Lenco Turntable Manuel utilisateur

Model: LBT-188

User manual - Turntable with bluetooth transmission

Gebruikshandleiding - Platenspeler met Bluetooth-overdracht

Bedienungsanleitung - Plattenspieler mit Bluetooth-

Ü

bertragung

Guide d’utilisation - tourne-disque avec transmission Bluetooth

Manual de usuario – Tocadiscos con transmisión Bluetooth

1

Index

English

.................................................................................................................

2

Nederlands

........................................................................................................

25

Deutsch

.............................................................................................................

50

Fran

ç

ais

.............................................................................................................

75

Español

............................................................................................................

101

Version: 4.0

2

English

LBT-188

CAUTION:

Usage of controls or adjustments or performance of procedures other than

those specified herein may result in hazardous radiation exposure.

PRECAUTIONS BEFORE USE

KEEP THESE INSTRUCTIONS IN MIND:

1. Do not cover or block any ventilation openings. When placing the device

on a shelf, leave 5 cm (2”) free space around the whole device.

2. Install in accordance with the supplied user manual.

3. Keep the device away from heat sources such as radiators, heaters,

stoves, candles and other heat-generating products or naked flame. The

apparatus can only be used in moderate climates. Extremely cold or

warm environments should be avoided. Working temperature between

0° and

35° C.

4. Avoid using the device near strong magnetic fields.

5. Electrostatic discharge can disturb normal usage of this device. If so,

simply reset and restart the device following the instruction manual.

During file transmission, please handle with care and operate in a

static-free environment.

6. Warning! Never insert an object into the product through the vents or

openings. High voltage flows through the product and inserting an

object can cause electric shock and/or short circuit internal parts. For

the same reason, do not spill water or liquid on the product.

7. Do not use in wet or moist areas such as bathrooms, steamy kitchens or

near swimming pools.

8. The apparatus shall not be exposed to dripping or splashing and make

sure that no objects filled with liquids, such as vases, are placed on or

near the apparatus.

9. Do not use this device when condensation may occur. When the unit is

used in a warm wet room with damp, water droplets or condensation

may occur inside the unit and the unit could maybe not work properly;

let the unit stand in power OFF for 1 or 2 hours before turning on the

power: the unit should be dry before getting any power.

3

10. Although this device is manufactured with the utmost care and checked

several times before leaving the factory, it is still possible that problems

may occur, as with all electrical appliances. If you notice smoke, an

excessive build-up of heat or any other unexpected phenomena, you

should disconnect the plug from the main power socket immediately.

11. This device must operate on a power source as specified on the

specification label. If you are not sure of the type of power supply used

in your home, consult your dealer or local power company.

12. Keep away from rodents. Rodents enjoy biting on power cords.

13. To clean the device, use a soft dry cloth. Do not use solvents or petrol

based fluids. To remove severe stains, you may use a damp cloth with

dilute detergent.

14. The supplier is not responsible for damage or lost data caused by

malfunction, misuse, modification of the device or battery replacement.

15. Do not interrupt the connection when the device is formatting or

transferring files. Otherwise, data may be corrupted or lost.

16. If the unit has USB playback function, the usb memory stick should be

plugged into the unit directly. Don’t use an usb extension cable because

it can cause interference resulting in failing of data.

17. The rating label has been marked on the bottom or back panel of the

apparatus.

18. This device is not intended for use by people (including children) with

physical, sensory or mental disabilities, or a lack of experience and

knowledge, unless they’re under supervision or have received

instructions about the correct use of the device by the person who is

responsible for their safety.

19. This product is intended for non professional use only and not for

commercial or industrial use.

20. Make sure the unit is adjusted to a stable position. Damage caused by

using this product in an unstable position vibrations or shocks or by

failure to follow any other warning or precaution contained within this

user manual will not be covered by warranty.

21. Never remove the casing of this apparatus.

22. Never place this apparatus on other electrical equipment.

23. Do not allow children access to plastic bags.

24. Only use attachments/accessories specified by the manufacturer.

4

25. Refer all servicing to qualified service personnel. Servicing is required

when the apparatus has been damaged in any way, such as the power

supply cord or the plug, when liquid has been spilled or objects have

fallen into the apparatus, when the apparatus has been exposed to rain

or moisture, does not operate normally, or has been dropped.

26. Prolonged exposure to loud sounds from personal music players may

lead to temporary or permanent hearing loss.

27. If the product is delivered with power cable or AC power adaptor :

 If any trouble occur, disconnect the AC power card and refer

servicing to qualified personnel.

 To completely disconnect the power input, the mains plug of the

apparatus shall be disconnected from the mains, as the disconnect

device is the mains plug of apparatus.

 Don’t step on or pinch the power adaptor. Be very careful,

particularly near the plugs and the cable’s exit point. Do not place

heavy items on the power adaptor, which may damage it. Keep the

entire device out of children’s reach! When playing with the power

cable, they can seriously injure themselves.

 Unplug this device during lightning storms or when unused for a

long period.

 The socket outlet must be installed near the equipment and must

be easily accessible.

 Do not overload ac outlets or extension cords. Overloading can

cause fire or electric shock.

 Devices with class 1 construction should be connected to a main

socket outlet with a protective earthed connection.

 Devices with class 2 construction do not require a earthed

connection.

 Always hold the plug when pulling it out of the main supply socket.

Do not pull the power cord. This can cause a short circuit.

 Do not use a damaged power cord or plug or a loose outlet. Doing

so may result in fire or electric shock.

28. If the product contains or is delivered with a remote control containing

coin / cell batteries:

Warning:

 “Do not ingest battery, Chemical Burn Hazard” or equivalent

working.

5

 [The remote control supplied with] This product contains a coin /

button cell battery is swallowed, it can cause severe internal burns

in just 2 hours and can lead to death.

 Keep new and used batteries away from children.

 If the battery compartment does not close securely, stop using the

product and keep it away from children.

 If you think batteries might have been swallowed or placed inside

any part of the body, seek immediate medical attention.

29. Caution about the use of Batteries:

 Danger of explosion if battery is incorrectly replaced. Replace only

with the same or equivalent type.

 Battery cannot be subjected to high or low extreme temperatures,

low air pressure at high altitude during use, storage or transportation.

 Replacement of a battery with an incorrect type that can result in

an explosion or the leakage of flammable liquid or gas.

 Disposal of a battery into fire or a hot oven, or mechanically

crushing or cutting of a battery, that can result in an explosion.

 Leaving a battery in an extremely high temperature surrounding

environment that can result in an explosion or that leakage of

flammable liquid or gas.

 A battery subjected to extremely low air pressure that may result in

an explosion or the leakage of flammable liquid or gas.

 Attention should be drawn to the environmental aspects of battery

disposal.

INSTALLATION

• Unpack all parts and remove protective material.

• Do not connect the unit to the mains before checking the mains voltage

and before all other connections have been made.

* Those instructions are related only to products using power cable or AC

power adaptor.

6

COMPONENTS, FEATURES AND CONNECTIONS

10. Lid

11. Lid Hinge

12. Ground Connector

13. PHONO & Line Out Jacks

14. PHONO & Line Out Switch

15. Anti-skating Weight

16. USB-PC port

17. AC-DC Power Jack

18. Bluetooth Indicator

19. Power Rocker Switch

Please check thoroughly and make sure you find the following items that

1. Counterweight

2. Anti-skating Stub

3. Turntable Platter

4. Tonearm Lift Lever

5. Tonearm Rest

6. 33/45 Selector

7. Tonearm

8. Stop/Start Knob

9. Cartridge

7

come along with this package:

1) Unit

2) Adaptor with EU-UK plug-end

3) Counterweight

4) Platter with Belt

5) 45 RPM Adaptor

6) Turntable mat

7) Instruction Manual

8) Cartridge Alignment Protractor

9) USB-PC Cable

10) 2pcs lid spare rubber

11) Anti-skating Weight

12) Line out cable

This turntable is supplied with a factory fitted and adjusted cartridge.

**The following instructions for adjusting the cartridge are provided in case

the cartridge is replaced by a different model at a later date.

Installing the Lid

Install the Lid carefully over the hinge prongs.

Turntable Platter and Belt Setup

1. Install the drive belt over the inner ring under the platter and make sure

it won

’

t fall off during the setup.

2. Place the platter through the turntable spindle,

then rotate the platter until you see the drive

motor pulley through the window at the top

left corner.

3. Carefully grab the drive belt and put it around

the slot of motor pulley.

4. Connect the power adapter to the turntable and power on the turntable.

5. Set the Motor Start/Stop switch to the Start position to see if the platter

motor spins. If the platter does not spin, try the steps listed above again.

8

Cartridge Down force Adjustment

The Counterweight supplied is suitable for cartridges weighing between

3.0-6.0g.

-

Gently push and turn the Counterweight onto the rear of the tonearm

(with the scale facing toward the front of the turntable).

- Remove the cartridge protection cap.

-

Lower the tonearm lift and position the cartridge in the space between

tonearm rest and platter.

Carefully rotate the Counterweight until the tonearm balances out. The

tonearm should return to the balanced position if it is moved up or down.

This adjustment must be done carefully.

- Once the tonearm is correctly balanced return it to its’ rest. Hold the

Counterweight without moving it, and gently rotate the Down force Scale

ring until the zero is in line with black line on the rear of the tonearm.

Check whether the arm still balances out.

9

- Rotate the counterweight counter clockwise (seen from the front) to adjust

the down force according to the cartridge manufacturer

’

s

recommendations. One mark on the scale represents 0.05g of down force.

NOTE: The recommended down force for the factory fitted cartridge is

3.0±0.5g.

Locate the anti-skating weight

You will find a anti-skating weight with small fishing line from the package,

please follow below steps to locate the anti-skating weight:

1. Slip the looped end of the fishing line over the anti-skating weight

adjustment stub and into Groove 3

rd

(the correct anti-skating force for

the factory-fitted cartridge).

2. Pull the anti-skating weight slightly to let the tie of the fishing line move

to the stub.

3. Lift the anti-skating weight over the anti-skating weight wire support.

10

The anti-skating weight should now be dangling in free space to the left

of support.

Slip the loop of the anti-skating weight's thread over the 3nd groove of the

stub to set the correct anti-skating force for the factory-fitted cartridge. Feed

the thread through the loop of the wire support.

Anti-skating force adjustment

The anti-skating force must be adjusted corresponding to the down force as

follows:

Down force

Groove in the stub

5 - 10mN

1 st from bearing rings

10 - 15mN

15

–

20mN

2 nd " " "

3

rd

" " "

20mN and bigger

4 th " " "

Slip the loop of the anti-skating weight's thread over the 3rd groove of the

stub to set the correct anti-skating force for the factory-fitted cartridge. Feed

the thread through the loop of the wire support.

Stereo System connection

RCA Jacks

·

The RCA Jacks of this unit are shared as both the Phone output jacks and the

11

Line output jacks. They are determined by the Phono/Line Switch.

·

When used as a line output, the jacks output analog line-level signals and

could be connected directly with a pair of active speakers or the appropriate

input of your stereo system. When used as a Phono output, they should be

connected to the phono pre-amplifier or the phono input of the stereo

system.

· The Red plug connects with the Right channel and the White plug connects

with the Left channel.

Note:

· If the Phono/Line switch is set at LINE position but RCA jacks connected to

the stereo system

’

s phono input, the sound might be distorted due to input

overload and could damage your stereo system.

· If the Phono/Line switch is set at PHONO position but RCA jacks connected

to the stereo system’s line input, the volume will be very low due to lacking

signal pre-amplification.

RCA Jack is not designed to be connected directly to the passive/unpowered

speakers and if it does, the volume will be very low.

Main Power Connection

The power adaptor is in the foam packing material. Unpack the power

adaptor and plug the small end into the DC power jack located at the back

side of the turntable. Plug the power adaptor into your power outlet.

Operation

Turntable Operation

1. Connect the included power adapter to unit and press the power rocker

switch to be

“

ON

”

position.

2. Remove the needle cover from the cartridge.

3. Place the slipmat on the platter and place a record on the slipmat. If

using 45 RPM records, put the 45 RPM adapter on the center spindle

12

before placing the record on the platter.

4. Set the 33/45 RPM Selector according to the type of record.

5. Turn the Start/Stop dial to the Start position to begin spinning the

platter.

6. Unlock the arm clip and set the Lift Lever to the up position.

7. Position the tonearm over the desired location (groove) on the record.

8. Move the tonearm lift lever to the down position to move the tonearm

toward the record. Alternatively, place the needle over the desired

location on the record.

9. Carefully lower the tonearm on the record.

10. When you are finished playing the record, raise the tonearm, return it to

rest on the arm clip, and turn the Start/Stop dial to the Stop.

Bluetooth Operation

This unit has a Bluetooth transmitter to send audio to a Bluetooth speaker

wirelessly.

1. Power on your Bluetooth speaker and ensure it is in pairing mode.

2. Power on the unit, the BT will auto search when the unit turn on, the BT

indicated light flashing.

3. When pairing, the light will flash twice per second, then change to be

long lighting when paired;

Note: This unit will connect to the closest Bluetooth speaker that is near

it. If after 2 minutes no Bluetooth speaker can be found to pair with, the

Bluetooth transmitter will become inactive and the LED will turn off.

4. To disconnect pairing, power off the turntable or turn off Bluetooth

pairing on your Bluetooth speaker.

“This product has a bluetooth transmission function, you can not receive any

bluetooth sound on it: this means that you can transmit wirelessly a

bluetooth sound signal to an external device like a bluetooth speaker,

13

bluetooth headphone, audio system with bluetooth reception,…”

Recording the LP into PC through USB jack:

For installing and recording step please reference to the BRIEF

INTRODUCTION OF AUDACITY. http://audacity.sourceforge.net/

Recording the vinyl to your computer:

1). Follow the detail step as above Turntable Operation to play the vinyl.

2). Double click the Audacity and follow the record steps showing on the

BRIEF INTRODUCTION OF AUDACITY.

Audacity and USB Connection

It supports Windows95/Window XP/Window 7/Vista or more advanced

version, with the EMS memory more than 128MB and Audacity take space of

5MB.

Instruction for PC Encoding

1. Software instruction

1.1) Connect the USB cable with your turntable and your computer.

No extra driver is required.

1.2) Download the Audacity software from http://audacity.sourceforge.net/

Follow the instructions to complete installation.

2. Recording

2.1) Open the software

14

2.2) Choose “Edit” menu, then choose “Preferences”;

2.3) Audacity Preferences

NOTE: you need to check your computer audio properties, the sound

recording should be selected: SSS USB Audio Device” as below:

15

2.4) Adjust the output and input volume

Output volume

Input Volume

2.5) Select the record button

●

to record the disc, the left and right tracks will

show on the interface:

16

2.5.1 ⑤ Press this button , start recording.

2.5.2

⑥

Click the button to skip to start;

2.5.3 ⑦ Click the button to skip to end;

2.5.4 ⑧ Click the button to play;

2.5.5

⑨

Click the button to pause the record play;

2.5.6 ⑩ Click the button to stop the recording.

3. Export the Music Files for WAV, MP3, Format.

· Once you have finished recording, you should save your music to the

computer.

· Click File menu and move down to Export as WAV format, MP3 format or

Ogg format.

·

Click on any format to save the music, and you will be asked for the file

name of the music recording.

· Note: Audacity does not export MP3 files directly; you should download the

LAME MP3 encoder. A link to find LAME MP3 can be found at

17

http://audacity.sourceforge.net

If do not see the sound wave on the interface, when recording, please

adjust the line in volume as follows:

Specific Steps as follows:

1) Download “lame_enc.dll” file, and install it to the software list.

2) Open the “Audacity” software, click Main Menu, Select “edit”,

“

Parameter

”

,

“

File Formats

”

, and click the

“

Searcher

”

.

18

3) After opened, it will come to the following menu, click “YES” to go to

“

Llame_enc.dll

”

, and find the file

’

s location.

4) After you find the “lame_enc.dl” file, open it and click “Y” to finish the

installation.

19

Maintenance and Cleaning

Your turntable requires little of no regular maintenance. Remove dust with a

slightly damp antistatic cloth. Never use a dry cloth, this will create static

electricity and attract more dust! Antistatic cleaning agents are available at

specialist stores, but must be applied sparingly to avoid damage to rubber

parts. It is recommended to install the needle cover before cleaning or

maintenance is carried out to avoid damage.

If the turntable is not used over a long period of time, the drive belt should

be removed to prevent unequal stretching.

NOTE: Always disconnect the record player from the power supply as a

precaution before maintenance!

Useful Tips

The turntable should be positioned on a low-resonance surface such as wood

or multiple layer ply board to avoid structural vibrations disturbing playback.

Cartridge Replacement

1. Before replacement, put the stylus protector back on the stylus to

prevent damage to the stylus during the replacement process.

2. Carefully remove the wire leads from the original cartridge.

3. Loosen the two screws on the headshell that are securing the cartridge

and then remove the original cartridge.

4. Mount the new cartridge to the headshell and tighten it lightly. Do not

completely tighten the screws at this moment.

5. Connect the wire leads to the new cartridge

’

s terminals. The wire lead

color codes are as below:

White Left channel positive (L+)

Black Left channel negative (L

–

)

La page charge ...

Lenco Turntable Manuel utilisateur

Ce manuel convient également à

Lenco Turntable Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents