Driver Assembly Manual
®
2
WARNING!
• Refer servicing to a qualified technician.
• To prevent fire or shock hazard, do not
expose this module to moisture.
• Turn the amplifier off should any abnormal
conditions occur.
• Do not drive speaker beyond its rated power.
Content Check List............................ 3
Connection................................. 4
Protect Your Investment........................ 4
Break-In................................... 4
Speaker Placement ........................... 4
Achieving Superior Imaging . . . . . . . . . . . . . . . . . . . .4
Balancing Hard vs. Soft Surfaces Improves
High- and Mid-Frequency Performance ............4
Painting the Speaker Grille ..................... 5
Pre-Installation Checklist ....................... 6
Part Identification ............................ 7
Installation ..............................8 - 14
Driver Assembly Installation Preparation ...........8
Attach Trim Pieces ...........................9
Mounting The Driver Assembly .................10
Securing The Driver Assembly..................11
Attach The Front Baffle Trim ...................12
(Optional) Apply The Logo Badge...............13
(Optional) Apply The Speaker Grille . . . . . . . . . . . . .14
Dimension Drawing. ......................... 15
Specifications .............................. 16
Per the European Union WEEE (Waste Electrical and
Electronic Equipment) directive effective August 13,
2005, we would like to notify you that this product
may contain regulated materials which upon disposal,
according to the WEEE directive, requires special reuse
and recycling processing. For this reason, Martin Logan
has arranged with our distributors in European Union
member nations to collect and recycle this product at
no cost to you.
To find your local distributor, please contact the dealer
from whom you purchased this product, email
[email protected] or visit the distributor locator at
www.martinlogan.com.
Please note, only this product itself falls under the
WEEE directive. When disposing of the packaging and
other related shipping materials, we encourage you to
recycle these items through the usual channels.
The lightning bolt flash with arrowhead symbol
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to
constitute a risk of electric shock.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and maintenance
(servicing) instructions in the literature
accompanying the appliance.
The fire within an equilateral triangle is intended
to alert the user to the potential of creating a fire
hazard if they do not follow the instructions.
The dollar sign within an equilateral triangle is
intended to alert the user that they run the risk
of causing damage that could be potentially
expensive to repair if they don’t follow the
instructions.
3
Content Check List
A complete Statement 40XW is shipped in 3 boxes. This manual refers to box 3 of 3 which is the Driver Assembly. The
Statement 40XW Driver Assembly contains the following items.
Should you require assistance, please call our service department at (785) 749-0133.
40XW Driver Assembly • Front Baffle Trim • Speaker Grille Cover • Extra Grille Scrim • Trim Pieces • Machine Screws
4x Brass Screws • MartinLogan Logo Badge and Template
4
The amplifier is connected to the Statement 40XW through the
binding posts located on the top or bottom of the in wall back
box.
4 brass screws on the front of the speaker baffle are used to
establish the connection with the amplifier.
See pg. 11 for additional details on making this connection.
ConneCtion
• Use an amp that approximately matches the speaker’s
specified power handling.
• To avoid damage, turn down the volume of the
speaker is distorting, sounds harsh, or the bass begins
to break up.
• Tone controls and equalizers may increase the
likelihood of distortion, especially at high volumes. Use
these setting sparingly.
When you first begin to play your speakers, they may sound
a bit bass shy, due to the high quality, long-life components
used in the drivers. Allow approximately 72 hours of break-in at
90 dB (moderate listening levels) before any critical listening.
Break-in
ProteCt Your investment
Achieving Superior Imaging
For best performance and imaging, place the speakers
equidistant to the primary listening position. It is
recommended that the primary listening position be 1x -2x
the distance between the speakers for optimal imaging. For
example, if your speakers are 10 feet apart, then the optimal
listening distance is between 10 and 20 feet away. Guidance
for speaker height can be found on page 6 in the “Pre-
Installation Checklist” section.
Balancing Hard vs. Soft Surfaces Improves High- and
Mid-Frequency Performance
Rooms that are “overdamped” with carpeting, drapes, and
other sound absorbers can cause your system to be dull
and lifeless. On the other hand, rooms can have so many
hard surfaces that the system sounds like a gymnasium.
Experiment by adding or removing soft surfaces until you find
a mix that is right for you.
sPeaker PlaCement
Fig. 1
WARNING! Turn your amplifier off before
making or breaking any signal connections!
5
Painting the sPeaker grille
IMPORTANT!
Before painting, remove the grille from speakers
and remove the cloth scrim attached inside the grille. The
speaker includes an extra scrim.
1. Remove the grille from the speaker. A protective cloth
scrim is attached to the back of the grille with a low-tack
adhesive. Remove this scrim by gently pulling it away
from the grille and discard it.
2. Paint the grille, being careful not to plug the holes.
Allow the paint to dry completely before proceeding.
IMPORTANT! For best results use a spray rather than a
brush or roller.
3. Gently press the new scrim into place before reinstalling
the speaker grille.
6
Pre-installation CheCklist
NOTE: This is the second part of the Installation process.
Do not proceed until all steps in the “In-wall Back Box
Manual” have been completed.
If using the Statement On-Wall Enclosure you may pro-
ceed from Step 17.
Required Tools:
-3/32 Hex Bit (Not Included)
-5/32 Hex Bit (Not Included)
-Power Drill
-#2 Philips Bit
-#2 Hand Screwdriver
-Medium Grit Sanding Sponge
PLEASE NOTE: INSTALLATION IS A 2 PERSON JOB.
7
Part identifiCation
3
1
3
3
2
3
6
5
4
7
1 Driver Assembly
2 Baffle Protector
3 Handles
4 Trim Baffle
5 End Trim
6 Side Trim
7 Grille
8
sPeaker installation
STEP 16: DRIVER ASSEMBLY INSTALLATION PREPARATION
16a To prepare the back box for the driver assembly
installation, first remove the positioning brackets, 2
corner brackets, and 4 side brackets using a Phillips
screwdriver. These brackets are held in place with 2
screws each.
16b Remove the 10 screws securing the positioning board
and then carefully remove it from the back box.
9
STEP 17: ATTACH TRIM PIECES
17a Before applying the trim pieces, check the interior metal
edge of the install board opening. Sand away any
sheet rock mud buildup so the trim will sit flush with the
surface.
17b Using #2 Phillips screwdriver. apply the top and bottom
trim pieces first, using the supplied machine screws.
(These screws will be in the trim packaging.)
17c Apply the side trim pieces the same way as the top and
bottom pieces.
NOTE: If using the optional on-wall enclosure instead of the
in-wall installation method, please ignore any references to
sheet rock or sheet rock mud, as they only apply to the
in-wall method of installation. All other steps apply to both
methods of installation.
10
STEP 18: MOUNTING THE DRIVER ASSEMBLY
THIS STEP REQUIRES 2 PEOPLE TO COMPLETE SAFELY
18a With 2 people, lift the driver assembly from its
packaging using the attached handles.
18b With 2 people, carefully seat the driver assembly into
the back box by guiding the driver assembly alignment
pins into the mating holes on the back box. Be careful
not to damage the wall surface during this step.
18c While 1 person continues to hold the driver assembly
securely in place, the other should install the included
8-32 screws through the driver assembly into the back
box. These specific locations are marked as “through”
holes in the attached plastic baffle protector. (3/32 hex
driver bit required for machine screws. Not included)
18d Once all 8-32 screws have been tightened, the driver
assembly is now securely attached to the back box.
The person holding the driver assembly in place can
now let go.
18e You may now safely remove the handles and plastic
baffle protector from the driver assembly. (Handle
removal will require the 5/32 hex driver bit. Not
included.)
NOTE: Left channel orientation shown here. Right channel
will be mirrored.
x 4 x 4
11
STEP 19: SECURING THE DRIVER ASSEMBLY
19a After removing the handles and baffle protector, secure
the remaining (27 total) included machine screws.
19b To establish the speaker wire connection with the back
box, carefully tighten the included brass contact screws
with a Phillips screw driver. There are a total of (4)
brass contact screws that need to be installed. 2 on
top, and 2 on bottom. These screw holes are located
directly above the top bass driver and directly below
the bottom bass driver.
NOTE: The speaker will not play if these screws are not
installed.
19c The binding posts located on the front of the Driver
Assembly should only be used for temporary/
troubleshooting purposes and are not intended to be
used during normal operation and can otherwise be
ignored.
12
STEP 20: ATTACH THE FRONT BAFFLE TRIM
20a Carefully align the front baffle trim over the drivers and
press firmly in place to secure.
13
STEP 21 (OPTIONAL): APPLY THE LOGO BADGE
21a Using the included badge application template, attach
the logo to the front baffle trim. This step is optional.
14
STEP 22 (OPTIONAL): APPLY THE SPEAKER GRILLE
22a Gently place the speaker grille over the front
baffle, ensuring a proper fit. The grille is secured
with magnets and may be removed at any time, as
desired. For those wanting to display the drivers of
the Statement 40XW, the grille can remain off. For
installations behind an acoustically transparent screen
it is recommended that the grille remain off.
15
DIMENSIONS
1480.83mm
58.30in
404.45mm
15.92in
1430.03mm
56.30in
353.65mm
13.92in
350.00mm
13.78in
1426.38mm
56.16in
DETAIL B
3.18mm
0.13in
1483.43mm
58.40in
407.06mm
16.03in
DETAIL C
25.80mm
1.02in
16
sPeCifiCations
Frequency Response:.................................48–25,000 Hz ± 3 dB
Tweeter Dispersion (horizontal x vertical).....80° x 52-inch line source
Sensitivity.................................................95 dB @ 2.83 volts/ meter
Impedance...............................................4 ohms. Compatible with 4, 6, or 8 ohm rated amps
Crossover Frequencies..............................300, 2700 Hz
High-Frequency Drivers.............................Sixteen Folded Motion XT Obsidian Tweeters
Mid-Frequency Drivers..............................Sixteen 3.5-inch (8.9 cm) unidirectional carbon fiber
multi-section cone with Nomex® backer and cast aluminum basket, sealed
back chamber format. Concave dust cap
Low-Frequency Drivers..............................Eight 6.5-inch (16.5 cm) unidirectional carbon fiber
multi-section cone with Nomex® backer and cast aluminum basket, sealed
back chamber format. Concave dust cap
Binding Post Inputs...................................Push style (two sets for easy installation)
Crossover Components............................Custom air core coil inductors, polypropylene film capacitors,
and low DF electrolytic capacitors.
Suitable Amplifier Range...........................50–800 watts
Max Power Handling................................400 watts
Weight................................................... 150 lb (68.1 kg)
Required Wall Cavity................................(width) Minimum: 14.5 inch (368 mm)
Maximum: 16.5 inch (420 mm)
Required Wall Cavity................................(height, unobstructed) Minimum: 89 inch (2260 mm)
Required Wall Cavity................................(depth) Minimum: 3.5 inch (89 mm)
Enclosure (width x height x depth, excludes padding)...14.3 x 84.2 x 3.4 inch (361 x 2137 x 86mm)
Grille (height x width)............................................... 11.5 x 59.5 inch (292 x 1511 mm)
*Specifications are subject to change without notice
Manuel de l’ensemble du haut-parleur
MD
18
Check List du contenu . . . . . . . . . . . . . . . . . . . . . . . . 19
Raccordement.............................. 20
Protégez votre investissement .................. 20
Rodage .................................. 20
Positionnement des haut-parleurs ............... 20
Atteindre une imagerie supérieure...............20
L’équilibre entre les surfaces dures et souples améliore
les performances en haute et moyenne fréquence ...20
Peindre la grille du haut-parleur ................ 21
Pré-installation de la check-list ................. 22
Identification des composants .................. 23
Installation .............................24 - 30
Préparation de l’installation de l’ensemble
du haut-parleur............................24
Attacher les pièces de garniture/bordure? .........25
Montage de l’ensemble du haut-parleur ..........26
Fixez l’ensemble du haut-parleur................27
Attachez la paroi avant du baffle ...............28
(Facultatif) Appliquez le badge du logo ...........29
(Facultatif) Appliquez la grille du haut-parleur ......30
Dessin dimensionnel. ........................ 31
Specifications .............................. 32
AVERTISSEMENT!
• Confiez l’entretien à un technicien qualifié.
• Veuillez ne pas exposer ce module à l’humidité
afin d’éviter tout risque d’incendie ou de choc
électrique.
• Veuillez éteindre l’amplificateur en cas de conditions
anormales.
• Veillez à ne pas dépasser la puissance nominale du
haut-parleur.
Conformément à la directive de l’Union européenne
relative aux déchets d’équipements électriques et
électroniques (DEEE) en vigueur depuis le 13 août 2005,
nous souhaitons vous informer que ce produit peut
contenir des matériaux réglementés dont l’élimination,
conformément à la directive DEEE, nécessite une
réutilisation particulière et le traitement du recyclage.
C’est pourquoi Martin Logan a pris des dispositions
avec ses distributeurs dans les pays membres de
l’Union européenne pour collecter et recycler ce produit
gratuitement.
Pour trouver votre distributeur local, veuillez contacter
le revendeur auprès duquel vous avez acheté ce produit,
envoyer un courriel à [email protected] ou
consulter le localisateur de distributeurs à
www.martinlogan.com.Veuillez noter que seul ce
produit relève de la directive DEEE. Lorsque vous vous
débarrassez de l’emballage et des autres matériaux
d’expédition, nous vous encourageons à recycler ces
articles par les voies habituelles
L’éclair avec symbole en pointe de flèche à
l’intérieur d’un triangle équilatéral est prévu
pour alerter l’utilisateur de la présence d’une
“tension dangereuse” non isolée dans l’enceinte
du produit, qui peut être d’une amplitude
suffisamment élevée pour constituer un risque de
choc électrique.
Le point d’exclamation à l’intérieur d’un triangle
équilatéral est prévu pour signaler à l’utilisateur
la présence d’instructions importantes de
fonctionnement et d’entretien (maintenance) dans
la documentation accompagnant l’appareil.
Le feu à l’intérieur d’un triangle équilatéral est
prévu pour alerter l’utilisateur sur la possibilité
de créer un risque d’incendie s’il ne suit pas les
instructions.
Le signe du dollar dans un triangle équilatéral
est prévu pour avertir l’utilisateur qu’il risque de
causer des dommages dont la réparation pourrait
19
Check List du contenu
Le Statement 40XW complet est expédié dans 3 boîtes. Ce manuel concerne la boîte 3 sur 3 qui est l’ensemble du haut-
parleur. L’ensemble du haut-parleur Statement 40XW contient les éléments suivants.
Si vous avez besoin de notre assistance, veuillez appeler notre service au (785) 749-0133.
Ensemble du haut-parleur 40XW - Paroi avant du baffle - Cache grille du haut-parleur - Grille supplémentaire - Pièces de la
paroi - Vis de machine 4x vis en laiton - Badge et modèle du logo MartinLogan
20
The amplifier is connected to the Statement 40XW
through the binding posts located on the top or
bottom of the in wall back box.
4 vis en laiton à l’avant du baffle du haut-parleur servent à
établir la connexion avec l’amplificateur.
Voir p. 11 pour plus de détails sur comment établir cette
connexion.
raCCordement
• Utilisez un amplificateur qui correspond
approximativement à la puissance spécifiée du haut-
parleur.
• Pour éviter tout dégâts, baissez le volume si le son du
haut-parleur se distord, s’il est dur ou si les basses
commencent à se casser.
• Les contrôles de tonalité et les égaliseurs peuvent
augmenter la probabilité de distorsion, en particulier
à des volumes élevés. Utilisez ces réglages avec
modération.
Lorsque vous commencez à utiliser vos haut-parleurs, ils peu-
vent sembler un peu faibles au niveau des basses, en raison
des composants de haute qualité et de longue durée de vie
utilisés dans les haut-parleurs. Prévoyez environ 72 heures
de rodage à 90 dB (niveaux d’écoute modérés) avant toute
écoute critique.
rodage
Protégez votre investissement
Atteindre une imagerie supérieure
Pour obtenir les meilleures performances et une imagerie
optimale, placez les haut-parleurs à une distance égale l’un
de l’autre et évitez les obstacles physiques entre le haut-
parleur et la position d’écoute principale. Il est recommandé
de placer la position d’écoute principale à une distance
égale à 1x -2x la distance entre les haut-parleurs pour
obtenir une imagerie optimale. Par exemple, si vos haut-
parleurs sont distants de 3 mètres, la distance d’écoute
optimale se situe entre 3 et 6 mètres. Des indications sur la
hauteur des haut-parleurs se trouvent à la page 6 dans la
section “ Check-list de pré-installation “.
L’équilibre entre les surfaces dures et souples améliore les
performances en haute et moyenne fréquence
Les pièces “ encombrées “ de moquette, de rideaux et
d’autres absorbeurs de sons peuvent rendre votre système
terne et sans vie. D’autre part, les pièces peuvent avoir
tellement de surfaces dures que le système ressemble à un
gymnase. Faites des expériences en ajoutant ou en enlevant
des surfaces souples jusqu’à ce que vous trouviez un
mélange qui vous convienne.
Positionnement des haut-Parleurs
Fig. 1
AVERTISSEMENT ! Éteignez votre amplificateur
avant d’établir ou d’interrompre toute
connexion de signal !
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
