Monogram ZISS480NHSS Guide d'installation

Monogram
Marque
Monogram
Modèle
ZISS480NHSS
Catégorie
Frigos
Taper
Guide d'installation
Side by Side Refrigerators
Design Guide
With Installation Instructions
Installation
Instructions
09-14 GE
monogram.com
31-49057
224D1889P015
Safety Information
2
BEFORE YOU BEGIN
Read these instructions completely and carefully.
• IMPORTANT – Save these instructions for
local inspector’s use. Observe all governing codes
and ordinances.
• Note to Installer – Be sure to leave these
instructions with the Consumer.
• Note to Consumer – Keep these instructions with
your Owner’s Manual for future reference.
If you received a damaged refrigerator, you should
immediately contact your dealer or builder.
Skill Level – Installation of this refrigerator requires
basic mechanical, carpentry and plumbing skills.
Proper installation is the responsibility of the installer.
Product failure due to improper installation is not
covered under the GE Appliance Warranty.
See the Owner’s Manual for warranty information.
WARNING
Electrical Shock Hazard.
Plug into a grounded 3-prong outlet.
Do not remove the ground prong.
Do not use an adapter.
Immediately replace electric cords that become frayed
or damaged.
Do not use an extension cord with this appliance.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Follow the instructions in the section Grounding the
Refrigerator.
This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and the word “DANGER”, “WARNING”, or “CAUTION”. These
words are defined as:
DANGER
Indicates a hazardous situation which, if not avoided, will result in death or serious injury.
WARNING
Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION
Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
For Monogram local service in your area, call 1.800.444.1845.
For Monogram service in Canada, call 1.800.561.3344
For Monogram Parts and Accessories, call 1.800.626.2002.
www.monogram.com
WARNING
Tip Over Hazard.
These refrigerators are top heavy, especially with any doors open, and must be secured to prevent tipping
forward which could result in death or serious injury. Read and follow the entire installation instructions for
securing the refrigerator with the anti-tip system.
WARNING
Explosion Hazard.
Keep flammable materials and vapors, such as gasoline, away from refrigerator. Failure to do so can result in
fire, explosion, or death.
WARNING
To reduce the risk associated with choking, do not allow children under 3 years of age to have
access to small parts during the installation of this product.
CAUTION
Lifting Hazard
This refrigerator is very heavy. To reduce the risk of person injury during maneuvering and installing this
refrigerator, 3 people are required for proper installation of 36” wide model and 4 people are required for proper
installation of a 42” or 48” wide model.
AVERTISSEMENT
Risque de basculement
Ces réfrigérateurs présentent une partie supérieure lourde, en particulier avec une porte ouverte; ils doivent donc
être fixés pour prévenir le basculement vers l’avant et le risque concomitant de blessure grave ou fatale. Lisez et
suivez les instructions d’installation complètes pour l’installation du système anti-basculement.
AVERTISSEMENT
Risque d’explosion.
Conservez les matériaux et vapeurs inflammables tels que l’essence à l’écart de votre réfrigérateur. Le non-
respect de cette instruction peut entraîner un risque d’incendie, d’explosion ou de décès.
AVERTISSEMENT
Pour réduire le risque d’étouffement pendant l’installation de ce produit, ne pas laisser les
petites pièces à la portée des enfants âgés de moins de 3 ans.
ATTENTION
Risque associé à la manutention d’une charge lourde
Ce réfrigérateur est très lourd. Pour réduire le risque de blessure lors de la manutention de ce réfrigérateur, trois
(3) personnes sont nécessaires pour procéder à l’installation appropriée du modèle 36 pouces, quatre (4) pour
l’installation des modèles 42 ou 48 pouces.
Consignes de Sécurité
3
AVERTISSEMENT
Risque de choc électrique.
Branchez l’appareil dans une prise triple avec terre.
Ne retirez pas la broche de terre.
N’utilisez pas d’adaptateur.
Le non-respect de ces instructions peut entraîner des
risques d’incendies, des chocs électriques ou la mort.
Remplacer immédiatement tout cordon électrique
effiloché ou endommagé.
N’utilisez pas de rallonge avec cet appareil.
Le non-respect de ces instructions peut entraîner des
risques d’incendies, des chocs électriques ou la mort.
Suivez les instructions de la section Mise à la terre du
réfrigérateur.
Ce symbole représente une alerte de sécurité. Ce symbole vous avise de dangers possibles pouvant causer la mort, des
blessures ou autres. Tous les messages de sécurité seront précédés du symbole d’alerte de sécurité ainsi que des mots «
DANGER », « AVERTISSEMENT » ou « MISE EN GARDE ». Ces messages sont les suivants :
Signale une situation qui présente un danger imminent et qui, si elle n’est pas évitée, entraînera des bles
sures graves, voire la mort.
Signale une situation qui présente un danger imminent et qui, si elle n’est pas évitée, peut entraîner des
blessures graves, voire la mort. .
Signale une situation qui présente un danger imminent et qui, si elle n’est pas évitée, peut entraîner des
blessures mineures ou graves.
AVERTISSEMENT
DANGER
ATTENTION
4
Contents
Safety 2, 3
Planning Guide
The Installation Space 5
Dimensions and Clearances 5
90° Door Swing 10
130° Door Swing 11
Customization Basics 6
3/4” Overlay Panel Dimensions - Flush 7
1/4” Framed Panel Dimensions - Standard 8
3/4” Overlay Panel Dimensions - Standard 9
Dispenser Trim 12
Side Panels 13
Installation Instructions
Tools, Hardware, Materials 13
Parts Identification 14
Grounding the Refrigerator 15
Step 1. Remove Packaging 16
Step 2. Move Refrigerator into House 16
Step 3. Install Water Line 16
Step 4. Household Water Filtration 17
Step 5. Install Side Panels 17
Step 6. Install Case Trim 17
Step 7. Anti-Tip Procedure 17-18
Step 8. Level Refrigerator 18
Step 9. Secure Refrigerator to Cabinetry 18
Step 10. Adjust Door Swing 19
Step 11. Remove Door Trim 19
Step 12. Layout Decorative Door Panels 20-21
Step 13. Attach Brackets to Panels 21
Step 14. Hang Decorative Door Panels 22
Step 15. Layout Decorative Hood Panel 23
Step 16. Install Hood Panel 23
Step 17. Adjust Decorative Panels 24-25
Step 18 Replace Trim 25
Step 19. Connect Water Supply 26
Step 20. Connect Power, Close Grille Panel 26
Step 21. Start Icemaker 26
Step 22. Install Toekick 27
Inspect Final Installation 27
B
A
Design Guide
THE INSTALLATION SPACE
Water And Electrical Locations
The opening must be prepared with the electrical
and the cold water supply located as shown.
The cutout depth must be 24”
The refrigerator will project forward, slightly beyond
adjacent cabinetry, depending on your installation.
Additional Specifications
• A 115 volt 60Hz., 15 or 20 amp power supply is
required. An individual properly grounded branch
circuit or circuit breaker is recommended. Install
a properly grounded 3-prong electrical receptacle
recessed into the back wall. Electrical must be located
on the rear wall as shown.
NOTE: GFI (ground fault interrupter) is not
recommended.
• The water line can enter the opening through the
floor or back wall. The water line should be 1/4” O.D.
copper tubing or GE SmartConnect
™
kit between the
cold water line and water connection location, long
enough to extend to the front of the refrigerator.
Installation of an easily accessible shut-off valve in
the water line is required.
DIMENSIONS AND CLEARANCES
* Shipping height.
The refrigerator can
be adjusted to fit
into a cutout that
is 84-1/2” in height.
Use leveling legs
and wheels for a
maximum 1” height
adjustment.
Product Clearances
These refrigerators are
equipped with a 3-position
door stop. The factory-set
115° door swing can be
adjusted to 90° if clearance
to adjacent cabinets or
walls is restricted. Only
standard installation can be
adjusted to 130°.
5
*For standard installation, the finished cutout width
must be:
35-1/2” for 36” models
41-1/2” for 42” models
47-1/2” for 48” models
*For flush mount installation, the finished cutout width
must be:
39” for 36” models
45” for 42” models
522” for 48” models
90° Door Swing
130° Door Swing
115° Door Swing
*Finished Width
6"
5"
Electrical
Area
84 1/2" max
Finished
Opening
75" From Floor
to Bottom
of Electrical
Area
24"
5"
5"
3 1/2"
Water Supply
3 1/2"
36" Models 12"
42" Models 18"
48" Models 20"
Allow minimum clearances for the freezer door
(Dimension A) and fresh food door (Dimension B) for a
full 130° door swing and to allow for pan removal.
For a 90° door swing, allow 4” min. clearance to a wall,
for framed and stainless steel models. Allow 5” min.
clearance for professional series models. If the 90° door
stop position is used, pan access is maintained, but pan
removal is restricted.
See the illustrations on pages 6 and 7 to determine door
swing interaction with adjacent cabinets or countertops.
Models A B C
36” 13” 15” 20-5/8”
42” 13” 19” 26-5/8”
48” 15” 20” 28-5/8”
*84"
From
Floor
25-3/8" Framed Models
25-3/4" Stainless Steel Models
Depth Including Handles:
27-3/4" Stainless Steel Models
28-11/16" Professional Models
36", 42" or 48"
Frame to Frame
35", 41", or 47"
Case Width
*83-1/2"
at
Rear
23-7/8"
Behind
Frame
C
*Min. Distance
to Wall
*4” Stainless and
Trimmed Models.
5” Pro Series
B
A
CUSTOMIZATION BASICS:
Professional Style Stainless Steel Refrigerators
Stainless steel wrapped refrigerators have beveled edges and professional-style handles. These models are shipped ready
for installation.
Stainless Steel Wrapped Refrigerators
Stainless Steel wrapped refrigerators have wrapped doors and grille panel, beveled edges, and tubular stainless steel
handles that coordinate with other Monogram appliances. These models are shipped ready for installation.
Trimmed Refrigerators
Trimmed refrigerators are designed to be customized with decorative panels. Field installed custom door and grille panels
are required.
6
Optional Accessory Kits
ZKHSS2: Monogram Tubular Stainless Steel handles
designed to fit 3/4” overlay panels.
ZKHPSS1: Professional Tubular Stainless Steel handles
designed to fit 3/4” overlay panels. Kit includes one
handle. Order 2 kits for side-by-side refrigerator models
from your Monogram supplier
ZTK36SSH: Trim Kit for 36” Side-by-side refrigerator using
custom panels for standard installation.
ZTK42SSH: Trim kit for 42” Side-by-side refrigerator using
custom panels for standard installation.
ZTK48SSH: Trim kit for 48” Side-by-side refrigerator using
custom panels for standard installation.
Design Guide
7
Design Guide
3/4” OVERLAY PANEL DIMENSIONS
(Flush Installation Only)
For a more custom appearance, overlay panels may be
installed to give a flush appearance with surrounding
cabinets. The overlay panel must be 3/4” thick. Panel
attaches to included brackets to provide mounting to the
appliance door.
IMPORTANT NOTE – DISPENSER MODELS
The refrigerator is supplied with matching adjustable
dispenser trims. The overlay dispenser trim is designed to fit
a total panel thickness of 3/4” plus up to 1/8” adjustability.
• If the panel is less than 3/4” a noticeable gap may be
created around the dispenser trim.
• If the panel is more than 3/4” and fully adjusted away
from door face, the dispenser trim cannot be secured to
the door.
Fresh
Food
Panel
Freezer
Panel
E
D
F
G
A
B
Grille Panel
C
Dispenser
Cutout
9-5/8"
Dispenser Cutout
15-3/8
"
IMPORTANT NOTE: Maximum total weight for the assembled
panels:
• Fresh food door panel – 75 lbs.
• Freezer door panel – 53 lbs.
• Grille Panel – 18 lbs.
Refrigerator A B C D E F G
36” Side-by-Side
(in inches)
38” 10-5/8” 68-13/16” 16-7/8” 20-7/8” 18” 3-7/16”
42” Side-by-Side
(in inches)
44” 10-5/8” 68-13/16” 16-7/8” 26-7/8” 18” 3-7/16”
48” Side-by-Side
(in inches)
50” 10-5/8” 68-13/16” 20-7/8” 28-7/8” 18” 5-7/16”
Dispenser
Cutout
Position
1/2”
1/2”
1-1/4”
1”
1-1/4”
1”
Top/Bottom Hinge Clearance
Router 1/8” Deep
CUSTOM HANDLE DESIGN GUIDE
(Flush Installation Only)
For custom handle installation, counterbore holes in rear
of decorative panels may not exceed 1/4” depth to ensure
1/2” material thickness remains for handle support.
NOTE: The counterbore must not exceed 1” in diameter.
Minimum distance from handle
side edge to handle center
should be 1-1/4” as shown.
1/4”
1/2”
3/4”
1-1/4”1-1/4”
Improper installation can lead to a finger pinch
point hazard between the side door trim and the
cabinets when operating the door, especially
with children. To minimize this risk you must
follow the installation instructions for cabinet
dimensions, trim assembly, and door stop angle.
Door Trim Pinch Point Hazard
WARNING
1/4” FRAMED PANEL DIMENSIONS
(Standard Installation Only)
8
If you choose to install framed panels, they must
be cut to the dimensions shown. The panels will slide
into the frame on the door and grille.
Non-Dispenser Models
If the custom panel is less than 1/4” thick and it fits
loosely in the door frame it can be backed up with
a piece of filler material or foam tape to improve
the fit.
Fresh
Food
Panel
Freezer
Panel
E
D
F
G
A
B
Grille Panel
C
Dispenser
Cutout
9-5/8"
Dispenser Cutout
15-3/8
"
Side-by-Side (in inches)
A B C D E F G
36” Models 33-7/8 9 68-3/8 14-9/16 18-9/16 17-13/16 3-1/8
42” Models 39-7/8 9-1/2 68-3/8 14-9/16 24-9/16 17-13/16 3-1/8
48” Models 45-7/8 9-1/2 68-3/8 18-9/16 26-9/16 17-13/16 5-1/8
Dispenser
Cutout Position
IMPORTANT NOTE: Maximum total panel weight:
• Fresh food door panel – 75 lbs.
• Freezer door panel – 53 lbs.
• Grille Panel – 18 lbs.
1/4"
Panel
Door
5/16"
Trim
Reveal
The framed panel must be 1/4” nominal
thickness to fit the dispenser trim.
IMPORTANT NOTE – DISPENSER MODELS
The refrigerator is supplied with two dispenser trims,
one for framed panels and one for overlay panels.
• If the panel is less than 0.250” thick, a noticeable gap
may be created around the dispenser trim. Foam
tape may be applied on the door to improve the fit.
• If the panel is more than 0.250” thick, the dispenser
trim cannot be secured to the door.
See Dispenser Trim Fit Example, page 12.
Design Guide
3/4” OVERLAY PANEL DIMENSIONS
(Standard Installation Only)
For a more custom appearance, overlay panels may
be installed on trimmed models. The overlay panel must
be secured to a 1/4” thick backer panel which slides
into the trim. A spacer panel 0.10” thick must be placed
between the overlay and backer panel.
Assemble the panels with glue and screws:
• Center the spacer panel on the backer panel, left to
right and top to bottom. Secure the panels with glue.
• Center the spacer and backer panel on the overlay
panel and secure with glue and screws. Screws must
be countersunk into the backer panel.
NOTE: Left-to-right offset is
not always equal to top-to-
bottom offset.
9
Spacer Panel
Overlay Panel
Backer Panel
Fresh
Food
Panel
Freezer
Panel
E
D
F
G
A
B
Grille Panel
C
Dispenser
Cutout
9-5/8"
Dispenser Cutout
15-3/8
"
*Cut the dispenser opening after the backer, spacer and overlay
panels have been assembled.
36” Side-by-Side (in inches)
A B C D E F G
1/4” Backer Panel 33-7/8 9 68-3/8 14-9/16 18-9/16
.10” Spacer Panel 33 8-3/8 67 13-1/4 17-1/4
3/4” Overlay Panel 34-1/8 9-1/4 68-5/8 14-13/16 18-13/16 17-15/16 3-1/4
42” Side-by-Side (in inches)
A B C D E F G
1/4” Backer Panel 39-7/8 9-1/2 68-3/8 14-9/16 24-9/16
.10” Spacer Panel 39 8-5/8 67 13-1/4 23-1/4
3/4” Overlay Panel 40-1/8 9-3/4 68-5/8 14-13/16 24-13/16 17-15/16 3-1/4
48” Side-by-Side (in inches)
A B C D E F G
1/4” Backer Panel 45-7/8 9-1/2 68-3/8 18-9/16 26-9/16
.10” Spacer Panel 45 8-5/8 67 17-1/4 25-1/4
3/4” Overlay Panel 46-1/8 9-3/4 68-5/8 18-13/16 26-13/16 17-15/16 5-1/4
*Dispenser
Cutout Position
IMPORTANT NOTE: Maximum total weight for the assembled
panels:
• Fresh food door panel – 75 lbs.
• Freezer door panel – 53 lbs.
• Grille Panel – 18 lbs.
IMPORTANT NOTE – DISPENSER MODELS
The refrigerator is supplied with two dispenser trims,
one for framed panels and one for overlay panels. The
overlay dispenser trim is designed to fit a total panel
thickness of 1.100”.
• If the panel is less than 1.100” a noticeable gap may
be created around the dispenser trim.
• If the panel is more than 1.100” the dispenser trim
cannot be secured to the door.
See Dispenser Trim Fit Example, page 12.
.250” + .10” + .750” = 1.100” Total Panel Thickness
• The overlay panel must be constructed according to
the specifications shown to achieve the correct total
thickness.
• Alternative panel construction methods such as
securing a 3/4” panel to a 1/4” backer panel cannot
be used. Another method, routing a 3/4” thick panel
on all sides, cannot be used. These methods will not
result in the required 1.100” panel thickness.
3/4"
Overlay
Panel
1/4"
Backer
Panel
Door
.10"
Spacer
Design Guide
1/4"
1/2"
3/4"
1"
1-1/4"
1/4"
1/2"
3/4"
1"
1-1/4"
1-1/2"
23-7/8"
From Rear of
Refrigerator
3/4" Overlay
Panel
(Nominal Size)
Case Trim
Refrigerator
Door
Stainless Steel
10
Top View
90° DOOR SWING
(Standard Installation
Only)
Scale 1:1
IMPORTANT NOTE –
FOR DISPENSER MODELS:
Dispenser models are supplied
with two dispenser trims, one to fit
framed panels and one for overlay
panels. Dispenser trim fit to the
custom panel depends on correct
panel thickness. Framed panels
must be 1/4” nominal. Overlay
panels should be constructed as
shown to accomplish a total 1.100”
thickness
. See pages 9 and 10 for
details.
Frameless Cabinets:
The case trim overlaps
cabinets at the top
and sides. Therefore,
frameless cabinets may
require filler strips to
prevent interference
with cabinet door swing.
The opening must allow
for filler strips.
Design Guide
Design Guide
11
1/4"
1/2"
3/4"
1"
1-1/4"
1"
3/4" Overlay
Panel
(Nominal Size)
Stainless Steel
1/4"
1/2"
3/4"
2"
1-1/4"
1-1/2"
1-3/4"
3"
2-1/4"
2-1/2"
2-3/4"
1/4"
1/2"
3/4"
Door
23-7/8" From
Rear of
Refrigerator
1"
Refrigerator
Case
Trim
Top View
130° DOOR SWING
(Standard Installation Only)
Scale 1:1
IMPORTANT NOTE –
FOR DISPENSER MODELS:
Dispenser models are supplied with two
dispenser trims, one to fit framed panels
and one for overlay panels. Dispenser trim
fit to the custom panel depends on correct
panel thickness. Framed panels must be
1/4” nominal. Overlay panels should be
constructed as shown to accomplish a total
1.100” thickness. See pages 9 and 10 for
details.
Frameless Cabinets: The case trim overlaps
cabinets at the top and sides. Therefore,
frameless cabinets may require filler strips
to prevent interfeence with cabinet door
swing. The opening must allow for filler strips.
12
DISPENSER TRIM FIT EXAMPLES:
(NOT TO SCALE)
3/4” OVERLAY PANEL
(Flush Installation Only)
• The dispenser trim fits over the
custom panel and snaps into the
freezer door.
1/4” FRAMED PANEL
(Standard Installation
Only)
• The dispenser trim fits over the
custom panel and snaps into the
freezer door.
• The clips will not engage the door
if the panel is more than 0.250” thick.
• If the panel is less than 0.250” thick,
a noticeable gap may be created
around the dispenser trim.
3/4” OVERLAY PANEL
(Standard Installation
Only)
• The dispenser trim fits over the
custom panel and snaps into the
freezer door.
• The clips will not engage the door
if the panel is more than 1.100” thick.
• If the panel is less than 1.100” thick,
a noticeable gap may be created
around the dispenser trim.
Design Guide
13
SIDE PANELS
Side panels must be used
whenever the sides of the
refrigerator will be exposed.
The 1/4” side panels will
slip into the side case trim.
Secure the panels to the
refrigerator with stick-on
hook and loop fastener
strips. Order the side
panels from the cabinet
manufacturer.
• Cut a notch in the top
front corner as shown
to allow clearance for
corner keys in the front
side trim.
* Depending on installation height.
TOOLS AND MATERIALS REQUIRED
• Tinsnips to cut banding
• Stepladder
• 1” Bit extension
• Tape measure
• Gloves
• 1/4” Drywall screws
• 5-Gal. Bucket with cover
• 6” Spirit level
• Appliance hand truck
• Tubing cutter
• 7/16” open-end wrench
• #2 Phillips screwdriver
• Drill and appropriate bits
• 5/16”, 7/16” socket
• Safety glasses
• 1-1/8” open end wrench
• Pliers
• 1/4”, 5/16” Combo Rachet
• 35” long 2x4 for Anti-Tip support
• 1/4” copper water line tubing or GE SmartConnect
™
Refrigerator Tubing kits
• Water shut-off valve
• Custom panels for doors and grille panel
• Screws to secure refrigerator to cabinetry
• Stick-on hook and loop fastener strips for
1/4” side panels
*84"
2-9/16"
24"
*3" to 4"
3/16"
1-7/8"
Installation Instruction
HARDWARE SUPPLIED
• Water filter bypass plug
• Toekick
• 1/4” nut and ferrule
• Dispenser trim for overlay panels (for use with
Custom Panel models).
• Flush inset panel bracket kit
• Case trim package
PARTS IDENTIFICATION:
14
Installation Instruction
Trim, Freezer
Bottom
Trim, Handle
Side Visor,
Fresh Food
Trim, Handle
Side Visor,
Freezer
Trim, Freezer
Handle Side
Cover
Trim, Fresh
Food Top
Trim, Fresh
Food Bottom
Trim, Freezer
Hinge Side
Panel Bracket,
Top Right
Panel Bracket,
Bottom Left
Panel Bracket,
Bottom Right
Panel Bracket,
Top Left
Panel Bracket,
Top (2)
Panel Bracket,
Bottom (2)
Door Bracket
(4);
Installed on
door
Drill holes at top of freezer panel.
Drill holes at bottom of freezer panel.
Fresh Food
Panel Template
Drill holes at top of fresh food panel.
Drill holes at bottom of fresh food panel.
Freezer Panel
Template
Hood Template
Trim, Freezer
Top
Trim, Fresh
Food Handle
Side Cover
Trim, Fresh
Food Hinge
Side
Trim, Case,
RH Side
Trim, Case,
LH Side
GROUNDING THE REFRIGERATOR
WARNING
Electrical Shock Hazard.
Failure to follow these instructions can result in death,
fire, or electrical shock.
The power cord of this appliance is equipped
with a 3-prong (grounding) plug which mates
with a standard 3-prong (grounding) wall receptacle
to minimize the possibility of electric shock hazard
from this appliance.
Have the wall outlet and circuit checked by
a qualified electrician to make sure the outlet
is properly grounded.
Where a standard 2-prong wall outlet is encountered,
it is your personal responsibility and obligation
to have it replaced with a properly grounded
3-prong wall outlet.
DO NOT, UNDER
ANY CIRCUMSTANCES,
CUT OR REMOVE
THE THIRD (GROUND) PRONG
FROM THE POWER CORD.
DO NOT USE AN ADAPTER PLUG TO CONNECT
THE REFRIGERATOR TO A 2-PRONG OUTLET.
DO NOT USE AN EXTENSION CORD WITH THIS
APPLIANCE.
MISE À LA TERRE DU RÉFRIGÉRATEUR
AVERTISSEMENT
Risque de choc électrique.
Le non-respect de ces instructions peut entraîner des
risques d’incendies, des chocs électriques ou la mort.
Le cordon d’alimentation de cet appareil est équipé
d’une fiche à trois broches (pour une mise à la terre)
qui s’adapte à la prise de courant standard à 3
broches (pour une mise à la terre) pour minimiser les
risques de chocs électriques par cet appareil.
Faites vérifier la prise murale et le circuit électrique par
un électricien qualifié pour s’assurer que le système est
correctement mis à la terre.
Dans le cas d’une prise biphasée, l’installateur a la
responsabilité et l’obligation de la remplacer par une
prise triphasée correctement mise à la terre.
NE COUPEZ PAS OU N’ENLEVEZ
PAS, SOUS AUCUN PRÉTEXTE,
LA TROISIÈME BROCHE DE
MISE À LA TERRE DU CORDON
D’ALIMENTATION.
N’UTILISEZ PAS D’ADAPTATEUR
POUR BRANCHER LE
RÉFRIGÉRATEUR À UNE PRISE BIPHASÉE.
N’UTILISEZ PAS DE RALLONGE AVEC CET APPAREIL.
FLOORING
For proper installation, this refrigerator must be placed
on a level surface of hard material that is at the same
height as the rest of the flooring. This surface should
be strong enough to support a fully loaded refrigerator,
or approximately 1,500 lbs.
NOTE: Protect the finish of the flooring. Cut a large
section of the cardboard carton and place under
the refrigerator where you are working.
REFRIGERATOR LOCATION
• Do not install the refrigerator where the
temperature will go below 55°F (13°C). It will not run
often enough to maintain proper temperatures.
• Do not install the refrigerator where temperatures
will go above 100°F (37°C). It will not perform
properly.
• Do not install the refrigerator in a location exposed
to water (rain, etc.) or direct sunlight.
15
Installation Instruction
Installation Instructions
STEP 1 REMOVE PACKAGING
WARNING
Tip Over Hazard.
The refrigerator is much heavier at the top than at the
ERWWRP³EHFDUHIXOZKHQPRYLQJ:KHQXVLQJDKDQG
truck, handle from the side only.
AVERTISSEMENT
Risque de basculement
Le réfrigérateur est beaucoup plus lourd en haut qu’en
bas. Il faut être prudent lors des déplacements. Si un
diable est utilisé, il faut soulever le réfrigérateur sur le
côté seulement.
• Carefully cut banding at the top and bottom, remove
the outer carton.
• Slide out the back corner posts (2).
• Slide the carton off the top of the cabinet.
NOTE: IT IS NOT NECESSARY TO LAY THE CABINET DOWN
IN ORDER TO REMOVE THE SKID!
• The unit is secured to the
skid with 4 slotted tie-
down straps. Remove the
six 7/16” bolts from the
base channels in the tie-
downs.
• Remove the six 7/16” bolts
securing the straps to the
skid.
NOTE: DO NOT ATTEMPT TO
ROLL UNIT OFF SKID.
• The support blocks on the
bottom of the refrigeration
case must be removed before the refrigerator is taken
off the skid or damage will occur. Carefully tilt the
refrigerator and slide the blocks out from beneath.
• Remove the toekick and set aside for final installation.
• Lift the refrigerator off the skid with an appliance dolly.
Handle from the sides.
STEP 3 INSTALL WATER LINE
• A cold water supply is required for automatic icemaker
operation. The water pressure must be between 40 and
120 p.s.i.
• Route 1/4” OD copper or GE SmartConnect
™
plastic
tubing between house cold water line and the water
connection location.
• The tubing should be long enough to extend to the
front of the refrigerator. Allow enough tubing to
accommodate the bend leading into the water line
connection.
16
Remove
Tie Downs
Toekick
Templates
Floor
Cold Water Line
NOTE: The only GE approved plastic tubing is supplied
in the GE SmartConnect
™
Refrigerator Tubing kits. Do
not use any other plastic water supply line because
the line is under pressure at all times. Other types of
plastic may crack or rupture with age and cause water
damage to your home.
GE SmartConnect
™
Refrigerator Tubing Kits are
available in the following lengths:
2’ (.6 m) WX08X10002
6’ (1.8 m) WX08X10006
15’ (4.6 m) WX08X10015
25’ (7.6 m) WX08X10025
STEP 2 MOVE THE REFRIGERATOR
INTO THE HOUSE
• Re-use the corner posts from the packaging to protect
stainless steel models. Run the appliance dolly straps
over the posts and under the handles.
• Leave the protective film on the refrigerator until
installation is complete.IMPORTANT: Never lift the
refrigerator by the handle or push against the grill
panel; this could cause damage or misalignment.
• Avoid laying the unit on its back or side to prevent
sealed system restrictions.
NOTE: Commonwealth of Massachusetts Plumbing
Codes 248CMR shall be adhered to. Saddle valves
are illegal and use is not permitted in Massachusetts.
Consult with your licensed plumber.
Shut off the main water supply.
Turn on the nearest faucet long enough to clear the line
of water.
• Install a shut-off valve between the icemaker water
valve and cold water pipe in a basement or cabinet.
The shut-off valve should be located where it will be
easily accessible.
• Turn on the main water supply and flush debris.
Run about a quart of water through the tubing into a
bucket. Shut off the water supply at the shut-off valve.
NOTE: Saddle type shut-off valves are included in many
water supply kits. Before purchasing, make sure a saddle
type valve complies with your local plumbing codes.
17
STEP 4 INSTALLATION WITH
HOUSEHOLD WATER
FILTRATION SYSTEM
Skip this step if you do not have a household water
filtration system
If the water supply to the refrigerator is from any
household water filtration system, the filter cartridge
should be removed. For better ice and water
performance, remove the filter and install the filter bypass
plug.
STEP 5 INSTALL SIDE PANELS
Skip this step when not using side panels.
If you are using 1/4” side panels, they should be
inserted into the case trim. Fasten the panels to the
refrigerator with stick-on hook and loop fastener strips
before setting the refrigerator in place.
STEP 6 INSTALL CASE TRIM
Install case trim using supplied right hand and left hand
case trim pieces and case trim screws. Attach case trim
to each side of case as shown in illustration using case
trim screws in holes provided down each side of case.
STEP 7
ANIT-TIP PROCEDURE
WARNING
Tip Over Hazard.
These refrigerators are top heavy, especially
with any doors open, and must be secured to
prevent tipping forward which could result in
death or serious injury. Read and follow the
entire installation instructions for securing the
refrigerator with the anti-tip system.
AVERTISSEMENT
Risque de
basculement
Ces réfrigérateurs présentent une partie
supérieure lourde, en particulier avec une porte
ouverte; ils doivent donc être fixés pour prévenir le
basculement vers l’avant et le risque concomitant
de blessure grave ou fatale. Lisez et suivez
les instructions d’installation complètes pour
l’installation du système anti-basculement.
Flush Installation Only
• Cut a 1/2” x 4” block, 35” long.
• Measure and mark under the soffit, 5-1/4” from the
front edge of the cabinet.
• Secure the wood block to under the soffit. From
the bottom of the block to the finished floor should
measure 84”. See the illustration.
Installation Instructions
Filter Bypass
Plug
Rotate Counterclockwise To
Remove
Standard Installation Only
• Cut a 2” x 4” block, 35” long and secure the block to
the mounting brackets provided using #12 or #14
wood screws.
• Secure the bracket with wood block to the back wall
so that it is 84” from the finished floor. Use #12 or #14
wood screws. See the illustration.
• The screws must penetrate at least one inch into the
vertical wall studs.
IMPORTANT NOTE FOR STANDARD INSTALLATION:
When the refrigerator is installed under a soffit or if
there is not enough height for this method of security,
brackets cannot be used. Proceed to step 8 to level the
refrigerator and then to step 9 to secure refrigerator to
cabinets. See step 8 if you have metal wall studs. The
refrigerator must be secured to prevent tipping.
Connect power cord:
• Before pushing the refrigerator into the opening, plug
the power cord into the receptacle. Open the grille
panel and reach into the opening at the back to grasp
the power cord. Pull the power cord into the opening
as you push the refrigerator back.
• Gently push refrigerator into the opening with hands
against front corners.
STEP 7
ANTI-TIP PROCEDURE (Cont.)
18
STEP 8 LEVEL REFRIGERATOR
All models have 4-point leveling. The front is supported
by leveling legs, the rear is supported by adjustable
wheels. Both are accessible from the front of the
refrigerator.
• To level the back of the refrigerator, turn the 7/16”
hex nut located above
the front wheels. Turn
clockwise to raise or
counterclockwise to lower
the refrigerator.
• For front leveling, use a
1-1/4” open-end wrench.
• Adjust height of
refrigerator to match
installation cutout opening
84-1/2”. The refrigerator should be level and plumb
with
cabinetry
.
NOTE (Flush Installation Only): Raise refrigerator until
the case top comes in contact with the 1/2” spacer
block mounted to the underside of the cabinet soffit.
Refrigerator should be level at fully raised position.
NOTICE: The rear leveling wheels and front leveling
legs are limited to a maximum height adjustment of 1”.
If the installation requires more than 84-1/2” height,
the installer should elevate the refrigerator on a sheet
of plywood or runners. Cabinetry trim could also be
added across the top of the opening to shorten the
opening. If you attempt to raise the refrigerator more
than 1”, you will damage the front leveling legs and
the rear leveling wheels. Make adjustments in small
increments.
Installation Instructions
STEP 9 SECURE REFRIGERATOR
TO CABINETRY
Whenever possible, perform this step for anti-tip
security, or when anti-tip brackets cannot be used.
The refrigerator must be secured to prevent tipping.
• Raise the grille panel to access the machine
compartment.
• For flush inset installation only, drill a hole in the case
top and drive a screw through the top into the adjacent
1/2” block.
STEP 11 REMOVE DOOR TRIM - FLUSH INSTALLATION ONLY
Use the supplied Torx wrench or T10 Torx head driver to
remove all exposed trim screws securing aluminum trim
to refrigerator doors. Save all trim and screws as they
will be replaced in a later step.
1. Remove screws from door hinge side of both left and
right doors. Once screws are removed, remove trim
from hinge side of each door.
2. Remove 4 trim screws on vertical handle side on each
door to release handle cover trim. Remove the handle
cover trim from the handle side of each door to expose
handle visor trim underneath.
3 Remove 4 additional trim screws from handle visor
trim on each door. Once screws have been removed,
remove handle visor trim from each door.
19
Installation Instructions
STEP 10 ADJUST DOOR SWING
NOTE: This refrigerator has a 3-position door stop.
When space does not allow the door to swing open
fully to 115°, you may change the door swing to a
90° opening. A 130° door swing option is available
for standard installation only. Skip this step if door
opening is satisfactory for your installation situation.
• Open the door to view the bottom hinge.
Note the door stop pin locations. The pin is factory
installed in the 130° position.
• Close the door. From below, use pliers to unscrew
the door stop and reinstall into the 90° position.
Hinge side
trim
Hinge side
trim
Handle
visor trim
Handle
side trim
20
Installation Instructions
STEP 12 LAYOUT DECORATIVE DOOR PANELS - FLUSH INSTALLATION ONLY
Decorative wood panels must be cut to a thickness of
3/4”. The dimensions of each panel can be determined by
referring to the specs provided with refrigerator. Panels
must be predrilled to prevent accidental splitting or
cracking of wood when attaching to door brackets in the
next step.
1. Cut Freezer (left) side and Fresh food (right) side panels
to specified dimensions (as noted on page 11 under
Design Guide).
2. Lay the Freezer and Fresh Food panels face down on a
non-scratch surface.
3. Mark a vertical centerline on the backside of the Freezer
and Fresh Food panels.
4. Lay supplied Fresh Food panel TEMPLATE (attached
to side case of refrigerator) on the back of the Fresh
Food panel with the lettering face up. See illustration
to ensure proper template has been selected. Align the
top, side, and centerline of the template with the top,
side and centerline of the door. Tape the template to
the panel using masking tape to temporarily secure it in
place.
5. Repeat previous step on the Freezer door panel using
the Freezer panel Template.
6. Using a 1/8” wood drill bit, drill pilot holes into the door
panels 1/4” deep through only the top group of holes
in the templates. Four holes will be drilled into the upper
corners of each door panel.
7. Using a pencil, trace the outline of the notch out of the
template at the top corner of each door. This mark will
provide a guide for routing wood to provide relief for
door hinge at top of door panel.
8. Remove the tape from each panel. Slide the templates
to the bottom of each panel aligning the bottom, sides,
and centerline of the panel with the bottom, sides and
centerline of the templates. Tape in place.
9. Using a 1/8” wood drill bit, drill pilot holes into the door
panels 1/4” deep through only the bottom group of
holes in the templates. Four holes will be drilled into the
bottom corners of each door.
Panel is face down
on a non-scratch
surface. You will be
drilling on the BACK
of the panel.
Panel is face down on a non-
scratch surface. You will be drilling
on the BACK of the panel.
Template is
aligned with
top of FZ panel.
Template is
aligned with
top of FF panel.
Move the
templates from
the tops to the
bottoms on the
back side of the
door panels.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

Monogram ZISS480NHSS Guide d'installation

Monogram
Marque
Monogram
Modèle
ZISS480NHSS
Catégorie
Frigos
Taper
Guide d'installation
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents