Maytag MGR6775BDW - Gas Double Oven Range Mode d'emploi

Marque: Maytag

Modèle: MGR6775BDW - Gas Double Oven Range

Taper: Mode d'emploi

MA A(]

Nlaytag Gas

Double Oven Range

Precision Touch 750 Series

important Safety

Instructions ............................... 1=4

Surface Cooking ...................... 5=6

Controls

Sealed Gas Burners

Oven Cooking ......................... 7-14

Control Panel

Baking

Cook & Hold

Delay

Keep Warm

Broiling

Oven Racks

Care & Cleaning ................... 15=18

Self-Clean Oven

Cleaning Procedures

Maintenance ......................... 19=20

Oven Doors. Windows & Lights

Removal of Gas Appliance

Troubleshooting ................... 21 =22

Warranty & Service .................... 23

Guide d'utilisation et

d'entretien ................................... 24

Guia de uso y cuidado .............. 50

General instructions

To ensure proper and safe operation: Appliance must

be properly installed and grounded by a qualified

technician. Do not attempt to adjust, repair, service, or

replace any part of your appliance unless it is specifically

recommended in this guide. All other servicing should be

referred to a qualified servicer. Have the installer show

you the location of the gas shut off valve and how to

shut it off in an emergency.

Always disconnect power to appliance before servicing.

ImpomntSefety

Warning and Important Safety Instructions appearing in

this guide are not meant to cover all possible conditions

and situations that may occur. Common sense, caution,

and care must be exercised when installing, maintaining,

or operating the appliance.

Always contact your dealer, distributor, service agent or

manufacturer about problems or conditions you do not

understand.

Recognize Safety Symbols, Words, Labels

Read and follow all instructions before using this

appliance to prevent the potential risk of fire, electric

shock, personal injury or damage to the appliance as a

result of improper usage of the appliance. Use appliance

only for its intended purpose as described in this guide.

importantSurety

To check if device is properly installed, look underneath

range with a flashlight to make sure one of the rear

leveling legs is properly engaged in the bracket slot. The

anti-tip device secures the rear leveling leg to the floor

when properly engaged. You should check this anytime

the range has been moved.

Do not use water on grease fires. Use baking soda, a

dry chemical or foam-type extinguisher to smother fire

or flame.

Child Safety

To Prevent Fire or

Smoke Damage

Be sure all packing materials are removed from the

appliance before operating it.

Keep area around appliance clear and free from

combustible materials, gasoline, and other flammable

vapors and materials.

If appliance is installed near a window, proper

precautions should be taken to prevent curtains from

blowing over burners.

NEVER leave any items on the cooktop. The hot air from

the vent may ignite flammable items and may increase

pressure in closed containers which may cause them to

burst.

Many aerosol-type spray cans are EXPLOSIVE when

exposed to heat and may be highly flammable. Avoid

their use or storage near an appliance.

Many plastics are vulnerable to heat. Keep plastics away

from parts of the appliance that may become warm or

hot. Do not leave plastic items on the cooktop as they

may melt or soften if left too close to the vent or a lighted

surface burner.

To eliminate the hazard of reaching over hot surface

burners, cabinet storage should not be provided directly

above a unit. If storage is provided, it should be limited to

items which are used infrequently and which are safely

stored in an area subjected to heat from an appliance.

Temperatures may be unsafe for some items, such as

volatile liquids, cleaners or aerosol sprays.

NEVER leave children alone or unsupewised near the

appliance when it is in use or is still hot.

NEVER allow children to sit or stand on any part of the

appliance as they could be injured or burned.

Children must be taught that the appliance and utensils

in it can be hot. Let hot utensils cool in a safe place, out

of reach of small children. Children should be taught

that an appliance is not a toy. Children should not be

allowed to play with controls or other parts of the unit.

About Your Appliance

In Case of Fire

Turn off appliance and ventilating hood to avoid

spreading the flame. Extinguish flame then turn on hood

to remove smoke and odor.

* Cooktop: Smother fire or flame in a pan with a lid or

cookie sheet.

NEVER pick up or move a flaming pan.

* Ovens: Smother fire or flame by closing the oven doors.

The oven vent is located at the base of the backguard.

Avoid touching oven vent area while oven is on and for

several minutes after oven is turned off. Some parts of

the vent and surrounding area become hot enough to

importantSurety

cause burns. After oven is turned off, do not touch the

oven vent or surrounding areas until they have had

sufficient time to cool.

Other potentially hot surfaces include cooktop, areas

facing the cooktop, oven vent, surfaces near the vent

opening, oven doors, areas around the oven doors and

oven windows.

Do not touch a hot oven light bulb with a damp cloth as

the bulb could break. Should the bulb break, disconnect

power to the appliance before removing bulb to avoid

electrical shock.

Do not use the cooktop or ovens as a storage area for

food or cooking utensils.

Cooking Safety

Always place a pan on a surface burner before turning it

on. Be sure you know which knob controls which

surface burner. Make sure the correct burner is turned

on and that the burner has ignited. When cooking is

completed, turn burner off before removing pan to

prevent exposure to burner flame.

Always adjust surface burner flame so that it does not

extend beyond the bottom edge of the pan. An

excessive flame is hazardous, wastes energy and may

damage the appliance, pan or cabinets above the

appliance.

NEVER leave a surface cooking operation unattended

especially when using a high heat setting or when deep

fat frying. Boilovers cause smoking and greasy spillovers

may ignite. Clean up greasy spills as soon as possible.

Do not use high heat for extended cooking operations.

NEVER heat an unopened container on the surface

burner or in the ovens. Pressure build-up may cause

container to burst, resulting in serious personal injury or

damage to the appliance.

Use dry, sturdy potholders. Damp potholders may cause

burns from steam. Dish towels or other substitutes

should never be used as potholders because they can

trail across hot surface burners and ignite or get caught

on appliance parts.

Always let quantities of hot fat used for deep fat frying

cool before attempting to move or handle.

Do not let cooking grease or other flammable materials

accumulate in or near the appliance, hood or vent fan.

Clean hood frequently to prevent grease from

accumulating on hood or filter. When flaming foods

under the hood, turn the fan on.

NEVER wear garments made of flammable material or

loose fitting or long-sleeved apparel while cooking.

Clothing may ignite or catch utensil handles.

Always place oven racks in the desired positions while

ovens are cool. Slide oven racks out to add or remove food,

using dry, sturdy potholders. Always avoid reaching into the

ovens to add or remove food. If a rack must be moved

while hot, use a dry potholder. Alwaysturn the ovens off at

the end of cooking.

Use care when opening the oven doors. Let hot air or

steam escape before moving or replacing food.

PREPARED FOOD WARNING: Follow food manufacturer's

instructions. If a plastic frozen food container and/or its

cover distorts, warps, or is otherwise damaged during

cooking, immediately discard the food and its container.

The food could be contaminated.

NEVER use aluminum foil to cover oven racks or oven

bottoms. This could result in risk of electric shock, fire, or

damage to the appliance. Use foil only as directed in this

guide.

Utensil Safety

Use pans with flat bottoms and handles that are easily

grasped and stay cool. Avoid using unstable, warped, easily

tipped or loose-handled pans. Also avoid using pans,

especially small pans, with heavy handles as they could be

unstable and easily tip. Pans that are heavy to move when

filled with food may also be hazardous.

Be sure utensil is large enough to properly contain food

and avoid boilovers. Pan size is particularly important in

deep fat frying. Be sure pan will accommodate the volume

of food that is to be added as well as the bubble action of

fat.

To minimize burns, ignition of flammable materials and

spillage due to unintentional contact with the utensil, do

not extend handles over adjacent surface burners. Always

turn pan handles toward the side or back of the appliance,

not out into the room where they are easily hit or reached

by small children.

Never let a pan boil dry as this could damage the utensil

and the appliance.

Follow the manufacturer's directions when using oven

cooking bags.

Only certain types of glass, glass/ceramic, ceramic or

glazed utensils are suitable for cooktop or oven usage

without breaking due to the sudden change in temperature.

Follow manufacturer's instructions when using glass.

ImponentSefet¥

This appliance has been tested for safe performance

using conventional cookware. Do not use any devices

or accessories that are not specifically recommended in

this guide. Do not use element covers, stovetop grills, or

add-on oven convection systems. The use of devices or

accessories that are not expressly recommended in this

manual can create serious safety hazards, result in

performance problems, and reduce the life of the

components of the appliance.

Cleaning Safety

Turn off all controls and wait for appliance parts to cool

before touching or cleaning them. Do not touch the

burner grates or surrounding areas until they have had

sufficient time to cool.

Clean appliance with caution. Use care to avoid steam

burns if a wet sponge or cloth is used to wipe spills on a

hot surface. Some cleaners can produce noxious fumes

if applied to a hot surface.

Self-Cleaning Ovens

Clean only parts listed in this guide. Do not clean door

gasket. The door gasket is essential for a good seal.

Care should be taken not to rub, damage, or move the

gasket. De not use oven cleaners of any kind in or

around any part of the self-clean oven.

It is normal for the cooktop of the range to become hot

during a self-clean cycle. Therefore, touching the

cooktop during a clean cycle should be avoided.

important Safety Notice

and Warning

The California Safe Drinking Water and Toxic

Enforcement Act of 1986 (Proposition 65] requires the

Governor of California to publish a list of substances

known to the State of California to cause cancer or

reproductive harm, and requires businesses to warn

customers of potential exposures to such substances.

Users of this appliance are hereby warned that the

burning of gas can result in low-level exposure to some

of the listed substances, including benzene,

formaldehyde and soot, due primarily to the incomplete

combustion of natural gas or liquid petroleum (LP] fuels.

Properly adjusted burners will minimize incomplete

combustion. Exposure to these substances can also be

minimized by properly venting the burners to the

outdoors.

Users of this appliance are hereby warned that when

the oven is engaged in the self-clean cycle, there may

be some low-level exposure to some of the listed

substances, including carbon monoxide. Exposure to

these substances can be minimized by properly venting

the oven to the outdoors by opening the windows and/

or door in the room where the appliance is located

during the self-clean cycle.

IMPORTANT NOTICE REGARDING PET BIRDS:

Never keep pet birds in the kitchen or in rooms where

the fumes from the kitchen could reach. Birds have a

very sensitive respiratory system. Fumes released during

an oven self-cleaning cycle may be harmful or fatal to

birds. Fumes released due to overheated cooking oil, fat,

margarine and overheated non-stick cookware may be

equally harmful.

Save These instructions for Future Reference

SurfaceCookln

Surface Controls

Pilotless ignition

Pilotless ignitioneliminates the

need for a constant standing

pilot light. Eachsurface burner

has a spark ignitor. Use care

when cleaning around the surface

burner.

If the surface burner does

not light, check if ignitor is

broken, soiled or wet.

BURNER CAP

Surface Control Knobs

Use to turn on the surface burners. An infinitechoice of heat

settings is available from Low to High. The knobs can be set

on or between any of the settings.

Graphics next to the knob identifywhich burner the knob

controls. Forexample, the graphic at left shows the

O 0 left front burner location.

Suggested Heat Settings

Low: Food maintains a temperature •

above 140° Fwithout continuing to •

cook. Food is heated on a higher ,/

flame size until it reaches this •

temperature and then the flame Low

size isreduced. Some cooking may

take place on the Low setting if the pan

is covered. ""

¸ •

iiili .,0h

OFI

An intermediate flame size is used to continue cooking. Food

will not cook any faster when a higher flame setting is used

than needed to maintain a gentle boil. Water boils at the

same temperature whether boiling gently or vigorously.

High: Use to bring liquid to a boil, or reach pressure in a

pressure cooker. Always reduce setting to a lower heat when

liquids begin to boil or foods begin to cook.

Setting the controls:

The size and type of cookware will affect the heat setting.

1. Placea pan on the burner grate.

• The burner flame may lift off or appear separated from

the port if a pan is not placed on the grate.

2. Push in and turn the knob counterclockwise to the Light

setting.

A clicking (spark:)sound will be heard and the burner

will light. (All five ignitorswill spark when any surface

burner knob is turned to the Light position.)

3. After the burner lights, turn knob to desired flame size.

• The ignitor will continue to spark until the knob is

turned past the Light position.

4. After cooking, turn knob to OFF. Remove pan.

Operating During a

Power Failure

1. Hold a lighted match to the desired surface burner head.

2. Push in and turn the control knob slowly to Light.

3. When the burner lights, adjust the flame to the desired

level.

¢ookln

Cooktop

To prevent the cooktop from discoloring or

staining:

* Clean cooktop after each use.

Wipe acidic or sugary spills as soon as the cooktop has

cooled as these spills may discolor the

- _[_ porcelain.

Unlike a range with standard gas burners,

this cooktop does not lift up nor is it

removable. De not attempt to lift the

cooktop for any reason.

Burner Grates

Tile grates must be properly positioned before cooking.

Lower the grates onto the range so that the bars match up

and the rubber feet located at the four corners of the grates

sit in the indentations on the cooktop.

Improper installation or removal of the grates may result in

chipping or scratching of the cooktop. It may also cause pans

to be unsteady on the grates.

Sealed Burners

The sealed burner bases of your range are secured to the

cooktop and are not designed to be removed. Since the

burners are sealed into the cooktop, boilovers or spills will not

seep underneath the cooktop.

However, the burner base should be cleaned after each use.

The cap portion of the burner is easily removed for cleaning.

(See page 17 for cleaning directions.)

The burner caps must be correctly placed on the burner base

for proper operation of the burner.

High Performance Burners

There is one 16,000 BTU_high speed burner on your range,

located in the left front position. There is a 12,000 BTU_

burner located in the right front position. These burners offer

higher speed cooking that can be used to quickly bring water

to a boil and for large-quantity cooking.

Simmer Burner

This burner islocated in the center position. The

simmer burner offers a lower BTU_flame for delicate

sauces or melting chocolate.

BTU ratings will vary when using LP gas.

0 0

Do not operate the burners without a pan on the grate.

The grate's porcelain finish may chip without a pan to

absorb the heat from the burner flame.

Use care when stirring food in a pot/pan sitting on the burner

grate. The grates have a smooth finish for ease of cleaning.

The pot/pan will slide if the handle is not held. This may result

in spilling of hot food items and may be a burn hazard.

Although the burner grates are durable, they will gradually

lose their shine and/or discolor, due to the high temperatures

of the gas flame.

Notes:

* A properly adjusted burner with clean ports will light

within a few seconds. If using natural gas, the flame

will be blue with a deeper blue inner cone.

If the burner flame is yellow or is noisy, the air/gas

mixture may be incorrect. Contact a service technician

to adjust. (Adjustments are not covered by the

warranty.)

With LP gas, slight yellow tips on the flames are

acceptable. This is normal and adjustment is not

necessary.

With some types of gas, you may hear a "popping"

sound when the surface burner isturned off. This is a

normal operating sound of the burner.

" If the control knob is turned very quickly from High to

Low, the flame may go out, particularly if the burner is

cold. If this occurs, turn the knob to the OFF position,

wait several seconds and relight the burner.

" The flame should be adjusted so it does not extend

beyond the edge of the pan.

Control Panel

Clean -.......

Lower Oven Bake : \,

Keep

E F G H I J K

Thecontrol panel isdesigned for easeinprogramming. Thedisplaywindow on thecontrol shows time of day,timer and ovenfunctions.

Control panel shown includesmodel specific features. (Styling may vary depending on model.]

iJ!!i!i!i!i!i!_

_i_ii,i!i!,i!i!,i!i!,i!i!,i!i!,i!i

Bake

KeepWarm

Broil

Clean

CANCEL

Delay

Cook & Hold

Timer

Clock

Oven Light

Less- or

More+

Use for baking and roasting.

Use to keep cooked food warm in

oven.

Use for broiling and top browning.

Use to set self-clean cycle.

Cancels all operations except timer

and clock.

Programs the oven to start baking

or cleaning at a later time.

Bakes for a preset time, then keeps

food warm for 1 hour.

Sets timer.

Use to set time-of-day clock.

Use to turn the oven light on or off.

Enters or changes time, oven

temperature. Sets HI or LO broil.

Using the Touchpads

• Pressthe desired pad.

• Pressthe More+ or Less- pad to enter time or temperature.

• A beep will sound when any pad is touched.

° A double beep will sound if a programming error occurs.

Important: Four seconds after pressing the More+ or Less-

pad, tile time or temperature will automatically be entered. If

more than 30 seconds elapse between touching a function

pad and the More+ or Less- pad, the function will be

canceled and the display will return to the previous display.

Clock

Tire clock can be set to display time in a 12-hour or 24-hour

format, Tile clock is set at the factory for the 12-hour format,

To change the clock to 24=hour format:

1. Pressand hold the upper oven CANCEL

and Delay pads for several seconds.

2. Pressthe More+ or Less - pad to select

12 or 24 hour.

3. Set the time of day following the

directions below.

To set the Clock:

1. Presstire Clock pad.

• The colon (:) flashes in the display.

2. Press More+ or Less- pad to set the time

of day.

° Colon continues flashing.

3. Pressthe Clock pad again or wait four

seconds.

• The colon stops flashing.

When electrical power is supplied or after a power

interruption, the last clock time before power was

interrupted will flash.

To recall the time of day when another time function is

showing, press the Clock pad.

Clock time cannot be changed when the oven has been

programmed for Bake, Clean, Delay or Cook & Hold.

To cancel the Clock display:

If you do not want the time of day to display:

Press and hold the upper oven CANCEL

and Clock pads for several seconds. The

time of day will disappear from the display.

When the clock display is canceled, press

the Clock pad to briefly display the time of

day.

To restore the Clock display:

Press and hold the upper oven CANCEL and Clock pads for

several seconds. The time of day will reappear in the display.

Timer

Tile timer can be set from one minute (1:00) up to 11 hours

and 59 minutes (11:59).

The timer can be used independentlyof any other oven

activity. It can also be set while another oven function is

operating.

The timer does not control the oven.

To set the Timer:

1. Pressthe Timer pad.

• "0:00" lights in the display.

• "Timer" will flash.

2. Pressthe More+ or Less= pad until the

correct time appears in the display.

• "Timer" will continue to flash.

3. PressTimer pad again or wait four seconds.

° The time begins counting down.

° The last minute of the timer countdown will be displayed

as seconds.

4. At the end of the set time, three long beeps will sound.

To cancel the Timer:

1. Pressand hold the Timer pad for three seconds.

2. Pressthe Timer pad and set the time to 0:00.

Locking the Control

and Oven Doors

Tile touchpads and oven doors can be locked for safety,

cleaning, or to prevent unwanted use. They will not function

when locked.

If the oven is currently in use, the touchpads and doors

cannot be locked.

The current time of day will remain in the display when the

controls are locked.

To lock both doors:

Press and hold the upper oven CANCEL

and Cook & Hold pads for three seconds.

"Lock" flashes in the display while both

oven doors lock. Once complete, "Lock"

stops flashing.

"OFF" is displayed for 10 seconds whenever

a pad is touched.

To unlock both doors:

Press and hold the upper oven CANCEL and Cook & Hold

pads for three seconds.

"Lock" flashes and then disappears from the display.

"OFF" appears in the display for several seconds while

doors are unlocking.

Important: The touchpads and oven doors cannot be locked

if the oven temperature is 400° For above.

Fault Codes

"Bake" or "Lock" may flash rapidly in tile display to alert you if

there is an error or a problem. If "Bake" or "Lock" flash in the

display, press CANCEL pad. If "Bake" or "Lock" continue to

flash, disconnect power to the appliance. Wait a few minutes,

and then reconnect power. If the flashing still continues,

disconnect power to the appliance and call an authorized

servicer.

Adjusting the Sound Level

Tile factory default setting for sound ismedium (MEd), but it

can be changed to low (Lo) or high (HI). To change the

setting:

1. Pressand hold More+ and upper oven CANCEL pads for

three seconds. A beep will sound and the current sound

level ("Lo', "MEd" or "HI") will appear in the display.

2. Press More+ pad to increase sound level or the Less-

pad to decrease sound level.

3. Wait four seconds and the new setting will be accepted.

4. If the More+ or Less- pad is not pressed within 30 sec-

onds, the control will return to the existing settings.

Changing Temp °F/°C

Tile factory default setting for temperature is Fahrenheit. To

change the setting:

1. Pressand hold the upper oven Bake and CANCEL pads

for three seconds. A beep will sound and the current

setting (°F or °C)will appear in the display.

2. PresstheMore+ or Less- pad to change the setting

between °F and °C.

3. Wait four seconds and the new setting will be accepted.

4. If the More+ or Less- pad is not pressed within 30

seconds, the control will return to the existing settings.

Return To Factory Default

Settings

Tile control car/be reset to tile factory default settings. To

return to the default settings:

1. Pressand hold upper oven Keep Warm and CANCEL

pads for three seconds. A single beep will sound and "dEF'

Cdefaul0will appear in the display.

2. Pressthe More+ pad to choose the factory settings. "cLr"

(clear) will appear in the display.

3. Wait four seconds and the factory settings will be

accepted.

4. If the More+ or Less- pad is not pressed within 30

seconds, the control will return to the existing settings.

Setting Upper and Lower

Oven Functions

Baking

To set bake: .........................

1. Pressthe Bake pad for desired oven. Bake

, "Bake" will flash.

• "000°'' will flash in the display.

2. Select the oven temperature. The oven

temperature can be set from 170° to 550°. Press i

orpressand holdtileMere+ orLess-pad. '_ :;

, "350°" will light when either pad is first pressed.

• Press the More+ pad to increase the temperature.

• Press the Less- pad to decrease the temperature.

3. Press Bake pad again or wait four seconds.

, "Bake" will stop flashing and light in the display.

• "Preheat" will light in the display.

• 100° or the actual oven temperature will display. The

temperature will rise in 5° increments until the preset

temperature is reached.

Allow selected oven to preheat for 8-15 minutes.

• When the set oven temperature is reached, one long

beep will sound.

• To recall the set temperature during preheat, press the

Bake pad.

To change the oven temperature during preheat, press

Bake once and reset temperature.

Placefood in the oven.

Check cooking progress at minumum cooking time. Cook

longer if needed.

When cooking is finished, press CANCEL pad. ('CAN(_Eb

Removefood from the oven.

Baking Differences Between Your Old

and New Oven

It isnormal to notice some baking time differences between a new

oven and an old one. See Adjusting the Oven Temperature on

page 11.

Notes:

Allow at least 1/2-inch between the baking pan or

casserole and the top element in the upper oven.

Loaf, angel food or bundt pans are not recommended in

the upper oven.

Do not use temperatures below 140° Fto keep food

warm or below 200° Ffor cooking. Forfood safety

reasons, lower temperatures are not recommended.

To change the oven temperature during cooking, press

the Bake pad and then the More+ or Less- pad until

you reach the desired temperature.

When preheating with a baking/pizza stone inside

the upper oven, do not set oven above 400 ° F. To

use baking/pizza stones at temperatures above 400 °

in the upper oven, put stone in after the preheat

beep.

If you forget to turn off tile oven, it will automatically turn

off at the end of 12 hours. If you wish to deactivate the

Automatic Shut-off/Sabbath Mode feature, see page 13.

Cook & Hold

Cook & Hold allows you to bake for a preset amount of time,

followed by a one-hour Keep Warm cycle.

To set Cook & Hold:

1. Pressthe Cook & Hold pad once for

upper oven or twice for lower oven.

Cont.

• "Bake" and "Hold" flash.

• "000°'' will flash in the display.

2. Select the oven temperature. The oven _:i:

besetfrom,70°to

temperature

can

Pressor press and hold the More+ or Less- pa

• Press the More+ pad to increase the temperature.

° Press the Less- pad to decrease the temperature.

3. Press Cook & Hold pad again ORwait four seconds to set

cook time.

• "Time" flashes.

• "0:00" flashes in the display.

4. Enter the amount of time you want to cook by pressing the

More+ or Less- pad. Time can be set from 10 minutes

(10:00) to 11 hours, 59 minutes (11:59).

• "Bake", "Preheat" and "Hold" light in the display.

• The cooking time will start counting down.

° "1O0°'' or actual oven temperature will light in the

display.

When the cooking time has elapsed:

• Three beeps will sound.

° "Bake" will turn off.

° "Hold" will light.

After one honr in HOLD WARM:

° The oven will turn off. Three beeps will sound.

To cancel Cook & Hold at any time: _./_. ,_

Pressthe CANCEL pad. Removefood from oven. _,,_'_/'_l_='l-L/j

Delay Cook & Hold

When using Delay, the oven begins to cook later in the day.

Set the amount of time that you want to delay before the oven

turns on and how long you want to cook. The oven begins to

heat at the selected time and cooks for the specified length of

time, then keeps food warm for one hour.

Delay time can be set from 10 minutes (10:00) to 11 hours, 59

minutes C11:59).

To set a Delayed Baking cycle:

1. Press the Delay pad once for upper oven or

twice for lower oven.

• "dLY" and "0:00" flash in the display.

2. Press the More+ or Less- pad to set the

amount of time you want to delay the

Cook & Hold cycle.

While "dLY" isstill flashing:

3. Press the Cook & Hold pad.

° %00°" flashes in the display.

° "Bake" and "Hold" flash.

4. Press More+ or Less= pad to enter oven temperature.

• "Bake" flashes.

° After several seconds, "0:00" and "Time" flash.

° "Bake" and "Hold" remain steady.

5. Press More+ or Less= pad to set the baking time.

° "Time" flashes.

° After several seconds, the delay time will count down.

• "dLY", "Bake" and "Hold" light in the display.

When the Delay time has expired:

° "dLY" will turn off.

• Baking time and temperature are displayed.

• "Bake" and "Hold" are displayed.

When the oven starts:

• The baking time will count down.

• "dLY" will turn off.

° "Bake" and "Hold" will remain lit.

To cancel:

Press the CANCEL pad.

° All timed and untimed cooking functions will be

canceled.

° The time of day will reappear in the display.

Important:

Do not use delayed baking for items that require a

preheated oven, such as cakes, cookies, and breads.

Do not use delayed baking if oven is already hot.

Keep Warm

Forsafely keeping foods warm or for warming breads and

plates.

To set Keep Warm:

1. Press the Keep Warm pad for the

appropriate oven.

• "Warm" flashes.

• "000°'' flashes in the display.

2. Select the Keep Warm temperature. The Keep

Warm temperature can be set from 145° to

190°. Pressor press and hold the More+ or

Less= pad.

• 170°will light when either pad isfirst pressed.

• Pressthe More+ pad to increasethe temperature.

° Pressthe Less= pad to decrease the temperature.

"Warm" and the temperature will be displayed while Keep

Warm isactive.

Keep

Warm

To cancel Keep Warm:

1. Press the CANCEL pad.

2. Remove food from the oven.

Notes:

• Foroptimal food quality, ovencooked foods should be kept

warm for no longer than 1 to 2 hours.

° To keep foods from drying, cover loosely with foil or a lid.

• To warm dinner rolls:

- cover rolls loosely with foil and place in oven.

- press Keep Warm and More+ pads to set 170° F.

- warm for 12-15 minutes.

• To warm plates:

- place 2 stacks of up to four plates each in tile oven.

- press Keep Warm and More+ pads to set 170° F.

- warm for five minutes, turn off the oven and leaveplates

in the oven for 15 minutes more.

- use only oven-safe plates, check with the manufacturer.

- do not set warm dishes on a cold surface as rapid

temperature changes could cause crazing or breakage.

Adjusting the Oven Temperature

Oven temperatures are carefully tested for accuracy at the

factory. It is normal to notice some baking or browning

differences between a new oven and an old one. As ranges

get older, the oven temperature can shift.

You may adjust the oven temperature if you think the oven is

not baking or browning correctly. To decide how much to

change the temperature, set the temperature 25° higher or

lower than your recipe recommends, then bake. The results

of the "test" should give you an idea of how much to adjust

the temperature.

To adjust the oven temperature:

Press the appropriate Bake pad.

Enter 550° by pressing the More+ pad.

Press and hold the Bake pad for several

seconds or until "0°'' and "AdJ" (which

signifies 'adjust') appear in the display.

If the oven temperature was previously adjusted, the

change will be displayed. For example, ifthe oven

temperature was reduced by 15° the display will

show "- 15°".

Bake

4. Press the Mare+ or Less= pad to adjust the temperature.

Each time a pad is pressed, the temperature changes by

5°. The oven temperature can be increasedor decreased

by 5° to 35°.

5. The time of day will automatically reappear in the display.

You do not need to readjust the oven temperature if there

isa power failure or interruption.Broiling and cleaning

temperatures cannot be adjusted.

Broiling (upper oven only)

To set Broil:

1. Press the Broil pad.

• "Broil" and "SEt" flash in the display. Broil

2. Press the More+ or Less- pad once to set HI broil. Press

the More+ or Less- pad twice to set LO broil.

• HI or LO will be displayed.

• Select HI broil (550° F)for normal broiling. Select

LO broil (450° F)for low-temperature broiling of longer

cooking foods such as poultry.

3. After four seconds, the oven will start.

• "Broil" and HI or LO will remain lit.

4. Foroptimum browning, preheat broil burner for five

minutes before adding food.

5. Placefood in the oven. Close oven door.

6. Most meat should be turned once about halfway through

cooking.

7. When food is cooked, press the CANCEL pad. _,"N

Removefood and broiler pan from the oven.

• The time of day will reappear in the display.

Notes:

For best results when broiling, use a two-piece broiler

pan.

HI broil is used for most broiling. Use LO broil when

broiling longer cooking foods to allow them to cook to

well done stage without excessive browning.

Broil times may be longer when the LO broil temperature

is selected.

Never cover broiler pan insert with aluminum foil. This

prevents fat from draining to the pan below.

Broiling can be done on the oven rack or remove oven

rack and place broiler pan on the oven bottom.

If more than 30 seconds elapse between pressing the

Broil pad and the More+ or Less- pad, the oven will not

be set and the display will return to the previous display.

Most foods should be turned halfway through broiling

time.

For a browned/seared exterior and rare interior, it may be

necessary to decrease cook time on side one.

Broiling Chart - Broil times are based on a five minute preheat.

Beef

Steak, 1" thick,

4 oz. Hamburgers, 3/4" thick (up to 12)

4 oz. Hamburgers, 3/4" thick (up to 6)

Chicken

Bone-in, skin-on breast

Pieces

Fish

Filets

Steaks, 1"thick

Pork

Chops, 1" thick

Garlic Bread

on rack

oven bottom

on rack

8 - 14 (medium)

15 - 19 (well)

12 - 15 (well)

1" thick oven bottom LO 1 - 4

When broiling fish, spray broil pan insert with cooking oil. Do not turn fish filets.

** Broiling times are approximate and may vary depending on the thickness of the food. Turn meat halfway through cooking times.

oven bottom LO 25 - 35

oven bottom LO 8- 11

oven bottom LO 10 - 15

on rack HI 18 - 25

Automatic Shut-Off/Sabbath

Mode

The ovens will automatically turn off after 12 hours if you

accidentally leave them on. The oven MUST be set for a

bake operation before setting the Automatic Shut-off/

Sabbath Mode.

To cancel the 12=hour shut=off and run the

oven continuously for 72 hours:

1. Set the oven to bake (see page 9).

2. Press and hold the Clock pad for five seconds.

• "SAbbAth"* will be displayed and flash for five seconds.

• "SAbbAth" will then be displayed continuously until

turned off or until the 72-hour time limit is reached.

• "Bake" and the oven temperature will also be displayed

ifa bake setting isin use while the oven is in Sabbath

Mode.

All other functions EXCEPTBAKE (Timer, Keep Warm,

Clean, etc.) are locked out during the Sabbath Mode.

To cancel Bake when in Sabbath Mode:

Press the CANCEL pad.

• "Bake" and the oven temperature will turn

off in the display.

• "SabbAth" appears in the display.

• "Time" no longer appears in the display.

To cancel the Sabbath Mode:

1. Pressthe Clock pad for five seconds.

• "SAbbAth" will flash for five seconds.

• The time of day will return to the display.

2. After 72 hours, the Sabbath Mode will end.

• "SAbbAth" will flash for five seconds.

• The time of day will return to the display.

Pilotless ignition

Your range isequipped with pilotless ignition.With this type of

ignitionsystem, the gas automatically shuts off and the oven

will not operate during a power failure.

A lighted match will not light the oven burner. No attempt

should be made to operate the oven during a power

failure.

Oven Vent

When the oven is in use the area near the vent may become

hot enough to cause burns. Never block the vent opening.

The oven vent is located below the backguard vent shield

on your range.

When high moisture foods are cooked in the upper oven, steam

may be visible coming from the oven vent. This is normal.

OVEN VENT

CATION DO not place

plastics near the

vent opening as

heat from the vent

could distort or

melt the plastic.

Oven Lights

The oven lights automatically come on whenever an oven door

is opened. When the door is closed, press the Oven Light pad

to turn the oven lights on or off. A beep will

sound every time the Oven Light pad is pressed.

Oven Bottom

Protect oven bottom against spillovers, especially acidic or

sugary spills, as they may discolor the porcelain enamel. Use

the correct pan size to avoid spillovers and boilovers. Do not

place aluminum foil directly on either oven bottom. Do

not place pans on the oven bottom while baking or

roasting in the upper or lower oven. You may place pans

on oven bottom for broiling in upper oven only.

* Important: "SAbbAth" appears in the display on two lines: SAb.

bath

Notes.-

• Sabbath Mode can be turned on only when the ovens

are on.

• All prompts, messages and beeps are deactivated when

Sabbath Mode is active.

° Sabbath Mode cannot be turned on if the touchpads are

locked out or when the doors are locked.

• The automatic door lock does not operate during the

Sabbath Mode.

• If the oven light is desired while in Sabbath Mode, it

must be turned on before the Sabbath Mode is started.

• When the Sabbath Mode is started, no preheat beep will

sound.

• Pressing CANCEL pad will cancel a bake cycle, however the

control will stay in the Sabbath Mode.

° If power fails, the ovens will power up in Sabbath Mode

with 72 hours remaining and no cycle active,

Oven Racks

All racks are designed with a lock-stop edge.

Upper oven II /_ \\_

• Is equipped with one rack and rack

position.

• When pulling the upper oven rack out to

remove or check food, grasp the top edge of the rack.

Lower oven

• Is equipped with one RollerGlideTM rack and one flat rack.

RACK 3: Use for most one-rack baking of baked goods on a

cookie sheet or jelly roll pan, layer cakes, fruit pies, or frozen

convenience foods.

RACK 2: Use for roasting small cuts of meat, casseroles,

baking loaves of bread, bundt cakes, sheet cakes or custard

pies and two-rack baking of biscuits, cookies and layer cake.

RACK 1: Use for roasting large cuts of meat and poultry,

frozen pies, dessert souffles or angel food cake.

MULTIPLE RACK COOKING:

]'we rack: Userack positions 2 and 4 for layer cakes and

cookies, or 2 and 5 for biscuits and cookies.

To remove oven racks:

Pull rack straight out until it stops

at the lock-stop position; lift up

on the front of the rack and pull

out.

• For RollerGlideTM rack, pull both

the rack glide and rack base out

together.

To replace oven racks:

° Placerack on the rack support in tile oven; tilt tile front end

up slightly; slide rack back until it clears the lock-stop

position; lower front and slide back intothe oven.

Baking with the RollerGuide TMRack

• When baking on two racks, use tile RollerGlideTM rack in

tile upper rack position, and tile flat rack in tile lower rack

position.

Half Rack Accessory

(Lower oven only)

A half rack, to increaseoven

capacity, is available as an

accessory. It fits in the left, upper

portion of the oven and provides

space for a vegetable dish when a

large roaster ison the lower rack.

Contact your Maytag dealer for the

"HALFRACK" Accessory Kit or call

1-877-232-6771 USA and Canada to order.

Rack Positions (loweroven)

RACK 5: Use for two-rack baking of biscuits and cookies.

RACK 4: Use for two-rack baking of layer cake and cookies.

Cleenin

Self-Clean Oven

The self-clean cycle uses above-normal cooking temperatures

to automatically clean the oven interior.

The oven should be cleaned regularly by wiping up spillovers

to prevent excessive smoke and flare-ups. [:lo not allow a

heavy build-up of soil to accumulate in the oven.

During the cleaning process, the kitchen should be well

ventilated to get rid of normal odors associated with cleaning.

Before Self=Cleaning

1. Turn off the oven light before cleaning. Tile light may burn

out during the clean cycle.

2. Remove broiler pan, all pans, and oven racks from the

oven. The oven racks will discolor and may not slide easily

after a self-clean cycle if they are not removed.

3. Clean oven frame, door frame, area

outside of gasket, and around the

opening in the door gasket with a

nonabrasive cleaner such as Bon

Ami* or detergent and water. The

self-cleaning process does not

clean these areas. They should be

cleaned to prevent soil from baking on during the clean

cycle. (The gasket is the seal around the oven door and

window.}

4. To prevent damage, do not clean or rub the gasket around

the oven door. The gasket is designed to seal in heat

during the clean cycle.

5. Wipe up excess grease or spillovers from the oven bottom.

This prevents excessive smoking, flare-ups or flaming

during the clean cycle.

6. Wipe up sugary and acidic spillovers such as sweet

potatoes, tomato, or milk-based sauces. Porcelain enamel

is acid-resistant, not acid-proof. The porcelain finish may

discolor if acidic spills are not wiped up before a self-

clean cycle.

Important:

• Oven temperature must be below 400° Fto program a

clean cycle.

• Only one oven can be cleaned at a time.

Both oven doors lock when either oven is being cleaned.

To set Self=Clean:

1. Close the oven door.

Clean

Pressthe Clean pad. ....................................

• "Clean" and "SEt" flash in the display.

If the door is not closed within 25 seconds, the self-

cleaning operation will be canceled and the display will

return to the time of day.

3. Pressthe More+ or Less- pad.

• "MEd" for medium amount of soil (3 hours}

appears in the display.

If the door is not closed, "door" will appear in

the display. After 45 seconds, three beeps will

sound, the self-cleaning operation will be canceled

and the display will return to the time of day.

4. Pressthe More+ twice for heavy soil (4 hours}.

° "HVy" will be displayed.

Press Less= pad twice for light soil {2 hours}.

• "LITE" will be displayed.

Choosing the soil level of the oven automatically programs

the self-cleaning time. "Lock" flashes in the display.

5. After four seconds, the oven will start cleaning.

• The cleaning time will start counting down in the display.

• "Lock" will appear in the display and will flash until the

doors are locked. "Lock" will then remain lit.

° "Clean" will remain lit in the display.

To Delay a Self=Clean Cycle:

1. Pressthe Delay pad once for upper

oven and twice for lower oven.

• "dLY" flashes.

• %:00" flashes in the display.

Pressthe More+ or Less- pad to set the

amount of time you want to delay the cycle.

Delay time can be set from ten minutes

(10:00} to 11 hours, 59 minutes (11:59}.

Cont.

*Brand names for cleaning products are registered trademarks ofthe respective manufacturers.

Cleantn

3. Press the apropriate Clean pad while

"dLY" is flashing. Clean

• "Clean" and "Set" will flash.

If the door is not closed within 25 seconds, the

self-cleaning operation will be canceled and the display

will return to the time of day.

4. Press the More+ or Less- pad.

• "MEd" for medium amount of soil (3 hours:)

is displayed.

If the door is not closed, "door" will appear in

the display. After 45 seconds, three beeps will

sound, the self-cleaning operation will be canceled

and the display will return to the time of day.

5. Press the More+ pad twice for heavy soil (4 hours:).

"HVy" will bedisplayed.

Press the Less- pad twice for light soil (2 hours:).

"LITE" will be displayed.

Choosing the soil level of the oven automatically programs

the self-cleaning time.

6. After four seconds, "Clean", "dLY" and "Lock" will appear

in the display to show that the oven is set for a delayed

clean operation. The delay time is displayed and will begin

to count down.

When the Self=Clean cycle starts:

• "dLY" will turn off.

• "Clean", "Hours", "Lock" and the clean time will appear

in the display.

To cancel the Self-Clean cycle:

Press the CANCEL pad. (CANCEL)

• All words disappear from the display.

• All functions are canceled.

• The time of day appears in the display.

During the Self=Clean Cycle

When "Lock" shows in the display, both oven doors are

locked. To prevent damage to the doors, do not force the

doors open when "Lock" isdisplayed.

Smoke and Smells

You may see some smoke and smell an odor the first few

times the oven is cleaned. This is normal and will lessen in

time.

Smoke may also occur if the oven is heavily soiled or if a

broiler pan was left in the oven.

Sounds

As the oven heats, you may hear sounds of metal parts

expanding and contracting. This is normal and will not

damage the oven.

After Self=Cleaning

About one hour after the end of the self-clean cycle, "Lock"

will turn off. The doors can then be opened.

Some soil may leave a light gray, powdery ash. Remove

itwith a damp cloth. If soil remains after wiping, that means

the clean cycle was not long enough. The soil will be

removed during the next clean cycle.

If oven racks were left in the oven and do not slide

smoothly after a clean cycle, wipe racks and rack supports

with a small amount of vegetable oil to make them easier to

move.

Fine lines may appear in the porcelain because it went

through heating and cooling. This isnormal and will not

affect performance.

A white discoloration may appear after cleaning if acidic

or sugary foods were not wiped up before the self=clean

cycle. This discoloration isnormal and will not affect

performance.

Notes:

° If the oven door is left open, "door" will appear in the

display until the door is closed.

• If more than five seconds elapse between pressing the

Clean pad and the More+ or Less- pad, the program will

automatically return to the previous display.

• The oven door will be damaged if the oven door is

forced to open when "Lock" is still displayed.

Cleantn

Cleaning Procedures

Brand names are registered trademarks of the

respective manufacturers.

To order call 1-877-232-6771 USAor

1-808-888-8408 Canada.

Broiler Pan

and Insert

Burner Caps and

Sealed Gas

Burners

Burner Grates =

Porcelain on

Cast Iron

Clock and

Control Pad

Area

Control Knobs

Cooktop and

Control Panel =

Porcelain Enamel

Side Panels,

and Door

Handles =

Painted Enamel

Never cover insert with aluminum foil as this prevents the fat from draining to the pan below.

• Place soapy cloth over insertand pan; let soak to loosen soil.

• Wash in warm, soapy water. Use scouring pad to remove stubborn soil.

• Broiler pan and insertcan be cleaned in dishwasher.

Removable Burner Heads

• Allow burner to cool. Remove burner cap and wash in soapy water with a plastic scouring pad. For

stubborn soils, clean with a soap-filled, nonabrasive pad or Cooktop Cleaning Creme_

(Part #2OOOOOOl}_ and a sponge.

• Do not clean in the dishwasher or self-cleaning oven.

Sealed Gas Burners

• Clean frequently. Allow burner to cool. Clean with soap and plastic scouring pad. Forstubborn soils,

clean with a soap-filled, nonabrasive pad. Do not enlarge or distort holes.

• Be careful not to get water into burner ports.

• Use care when cleaning the ignitor. If the ignitor iswet or damaged the surface burner will not light.

° Wash with warm, soapy water and a nonabrasive, plastic, scrubbing pad. For stubborn soils,

clean with a soap-filled, nonabrasive, plastic pad or Cooktop Cleaning Creme_ (Part #20000001} _*

and a sponge. If soil remains, re@ply Cooktop Cleaning Creme,cover with a damp paper towel

and soak for 30 minutes. Scrub again, rinse and dry.

• Do not clean in the dishwasher or self-cleaning oven.

• To activate "Control Lock" for cleaning, see page 8.

• Wipe with a damp cloth and dry. Do not use abrasive cleaning agents as they may scratch the finish.

• Glass cleaners may be used ifsprayed on a cloth first. DO NOTspray directly on control pad and

display area.

• Remove knobs in the OFFposition by pulling forward.

• Wash, rinse and dry. Do not use abrasive cleaning agents as they may scratch the finish.

° Turn on each burner to be sure the knobs have been correctly replaced.

Porcelain enamel is glass fused on metal and may crack or chip with misuse. It is acid-resistant, not acid-

proof. All spillovers, especially acidic or sugary spillovers, should be wiped up immediately with a dry cloth.

• When cool, wash with soapy water, rinse and dry.

• Never wipe off a warm or hot surface with a damp cloth. This may cause cracking or chipping.

• Never use oven cleaners, abrasive or caustic cleaning agents on exterior finish of range.

• When cool, wash with warm soapy water, rinse and dry. Never wipe a warm or hot surface with a damp

cloth as this may damage the surface and may cause a steam burn.

• Forstubborn soil, usemildly abrasive cleaning agents such asbaking soda paste or BonAmi*. Do not use

abrasive cleaners such assteel wool pads or oven cleaners. These products will scratch or permanently

damage the surface.

Important: Use a dtytowel or cloth to wipe up spills, especially acidic or sugary spills. Surface may

discolor or dull if soil is not immediately removed. Thisis especially important for white surfaces.

Cleantn

Oven Window

and Door = Glass

• Avoid using excessive amounts of water which may seep under or behind glass, causing staining.

• Wash with soap and water. Rinse with clear water and dry. Glass cleaner can be used if sprayed on a

cloth first.

• Do not useabrasive materials such asscouring pads, steel wool or powdered cleaners astheywill scratch

glass.

Oven Interior • Follow instructions on pages 15-16 to set a self-clean cycle.

Oven Racks

Stainless Steel

(select models]

Clean with soapy water.

Removestubborn soil with cleansing powder or soap-filled scouring pad. Rinse and dry.

Racks will permanently discolor and may not slide out smoothly if left in the oven during a self-clean

operation. If this occurs, wipe the rack and embossed rack supports with a small amount of vegetable oil

to restore ease of movement, then wipe off excess oil.

* DO NOT USEANY CLEANING PRODUCT CONTAiNiNG CHLORINE BLEACH.

* DO NOT USEABRAS/VE OR ORANGE CLEANERS.

° ALWAYS WiPE WiTH THEGRAIN WHEN CLEANING.

* Daily Cleaning/Light Soil -- Wipe with one ofthe following - soapywater, white vinegar/water solution,

Formula 409 Glass and Surface Cleaner* or a similar glass cleaner - using a sponge or soft cloth.

Rinse and dry. To polish and help prevent fingerprints, follow with Stainless Steel Magic Spray*

(Part No. 20000008__*.

, Moderate/Heavy Soil -- Wipe with one of the following -Bon Ami, Smart Cleanser, or Soft Scrub* -

using a damp sponge or soft cloth. Rinse and dry. Stubborn softs may be removed with a damp multi-

purpose Scotch-Brite _pad; rub evenly with the grain. Rinseand dry.To restore luster and remove streaks,

follow with Stainless Steel Magic Spray*.

, Discoloration -- Using a damp sponge or soft cloth, wipe with Cameo Stainless Steel Cleaner_.Rinse

immediately and dry. To remove streaks and restore luster,follow with Stainless Steel Magic Spray*.

Brand names for cleaning products are registered trademarks of the respective manufacturers.

_ To order direct, call 1-877-232-6771 USAor 1-860-688-8408 Canada.

Oven Doors

Both the upper and lower oven doors are removable.

To remove:

1. When cool, open the oven door to the broil stop position

(opened about four inches:).

2. Grasp door at each side. Be not use the door handle to

lift door.

3. Lift up evenly until door clears hinge arms.

Oven Windows

To protect the oven door window:

1. Do not use abrasive cleaning agents such as steel wool

scouring pads or powdered cleansers as they may scratch

the glass.

2. Be not hit the glass with pots, pans, furniture, toys, or

other objects.

3. Do not close the oven door until the oven racks are in

place.

Scratching, hitting, jarring or stressing the glass may weaken

its structure causing an increased risk of breakage at a later

date.

Upper and Lower Oven Lights

To replace:

1. Grasp door at each side.

2. Align slots in the door with the hinge arms on the range.

3. Slide the door down onto the hinge arms until the door is

completely seated on the hinges. Push down on the top

corners of the door to completely seat door on hinges.

Door should not appear crooked.

Important: The oven door on a new range may feel "spongy"

when itis closed. This isnormal and will decrease with use.

To assure the proper replacement bulb is used, order bulb

from Maytag. Call 1-877-232-6771 USAand 1-800-688-8408

Canada, ask for part number 74009925 - halogen bulb.

To replace oven light bulbs:

1. Disconnect power to the range.

2. When oven iscool, use fingertips to grasp edge of bulb

cover. Pull out and remove.

3. Carefully remove old bulb by pulling straight out of

ceramic base.

4. To avoid damaging or decreasing the life of the new bulb,

do not touch the bulb with bare hands or fingers. Hold

with a cloth or paper towel. Push new bulb prongs straight

into small holes of ceramic base.

5. Replace bulb cover by snapping into place.

6. Reconnect power to range. Reset clock.

La page charge ...

Maytag MGR6775BDW - Gas Double Oven Range Mode d'emploi

Marque: Maytag

Modèle: MGR6775BDW - Gas Double Oven Range

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Maytag MGR6775BDW - Gas Double Oven Range User guide
español: Maytag MGR6775BDW - Gas Double Oven Range Guía del usuario

Documents connexes

Autres documents

Jenn-Air JDR8880RDB Le manuel du propriétaire