Kenmore 106.5022 Series Manuel utilisateur

Marque: Kenmore

Modèle: 106.5022 Series

Catégorie: Frigos

Taper: Manuel utilisateur

Ce manuel convient également à

Use & Care Guide

Manual de uso y cuidado

Guide d’utilisation et d’entretien

English / Español / Français

Models/Modelos/Modèles: 106.5022*, 106.5023*, 106.5027*, 106.5028*, 106.5034*, 106.5035*

Kenmore®

Side by Side Refrigerator

Refrigerador de dos puertas

Réfrigérateur côte à côte

* = color number, número de color, numéro de couleur

P/N W10319293B

Sears Brands Management Corporation

Hoffman Estates, IL, U.S.A. 60179

www.kenmore.com

www.sears.com

Sears Canada Inc.

Toronto, Ontario, Canada M5B 2C3

www.sears.ca

TABLE OF CONTENTS

WARRANTY.................................................................................. 4

REFRIGERATOR SAFETY ...............................................................5

Proper Disposal of Your Old Refrigerator......................................... 5

INSTALLATION INSTRUCTIONS .................................................. 6

Unpack the Refrigerator ....................................................................... 6

Location Requirements........................................................................... 6

Electrical Requirements .........................................................................7

Water Supply Requirements ................................................................ 7

Base Grille................................................................................................7

Refrigerator Doors.................................................................................. 8

Adjust the Doors.....................................................................................10

Connect Water Supply.........................................................................10

Prepare the Water System ...................................................................11

Normal Sounds.......................................................................................12

REFRIGERATOR USE ................................................................... 12

Ensuring Proper Air Circulation...........................................................12

Using the Controls .................................................................................12

Convertible Drawer Temperature Control........................................13

Crisper Humidity Control......................................................................13

Chilled Door Bin.....................................................................................13

Water and Ice Dispensers ...................................................................13

Water Filter Status Light......................................................................15

Water Filtration System.......................................................................15

Ice Maker and Storage Bin..................................................................16

REFRIGERATOR FEATURES .........................................................17

Refrigerator Shelves..............................................................................17

Deli Drawer.............................................................................................17

Convertible Vegetable/Meat Drawer, Crisper and Covers..........17

Convertible Vegetable/Meat Drawer Temperature Control ....... 18

Crisper Humidity Control..................................................................... 18

Wine or Can/Bottle Rack ................................................................... 18

Utility Bin................................................................................................. 18

FREEZER FEATURES.....................................................................18

Freezer Shelf.......................................................................................... 19

Freezer Basket or Bin............................................................................ 19

DOOR FEATURES.........................................................................19

Door Bins................................................................................................. 19

Door Rails or Bins.................................................................................. 19

Tilt-out Freezer Door Bin......................................................................20

Chilled Door Bin ....................................................................................20

Tilt-out Fruit Bin .....................................................................................20

REFRIGERATOR CARE.................................................................21

Cleaning...................................................................................................21

Changing the Light Bulbs.....................................................................22

Power Interruptions...............................................................................22

Vacation and Moving Care................................................................23

TROUBLESHOOTING.................................................................. 23

Refrigerator Operation........................................................................23

Temperature and Moisture..................................................................24

Ice and Water.......................................................................................24

PROTECTION AGREEMENTS...................................................... 26

ACCESSORIES............................................................................. 26

WATER FILTER CERTIFICATIONS ............................................... 26

PERFORMANCE DATA SHEET ....................................................27

SERVICE NUMBERS ..................................................BACK COVER

ÍNDICE

GARANTÍA..................................................................................28

SEGURIDAD DEL REFRIGERADOR ............................................. 29

Cómo deshacerse adecuadamente de su refrigerador viejo.......29

INSTRUCCIONES DE INSTALACIÓN.......................................... 30

Desempaque el refrigerador..............................................................30

Requisitos de ubicación.......................................................................30

Requisitos eléctricos ..............................................................................31

Requisitos del suministro de agua ......................................................31

Rejilla de la base...................................................................................31

Puertas del refrigerador......................................................................32

Ajuste las puertas..................................................................................34

Conexión del suministro de agua......................................................34

Preparación del sistema de agua......................................................36

Sonidos normales..................................................................................36

USO DE SU REFRIGERADOR ...................................................... 37

Cómo asegurar la debida circulación del aire...............................37

Uso de los controles .............................................................................37

Control de temperatura del cajón convertible...............................38

Control de humedad del cajón para verduras............................... 38

Depósito enfriador de la puerta........................................................ 38

Despachadores de agua y hielo........................................................38

Luz de estado del filtro de agua.......................................................39

Sistema de filtración de agua............................................................40

Fábrica de hielo y depósito.................................................................41

CARACTERÍSTICAS DEL REFRIGERADOR ...................................41

Estantes del refrigerador.....................................................................42

Cajón para carnes frías.......................................................................42

Cajón convertible para verduras/carne,

cajón para verduras y tapas..............................................................42

Control de temperatura para el cajón

convertible de verduras/carnes.........................................................42

Control de humedad del cajón para verduras ...............................43

Portavinos o portabotellas/latas .......................................................43

Recipiente utilitario...............................................................................43

CARACTERÍSTICAS DEL CONGELADOR.....................................43

Estante del congelador....................................................................... 44

Canastilla o recipiente del congelador ........................................... 44

CARACTERÍSTICAS DE LA PUERTA ........................................... 44

Recipientes de la puerta..................................................................... 44

Rieles o recipientes de la puerta........................................................45

Depósito inclinable de la puerta del congelador...........................45

Depósito enfriador de la puerta........................................................45

Recipiente inclinable para frutas...................................................... 46

CUIDADO DE SU REFRIGERADOR .............................................46

Limpieza ................................................................................................ 46

Cómo cambiar los focos .................................................................... 47

Cortes de corriente.............................................................................. 48

Cuidado durante las vacaciones y mudanzas ............................... 48

SOLUCIÓN DE PROBLEMAS .......................................................49

Funcionamiento del refrigerador...................................................... 49

Temperatura y humedad.....................................................................50

Hielo y agua ..........................................................................................50

CONTRATOS DE PROTECCIÓN.................................................. 52

ACCESORIOS.............................................................................. 52

HOJA DE DATOS DEL RENDIMIENTO........................................ 53

NÚMEROS DE SERVICIO .................................CONTRAPORTADA

TABLE DES MATIÈRES

GARANTIE ................................................................................. 54

SÉCURITÉ DU RÉFRIGÉRATEUR...................................................55

Mise au rebut de votre vieux réfrigérateur ..................................... 55

INSTRUCTIONS D’INSTALLATION..............................................56

Déballage du réfrigérateur ................................................................56

Exigences d'emplacement ..................................................................56

Spécifications électriques....................................................................57

Spécifications de l’alimentation en eau ...........................................57

Grille de la base...................................................................................57

Portes du réfrigérateur.........................................................................58

Ajustement des portes..........................................................................60

Raccordement de la canalisation d'eau ..........................................60

Préparer le système d'eau...................................................................62

Sons normaux........................................................................................62

UTILISATION DU RÉFRIGÉRATEUR............................................ 63

Pour s’assurer d’une circulation d’air appropriée...........................63

Utilisation des commandes.................................................................63

Commande de température du tiroir convertible ..........................64

Réglage de l'humidité dans le bac à légumes................................64

Compartiment froid de la porte........................................................64

Distributeurs d’eau et de glaçons ......................................................64

Témoin lumineux de l’état du filtre à eau........................................65

Système de filtration d’eau.................................................................66

Machine à glaçons et bac d'entreposage.......................................67

CARACTÉRISTIQUES DU RÉFRIGÉRATEUR ................................ 68

Tablettes du réfrigérateur...................................................................68

Tiroir pour spécialités alimentaires....................................................68

Tiroir à légumes/viande convertible,

bac à légumes et couvercles..............................................................68

Réglage de la température du tiroir à

légumes/viande convertible ...............................................................69

Réglage de l’humidité dans le bac à légumes................................69

Casier à vin ou porte-cannettes/bouteilles......................................69

Casier utilitaire ......................................................................................69

CARACTÉRISTIQUES DU CONGÉLATEUR ..................................69

Tablette de congélateur..................................................................... 70

Panier ou bac de congélateur........................................................... 70

CARACTÉRISTIQUES DE LA PORTE ............................................70

Balconnets dans la porte.................................................................... 70

Tringles ou balconnets dans la porte................................................ 71

Compartiment inclinable de la porte du congélateur................... 71

Compartiment fraîcheur ...................................................................... 71

Bac à fruits inclinable.......................................................................... 72

ENTRETIEN DU RÉFRIGÉRATEUR ...............................................72

Nettoyage ............................................................................................. 72

Remplacement des ampoules d’éclairage...................................... 73

Pannes de courant ...............................................................................74

Entretien avant les vacances ou lors d’un déménagement.......... 74

DÉPANNAGE.............................................................................. 75

Fonctionnement du réfrigérateur ...................................................... 75

Température et humidité .................................................................... 76

Glaçons et eau..................................................................................... 76

CONTRATS DE PROTECTION.....................................................78

ACCESSOIRES.............................................................................78

FEUILLE DE DONNÉES SUR LA PERFORMANCE.........................79

NUMÉROS DE SERVICE ............................ COUVERTURE ARRIÈRE

KENMORE APPLIANCE WARRANTY

ONE YEAR LIMITED WARRANTY

When installed, operated and maintained according to all

instructions supplied with the product, if this appliance fails due to

a defect in material or workmanship within one year from the date

of purchase, call 1!800!4!MY!HOME

to arrange for free repair.

This warranty applies for only 90 days from the date of purchase if

this appliance is ever used for other than private family purposes.

THIS WARRANTY COVERS ONLY DEFECTS IN MATERIAL AND

WORKMANSHIP. SEARS WILL NOT PAY FOR:

1. Expendable items that can wear out from normal use, including

but not limited to filters, belts, light bulbs, and bags.

2. A service technician to instruct the user in correct product

installation, operation or maintenance.

3. A service technician to clean or maintain this product.

4. Damage to or failure of this product if it is not installed,

operated or maintained according to all instructions supplied

with the product.

5. Damage to or failure of this product resulting from accident,

abuse, misuse or use for other than its intended purpose.

6. Damage to or failure of this product caused by the use of

detergents, cleaners, chemicals or utensils other than those

recommended in all instructions supplied with the product.

7. Damage to or failure of parts or systems resulting from

unauthorized modifications made to this product.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF

REMEDIES

Customer’s sole and exclusive remedy under this limited warranty

shall be product repair as provided herein. Implied warranties,

including warranties of merchantability or fitness for a particular

purpose, are limited to one year or the shortest period allowed by

law. Sears shall not be liable for incidental or consequential

damages. Some states and provinces do not allow the exclusion or

limitation of incidental or consequential damages, or limitations on

the duration of implied warranties of merchantability or fitness, so

these exclusions or limitations may not apply to you.

This warranty applies only while this appliance is used in the United

States or Canada.

This warranty gives you specific legal rights, and you may also

have other rights which vary from state to state.

Sears Brands Management Corporation

Hoffman Estates, IL 60179

Sears Canada Inc.

Toronto, Ontario, Canada M5B 2C3

PRODUCT RECORD

Record your complete model number, serial number, and purchase

date. You can find this information on the model and serial number

label located on the product.

Have this information available to help you obtain assistance or

service more quickly whenever you contact Sears concerning your

appliance.

Model number __ __ __._____________________________________

Serial number _____________________________________________

Purchase date _____________________________________________

Save these instructions and your sales receipt for future reference.

REFRIGERATOR SAFETY

Proper Disposal of Your Old Refrigerator

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still dangerous –

even if they will sit for “just a few days.” If you are getting rid of

your old refrigerator, please follow these instructions to help

prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

■ Take off the doors.

■ Leave the shelves in place so that children may not easily climb

inside.

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

IMPORTANT SAFETY INSTRUCTIONS

WARNING:

To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

SAVE THESE INSTRUCTIONS

■

Plug into a grounded 3 prong outlet.

■

Do not remove ground prong.

■

Do not use an adapter.

■

Do not use an extension cord.

■

Disconnect power before servicing.

■

Replace all parts and panels before operating.

■

Remove doors from your old refrigerator.

■

Use nonflammable cleaner.

■

Keep flammable materials and vapors, such as gasoline,

away from refrigerator.

■

Use two or more people to move and install refrigerator.

■

Disconnect power before installing ice maker (on ice maker

kit ready models only).

■

Use a sturdy glass when dispensing ice (on some models).

■

Do not hit the refrigerator glass doors (on some models).

WARNING

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

INSTALLATION INSTRUCTIONS

Unpack the Refrigerator

Remove the Packaging

■ Remove tape and glue residue from surfaces before turning on

the refrigerator. Rub a small amount of liquid dish soap over

the adhesive with your fingers. Wipe with warm water and dry.

■ Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator. For more

information see “Refrigerator Safety.”

Clean Before Using

After you remove all of the packaging materials, clean the inside of

your refrigerator before using it. See the cleaning instructions in

“Refrigerator Care.”

Location Requirements

To ensure proper ventilation for your refrigerator, allow for ¹⁄₂"

(1.25 cm) of space on each side and at the top. Allow for 1"

(2.54 cm) of space behind the refrigerator. If your refrigerator has

an ice maker, allow extra space at the back for the water line

connections. When installing your refrigerator next to a fixed wall,

leave a 2" (5.08 cm) minimum space on each side (depending on

your model) to allow the doors to swing open.

NOTES:

■ It is recommended that you do not install the refrigerator near

an oven, radiator, or other heat source. Do not install in a

location where the temperature will fall below 55°F (13°C).

■ Normal minimum cabinet cut-out width required for product

installation is 36" (91.44 cm). However, if the product is placed

against an extended wall and the ability to remove the crisper

pans is desired, an additional 18" (45.72 cm) of cabinet width

is required, so a total cabinet opening width of 54" (137.16 cm)

is recommended.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for

cleaning or service, be sure to cover the floor with

cardboard or hardboard to avoid floor damage. Always pull

the refrigerator straight out when moving it. Do not wiggle or

“walk” the refrigerator when trying to move it, as floor

damage could occur.

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers

are heavy. Use both hands when removing them to avoid

dropping.

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

2" (1.25 cm)

2" (5.08 cm)

Electrical Requirements

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only, 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet that

cannot be turned off by a switch. Do not use an extension cord.

NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn the control (Thermostat, Refrigerator or

Freezer Control depending on the model) to OFF and then

disconnect the refrigerator from the electrical source. When you

are finished, reconnect the refrigerator to the electrical source and

reset the control (Thermostat, Refrigerator or Freezer Control

depending on the model) to the desired setting. See “Using the

Controls.”

Water Supply Requirements

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed here.

TOOLS NEEDED:

NOTE: Your refrigerator dealer has a kit available with a

¹⁄₄"

(6.35 mm) saddle-type shutoff valve, a union, and copper tubing.

Before purchasing, make sure a saddle-type valve complies with

your local plumbing codes. Do not use a piercing-type or

³⁄₁₆"

(4.76 mm) saddle valve which reduces water flow and clogs more

easily.

IMPORTANT:

■ All installations must meet local plumbing code requirements.

■ Use copper tubing and check for leaks. Install copper tubing

only in areas where the household temperatures will remain

above freezing.

Water Pressure

A cold water supply with water pressure of between 30 and 120 psi

(207 and 827 kPa) is required to operate the water dispenser and

ice maker. If you have questions about your water pressure, call a

licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the

refrigerator needs to be between 30 and 120 psi (207 and

827 kPa).

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis system

needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than 40 to

60 psi (276 to 414 kPa):

■ Check to see whether the sediment filter in the reverse osmosis

system is blocked. Replace the filter if necessary.

■ Allow the storage tank on the reverse osmosis system to refill

after heavy usage.

■ If your refrigerator has a water filter, it may further reduce the

water pressure when used in conjunction with a reverse osmosis

system. Remove the water filter. See “Water Filtration System.”

If you have questions about your water pressure, call a licensed,

qualified plumber.

Base Grille

Remove the Base Grille:

1. Open both doors.

2. Place hands along the ends of the grille. Push in on the top of

the base grille and pull up on the bottom.

NOTE: Be sure to refasten the Tech Sheet behind the base grille

after cleaning.

Replace the Base Grille:

1. Open both doors.

2. Line up the grille support tabs with the metal clips.

3. Push the grille firmly to snap it into place.

■ Flat-blade screwdriver

■ ⁷⁄₁₆" and ¹⁄₂" Open-end or two

adjustable wrenches

■ ¹⁄₄" Nut driver

■ ¹⁄₄" Drill bit

■ Cordless drill

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Refrigerator Doors

TOOLS NEEDED: ¹⁄₄" hex-head socket wrench, ⁵⁄₁₆" hex-head socket wrench and a flat-blade screwdriver.

IMPORTANT: Before you begin, turn the refrigerator control OFF. Unplug refrigerator or disconnect power. Remove food and any adjustable

door or utility bins from doors.

NOTE: It may only be necessary to remove either the door handle or the doors to get your product through the doorway of your home.

Measure the doorway to see whether you need to remove the refrigerator handles or the doors.

WARNING

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

Door Removal

Base Grille

Top Left Hinge

A. Do Not Remove Screw

Handle

Removal

(Optional)

Bottom Hinge

A. Do Not

Remove Screw

Water Dispenser

Tubing Connection

A. Red Outer Ring

A. Do Not Remove Screw

Top Right Hinge

Door Alignment

Level

Door Closing and Alignment

Front Leveling

A. Leveling Screw

Remove the Handles (optional)

1. Apply firm pressure with your hand on the face of trim. Slide

top trim up and bottom trim down away from handle. Lift trim

pieces off shoulder screws. See Graphic 1.

2. Remove handle screws and handles. See Graphic 1.

3. Move refrigerator into place. Replace handles as shown. See

Graphic 1.

Remove the Doors

1. Unplug refrigerator or disconnect power.

2. Open both refrigerator doors. Remove the base grille. Place

hands along the ends of the grille. Push in on the top of the

base grille and pull up on the bottom. See Graphic 2.

3. Close both doors and keep them closed until you are ready to

lift them free from the cabinet.

4. If you have a dispenser (ice or water), disconnect the water

dispenser tubing located behind the base grille on the freezer

door side. The dispenser tubing runs through the door hinge,

and must be disconnected in order to remove the door. See

Graphic 3.

■ Press the red outer ring against the face of the fitting and

pull the dispenser tubing free.

■ On some models, remove the tubing from hose clip.

5. Remove the top left hinge cover and screws as shown. See

Graphic 4. Do not remove screw A.

6. Disconnect wiring:

■ Disconnect wiring plug.

■ Remove green ground wire screw to disconnect ground

wires.

7. Lift freezer door straight up and off of the bottom hinge. See

Graphic 5. The water dispenser tubing remains attached to the

freezer door and pulls through the bottom left hinge. Be sure to

avoid damaging the dispenser tubing.

8. Remove the top right hinge cover and screws as shown. See

Graphic 6. Do not remove screw A.

9. Lift the refrigerator door straight up and off of the bottom

hinge.

10. It may not be necessary to remove the bottom hinge to move

the refrigerator through a doorway. Both bottom hinges have

similar construction.

■ Remove the hinges as shown. See Graphic 7. Do not

remove screw A.

Replace the Doors and Hinges

1. Replace both bottom hinges, if removed. Tighten screws.

2. Feed the dispenser tubing through the bottom left hinge before

replacing the freezer door on the hinge. Assistance may be

needed.

NOTE: Provide additional support for the doors while the top

hinges are being replaced. Do not depend on the door magnets

to hold the doors in place while you are working.

3. Reconnect water dispenser tubing by pushing tubing into fitting

until it stops and the red outer ring touches face of fitting. See

Graphic 3. On some models, replace tubing in hose clip.

4. Align and replace the top left hinge as shown. See Graphic 4.

Tighten screws.

■ Reconnect both ground wires.

■ Reconnect wiring plug.

5. Replace left hinge cover and screws.

6. Replace the refrigerator door by lifting the door onto the

bottom right hinge.

7. Align and replace the top right hinge as shown. See Graphic 6.

Tighten screws.

8. Replace hinge cover and screws. Tighten screws.

9. Plug in refrigerator or reconnect power.

A. Do not remove screw A.

B. Ground wires

C. Green ground wire screw

D. Wiring plug

WARNING

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

A. Do not remove screw A.

B. Ground wires

C. Green ground wire screw

D. Wiring plug

WARNING

Electrical Shock Hazard

Reconnect both ground wires.

Failure to do so can result in death or electrical shock.

Adjust the Doors

Door Closing

1. Place a level inside the refrigerator at the back of the top shelf.

See Graphic 8 in “Refrigerator Doors.”

2. Locate the leveling screws behind the base grille of the

refrigerator on either side.

3. Use a hex-head wrench to adjust the front roller leveling screws

until the refrigerator is level. Turn the front roller leveling screw

to the right to raise that side of the refrigerator or turn the

leveling screw to the left to lower that side. See Graphic 10 in

“Refrigerator Doors.” Make sure refrigerator is level before

proceeding.

4. Check the door alignment after leveling the refrigerator.

Align the Doors

IMPORTANT: First level the back of the refrigerator as described in

“Door Closing.”

The doors may be uneven after leveling the refrigerator. See

Graphic 9 in “Refrigerator Doors.” The doors are preset at the

factory so that the refrigerator door is higher than the freezer door

by approximately the thickness of a quarter. Once the doors are

loaded with food, they should be even. If the door height needs to

be adjusted AFTER the doors have been loaded with food, follow

the these steps.

1. Use a hex-head wrench to adjust the front roller leveling screws

until the doors are even. Turn the front roller leveling screw to

the right to raise that side of the refrigerator or turn the leveling

screw to the left to lower that side. See Graphic 10 in

“Refrigerator Doors.”

NOTE: Open and close both the refrigerator and freezer doors

after each adjustment to check the door alignment.

2. Open the doors and replace the base grille. Line up the grille

support tabs with the metal clips. Push the grille firmly to snap it

into place.

NOTE: Be sure to refasten the Tech Sheet behind the base

grille.

Connect Water Supply

Read all directions before you begin.

IMPORTANT: If you turn the refrigerator on before the water line is

connected, turn the ice maker OFF.

Connect to Water Line

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Locate a

¹⁄₂" (1.27 cm) to 1¹⁄₄" (3.18 cm) vertical cold water pipe

near the refrigerator.

IMPORTANT:

■ Make sure it is a cold water pipe.

■ Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from

the drill and normal sediment from collecting in the valve.

4. Determine the length of copper tubing you need. Measure from

the connection on the lower rear corner of refrigerator to the

water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use

¹⁄₄"

(6.35 mm) O.D. (outside diameter) copper tubing. Be sure both

ends of copper tubing are cut square.

5. Using a cordless drill, drill a

¹⁄₄" (6.35 mm) hole in the cold

water pipe you have selected.

6. Fasten the shutoff valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the

¹⁄₄" (6.35 mm)

drilled hole in the water pipe and that the washer is under the

pipe clamp. Tighten the packing nut. Tighten the pipe clamp

screws slowly and evenly so the washer makes a watertight

seal. Do not overtighten, or you may crush the copper tubing.

7. Slip the compression sleeve and compression nut on the copper

tubing as shown. Insert the end of the tubing into the outlet end

squarely as far as it will go. Screw the compression nut onto

outlet end with adjustable wrench. Do not overtighten.

8. Place the free end of the tubing in a container or sink, and turn

ON the main water supply. Flush the tubing until water is clear.

Turn OFF the shutoff valve on the water pipe. Coil the copper

tubing.

Connect to Refrigerator

Style 1

1. Unplug refrigerator or disconnect power.

2. Remove and discard the plastic part that is attached to the

inlet of the water valve.

3. Attach the copper tube to the valve inlet using a compression

nut and sleeve as shown. Tighten the compression nut. Do not

overtighten.

4. Use the tube clamp on the back of the refrigerator to secure

the tubing to the refrigerator as shown. This will help avoid

damage to the tubing when the refrigerator is pushed back

against the wall.

5. Turn shutoff valve ON.

6. Check for leaks. Tighten any connections (including connections

at the valve) or nuts that leak.

A. Cold water pipe

B. Pipe clamp

C. Copper tubing

D. Compression nut

E. Compression sleeve

F. Shutoff valve

G. Packing nut

A. Tube clamp

B. Tube clamp screw

C. Copper tubing

D. Compression nut

E. Valve inlet

DEF

7. The ice maker is equipped with a built-in water strainer. If your

water conditions require a second water strainer, install it in the

¹⁄₄" (6.35 mm) water line at either tube connection. Obtain a

water strainer from your nearest appliance dealer.

Style 2

1. Unplug refrigerator or disconnect power.

2. Remove and discard the black nylon plug from the gray water

tube on the rear of the refrigerator.

3. If the gray water tube supplied with the refrigerator is not long

enough, a

¹⁄₄" x ¹⁄₄" (6.35 mm x 6.35 mm) coupling is needed in

order to connect the water tubing to an existing household

water line. Thread the provided nut onto the coupling on the

end of the copper tubing.

NOTE: Tighten the nut by hand. Then tighten it with a wrench

two more turns. Do not overtighten.

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any nuts or connections (including

connections at the valve) that leak.

Style 3

1. Unplug refrigerator or disconnect power.

2. Remove and discard the cap from the gray water tube.

3. Using a compression nut and sleeve, attach the copper tube to

the water inlet.

4. Once secured, tighten the compression nut. Do not overtighten.

5. Check the connection by pulling on the copper tubing. Turn on

water supply to refrigerator. Check for leaks. Tighten any nuts

or connections that leak.

Complete the Installation

1. Plug into a grounded 3 prong outlet.

2. Flush the water system. See “Prepare the Water System” or

“Water and Ice Dispensers.”

NOTE: Allow 24 hours to produce the first batch of ice. Allow

3 days to completely fill ice container.

Prepare the Water System

Please read before using the water system.

Immediately after installation, follow the steps below to make sure

that the water system is properly cleaned.

1. Open the freezer door and turn off the ice maker.

For Style 1, lift up the wire shutoff arm as shown.

For Style 2, move the switch to the OFF (right) setting as shown.

The On/Off switch is located on the top right side of the

freezer compartment.

NOTE: If your model has a base grille filter system, make sure the

base grille filter is properly installed and the cartridge cap handle

is in the horizontal position.

A. Refrigerator water tubing

B. Nut (provided)

C. Bulb

D. Coupling (purchased)

E. Ferrule (purchased)

F. Nut (purchas ed)

G. Household water line

A. Cap

B. Inlet

A B C D E F G

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction

may be used on disinfected waters that may contain

filterable cysts.

2. Flush the water system. Use a sturdy container to depress and

hold the water dispenser lever for 5 seconds, then release it for

5 seconds. Repeat until water begins to flow. Once water

begins to flow, continue depressing and releasing the dispenser

lever (5 seconds on, 5 seconds off) until a total of 3 gal. (12 L)

has been dispensed. This will flush air from the filter and water

dispensing system, and prepare the water filter for use.

Additional flushing may be required in some households. As air

is cleared from the system, water may spurt out of the

dispenser.

3. Open the freezer door and turn on the ice maker. For Style 1,

lower the wire shutoff arm. For Style 2, move the switch to the

ON (left) position. Please refer to the “Ice Maker and Storage

Bin” section for further instructions on the operation of your ice

maker.

■ Allow 24 hours to produce the first batch of ice.

■ Discard the first three batches of ice produced.

■ Depending on your model, you may want to select the

maximum ice feature to increase the production of ice.

Normal Sounds

Your new refrigerator may make sounds that your old one didn’t

make. Because the sounds are new to you, you might be concerned

about them. Most of the new sounds are normal. Hard surfaces,

such as the floor, walls, and cabinets, can make the sounds seem

louder. The following describes the kinds of sounds and what may

be making them.

■ If your refrigerator is equipped with an ice maker, you will hear

a buzzing sound when the water valve opens to fill the ice

maker for each cycle.

■ Your refrigerator is designed to run more efficiently to keep

your food items at the desired temperatures and to minimize

energy usage. The high efficiency compressor and fans may

cause your refrigerator to run longer than your old one. You

may also hear a pulsating or high-pitched sound from the

compressor or fans adjusting to optimize performance.

■ You may hear the evaporator fan motor circulating air through

the refrigerator and freezer compartments. The fan speed may

increase as you open the doors or add warm food.

■ Rattling noises may come from the flow of refrigerant, the

water line, or items stored on top of the refrigerator.

■ Water dripping on the defrost heater during a defrost cycle

may cause a sizzling sound.

■ As each cycle ends, you may hear a gurgling sound due to the

refrigerant flowing in your refrigerator.

■ Contraction and expansion of the inside walls may cause a

popping noise.

■ You may hear air being forced over the condenser by the

condenser fan.

■ You may hear water running into the drain pan during the

defrost cycle.

REFRIGERATOR USE

Ensuring Proper Air Circulation

In order to ensure proper temperatures, you need to permit air to

flow between the two sections. Cold air enters the bottom of the

freezer section and moves up. It then enters the refrigerator section

through the top vent. Air then returns to the freezer as shown.

Do not block any airflow vents. If the vents are blocked, airflow will

be obstructed and temperature and moisture problems may occur.

IMPORTANT: Because air circulates between both sections, any

odors formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To avoid odor

transfer and drying out of food, wrap or cover foods tightly.

Using the Controls

For your convenience, your refrigerator controls are preset at the

factory. When you first install your refrigerator, make sure that the

controls are still preset. The Refrigerator Control and the Freezer

Control should both be set to the “mid-settings.”

Style 1: Rotary Controls

Style 2: Slide Controls

IMPORTANT:

■ Your product will not cool when the REFRIGERATOR Control is

set to OFF.

■ The Refrigerator Control adjusts the refrigerator compartment

temperature. The Freezer Control adjusts the freezer

compartment temperature. Settings to the left of the

mid!setting make the temperature less cold. Settings to the

right of the mid!setting make the temperature colder.

Refrigerator

off

colder

234

Freezer

cold

colder

234

■ Wait 24 hours before you put food into the refrigerator. If you

add food before the refrigerator has cooled completely, your

food may spoil.

NOTE: Adjusting the Refrigerator and Freezer Controls to a higher

(colder) than recommended setting will not cool the compartments

any faster.

Adjusting Controls

Give the refrigerator time to cool down completely before adding

food. It is best to wait 24 hours before you put food into the

refrigerator. The settings indicated in the previous section should be

correct for normal household refrigerator usage. The controls are

set correctly when milk or juice is as cold as you like and when ice

cream is firm.

Rotary Controls: Turn the control right (clockwise) to make the

compartment colder. Turn the control left (counterclockwise) to

make it less cold. To turn the cooling system off, turn the

Refrigerator Control counterclockwise until it reaches the OFF

position.

Slide Controls: Slide the control one setting to the right to make the

compartment colder. Slide the control one setting to the left to

make it less cold.

If you need to adjust temperatures in the refrigerator or freezer, use

the settings listed in the chart below as a guide. Wait at least

24 hours between adjustments.

Convertible Drawer Temperature Control

(on some models)

The control can be adjusted to properly chill meats or vegetables.

The air inside the pan is cooled to avoid “spot” freezing and can be

set to keep meats at the National Livestock and Meat Board

recommended storage temperatures of 28° to 32°F (!2° to 0°C).

To store meat:

Set the control to one of the three MEAT settings to store meat at its

optimal storage temperature.

To store vegetables:

Set the control to VEG to store vegetables at their optimal storage

temperatures.

NOTE: If food starts to freeze, move the control to the right (less

cold), toward the VEG setting. Remember to wait 24 hours

between adjustments.

Crisper Humidity Control

(on some models)

You can control the amount of humidity in the moisture-sealed

crisper. Adjust the control to any setting between LOW and HIGH.

LOW (open) for best storage of fruits and vegetables with skins.

HIGH (closed) for best storage of fresh, leafy vegetables.

Chilled Door Bin

(on some models)

Cool air from the freezer is directed to the refrigerator door bin

directly beneath the vents.

NOTE: The dairy compartment and can rack are not associated

with the Chilled Door Bin feature.

Chilled Door Bin Control

The chilled door bin control is located on the left-hand side of the

refrigerator compartment.

■ Slide the door chill control to the left to reduce the flow of cold

air to the bin and make it less cold.

■ Slide the door chill control to the right to increase the flow of

cold air to the bin and make it colder.

Water and Ice Dispensers

(on some models)

Depending on your model, you may have one or more of the

following options: the ability to select either crushed or cubed ice, a

special light that turns on when you use the dispenser, or a lock

option to avoid unintentional dispensing.

IMPORTANT: After connecting the refrigerator to a water source or

replacing the water filter, flush the water system. Use a sturdy

container to depress and hold the water dispenser lever for

5 seconds, then release it for 5 seconds. Repeat until water begins

to flow. Once water begins to flow, continue depressing and

releasing the dispenser lever (5 seconds on, 5 seconds off) until a

total of 3 gal. (12 L) has been dispensed. This will flush air from the

filter and water dispensing system, and prepare the water filter for

use. Additional flushing may be required in some households. As air

is cleared from the system, water may spurt out of the dispenser.

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR too warm REFRIGERATOR Control

one setting higher

FREEZER too warm/

too little ice

FREEZER Control

one setting higher

REFRIGERATOR too cold REFRIGERATOR Control

one setting lower

FREEZER too cold FREEZER Control

one setting lower

A. Chilled door bin control

The Water Dispenser

Allow 24 hours for the refrigerator to cool down and chill water.

NOTE: Water may have an off-flavor if you do not use the

dispenser periodically. Dispense at least 1 qt (1 L) of water every

week to maintain a fresh supply.

To Dispense Water:

1. Press a sturdy glass against the water dispenser lever.

2. Remove the glass to stop dispensing.

IMPORTANT: Depending on your model, the small removable tray

at the bottom of the dispenser is designed to catch small spills and

allow for easy cleaning. There is no drain in the tray. The tray can

be removed from the dispenser and carried to the sink to be

emptied or cleaned.

The Ice Dispenser

Ice dispenses from the ice maker storage bin in the freezer. When

the dispenser lever is pressed:

■ A trap door opens in a chute between the dispenser and the ice

bin. Ice moves from the bin and falls through the chute.

■ When you release the dispenser lever, the trap door closes and

the ice dispensing stops. The dispensing system will not operate

when the freezer door is open.

Some models dispense both cubed and crushed ice. Before

dispensing ice, select which type of ice you prefer. The button

controls are designed for easy use and cleaning.

For crushed ice, cubes are crushed before they are dispensed. This

may cause a slight delay when dispensing crushed ice. Noise from

the ice crusher is normal, and pieces of ice may vary in size. When

changing from crushed to cubed, a few ounces of crushed ice will

be dispensed along with the first cubes.

To Dispense Ice:

1. Press button for the desired type of ice.

2. Press a sturdy glass against the ice dispenser lever. Hold the

glass close to the dispenser opening so ice does not fall outside

of the glass.

IMPORTANT: You do not need to apply a lot of pressure to the

lever in order to activate the ice dispenser. Pressing hard will

not make the ice dispense faster or in greater quantities.

3. Remove the glass to stop dispensing.

NOTE: The first few batches of ice may have an off-flavor from

new plumbing and parts. Throw the ice away. Also, take large

amounts of ice from the ice bin, not through the dispenser.

The Dispenser Light (on some models)

The dispenser area has a light. It can be turned on manually by

pressing the ON button (touchpad or rocker switch).

On some models: Whenever you use the dispenser, the lever will

automatically turn the light on.

NOTE: See “Changing the Light Bulbs” for information on changing

the dispenser light bulb.

The Dispenser Lock (on some models)

The dispenser can be turned off for easy cleaning or to avoid

unintentional dispensing by small children and pets.

NOTE: The lock feature does not shut off power to the refrigerator,

to the ice maker, or to the dispenser light. It simply deactivates the

dispenser levers.

■ To turn off the dispenser, press the LOCK button. The indicator

will appear above the LOCK button and the ice and water

dispensers will not work.

■ To unlock the dispenser, press the UNLOCK button until the

indicator appears. Then continue to dispense ice or water as

usual.

ICE

CRUSH CUBE

Cut Hazard

Use a sturdy glass when dispensing ice.

Failure to do so can result in cuts.

WARNING

LIGHT

OFF ON

DISPENSER

LOCK

UNLOCK

Water Filter Status Light

(on some models)

The water filter status light will help you know when to change your

water filter.

■ When the status light changes from green to yellow, this tells

you that it is almost time to change the water filter.

■ It is recommended that you replace the filter when the status

light changes to red OR when water flow to your water

dispenser or ice maker decreases noticeably.

The filter should be replaced at least every 6 months depending on

your water quality and usage. To change the filter, see “Water

Filtration System.”

After changing the water filter, reset the status light by pressing

and holding the RESET button for 2 seconds. The status light will

change from Replace (red) to Good (green) when the system is

reset.

Water Filtration System

Changing the Water Filter

The water filter is located in the base grille below the freezer

compartment door. It is not necessary to remove the base grille to

remove the filter.

1. Remove the filter by pressing the eject button and pulling

straight out on the filter cap.

NOTES:

■ Avoid twisting the cap when removing the filter because

this could cause the cap to come off. If this occurs, replace

the cap and pull the filter straight out.

■ There will be water in the filter. Some spilling may occur.

2. Remove the cap by turning it counterclockwise until it stops.

IMPORTANT: Do not discard the cap. It is part of your

refrigerator. Keep the cap to use with the replacement filter.

3. Take the new cartridge out of its packaging and remove the

covers from O-rings.

4. Place the cap (removed in Step 2) on the new filter. Align the

ridge on the cap with the arrow on the filter. Turn the cap

clockwise until it snaps into place.

5. Push the new filter into the opening in the base grille. As the

filter is inserted, the eject button will depress. The eject button

will pop back out when the filter is fully engaged.

6. Pull gently on the cap to check that the filter is securely in

place.

7. Flush the water system. See “Water and Ice Dispensers.”

INDICATOR: STATUS:

GOOD (green) New filter installed

ORDER (yellow) Order filter

REPLACE (red) OR

when water flow decreases

Replace water filter

Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction

may be used on disinfected waters that may contain

filterable cysts.

A. Eject button

B. Filter cap

A. Cover

B. O-ring

A. Eject button

B. Arrow on filter

C. Ridge on cap

Using the Dispenser Without the Water Filter Cartridge

You can run the dispenser without a water filter cartridge. Your

water will not be filtered.

1. Remove the filter by pressing the eject button and pulling on

the cap. See “Changing the Water Filter” earlier in this section.

2. Remove the cap by turning it counterclockwise until it stops.

IMPORTANT: Do not discard the cap. It is part of your

refrigerator. Keep the cap to use with the replacement filter.

3. With the cap in a horizontal position, insert the cap into the

base grille until it stops.

4. Turn the cap counterclockwise until the cap slips into the

attachment slot. Then, turn the cap clockwise until it is in a

horizontal position.

NOTE: The cap will not be even with the base grille.

Ice Maker and Storage Bin

(on some models)

■ Allow 24 hours to produce the first batch of ice. Discard the

first three batches of ice produced.

■ The quality of your ice will be only as good as the quality of the

water supplied to your ice maker. Avoid connecting the ice

maker to a softened water supply. Water softener chemicals

(such as salt) can damage parts of the ice maker and lead to

poor quality ice. If a softened water supply cannot be avoided,

make sure the water softener is operating properly and is well

maintained.

■ Do not use anything sharp to break up the ice in the storage

bin. This can cause damage to the ice container and the

dispenser mechanism.

■ Do not store anything on top of or in the ice maker or storage

bin.

Style 1

Turning the Ice Maker On/Off:

The On/Off switch is located on the top right-hand side of the

freezer compartment.

■ To turn on the ice maker, slide the control to the ON (left)

position.

■ To manually turn off the ice maker, slide the control to the OFF

(right) position.

NOTE: Your ice maker has an automatic shutoff. The ice maker

sensors will automatically stop ice production, but the control will

remain in the ON (left) position.

Removing and Replacing Ice Storage Bin:

1. Hold the base of the storage bin with both hands and press the

release button to lift the storage bin up and out.

NOTE: It is not necessary to turn the ice maker control to the

OFF (right) position when removing the storage bin. The sensor

cover (“flipper door”) on the left wall of the freezer stops the

ice maker from producing ice if the door is open or the storage

bin is removed.

2. Replace the storage bin on the door and push down to make

sure it is securely in place.

Style 2

Turning the Ice Maker On/Off:

■ To turn ON the ice maker, simply lower the wire shutoff arm.

■ To manually turn off the ice maker, lift the wire shutoff arm to

the OFF (arm up) position and listen for the click. Ice can still

be dispensed, but no more can be made.

NOTE: Your ice maker has an automatic shutoff. As ice is made, the

ice cubes will fill the ice storage bin, and the ice cubes will raise the

wire shutoff arm to the OFF (arm up) position. Do not force the wire

shutoff arm up or down.

Removing and Replacing Ice Storage Bin:

1. Pull the covering panel up from the bottom and then slide it

back toward the rear.

2. Lift the wire shutoff arm so it clicks into the OFF (up) position.

3. Lift up the front of the storage bin and pull it out.

4. Replace the bin by pushing it in all the way or the dispenser will

not work.

5. To restart ice production, push the wire shutoff arm down to the

ON position. Make sure the door is closed tightly.

REFRIGERATOR FEATURES

Your model may have some or all of these features. Features that

can be purchased separately as product accessories are labeled

with the word “Accessory.” Not all accessories will fit all models. If

you are interested in purchasing one of the accessories, please call

the toll-free number on the back cover or in the “Accessories”

section.

Refrigerator Shelves

(number of shelves varies by model)

Your model may have glass or wire shelves. Store similar foods

together and adjust the shelves to fit different heights. This reduces

the time the refrigerator door is open and saves energy.

Slide-Out Shelves (on some models)

To Remove and Replace a Shelf in a Metal Frame:

1. Pull the shelf forward to the stop. Tilt the front of the shelf up

and lift it slightly as you pull the shelf from the frame.

2. Replace the shelf by guiding it back into the slots on the frame

and pushing the shelf in past the stop.

Shelves and Shelf Frames

To Remove and Replace a Shelf/Frame:

1. Remove the shelf/frame by tilting it up at the front and lifting it

out of the shelf supports.

2. Replace the shelf/frame by guiding the rear shelf hooks into

the shelf supports. Tilt the front of the shelf up until rear shelf

hooks drop into the shelf supports. Check that the shelf is

securely in position.

Deli Drawer

(on some models)

The deli drawer stores raisins, nuts, spreads, and other small items

at normal refrigerator temperatures.

To Remove and Replace the Deli Drawer:

1. Remove the deli drawer by sliding it straight out to the stop. Lift

the front and slide the drawer out the rest of the way.

2. Replace the deli drawer by sliding it back past the stop.

Convertible Vegetable/Meat Drawer,

Crisper and Covers

(on some models)

Crisper and Convertible Vegetable/Meat Drawers

To Remove and Replace Drawers:

1. Slide crisper or meat drawer straight out to the stop. Lift the

front of drawer with one hand while supporting the bottom of

drawer with the other hand and slide the drawer out the rest of

the way.

2. Replace the crisper or meat drawer by sliding it back in fully

past the drawer stop.

Crisper or Vegetable/Meat Drawer Covers

To Remove and Replace Covers:

1. Remove the crisper and meat drawer. Press up in center of

crisper glass insert until it rises above the plastic frame. Holding

the crisper glass firmly, slowly slide the glass insert forward to

remove. Lift crisper cover frame and remove. Repeat steps to

remove the meat drawer cover.

2. Replace back of meat drawer cover frame into supports or

slides on side walls of the refrigerator and lower or slide the

front of the cover frame into place. Slide rear of glass insert

into cover frame and lower front into place. Repeat steps to

replace the crisper cover.

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers

are heavy. Use both hands when removing them to avoid

dropping.

Convertible Vegetable/Meat Drawer

Temperature Control

(on some models)

The convertible vegetable/meat drawer can be adjusted to

properly chill meats or vegetables. The air inside the pan is cooled

to avoid “spot” freezing and can be set to keep meats at the

National Livestock and Meat Board recommended storage

temperatures of 28° to 32°F (!2° to 0°C).

IMPORTANT: To extend freshness, wrap meats in airtight, moisture-

proof materials before storing. Always store meat as

recommended.

Adjusting the Control:

To change a control setting: Move the control to the right (less cold)

or to the left (colder) as desired.

To store vegetables: Set the control to VEG (all the way to the right)

to store vegetables at their optimal storage temperatures (which

need to be warmer than those for meat).

IMPORTANT: If food starts to freeze, move the control to the right

(less cold), toward the VEG setting. Remember to wait 24 hours

between adjustments. Doing so gives the temperature of the food

time to change.

Meat Storage Guide

Store most meat in original wrapping as long as it is airtight and

moisture-proof. Rewrap if necessary. See the following chart for

storage times. When storing meat longer than the times given,

freeze the meat.

Fresh fish or shellfish............................... use same day as purchased

Chicken, ground beef, variety meat (liver, etc.) ....................1-2 days

Cold cuts, steaks/roasts............................................................3-5 days

Cured meats.............................................................................7-10 days

Leftovers - Cover leftovers with plastic wrap, aluminum foil, or

plastic containers with tight lids.

Crisper Humidity Control

(on some models)

You can control the amount of humidity in the moisture!sealed

crisper. Humidity Control is located on the crisper drawer. Adjust

the control to any setting between LOW and HIGH.

LOW (open) lets moist air out of the crisper for best storage of

fruits and vegetables with skins.

■ Fruit: Wash, let dry and store in refrigerator in plastic bag

or crisper. Do not wash or hull berries until they are ready

to use. Sort and keep berries in original container in crisper,

or store in a loosely closed paper bag on a refrigerator

shelf.

■ Vegetables with skins: Place in plastic bag or plastic

container and store in crisper.

HIGH (closed) keeps moist air in the crisper for best storage of

fresh, leafy vegetables.

■ Leafy vegetables: Wash in cold water, drain and trim or

tear off bruised and discolored areas. Place in plastic bag

or plastic container and store in crisper.

Wine or Can/Bottle Rack

(on some models - Accessory)

To Remove and Replace the Wine Rack (left) or Can/Bottle

Rack (right):

1. Remove the rack by pulling it straight out from the shelf.

2. Replace the rack by sliding it in between the shelf and the wall

of the refrigerator.

Utility Bin

(on some models - Accessory)

NOTE: For long-term storage, place eggs in a covered container

or in their original carton on an interior shelf.

FREEZER FEATURES

Your model may have some or all of these features. Features that

can be purchased separately as product accessories are labeled

with the word “Accessory.” Not all accessories will fit all models. If

you are interested in purchasing one of the accessories, please call

the toll-free number on the back cover or in the “Accessories”

section.

Frozen Food Storage Guide

Storage times will vary according to the quality and type of food,

the type of packaging or wrap used (should be airtight and

moisture!proof), and the storage temperature. Ice crystals inside a

sealed package are normal. This simply means that moisture in the

food and air inside the package have condensed, creating ice

crystals.

Put no more unfrozen food into the freezer than will freeze within

24 hours (no more than 2 to 3 lbs of food per cubic foot [907 to

1,350 g per 28 L] of freezer space). Leave enough space in the

freezer for air to circulate around packages. Be certain to leave

enough room for the door to close tightly.

For more information on preparing food for freezing, check a

freezer guide or reliable cookbook.

Freezer Shelf

(number of shelves varies by model)

Style 1

To Remove and Replace the Shelf:

1. Lift the shelf up and off of the supports to remove it.

2. Replace the shelf by placing it in the supports. Check that the

shelf is securely in place.

Style 2

To Remove and Replace the Shelf:

1. Slide the shelf to one side. Tilt the shelf upward to remove the

shelf from the support holes. To remove the left side from the

support holes, pull the shelf up and to the right.

2. Replace the shelf by inserting the left side of the shelf into the

support holes. Lower the right side of the shelf and insert into

support holes.

NOTE: Be sure that both sides of the shelf are positioned evenly

in the shelf support holes and the shelf is secure.

Style 3

To Remove and Replace the Shelf:

1. Lift the shelf up and off the supports.

2. Replace the shelf by lowering it onto the shelf supports. Be sure

that the shelf is securely in place.

Freezer Basket or Bin

(plastic bin on some models)

The freezer basket or bin can be used to store bags of frozen fruits

and vegetables that may slide off freezer shelves.

To Remove and Replace the Freezer Basket or Bin:

1. Remove the basket or bin by sliding it out to the stop. Lift the

front to slide the basket or bin out the rest of the way.

2. Replace the basket or bin by positioning it on the rails. Lift the

basket or bin front slightly while pushing it in fully past the

stops.

DOOR FEATURES

Your model may have some or all of these features. Features that

can be purchased separately as product accessories are labeled

with the word “Accessory.” Not all accessories will fit all models. If

you are interested in purchasing one of the accessories, please call

the toll-free number on the back cover or in the “Accessories”

section.

Door Bins

(on some models)

To Remove and Replace the Bins:

1. Remove the bin by lifting it and pulling it straight out.

2. Replace the bin by sliding it in above the desired supports and

pushing it down until it stops.

Door Rails or Bins

(on some models)

The door rails or bins may be removed for easier cleaning.

Snap-On Door Rails or Bins

To Remove and Replace the Rails or Bins:

1. Remove the rails or bins by pushing in slightly on the front of

the bracket while pulling out on the inside tab. Repeat these

steps for the other end of the rail or bin.

2. Replace the rails or bins by aligning the ends of the brackets

with the buttons on the sides of the door liner. Firmly snap

bracket onto the tabs above the shelf as shown.

Drop-In Door Rails

To Remove and Replace the Rails:

1. Remove the rails by pulling straight up on each end of the rail.

2. Replace the rails by sliding the shelf rail into the slots on the

door and pushing the rail straight down until it stops.

Tilt-out Freezer Door Bin

(on some models)

To Remove and Replace the Bin:

1. Remove the bin by pulling out on the tabs behind the basket to

release it from the door liner.

2. Replace the bin by aligning the tabs with the buttons on the

sides of the door liner. Firmly snap the tabs onto the buttons as

shown.

Chilled Door Bin

(on some models)

Cool air from the freezer is directed to the door bin directly

beneath the vent.

NOTE: The dairy compartment and can rack are not chilled.

Chilled Door Bin Control:

The chilled door bin control is located on the left-hand side of the

refrigerator compartment.

Style 1:

■ Turn the control clockwise (right) to reduce the flow of cold

air to the bin and make it less cold.

■ Turn the control counterclockwise (left) to increase the flow

of cold air to the bin and make it colder.

Style 2:

■ Slide the control to the left to reduce the flow of cold air to

the bin and make it less cold.

■ Slide the control to the right to increase the flow of cold air

to the bin and make it colder.

Tilt-out Fruit Bin

(on some models)

To Remove and Replace the Bin:

1. Remove the bin by lifting it and pulling it straight out.

2. Replace the bin by sliding it in above the desired supports and

pushing it down until it stops.

To Remove and Replace the Bin Parts:

1. Press either release button to open the tilt-out portion of the bin.

2. To remove the tilt-out portion of the bin, press in on the curved

levers on each side of the bin. Pull up and out.

NOTES:

■ The bin cannot be removed if it is tilted out all the way. Tilt

it only part of the way before pressing the curved levers to

remove it.

A. Chilled door bin control

A. Release buttons

La page charge ...

Kenmore 106.5022 Series Manuel utilisateur

Marque: Kenmore

Modèle: 106.5022 Series

Catégorie: Frigos

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Kenmore 106.5022 Series User manual
español: Kenmore 106.5022 Series Manual de usuario

Kenmore 106.5022 Series Manuel utilisateur

Ce manuel convient également à

Kenmore 106.5022 Series Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents