Johnson Controls M9203-AGx-2(Z) Series On/Off and Floating Point Electric Spring Return Actuators Manuel utilisateur

Marque: Johnson Controls

Modèle: M9203-AGx-2(Z) Series On/Off and Floating Point Electric Spring Return Actuators

Taper: Manuel utilisateur

M9203-AGx-2(Z) Series On/Off and Floating Point Electric Spring Return Actuators

Installation Instructions

Applications

The M9203-AGx-2(Z) Series On/Off and Floating Point

Electric Spring Return Actuators are direct-mount

actuators that operate on AC/DC 24 V power. These

bidirectional actuators do not require a damper linkage,

and are easily installed on round shafts from

1/4to1/2in.(6to12mm) or square shafts from

1/4 to 5/16 in. (6 to 8 mm) using the standard shaft

clamp included with the actuator.

A single M9203-AGx-2(Z) Series On/Off and Floating

Point Electric Spring Return Actuator provides

27 lb·in. (3 N·m) running and spring return torque. An

integral line voltage auxiliary switch, available only on

the M9203-xxB-2(Z) models, indicates end-stop

position, or performs switching functions within the

selected rotation range.

M9203-AGA-2(Z) actuators include plenum-rated

cables and are specially configured for installation in

spaces used for environmental air-handling purposes

other than ducts and plenums as specified in National

Fire Protection Association (NFPA) 70: National

Electrical Code section 300.22(C), Other Space Used

for Environmental Air. The space over a hung ceiling

used for environmental air handling purposes is an

example of the type of space for which these actuators

are configured.

Installation

The M9203-AGx-2(Z) Series On/Off and Floating Point

Electric Spring Return Actuators mount directly to the

surface in any convenient orientation using two

No. M3.5 x 9.5 mm self-drilling sheet metal screws and

the anti-rotation bracket (parts included with the

actuator). No additional linkages or couplers are

required. Electrical connections are color-coded and

identified with numbers permanently marked on the

actuator cable. A tag on the actuator cable identifies

the electrical connections and wiring details are

included on the actuator housing.

IMPORTANT: Use this M9203-AGx-2(Z) Series

On/Off and Floating Point Electric Spring Return

Actuator only to control equipment under normal

operating conditions. Where failure or malfunction of

the actuator could lead to personal injury or property

damage to the controlled equipment or other

property, additional precautions must be designed

into the control system. Incorporate and maintain

other devices, such as supervisory or alarm systems

or safety or limit controls, intended to warn of or

protect against failure or malfunction of the actuator.

IMPORTANT : Utiliser ce M9203-AGx-2(Z) Series

On/Off and Floating Point Electric Spring Return

Actuator uniquement pour commander des

équipements dans des conditions normales de

fonctionnement. Lorsqu'une défaillance ou un

dysfonctionnement du actuator risque de provoquer

des blessures ou d'endommager l'équipement

contrôlé ou un autre équipement, la conception du

système de contrôle doit intégrer des dispositifs de

protection supplémentaires. Veiller dans ce cas à

intégrer de façon permanente d'autres dispositifs,

tels que des systèmes de supervision ou d'alarme,

ou des dispositifs de sécurité ou de limitation, ayant

une fonction d'avertissement ou de protection en

cas de défaillance ou de dysfonctionnement du

actuator.

M9203-AGx-2(Z) Series On/Off and Floating Point Electric

Spring Return Actuators

Installation Instructions

M9203-AGA-2, M9203-AGB-2,

M9203-AGA-2Z, M9203-AGB-2Z Part No. 34-1791-8, Rev. G

Issued May 2021

*3417918G*

M9203-AGx-2(Z) Series On/Off and Floating Point Electric Spring Return Actuators Installation Instructions2

Parts Included

• M9203-AGx-2(Z) actuator

• M9203-603 adjustable stop kit

• M9000-604 anti-rotation bracket with two

No. M3.5 x 9.5 mm, pan-head, cross-recessed

(Phillips), self-drilling and self-tapping screws

Special Tools Needed

• 10 mm wrench/socket

• drill with Phillips bit, driver size 1

Dimensions

IMPORTANT: Do not install or use this

M9203-AGx-2(Z) Series On/Off and Floating Point

Electric Spring Return Actuator in or near

environments where corrosive substances or vapors

could be present. Exposure of the electric actuator

to corrosive environments may damage the internal

components of the device, and will void the

warranty.

Figure 1: M9203-AGx-2 Series On/Off and Floating Point Electric Spring Return Actuator

Dimensions, in. (mm)

10 30

1/4 (6.5) Slot Width

5/16 (8) Slot Length

4-15/64

(107.5)

25/32

(20)

3-15/16

(82)

15/64

(6)

2-1/4

(57.5)

45/64

(18)

1-1/8

(28.7)

1-35/64

(39.2)

47/64

(18.7)

FIG:M9203_AGx_dim

DA RA

6-3/8

(162)

4-55/64

(123.6)

M9203-AGx-2(Z) Series On/Off and Floating Point Electric Spring Return Actuators Installation Instructions 3

Accessories

Mounting

The M9203-AGx-2(Z) Series On/Off and Floating Point

Electric Spring Return Actuators can be easily installed

on dampers with round shafts from 1/4 to 1/2 in.

(6 to 12 mm) or square shafts from 1/4 to 5/16 in.

(6 to 8 mm) using the standard shaft coupler included

with the actuator. If the damper shaft extends less than

3.31 in. (84 mm), see the Removable Coupler section

for further instructions. If the damper shaft extends less

than 0.79 in. (20 mm), install a shaft extension

recommended by the damper manufacturer.

Table 1: Accessories and Replacement Parts (Order Separately)

Code Number Description

DMPR-KC003 7 in. (178 mm) Blade Pin Extension (without bracket) for Johnson Controls® Direct-Mount Damper

Applications (quantity 1)

Note: Available with damper and may be ordered separately

M9000-322 Weathershield Kit for Damper Application of VA9104, VA9203, VA9208, and VA9308/9310 Series Electric

Actuators (quantity 1)

M9000-400 Jackshaft Linkage Adapter Kit (quantity 1)

M9000-560 Ball Valve Linkage Kit for applying M9104, M9203, and M9208 Series Electric Actuators to VG1000 Series

Valves (quantity 1)

M9000-561 Thermal Barrier Kit for M9000-560 Ball Valve Linkage. Extends M(VA)9104, M(VA)9203, M(VA)9208, and

M(VA)9308/9310 Series Electric Actuators applications to include low pressure steam (quantity 1)

M9000-604 Replacement Anti-Rotation Bracket Kit for M9203, M9208, M9220, and M9300 Series Electric Actuators

(quantity 1)

M9000-606 Position Indicator for Damper Applications (quantity 5)

M9000-607 Position Indicator for VG1000 Series Ball Valve Applications (quantity 5)

M9203-100 Remote Mounting Kit with Crankarm Kit (quantity 1)

M9203-110 Universal Mounting Kit without Crankarm Kit (quantity 1)

M9203-115 Universal Mounting Kit with Crankarm Kit (quantity 1)

M9203-150 Crankarm Kit (quantity 1)

M9203-250 Remote Mounting Kit with Crankarm Kit and Damper Linkage for D1300 Dampers (quantity 1)

M9203-601 Replacement Standard Coupler Kit (with Retainer) for Mounting M9203 Series Electric Spring Return

Actuators (quantity 1)

M9203-602 Replacement Retainer for M9203 Series Electric Spring Return Actuators (quantity 5)

M9203-603 Adjustable Stop Kit for M9203 Series Electric Spring Return Actuators (quantity 1)

M9000-700 Universal Ball Valve Linkage Kit (Quantity 1)

M9203-AGx-2(Z) Series On/Off and Floating Point Electric Spring Return Actuators Installation Instructions4

Counterclockwise (CCW) Spring Return

Direction – Clockwise (CW) Powered

Operation

For CCW spring return direction, mount the actuator to

the damper shaft so that Side A of the actuator is away

from the damper as illustrated in Figure 2. With power

applied, the actuator drives CW from the 0° position

and spring returns CCW.

Clockwise (CW) Spring Return Direction –

Counterclockwise (CCW) Powered Operation

For CW spring return direction, mount the actuator to

the damper shaft so that Side B of the actuator is away

from the damper as illustrated in Figure 3. With power

applied, the actuator drives CCW from the 0° position

and spring returns CW.

Removable Coupler

If the damper shaft extends less than 3.31 in. (84 mm),

mount the coupler on the face of the actuator closest to

the damper.

If the damper shaft extends less than 0.79 in. (20 mm),

a shaft extension is required to mount the actuator.

To change the coupler’s position, see Figure 4 and

proceed as follows:

1. Mount the coupler on either Side A or Side B of the

actuator as determined by the shaft length.

2. Snap the locking clip securely into the coupler

retention groove to retain the coupler.

Mounting the Actuator

To mount the actuator, proceed as follows:

1. See the dimensions in Figure 5 and Table 2 to

ensure the correct positioning of the anti-rotation

bracket.

Figure 2: Actuator Side A

DA RA

FIG:M9203_AGx_A

Figure 3: Actuator Side B

RA DA

50 30

FIG:M9203_AGx_B

Table 2: Dimensions from Anti-Rotation Bracket

to Shaft Center

Shaft Diameter,

in. (mm)

Dimension A,

in. (mm)

Dimension B,

in. (mm)

1/4 to 1/2 (6 to 12) 4-27/32 (123) 3-5/8 (92)

Figure 4: Changing the Coupler Position

FIG:ex p_cplr

Figure 5: Positioning the Anti-Rotation Bracket

DA RA

10 10

FIG:M9203_AGx_brkt

DIM. A

DIM. B

M9203-AGx-2(Z) Series On/Off and Floating Point Electric Spring Return Actuators Installation Instructions 5

2. Bend or cut the anti-rotation bracket to fit the

damper frame or duct as illustrated in Figure 6.

Note: The anti-rotation bracket can be bent to fit a

round damper.

3. Mark or drill mounting holes in the damper frame or

duct using the anti-rotation bracket as a guide

(based on the measurements obtained in Table 2

and Figure 5).

4. Secure the anti-rotation bracket to the damper

frame or duct using the two No. M3.5 x 9.5 mm

self-drilling sheet metal screws provided.

5. Slide the actuator onto the damper shaft, and

position the anti-rotation bracket tab into the slot at

the bottom of the actuator as illustrated in Figure 6.

6. Rotate the damper blade(s) to the desired position

if the power is lost.

7. Hold the actuator perpendicular to the damper

shaft. Evenly hand-tighten each nut on the coupler

U-bolt, then torque the coupler U-bolt nuts to

100 to 125 lb·in. (11 to 14 N·m).

8. Apply power long enough for the actuator to travel

a full stroke. Verify that the actuator rotates freely

throughout the range.

Limiting Rotation Range Using M9203-603

Adjustable Stop Kit

The actuator is factory set for 95° rotation, and its

range is limited in 5° increments to a minimum of 35°. A

stroke-limiting stop can be attached in the field to the

shaft coupler side of the actuator to reduce the rotation

range. Attaching the stroke-limiting stop in the furthest

mounting position reduces the rotation range of the

actuator by 5°. Each progressive mounting position

reduces the rotation range an additional 5°.

1. Check that the damper blade is visible or its

position is permanently marked on the end of the

damper shaft, as illustrated in Figure 7.

2. Position the stroke-limiting stop in the serrated slot

with its leading edge at the scale position matching

the desired stroke.

3. The product label marks hole positions for the

M3-0.5 x 8 mm self-tapping screw provided with

the adjustable stop kit. Drive the screw through the

slot in the adjustable stop and into the actuator

face over a marked hole position. (See Figure 8.)

Note: The minimum rotation range is 35°.

IMPORTANT: The tab on the anti-rotation bracket

must fit midpoint in the actuator slot. Positioning the

tab midpoint in the slot prevents actuator binding

and premature wear, and makes actuator removal

easier.

IMPORTANT: Do not overtighten the mounting

screws to avoid stripping the threads. Be certain that

the tab on the anti-rotation bracket remains properly

positioned in the slot on the actuator, and that the

actuator remains parallel to the mounting surface.

Figure 6:

Anti-Rotation Mounting Bracket

FIG:M9203_ Anti-Rotn_Mntg_Brkt_Posn

2-1/4

(57.5)

3-1/4

(82.5)

Anti-Rotation Bracket

Damper Frame

Self-Drilling Sheet Metal Screws (2)

Figure 7: Damper Position

FIG:dampers

FIG

:dampos

Figure 8: Limiting Rotation Range

FIG:strk_limit

M9203-AGx-2(Z) Series On/Off and Floating Point Electric Spring Return Actuators Installation Instructions6

Wiring

See Figure 9 and Figure 10 to wire the applicable

M9203-AGx-2(Z) Series model.

Figure 9: Control Wiring

24 VAC

24 VDC

DADA

BLK

RED GRY ORN

123

Floating Control, Four Wire

24 VAC

24 VDC

DADA

BLK

RED GRY ORN

123

On/Off Control, Two Wire

24 VAC

24 VDC

DADA

BLK

RED GRY ORN

123

Open/Close, Single Wire Control

FIG:M92xx-AGx_cntrlwir

24 VAC

24 VDC

DADA

BLK RED GRY ORN

123

DADA

BLK RED GRY ORN

123

Floating Control, Multiple Actuators with One Transformer

WARNING: Risk of Electric Shock.

Disconnect or isolate all power supplies

before making electrical connections.

More than one disconnection or isolation

may be required to completely

de-energize equipment. Contact with

components carrying hazardous voltage

can cause electric shock and may result

in severe personal injury or death.

AVERTISSEMENT : Risque de

décharge électrique.

Débrancher ou isoler toute alimentation

avant de réaliser un branchement

électrique. Plusieurs isolations et

débranchements sont peut-être

nécessaires pour -couper entièrement

l'alimentation de l'équipement. Tout

contact avec des composants

conducteurs de tensions dangereuses

risque d'entraîner une décharge

électrique et de provoquer des blessures

graves, voire mortelles.

CAUTION: Risk of Property Damage.

Do not apply power to the system before

checking all wiring connections. Short

circuited or improperly connected wires

may result in permanent damage to the

equipment.

MISE EN GARDE : Risque de dégâts

matériels.

Ne pas mettre le système sous tension

avant d'avoir vérifié tous les raccords de

câblage. Des fils formant un court-circuit

ou connectés de façon incorrecte

risquent d'endommager

irrémédiablement l'équipement.

Figure 10: Auxiliary Switch Wiring Diagram

COM NC NO

21 22 23

BLK/

RED

BLK/

BLU

BLK/

GRY

FIG:aux_wring

M9203-AGx-2(Z) Series On/Off and Floating Point Electric Spring Return Actuators Installation Instructions 7

Using Conduit

All M9203-xxx-2(Z) Series Actuators accept 1/2 in.

threaded electrician’s fittings.

1. Feed the actuator cables through the field supplied

electrician’s fitting and conduit.

2. Thread the electrician’s fitting into the actuator and

secure the conduit to the fitting in accordance with

local building code requirements.

Setup and Adjustments

Mode Selection Switch

Actuators have an external mode selection switch to

reverse control logic. The switch is accessible from

both A and B sides of the actuator as illustrated in

Figure 12. Actuators are delivered in Direct Acting (DA)

mode and can be switched by the user to Reverse

Acting (RA) mode.

CAUTION: Risk of Property Damage.

Insulate and secure each unused wire

lead before applying power to the

actuator. Failure to insulate and secure

each unused wire lead may result in

property damage.

MISE EN GARDE : Risque de dégâts

matériels.

Isoler et protéger chaque fil non utilisé

avant de mettre l'actuator sous tension.

Le non-respect de cette obligation

d'isolation et de protection de chaque fil

non utilisé risque d'entraîner des dégâts

matériels.

IMPORTANT: Make all wiring connections in

accordance with the National Electrical Code and

local regulations. Use proper Electrostatic Discharge

(ESD) precautions during installation and servicing

to avoid damaging the actuator’s electronic circuits.

Figure 11: Adding Flexible Metal Conduit

FIG:add_cndt

Figure 12: Mode Selection

FIG:AGx

_modsel

Side A of Actuator Side B of Actuator

DA RA DARA

M9203-AGx-2(Z) Series On/Off and Floating Point Electric Spring Return Actuators Installation Instructions8

Control Response

The installation side of the actuator and the position of

the mode selection switch combine to determine

control response from the actuator. See Figure 13.

Auxiliary Switch (M9203-xxB-2(Z) Models)

The M9203-xxB-2(Z) models include one integral

auxiliary switch with a switch adjuster accessible on

either face of the actuator (see Figure 2 and Figure 3).

The factory setting for the Auxiliary Switch is

11° closing (relative to the 0 to 90° rotation range as

printed on the product label). See the Technical

Specifications table for the auxiliary switch ratings.

The switch point is continuously adjustable throughout

the actuator’s rotation range. For the most accurate

switch positioning, see Figure 14 and use the method

in the following example.

To change the switch point, proceed as follows:

1. Position the actuator in the full spring return

position.

Note: The switch is factory set to trip when the

actuator reaches the 11° position.

2. Rotate the switch adjuster until it points to the

desired switch point.

3. Connect the Auxiliary Switch to a power source or

an ohmmeter and apply power to the actuator. The

actuator moves to the fully open position and holds

while power is applied.

4. Observe the switch point. If required, repeat Step 1

through Step 3.

Repair Information

A number of replacement parts are available; see

Table 1 for more details. If an M9203-AGx-2(Z) Series

On/Off and Floating Point Control Electric Spring

Return Actuator fails to operate within its specifications,

replace the unit. For a replacement electric actuator,

contact the nearest Johnson Controls representative.

WARNING: Risk of Electric Shock and

Property Damage.

Insulate and secure each unused wire

lead before applying power to the

actuator. Failure to insulate and secure

each unused wire lead may result in

property damage, electric shock, and

severe personal injury or death.

AVERTISSEMENT : Risque de

décharge électrique et dégâts

matériels.

Isoler et protéger chaque fil non utilisé

avant de mettre l'actuator sous tension.

Le non-respect de cette obligation

d'isolation et de protection de chaque fil

non utilisé risque d'entraîner des dégâts

matériels, des décharges électriques et

des blessures graves, voire mortelles.

Figure 13: Control Response

FIG:M92xxAGx_CtrlRs pns

Control Inputs

GRY ORN

Mode Selection Switch

Installation Side

50 30

Figure 14: Switch Trip Point Settings

Switch Adjuster

FIG:swtch_sttng

M9203-AGx-2(Z) Series On/Off and Floating Point Electric Spring Return Actuators Installation Instructions 9

Technical Specifications

M9203-AGx-2(Z) Series On/Off and Floating Point Control Electric Spring Return Actuator

(Part 1 of 2 )

Power

Requirements

-AGx-2 Models AC 24 V (AC 19.2 V to 28.8 V) at 50/60 Hz: Class 2 (North America) or Safety

Extra-Low Voltage (SELV) (Europe), 4.7 VA Running, 2.7 VA Holding Position

DC 24 V (DC 21.6 V to 28.8 V): Class 2 (North America) or SELV (Europe), 1.8 W

Running, 1 W Holding Position

Minimum Transformer Size: 6 VA per Actuator

-AGx-2Z Models AC 24 V (AC 19.2 V to 28.8 V) at 50/60 Hz: Class 2 (North America) or Safety

Extra-Low Voltage (SELV) (Europe), 5.1 VA Running, 2.8 VA Holding Position DC

24 V (DC 19.2 V to 28.8 V): Class 2 (North America) or SELV (Europe), 1.9 W

Running, 1.1 W Holding Position

Minimum Transformer Size: 6 VA per Actuator

Input Signal -AGx-2(Z) Models AC 19.2 to 28.8 V at 50/60 Hz or DC 24 V +20%/-10%

Class 2 (North America) or SELV (Europe)

Minimum Pulse Width: 500 msec

Control Input

Impedance

-AGx-2(Z) Models 4,700 ohm

Auxiliary Switch

Rating

-xxB Models One Single-Pole, Double-Throw (SPDT), Double-Insulated Switch with Silver

Contacts:

AC 24 V, 50 VA Pilot Duty

AC 120 V, 5.8 A Resistive, 1/4 hp, 275 VA Pilot Duty

AC 240 V, 5.0 A Resistive, 1/4 hp, 275 VA Pilot Duty

Spring Return Direction Is Selectable with Mounting Position of Actuator:

Actuator Face Labeled A Is Away from Damper or Valve: CCW Spring Return

Actuator Face Labeled B Is Away from Damper or Valve: CW Spring Return

Rated Torque Power On

(Running)

27 lb·in. (3 N·m) All Operating Temperatures

Power Off

(Spring

Returning)

27 lb·in. (3 N·m) All Operating Temperatures

Rotation Range Maximum Full Stroke: 95°

Adjustable Stop: 35 to 95° Maximum Position

Rotation Time

for 90 Degrees of

Travel

Power On

(Running)

-AGx-2 Models

150 Seconds Constant for 0 to 27 lb·in. (3 N·m) Load, at All Operating Conditions

Power On

(Running)

-AGx-2Z Models

90 Seconds Constant for 0 to 27 lb·in. (3 N·m) Load, at All Operating Conditions

Power Off

(Spring

Returning)

12 to 17 Seconds for 0 to 27 lb·in. (3 N·m) Load, at Room Temperature

16 Seconds Nominal at Full Rated Load

22 Seconds Maximum with 27 lb·in. (3 N·m) Load at -22°F (-30°C)

Life Cycles 60,000 Full Stroke Cycles with 27 lb·in. (3 N·m) Load

1,500,000 Repositions with 27 lb·in. (3 N·m) Load

Published in U.S.A. www.johnsoncontrols.com

M9203-AGx-2(Z) Series On/Off and Floating Point Electric Spring Return Actuators Installation Instructions10

Metasys® and Johnson Controls® are registered trademarks of Johnson Controls.

Audible Noise

Rating

Power On

(Running)

-AGx-2 Models

<28 dBA at 27 lb·in. (3 N·m) Load, at a Distance of 39-13/32 in. (1 m)

Power On

(Running)

-AGx-2Z Models

<37 dBA at 27 lb·in. (3 N·m) Load, at a Distance of 39-13/32 in. (1 m)

Power On

(Holding)

<20 dBA at a Distance of 39-13/32 in. (1 m)

Power Off

(Spring

Returning)

<56 dBA at 27 lb·in. (3 N·m) Load, at a Distance of 39-13/32 in. (1 m)

Electrical

Connections

-AGA-2(Z) Models 120 in. (3.05 m) UL 444 Type CMP Plenum Rated Cable with 19 AWG (0.75 mm²)

Conductors and 0.25 in. (6 mm) Ferrule Ends

Auxiliary Switch

(-xxB Models)

48 in. (1.2 m) UL 758 Type AWM Halogen Free Cable with 18 AWG (0.85 mm²)

Conductors and 0.25 in. (6 mm) Ferrule Ends

Conduit Connections Integral 1/2 in. (13 mm) Threaded Conduit Connector(s)

Mechanical

Connections

Round Shafts Range of Sizes: 1/4 to 1/2 in. (6 to 12 mm)

Square Shafts Range of Sizes: 1/4 to 5/16 in. (6 to 8 mm)

Enclosure Rating NEMA 2 (IP54) for all Mounting Orientations

Ambient

Conditions

Standard

Operating

-22 to 140°F (-30 to 60°C); 90% RH Maximum, Noncondensing

Storage -40 to 185°F (-40 to 85°C); 95% RH Maximum, Noncondensing

Dimensions 6.38 x 3.23 x 2.26 in. (162 x 82 x 57.5 mm)

Compliance United States UL Listed, CCN XAPX, File E27734; to UL 60730-1A: 2003-08, Ed. 3.1, Automatic

Electrical Controls for Household and Similar Use;

and UL 60730-2-14: 2002-02, Ed. 1, Part 2, Particular Requirements for Electric

Actuators. (Models: All)

Plenum Rated (UL 2043). Suitable for use in other environmental air space

(plenums) in accordance with Section 300.22 (C) of the National Electric Code

Canada UL Listed, CCN XAPX7, File E27734; to UL 60730-1:02-CAN/CSA: July 2002, 3rd

Ed., Automatic Electrical Controls for Household and Similar Use;

and CSA C22.2 No. 24-93 Temperature Indicating and Regulating Equipment

(Models: All)

Europe CE Mark – Johnson Controls, Inc. declares that this product is in compliance with

the essential requirements and other relevant provisions of the EMC Directive and

Low Voltage Directive.

Australia and

New Zealand

RCM Mark, Australia/NZ Emissions Compliant (Models: All)

Shipping Weight -AGA Models: 2.0 lb (0.9 kg)

-AGB Models: 2.4 lb (1.1 kg)

European Single Point of Contact: NA/SA Single Point of Contact: APAC Single Point of Contact:

JOHNSON CONTROLS

WESTENDHOF 3

45143 ESSEN

GERMANY

JOHNSON CONTROLS

507 E MICHIGAN ST

MILWAUKEE WI 53202

USA

JOHNSON CONTROLS

C/O CONTROLS PRODUCT MANAGEMENT

NO. 22 BLOCK D NEW DISTRICT

WUXI JIANGSU PROVINCE 214142

CHINA

M9203-AGx-2(Z) Series On/Off and Floating Point Control Electric Spring Return Actuator

(Part 2 of 2 )

Product warranty

This product is covered by a limited warranty, details of which can be found at www.johnsoncontrols.com/buildingswarranty.

Patents

Patents: http://jcipat.com

Johnson Controls M9203-AGx-2(Z) Series On/Off and Floating Point Electric Spring Return Actuators Manuel utilisateur

Marque: Johnson Controls

Modèle: M9203-AGx-2(Z) Series On/Off and Floating Point Electric Spring Return Actuators

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Johnson Controls M9203-AGx-2(Z) Series On/Off and Floating Point Electric Spring Return Actuators User manual

Johnson Controls M9203-AGx-2(Z) Series On/Off and Floating Point Electric Spring Return Actuators Manuel utilisateur

Johnson Controls M9203-AGx-2(Z) Series On/Off and Floating Point Electric Spring Return Actuators Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents