OBD1100
en User guide
fr Mode d’emploi
es Guía del usuario
ABS, OBDII, and CAN Scan Tool
Analyseur-contrôleur ABS, OBD II et CAN
Herramienta de escaneo ABS, OBDII
2 | Operating instructions | OBD 1100 |en
574114 REV B | 08.2018 Bosch Automotive Service Solutions
Table of Contents
Safety Precautions ......... 3
Signal Words and Symbols . 3
Important Safety Messages .. 3
About the Tool ............ 4
Tool Parts ................ 4
Icons .................... 4
Connect the Tool .......... 5
Diagnostic Menu User
Interface ................. 5
Read Codes ............... 6
Vehicle Selection .......... 7
Erase Codes .............. 7
MIL Status ................ 7
I / M Monitors (Emissions) ... 8
View Freeze Data .......... 9
VIN ...................... 9
System Setup ............. 9
View Data ................ 9
Troubleshooting .......... 10
PID Denitions ........... 10
Limited Warranty ......... 15
Disclaimer ............ 15
Software. . . . . . . . . . . . . . 15
Technical Support / Repair
Service .............. 15
Français ................ 16
Español ................. 32
| OBD 1100 | Operating instructions | 3en
574114 REV B | 08.2018Bosch Automotive Service Solutions
Safety Precautions
This user guide describes the
features of the tool and provides
step-by-step instructions for
operating the tool. Always refer
to and follow safety messages
and test procedures provided by
the manufacturer of the vehicle
and the tool.
Read and understand
the user guide before
operating the tool.
An undetected or uncorrected
vehicle malfunction could cause
a serious, even fatal, accident.
Important safety information in
this user guide is intended to
protect the user, bystanders, and
the vehicle.
Signal Words and Symbols
WARNING!
Indicates a possible
hazardous situation
that, if not avoided,
could result in death
or serious injury to op-
erator or bystanders.
NOTICE
Indicates a condition
that may result in lost
information.
BIndicates a single-
step procedure.
Important Safety
Messages
WARNING!
This tool may not
detect every malfunc-
tion. Do not take
chances with brakes,
steering, or other vital
functions of the vehi-
cle. A serious accident
could result.
Always wear ANSI-
approved goggles for
eye protection.
• Before testing a vehicle, make
sure the transmission is in
PARK (automatic transmis-
sion) or NEUTRAL (manual
transmission) and the parking
brake is set.
• Never lay tools on the vehi-
cle battery.
• Battery acid can burn. If
contacted, rinse with water
or neutralize with a mild
base such as baking soda. If
you splash your eyes, ush
with water and call a physi-
cian immediately.
• Never smoke or have open
ames near vehicle. Vapors
from gasoline and battery
are explosive.
4 | Operating instructions | OBD 1100 |en
574114 REV B | 08.2018 Bosch Automotive Service Solutions
• Do not use the tool if internal
circuitry has been exposed
to moisture. Internal shorts
could cause a re and dam-
age the vehicle or tool.
• Always turn the ignition
key OFF when connecting
or disconnecting electrical
components unless other-
wise instructed.
• Most vehicles are equipped
with airbags. Follow vehicle
service manual precautions.
Serious injury or death
could result from an unin-
tended deployment.
WARNING!
A vehicle airbag can
open for several min-
utes after the ignition
has been turned off.
• Always follow vehicle manu-
facturer’s warnings, cautions,
and service procedures.
About the Tool
The tool allows you to retrieve
and erase / reset diagnostic data
from the vehicle control module.
The diagnostic data can be used
to help determine the cause of a
vehicle malfunction.
Use the tool to perform the fol-
lowing functions:
Codes / Data Erase / Reset Retrieve
Confirmed Codes Erase •
Pending Codes Erase •
Permanent Codes — •
View Data — •
MIL Status — •
I / M Monitors Reset •
View Freeze Data Erase •
VIN (Vehicle Identifi-
cation Number) — •
Tool Parts
Part Description
LCD
display 8 line by 21 character mono-
chrome LCD.
READ
Performs the Read Codes func-
tion and scrolls back through
the screens. Press this key when
an up arrow (#) appears on the
display.
ERASE
Performs the Erase Codes func-
tion and scrolls forward through
the screens. Press this key when
a down arrow ($) appears on
the display.
ENTER Selects displayed item.
BACK Returns to the previous screen.
OBD II
Connector Connects the tool to the vehicle
connector.
Icons
Icon Description
$
Indicates additional informa-
tion is available on next screen
by using the ERASE key.
#
Indicates additional information
is available on previous screen
by using the READ key.
CONFIRMED Confirmed codes are reported
when a component is indicat-
ing a malfunction is present.
| OBD 1100 | Operating instructions | 5en
574114 REV B | 08.2018Bosch Automotive Service Solutions
PENDING
Pending codes are reported
when a problem occurs during
the current or last completed
drive cycle.
PERMANENT Permanent codes are a special
type of confirmed code that
only the vehicle can erase.
x / y
Appears only when view-
ing codes. Indicates code se-
quence and quantity (code x
of y). For example, “2 / 9” indi-
cates that the 2nd of 9 codes
reported by the computer mod-
ule is being viewed.
ABS $##
Mod $##
Appears only when viewing
codes. Indicates the computer
module that reported the code.
ABS will appear if the code is
an ABS code. Mod $## appears
when the code is a powertrain
code. The Mod $## is the name
assigned to the vehicle control
module reporting the code.
Indicates that the READ and
ERASE hot keys are active
Connect the Tool
To connect the tool to the vehicle:
1. Locate the OBD II connector
under the steering column. If
the connector is not there, a
label should be there indicat-
ing the whereabouts of the
connector. For more informa-
tion on OBD II connectors, go
to http://www.obdclearing-
house.com/oemdb.
2. If necessary, remove the cover
from the vehicle connector.
3. Turn the ignition switch to
the ON position. Do not start
the engine.
4. Plug the OBDII connector
attached to the tool into the
vehicle connector.
The Tool automatically reads
Codes and displays the data.
When done viewing data,
press
ENTER key to return
to Diagnostic Menu.
NOTICE
If the vehicle returns a
manufacturer specic
code, the tool will ask
if you wish to select
the vehicle and then
read ABS codes.
If the vehicle doesn’t
return a manufacturer
specic code, the tool
will ask if you wish
to select a vehicle to
read ABS codes. ABS
is not supported for
all vehicles.
Diagnostic Menu User
Interface
To select functions:
1. From the Diagnostic Menu,
press the READ or ERASE
arrow key until the desired
function is highlighted, then
press
ENTER to retrieve and
display the results.
6 | Operating instructions | OBD 1100 |en
574114 REV B | 08.2018 Bosch Automotive Service Solutions
DIAGNOSTIC MENU
====================
Read Codes
Erase Codes
MIL Status
View Data
View Freeze Data
^^
VIN
2. When complete, press
BACK to return to the
Diagnostic Menu selec-
tion screen.
Read Codes
To read the codes:
BPress and hold the
READ key for 2 sec-
onds then release it, or
Select Read Codes from
Diagnostic Menu.
If ABS is supported for your vehi-
cle, a menu is shown to select
either OBDII/EOBD, or ABS.
Select ABS to read ABS codes,
and OBDII/EOBD to read emis-
sions related powertrain codes.
For codes other than ABS codes,
the tool displays Conrmed,
Pending, and Permanent Codes.
Conrmed Trouble Codes are
reported when a component,
sensor, or other part of the
vehicle is indicating a malfunc-
tion is present. The malfunction
must be present for a sufcient
amount of time before the vehi-
cle records and the Tool displays
a Conrmed Trouble Code.
Conrmed codes are indicated
by the CONFIRMED icon.
Pending Codes are only reported
if a problem occurs during the
current or last completed drive
cycle. Pending Codes do not nec-
essarily indicate a faulty compo-
nent or system. Pending Codes
convert to Conrmed Trouble
Codes when an emissions prob-
lem persists long enough to be
considered a real problem, not
an anomaly. Pending Codes are
indicated by a PENDING icon.
Permanent Codes are special
conrmed codes. Permanent
Codes began being reported by
vehicles beginning around 2010,
so they are not supported by
every vehicle. While Conrmed
Codes can be erased by the
tool, Permanent Codes cannot.
Permanent Codes are erased by
the vehicle when the vehicle has
determined the fault is no longer
present. Permanent Codes are
indicated by a PERMANENT icon.
| OBD 1100 | Operating instructions | 7en
574114 REV B | 08.2018Bosch Automotive Service Solutions
Vehicle Selection
Vehicle Selection will be dis-
played for Read Codes when a
manufacturer specic DTC is
retrieved from the vehicle.
Erase Codes
The Erase function performs
the following:
9Erases codes (both
Conrmed and Pending
DTCs) when erasing OBDII/
EOBD codes. Permanent
codes can only be erased by
the vehicle.
9May erase Freeze Data results
depending on the vehcle.
9Sets I / M Monitors to
not ready.
NOTICE
Perform Erase Codes
function only after
systems have been
checked completely
and DTCs have been
written down.
To erase codes from the vehi-
cle computer:
1. Set the ignition to Key On
Engine Off. Do NOT start the
vehicle. The engine should
not be running.
2. Press and hold the ERASE
key for 3 seconds then
release, or select Erase
Codes from Diagnostic Menu;
press
ENTER.
3. When the conrmation mes-
sage appears on the display,
choose one of the follow-
ing options.
• To proceed with the opera-
tion: Press
ENTER for YES.
• To cancel the operation and
return to the Diagnostic
Menu: Press BACK for NO.
4. If ABS is supported for your
vehicle, a menu is shown to
select either OBDII/EOBD,
or ABS. Select ABS to erase
ABS codes, and OBDII/EOBD
to erase emissions related
powertrain codes.
The Tool will automatically per-
form the Read Codes function
after erasing codes. The Tool
will then indicate the number of
codes remaining.
NOTICE
If after erasing codes
a DTC returns, the
problem has not been
xed or other faults
are present.
MIL Status
MIL (Malfunction Indicator
Lamp) status indicates if the
8 | Operating instructions | OBD 1100 |en
574114 REV B | 08.2018 Bosch Automotive Service Solutions
vehicle computer is telling the
MIL to illuminate when the
engine is running.
• MIL ON indicates that the
Malfunction Indicator Lamp
should be ON.
• MIL OFF indicates that the
Malfunction Indicator Lamp
should be OFF.
I / M Monitors (Emissions)
Inspection / Maintenance
Monitors provide a snapshot
of the Emission System opera-
tions by indicating that the
I / M Monitors are Ready or Not
Ready. For an I / M Monitor to
be Ready, the vehicle must have
completed a drive cycle (been
driven long enough under proper
conditions to have completed a
drive cycle). A Monitor must be
listed as Ready to pass an emis-
sions test. If an I / M Monitor is
Not Ready, it is because a drive
cycle has not completed.
The Tool will indicate Ready
(ok), Not Ready (inc), or Not
Applicable (n/a) for each I / M
Monitor. The Tool supports the
following I / M Monitors:
Monitor Expanded Name
Misfire Monitor Misfire Monitor
Fuel System Mon Fuel System Monitor
Comp Component Comprehensive Compo-
nents Monitor
Catalyst Mon Catalyst Monitor
Htd Catalyst Heated Catalyst Monitor
Evap System Mon Evaporative System Mon-
itor
Sec Air System Secondary Air System
Monitor
A/C Refrig Mon Air Conditioning Refriger-
ant Monitor
Oxygen Sens Mon Oxygen Sensor Monitor
Oxygen Sens Htr Oxygen Sensor Heater
Monitor
EGR/VVT Sys Mon
Exhaust Gas Recircula-
tion or Variable Valve Tim-
ing Monitor
NMHC Cat Mon Non-Methane Hydrocar-
bon Catalyst
NOX Treat Mon Nitrogen Oxide Treatment
Boost Pres Mon Boost Pressure Monitor
Exhst Gas Sensr Exhaust Gas Sensor
PM Filter Mon Particulate Matter Filter
This is a complete list of I / M
Monitors supported by the Tool.
The number of Monitors read
by the Tool from your vehicle
may vary. A diesel vehicle, for
example, does not have an
Oxygen Sensor Monitor. As a
result, there will be no Oxygen
Sensor Monitor status for a die-
sel vehicle.
Two types of I / M Monitors
tests are:
| OBD 1100 | Operating instructions | 9en
574114 REV B | 08.2018Bosch Automotive Service Solutions
Since DTCs Cleared - shows
status of the monitors since
the DTCs were last erased.
This Drive Cycle - shows
status of monitors since the
start of the current drive
cycle. Refer to the vehicle
service manual for more
detailed information on
emission-related monitors
and their status.
9Some vehicles do not sup-
port This Drive Cycle. If
vehicle supports both types
of monitors the I / M Monitors
Menu displays.
View Freeze Data
Displays a snapshot of operat-
ing conditions at the time the
Diagnostic Trouble Code was
created. See PID Denitions for
more information.
VIN
The VIN function allows the
tool to request the vehicle’s
VIN number.
The VIN function applies to
model year 2000 and newer OBD
II compliant vehicles.
System Setup
System Setup allows:
• Display contrast to
be changed
• Tool information to be viewed
• Display to be checked
• Operation of the keypad to
be checked
• Memory of the Tool to
be checked
• Units of measure to
be changed
View Data
The View Data function allows
real time viewing of the vehicle’s
computer module’s PID data.
As the computer monitors the
vehicle, information is simultane-
ously transmitted to the Tool.
View Data allows the following
items to be viewed on the Tool:
Sensor data
Operation of switches
Operation of solenoids
Operation of relays
Multiple PIDs may be sent if vehi-
cle is equipped with more than
one computer module (for exam-
ple a powertrain control mod-
ule [PCM] and a transmission
control module [TCM]. The Tool
identies them by their iden-
tication names (ID) assigned
by manufacturer (i.e. $10 or
$1A). See PID Denitions for
more information.
10 | Operating instructions | OBD 1100 |en
574114 REV B | 08.2018 Bosch Automotive Service Solutions
Troubleshooting
If a “LINK ERROR” message
appears, cycle the ignition
key to the OFF position for
10 seconds, then back ON,
then press the
ENTER
key. Make sure the ignition
key is in the ON not the
ACCESSORY position.
If the MIL Status is ON and
the MIL is not illuminated
with the engine running,
then a problem exists in the
MIL circuit.
PID Denitions
NOTICE
Although over 300
PIDS are available,
the tool only displays
the PIDs the vehicle
supports.
PID PID description
ABS FRP Absolute Fuel Rail Pressure
ABS LOAD Absolute Load Value
ABS TPS B, C Throttle Position B, C
ABSLT TPS Absolute Throttle Position
ACC POS D Accelerator Pedal D, E, F
ACC POS REL Relative Accelerator Pedal
Position
AECD1_TI-
ME1, TIME 2
Total Run Time with EI-AECD
#1 Timer 1 Active, #2 Timer
Active
AECD10_TI-
ME1, TIME 2
Total Run Time with EI-AECD
#10 Timer 1 Active, #2 Timer
Active
PID PID description
AECD11_TI-
ME1, TIME 2
Total Run Time with EI-AECD
#11 Timer 1 active, #2 Timer
Active
AECD12_TI-
ME1, TIME 2
Total Run Time with EI-AECD
#12 Timer 1 active, #2 Timer
Active
AECD13_TI-
ME1, TIME 2
Total Run Time with EI-AECD
#13 Timer 1 active, #2 Timer
Active
AECD14_TI-
ME1, TIME 2
Total Run Time with EI-AECD
#14 Timer 1 active, #2 Timer
Active
AECD15_TI-
ME1, TIME 2
Total Run Time with EI-AECD
#15 Timer 1 active, #2 Timer
Active
AECD16_TI-
ME1, TIME 2
Total Run Time with EI-AECD
#16 Timer 1 active, #2 Timer
Active
AECD17_TI-
ME1, TIME 2
Total Run Time with EI-AECD
#17 Timer 1 active, #2 Timer
Active
AECD18_TI-
ME1, TIME 2
Total Run Time with EI-AECD
#18 Timer 1 active, #2 Timer
Active
AECD19_
TIME1, TIME 2
Total Run Time with EI-AECD
#19 Timer 1 active, #2 Timer
Active
AECD2_
TIME1, TIME 2
Total Run Time with EI-AECD
#2 Timer 1 Active, #2 Timer
Active
AECD20_
TIME1, TIME 2
Total Run Time with EI-AECD
#20 Timer 1 active, #2 Timer
Active
AECD3_
TIME1, TIME 2
Total Run Time with EI-AECD
#3 Timer 1 Active, #2 Timer
Active
AECD4_
TIME1, TIME 2
Total Run Time with EI-AECD
#4 Timer 1 Active, #2 Timer
Active
AECD5_
TIME1, TIME 2
Total Run Time with EI-AECD
#5 Timer 1 Active, #2 Timer
Active
AECD6_
TIME1, TIME 2
Total Run Time with EI-AECD
#6 Timer 1 Active, #2 Timer
Active
AECD7_
TIME1, TIME 2
Total Run Time with EI-AECD
#7 Timer 1 Active, #2 Timer
Active
| OBD 1100 | Operating instructions | 11en
574114 REV B | 08.2018Bosch Automotive Service Solutions
PID PID description
AECD8_
TIME1, TIME 2
Total Run Time with EI-AECD
#8 Timer 1 Active, #2 Timer
Active
AECD9_
TIME1, TIME 2
Total Run Time with EI-AECD
#9 Timer 1 Active, #2 Timer
Active
ALCOHOL Alcohol Fuel Percent
BARO PRS Barometric Pressure
BAT_PWR Hybrid Battery Pack Remain-
ing Life
BP_A_ACT, B_
ACT Boost Pressure Sensor A, Sen-
sor B
BP_A_CMD,
B_CMD Commanded Boost Pressure
A, Pressure B
BP_A_STAT, B_
STAT Boost Pressure A Control Sta-
tus, B Control Status
CACT 11, 12 Charge Air Cooler Temper-
ature Bank 1 Sensor 1 sup-
ported, Sensor 2 supported
CACT 21,22 Charge Air Cooler Temper-
ature Bank 2 Sensor 1 sup-
ported, Sensor 2 supported
CALC LOAD Calculated Engine Load
CAT TEMP11,
TEMP12 Cataltic Converter Temp
Bank1, Temp Bank 3
CAT TEMP21,
TEMP22 Cataltic Converter Temp
Bank2, Temp Bank 4
CLR DIST Distance since erase
CLR TIME Minutes Run since Erase
CLR TRPS Warmups Since Erase
CMD EQ RAT Commanded Equivalence
Ratio
COOLANT Engine Coolant Temp
DPF_REG_
AVGD
Average Distance Between
DPF Regen
DPF_REG_
AVGT
Average Time Between DPF
Regen
DPF_REG_
STAT Diesel Particulate Filter (DPF)
Regen Status
DPF_REG_TYP Diesel Particulate Filter (DPF)
Regen Type
DPF_REGEN_
PCT Normalized Trigger for DPF
Regen
PID PID description
DPF1_DP,
DPF2_DP
Diesel Particulate Filter (DPF)
Bank 1 Delta Pressure Bank 2
Delta Pressure
DPF1_INP,
DPF2_INP
Diesel Particulate Filter (DPF)
Bank 1 Inlet Pressure, Bank 2
Inlet Pressure
DPF1_INT,
DPF2_INT
DPF Bank 1 Inlet Temperature
Sensor, Bank 2 Inlet Tempera-
ture Sensor
DPF1_OUTP,
DPF2_OUTP
Diesel Particulate Filter (DPF)
Bank 1 Outlet Pressure,
Bank 2 Outlet Pressure
DPF1_OUTT,
DPF2_OUTT
DPF Bank 1 Outlet Temper-
ature Sensor, Bank 2 Outlet
Temperature Sensor
ECT 1, 2 Engine Coolant Temperature
1, Temperature 2
EGR CMD Comanded EGR
EGR ERR Exhaust Gas Recirculation
Error
EGR_A_ACT,
B_ACT Actual EGR A Duty Cycle / Posi-
tion, B Duty Cycle / Position
EGR_A_CMD,
B_CMD
Commanded EGR A Duty
Cycle / Position, B Duty Cycle /
Position
EGR_A_ERR,
B_ERR EGR A Error, B Error
EGRT 11, 21 Exhaust Gas Recirculation
Temperature Bank 1 Sensor 1,
Bank 2 Sensor 1
EGRT 12, 22 Exhaust Gas Recirculation
Temperature Bank 1 Sensor 2,
Bank 2 Sensor 2
EGT 11, 21 Exhaust Gas Temperature
(EGT) Bank 1 Sensor 1, Bank
2 Sensor 1
EGT 12, 22 Exhaust Gas Temperature
(EGT) Bank 1 Sensor 2, Bank
2 Sensor 2
EGT 13, 23 Exhaust Gas Temperature
(EGT) Bank 1 Sensor 3, Bank
2 Sensor 3
EGT 14, 24 Exhaust Gas Temperature
(EGT) Bank 1 Sensor 4, Bank
2 Sensor 4
EMIS_SUP Emission requirements to
which vehicle is designed
ENG RUN Time Since Engine Start
12 | Operating instructions | OBD 1100 |en
574114 REV B | 08.2018 Bosch Automotive Service Solutions
PID PID description
ENG SPEED Engine RPM
EOT Engine Oil Temperature
EP_1, 2 Exhaust Pressure Sensor Bank
1, Bank 2
EQ RATIO Equivalence Ratio
EVAP PURGE Commanded EVAP Purge
EVAP VP EVAP Vapor Pressure
EVAP VPA Absolute EVAP Vapor Pressure
FRP_A, B Fuel Rail Pressure A, B
FRP_A_CMD,
B_CMD Commanded Fuel Rail Pres-
sure A, B
FRT_A, B Fuel Rail Temperature A, B
FUEL LEVEL Fuel Level Input
FUEL PRES Fuel Rail Pressure
FUEL SYS 1, 2 Fuel System 1 Loop Status,
System 2 Loop Status
FUEL TYPE Fuel Type
FUEL_RATE Engine Fuel Rate
FUEL_TIMING Fueling Injection Timing
GPL_STAT Glow Plug Lamp Status
IAF_A_CMD,
B_CMD Commanded Intake Air Flow A
Control, B Control
IAF_A_REL, B_
REL Relative Intake Air Flow A
Position, B Position
IAT Intake Air Temp
IAT 11, 21 Intake Air Temperature Sen-
sor Bank 1 Sensor 1, Bank 2
Sensor 1
IAT 12, 22 Intake Air Temperature Sen-
sor Bank 1 Sensor 2, Bank 2
Sensor 2
IAT 13, 23 Intake Air Temperature Sen-
sor Bank 1 Sensor 3, Bank 2
Sensor 3
ICP_A, B Injection Control Pressure
A, B
ICP_A_CMD,
B_CMD Commanded Injection Control
Pressure A, B
IDLE_TIME Total Idle Run Time
IGN ADV Timing Advance
PID PID description
LAMBDA11,
21 02 Sensor Lambda Bank 1
Sensor 1, Bank 2 Sensor 1
LAMBDA12,
22 02 Sensor Lambda Bank 1
Sensor 2, Bank 2 Sensor 2
LT FTRM1 Long Term Fuel Trim 1 or 3
LT FTRM2 Long Term Fuel Trim 2 or 4
LT SEC FT1,
2, 3, 4 Long Term Secondary O2 Sen-
sor Fuel Trim 1, 2, 3, 4
MAF, A, B Mass Air Flow, A, B
MAP, A, B Manifold Absolute Pressure,
A, B
MIL DIST MIL_DIST
MIL STATUS Malfunction Indicator Lamp
MIL TIME Minutes Run by MIL activated
MST Manifold Surface Temperature
N/D_STAT Auto Trans Neutral Drive
Status
N/G_STAT Manual Trans Neutral Gear
Status
NNTE_Stat NOx NTE control area status
NOX 11, 21 NOx Sensor Concentration
Bank 1 Sensor 1, Bank 2 Sen-
sor 1
NOX 12,22 NOx Sensor Concentration
Bank 1 Sensor 2, Bank 2 Sen-
sor 2
NOX LEVEL
HI, HI1, HI2,
HI3, HI4
SCR inducement system
actual state 10K history HI1
(0-10000 km), 10K history HI2
(10000-20000 km), 10K his-
tory HI3 20000-30000 km),
10K history HI4 (30000-
40000 km): NOx emission
too high
NOX_ADS_DE-
SUL NOx Adsorber Desulfuriza-
tion Status
NOX_ADS_RE-
GEN NOx Adsorber Regen Status
NWI_TIME Total Run Time by the Engien
whicle NOx warning mode is
activated
O2S O2 Voltage or Current indi-
cates Bank / Sensor
O2S11_PCT,
O2S21_PCT
02 Sensor Concentration
Bank 1 Sensor 1, Bank 2 Sen-
sor 1
| OBD 1100 | Operating instructions | 13en
574114 REV B | 08.2018Bosch Automotive Service Solutions
PID PID description
O2S12_PCT,
O2S22_PCT
02 Sensor Concentration
Bank 1 Sensor 2, Bank 2 Sen-
sor 2
OBD2 STAT OBD Status
OUT TEMP Ambient Air Temp
PM 11, PM 21 PM Sensor Mass Concentra-
tion Bank 1 Sensor 1, Bank 2
Sensor 1
PNTE_Stat PM NTE control area status
PTO STATUS PTO Status
PTO_STAT Power Take Off (PTO) Status
PTO_TIME Total Run Time With PTO
Active
REAG_DEMD Average Demanded Reagent
Consumption
REAG_LVL Reagent Tank Level
REAG_RATE Average Reagent Consumption
REL FRP Relative Fuel Rail Pressure
REL TPS Relative Throttle Position
RUN_TIME Total Engine Run Time
SCR REAG
DEV, DEV1,
DEV2, DEV3,
DEV4
SCR inducement system
actual state 10K history DEV1
(0 - 10000 km), 10K history
DEV2 (10000 - 20000 km),
10K history DEV3 (20000 -
30000 km), 10K history DEV4
(30000 - 40000 km): deviation
of reagent consumption
SCR REAG
LOW, LOW1,
LOW2, LOW3,
LOW4
SCR inducement system
actual state 10K history LOW1
(0 - 10000 km), 10K history
LOW2 (10000 - 20000 km),
10K history LOW3 (20000 -
30000 km), 10K history LOW4
(30000 - 40000 km): reagent
level too low
SCR RE-
AG WRONG,
WRONG1,
WRONG2,
WRONG3,
WRONG4
SCR inducement system
actual state 10K history
WRONG1 (0 - 10000 km), 10K
history WRONG2 (10000 -
20000 km), 10K history
WRONG3 (20000 - 30000 km),
10K history WRONG4 (30000 -
40000 km): incorrect reagent
SCR SYS AC-
TIVE
SCR inducement system
actual state: inducement sys-
tem active
PID PID description
SCR_DIST_1D Distance travelled in current
10K block (0 - 10000 km)
SCR_DIST_1N,
2N, 3N, 4N
Distance travelled while
inducement system active
in current 10K block 1N
(0 - 10000 km), 20K block 2N
(10 - 20000 km), 30K block 3N
(20 - 30000 km), 40K block 4N
(30 - 40000 km)
SECOND AIR Secondary Air Status
ST FTRM Fuel Trim Bank / Sensor
ST FTRM1, 3 Short Term Fuel Trim1 or 3
ST FTRM2, 4 Short Term Fuel Trim2 or 4
ST SEC
FT1, 2, 3, 4 Short Term Secondary O2
Sensor Fuel Trim 1, 2, 3, 4
TAC_A_CMD,
B_CMD Commanded Throttle Actuator
A Control, B Control
TAC_A_REL,
B_REL Relative Throttle A Position,
B Position
TCA_CINP,
TCB_CINP
Turbocharger Compressor
Inlet Pressure Sensor A, Pres-
sure Sensor B
TCA_CINT,
TCB_CINT
Turbocharger A Compres-
sor Inlet Temperature, Turbo-
charger B
TCA_COUT,
TCB_COUT
Turbocharger A Compressor
Outlet Temperature, Turbo-
charger B
TCA_RPM,
TCB_RPM Turbocharger A RPM, B RPM
TCA_TCOUT,
TCB_TCOUT Turbocharger A Turbine Outlet
Temperature, Turbocharger B
TCA_TINT,
TCB_TINT Turbocharger A Turbine Inlet
Temperature, Turbocharger B
THROT CMD Commanded Throttle Actua-
tor Control
TP G Absolute Throttle Position G
TQ_ACT Actual Engine - Percent Torque
TQ_DD Driver's Demand Engine - Per-
cent Torque
TQ_MAX1, 2,
3, 4, 5 Engine Percent Torque At
Point 1 (Idle), Point 2, 3, 4, 5
TQ_REF Engine Reference Torque
TROUB CODE Code causing the Freeze
Frame
14 | Operating instructions | OBD 1100 |en
574114 REV B | 08.2018 Bosch Automotive Service Solutions
PID PID description
VEH SPEED Vehicle Speed
VGT_A_ACT,
B_ACT Variable Geometry Turbo A
Position, Turbo B
VGT_A_CMD,
B_CMD Commanded Variable Geome-
try Turbo A Position, Turbo B
VGT_A_STAT,
B_STAT Variable Geometry Turbo A
Control Status, Turbo B
VPWR Control Module Voltage
WG_A_ACT, B_
ACT Wastegate A Position, B
Position
WG_A_CMD,
B_CMD Commanded Wastegate A
Control, B Control
TQ_DD Driver's demand engine per-
cent torque
TQ_ACT Actual engine percent torque
TQ_MAX1,
MAX2, MAX3,
MAX4, MAX5
Engine percent torque at
idle point 1, 2, 3, 4, 5
TQ_REF Engine reference torque
VGT_A_ACT Variable geometry turbo A
position
VGT_A_CMD Commanded variable geome-
try turbo A position
VGT_A_STAT Variable geometry turbo A con-
trol status
VGT_B_ACT Variable geometry turbo B
position
VGT_B_CMD Commanded variable geome-
try turbo B position
VGT_B_STAT Variable geometry turbo B con-
trol status
VPWR Control module voltage
WG_A_ACT Wastegate A position
WG_A_CMD Commanded wastegate A
control
WG_B_ACT Wastegate B position
WG_B_CMD Commanded wastegate B
control
| OBD 1100 | Operating instructions | 15en
574114 REV B | 08.2018Bosch Automotive Service Solutions
Limited Warranty
This warranty is expressly lim-
ited to original retail buyers
of Bosch electronic diagnostic
tools (“Units”).
Bosch Units are warranted against
defects in materials and work-
manship for one year (12 months)
from date of delivery. This war-
ranty does not cover any Unit that
has been abused, altered, used
for a purpose other than that for
which it was intended, or used
in a manner inconsistent with
instructions regarding use. The
sole and exclusive remedy for
any Unit found to be defective is
repair or replacement, the option
of Bosch. In no event shall Bosch
be liable for any direct, indirect,
special, incidental or consequen-
tial damages (including lost prot)
whether based on warranty,
contract, tort or any other legal
theory. The existence of a defect
shall be determined by Bosch
in accordance with procedures
established by Bosch. No one is
authorized to make any statement
or representation altering the
terms of this warranty.
Disclaimer
The above warranty is in lieu of
any other warranty, express or
implied, including any warranty
of merchantability or tness for a
particular purpose.
Software
Unit software is proprietary,
condential information protected
under copyright law. Users have
no right in or title to Unit software
other than a limited right of use
revocable by Bosch. Unit soft-
ware may not be transferred or
disclosed without written consent
of Bosch. Unit software may not
be copied except in ordinary
backup procedures.
Technical Support /
Repair Service
If you have any questions on the
operation of the product, please
call 800-228-7667 or email tech@
boschdiagnostics.com.
Please contact Technical Support
for troubleshooting and service
options prior to sending any unit
for repair.
To send a unit in for repair, go to
www.repairtrack.bosch-automo-
tive.com and follow the online
instructions. This website will also
have the latest service policies
and service center locations.
If you do not have internet access,
please call 1-800-344-4013.
16 | Mode d’emploi | OTC 1100 |fr
574114 RÉV B | 08.2018 Bosch Automotive Service Solutions
Table des matières
Mesures de sécurité . . . . . . . . . . . 17
Mots indicateurs et symboles 17
Messages de sécurité importants .17
À propos de l’outil . . . . . . . . . . . . .18
Pièces de l’outil . . . . . . . . . . . . . . . 18
Icônes . . . . . . . . . . . . . . . . . . . . . . .19
Connexion de l’outil . . . . . . . . . . .19
Interface de l’utilisateur Menu
diagnostic . . . . . . . . . . . . . . . . . . . .20
Lire codes . . . . . . . . . . . . . . . . . . . .20
Sélection du véhicule . . . . . . . . . .21
Supprimer codes . . . . . . . . . . . . . .21
État MIL . . . . . . . . . . . . . . . . . . . . .22
Détecteurs I / M (émissions) . . . . . 22
Afcher données gées . . . . . . . .24
Numéro d’identication du
véhicule . . . . . . . . . . . . . . . . . . . . .24
Conguration du système . . . . . .24
Afcher données . . . . . . . . . . . . . .24
Dépannage . . . . . . . . . . . . . . . . . . .25
Dénitions des PID . . . . . . . . . . . .25
Garantie limitée . . . . . . . . . . . . . . .31
Avis de non-responsabilité . . . 31
Logiciel . . . . . . . . . . . . . . . . . . 31
Soutien technique ou service de
réparation . . . . . . . . . . . . . . . 31
English .................. 2
Español ................. 32
| OBD 1100 | Mode d’emploi | 17fr
574114 RÉV B | 08.2018Bosch Automotive Service Solutions
Mesures de sécurité
Ce manuel de l’utilisateur décrit les
fonctions de l’analyseur-contrôleur et
présente des instructions détaillées
concernant son utilisation. Consultez
et respectez toujours les messages
de sécurité et les procédures de test
fournies par le fabricant du véhicule
et de l’outil.
Lisez et comprenez
toutes les directives de
sécurité avant d’uti-
liser l’outil.
Une défaillance non détectée ou non
corrigée du véhicule peut causer
un accident grave, voire mortel.
Les renseignements importants
sur la sécurité contenus dans le
mode d’emploi ont pour objectif de
protéger l’utilisateur, les personnes
se trouvant à proximité et le véhicule.
Mots indicateurs et symboles
AVERTISSEMENT!
Indique une situation
potentiellement dange-
reuse susceptible, si
elle n’est pas évitée, de
causer des blessures
graves ou mortelles
à l’opérateur ou aux
personnes se trouvant
à proximité.
NOTIFICATION
Indique une condition
risquant de causer des
pertes de données.
BIndique une procédure à une
seule étape.
Messages de sécurité
importants
AVERTISSEMENT!
Cet outil ne détecte pas
forcément toutes les
défaillances. Ne prenez
pas de risques avec
les freins, la direction
ou les autres fonctions
vitales du véhicule.
Vous pourriez avoir un
grave accident.
Portez toujours des
lunettes étanches certi-
ées ANSI pour protéger
vos yeux.
• Avant de tester un véhicule,
placez le levier de vitesse en
POSITION DE STATIONNEMENT
(transmission automatique) ou
au POINT MORT (transmission
manuelle) et actionnez le frein
à main.
• Ne déposez jamais d’outils sur la
batterie du véhicule.
• L’acide de la batterie peut brûler.
En cas de contact, rincez à l’eau
ou neutralisez avec une base
18 | Mode d’emploi | OTC 1100 |fr
574114 RÉV B | 08.2018 Bosch Automotive Service Solutions
douce comme du bicarbonate
de soude. En cas de contact
avec les yeux, rincez avec de
l’eau et appelez immédiatement
un médecin.
• Ne fumez jamais à proximité
d’un véhicule et n’approchez
pas de amme nue. Les vapeurs
d’essence et de batterie
sont explosives.
• N’utilisez pas l’outil lorsque les
circuits internes ont été exposés
à l’humidité. Un court-circuit
interne peut causer un incendie
et endommager le véhicule
ou l’outil.
• Sauf indication contraire,
assurez-vous de toujours éteindre
le moteur avant de brancher
ou débrancher des compo-
sants électriques.
• La plupart des véhicules sont
munis de coussins gonables.
Respectez les mesures de
sécurité contenues dans le
manuel d’entretien du véhicule.
Vous risquez des blessures
graves voire mortelles en cas de
déploiement involontaire.
AVERTISSEMENT!
Un coussin gonable
peut se déployer
plusieurs minutes après
l’arrêt du véhicule.
• Respectez toutes les mises en
garde, tous les avertissements et
toutes les procédures d’entretien
du constructeur.
À propos de l’outil
L’analyseur-contrôleur permet
d’extraire et d’effacer / réinitialiser
les données de diagnostic du module
de contrôle du véhicule. Les données
de diagnostic peuvent être utilisées
pour déterminer la cause d’un
dysfonctionnement du véhicule.
Utiliser l’outil pour exécuter les
fonctions suivantes :
Codes / Données Effacer /
Réinitialiser Extraire
Codes confirmés
(Confirmed codes) Effacer •
Codes en suspens
(Pending codes) Effacer •
Codes permanents
(Permanent codes) — •
Afficher données
(View data) — •
État MIL
(MIL status) — •
Détecteurs I / M
(I/M monitors) Réinitialiser •
Afficher données
figées
(View freeze data)
Effacer •
NIV (Numéro
d’identification du
véhicule)
(VIN)
— •
| OBD 1100 | Mode d’emploi | 19fr
574114 RÉV B | 08.2018Bosch Automotive Service Solutions
Pièces de l’outil
Pièce Description
Écran
ACL Écran ACL monochrome avec
8 lignes de 21 caractères
READ
Permet de lire les codes et de
revenir aux écrans précédents.
Appuyez sur cette touche
lorsqu’une flèche vers le
haut (#) apparaît à l’écran.
ERASE
Permet d’Effacer les codes
et fait défiler les écrans.
Appuyez sur cette touche
lorsqu’une flèche vers le
bas ($) apparaît à l’écran.
ENTER Sélectionne l’élément affiché.
BACK Revient à l’écran précédent.
Connecteur
OBD II Relie l’outil au connecteur
du véhicule.
Icônes
Icône Description
$
Indique que des
renseignements
supplémentaires sont
disponibles sur l’écran
suivant en appuyant sur
la toucheERASE.
#
Indique que des
renseignements
supplémentaires sont
disponibles sur l’écran
précédent en appuyant
sur la touche READ.
CONFIRMED
Les codes confirmés sont
signalés lorsqu’un composant
indique la présence d’un
dysfonctionnement.
PENDING
Les codes en suspens sont
signalés si un problème survient
au cours du cycle de conduite
en cours ou pendant le dernier
cycle de conduite effectué.
PERMANENT
Les codes permanents
sont un type spécial de
codes confirmés que seul
le véhicule peut effacer.
x / y
Apparaît uniquement lorsque
vous consultez les codes.
Indique la séquence et la
quantité de codes (code x
sur y). Par exemple, « 2 / 9 »
indique que le 2e code sur les
9 codes signalés par le module
informatique, est affiché.
ABS $##
Mod $##
Apparaît uniquement lorsque
vous consultez les codes.
Indique le module informatique
qui a signalé le code.
ABS apparaîtra si le code est un
code ABS. Mod $nºnº apparaît
quand le code est un code
relatif au motopropulseur. Le
Mod $nºnº est le nom donné
au module de contrôle du
véhicule qui signale le code.
Indique que les touches
directes fléchées READ
et ERASE sont actives
Connexion de l’outil
Pour connecter l’outil au véhicule :
1. Placez le connecteur OBD II sous
la colonne de direction. S’il n’y a
pas de connecteur, une étiquette
devrait indiquer l’emplacement
du connecteur. Pour plus de
renseignements sur les connec-
teurs OBD II, accédez à
http://www.obdclearinghouse.
com/oemdb.
2. Si nécessaire, retirez le couvercle
du connecteur du véhicule.
3. Mettez l’interrupteur d’allumage
en position ON (marche). Ne
démarrez pas le moteur.
4. Raccordez le connecteur OBD II
de l’outil au connecteur du
véhicule. L’outil lit automati-
quement les codes et afche
20 | Mode d’emploi | OTC 1100 |fr
574114 RÉV B | 08.2018 Bosch Automotive Service Solutions
les données. Lorsque vous avez
consulté les données, appuyez
sur la touche
ENTER pour
retourner au Menu diagnostic.
NOTIFICATION
Si le véhicule émet
un code fabricant
spécique, l’outil vous
demandera si vous
désirez sélectionner le
véhicule et ensuite lire
les codes ABS.
Si le véhicule n’émet
pas un code fabricant
spécique, l’outil vous
demandera si vous
désirez sélectionner un
véhicule pour lire les
codes ABS. La fonction
ABS n’est pas prise
en charge par tous
les véhicules.
Interface de l’utilisateur
Menu diagnostic
Pour sélectionner les fonctions :
1. Dans le Menu diagnostic,
appuyez sur les touches de
direction
READ ou ERASE
jusqu’à ce que la fonction désirée
soit surlignée, puis appuyez
sur
ENTER pour extraire et
afcher les résultats.
DIAGNOSTIC MENU
====================
Read Codes
Erase Codes
MIL Status
View Data
View Freeze Data
^^
VIN
2. Lorsque la tâche est effectuée,
appuyer sur BACK pour
retourner à l’écran de sélection
du Menu diagnostic.
Lire codes
Pour lire les codes :
BAppuyez sur et maintenez
enfoncée la touche READ
pendant 2 secondes puis
relâchez-la, ou sélectionnez Lire
codes dans le Menu diagnostic.
Si l’ABS est pris en charge par votre
véhicule, un menu apparaît et vous
donne le choix de sélectionner
OBDII/EOBD
ou ABS. Sélectionnez
ABS pour lire les codes ABS, et
OBDII/EOBD
pour lire les codes du
motopropulseur liés aux émissions.
Pour tous les codes différents
des codes ABS, l’outil afche les
codes conrmés, en suspens, et
permanents. Les codes d’anomalie
conrmés sont signalés lorsqu’un
composant, un capteur ou une
autre pièce du véhicule indique la
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
dans d''autres langues
- English: Bosch OBD1100 Owner's manual
- español: Bosch OBD1100 El manual del propietario
Documents connexes
Autres documents
-
OTC 3208 Manuel utilisateur
-
Topdon ArtiDiag600 S Manuel utilisateur
-
Topdon ArtiDiag500 S Manuel utilisateur
-
Coway AP-3522F Airmega ProX Air Purifier Manuel utilisateur
-
Princess auto 8964330 Manuel utilisateur
-
Actron CP9575 Mode d'emploi
-
Wacker Neuson HIF690 Manuel utilisateur
-
-
Actron CP9690 Mode d'emploi
-
