above the floor. Water in the

washer does not drain or drains slowly.

• Proper securing of the drain hose will

protect the floor from damage due to water

leakage.

• When the drain hose is too long, do not

force back into the washer. This will cause

abnormal noise, malfunction, and water

leakage.

• When installing the drain hose to a sink,

secure it tightly with a string.

• Proper securing of the drain hose will

protect the floor from damage due to water

leakage should the drain hose become

loose.

This equipment is not designed for maritime use or for use mobile installations such as

caravans, aircraft etc.

Turn off the stopcock if the machine is to be left for any length of time (e.g. holiday),

especially if there is no floor drain(gully) in the immediate vicinity.

When disposing of the appliance, cut off the mains cable, and destroy the Plug.

Disable the door lock to prevent young children being trapped inside.

Packaging material (e.g. Films, Styrofoam) can be dangerous for children. There is a risk of

suffocation ! Keep all packaging well away from children

about 100 cm

Laundry tub

Hose

Retainer

Tie

strap

max. 100cm

min. 60cm

max. 100cm

min. 60cm

about 105 cm

max. 100 cm

min. 60 cm

about 145 cm

nstallation

 Concrete floors

 Wooden floors (Suspended floors)

• The installation surface must be clean, dry and level.

• Install washer on a flat hard floor.

 Tile floors (Slippery floors)

• Position each foot on the Tread Mate and level the machine to suit. (Cut Tread Mate into

70x70 mm sections and stick the pieces on to the dry tile where machine is to be placed.)



Tread Mate is a self adhesive material used on ladders & steps that prevents slipping.

• Wooden floors are particularly susceptible to vibration.

• To prevent vibration we recommend you place rubber cups under each

foot, at least 15mm thick under the washer, secured to at least 2 floor

beams with screws.

• If possible install the washer in one of the corners of the room, where the floor is more stable.



Insert the rubber cups to reduce vibration.



Rubber cups ( p/no. 4620ER4002A) can be purchased from the LG spare parts department.

Important!

• Proper placement and levelling of the washer ensures long, regular and reliable operation.

• The washer must be absolutely horizontal and stand firmly in position.

• It must not “Seesaw” across corners under load.

• The installation surface must be clean, free from floor wax and other lubricant coatings.

• Do not let the feet of the washer get wet. If feet of the washer get wet, slipping may occur.



It can be purchased from

hardware suppliers.



Level adjustment

1. Adjusting the washing machine level properly prevents excessive

noise and vibration.

Install the appliance on a solid and level floor surface, preferably in

a corner of the room.

2. If the floor is uneven, adjust the adjustable feet as required. (do

not insert pieces of wood etc. under the feet)

Make sure that all four feet are stable and resting on the floor and

then check that the appliance is perfectly level. (use a spirit level)



After the washer is level, tighten the lock nuts up towards of the base of

the washer. All lock nuts must be tightened.

❊ Diagonal Check

When pushing down the edges of the washing machine top plate diagonally, the

machine should not move up and down at all. (Please, check both of two directions)

If machine rocks when pushing the machine top plate diagonally, adjust the feet again.

NOTE

Timber or suspended type flooring may contribute to

excessive vibration and unblance errors.

NOTE

In the case that the washing machine is installed on a raised

platform, it must be securely fastened in order

to eliminate the risk that it might fall off.

Lock nut

Adjustable feet

Rubber Cup

Adjustable feet Adjustable feet

Higher

Lower

are before washing

1. Care Labels

Look for a care label on your clothes. This will tell you about the fabric content of your garment and

how it should be washed.

2. Sorting

To get the best results, Sort clothes into loads that can be washed with the same wash cycle.

Water temperature and spin speed and different fabrics need to be washed in different ways.

Always sort dark colors from pale colors and whites. Wash separately as dye and lint transfer can

occur causing discoloration of white etc. If possible, do not wash heavily soiled items with lightly

soiled one.

Soil (Heavy, Normal, Light) Separate clothes according to amount of soil.

Color (White, Lights, Darks) Separate white fabrics from colored fabrics.

Lint (Lint producers, Collectors) Wash lint producers and lint collectors

separately.

3. Caring before loading



Caring before washing



Before the first washing

 Combine large and small items in a load. Load large items first. Large items should not be more

than half the total wash load.

Do not wash single items. This may cause an out-of-balance load. Add one or two similar items.

Select a cycle (COTTON 60°C, add a half load of detergent) allow the unit to wash without clothing.

This will remove residues from the drum that may have been left during manufacturing.

• Check all pockets to make sure that they are

empty. Items such as nails, hair clip,

matches, pens, coins and keys can damage

both your washer and your clothes.

• Pre treat dirt and stains by brushing a little

detergent dissolved in water onto stains like

collars and cuffs to help shift dirt.

• Close zippers, hooks and strings to make

sure that these items don’t snag on other

clothes.

• Check the folds of the flexible gasket (gray)

and remove any small articles,if any.

• Check inside of the drum and remove any left

items in it for next wash cycle.

• Remove any clothing or items on the flexible

gasket to prevent clothing and the gasket

damages.

dding detergent

• Main wash only

➔

• Pre Wash + Main Wash

➔

• Do not exceed the maximum fill line.

Close the dispenser drawer slowly.

Overfilling can cause early dispensing

of the fabric softener which could stain

clothes.

• Do not leave the fabric softener in the

detergent drawer for more than 2 days.

(Fabric softener could harden)

• Softener will automatically be added

during the last rinse cycle.

• Do not open the drawer when water is

supplied.

• Solvents(benzene, etc) are not

allowable.

1. The Dispenser Drawer

2. Adding Fabric Softener



Adding detergent and fabric softener

Do not pour fabric softener

directly on the cloths

NOTE

Detergent for

main wash

Fabric

softener

Detergent for

pre wash

dding detergent

• The detergent should be used according to the

instruction of the detergent manufacture.

• If too much detergent is used, too many suds

can occur and this will decrease the washing

result or cause heavy load to the motor.

• Use powder detergent only for the front

loading washer.

❇

If suds occur too much, pleas reduce the

detergent amount.

• Detergent usage may need to be adjusted

for water temperature, water hardness,

size and soil level of the load. For best

results, avoid oversudsing.

4. Water softener

• A water softener, such as Anti limescale

(Clagon) can be used to cut down on the

use of detergent in extremely hard water

areas. Dispense according to the amount

specified on the packaging.

First add detergent and then the water

softener.

• Use the quantity of detergent as for soft

water.

❋

Tips

Full load : according to manufacturer’s

recommendation.

Part load : 3/4 of the normal amount.

Minimum load : 1/2 of full load.

• Detergent is flushed from the dispenser at

the beginning of the cycle.

3. Detergent dosage

1) Open the door and Tablets into the drum.

5. Using the Tablets

2) Load the laundry into the drum.

3) Close the door.

unction



Recommended courses according to the laundry type

❋ Water Temperature: Select the water temperature to the wash cycles. Always follow garment manufacture’s care label or

instructions when laundering.

❋ Intensive: When washing full load or heavily soiled laundry, you can increase effectiveness by choosing intensive option.

❋ Pre Wash: If the laundry is heavily soiled, “Pre Wash” option is recommended. Pre Wash is available in Cotton, Cotton

Quick, Synthetic and Baby Care, Wash+Dry(7kg/7kg) Program.

Cotton

Color fast garments (shirts, night

dresses, pajamas...) and lightly soiled

white cotton (underwear...)

- Pre Wash

- Rinse+Spin

- Dry Only

- Bio

- Soak

- Intensive

- Water Plus

- Time Delay

- Pre Wash

- Rinse+Spin

- Bio

- Soak

- Intensive

- Water Plus

- Time Delay

60˚C

(Cold, 30˚C,

40˚C, 95˚C)

Cotton

Quick

Cotton Which is lightly soiled.

40˚C

(Cold, 30˚C,

60˚C, 95˚C)

Synthetic

Polyamide, Acrylic, Polyester.

40˚C

(Cold, 30˚C,

60˚C)

Rating

Less than

6.0kg

- Rinse+Spin

- Intensive

- Time Delay

Delicate

Delicate laundry easily damaged.

40˚C

(Cold, 30˚C)

Less than 3.0kg

Hand Wash

/Wool

“Hand Wash” marked laundry

or machine washable woolens.

Maximum

load

10.0kg

Less than

6.0kg

Less than

7.0kg

Less than

5.0kg

- Rinse+Spin

- Intensive

- Water Plus

- Time Delay

- Rinse+Spin

- Dry Only

- Intensive

- Water Plus

- Time Delay

- Pre Wash

- Rinse+Spin

- Bio

- Soak

- Intensive

- Water Plus

- Time Delay

- Pre Wash

- Rinse+Spin

- Dry Only

- Bio

- Soak

- Intensive

- Water Plus

- Time Delay

Quick 30

Colored Landry which is lightly soiled fast.

30˚C

(Cold, 40˚C)

30˚C

(Cold)

Duvet

Cotton bedding with filling, duvet, pillow,

blanket, sofa cover with light filling.

Wash+Dry

(7kg/7kg)

A small amount of laundry which can be

dried.

60˚C

(Cold, 30˚C,

40˚C, 95˚C)

Baby Care

Lightly soiled baby wear

95˚C

(40˚C, 60˚C)

Maximum

Load

Additional

Option

Proper Temp.

(Option)

Fabric Type

Program

❋ Notes : Neutral detergent is recommended.

The wool cycle features gentle tumbling and low-speed spin for garment care.

The wool wash cycle of this machine has been approved by Woolmark for the washing of machine

washable Woolmark products provided that the products are washed according to the instructions

on the garment label and those issued by the manufacturer of this washing machine M0806.

ow to use washer

• Press the Power( ) button to start.

• Press the Start/Pause( ) button.

• Initial condition

- Wash : Only main wash.

- Rinse : Normal

- Water temperature : 60°C

- Spin : 1200 rpm

- Program : Cotton

• Press the Power( ) button to turn the

washer on.

• Select the desired cycle with the program

dial and if required, make any changes to

the washing conditions by pressing the

buttons accordingly.

For selecting the each conditions, please refer

to the page17~page25

• Press the Start/Pause button to

commence the cycle.

1. Cotton automatically

selected upon power on.

2. Manual Selecting

ow to use washer

ProgramPower

• Press the Power( ) button to turn power

on and off.

• To cancel the Time Delay function, the

Power( ) button must be pressed.

• When the Power( ) button is pressed, the

washer is ready for Cotton program. And the

other initial conditions as follows.

• So, if you want to advance into the washing

cycle without changing the program, just

press Start/Pause( ) button and then the

washer will proceed.

■

Initial program

- Cotton Program / Main Wash / Rinse:Normal /

60°C/ 1200rpm

(1)Button: Power

(2)Dial: Program

(3)Button: Start/Pause

(4)Button: Option

(5)Child lock

(6)Button: Rinse

(7)Button: Spin

(8)Button: Intensive

(9)Button: Water Plus

(10)Button: Time Delay

(11)Button: Temperature

(12)Button: Tub Clean

(13)Dial: Dry

• 9 programs are available according to the

laundry type.

• Dial lamp will light up to indicate selected

program.

• When Start/Pause( ) button is pressed,

the Cotton program is automatically

selected.

- By turning the Program dial, the program is

Selected in order of “Cotton – Cotton Quick

– Synthetic – Delicate – Hand Wash/Wool –

Duvet – Quick 30 – Wash+Dry(7kg/7kg) –

Baby Care”.

For information regarding laundry type for

each program, please refer to page 15.

1. Power

2. Initial Program

(1) (3) (4) (6) (7) (11) (12)(8,9,10) (13)(5)(2)

ow to use washer

Option

• By pressing the option

button, only one option

function may be selected.

Start/Pause

• This Start/Pause button is used to start

wash cycle or pause the wash cycle.

• If temporary stop of wash cycle is needed,

press “Start/Pause” button.

• When in Pause, the power is turned off

automatically after 4 minutes.

NB. The door will not open before 1 to 2

minutes when Pause is selected, or at

the end of the wash cycle.

1. Start

• Use this option for loads that need

pretreatment. This adds 16 minutes of pre

washing before draining.

- When using Pre Wash option, do not use a

liquid detergent for the main wash.

Use powder for the main wash.

1. Pre Wash

• Use this option to rinse and then spin

2. Rinse + Spin

• When you want dry only, select the this

option. Available in Cotton, Cotton Quick,

Quick 30 and Baby Care.

3. Dry Only

• If you want to eliminate protein stains(milk,

blood, chocolate...), you may select Bio

function by pressing the option button.

NB. You can select Eco function when

temperature is higher than 60˚C in

Cotton, Cotton Quick, Synthetic,

Wash+Dry(7kg/7kg), Baby Care.

4. Bio

• Use this mode to wash normal clothes or

thick and heavy clothes which are

excessively dirty.

The matching indicator lamp will light up for

identification.

5. Soak

2. Pause

ow to use washer

Rinse

• By pressing the Rinse

button, the Rinse type can

be selected.

• Baby Care performs 4 Rinses

• Cotton (for full load), Synthetic, Duvet,

Hand Wash/Wool, Wash+Dry(7kg/7kg) performs

3 Rinses

• Cotton Quick, Quick 30, Delicate performs 2

Rinses.

• Used to additional rinse, which may assist in

removing traces of detergent residue.

• By selecting Rinse

or Medic Rinse

function, the Rinse Time and the Rinse

water are increased.

• Medic Rinse heats the water to 40 Deg in

the last rinse.

• Is selected by pressing the Rinse button

repeatedly this function leaves clothes in the

washer; suspended in the water after a rinse

without entering into spin.

• To proceed to a Drain or Spin function after

a Rinse hold, select Drain on the program

dial or press the Spin button for the desired

speed, then press the Start/Pause button.

The matching indicator lamp will light up for

identification.

Child lock

If you choose to lock the buttons on the

control assembly to prevent tampering, this

function may be selected.

• Child lock can be set by pressing and

holding the Option and Rinse button

simultaneously. (About three seconds)

• When child lock is set, all buttons are

inoperable.

• To deactivate Child lock system, press and

hold the Option and Rinse button

simultaneously again.

(About three seconds)

• To change to the desired program, whilst in

child lock mode.

1. Press and hold both Option and Rinse

button to cancel the child lock.

(About three seconds)

2. Press the Start/Pause button.

3. Select the desired program and press the

Start/Pause button again.

• The child lock can be set at any time and it

is automatically canceled when operational

errors occur.

1. Normal

2. Rinse

& Medic Rinse

3. Rinse Hold

Change

the desired

program

ow to use washer

Spin

• Spin speed is available according to the

program as follows.

- Wash+Dry(7kg/7kg)

1000 – 1200

- Cotton & Cotton Quick & Quick 30

No Spin – 400 – 800 – 1000 – 1200

- Baby Care & Synthetic

No Spin – 400 – 800 – 1000

- Delicate & Duvet

No Spin – 400 – 800

- Hand Wash/Wool

No Spin – 400

• By pressing the Spin button,

the spin speed can be

chosen.

• If “No Spin” is selected, the washer stops

after draining the water from the last spin.

The matching indicator lamp will light up for

identification.

Water Temperature

• By pressing the Temp.

button, the water

temperature can be

selected.

- Cold

- 30˚C / 40˚C / 60˚C / 95˚C

• Water temperature can be selected as

below according to the program.

- Baby Care

40˚C - 60˚C - 95˚C

- Cotton & Cotton Quick &

Wash+Dry(7kg/7kg)

Cold - 30˚C - 40˚C - 60˚C - 95˚C

- Synthetic

Cold - 30˚C - 40˚C - 60˚C

- Delicate & Quick 30 & Hand Wash/Wool

Cold - 30˚C - 40˚C

- Duvet

Cold - 30˚C

The required temperature lamp will light up for

identification.

For the more detailed information, please refer

to the page15.

1. Spin selection

2. No spin

La page charge ...

LG WD-12590RD Le manuel du propriétaire

Marque: LG

Modèle: WD-12590RD

Catégorie: Machines à laver

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: LG WD-12590RD Owner's manual

LG WD-12590RD Le manuel du propriétaire

LG WD-12590RD Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents