Axis 2400/01 Manuel utilisateur

AXIS 2400/01 Video Server

Professional Surveillance and Monitoring over TCP/IP

Administration Manual

Includes support for AXIS 2191 Audio Module

AXIS COMMUNICATIONS

<Product Name> Quick User’s Guide

AXIS 2400/2401 Admin Manual

2

About This Document

This manual is intended for both administrators and users

of the AXIS 2400/2401 Video Server, and is applicable for

software release 2.31. It includes simple step-by-step

instructions for configuring, managing and using the

AXIS 2400/2401 Video Server on your network.

Previous experience of networking will be of use to the

reader when installing and using this product. Some

knowledge of UNIX or Linux-based systems would also be

beneficial, for developing custom PHP-based

programming scripts and applications.

Readers should use this document as a supplement to the

Wizards and other on-line information available via the

Web-based interface. Later versions of this document will

be posted to the Axis Website, as required.

Safety Notices

Please observe all safety markings when using this

product.

Caution! - Potential hazard that can damage the product.

Important! - Potential hazard that can seriously impair

operation.

Do not proceed beyond any of the above notices until you

have fully understood the implications.

Legal Considerations

Camera surveillance can be prohibited by laws that vary

from country to country. Check the laws in your local

region before using the AXIS 2400/2401 for surveillance.

Electromagnetic Compatibility (EMC)

USA - This equipment generates, uses, and can radiate

radio frequency energy and if not installed and used in

accordance with the instruction manual, may cause

interference to radio communications. It has been tested

and found to comply with the limits for a Class A

computing device pursuant to Subpart B of Part 15 of FCC

rules, which are designed to provide reasonable protection

against such interference when operated in a commercial

environment. Operation of this equipment in a residential

area is likely to cause interference, in which case the user

at his/her own expense will be required to take whatever

measures may be required to correct the interference.

Shielded cables should be used with this unit to ensure

compliance with the Class A limits.

Europe - This digital equipment fulfills the

requirements for radiated emission according to limit B of

EN55022/1994, and the requirements for immunity

according to EN50082-1/1992 residential, commercial,

and light industry.

Liability

Every care has been taken in the preparation of this manual;

if you detect any inaccuracies or omissions, please inform

your local Axis office. Axis Communications AB cannot be

held responsible for any technical or typographical errors and

reserves the right to make changes to the product and

manuals without prior notice. Axis Communications AB

makes no warranty of any kind with regard to the material

contained within this document, including, but not limited to,

the implied warranties of merchantability and fitness for a

particular purpose. Axis Communications AB shall not be

liable nor responsible for incidental or consequential damages

in connection with the furnishing, performance or use of this

material.

Trademark Acknowledgments

Acrobat, Adobe, Boa, Ethernet, IBM, Internet Explorer, LAN

Manager, Linux, Macintosh, Microsoft, Netscape Navigator,

OS/2, UNIX, Windows, WWW are registered trademarks of the

respective holders. Java and all Java-based trademarks and

logos are trademarks or registered trademarks of Sun

Microsystems, Inc. in the United States and other countries.

Axis Communications AB is independent of Sun

Microsystems Inc.

Support Services

Should you require any technical assistance, please contact

your Axis reseller. If your questions cannot be answered

immediately, your reseller will forward your queries through

the appropriate channels to ensure a rapid response. If you are

connected to the Internet, you can:

• download user documentation and firmware updates

• find answers to resolved problems in the FAQ database.

Search by product, category, or phrases

• report problems to Axis support staff by logging in to

your private support area

• visit the Axis Support Web at www.axis.com/techsup/

AXIS 2400/2401 Administration Manual

Revision 2.11

Part No: 19097

Dated: April 2002

1996 - 2002

AXIS 2400/2401 Admin Manual 3

Table Of Contents

Product Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

AXIS 2400 Front Panel ..................................................6

AXIS 2401 Front Panel ..................................................7

AXIS 2400/2401 Rear Panel ..............................................8

Hardware Inventory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Installing on a Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Verifying and Completing the Installation From Your Browser ..................10

Installing via the Null Modem Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Step A - Connecting Your Computer Using the Null Modem Cable ...............11

Step B - Creating a Dial-Up Networking Connection ..........................12

Verifying the Modem Connection and Completing the Installation ...............13

Configuring the Video Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

The Administration Tools ...............................................14

Designing your Application .............................................17

General Server Settings ................................................18

Network Settings ....................................................20

Dynamic IP Address Notification Settings ..................................21

Video Settings .......................................................22

Serial Port Settings ...................................................24

Pan Tilt Settings .....................................................26

Modem Settings .....................................................26

Reinstating the Factory Default Settings ...................................27

Using the Video Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Accessing your Surveillance Images .......................................28

Positional Control of the Video Sources ....................................30

The AXIS 2191 Audio Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Installing the Audio Module ............................................33

Configuring the Audio Module ..........................................34

Using the Audio Module with Your Video Server .............................35

Appendix A - Other IP Setup Methods. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Notes for Macintosh Users .............................................38

Using the AXIS IP Installer ..............................................39

Appendix B - Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

AXIS 2400/2401 Admin Manual

4

PINGing Your IP Address ...............................................41

Appendix C - Updating the Firmware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Obtaining Updated firmware ............................................44

Updating the firmware .................................................44

Appendix D - Customizing The Video Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Modifying the File System ..............................................45

Configuring using FTP .................................................45

Custom Web Pages ...................................................46

Appendix E - Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Appendix F - The RS-232 Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Physical Connector ...................................................51

Connecting Pan/Tilt Devices .............................................52

Appendix G - The I/O Terminal Block. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Controlling and Monitoring .............................................55

Produktbeschreibung und Installationsanleitung

Produktbeschreibung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

AXIS 2400 Bedienfeld, Ansicht von vorne ..................................57

AXIS 2401 Bedienfeld, Ansicht von vorne ..................................58

AXIS 2400/2401 Bedienfeld, Ansicht der Rückseite ...........................59

Lieferumfang . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Installation im Netzwerk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Überprüfen und Abschließen der Installation von Ihrem Browser aus .............61

Installation über Modem. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Schritt A - Anschließen Ihres Computers über das Null-Modemkabel .............62

Schritt B - Erstellen einer DFÜ-Netzwerkverbindung ..........................63

Überprüfen der Modemverbindung und Abschliesen der Installation ..............64

Werkseitige Standardeinstellungen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Decsription du Produit et Guide d’Installation

Description du produit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Panneau avant du serveur AXIS 2400 .....................................66

Panneau avant du serveur AXIS 2401 .....................................67

AXIS 2400/2401 Admin Manual 5

Panneau arrière du serveur AXIS 2400/2401 ................................68

Liste du matériel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Installation sur un réseau . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Vérification et fin d’installation à partir de votre navigateur ....................70

Installation à l’aide d’un modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Etape A - Connexion à l’aide du câble "Null Modem" .........................72

Etape B - Création d’une connexion d’accès réseau à distance ..................73

Vérification et fin d’installation de la connexion modem .......................74

Des paramètres d’usine par défaut. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Descripción del producto y Guía de instalación

Descripción del producto . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

AXIS 2400 Panel frontal ...............................................76

AXIS 2401 Panel frontal ...............................................77

AXIS 2400/2401 Panel posterior .........................................78

Inventario de hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Instalar en una red . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Verificando y completando la instalación desde su buscador web ...............80

Instalar a partir de un módem. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Paso A - Conectar su ordenador usando el Cable de módem nulo ................82

Paso B - Crear un acceso telefónico a redes ................................83

Verificar la conexión de módem y completar la instalación .....................84

Incluir los parámetros por defecto . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Product Description AXIS 2400/2401 Admin Manual

6

Product Description

Read the following information to familiarize yourself with the AXIS 2400/2401, making

particular note of where the connectors and indicators are located.

AXIS 2400 Front Panel

DIP Switches

A corresponding line termination

switch for each of the supported

video outputs. All units are

shipped with the line termination

enabled for each supported video

input; that is, with the DIP

switches set in the down-position.

If the AXIS 2400 is to be con-

nected in parallel with other

equipment, disable the input ter-

mination by turning the corre-

sponding DIP switch to the

up-position (OFF). Failure to do

this can cause the picture quality

to be impaired.

Serial Number

Located on the underside label of the AXIS

2400, the serial number is identical to the

Ethernet address of the unit.

Status Indicator

The multi-colored status indicator shows

the operational status of the server, as

described below:

• green - the indicator flashes briefly

and momentarily displays orange

during the start-up and self-test

routines; the indicator then displays

green to indicate a healthy unit sta-

tus.

• red - the indicator will display red

only if a problem with the AXIS

2400 has occurred

• orange - flashes orange when reset-

ting the factory default settings.

Network Indicator

After completion of the startup

and self test routines, the

multi-colored Network Indicator

flashes independently, as fol-

lows:

• yellow - indicating net-

work activity on a 10Mbps

Ethernet network

• green - indicating network

activity on a 100Mbps Fast

Ethernet network

• red - indicating no physical

connection to the network.

Power Indicator

The Power indicator is normally lit while

power is applied. If it is not lit, or it

flashes, there is a problem with the AXIS

2400 external power source.

Control Button

This button is recessed within the product cas-

ing. Using a suitably pointed object, press this

button to restore the factory default settings,

as described in Network Settings, on page 20.

Video Inputs

Accommodates up to 4 separate video sources

(VIDEO 1- VIDEO 4) simultaneously.

Each supported video input is terminated using a

coax/BNC connector. Physical connections made

using RG59, 75 Ohm coax video cable; have a rec-

ommended maximum length of 800 feet (250

meters).

http://www.axis.com

AXIS 2400 Video Server

STATUS

NETWORK

POWER

VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4

75 ON

1 2 3 4

AXIS 2400/2401 Admin Manual Product Description 7

AXIS 2401 Front Panel

DIP Switch

A single line termination for the

supported video output. Units are

shipped with the line termination

enabled; that is, with the DIP

switch set in the down-position.

If the AXIS 2401 is to be con-

nected in parallel with other

equipment, disable the input ter-

mination by turning the corre-

sponding DIP switch to the

up-position (OFF). Failure to do so

can cause the picture quality to

be impaired.

Serial Number

Located on the underside label of the AXIS

2401, the serial number is identical to the

Ethernet address of the unit.

Status Indicator

The multi-colored status indicator

defines the operational status of the

server, as described below:

• green - the indicator flashes briefly

and momentarily displays orange

during the start-up and self-test

routines; the indicator then displays

green to indicate a healthy unit sta-

tus.

• red - the indicator will display red

only if a problem with the AXIS

2401 has occurred

• orange - flashes orange when reset-

ting the factory default settings.

Network Indicator

After completion of the startup

and self test routines, the

multi-colored Network Indica-

tor flashes independently, as

follows:

• yellow - indicating network

activity on a 10Mbps

Ethernet network

• green - indicating network

activity on a 100Mbps Fast

Ethernet network

• red - indicating no physical

connection to the network.

Power Indicator

The Power indicator is normally lit while

power is applied. If it is not lit, or it

flashes, there is a problem with the AXIS

2401 external power source.

Control Button

This button is recessed

within the product casing.

Using a suitably pointed

object, press this button to

restore the factory default

settings. For further infor-

mation, refer to Network

Settings, on page 20.

Video Input

Coaxial BNC connector support-

ing a single video source. The

physical connection is made using

RG59, 75 Ohm coax video cable;

with a recommended maximum

length of 800 feet (250 meters).

Video Output

A single video

loopthrough (VIDEO

OUT) connected in

parallel with VIDEO IN

and terminated with a

coax/BNC connector.

Allows direct connec-

tion of an external

monitor. Set dipswitch

to OFF when in use.

Hardware Inventory AXIS 2400/2401 Admin Manual

8

AXIS 2400/2401 Rear Panel

Note: The power supply for your AXIS 2400/2401 is country-specific. Please check that the type you

are using is correct. See below.

Hardware Inventory

Check the items supplied with your AXIS 2400/2401 against the following list:

Item Title/Variants Part Numbers Item Title/Variants Part Numbers

Video Server AXIS 2400 0092-001-02 Power Supply

(PS-D) Europe 14233

AXIS 2401 (NTSC) 0103-011-02 UK 14234

AXIS 2401 (PAL) 0103-001-02 Australia 14255

Null Modem Cable - 16954 USA 14253

Warranty Document 18640 Japan 14254

Disk Media AXIS Network

Camera CD v2.0 (or

later)

-This Docu-

ment AXIS 2400/2401

Administration

Manual v2.1

19097

Power Supply Connector

A single Jack socket (PS-D) for

connection of the AXIS 2400/2401

power supply. The terminal block

connector provides an auxiliary

connection point for AC or DC

power to the unit.

Network Connector

The AXIS 2400/2401 is designed for 10 Mbps Ethernet and

100 Mbps Fast Ethernet networks and connects to the net-

work via a standard RJ45 connector. Supporting NWAY,

the AXIS 2400/2401 detects the speed of the local net-

work segment and varies the speed of data communication

accordingly (between 10 Mbps and 100 Mbps).

I/O Terminal Block

The I/O Terminal Block connector is located between the two serial ports on the

rear panel and provides the physical interface to one relay switch output, four

digital photo-coupled inputs, and an RS-485 interface. Use this connector for

transmitting data over multi-drop communication lines, RS-485 Pan Tilt devices,

and external triggering - typically associated with CCTV equipment. The connector

can be utilized as an alternative connection point for DC supply to the unit.

RS-232 Serial Connectors

Two 9-pin D-sub connectors providing RS-232 serial con-

nection. Typically used for Pan/Tilt device interface. COM1

is multiplexed with the RS-485 port via the Terminal

Block Connector. COM2 can also be used for connecting a

modem or the AXIS 2191 Audio Module.

POWER

PS-D COM 1 COM 2 ETHERNET

10/100

1 2 3 4 5 6 7 8

9 10111213141516

AXIS 2400/2401 Admin Manual Installing on a Network 9

Installing on a Network

• Quick installation - Follow the instructions below to quickly install on an Ethernet network.

• Easy installation - See Using the AXIS IP Installer, on page 39.

• Macintosh users - Please refer to Notes for Macintosh Users, on page 38.

❸Using an appropriate method for your operating system, assign your product with a unique IP

address from a computer on your network, as follows:

Note: In some Unix systems, the arp command can be located in a directory that is not on the

command path.

You will now see ‘Request timed out...’ messages repeatedly returned in the window.

❷Note the Serial number on the

underside of the unit. You need to

know this to set the IP address.

❶Connect the video output of your camera(s) to the AXIS 2400/2401

video port(s) using standard 75 Ohm coaxial video cable, terminated

with a BNC-connector. (Use a BNC-to-RCA converter if your camera is

supplied with a standard phono-type (RCA) connector.)

Serial number same as

Ethernet number; e.g.

00408c100086 =

00-40-8c-10-00-86

Windows only - Start a DOS window and type these commands:

Syntax:

arp -s <Server IP address> <Ethernet address> <my PC IP address>

ping -t <Server IP address>

Example:

arp -s 172.21.1.200 00-40-8c-10-00-86 172.21.1.193

ping -t 172.21.1.200

UNIX only - Type this in your command line:

Syntax:

arp -s <IP address> <Ethernet address> temp

ping <IP address>

Example:

arp -s 172.21.1.200 00:40:8c:10:00:86 temp

ping 172.21.1.200

❹Connect an Ethernet cable to the AXIS

2400/2401 and attach it to the network.

Network connector

RJ-45 connector

Installing on a Network AXIS 2400/2401 Admin Manual

10

Verifying and Completing the Installation From Your Browser

Important!

• Upon delivery, the AXIS 2400/01 is configured for open access (anonymous users). The unit is sup-

plied with one pre-configured Administrator username and password, set to root and pass, respec-

tively. The Administrator password must be changed immediately to prevent unauthorized access to

the Admin Tools and/or product images, as defined in the Security Settings.

• To enable the updating of images in Microsoft Internet Explorer, set your browser to allow ActiveX

controls and perform a once-only installation of Axis' ActiveX component onto your workstation. If

your working environment restricts or prohibits the downloading of additional software components,

you can alternatively, from the Image Settings, configure your AXIS 2400/01to use a Java applet for

updating the images. Refer to the online Help for more information.

❼Exit ping. The installation is now complete, and you are ready to

access the AXIS 2400/2401 from your browser, as described in the

next section.

Power Supply

Connector

❺Connect the power supply to the unit and connect

it to your main power supply.

❻Approximately 10-15 seconds after connecting

the power supply, the message ‘Reply from

172.21.1.200...’ - or similar, is returned

within the window. Ensure that the Power Indica-

tor is permanently lit and that the Network Indi-

cator flashes intermittently.

Network Indicator

Power Indicator

❶Start your browser and enter the IP address of the

AXIS 2400/2401 in the location/address field.

❷Click the Installation Wizard. The wizard guides

you through the remaining installation procedures.

AXIS 2400/2401 Admin Manual Installing via the Null Modem Cable 11

Installing via the Null Modem Cable

This section describes how to install the AXIS 2400/01 using the null modem cable. For information

on how to configure the unit for modem operation, please see

Modem Settings,

on page 26.

Important!

Step A - Connecting Your Computer Using the Null Modem Cable

• Although instructions for installing the AXIS 2400/2401 using a null modem cable are provided below, it is

recommended that, wherever possible, the unit is initially installed and configured over a network.

• The information and examples featured here are specific to Windows 2000, but the process is similar in

other versions of Windows. Refer to your system information for further information on creating a Dial-Up

Networking connection if you are using any other operating system.

• Windows Dial-Up Networking and TCP/IP must be correctly installed prior to commencing with the

modem cable connection. Detailed information on how to check this is provided in Windows Help.

❶Connect the supplied Null modem cable

between the COM-2 Serial Connector on

the AXIS 2400/01 and the COM-port on

your computer. ❷Press the Power button

on the front panel and check that the

Power Indicator lights up.

❸From the Start menu, open the

Control Panel and click Phone and

Modem Options. Select Modems.

❹If a Standard Modem is already set up, you

should proceed directly to the next page. If no

modem is installed, click Add and go to step 5.

❻Select the Standard 28800

modem from the displayed list

of modems. Click Next>.

❺Check the box: Don’t detect my modem,

I will select it from a list. Click Next>.

❽A standard 28800 modem connection

is now available for the AXIS 2400/01.

Click Finish to complete the installation.

❼Select the serial port to which your

AXIS 2400/01 is now connected via the

Null Modem cable. Click Next>.

Installing via the Null Modem Cable AXIS 2400/2401 Admin Manual

12

Step B - Creating a Dial-Up Networking Connection

Follow the steps below to create a Dial-Up networking connection to the AXIS 2400/2401:

❶Click the Start button, Settings, Network

and Dial-up Connections, and finally, Make

New Connection. Click Next> when the

Wizard starts.

❷Set the type of connection as

Dial-up to Private Network. Click

Next.

❹Provide the connection with a

name (Axis in our example) and

then click Finish.

❸A telephone number is requested

in this dialog, but as it won’t actually

be used, simply enter any dummy

number. Click Next>.

AXIS 2400/2401 Admin Manual Installing via the Null Modem Cable 13

Verifying the Modem Connection and Completing the Installation

Having initiated your dial-up connection, as described above, you can quickly test it by

accessing the AXIS 2400/2401 from a browser (Netscape 4.x or Internet Explorer 4.x/5.x)

as follows:

❺After clicking Finish in the Network

Connection Wizard, the Dial-up dialog

opens. Click Properties.

❻Select the installed modem and

click Configure.

❽Finally, enter the default User

name Root and the password

pass. Click Dial.

❼Set the Maximum Speed to 115200

bps. Click OK twice to get back to the

dial-up dialog.

❶Since the AXIS 2400/2401 emulates a DNS

server, you can type in any URL (containing a

period) in the Location/Site field of your

browser, as shown here.

❷Click the Installation Wizard. The wizard guides

you through the remaining installation procedures.

my.2400

Configuring the Video Server AXIS 2400/2401 Admin Manual

14

Configuring the Video Server

After deciding on the application you wish to develop and having installed your AXIS

2400/2401, the unit is now either connected directly to a local area network, or connected

to a local PC using the supplied Null Modem Cable.

This section describes how to configure the AXIS 2400/2401 and is intended specifically

for product Administrators – who normally have high-level privileges denied to ordinary

users.

The AXIS 2400/2401 is configured from a standard browser (Netscape Navigator 4.x or

Microsoft Internet Explorer 4.x/5.x), by using the Administration Tools.

Important!

The Administration Tools

The Web-based Administration tools are displayed in an intuitive graphical user interface

that allows simple point-and-click system configuration. How to access and use the tools is

explained in the following pages.

Tip! On-line help is available on every page of the AXIS 2400/2401Web interface.

This information is of particular relevance when configuring the unit and should be used as a

first point of reference for resolving any administration queries. The help system is stored

internally in the unit.

Accessing the Tools

Follow the instructions below to access the Administration Tools from a browser:

1. Start the browser and enter the name or IP address of the AXIS 2400/2401 in the

location/address field.

Example!

2. The Application page is now displayed. Click the Admin button to display the

Administration Overview page and the Administration Tools.

To access the AXIS 2400/2401 configuration pages, you must first set the IP address, as described in

Installing on a Network, on page 9.

http://172.21.1.200/

AXIS 2400/2401 Admin Manual Configuring the Video Server 15

3. The various components of the video server are shown as icons on the page. Simply

click the desired component and configure it directly from here.

Important!

• If this is the first time you have accessed the AXIS 2400/2401, the Welcome page will be now be dis-

played. Click the button for the Installation Wizard and configure your application.

• To enable the updating of images in Microsoft Internet Explorer, set your browser to allow ActiveX

controls and perform a once-only installation of Axis' ActiveX component onto your workstation. If

your workstation restricts the downloading of additional software components, you can alternatively

configure your AXIS 2400/2401 to use a Java applet for updating the images.

•Administrators can choose not to display the Administration and other navigational buttons from the

user interface. Selecting this feature ultimately means that the Administration tools can then only be

accessed by entering the full Admin address into the browser’s URL field; for example:

http://172.21.1.200/admin/.

Configuring the Video Server AXIS 2400/2401 Admin Manual

16

Admin Tools - Overview

The Administration Tools provide access to the following tools and parameters:

COM Port

Installation Wizard

Application Wizard

General

Network

Pan Tilt

Date and Time

Specify the system settings for the supported networking protocols, including:

TCP/IP (Network settings), DNS (Domain Name System Settings) and SMTP (E-Mail

Settings). Also provides access to the settings for Dynamic IP Address Notification

Set server parameters to factory default.

Define the user name and password

for administratrors and users.

Restart the AXIS 2400/2401.

These 4 buttons show various

product information.

Set the system date & time,

manually or automatically.

Sets all of the parameters required for securely viewing images directly in a browser;

including: TCP/IP (Network), SMTP (e-mail), Date/Time, and System Security settings.

Use the Application Wizard for developing the following applications:

• transmitting images to a remote server on your network

• sending e-mails with embedded images, or links to recorded video streams

• developing alarm or time-based image applications

Define the type of modem you want to use

and specify the flow control, initialization

string and other settings. (COM2 only).

Video

(with or without

Set the image features; such as: display-

ing text, clock, color, Black & White etc.

Define the video transmission standard,

automatically or manually.

Create and recall Pan Tilt and Zoom pre-

set conditions (only visible if the video

source is connected to a pan tilt device).

Image

Input/Modulation

Video

Preset Positions

Choose your default viewer and personal settings.

Security

Layout

Modem Configure the connec-

tion to your ISP and edit

PPP-scripts.

Pan/Tilt)

Refine the Driver Specific Settings. (Only

visible if the video source is connected

to a pan tilt device).

Driver Specific

Settings

Use and configure the AXIS 2191 Audio Mod-

ule (COM2 only). See also Installing the Audio

Module, on page 33.

Select a pan tilt device. Note: This icon is dis-

played under a Serial Port icon only if the pur-

pose of the serial port is defined as Pan Tilt.

Audio

AXIS 2400/2401 Admin Manual Configuring the Video Server 17

Designing your Application

Using the Wizards

Click the Admin Overview button and use the Wizards (explained below) to quickly

establish the parameters necessary for an application:

Wizard Type Parameters / Options Description

❶Installation Wizard

Sets all of the parameters

required for securely

viewing images directly in a

browser.

Users Define or edit the Administrator password (the Administrator user name is

permanently set to root, and the default password is set to pass), or define,

add and delete user names and passwords.

TCP/IP Specify the IP Address for your AXIS 2400/2401. If you intend to use DNS

names, specify the Domain Name and the IP-addresses for the primary and

secondary DNS servers. You may also optionally specify a Host Name for

the AXIS 2400/2401. There is also an option for restricting the network

bandwidth usage and for selecting the appropriate media.

Date and Time Synchronize the internal clock of the AXIS 2400/2401. This can be done

manually or automatically, from an NTP server or your computer clock.

There is also an option that automatically adjusts the time for daylight

saving.

Image Settings Choose monochrome or color images, and define the quality of the images.

Remember: the higher the quality of the images - the greater the file sizes

and the network bandwidth requirements.

Video Modulation Detection of the type of video modulation used.

❷Application Wizard

Use this wizard to develop

applications for:

• transmitting images to

a remote server on your

network

• sending e-mails with

embedded images or

links to recorded video

streams, and/or devel-

oping alarm or

time-based image

applications

Video Sources

Upload

Specify the video sources to which the settings made in the wizard will

apply. Proceed to define how and when your images will be transmitted,

by choosing to either:

• upload images continuously, or

• upload images only when an alarm event occurs.

Alarms, buffers,

and destination Depending upon the choice of application made above, continue with the

wizard to define:

• digital input alarm conditioning

• pre- and post-alarm buffer settings

• the network protocol to use for upload

• SMTP settings and the e-mail recipient (if appropriate)

• FTP path name and security settings (if used)

Refer to the appropriate settings page for full details on each of the above

parameters.

Configuring the Video Server AXIS 2400/2401 Admin Manual

18

Tip!

General Server Settings

Click the Video Server icon to display and/or edit the following settings:

Date and Time

Click the Date and Time icon to set the date and time, automatically, or manually.

Automatic setting of the date and time requires you to either synchronize the time with

that on your computer or, alternatively, to provide the IP address of an NTP server. To

automatically adjust the time to reflect changes made by daylight saving, check the box

provided. Click Save to register the settings with the Video Server.

Security

To prevent unauthorized use of the Video Server, access is password-protected and

restricted to defined Users and Administrators only. Administrators have unrestricted

access to the Administration Tools and can determine the registration of all other users.

As an Administrator, click the Security icon to either:

• define or edit the Administrator password (the Administrator user name is permanently set to

root, with the default password set to pass)

• configure, add or delete user names and passwords

Important!

By default, the AXIS 2400/2401 supports anonymous user access, which means that

anybody on the Internet/intranet has access to the video images and Admin Tools from a

browser. Entering at least one user name and password for an authorized user in the

Security page will disable anonymous access, and thereafter only allow defined users. If

the anonymous user service is satisfactory for your application, do not add any users. The

Administrator password should, however, still be changed.

Having used the Wizards for initially configuring your application, refer to the on-line Help and use the

Administration Tools for refining the application to meet your specific requirements.

Upon delivery, the AXIS 2400/2401 is configured for open access (anonymous users), with one

pre-configured Administrator user name and password, set to root and pass, respectively. The Adminis-

trator password should always be changed, to prevent unauthorized access to the Admin Tools and/or

product images. Furthermore, all Axis products are supplied with these defaults.

AXIS 2400/2401 Admin Manual Configuring the Video Server 19

Layout Settings

Using the Layout settings, you can define your default viewer and enable a wide range of

personal features for inclusion on the product’s Home Page.

Default viewer for Internet Explorer

To enable the updating of images in Microsoft Internet Explorer, you must set your

browser to allow ActiveX controls and perform a once-only installation of the Axis

ActiveX component onto your workstation. If your computer restricts the downloading of

additional software components, you can instead configure your AXIS 2400/2401 to use a

Java applet for updating the images. Click the appropriate button for your choice and then

click OK.

Personal Settings

Many of the features on the Home page can be customized. For example, you can quickly

change the background color and include your corporate logo by clicking the appropriate

radio buttons and providing the appropriate URL for any given object.

Refer to the on-line help for more information on personal settings.

Caution!

View Parameter List

The Parameter List provides a comprehensive list of all of the system parameters and their

current settings. Click View Parameter List to display the list.

View Log File

System messages are recorded in a single log file and stored in product memory.

Consequently, the file can be used for examining system events. The log file also serves as

a useful diagnostic tool when attempting to resolve any problem that might occur. See also

Troubleshooting, on page 40.

To display the latest server messages since the last Restart of the system, click the View

Log File button.

View Server Report

This button shows important information about the server status and settings.

View Release Notes

This button opens a window showing the release notes for the installed firmware.

Unchecking the Show Admin box removes the Admin button from the product Home Page, and effec-

tively means that the Administration Tools can then only be accessed by entering the full Admin address

into the browser’s URL-field; for example: http://172.21.1.200/admin/.

Configuring the Video Server AXIS 2400/2401 Admin Manual

20

Emergency Actions

In certain circumstances it may become necessary to perform a Restart of the AXIS

2400/2401, or to return it to its Factory Default settings. Both of these actions can be

performed by clicking the appropriate button on this page. Please see Reinstating the

Factory Default Settings, on page 27, for details of how to reset to the factory default.

Network Settings

Click the Network icon to display, edit and refine the settings for:

•TCP/IP - used by the Video Server for transmitting data over the network.

•DNS (Domain Name System) - the Internet service used by the product for translating

domain names into IP addresses.

•SMTP (E-mail) - this is the protocol for sending e-mail messages between mail servers on the

network.

•Miscellaneous - set the network media and to restrict the bandwidth used by the product.

Configure the Network Settings with reference to the on-line help and the table below:

TCP/IP Parameters Description

DHCP Enable DHCP to allow centralized assignation of IP addresses. Requires a DHCP server on the network.

BOOTP Enable the BOOTP protocol for setting the IP address automatically. For further information on using

BOOTP, see Other IP Setup Methods, on page 38. If you intend to use the AXIS IP Installer, BOOTP must be

enabled.

IP address Specifies the unique 32-bit IP address of your unit.

Default Router Specifies the network router your video server will use.

Subnet Mask If unsure what value to use, contact your system administrator.

Host Name If you are using a DNS server on your network (see below), this is usually the same as the assigned DNS

Name.

DNS Parameters Description

Domain Name Enter the name of the domain your AXIS 2400/2401 belongs to.

Primary DNS Defines the IP address of the primary DNS server. This is used for identifying a computer by name instead

of IP address.

Secondary DNS The IP address of the secondary DNS server. This will be used if the primary DNS server is unavailable.

SMTP Parameters Description

Primary Mail Server Defines the server that provides your mail facilities.

Secondary Mail Server Defines a secondary server that can provide mail facilities in the event of the primary server being

unavailable.

Return Address The reply address for e-mails sent by the AXIS 2400/2401; that is, the name that will appear in the ‘From’

field of the dispatched e-mail.

Miscellaneous Description

Select Media This does not normally need to be changed, but if you have specific needs - due to the use of network

switches or similar equipment, select the type of network media here.

Max Bandwidth With the default set to unlimited, this parameter defines a restriction on the network bandwidth used by

the video server; particularly useful for a connection to a busy network.

HTTP Port Number This does not normally need to be changed, but may be, if you have particular requirements.

La page charge ...

Axis 2400/01 Manuel utilisateur

Ce manuel convient également à

Axis 2400/01 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents