Maytag MHWZ400TB00 Le manuel du propriétaire

Marque: Maytag

Modèle: MHWZ400TB00

Catégorie: Machines à laver

Taper: Le manuel du propriétaire

EPIC

AUTOMATIC WASHER

USE & CARE GUIDE

LAVADORA AUTOMATICA

MANUAL DE USO Y CUIDADO

LAVEUSE AUTOMATIQU E

GUIDE D'UTILISATION ET D'ENTRETIEN

FOR QUESTIONS ABOUT FEAfURES, OPERATION/PERFORMANCE,

PARIS, ACCESSORIES OR SERVICE CALL: 1.800.688.9900

IN CANADA, CALl: 1.800.807.6777

VISIT OUR WEBSI[ E AT WWW.MAYTAG.COM

IN CANADA, WWW.MAY fAG.CA

SI fIENE PREGUNfAS RESPECTO A LAS CARACTERiSTICAS,

FUNCIONAMIENTO, RENDIMIENTO, PARTES, ACCESORIOS O

SERVIC[O TECNICO, LIAME AL; 1.800.688.9900

EN CANAD,g,, LI AME At.: 1.800.807.6777

VISfEE NUESTRO SITIO WEB EN

_/WW.MAYTAG .COM

EN CANADA WWW.MAYEAG.CA

AU CANADA, POUR DES QUESTIONS ,_ PROPOS DES

CARACI ERISTIQUES, DU FONCTIONNEMENT/RENDEMEN[] DES

PIECES, DES ACCESSOIRES OU DU SERVICE, COMPOSEZ I E :

1.800.807.6777

OU VISEfEZ NOfRE SEFE INTERNET ,_

WWW.MAYTAG .CA

W10117443A

_i_:_i_!i!!!i!!_!!!i!!i!!i!!!iiiiiii_ii_!!iiiil!_!!!_!__i_ _i:i!:_:_i!!iii!{i_ii_i!!_{_:!ii!!_!_!_!_!!_iiiiiiiiiiiiiiiiiiiiiiiiiiii_i_i/¸¸

TABLE OF CONTENTS

WASHER SAFETY .................................................................. 3

INSTALLATION REQUIREMENTS ......................................... 5

Tools and Parts ................................................................... 5

Options .............................................................................. 5

kocation Requirements ....................................................... 6

Drain System ...................................................................... 8

Electrical Requirements ...................................................... 9

INSTALLATION INSTRUCTIONS ....................................... 10

Remove Transport System ................................................ 10

Connect the Inlet Hoses ................................................... 10

Route the [)rain Hose ....................................................... 11

Secure the Drain Hose ..................................................... 12

level the Washer .............................................................. 12

Complete Installation ....................................................... 12

FEATURES AND BENEFITS .................................................. 13

WASHER USE ...................................................................... 14

Starting Your Washer ....................................................... 14

Using the Proper Detergent .............................................. 14

Using the Dispenser ......................................................... 15

Pausing or Restarting ........................................................ 16

Changing Cycles, Options and Modifiers ......................... 16

Status I.ights ...................................................................... 17

Cycles .............................................................................. 17

Normal Sounds ................................................................ 19

Options ............................................................................ 19

Modifiers .......................................................................... 19

kaundry Guide ................................................................. 20

LAUNDRY TIPS ................................................................... 21

loading ........................................................................... 21

Stain Removal Guide ....................................................... 22

WASHER CARE .................................................................... 23

Cleaning Your Washer ..................................................... 23

Water Inlet Hoses ............................................................. 24

Vacation, Storage, and Moving Care ................................ 24

TROUBLESHOOTING ......................................................... 25

Washer and Components ................................................. 25

Washer Operation ............................................................ 26

Clothes Care ..................................................................... 28

ASSISTANCE OR SERVICE ................................................... 29

In the U.S.A ...................................................................... 29

]n Canada ......................................................................... 29

WARRANTY ........................................................................ 30

:_!_!_ii_!iii!_i{i!!!iiii!!_iiii!i_!i::i_iiiiii!i!ii!{_::_ji[i_,¸ _!iii!i_:!!!!!i_i_i!!:_:!_:_i_:_;i_iiiiiiiiiiiX:!!!!!!!!!!!!!!!!!!!!!!!!!!!_Z¢

INDICE

SEGURIDAD DE LA LAVADORA ....................................... 31

REQUISITOS DE INSTALACION ........................................ 33

Piezas y herramientas ...................................................... 33

Opciones ......................................................................... 33

Requisitos de ubicaci6n ................................................... 34

Sistema de desag0e ......................................................... 36

Requisitos el6ctricos ........................................................ 36

INSTRUCCIONES DE INSTALACION ................................ 37

Eliminaci6n del sistema de transporte .............................. 37

Conexi6n de las mangueras de entrada ........................... 38

Tendido de la manguera de desag0e ............................... 39

Fijaci6n de la manguera de desagi_e ................................ 39

Nivelaci6n de la lavadora ................................................ 40

Complete la instalaci6n ................................................... 40

CARACTERiSTICAS Y BENEFICIOS .................................... 41

USO DE LA LAVADORA .................................................... 42

Puesta en marcha de la law, dora ..................................... 42

Uso del detergente adecuado .......................................... 42

Uso del dep6sito .............................................................. 43

Pausa o reanudaci6n de la marcha .................................. 44

Cambio de ciclos, opciones y modificadores .................. 44

kuces de estado ............................................................... 45

Ciclos .............................................................................. 46

Sonidos normales ............................................................ 47

Opciones ......................................................................... 47

Modificadores .................................................................. 48

Gu_a para el lavado ......................................................... 49

CONSEJOS DE LAVANDERiA ............................................ 50

C6mo cargar .................................................................... 50

Gu[a para laeliminaci6n de manchas ............................. 5I

CUIDADO DE LA LAVADORA .......................................... 52

C6mo limpiar su lavadora ............................................... 52

Mangueras de entrada de agua ........................................ 53

Cuidado/)ara las vacaciones, el almacenaje o

en caso ae mudanza ........................................................ 53

SOLUClON DE PROBLEMAS ............................................. 54-

kavadora y componentes ................................................. 54

Funcionamiento de la lavadora ....................................... 56

Cuidado de las prendas ................................................... 58

AYUDA O SERVICIO TI_CNICO ......................................... 59

En los EE.UU ................................................................... 59

En Canada1 ....................................................................... 59

GARANTiA ......................................................................... 60

__!_i!!iiiiiiiiiiiiiiiiiiiiiiii::!i!!i_ii!iii!!!!!!!!!!!!!!!!!ili!i!i!!ii!i!!:_ji}> bi_iiiii_'ii_i!!!!!iii_ii:iiii!_!_!i!ii{iiiiiiiiiiiiiiii:i_'!ii!!iiiiiiiill¸i_

TABLE DES MATIERES

S[_CURITI_ DE LA LAVEUSE ................................................. 61

EXIGENCES D'INSTALLATION ........................................... 63

Outillage et pi_ces ........................................................... 6_

Options ............................................................................ 6"¢

Exigences d'emplacement ................................................ 64

Syst&me de vidange ......................................................... 66

Specifications (_lectriques ................................................. 67

INSTRUCTIONS D'INSTALLATION ................................... 68

Elimination des accessoires de transport .......................... 68

Raccordement des tuyaux d'alimentation ........................ 68

Acheminement du tuyau de vidange ............................... 69

Immobilisation du tuyau de vidange ................................ 70

R_glage de I'aplomb de la laveuse ................................... 71

Achever I'installation ....................................................... 71

CARACTI_RISTIQUES ET AVANTAGES ............................... 72

UTILISATION DE LA LAVEUSE ........................................... 73

Mise en marche de la laveuse .......................................... 73

Utilisation du d_tergent appropri_ ................................... 73

Utilisation du distributeur ................................................ 74

Pause et remise en marche .............................................. 75

Changement des programmes, options et modificateurs.. 75

T(!moins lumineux ........................................................... 76

Programmes ..................................................................... 77

Sons normaux .................................................................. 78

Options ............................................................................ 78

Modificateurs ................................................................... 79

Guide de lessivage ........................................................... 80

CONSEILS DE LESSIVAGE ................................................... 81

Chargement ..................................................................... 81

Guide pour I'(!limination des taches ................................ 82

ENTRETIEN DE LA LAVEUSE .............................................. 8:1

Nettoyage de la laveuse ................................................... 83

Robinets d'arriv_e d'eau .................................................. 84

Pr(!cautions _ prendre avant les vacances, un

entreposage ou un d(!m_nagement .................................. 84

DI_PANNAGE ...................................................................... 85

ka laveuse et ses composants ........................................... 85

Fonctionnement de la laveuse ......................................... 87

Entretien des v6tements .................................................... 89

ASSISTANCE OU SERVICE .................................................. 90

Aux Etats-Unis .................................................................. 90

Au Canada ....................................................................... 90

GARANTIE .......................................................................... 91

ili;il¸17171¸¸III¸17171¸¸III¸17171¸¸III¸I¸,!i{{7_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!i_!!ii_ii_!_!_!_!_!_!_!_!_!_!_!_!_!_!7!i!ii!7_!_]i!!_7_!_);_!__i_ bi_i7_7;7ii7______!t7t7ttt7t7ttt7t7ttt!_!_!::!; 7

WASHER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer follow basic precautions,

including the following:

[] Read all instructions before using the washer.

[] Do not wash articles that have been previously cleaned

in, washed in, soaked in, or spotted with gasoline,

dry-cleaning solvents, other flammable, or explosive

substances as they give off vapors that could ignite or

explode.

[] Do not add gasoline, dry-cleaning solvents, or other

flammable, or explosive substances to the wash water.

These substances give off vapors that could ignite or

explode.

[] Under certain conditions, hydrogen gas may be

produced in a hot water system that has not been used

for 2 weeks or more. HYDROGEN GAS IS

EXPLOSIVE. If the hot water system has not been

used for such a period, before using the washing

machine, turn on all hot water faucets and let the water

flow from each for several minutes. This will release

any accumulated hydrogen gas. As the gas is

flammable, do not smoke or use an open flame during

[] Do not allow children to play on or in the washer. Close

supervision of children is necessary when the washer is used

near children.

[] Before the washer is removed from service or discarded,

remove the door or lid.

[] Do not reach into the washer if the drum, tub or agitator is

moving.

[] Do not install or store the washer where it will be exposed to

the weather.

[] Do not tamper with controls.

[] Do not repair or replace any part of the washer or attempt any

servicing unless specifically recommended in this manual or in

published user-repair instructions that you understand and

have the skills to carry out.

[] See "Electrical Requirements" for grounding instructions.

this time.

SAVE THESE INSTRUCTIONS

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiii,![iiiii___!iiii__!iiii__!iiii__!iiii__!iiii__!iiii__!iiii__!iiii__!iiii__!iiii__!iiii__!iiii__!iiii__!iiii__!iiii__!iiii__!iiii__!iiii__!iiii__!iiii__!iiii__!iiii__!iiii__!iiii__!iiii__!iiii__!iiii__!iiii__!iiii__!iiii__!iiii__!iiii__!iiii__!iiii__!iiii__!i!g_iii,i______!i!,ii__i_____!i!g_i,,i____!i!_!i!!ii!!!!:,:!i!i!_!!!!!!:,:,ii!i_:i!l,_iii_!_ii_ii_l,!!!!:!ii_i!il_}iii![Wii!!i_i!,_:,_i[ii_¸ :ili!,!!!!!i:!iiiiiii_l,!!_i_i!ii_li!!i_i!!i!!!iii'!!i!!_i_i_}ii!i!:!:iii'_i¸i______________!_!_'_______________________________________________________________________________________!_!iiiiiiiiiiiiiiiiiiiiiiii[[iii!ii:i ¸

INSTALLATION REQUIREMENTS

bo/s

Gather the required tools and parts before starting installation. The parts supplied are in the

washer drum.

Tools needed for connecting the water inlet hoses

• Pliers (that open to I_A_" 139.5 mm]) • Flashlight (optional)

Tools needed for installation

If You Have You Will Need to Buy

[)rain hose too short 4 ft (1.2 m) drain hose extension kit, Part Number 285863

Water faucets beyond reach 2 longer water fill hoses:

of fill hoses 6 ft (1.8 m) Part Number 76314

10 ft 13.0 m) Part Number 350008

• Open end wrenches I4 mm • Wood block

and 13 mm

• Ruler or measuring tape

• [.evel

Parts supplied

A. U-shaped hose form

B. Water inlet hoses (2)

C. Inlet hose washers (4)

D. lransit bolt hol_" plug (4)

E. Beaded ti_" strap

Pedestal

You have the option of purchasing pedestals of different heights separately for this washer. You

may select a 10" (25.4 cm) or a 15.5" G9A cm) pedestah The pedestal will add to tlne total ......

height of the washer.

CZ>

Alternate Parts

Your installation may require additional parts. [f you are interested in purchasing one of the

items listed here, call the toll-free number on the cover or in the "Assistance or Service"

section.

If You Have You Will Need to Buy

kaundry tub or standpipe Sur'np pump system (if not already available)

taller than 96" (2.4 m)

Overhead sewer Standard 20 gal. (76 1.),30" (76.2 cm) tall drain tub or

utility sink and sump pump (available from local plumbing

suppliers)

Floor drain Siphon break, Part Number 285834; additional drain hose,

Part Number 8318155; and connector kit, Part

Number 285835

Optional pedestal

Pedestal Height Approximate height Color Model Number

with washer

I 0" 125.4 cm/ 46" (116.8 cm/ White MHP1000SQ0

I 0" (25.4 cm) 46" (116.8 cm) Black MHP1000SB0

15.5" (39.4 cm) 51.5" (130.8 cm/ White MHP1500SQ0

15.5" (39.4 cm) 51.5" (130.8 cm) Black MHP1500SB0

15.5" (39.4 cm) 51.5" (130.8 cm/ Blue MHP1500SK0

Stack Kit

Are you planning to stack your washer and dryer? |b do so, you will need to purchase a Stack

Kit.

[b order, call the dealer from whom you purchased your washer or refer to the "Assistance or

Service" section of this manual. Ask for Part Number 8572546.

.... 5

Selecting the proper location for your washer improves performance and minimizes noise and Washer Dimensions

possible washer "walk."

Your washer can be installed under a custom counter, or in a basement, laundry room, closet,

or recessed area. See "Drain System."

Companion appliance location requirements should also be considered. Proper installation is

your responsibility.

You will need

50V£

(127.6crn)

27"

(68.6cm)

A water heater set to deliver 120°F (49°C) water to the washer.

• A grounded electrical outlet located within 6 ft (1.8 m) of where the power cord is

attached to the back of the washer. See "Electrical Requirements."

• Hot and cold water faucets located within 4 ft (1.2 m) of the hot and cold water fill valves,

and water pressure of 20-100 psi (137.9-689.6 kPa/.

• A level floor with a maximum slope of 1" (2.5 cm) under entire washer. Installing the

washer on soft floor surfaces, such as carpets or surfaces with foam backing, is not

recommended.

• A sturdy and solid floor to support the washer with a total weight (water and load) of

400 Ibs (180 kg).

Do not operate your washer in temperatures below ¢2°F (0°C). Some water can remain in the

washer and can cause damage in low temperatures. See "Washer Care" for information on

winterizing.

Installation clearances

• The location must be large enough to allow the washer door to be fully opened.

• Additional spacing should be considered for ease of installation and servicing. The door

opens more than 90 °, and it is not reversible.

• Additional clearances might be required for wall, door, and floor moldings.

• Additional spacing of 1" (2.5 cm) on all sides of the washer is recommended to reduce

noise transfer.

Door is not reversible.

Recommended installation spacing for custom undercounter installation

The dimensions shown are for the recommended spacing.

Custom undercounter installation - Washer only

37"rain.

(93.9 cm)

• Companion appliance spacing should also be considered.

1" --_1_--27"---_i_- 1"

(2.6 cm) ' (68.6 cm) (2.6 crn}

Recommended installation spacing for recessed or closet installation, with or

without a pedestal

The dimensions shown are for tile recommended spacing.

Recessedarea or closet installation

H 1,..,m0x.

--_ 1"_ 36v2"_1 4"

(2.5cm) (77.5crn) (10.2cm)

_-_

46 in.2*_

(310cm2)'

24 in,2*..-:

(165cm2)'

A. Side view - closet or confined area

B. Closet door with vents

*Min. top and bottom air openings for closet door.

Recessed or closet installation - Washer on pedestal

(7.6 crn)

J_- 3"

(7.6crn)

Recommended installation spacing for recessed or closet installation, with

stacked washer and dryer

The dimensions shown are for the recommended spacing.

48in.2*

(310cmz)

24 in.2*

(155cm2)

3" (7.6cm)

5W'** --_,,.

(13.3cm)

12"(_0.5cm}

l ! o i

72"

(182.9cm)

(2.5cm)

1" (2.5cm)

_-27"-_,..- _ 1"t

68.6 cm 2.6 crn

*Min. top and bottom air openings for closet door.

** External exhaust elbow requires additional space.

*Wall, door and floor molding may require additional spacing.

1"_ t<i 27"_1 _ 1" --_11" _ 30v2"_ 4" I._-

(2.5crn} (58.6cm) (2.5crn} (2.5cm) (77.5crn} (10.2cm)

A B

A. R(!ce88(!d ar(!a

B. Side view - closet ot confined area

Recommended installation spacing for cabinet installation

The dimensions shown are for the recommended spacing.

For cabinet installation, with a door, the minimum ventilation openings in the top are

required.

" , )

7"(17.8ore)

(22,9crn)

4 31Y2 1

(10,2cm) (80cm) (2,5cm) (2,5cm) (68,6cm) (2,5cm)

'"7 ...........

The washer can be installed using the standpipe drain system (floor or wall), the laundry tub

drain system, or the floor drain system. Select the drain hose installation method you need.

See "Fools and Parts."

Standpipe drain system - wall or floor (views A & B)

The standpipe drain requires a minimum diameter standpipe of 2" (5 cm). The mmirnunl

carry-away capacity can be no less than 17 gal. (64 l) per minute.

The top of the standpipe must be at least 30" (76.2 cm) high and no higher than 96" (2.4 m)

from the bottom of the washer.

30" rain.

(76,2 cm)

Laundry tub drain system (view C)

The laundry tub needs a minimum 20 gal. (76 I) capacity. The top of the laundry tub must be

at least _¢0" (76.2 cm) above the floor.

Floor drain system (view D)

The floor drain system requires a siphon break that may be purchased separately. See "Fools

and Parts."

The siphon break must be a minimum of 28" (71 cm) from the bottom of the washer.

Additional hoses might be needed.

26"_mi_'n_,

Electrical Shock Hazard

Pluginto a grounded3 prongoutleL

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failureto follow these instructions can result in death,

fire, or electrical shock=

• A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical supply is required. A time-

delay fuse or circuit breaker is recommended. It is recommended that a separate circuit

serving only this appliance be provided.

• This washer is equipped with a power supply cord having a 3 prong grounding plug.

• ]b minimize possible shock hazard, the cord must be plugged into a mating, 3 prong,

grounding-type outlet, grounded in accordance with local codes and ordinances. If a

mating outlet is not available, it is the personal responsibility and obligation of the

customer to have the properly grounded outlet installed by a qualified electrician.

• If codes permit and a separate ground wire is used, it is recommended that a qualified

electrician determine that the ground path is adequate.

.... _ _. _ 5¸ _ _

[!£elr<a

• Do not ground to a gas pipe.

• Check with a qualified electrician if you are not sure the washer is properly grounded.

• Do not have afuse in the neutral or ground circuit.

GROUNDING iNSTRUCTiONS

For a grounded, cord-connected washer:

This washer must be grounded. In the event of a malfunction

or breakdown, grounding will reduce the risk of electrical

shock by providing a path of least resistance for electric

current. This washer is equipped with a cord having an

equipment-grounding conductor and a grounding plug. The

plug must be plugged into an appropriate outlet that is

properly installed and grounded in accordance with all local

codes and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or serviceman if you are in

doubt as to whether the appliance is properly grounded.

Do not modify the plug provided with the appliance - if it will

not fit the outlet, have a proper outlet installed by a qualified

electrician.

For a permanently connected washer:

This washer must be connected to a grounded metal,

permanent wiring system, or an equipment grounding

conductor must be run with the circuit conductors and

connected to the equipment-grounding terminal or lead on

the appliance.

_!!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_![[i_i_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_i_!iii!!_!_!_!_!_i!i!{i!_i!_!ji!!_!_!_!_!!i!i!_i_jii!_!_!_!_!_!!!!i[ii_._!ii!ii!!_jjii!_!iiiiji!!_!_!_!_!_!!i!i_}_!_!_!_!_l!l!!!i!!!_4_, i!i[ii_!!!!_iiiiii}ii}_!!i_i_}_i_iii_!ii_!!!_iiiiii}_!iji_!_!i_ii!ii!_!_!_!_i!_ii_1!_!_!_i!i!ii!!_iii!i)ii_:i_!_i[ii_i_!!__!_i!_!_!_!!i!i!ii!!_ii!!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!!iiiiiiiiiiiiiiiiiiiiiiiiii[[ii;!i_i¸

INSTALLATION INSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install washer.

Failure to do so can result in back or other injury.

IMPORTANT: Position the washer so that the rear of the washer is within approximately 3 ft

(90 cm) of its final location.

There are 4 blue bolts in the rear panel of the washer that support the suspension system

during transportation. These bolts also retain the power cord inside the washer until the bolts

are removed.

1. Using a 13 mm wrench, loosen each of the bolts.

2. Once the bolt is loose, move it to the center of the hole and completely pull out the bolt,

including the plastic spacer covering the bolt.

Insert new flat washers (supplied) into each end of the inlet hoses. Firmly seat the washers in

the couplings.

A B

A. C_;upling

B.Washer

Connect the inlet hosesto the water faucets

Make sure the washer drum is empty.

1. Attach a hose to the hot water faucet. Screw on coupling by hand until it is seated on the

washen

2. Attach a hose to the cold water faucet. Screw on coupling by hand until it is seated on the

washen

3. Using pliers, tighten the couplings with an additional two-thirds turn.

NOTE: Do not overtighten or use tape or sealants on the valve. [Damage to the valves can

result.

3. Once all 4 bolts are removed, discard the bolts and spacers. Then pull the power cord

through the opening of the rear panel and close the hole with the attached cap.

4. Close the bolt holes with the 4 transport bolt hole plugs.

NOTE: If the washer is to be transported at a later date, call your local service center. [b avoid

suspension and structural damage, your machine must be properly set up for relocation by a

certified technician.

Clear water lines

• Run water through both faucets and inlet hoses, into a laundry tub, drainpipe or bucket,

to get rid of particles in the water lines that might clog the inlet valve screens.

• Check the temperature of the water to make sure that the hot water hose is connected to

the hot water faucet and that the cold water hose is connected to the cold water faucet.

Connect the inlet hoses to the washer

Ro ,, e @e Hose

Proper routing of the drain hose protects your floor from damage due to water leakage. Read

and follow these instructions.

Remove drain hose from the washer

Gently pull the corrugated drain hose from the shipping clips.

Laundry tub drain or standpipe drain

Connect the drain hose form to the corrugated drain hose.

H. Hot water inlet

C. Cold water inlet

1. Attach the hot water hose to the washer's hot (H) water inlet valve. Screw on coupling by

hand until it is seated on the washer.

2. Attach the cold water hose to the washer's cold (C) water faucet. Screw on coupling by

hand until it is seated on the washer.

3. Using pliers, tighten the couplings with an additional two-thirds turn.

NOTE: Do not overtighten. Damage to the coupling can result.

4. [urn on the water faucets completely and check for leaks.

NOTE: Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Record

hose installation or replacement dates on the hoses for future reference.

Periodically inspect and replace hoses if bulges, kinks, cuts, wear, or leaks are found.

A B

A. Snap either end of the drain hose form to the drain hose at

the point where the corrugation begins.

B. Bend drain hose over drain hose form and snap h_to place.

To keep drain water from going hack into the washer:

• Do not straighten the drain hose, and do not force excess drain hose into standpipe. Hose

should be secure, but loose enough to provide a gap for air.

• Do not lay excess hose on the bottom of the laundry tub.

Floor drain

You may need additional parts. See Floor drain under "lools and Parts."

!_!!!_i_!_!!iii!iiii_ii!!iiiiiiiiiiiiiiiiiiii_!!_!_i_!_!_!_!iiii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_iiI ii!!S!_!i!ii;_i!!iSi! 11

_J_c¸'_ _IS(_¸I9_8I__°_¸¸¸/_' _"_

1. Drape the power cord over the washer top.

2. Move the washer to its final location.

3. Place the drain hose in the laundry tub or standpipe as shown. See illustrations A and B.

1. Check the electrical requirements, Be sure that you have the correct electrical supply and

the recommended grounding method. See "Electrical Requirements."

2. Check that all parts are now installed. [f there is an extra part, go back through the steps to

see which step was skipped.

3. Check that you have all of your tools.

4. Dispose of/recycle all packaging materials.

5. Check that the water faucets are on.

6. Check for leaks around faucets and inlet hoses.

4. If the washer faucets and the drain standpipe are recessed, put the hooked end of the

drain hose in the standpipe as shown. See illustration C.

NOTES:

• Do not force excess drain hose back into the rear of the washer.

• [b avoid siphoning, do not seal the drain hose into the standpipe.

I _=I =i iI r/ I +_, I 1,1++,I= I _>,=

Properly leveling your washer avoids excessive noise and vibration.

1. Check the levelness of the washer by placing a level on the top edge of the washer, first

side to side, then front to back.

If the washer is against a wail, move the washer out slightly before tipping back. [f the

washer is not level, first prop the front with a wood block and adjust the feet as necessary;

then prop the back and adjust feet as necessary. Repeat this step until washer is level.

2. Make sure all four feet are stable and resting on the floor. Then check that the appliance is

perfectly level (use a level).

3. After the washer is level, use a 14 mm open-end wrench to turn the nuts on the feet tightly

against the washer cabinet.

IMPORIANT: All four feet must be tightened. If the nuts are not tight against the washer

cabinet, the washer may vibrate,

4. The washer should not move front to back, side to side, or diagonally when pushed on its

top edges.

5. Slide the washer to its final location.

6. Confirm the levelness of the washer.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Plug into a grounded 3 prong outlet.

Read "Washer Use."

[b test and to clean your washer, measure V2the detergent manufacturer's recommended

amount of HE High Efficiency detergent for a medium-size load. Pour the detergent into

the detergent dispenser. Select NORMAl, and then select START. Allow the washer to

complete one whole cycle.

Use only HE High Efficiency detergm_t.

Your new front-loading high efficiency washer, was designed to help conserve resources and

lower your water and energy bills. The washer is designed to determine and then provide the

amount of water needed for the best performance. The time of operation may be greater for

this new system than for a conventional washer.

Electronic Controls

Flexible electronic controls are easy to use whether you are a beginner or an expert.

Auto Water Level

Adjusting to the size of the load, this feature allows the washer to use the minimal amount of

water needed to clean and rinse the clothes. With a low water level, you can obtain the same

results with smaller amounts of laundry products. Because only the required amount of water

is used, the washer saves energy, too. You can obtain the same washing results for small and

large loads size.

Larger Load Size

Since there is no agitator, you can wash larger, bulkier items such as an average size sleeping

bag. You are also able to wash more clothes at one time, which means fewer loads. You can

wash a pillow or a large stuffed teddy bear.

Suspension System

lb reduce washer "walk" and "off-balance" conditions, your new washer combines:

• 2 Springs to isolate vibration

• 4 Shock absorbers at the washer base to minimize movement

Stainless Steel Drum

The stainless steel drum eliminates corrosion and enables higher spin speeds for more water

extraction, helping to reduce drying time.

Adaptive Variable Speed Motor

The motor adapts to the load size and to the cycle selected to give the optimum cleaning,

rinsing, and spinning conditions. The motor can handle slow speeds needed for delicate items

and is powerful enough to drive an average clothes load up to high-speed spin.

Spin Speeds

This washer automatically selects the spin speed based oil the cycle selected. [his factory

setting can be changed, however. This washer offers up to three different spin speed choices.

Thermal Optimizer

The heating system ensures that the wash water is heated to the preset temperature for Super

Wash, Whites, and Sanitary cycles. It also provides "Stepped Cleaning" when using the

Sanitary cycle. "Stepped Cleaning" starts the wash cycle with warm water to remove stains

/such as blood or grass). The Sanitary cycle also helps eliminate 99.9% of K. pneumonia, R

aureginosa and S. aureus, which are three common infectious bacteria.

Add A Garment

This option is available in all wash cycles except Rinse & Spin, Spin Only and Clean Washer.

When this option is available at the beginning of the cycle, the Add A Garment status light

will illuminate for the first 7 minutes. [-his washer allows a 7-minute period in which other ,1

garments may be added to a load.

Dynamic Balance

A precision balancing system that allows the washer to reach high-speed spins. [-he washer

spins faster so that clothes coming out of the washer will have less moisture than with

traditional top load machines. [n addition, if the Dynamic Balance system detects off-balance

loads during spinning, it redistributes the clothes so that they are evenly balanced.

Detergent Advantage System Dispenser

The three compartments in the dispenser allow loading of all laundry products before the

washer is started. [-he products will be dispensed into the wash at the optimal time for high-

performance cleaning. The bleach release system is included in the detergent advantage

system. [-he detergent is added at the beginning of the cycle, and the bleach is added after the

enzymes have had a chance to do their cleaning. The fabric softener is dispensed in the rinse

cycle or in the EXTRA RINSE, if selected. The Detergent Advantage System Dispenser tray can

be easily removed for cleaning.

Use only HE High Efficiency detergent.

ADD A GARMENT

aREWASH

WASH

RINSE

SPIN

CLEAN

CONTROLS LOCKED ;_j

DOOR LOCKED

POWER

RAPID

EX HOT/COLD

START i/iMEDIUM i/i WARM/WARM

PAUSE/

CANCEL LOW WAtM/COLD

Q NO SPIN COLD/COLD

SPIN WASH/RINSE

SPEED TEMP

CO_OL

NOTE: [he panel shown above may be different from that of your model.

Fire Hazard

Never place items in the washer that are dampened

with gasoline or other flammable fluids.

No washer can completely remove oil.

Do not dry anything that has ever had any type of oil on

it (including cooking oils).

Doing so can result in death, explosion, or fire.

WARNING: ]b reduce the risk of fire, electric shock, or injury to persons, read the

IMPORTANT SAFETY INSTRUCTIONS before operating this appliance.

]he following is a guide to using your washer. Please refer to specific sections of this manual

for more detailed information.

Do not store laundry products on the top surface of this washer. Vibration is normal during

operation.

O PREWASH

O MAX EXTRACT

O STAIN CYCLE

i EXTRA RINSE

Use only High Efficiency detergents. The package for this type of detergent will be marked

"HE" or "High Efficiency." This wash system, along with less water, will create too much

sudsing with a legulal non-HE detelgenL Using legulal detelgen[ will likely result in washel

errors, longer cycle times, and reduced rinsing performance. It may also result in component

failures and noticeable mold or mildew. HE detergents are made to produce the right amount

of suds for the best performance. Follow the manufacturer's instructions to determine the

amount of detergent to use.

Use only HE High Efficiency detergent.

First Wash Cycle Without Laundry

Before washing clothes for the first time, if not completed during the final installation step,

choose the Normal cycle and run it without clothes. Use only HE High Efficiency detergent.

Use _/_the manufacturer's recommended amount for a medium-size load. This initial cycle

serves to ensure the interior is clean before washing clothes.

14.

For All Wash Cycles

To load washer

Open the washer door by pulling on the handle. Sort laundry according to color and type

of fabric. Place a load of sorted clothes in the washer. Do not overload washer.

Overloading can cause poor cleaning.

• The washer can be fully loaded, but not tightly packed. Washer door should close

easily.

• Mix large and small items. Avoid washing a single item. [.oad evenly.

• Wash small items such as infant socks in mesh garment bags. [t is recommended that

more than one garment bag be used and that each garment bag be filled with equal

amounts of material.

• When unloading garments, occasionally check under the gray colored seal/bellow

rim at the front of the tub for small items.

2. Close the washer door by pushing it firmly until the lock clicks. The washer door will

remain locked during the wash cycle.

NOTE: The door can be opened only if PAUSE/CANCEL is selected while the ADD A

GARMENT light is illuminating or if the cycle has been canceled. See "To cancel a cycle"

in the "Changing Cycles, Options and Modifiers" section.

3. Open the dispenser drawer and add laundry products to the detergent, bleach, or fabric

softener compartments. Close drawer slowly to avoid spills. See "Using the Dispenser."

NOTE: Use only HE High Efficiency detergent.

4. [urn on the washer by selecting POWER. Select one of the cycles by turning the cycle

selector. The indicator light for the selected cycle will illuminate. When selecting a Wash

Cycle, the preset Modifiers and Options, Water [emp, and Spin Speed for the selected

cycle will illuminate. [he preset settings provide the recommended fabric care for the

selected cycle. See "Cycles."

5. Select the desired OPTIONS such as Prewash, MAXEXTRACT _s, Stain Cycle or Extra

Rinse. Not all Options are available with all cycles. See "Options."

6. Select the desired MODIFIERS, such as Spin Speed and Wash/Rinse lemp. Not all

Modifiers are available with all Cycles and Options. See "Modifiers."

7. If desired, select the CYCI.E SIGNAL. The signal is helpful when you are washing items

that should be removed from the washer as soon as it stops. Press CYCI.E SIGNAl once to

turn it on. [-he indicator light will illuminate, Press again to turn it off.

8. To begin the wash cycle immediately

Select and hoM START (for approximately 1 second).

• If you do not select START within 5 minutes of choosing a cycle, the washer

automatically shuts off.

• When the wash cycle is complete, the CLEAN status light illuminates, the door

unlocks, and the wash load can be removed from the washer. The washer powers

down automatically 5 minutes after the cycle is complete and the Clean Eight stays on

until the door is opened or PAUSE/CANCEl is selected. [b power down the washer

manually after the wash cycle is complete, select PAUSE/CANCEL once.

To begin the wash cycle later

Select DEI.AY WASH until the desired delay time (in hours) shows in the Estimated Time

Remaining display. Select SrARE The countdown to the wash cycle will show in the

display window.

IMPORTANT: When delaying a cycle, use only powdered detergents in the main wash

compartment since liquid detergents may seep out of the compartment during Delay,

before the wash cycle begins.

Your new washer has a dispenser drawer with three separate compartments for your laundry

products one is for detergent, one is for liquid chlorine bleach, and one is for liquid fabric

softener, laundry products are diluted and dispensed automatically at the proper time during

the wash cycle, making it unnecessary for you to return to the washer during the cycle to add

them.

it is normal for small amounts of water to remain in the dispensers when the wash cycle is

complete.

Do not put laundry products directly into the wash tub. Always use the proper dispensers

when adding laundry products.

Choosing the Right Detergent

Use only High Efficiency detergents. The package for this type of detergent will be marked

"HE" or "High Efficiency." This wash system, along with less water, will create too much sudsing

with a regular non-HE detergent. Using regular detergent will likely result in washer errors, longer

cycle times, and reduced rinsing performance. It may also result in component failures and

noticeable mold or mildew. HE detergents are made to produce the right amount of suds for the

best pertormance. Follow the manufacturer's instructions to determine the amount of detergent

to use.

Use only HE High Efficiency detergent.

To fill dispenser compartments

1. Pull out the dispenser drawer.

2. Add the desired laundry product to the proper compartment.

3. PushinthedispenserdrawerslowlyandcompletelyItoavoidaspill).

Dispenser

B. Main l/Vash detergent compartment

C. liquid chlorine bleach compartment

D. Fabric softener compartm(!llt

Main Wash detergent compartment

([ c'tter B in Dispenser Illustration)

Add liquid or powdered HE detergent to this compartment for your main wash cycle.

• Powdered color-safe bleach may be added to the Main Wash compartment along with the

powdered detergent.

• Use the measurement device which comes with the detergent. Add no more than the

manufacturer's recommended amount.

NOTE: Overfilling could cause an oversudsing condition.

Chlorine bleach compartment

(Letter C in Dispenser Illustration)

Add NO MORE THAN ¾ cup (160 m[) liquid chlorine bleach to this compartment. The

bleach will be automatically diluted and dispensed at the best time during the first rinse after

the wash cycle. This compartment cannot dilute powdered bleach.

• Use only liquid chlorine bleach in this dispenser. Do not use this dispenser to add

powdered chlorine or any form of color-safe bleach to your load.

• Always measure liquid chlorine bleach. Use a measuring cup with a pour spout; do not

guess. Follow the manufacturer's directions for proper use.

• Do not fill beyond the "MAX" level.

NOTE: Overfilling could cause garment damage.

Fabric softener compartment

(letter D in Dispenser Illustration)

Add V4 cup (60 ml.) liquid fabric softener to this compartment. Fabric softener will be

automatically dispensed in the final rinse or in the EXTRA RINSE, if selected.

• Do not fill beyond the "MAX" level.

1. [b pause the washer at any time, select PAUSE/CANCEl..

2. [b continue the cycle, select and hold START (for approximately 1 second).

Not all Options and Modifiers are available with all Cycles.

Cycles, Options and Modifiers can be changed anytime before START is selected.

To stop a cycle and select a new cycle

1. Select PAUSE/CANCEl twice.

2. Select POWER.

3. Select desired cycle.

4. Select the desired OPTIONS such as Prewash, MAXEXTRACT _, Stain Cycle or Extra

Rinse.

5. Select the desired MODIFIERS such as Spin Speed or Wash/Rinse Temp.

6. Select and hold START (for approximately 1 second) to restart the washer at the beginning

of the new cycle.

To cancel a cycle

1. Select PAUSE/CANCEl. twice.

2. ]he washer powers down, the door unlocks, and clothes can be removed.

NOTE: If the water level or the temperature is too high, the washer will drain automatically

before the door unlocks.

To change Options or Modifiers after the cycle has started

1. Select PAUSE/CANCEl.

2. Select the desired Spin Speed, Wash/Rinse [_mp or OPTION (such as Prewash,

MAXEXTRACT_L Stain Cycle or Extra Rinse). If the modifier or option are not available,

the machine will beep.

3. Select and hold START (for approximately 1 second) to continue the cycle.

To drain the washer manually

1. Select PAUSE/CANCEL.

2. SelectSPIN Only.

3. Select and hold START (for approximately 1 second) to begin the drain.

4. When the spin is complete, the door unlocks. Items can be removed from the washer.

These lights show which portion of the cycle the washer is operating. They also indicate when

you can add all additional item to the wash cycle and when the controls are locked.

ADD A GARMENT

PREWASH

WASH

RINSE

SPIN

CLEAN

CONTROLS LOCKED

DOOR LOCKED _

Adding items

You can add items to the washer after the wash cycle has started, if the ADD A GARMENT

status light is illuminating. All cycles have this feature except Rinse & Spin, Spin Only and

Clean Washer.

To add items

1. Select PAUSE/CANCEl_ The washer door unlocks, and items can be added.

2. lb continue the cycle, close the door and select and hold START (for approximately

1 second).

NOTE: lb add garments after the ADD A GARMENT period is over, the wash cycle needs to

be canceled, the items added, and a new wash cycle started.

Clean

The Clean light comes on when the cycle is complete. The light will stay on until the door is

opened or PAUSE/CANCEl. is selected.

Locking controls

The Control [.ock avoids unintended use of the washer. You can also use the control lock

feature to avoid unintended cycle or option changes during a cycle. When CONTROl S

[ OCKEL3 is lit, all buttons are disabled except for PAUSE/CANCEl and POWER. You can lock

the controls while the washer is operating.

To lock the controls

Select and hold CYCLE SIGNAl for "_seconds.

O _i_ CYCLE SIGNAL

HOLD3SECONDSTO

[LOC_UNIOCKCONTR01$

The CONTROl S [OCKED status light illuminates.

To unlock the controls

Select and hold CYCI.E SICNAI. for 3 seconds until the C()NTROI.S I.OCKED Status light

turns off.

Estimated Time Remaining

The cycle times vary automatically based on your water pressure, water temperature,

detergent, and clothes load. The cycle time will be extended if oversudsing occurs or the load

is unbalanced. The SUDs routine removes extra suds and assures proper rinsing of your

garments. The options you select will also affect the cycle times that are shown in the Preset

Cycle Settings table. The Estimated Time Remaining can change up to 30 minutes under

extreme conditions. During the unbalace routine the time displayed may pause until this

activity is complete, then resume with the remainder of the cycle.

Door Locked

When the status light illuminates, the door is locked.

FF_

Wash Cycles

Choose Wash Cycle by rotating the Cycle selector knob to the desired cycle. The indicator

light for the cycle selected will illuminate. Each cycle is designed for different types of fabric

and soil levels.

NOTE: [he cycle selector shown below may be different from that of your model.

RAPID

WASH

DELICATE

HAND

WASH

SUPER

SPIN

WASH- "ONLY

RINSE

WHITES- - & SPIN

LEAN

WASHER

Each cycle has a preset cycle time, WASH/RINSE TEMP, SPIN SPEED and may have preset

Options. The preset settings provide the recommended fabric care for the selected cycle.

[he preset settings can be changed anytime before START is selected. Not all Options and

Modifiers are available with all Cycles. 1o change settings after the cycle has started,

select PAUSE/CANCEl, then select the desired settings. Select and hold START (for

approximately 1 second) to continue the cycle.

Preset Cycle Settings

Each cycle has a preset Cycle Time, Water Temp, and Spin Speed. ]he preset settings provide

the recommended fabric care for the selected cycle. See chart.

Cycle Estimated Time* Wash/Rinse Temp Spin Speed

(hr:min)

Sanitary 3H Extra Hot High

Whites 90 - 2H Hot High

Super Wash 90 Hot High

Normal :56 Warm High

Rapid Wash :30 Warm High

(2-3 items)

Delicate :34 Cold low

Handwash :37 Cold low

Spin Only :14 N/A High

Rinse & Spin :26 Cold High

Clean Washer :56 N/A High

detergent, and clothes load. The cycle time will be extended if oversudsing occurs or the

load is unbalanced.

Sanitary

Use this cycle to clean heavily soiled, colorfast fabrics. This cycle combines an extra hot

water temperature and fast speed tumbling to help ensure the removal of heavy soils and

stains. [t is recommended that you set your hot water heater to 120°F (49°C) to ensure proper

performance during this cycle.

Whites

This cycle is especially designed for cleaning loads of soiled white fabrics with the addition of

bleach. Hot washing temperatures assure optimal bleach activity. An additional rinse provides

optimal rinse performance to avoid chlorine residue on your laundry. This cycle combines

fast-speed tumbling, longer wash time, and high-speed spin to shorten drying time.

Super Wash

Use this cycle to wash loads of sturdy, colorfast fabrics and Heavy soiled garments. This cycle

combines fast-speed tumbling, longer wash time, and high speed spin to shorten drying times.

Normal

Use this cycle to wash loads of no-iron fabrics such as sport shirts, blouses, casual business

clothes, permanent press blends, coKons and linens, and synthetic fabrics. This cycle combines

medium-speed tumbling, high-speed spin, and a load cooling process to reduce wrinkling.

Rapid Wash

Use this cycle to wash small loads of lightly soiled garments that are needed in a hurry. This

cycle combines fast-speed tumbling, a shortened wash time, and high speed spin to shorten

drying time. I.arge wash loads will result in the machine increasing the wash time.

Delicate

Use this cycle to clean washable silk and ultra delicate garments. (Check label instructions to

make sure that garment is washable.) [his cycle gently tumbles and drains without spinning to

gently clean garments and minimize wrinkling. Garments will contain a higher amount of

water at the end of this cycle, because there is a low spin-speed at the end of the cycle.

• Use mesh garment bags to wash undergarments such as underwire bras, items with

strings, and small items such as socks.

Handwash

Use this cycle to clean washable woolen and special care garments. (Check label instructions

to make sure that the garment is washable.) Similar to the way garments are hand washed in a

sink, the wash action of this cycle combines periods of extra low tumbling speeds and

soaking. Low spin speeds minimize wrinkling.

• Use mesh garment bags as needed.

Spin Only

Use this cycle to drain your washer or to drain and spin your wash load. The spin speed is

preset to high. If desired, you can reduce the spin speed by selecting the speed you want from

the SPIN SPEED modifier.

NOTE: Loads of synthetics, delicate fabrics, handwashables, and woolens should be drained

with no spin or low spin to avoid fabric stress.

To use Spin Only setting

• Select SPIN Only cycle.

• Press STARE

Rinse & Spin

Use this cycle to rinse, drain, and spin your wash load. This cycle combines fast-speed

tumbling and high-speed spin. If desired, you can reduce the spin speed by selecting the

speed you want from the SPIN SPEED modifier.

Rinse & Spin is useful for

• Loads that need rinsing only.

• Adding fabric softener to a load using the fabric softener dispenser.

Clean Washer

Use the Clean Washer cycle once a month to keep the inside of your washer fresh and clean.

This cycle uses a higher water level in combination with liquid chlorine bleach to thoroughly

clean the inside of your washing machine. See "Cleaning Your Washer" in the Washer Care

section.

IMPORTANT: Do not place garments or other items in the washer during the Clean Washer

cycle. Use this cycle with an empty wash drum.

As with any new product, you will hear sounds that you are not accustomed to. You may hear

various sounds when the door is locked or unlocked, and during the washing, rinsing, or

spinning process. Between changes in wash actions, there will be momentary pauses. You

will hear water spraying and splashing during the wash and rinse cycles. These new sounds

and pauses are part of normal washer operation. See "Troubleshooting."

You can customize your wash by adding options to your cycle selections. You can add or

change an option after starting a cycle anytime before the selected option begins. Not all

options are available with all cycles.

O @ PREWASH

O @ MAX EXTRACT

O _ STAIN CYC£E

O EXTRA RINSE

• See the "laundry Guide" section for an overview of possible options for each Wash Cycle

selection.

• If an option is available with a selected cycle, the light for that option will illuminate

when selected.

• If an option is unavailable with a selected cycle, there will be a short tone and the light for

that option will not illuminate when selected.

Prewash

Use this option for loads of heavily soiled items that need pretreatment.

• Add detergent to Main Wash compartment of the dispenser drawer.

]his option adds tumbling time prior to the selected main cycle. The washer continues

automatically from prewash into the main wash cycle.

Stain Cycle

Use this option for heavily soiled loads that need improved stain treatment. When Stain Cycle

is selected, the water temperature of the selected wash cycle is automatically set to warm. The

water will then be heated to a hot water temperature to aid in stain removal. ]his option will

provide optimal removal of organic stains such as blood.

Extra Rinse

An extra rinse can be used to aid in the removal of detergent or bleach residue from garments.

This option provides an additional rinse with the same water temperature as the Normal rinse.

Cycle Signal

This signal is helpful when you are removing items from the washer as soon as it stops, Select

ON or OFF.

Preset cycle settings of Wash/Rinse Temperature and Spin Speed can be changed. You can

change a modifier after starting a cycle anytime before the selected Modifier begins. Not all

modifiers are available with all options and cycles.

iI EX HOT/COLD

HIGH i HOT/COLD

l MEDIUM ii WARM/WARM

_i_LOW _iiiiWARM/COLD

i_NO SPIN ii COLD/COLD

Q 0

SPIN WASH/RINSE

SPEED TEMP

ALLAUTO TEMP

CONTROL

lb change the spin speed, select the SPIN SPEED button until the desired setting

illuminates.

lo change the water temperature, select the WASH/RINSE TEMP button until the desired

setting illuminates.

Wash/Rinse Temp

Select a water temperature based on the type of load you are washing. Use the warmest wash

water safe for fabrics. Follow garment label instructions.

Warm rinses leave the loads dryer than cold rinses. Warm rinses increase wrinkling. In cold

climates, a warm rinse makes the load more comfortable to handle. Cold rinses save energy.

Temperature Guide

Wash Water Temperature Suggested Fabrics

EXTRA HOT Sturdy colorfast fabrics

Heavy soils

HOT Whites and pastels

Heavy soils

WARM Bright colors

Moderate to light soils

COLD Colors that bleed or fade

Light soils

[n wash water temperatures colder than 60°F (15.6°C), detergents do not dissolve welh Soils

may be difficult to remove.

Auto Temp Control

ATC (Auto |emp Control) electronically senses and maintains a uniform water temperature.

ATC regulates incoming hot and cold water. The AlC is automatically turned ON when a

cycle is selected. See Preset Cycle Settings table in "Cycles."

• ATC works for the wash temperature with Extra Hot/Cold, Hot/Cold, Warm/Warm, Warm/

Cold, and Cold/Cold settings.

• ATC works for the rinse temperature with the Warm/Warm setting.

• The Cold rinse temperatures depend on the cold water at your faucet.

Refer to this chart for suggested load types and their corresponding cycles. Listed to the right are the options available to each of these washer cycles.

CYCLE SUGGESTED LOAD TYPE AVAILABLE OPTIONS