Philips SCD506 Manuel utilisateur

SCD506

34

35

26

2

1

3

4

5

13

12

14

33

16

36

18

15

6

7

8

11

20

19

21

22

23

24

25

32

31

9

28

27

29

30

10

17

1

English 6

Dansk 16

Deutsch 26

Español 37

Français 48

Italiano 59

Nederlands 70

Norsk 81

Português 91

Suomi 102

Svenska 112

Türkçe 122

Ελληνικα

132

ﺔﻴﺑﺮﻌﻟﺍ

143

2

3

2

1

4

5

6

7

8

9

>

3.5ft/1m

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

English

Introduction

Congratulations on your purchase and welcome to Philips Avent! To fully benefit from the support

that Philips Avent offers, register your product at www.philips.com/welcome.

Philips Avent is dedicated to producing caring, reliable products that give parents the reassurance

they need. This Philips Avent baby monitor provides round-the-clock support by ensuring you can

always hear your baby clearly without any distracting noise. The DECT technology guarantees zero

interference and a crystal clear sound between the baby unit and the parent unit.

General description (Fig. 1)

1 Parent unit

2 'Talk' button

3 'Sensitivity' button

4 'Link' light

5 Speaker

6 Microphone

7 Sound level lights

8 ECO Max button with light

9 Battery status light

10 Volume + and - buttons

11 On/off button

12 Neck strap loop

13 Battery compartment

14 Socket for small plug

15 Lid of battery compartment

16 Rechargeable batteries

17 Adapter with small plug

18 Neck strap

19 Baby unit

20 Nightlight

21 Microphone

22 PAGE button

23 Power-on light

24 On/off button

25 Speaker

26 Battery status light

27 Volume + button

28 Volume - button

29 Lullaby play/stop button

30 Next lullaby button

31 Nightlight on/off button

32 Battery compartment

33 Socket for small plug

34 Lid of battery compartment

35 Non-rechargeable 1.5 V R6 AA batteries (not supplied)

36 Adapter with small plug

Important safety information

Read this important information carefully before you use the appliance and save it for future

reference.

6

English

IMPORTANT

This baby monitor is intended as an aid. It is not a substitute for responsible and proper adult

supervision and should not be used as such.

Never leave your baby alone in your home. Always make sure there is someone present to look after

the baby and take care of its needs.

Disclaimer

Please note that you use this baby monitor at your own risk. Koninklijke Philips N.V. and its subsidiary

companies are not responsible for the operation of this baby monitor or your use of it and therefore

do not accept any liability in connection with your use of this baby monitor.

Danger

-

Never immerse any part of the baby monitor in water or any other liquid. Do not place the

appliance where water or any other liquid can drip or splash onto it. Never use the baby monitor in

moist places or close to water.

-

Never put any object on top of the baby monitor and do not cover it. Do not block any ventilation

openings. Install according to the manufacturer’s instructions.

-

Cords present a potential strangulation hazard. Keep cords out of the reach of children (more than

1 meter/3.5 feet away). Never place the baby monitor inside the baby’s bed or playpen (Fig. 2).

-

There is a danger of explosion if disposable or rechargeable batteries are replaced incorrectly. Only

replace them with the same type.

Warning

-

Check if the voltage indicated on the adapter corresponds to the local mains voltage before you

connect the appliance.

-

Do not modify or cut off any part of the adapter and its cord, as this causes a hazardous situation.

-

Only use the adapter supplied (model S003PV0600050).

-

If the adapter is damaged, always have it replaced with one of the original type in order to avoid a

hazard.

-

This appliance can be used by children aged from 8 years and above and persons with reduced

physical, sensory or mental capabilities or lack of experience and knowledge if they have been

given supervision or instruction concerning use of the appliance in a safe way and understand the

hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall

not be made by children without supervision.

-

Protect the mains cord from being walked on or pinched particularly at plugs, convenience

receptacles, and the point where they exit from the appliance.

-

Make sure that you place the baby monitor in such a way that its cord does not obstruct a doorway

or passage. If you place the baby monitor on a table or low cabinet, do not let the mains cord hang

over the edge of the table or worktop. Make sure the cord does not lie on the floor where it

presents a tripping hazard.

-

Keep the packaging materials (plastic bags, cardboard buffers, etc.) out of the reach of children, as

they are not a toy.

-

To prevent electric shock, do not open the housing of the baby unit or parent unit except for the

battery compartments.

Caution

-

Use the appliance at a temperature between 0°C (32°F) and 40°C (104°F).

7

English

-

Do not install the appliance near any heat sources such as radiators, heat registers, stoves or other

apparatus (including amplifiers) that produce heat.

-

Make sure that your hands are dry when you handle adapters, plugs and mains cord and also

when you insert or replace disposable and rechargeable batteries.

-

All the required markings are located on the battery compartment of the parent unit and baby unit

and on the bottom enclosure of the charger (if any).

-

For the parent unit, only use the rechargeable battery supplied with the baby monitor.

-

Charge the rechargeable battery as described in the user manual.

-

The parent unit can only be recharged with the rechargeable battery supplied.

-

To prevent battery explosion or leakage, which can damage the baby monitor and cause burns and

skin or eye irritation:

-

Do not recharge non-rechargeable batteries in the parent unit.

-

Remove rechargeable and disposable batteries if you are not going to use the baby monitor for

more than 30 days.

-

Make sure the + and - poles of the batteries point in the right direction.

-

Keep the batteries away from excessive heat such as sunshine, fire or the like.

-

Do not leave empty batteries in the baby unit.

-

To prevent batteries from heating up or releasing toxic materials, hydrogen or oxygen, do not

overcharge, short-circuit, reverse charge or damage batteries.

-

To handle damaged or leaking batteries, wear protective gloves to protect your skin.

Compliance with standards

-

This product complies with the radio interference requirements of the European Community (Fig.

3).

-

Philips Consumer Lifestyle hereby declares that this baby monitor is in compliance with the

essential requirements and other relevant provisions of Directive 2014/53/EU (DECT: frequency

band 1880-1900 MHz, maximum radio-frequency power: 250 mW). A copy of the EC Declaration of

Conformity (DoC) is available online at www.philips.com/support.

Electromagnetic fields (EMF)

This Philips appliance complies with all applicable standards and regulations regarding exposure to

electromagnetic fields.

Preparing for use

Baby unit

We advise you to operate the baby unit from the mains. To guarantee automatic power backup in

case of mains failure, you can insert four 1.5V AA alkaline batteries (not included).

Do not use rechargeable batteries. The baby unit does not have a charging function and rechargeable

batteries discharge slowly when they are not in use.

1 Remove the lid of the battery compartment (Fig. 4).

2 Insert four non-rechargeable 1.5V R6 AA batteries. Make sure that the + and - poles point in the

right direction (Fig. 5).

3 Reattach the lid.

4 Put the small plug in the baby unit and put the adapter in the wall socket (Fig. 6).

8

English

Parent unit

The parent unit runs on two rechargeable 850mAh Ni-MH batteries that are supplied with the baby

monitor. Charge the parent unit before you use it for the first time and when the batteries are low.

1 Make sure that the parent unit is switched off and disconnected from the mains.

2 Remove the lid of the battery compartment (Fig. 7).

3 Insert the rechargeable batteries. Make sure that the + and - poles point in the right direction (Fig.

8).

4 Reattach the lid.

5 Put the power adapter in the parent unit and put the adapter in the wall socket (Fig. 9).

The battery status indicator flashes green to indicate that the appliance is charging.

Note: It takes 4 charge and discharge cycles before the rechargeable batteries reach their full capacity.

The normal charging time is 10 hours, and the normal operating time is 24 hours.



Rechargeable batteries:

Manufacturer

Model Rating

BYD H-AAA850A-MB20 1.2V Ni-MH AAA/R03 850mAh

GPI PH85AAAHC 1.2V Ni-MH AAA/R03 850mAh

Adapters:

UK model number

S003PB0600050

EU model number S003PV0600050

Using the baby monitor

Positioning the baby monitor

Keep the baby unit out of the reach of the baby. Never place the baby unit inside the baby’s bed or

playpen.

Because the cord of the baby unit presents a potential strangulation hazard, make sure that the baby

unit and its cord are at least 1 metre/3.5 feet away from your baby. (Fig. 10)

To prevent a high-pitched sound from one or both units, make sure the parent unit is at least 1.5

metres/5 feet away from the baby unit.

Note: When the parent unit is out of range of the baby unit, the parent unit beeps from time to time.

The link indicator on the parent unit flashes red.

Linking parent unit and baby unit

1 Press and hold the on/off button on the baby unit for two seconds (Fig. 11).

-

All lights on the baby unit light up briefly.

2 Press and hold the on/off button on the parent unit for two seconds (Fig. 12).

-

All lights on the parent unit light up briefly.

-

The 'link' light flashes red and the parent unit starts to search for the baby unit.

-

When the parent unit and baby unit are linked, the 'link' light turns solid green (Fig. 13).

9

English

-

If no connection is established, the 'link' light flashes red and the parent unit beeps from time to

time.

Note: It takes less than 15 seconds to establish the link between the parent unit and the baby unit.

What to do if no link is established

-

If the parent unit is out of range, place it closer to the baby unit, but not closer than 1 metre/3.5

feet.

-

If the baby or parent unit is too close to another DECT appliance (e.g. a cordless phone), switch off

this appliance or move the unit away from this appliance.

-

If the baby unit is switched off, switch it on.

Operating range

-

The operating range is 330 metres/1000 feet outdoors and up to 50 metres/150 feet indoors.

-

The operating range of the baby monitor varies depending on the surroundings and factors that

cause interference. Wet and moist materials cause so much interference that the range loss is up to

100%. For interference from dry materials, see the table below.

Dry materials

Material thickness Loss of range

Wood, plaster, cardboard,

glass (without metal, wires

or lead)

< 30cm (12in) 0-10%

Brick, plywood < 30cm (12in) 5-35%

Reinforced concrete < 30cm (12in) 30-100%

Metal grilles or bars < 1cm (0.4in) 90-100%

Metal or aluminium sheets < 1cm (0.4in) 100%



Functions and feedback on the baby unit

Nightlight

The nightlight produces a soft glow that comforts your baby.

1 Press the nightlight button on the back of the baby unit to switch on the nightlight (Fig. 14).

2 Press the nightlight button again to switch off the nightlight.

Lullaby function

1 Press the lullaby play/stop button on the baby unit to play the last selected lullaby (Fig. 15).

The selected lullaby repeats for 30 minutes.

2 Press the next lullaby button to select another lullaby from the list (Fig. 16).

3 To adjust the sound level of the lullaby, press the + or – button on the baby unit.

4 To stop lullaby playing, press the lullaby play/stop button on the baby unit.

10

English

Paging the parent unit

If you have lost the parent unit, you can use the PAGE button on your baby unit to locate the parent

unit. This function only works when the parent unit is switched on.

1 Press the PAGE button on the baby unit (Fig. 17). The parent unit produces a paging alert tone.

2 To stop the paging alert tone, press the PAGE button on the baby unit again or press any button

on the parent unit. The paging alert tone stops automatically after 2 minutes.

Battery status light

The battery status light is solid green when the baby unit is operating on battery power and the

batteries contain enough energy.

The battery status light flashes red quickly when the batteries run low while the baby unit is operating

on battery power (Fig. 18).

Note: The battery status light is off when the baby unit is powered by the adapter.

Replace the batteries when they run low.

Functions and feedback on the parent unit

Volume

There are five volume levels and a 'volume off' setting.

Setting the volume level

1 Press the + button or the - button once.

The sound level lights show the current volume (Fig. 19).

2 Press the + button to increase the volume or press the - button to decrease the volume.

3 If you do not press a button for more than 3 seconds, the sound level lights go out and the setting

is saved.

Volume off

Below the lowest volume setting, there is a 'volume off' setting.

1 Press the + button or the - button once.

The sound level lights show the current volume.

2 Press and hold the - button for more than 3 seconds to set the volume to off.

Note: The sound level lights always show that the baby produces sounds, even if the volume is set to

off.

Talk function

1 If you want to comfort your baby, press the TALK button on the parent unit and talk clearly into the

microphone on the front from a distance of 15-30cm (0.5-1ft) (Fig. 20).

The 'link' light starts flashing green.

Note: If you have set the volume for the lullaby higher on the baby unit, the sound will also be

louder when you use the talk function on the parent unit.

2 Release the TALK button when you have finished talking.

11

English

Battery status light

When the rechargeable batteries of the parent unit are low, the battery status light flashes red and the

parent unit beeps (Fig. 21). The remaining operating time is at least 30 minutes.

When the rechargeable battery of the parent unit is almost empty, the battery status light flashes red.

If you do not connect the parent unit to the mains to charge it when the battery status light flashes

red, the parent unit switches off.

The battery status light flashes green when the parent unit is charging (Fig. 21).

Microphone sensitivity

This option allows you to set the microphone sensitivity of the baby unit. The microphone sensitivity

determines what noise level the baby unit picks up, e.g. you will want to hear when your baby cries,

but you may be less interested in its babbling.

Note: The parent unit uses less power when it is set to a lower sensitivity level.

1 Press the 'sensitivity' button once (Fig. 22).

The sound level lights light up briefly and show the current sensitivity level (Fig. 19).

2 Press the 'sensitivity' button again within 3 seconds to increase the sensitivity level.

When the maximum sensitivity level has been reached, the lowest sensitivity level will be selected

again.

3 If you do not press a button for more than 3 seconds, the sound level lights go out and the setting

is saved.



ECO mode

Smart ECO is a standard feature on this baby monitor. It automatically reduces the DECT signal from

the baby unit to save energy. To save even more energy, activate the ECO Max mode. In this mode,

the DECT signal of the baby unit is switched off as long as the baby does not make a sound.

Caution: When the baby makes a sound, there may be a slight delay in response because the DECT

signal has to switch on again before the baby unit can send feedback to the parent unit.

Please note the following:

-

In ECO Max mode, you do not receive feedback when the baby unit is switched off or when the

parent unit is out of range of the baby unit. You can check the connection by pressing any button

on the parent unit.

Activating the ECO Max mode

Make sure that the parent unit is linked to the baby unit.

1 Press the ECO Max button (Fig. 23).

The ECO Max indicator lights up blue.The 'link' light starts flashing green slowly approx. 1 minute

after the baby has stopped making sounds (Fig. 24).

When the parent unit receives a DECT signal from the baby unit because the baby makes a sound,

the 'link' light turns solid green.

Deactivating ECO Max mode

1 Press the ECO Max button (Fig. 23).

The ECO Max indicator goes out.

12

English

Warranty and support

If you need information or support, please visit www.philips.com/support or read the international

warranty leaflet.

Recycling

-

This symbol means that this product shall not be disposed of with normal household waste

(2012/19/EU) (Fig. 25).

-

This symbol means that this product contains rechargeable and disposable batteries which shall

not be disposed of with normal household waste (2006/66/EC) (Fig. 26).

-

Follow your country's rules for the separate collection of electrical and electronic products, and

rechargeable and disposable batteries. Correct disposal helps prevent negative consequences for

the environment and human health.

Removing rechargeable and disposable batteries

To remove rechargeable and disposable batteries, see the instructions for placing and/or removing

batteries in the user manual.

Frequently asked questions

Question

Answer

Why don't the power-on light

of the baby unit and the 'link'

light of the parent unit light up

when I press the on/off

buttons of the units?

Perhaps the rechargeable battery of the parent unit is empty and

the parent unit is not plugged in. Put the small plug in the parent

unit and put the adapter in a wall socket. Then press the on/off

button to establish connection with the baby unit.

Perhaps the non-rechargeable batteries of the baby unit are empty

and the baby unit is not connected to the mains. Replace the non-

rechargeable batteries or connect the baby unit to the mains. Then

press the on/off button to establish connection with the parent unit.

Why doesn't the battery status

light on the parent unit light

up when I start recharging the

parent unit?

It takes a few minutes before the battery status lightlights up,

especially when the parent unit is charged for the first time or has

not been in use for a long period.

Is my baby monitor secure

from eavesdropping and

interference?

The DECT technology of this baby monitor guarantees no

interference from other equipment and no eavesdropping.

Why does the parent unit

beep?

If the parent unit beeps while the 'link' light fashes red, the

connection with the baby unit is lost. Move the parent unit closer to

the baby unit to re-establish the connection between the parent

unit and the baby unit.

If the parent unit beeps and the battery status light flashes red,

recharge the parent unit.

If the baby unit is switched off, switch on the baby unit.

13

English

Question Answer

Why does the parent unit

produce a high-pitched noise?

The units may be too close to each other. Make sure that the parent

unit and the baby unit are at least 1.5 metres/5 feet away from each

other. It takes a few seconds for the high-pitched noise to stop.

The volume of the parent unit may be too high. Decrease the

volume of the parent unit.

Why don't I hear a sound/ Why

can't I hear my baby cry?

The volume of the parent unit may be too low or may be switched

off. Increase the volume of the parent unit.

The microphone sensitivity level of the baby unit may be too low.

Increase the microphone sensitivity level on the parent unit.

The baby unit and the parent unit may be out of range of each

other. Reduce the distance between the units.

Why does the parent unit react

too quickly to other sounds?

The baby unit also picks up other sounds than those of your baby.

Move the sound sources away from the baby unit.

The microphone sensitivity level of the baby unit may be too high.

Decrease the microphone sensitivity level on the parent unit.

Why does the parent unit react

slowly to the baby's crying?

The microphone sensitivity level of the baby unit may be too low.

Increase the microphone sensitivity level on the parent unit.

The ECO Max mode is on and the baby unit only switches on the

DECT signal when the baby makes sounds. Switch off the ECO Max

mode to make the baby unit transmit DECT signals continuously

and to make the parent unit respond more quickly to your baby's

sounds.

Why do the non-rechargeable

batteries of the baby unit run

low quickly? How can I save

battery power?

The microphone sensitivity level of the baby unit may be too high,

which causes the baby unit to transmit more often. Decrease the

microphone sensitivity level in the menu of the parent unit.

The speaker volume on the baby unit may be too high, which

causes the baby unit to consume a lot of energy. Decrease the

speaker volume of the baby unit.

Perhaps you switched on the nightlight. If you want to use the

nightlight, we advise you to run the baby unit on mains power.

To save energy, activate the ECO Max mode.

The specific operating range of

the baby monitor is 330

metres/1000 feet. Why does

my baby monitor manage a

much smaller distance than

that?

The specified range is only valid outdoors in open air.

Why is the operating time of

my parent unit shorter than 24

hours?

When the parent unit is charged for the first 4 times, the operating

time is less than 24 hours. The rechargeable batteries only reach the

full capacity after you charge and discharge them at least 4 times.

14

English

Question Answer

The volume and microphone sensitivity of the parent unit may be

too high, which causes the parent unit to consume a lot of energy.

Decrease the volume and the microphone sensitivity of the parent

unit.

The parent unit may be switched on during charging. Switch off the

parent unit during charging.

What happens during a power

failure?

If the parent unit is sufficiently charged and there are batteries in

the baby unit, the baby monitor continues to operate during a

power failure.

The parent unit switched off

by itself and I can't I switch it

on again. What should I do?

Remove the batteries from the parent unit, reinsert them in the

parent unit, and the parent unit will switch on automatically. You

can also put the small plug in the parent unit and the adapter in the

wall socket, and then the parent unit will switch on automatically.

Why does it take up to 10

hours to charge the parent

unit, even if the batteries are

not completely discharged?

You have removed and then reinserted the batteries. This causes

the parent unit to charge the batteries fully up to 10 hours.

To maintain a long battery lifetime over the years, charging is

slowed down when the batteries are more than 50% charged.

15

English

Dansk

Introduktion

Tillykke med dit køb og velkommen til Philips Avent! For at få fuldt udbytte af den støtte, Philips Avent

tilbyder, skal du registrere dit produkt på www.philips.com/welcome.

Philips Avent sætter en ære i at producere pålidelige produkter, der kan give forældre den tryghed, de

har brug for. Denne Philips Avent-babyalarm hjælper dig døgnet rundt ved at sikre, at du altid kan

høre din baby klart og tydeligt uden forstyrrende støj. DECT-teknologien garanterer nul interferens og

en krystalklar lyd mellem babyenheden og forældreenheden.

Generel beskrivelse (fig. 1)

1 Forældreenhed

2 "Talk"-knap

3 "Sensitivity"-knap (Følsomhed)

4 "Link"-indikator

5 Højttaler

6 Mikrofon

7 Lys, som indikerer lydniveau

8 ECO Max-knap med lys

9 Batteristatusindikator

10 Lydstyrkeknapperne + og -

11 On/off-knap

12 Halsstrop med løkke

13 Batterirum

14 Lille strømstik

15 Låg til batterirum

16 Genopladelige batterier

17 Adapter med lille stik

18 Halsstrop

19 Babyenhed

20 Natlampe

21 Mikrofon

22 PAGE-knap (Søgning)

23 Strømindikator

24 On/off-knap

25 Højttaler

26 Batteristatusindikator

27 Lydstyrke + knap

28 Lydstyrke - knap

29 Vuggevise afspil/stop-knap

30 Næste vuggevise-knap

31 On/off-knap til natlampe

32 Batterirum

33 Lille strømstik

34 Låg til batterirum

35 Ikke-genopladelige 1,5 V R6 AA-batterier (medfølger ikke)

36 Adapter med lille stik

Vigtige sikkerhedsoplysninger

Læs disse vigtige oplysninger omhyggeligt igennem, inden apparatet tages i brug, og gem dem til

eventuel senere brug.

16

Dansk

VIGTIGT

Denne babyalarm er beregnet til at fungere som et hjælpemiddel. Den kan aldrig erstatte ansvarlig

og korrekt forældreopsyn og -overvågning og må ikke bruges sådan.

Lad aldrig det overvågede barn være alene i hjemmet. Sørg altid for, at der er nogen, der kan holde

øje med barnet og tage sig af dets behov.

Ansvarsfraskrivelse

Bemærk, at du bruger denne babyalarm på eget ansvar. Koninklijke Philips N.V. og dets

datterselskaber er ikke ansvarlig for betjeningen af denne babyalarm eller din brug af den og påtager

sig således intet ansvar i forbindelse med din brug af denne babyalarm.

Fare

-

Babyalarmen (eller dele af den) må aldrig kommes ned i vand eller andre væsker. Anbring ikke

apparatet, hvor vand eller anden væske kan dryppe eller sprøjte på det. Babyalarmen må ikke

bruges i fugtige omgivelser eller tæt ved vand.

-

Placer aldrig en genstand oven på babyalarmen, og dæk den ikke til. Ventilationsåbningerne må

ikke blokeres. Installer i overensstemmelse med producentens instruktioner.

-

Ledninger udgør en potentiel risiko for kvælning. Hold ledninger uden for børns rækkevidde (mere

end 1 m væk). Anbring ikke babyalarmen i barnets seng eller kravlegård (fig. 2).

-

Der er fare for eksplosion, hvis engangsbatterier eller genopladelige batterier udskiftes forkert.

Udskift dem kun med batterier af samme type.

Advarsel

-

Kontrollér, om den angivne netspænding på adapteren svarer til den lokale netspænding, før du

slutter strøm til opladeren.

-

Ingen dele af adapteren eller ledningen må ændres eller klippes af, da dette vil føre til farlige

situationer.

-

Brug kun den medfølgende adapter (S003PV0600050-model).

-

Hvis adapteren beskadiges, skal den altid udskiftes med en original adapter af samme type for at

undgå en farlig situation.

-

Dette apparat må bruges af børn fra 8 år og opefter og personer med reducerede fysiske,

sensoriske eller mentale evner eller manglende erfaring og viden, hvis de er blevet instrueret i

sikker brug af apparatet og forstår de medfølgende risici. Lad ikke børn lege med apparatet.

Rengøring og vedligeholdelse må ikke foretages af børn uden opsyn.

-

Sørg for, at lysnetledningen ikke trædes på eller klemmes, navnlig ved stikkene og

stikforbindelserne samt det sted, hvor ledningen føres ud af apparatet.

-

Sørg for at placere babyalarmen, så den tilsluttede ledning ikke spærrer en døråbning eller på

anden måde er i vejen. Hvis du placerer babyalarmen på et bord eller et lavt kabinet, må du aldrig

lade ledningen hænge ud over kanten af bordet eller pladen. Sørg for, at den tilsluttede ledning

ikke ligger på gulvet, hvor den udgør en fare for fald.

-

Hold emballagen (plastikposer, pap, karton osv.) uden for børns rækkevidde. Det er ikke legetøj.

-

For at undgå elektrisk stød må man ikke forsøge at åbne andet end batterirummene i

babyenheden eller i forældreenheden.

Forsigtig

-

Anvend apparatet ved en temperatur mellem 0 °C og 40 °C.

-

Installer ikke apparatet i nærheden af varmekilder, som f.eks. radiatorer, varmeapparater, ovne eller

andre apparater (inkl. forstærkere), der producerer varme.

17

Dansk

-

Sørg for, at dine hænder er tørre, når du håndterer adaptere, stik og lysnetledninger, og når du

udskifter batterier.

-

Alle de nødvendige afmærkninger er placeret på batterirummet i forældreenheden og

babyenheden og i bunden af opladeren (hvis der er nogen).

-

I forældreenheden må der kun benyttes det genopladelige batteri, der leveres sammen med

babyalarmen.

-

Oplad det genopladelige batteri som beskrevet i brugervejledningen.

-

Forældreenheden kan kun oplades ved hjælp af det medfølgende genopladelige batteri.

-

For at undgå batterieksplosion eller -lækage, som kan beskadige babyalarmen og forårsage

forbrændinger og hud- eller øjenirritation, skal du overholde følgende:

-

Ikke-genopladelige batterier må ikke oplades i forældreenheden.

-

Tag de genopladelige batterier og engangsbatterierne ud, hvis du ikke skal bruge babyalarmen i

mere end 30 dage.

-

Sørg for, at batteriernes poler (+ og -) vender den rigtige vej.

-

Hold batterierne væk fra stærk varme, som f.eks. solskin, ild eller lignende.

-

Undlad at lade opbrugte batterier blive siddende i babyenheden.

-

For at forhindre batterierne i at overophede eller afgive giftstoffer, hydrogen eller oxygen må de

ikke overoplades, kortsluttes, oplades omvendt eller beskadiges.

-

Bær beskyttelseshandsker for at beskytte huden, når du håndterer beskadigede eller utætte

batterier.

Overholdelse af standarder

-

Dette apparat overholder EU (fig. 3)'s krav om radiointerferens.

-

Philips Consumer Lifestyle erklærer hermed, at denne babyalarm overholder de væsentlige krav og

andre relevante bestemmelser i direktiv 2014/53/EU (DECT: frekvensbånd 1880-1900 MHz,

maksimal radiofrekvenseffekt: 250 mW). En kopi af EU-overensstemmelseserklæringen (DoC) er

tilgængelig online på www.philips.com/support.

Elektromagnetiske felter (EMF)

Dette Philips-apparat overholder alle branchens gældende standarder og regler angående

eksponering for elektromagnetiske felter.

Klargøring

Babyenhed

Vi anbefaler, at du slutter babyalarmen til lysnettet. For at sikre automatisk strømbackup i tilfælde af

strømsvigt kan du isætte fire 1,5 V AA alkaline-batterier (medfølger ikke).

Brug ikke genopladelige batterier. Babyenheden ikke har nogen ladefunktion, og genopladelige

batterier aflades langsomt, når de ikke benyttes.

1 Tag låget af batterirummet (fig. 4).

2 Isætfire ikke-genopladelige 1,5 V R6 AA-batterier. Sørg for, at + og - polerne vender rigtigt (fig. 5).

3 Sæt låget på igen.

4 Sæt det lille stik ibabyenheden, og sæt adapteren i en stikkontakt (fig. 6).

18

Dansk

Forældreenhed

Forældreenheden benytter to genopladelige 850 mAh Ni-MH-batterier, der leveres sammen med

babyalarmen. Oplad forældreenheden, før du tager den i brug første gang, og når batterierne er

ved at løbe tør.

1 Kontrollér, at forældreenheden er slukket, og at stikket er taget ud af stikkontakten.

2 Tag låget af batterirummet (fig. 7).

3 Sæt de genopladelige batterier i. Sørg for, at + og - polerne vender rigtigt (fig. 8).

4 Sæt låget på igen.

5 Sæt strømadapteren i forældreenheden, og sæt adapteren i en stikkontakt (fig. 9).

Batteristatusindikatoren blinker grønt for at indikere, at apparatet oplades.

Bemærk: Apparatet skal oplades og aflades fire gange, før de genopladelige batterier når først op på

deres fulde kapacitet.

Den normale opladningstid er 10 timer, og den normale brugstid er 24 timer.



Genopladelige batterier:

Producent

Model Klassificering

BYD H-AAA850A-MB20 1,2 V Ni-MH AAA/R03 850 mAh

GPI PH85AAAHC 1,2 V Ni-MH AAA/R03 850 mAh

Adaptere:

UK-modelnummer

S003PB0600050

EU-modelnummer S003PV0600050

Brug af babyalarmen

Placering af babyalarmen

Babyenheden placeres uden for barnets rækkevidde. Anbring ikke babyenheden i barnets seng eller

kravlegård.

Da ledningen til babyenheden udgør en potentiel risiko for kvælning, skal du sørge for, at

babyenheden og dens ledning er mindst 1 meter væk fra barnet. (fig. 10)

For at undgå en skinger tone lyd fra én eller begge enheder, skal du sørge for, at forældreenheden er

mindst 1,5 m væk fra babyenheden.

Bemærk: Hvis forældreenheden kommer uden for babyenhedens rækkevidde, vil forældreenheden

bippe med jævne mellemrum. Link-indikatoren på forældreenheden blinker rødt.

Oprettelse af forbindelse mellem forældre- og babyenhed

1 Tryk på on/off-knappen på babyenheden, og hold den nede i to sekunder (fig. 11).

-

Alle indikatorer på babyenheden lyser kortvarigt.

2 Tryk på on/off-knappen på forældreenheden, og hold den nede i to sekunder (fig. 12).

-

Alle indikatorer på forældreenheden lyser kortvarigt.

-

"Link"-indikatoren blinker rødt, og forældreenheden begynder at søge efter babyenheden.

19

Dansk

-

Når forældreenheden og babyenheden har forbindelse med hinanden, lyser "link"-indikatoren

konstant grønt (fig. 13).

-

Hvis der ikke er etableret forbindelse, blinker "link"-indikatoren rødt, og forældreenheden bipper

en gang imellem.

Bemærk: Det tager mindre end 15 sekunder at etablere forbindelsen mellem forældreenhed og

babyenhed.

Hvad gør man, hvis der ikke oprettes forbindelse

-

Hvis forældreenheden er uden for rækkevidde, skal du placere den tættere på babyenheden, men

ikke tættere end 1 meter.

-

Hvis baby- eller forældreenheden er for tæt på et andet DECT-apparat (f.eks. en trådløs telefon),

skal du slukke for dette eller flytte enheden væk fra apparatet.

-

Hvis babyenheden er slukket, skal du tænde den.

Senderækkevidde

-

Senderækkevidden er 330 meter udendørs og op til 50 meter indendørs.

-

Babyalarmens rækkevidde afhænger af omgivelserne og andre faktorer, der kan forårsage

interferens. Våde og fugtige materialer kan give op til 100 % tab i rækkevidden på grund af

interferens. Interferens forårsaget af tørre materialer fremgår af tabellen nedenfor.

Tørre materialer

Materialets tykkelse Tab af rækkevidde

Træ, gips, pap, glas (uden

metal, ledninger eller bly)

< 30 cm 0-10%

Mursten, krydsfiner < 30 cm 5-35%

Armeret beton < 30 cm 30-100%

Metalgitter eller -stænger < 1 cm 90-100%

Metal- eller

aluminiumsplader

< 1 cm 100%



Funktioner og feedback på babyenheden

Natlampe

Natlampen giver et blødt skær, der beroliger din baby.

1 Tryk på natlampeknappen bag på babyenheden for at tænde natlampen (fig. 14).

2 Tryk på natlampeknappen igen forat slukke natlampen.

Vuggevisefunktion

1 Tryk påvuggevise play/stop-knappen på babyenheden for at afspille den sidst valgte vuggevise

(fig. 15).

Den valgte vuggevise gentages i 30 minutter.

2 Tryk på den næste vuggevise for at vælge en anden vuggevise på listen (fig. 16).

3 Hvis du vil justere lydniveauet for vuggevisen, skal du trykke på + eller – knappen på babyenheden.

4 Vuggevisen kan stoppes ved attrykke på afspil/stop-knappen på babyenheden.

20

Dansk

La page charge ...

Philips SCD506 Manuel utilisateur

Philips SCD506 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents