Shindaiwa BP520S Manuel utilisateur

Marque: Shindaiwa

Modèle: BP520S

Catégorie: Coupe-herbe

Taper: Manuel utilisateur

1????

OPERATOR'S MANUAL

MANUEL D'UTILISATION

BEDIENUNGSANLEITUNG

MANUALE PER L'OPERATORE

BP520S

ENGLISH

FRANÇAIS

DEUTSCH

ITALIANO

WARNING

READ THE INSTRUCTIONS CAREFULLY AND FOLLOW THE RULES FOR

SAFE OPERATION.

FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY.

AVERTISSEMENT

LIRE ATTENTIVEMENT LES INSTRUCTIONS ET SUIVRE LES RE-GLES DE

SECURITE. LE NON-RESPECT DES REGLES DE SECU-RITE ENTRAINE UN

RISQUE DE BLESSURE GRAVE.

WARNUNG

LESEN SIE DIE BEDIENUNGSANLEITUNG SORGFÄLTIG DURCH, UND BE-

FOLGEN SIE DIE SICHERHEITSREGELN. ANDERNFALLS BESTEHT DAS

RISIKO SCHWERER VERLETZUNGEN.

AVVERTENZA

LEGGERE E SEGUIRE ATTENTAMENTE LE ISTRUZIONI PER LA-VORARE

IN CONDIZIONI DI MASSIMA SICUREZZA. LA MANCA-TA OSSERVANZA

DELLE ISTRUZIONI POTREBBE PROVOCARE LESIONI GRAVI.

1Cover

ENGLISH

(Original instructions)

OPERATOR'S MANUAL

GRASS-TRIMMER/BRUSHCUTTER

BP520S

WARNING

READ THE INSTRUCTIONS CAREFULLY AND FOLLOW THE

RULES FOR SAFE OPERATION.

FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY.

Important information

2Important information

Please ensure that you read the operator's manual before using your product.



Intended use of this product

 Shindaiwa Grass Trimmers/Brushcutters are lightweight, high-performance, petrol engined units designed for weed

control, grass trimming and brush cutting in areas difficult to control by any other means.

 Do not use this unit for any purpose other than aforementioned.



Users of the product

 You should not use this product until you have read the operator's manual carefully and fully absorbed its content.

 This product should not be used by anyone who has failed to read the operator's manual properly, is suffering from a

cold, tiredness or otherwise in poor physical condition, or children.

 Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people or their prop-

erty.



About your operator's manual

 This manual contains necessary information about the assembly, operation, and maintenance of your product. Please

read it carefully and absorb its contents.

 Always keep your manual in a place where it is readily accessible.

 If you have lost your manual or it is damaged and no longer readable, please purchase a new one from your shindaiwa

dealer.

 The units used in this manual are SI units (International System of Units). Figures in parentheses are reference values,

and there may be a slight conversion error in some cases.



Loaning or assigning your product

 When loaning the product described in this manual to another party, ensure that the person borrowing and working with

the product receives the operator's manual along with the product. If you assign your product to another party, please

enclose the operator's manual with the product when handing it over.



Enquiries

 Please contact your shindaiwa dealer for requests regarding information about your product, the purchase of consum-

ables, repairs, and other such enquiries.



Notices

 The content of this manual may be changed without notice for the purpose of upgrades to the product. Some of the

illustrations used may differ from the product itself in order to make the explanations clearer.

 This product requires the assembly of some parts.

 Please consult your shindaiwa dealer if anything is unclear or of concern.

Manufacturer:

YAMABIKO CORPORATION

7-2 SUEHIROCHO 1-CHOME, OHME, TOKYO 198-8760, JAPAN

Authorized Representative in Europe:

Atlantic Bridge Limited

Atlantic House, PO Box 4800, Earley, Reading RG5 4GB, United Kingdom

Contents

For safe use of your product...............................................................................................4

Warning notices.............................................................................................................4

Other indicators .............................................................................................................4

Symbols.........................................................................................................................4

Location in which a safety decal is attached..................................................................6

Handling fuel..................................................................................................................7

Handling the engine.......................................................................................................8

Handling the product .....................................................................................................9

Packing list........................................................................................................................14

Description........................................................................................................................15

Before you start ................................................................................................................16

Assembly.....................................................................................................................16

Preparing the fuel ........................................................................................................20

Engine operation...............................................................................................................21

Starting the engine ......................................................................................................21

Stopping the engine.....................................................................................................23

Trimming operation...........................................................................................................24

Basic trimming operation with nylon line cutting head.................................................25

Basic trimming operation with metal blade..................................................................26

Precautions to observe when working.........................................................................28

Maintenance and care ......................................................................................................29

Servicing guidelines.....................................................................................................29

Maintenance and care.................................................................................................29

Storage .............................................................................................................................38

Long-term storage (30 days or more)..........................................................................38

Specifications....................................................................................................................39

Declaration of conformity..................................................................................................40

For safe use of your product

Be careful to read this section before using your product.



The precautions described in this section contain important safety information. Please observe them carefully.



You must also read the precautions that appear in the body of the manual itself.

Text following a [diamond mark] mark describes the potential consequences of failing to observe the precaution.

Warning notices

Situations where there is a risk of physical injury to the operator and other people are indicated in this manual and on the product

itself by the following warning notices. Always read and observe them carefully in order to ensure safe operation.

Other indicators

As well as warning notices, this manual uses the following explanatory symbols:

Symbols

In this manual and on the product itself, a series of explanatory symbols is used. Please make sure that you fully understand what

each symbol means.

DANGER WARNING CAUTION

This symbol accompanied by the

word "DANGER" calls attentions to

an act or a condition which will lead to

serious personal injury or death of op-

erators and bystanders.

This symbol accompanied by the

word "WARNING" calls attentions to

an act or a condition which can lead to

serious personal injury or death of op-

erators and bystanders.

"CAUTION" indicates a potentially

hazardous situation which, if not

avoided, may result in minor or mod-

erate injury.

Circle and slash sym-

bol means whatever is

shown is prohibited.

NOTE IMPORTANT

This enclosed message provides tips

for use, care and maintenance of the

product.

Framed text featuring the word "IM-

PORTANT" contains important infor-

mation about the use, checking,

maintenance and storage of the prod-

uct described in this manual.

Symbol form/shape Symbol description/applica-

tion

Symbol form/shape Symbol description/applica-

tion

Carefully read the operator's

manual

The maximum speed of the

cutting attachment shaft in

r/min

Wear eyes, ears and head

protection

Keep bystanders away 15 m

Wear foot protection and

gloves

Petrol and oil mixture

Emergency stop Purge bulb (Primer)

Warning!

Thrown objects!

Carburettor adjustment

- Low speed mixture

For safe use of your product

Warning, side thrust

Carburettor adjustment

- High speed mixture

Usage without shield not per-

mitted

Carburettor adjustment

- Idle speed

Usage of metal blades not

permitted

Lubricate in every 18 hours

Usage of nylon line cutting

head not permitted

Loop handle

Do not use the product in plac-

es with poor ventilation

Beware of high-temperature

areas

Beware of fire

Guaranteed sound power lev-

Choke Control "Cold Start"

Position (Choke Closed)

Choke Control "Run" Position

(Choke Open)

Beware of electric shocks Engine start

Symbol form/shape Symbol description/applica-

tion

Symbol form/shape Symbol description/applica-

tion

For safe use of your product

Location in which a safety decal is attached

 The safety decal shown below has been attached to the products described in this manual. Ensure that you understand what

the decal means before using your product.

 If the decal becomes unreadable due to wear and tear or damage, or peels off and is lost, please purchase a replacement decal

from your dealer and attach it in the location shown in the illustrations below. Ensure that the decal is readable at all times.

1. Safety decal (Part number 890617-43130)

For safe use of your product

Handling fuel

DANGER

Always keep well away from fire when refuelling

Fuel is highly inflammable and leads to a risk of fire if mishandled. Use extreme care when mixing, storing or handling

or serious personal injury may result. Be careful to observe the following instructions.



Do not smoke or hold a flame near when refuelling.



Do not fuel up while the engine is hot or in operation.

 If you do so, the fuel could ignite and cause fire, leading to burns.

About the container and refuelling place



Use an approved fuel container.



Fuel tanks/cans may be under pressure.

Always loosen fuel caps slowly allowing pressure to

equalize.



DO NOT fill fuel tanks indoors.

ALWAYS fill fuel tanks outdoors over bare ground.

Fuel spills can cause fire

Observe the following precautions when refuelling:



Do not add so much fuel that it reaches the mouth of the

fuel tank. Keep the fuel within the prescribed level (up to

the shoulder level of the fuel tank).



Mop up any fuel that overflows or spills out due to over-

filling.



Tighten the fuel tank cap securely after refuelling.

 Fuel spills can cause fire and burns when ignited.

1. Fuel tank

2. Shoulder level

Do not start the engine in the area where you refu-

eled



You must not start the engine in the place where you

carried out the refuelling. Move at least 3m from the

place where you refueled before starting the engine.

 Fuel leaks that occur while refuel-

ling can cause fire if ignited.

Fuel leaks cause fire



After refuelling, always check

that there are no leaks or dis-

charges of fuel from the fuel

pipe, fuel system grommets, or

around the fuel tank cap.



If you do find fuel leaks or discharges, stop using the

product immediately and contact your dealer to have it

repaired.

 Any fuel leaks could cause fire.

For safe use of your product

Handling the engine

WARNING

Starting the engine

Be particularly careful to observe the following precau-

tions when starting the engine:



Check that none of the nuts and bolts are loose



Check that there are no fuel leaks



Place the product in a flat, well ventilated place



Leave plenty of space around the product and do not al-

low people or animals near it



Start the engine with the throttle trigger in the idle speed

position



Hold the product firmly to the ground when starting the

engine

 Failure to observe the precautions could cause an accident

or injury, or even lead to a fatality.

Once the engine has started, check for abnormal vi-

brations and sounds



Check that there are no abnormal vibrations or sounds

once the engine starts. Do not use the product if there

are abnormal vibrations or sounds. Contact your dealer

to have it repaired.

 Accidents involving parts that fall or shatter off can cause

wounds or serious injury.

Do not touch high temperature or high voltage com-

ponents while the product is running

Do not touch the following high temperature or high volt-

age components while the product is running or for some

time after it stops.



Silencer, spark plug, angle transmission,

and other high temperature components

 You could burn yourself if you touch a high

temperature component.



Spark plug, spark plug wire, and other

high voltage components

 You could receive an electric shock if you

touch a high voltage component while the

product is running.

Put safety first in the case of fire or smoke



If fire comes from the engine or smoke appears from

any area other than the exhaust vent, first distance

yourself from the product to ensure your physical safe-

ty.



Use a shovel to throw sand or other such

material on the fire to prevent it from

spreading, or put it out with a fire extin-

guisher.

 A panicked reaction could result in the fire and

other damage becoming more extensive.

Exhaust fumes are toxic



The exhaust fumes from the engine contain toxic gases.

Do not operate the product indoors or in other ill venti-

lated places.

 The exhaust fumes could cause poisoning.

Turn off the engine when checking or maintaining

the product

Observe the following precautions when checking and

maintaining your product after use:



Turn the engine off and do not attempt to check or main-

tain the product until the engine has cooled

 You could burn yourself.



Remove the spark plug cap before performing checks

and maintenance

 An accident could occur if the product starts unexpectedly.

Checking the spark plug

Observe the following precautions when checking the

spark plug.



If the electrodesor terminals are worn, or if there are

cracks in the ceramics, replace them with new parts.



The spark test (for checking whether the spark plug is

sparking) must be carried out by your dealer.



The spark test must not be carried out in proximity of

the spark plug hole.



The spark test must not be performed in places where

there are fuel spills or inflammable gases



You must not touch the

metal parts of the spark

plug

 The spark plug could ig-

nite a fire or give you an

electric shock.

For safe use of your product

Handling the product

General precautions

Precautions for use

WARNING

Operator's manual



Be careful to read the operator's manual

properly before using your product in or-

der to ensure correct operation.

 Failure to do so could lead to an accident or

serious injury.

Do not use the product for anything

other than its intended purpose



You must not use the product for any purpose other

than those described in the operator's manual.

 To do so could lead to an accident or serious injury.

Do not modify the product



You must not modify the product.

 To do so could lead to an accident or serious injury. Any

malfunction resulting from a modification to the product will

not be covered by the manufacturer's warranty.

Do not use the product unless it has been checked

and maintained



You must not use the product unless it has been

checked and maintained. Always ensure that the prod-

uct is checked and maintained on a regular basis.

 Failure to do so could lead to an accident or serious injury.

Loaning or assigning your product



When loaning your product to another party, ensure

that the person borrowing the product receives the op-

erator's manual along with it.



If you assign your product to another party, please en-

close the operator's manual with the product when

handing it over.

 Failure to do so could lead to an accident or serious injury.

Being prepared in case of an injury

In the unlikely event of an accident or injury, please ensure

that you are prepared.



First aid kit



Towels and wipes (to stop any bleeding)



Whistle or mobile phone (for calling outside help)

 If you are unable to perform first aid or call for outside help,

the injury could worsen.

DANGER

Do not use the product when the trimmer blade is

turning at idle speed



You must not use the product while the trimmer blade is

turning if the Grass Trimmer is running with the throttle

trigger in the idle speed position.

 To do so could lead to an accident or serious injury.

Do not remove the shield



Do not operate the product without the shield in place.

 Any objects that ricochet off the trimmer blade could cause

an accident or serious injury.

The area within a 15 m radius is a danger zone

The area within a 15 m radius of the product is a danger

zone. Be careful to observe the following precautions

while working with the product.



Do not allow children and other people or pets to enter

the danger zone.



If another person enters the danger zone, turn off the

engine to stop the blade from rotating



When approaching the operator, signal to him by, for

example, throwing twigs from outside the danger zone,

and then check that engine has been switched off and

the blade has stopped turning



If more than one person is working with the product,

identify the way in which you will signal to each other

and work at least 15 m apart

 Any objects that ricochet off the trimmer blade, and any con-

tact with the trimmer blade, could cause blindness or a fatal

accident.

For safe use of your product

WARNING

Users of the product

The product should not be used by:



people who are tired



people who have taken alcohol



people who are on medication



people who are pregnant



people who are in poor physical

condition



people who have not read the op-

erator's manual



children

 Failure to observe these instruc-

tions could lead to an accident.

Environment of use and operation



Do not use the product in places where there is no sure

foothold, such as on steep slopes or after rainfall, as

such places are slippery and dangerous.



Do not operate the product at night or in dark places

with poor visibility.



When using the product on a gentle slope, work in a lev-

el, contour-like motion.

 A serious injury could result if you fall or slip, or fail to oper-

ate the product correctly.



For your own health and your safe and comfortable

work, operate the machine within the air temperature

range of -5

C to 40

 Failure to observe these instructions could result in damage

to your health.

Turn off the engine when moving around

When moving around in the situations described below,

turn off the engine and ensure that the trimmer blade has

stopped rotating, then fit the trimmer blade cover and po-

sition the silencer away from yourself.



Moving to the place where you are working



Moving to another area while you are working



Leaving the place where you have been working

 Failure to observe these precautions could cause burns or

serious injury.



When transporting the product by car, empty the fuel

tank, fit the trimmer blade cover, and secure the product

firmly in place to prevent it from moving around.

 Travelling by car with fuel in the trimmer tank could lead to a

fire.

Vibration and cold

It is believed that a condition called Raynaud's Phenome-

non which affects the fingers of certain individuals may be

brought about by exposure to vibration and cold. Expo-

sure to vibration and cold may cause tingling and burning,

followed by loss of colour and numbness in the fingers.

The following precautions are strongly recommended be-

cause the minimum exposure which might trigger the ail-

ment is unknown.



Keep your body warm, especially the head and neck,

feet and ankles, and hands and wrists.



Maintain good blood circulation by performing vigorous

arm exercises during frequent work breaks, and also by

not smoking.



Limit the number of hours of operation.

Try to fill each day with jobs where operating the trim-

mer or other hand-held power equipment is not re-

quired.



If you experience discomfort redness and swelling of

the fingers, followed by whitening and loss of feeling,

consult your physician before exposing yourself further

to cold and vibration.

 Failure to observe these instructions could result in damage

to your health.

Repetitive stress injuries

It is believed that over-using the muscles and tendons of

the fingers, hands, arms and shoulders may cause sore-

ness, swelling, numbness, weakness and extreme pain to

the areas just mentioned. Certain repetitive hand activities

may put you at a high risk for developing a repetitive

stress injury (RSI).

To reduce the risk of RSI, do the following:



Avoid using your wrist in a bent, extended or twisted

position.



Take periodic breaks to minimize repetition and rest

your hands. Reduce the speed and force in which you

do the repetitive movement.



Do exercises to strengthen hand and arm muscles.



See a doctor if you feel tingling, numbness or pain in

your fingers, hands, wrists or arms. The sooner RSI is

diagnosed, the more likely permanent nerve and muscle

damage can be prevented.

 Failure to observe these instructions could result in damage

to your health.

Proper training

Do not permit operation without proper training and protective equipment.

Be thoroughly familiar with the controls and proper use of unit.

Know how to stop the unit and shut off the engine.

Know how to unhook a harnessed unit quickly.

Never allow anyone to use the unit without proper instruction.

For safe use of your product

WARNING

Remove foreign objects and obstructions before working with the

product



Before starting work, check the area where you will be working and re-

move any small stones and empty cans likely to ricochet off the cutting

attachment, as well as any pieces of string or wire that might become

twisted around the cutting attachment.

 An accident or serious injury can occur if foreign objects ricochet off the cut-

ting attachment or wire and other materials twisted round the product spring

off it.

Do not hold the cutting attachment up when working with the product



Do not hold the cutting attachment up while you work. You must not work with the cutting attachments raised above

knee level.

 Raising the cutting attachment above knee level brings the plane of rotation closer to the face, and any objects that fly off the

cutting attachments could cause an accident or serious injury.

Turn off the engine immediately if anything goes wrong

In the following situations, turn off the engine immediately and ensure that the cutting attachments have stopped be-

fore checking each area of the product. Replace any damaged parts.



If the cutting attachment hits a rock, tree, post, or other such obstruction while you work.



If the product suddenly starts to vibrate abnormally.

 Continuing to use parts when they are damaged could lead to an accident or serious injury.

Kickback



The phenomenon that occurs if the trimmer blade

comes into contact with a tree, post, rock or other hard

object while rotating at high speed and reacts by recoil-

ing powerfully and instantaneously is known as kick-

back.



Causing kickback can result in a loss of control over the

product and is highly dangerous.



In particular, if the front-right quadrant of the trimmer

blade (B) strikes a shrub or other such object, the trim-

mer blade will cause the product to recoil sharply back-

wards to the right.



To prevent kickback, do not trim from left to right. Be

careful to ensure that the trimmer blade does not strike

any hard objects.



When trimming, ensure that the object you are cutting

meets the portion of the blade 1/3 in from the front edge

on the left-hand side (A).

 Failure to do so could cause an injury or fatal accident.

For safe use of your product

Precautions concerning the cutting attachment

1.With metal blade

2.With nylon line cutting head

DANGER

Always stop the engine when a cutting attachment jam occurs. Do not attempt to remove an object causing a jam if the

engine is running. Severe injury can occur if a jam is removed and the cutting attachment suddenly starts.

WARNING

Use correct blades



Serious injury may result from the improper use of

blades. Read and comply with all safety instructions

listed in this manual.



Use only cutting attachments recommended by YAMA-

BIKO CORPORATION.



The type of blade used must be matched to the type and

size of material cut. An improper or dull blade can cause

serious personal injury. Blades must be sharp. Dull

blades increase the chance of kick-out and injury to

yourself and bystanders.



Plastic/Nylon Grass/Weed Blades may be used

where ever the nylon line head is used. Do not use

this blade for heavy weeds or brush.



The 3 cutter blade is designed especially to cut

weeds and grass. To avoid injury due to kickback or

blade fracture, do not use the 3 cutter blade to cut

brush or trees.



8 Tooth Weed/Grass Blade is designed for grass, gar-

den debris and thick weeds. Do not use this blade for

brush or heavy woody growth, 19 mm diameter or

larger.



80 Tooth Brush Blade is designed for cutting brush

and woody growth up to 13 mm diameter.



22 Tooth Clearing Blade is designed for dense thick-

ets and saplings up to 64 mm diameter.

Inspect blade before use

Pieces from a cracked metal blade can fly off during oper-

ation. Inspect metal blades for cracks before each use.

Discard cracked blades no matter how small the crack.

Cracked blades can be the result of the misuse or improp-

er sharpening.

 Damaged or shattered blades can cause accidents and se-

rious injury.

Reaction forces

Be sure you understand the reaction forces of push and

pull, and kickback described in this manual, and how

these forces may affect your balance in the operation of a

unit.

 Failure to do so could cause an injury or fatal accident.

WARNING

Use correct cutting attachment



Serious injury may result from the improper use of cut-

ting attachment.

Read and comply with all safety instructions listed in

this manual.



Use only cutting attachments recommended by YAMA-

BIKO CORPORATION.



Use only nylon line cutting head. Do not use any type of

metal blade.

 Failure to do so could lead to an accident or serious injury.



Excessive nylon line beyond cut off knife could fly off

when the nylon line cutting head starts rotating after ad-

justment of nylon line length.

 Failure to do so could lead to an accident or injury.

Do not trim near cars or pedestrians

Use extreme caution when operating over bare spots and

gravel, because the line can throw small rock particles at

high speeds. The shield on the unit cannot stop objects

which bounce or ricochet off hard surfaces.

 Failure to do so could lead to an accident or serious injury.

Avoid wire

Do not trim in any area where there are broken strands of

fencing wire. Remove the broken pieces of wire, or give the

area wide berth. Wear proper safety protection. Do not cut

where you cannot see what the cutting device is cutting.

 Failure to do so could lead to an accident or serious injury.

CAUTION

Use only flexible, non-metallic line recommended by YAMABIKO CORPORATION.

For safe use of your product

Protective gear

WARNING

Wear protective gear

Always wear the following protective gear when working

with the trimmer.

a Head protection (helmet): Protects the head

b Ear muffs or ear plugs: Protect the hearing

c Safety goggles: Protect the eyes

d Face shield: Protects the face

e Safety gloves: Protect the hands from cold and vibration

f Work clothes that fit (long sleeves, long trousers): Pro-

tect the body

g Heavy duty, non-slip protective boots (with toecaps) or

non-slip work shoes (with toecaps): Protect the feet

h Shin guards: Protect the legs

 Failure to observe these precautions could result in damage

to your sight or hearing, or lead to a serious injury.

When necessary, please use the protective gear below.

Dust mask: Protects the breathing apparatus

Bee net: To deal with attacks by bees

Wear proper clothing.

Do not wear ties, jewellery, or loose, dangling clothing which could be

caught in the unit. Do not wear open toed footwear, or go bare-foot or

barelegged. In certain situations, total face and head protection may be re-

quired. For heavy brush cutting with metal blade, logger's trousers or leg

chaps with protective inserts are added considerations.

 Failure to observe these precautions could result in damage to your sight or

hearing, or lead to a serious injury.

Packing list

 The following parts are packed separately in the packing box.

 When you have unpacked the box, please check the parts that it contains.

 Contact your dealer if anything is missing or broken.

Engine

Operation Shaft

1. Engine

2. 3 cutter blade

3. Safety goggles (ANSI Z 87.1 compliant)

4. Caution tag

5. Operator's manual

6. Shield (for metal blade)

7. Shield (for nylon line cutting head)

8. Locking tool

9. Socket wrench

10. Hexagonal wrench

11. Flexible shaft assembly

12. Shaft tube

13. Blade cover

14. Front handle

15. Strap

Description

1. Cutting attachment 3 cutter blade for cutting grass, gar-

den debris and weeds.

2. Shield Device to protect the operator from accidental

contact with the cutting head and thrown objects.

3. Angle transmission Having two gears to change to an-

gle of rotating axis.

4. Shaft tube Part of the unit that provides a casing for pow-

er transmission shaft.

5. Front handle Handle located towards the cutting device.

6. Strap Rubber strap to hang power transmission shaft.

7. Ignition switch "Slide switch" mounted on top of the

throttle trigger housing, move switch upward to RUN,

downward to STOP position.

8. Throttle trigger Activated by the operator's finger for con-

trolling the engine speed.

9. Throttle trigger lockout Locks throttle trigger in the idling

position until you have a proper grip with your right hand

around the handle.

10. Rear handle Handle located towards the knapsack pow-

er unit.

11. Flexible shaft assembley Flexible tube for the power

transmission shaft.

12. Silencer cover Cover the silencer not to make operator

touch to hot surface of silencer.

13. Spark plug

14. Air cleaner cover Covers air filter.

15. Fuel tank Contains fuel and fuel filter.

16. Fuel tank cap For closing the fuel tank.

17. Starter handle Pull handle to start the engine.

18. Blade cover When transporting the unit, use the appro-

priate metal blade cover.

Before you start

Before yo u start

Assembly

Flexible shaft assembly

First stage of assembling is coupling of the power transmission

shaft (F) and (R).

 Loosen bolt with hexagonal wrench.

 Insert the power transmission shaft (R) with the spacer into the

socket gradually and fully. - The socket is assembled on the

power transmission shaft (F) and located inside of the rear

handle. - The spacer that is located at the end of the power

transmission shaft (R) prevents the shaft (R) from loosening

off.

 Insert connector into holder and tighten bolt securely using

hexagonal wrench.

Second stage is coupling of the power transmission shaft (R) and

the engine.

 As pushing in the lock pin fully, insert the other end of power

transmission (R) to the driving shaft of the engine. - For easier

coupling, pull out the power transmission (R) about 4 mm

Shindaiwa BP520S Manuel utilisateur

Marque: Shindaiwa

Modèle: BP520S

Catégorie: Coupe-herbe

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

italiano: Shindaiwa BP520S Manuale utente
English: Shindaiwa BP520S User manual
Deutsch: Shindaiwa BP520S Benutzerhandbuch

Shindaiwa BP520S Manuel utilisateur

Shindaiwa BP520S Manuel utilisateur

dans d''autres langues

Documents connexes