luminii LETO 44 Mini P Guide d'installation

Taper
Guide d'installation
LETO 44 Mini P
1 Rev July 26, 2021 403-216-7043 | [email protected]
MADE IN
CANADA
PROUD MEMBER OF
Read and follow these
instructions before installing or
maintaining this product
Veuillez lire et suivre ces
instructions avant l’installation ou
l’entretien de ce produit
• This product is suitable for DRY INDOOR
LOCATIONS ONLY
• Make sure this product is NOT on the same
circuit as inductive loads, (e.g. fluorescent bulbs,
discharge bulbs, ventilation fans, etc...)
• Do not switch on line voltage until all wiring is
complete
• Incorrect wiring will result in irreparable damage
to LED and power supply
• This product should only be installed by a
licensed electrician
• Ce produit convient pour une installation DANS
UN ENDROIT SEC SEULEMENT
• Assurer vous que des charges inductives ne se
retrouvent pas sur le même circuit que ce produit,
(i.e. fluorescent, ampoules à décharge,
ventilateurs, etc...)
• Compléter les branchements avant de mettre
sous tension
• Un branchement incorrect créerait des
dommages irréparables à l’alimentation et au DEL
• Ce produit devrait être uniquement installé par un
électricien qualifié
Warranty
Garantie
• This product must be installed in accordance
with all applicable installation codes and
ordinance
• Limited five (5) years warranty
• Warranty is void in the eventuality of
unauthorized modifications and/or improper use
• Ce produit doit être installé conformément au
code d’installation et autres normes applicables
• Garantie limitée de cinq (5) ans
• La garantie est non valide advenant une
modification non autorisée ou un usage non
approprié
Powered Aircraft
AC P4 / DC P5
For powered aircraft height
adjustment, see P6
Feed Suspended
AC P2 / DC P3
954 SEMI-RECESSED CANOPY
Overview / Vue d’ensemble
LETO 44 Mini P
2 Rev July 26, 2021 403-216-7043 | [email protected]
MADE IN
CANADA
PROUD MEMBER OF
Turn screws until housing is secured in place
(arms will rotate and clamp down on ceiling)
9-25mm
Pendant: Single Feed Cable (AC Connection)
Finish ceiling installation. Make sure hole is cut to
appropriate size and location. 54mm (2.125”)
Disassemble driver housing to expose the driver.
2
Make electrical connections and use appropriate
strain relief.
3
Reassemble housing and insert into ceiling. Push
aside to leave room for canopy.
Unscrew gripper plate and separate from canopy.
7
Connect dimming controls to included cable
clamps. Insert wires and canopy into ceiling.
5
Loosen set screw and adjust cable to desired
height. Cut and reconnect wire if needed.
8
Re-attach gripper to canopy and slide trim plate
up until held in place by magnets.
9
1
4 6
LETO 44 Mini P
3 Rev July 26, 2021 403-216-7043 | [email protected]
MADE IN
CANADA
PROUD MEMBER OF
Pendant: Single Feed Cable (Remote DC Connection)
1
Finish ceiling installation. Make sure hole is cut to
appropriate size and location. 54mm (2.125”)
Disassemble driver housing to expose fixture
wiring. Cylinder housing is used as DC junction
box.
2
Make electrical connections and use appropriate
strain relief.
3
4
Reassemble housing and insert into ceiling. Push
aside to leave room for canopy.
Unscrew gripper plate and separate from canopy.
7
Insert canopy into ceiling.
5
Loosen set screw and adjust cable to desired
height. Cut and reconnect wire if needed.
8
Re-attach gripper to canopy and slide trim plate
up until held in place by magnets.
9
6
Turn screws until housing is secured in place
(arms will extend and clamp down on ceiling)
9-25mm
LETO 44 Mini P
4 Rev July 26, 2021 403-216-7043 | [email protected]
MADE IN
CANADA
PROUD MEMBER OF
6
Turn screws until housing is secured in place
(arms will extend and clamp down on ceiling)
9-25mm
Pendant: Powered Aircraft Cable (AC Connection)
1
Finish ceiling installation. Make sure hole is cut to
appropriate size and location. 54mm (2.125”)
Disassemble driver housing to expose the driver.
2
Make electrical connections and use appropriate
strain relief.
3
4
Reassemble housing and insert into ceiling. Push
aside to leave room for canopy.
Connect dimming controls to included cable
clamps. Insert wires and canopy into ceiling.
5
Slide trim plate up until held in place by magnets.
7
LETO 44 Mini P
5 Rev July 26, 2021 403-216-7043 | [email protected]
MADE IN
CANADA
PROUD MEMBER OF
Pendant: Powered Aircraft Cable (Remote DC Connection)
1
Finish ceiling installation. Make sure hole is cut to
appropriate size and location. 54mm (2.125”)
Disassemble driver housing to expose fixture
wiring. Cylinder housing is used as DC junction
box.
2
Make electrical connections and use appropriate
strain relief.
3
4
Reassemble housing and insert into ceiling. Push
aside to leave room for canopy.
Insert canopy into ceiling.
5
Slide trim plate up until held in place by magnets.
7
6
Turn screws until housing is secured in place
(arms will extend and clamp down on ceiling)
9-25mm
LETO 44 Mini P
6 Rev July 26, 2021 403-216-7043 | [email protected]
MADE IN
CANADA
PROUD MEMBER OF
Unscrew gripper plate separate from canopy.
2
Loosen set screw and adjust cable to desired
height.
3
If cables develop a twist, loosen set screw and
cycle cable through the gripper 4-5 times.
5
Cut excess cable leaving ~3” above gripper.
Make electrical connections using appropriate
hardware.
4
Tighten screws, re-attach gripper plate to canopy
and slide trim plate up until held in place by
magnets.
6
Remove trim plate from the canopy
1
Height Adjustment: Powered Aircraft Cable
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

luminii LETO 44 Mini P Guide d'installation

Taper
Guide d'installation

dans d''autres langues