Monogram ZIP360NH Guide d'installation

Monogram.com

INSTALLATION

INSTRUCTIONS

with Design Guide

36” Built-In French Door,

Bottom-Freezer Refrigerators

Pour obtenir une version française de ce manuel d’instructions,

visitez notre site monogram.com.

Para consultar una version en español de este manual de

instrucciones, visite nuestro sitio de internet monogram.com.

2

Safety Information

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT – Save these instructions for

local inspector’s use. Observe all governing codes and

ordinances.

•

Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these instructions with

your Owner’s Manual for future reference.

If you received a damaged unit, you should immediately

contact your dealer or builder.

Skill Level – Installation of this unit requires basic

mechanical, carpentry and plumbing skills. Proper

installation is the responsibility of the installer. Product

failure due to improper installation is not covered under

the Monogram Warranty. See the Owner’s Manual for

warranty information.

For Monogram local service in your area, call 1.800.444.1845 or visit monogram.com.

For Monogram service in Canada, call 1.800.561.3344

For Monogram Parts and Accessories, call 1.800.444.1845 or visit monogram.com.

WARNING

Tip Over Hazard.

These appliances are top heavy, especially with any doors open, and must be secured to prevent tipping

forward which could result in death or serious injury. Read and follow the entire installation instructions for

securing the appliance with the anti-tip system.

WARNING

Explosion Hazard.

Keep flammable materials and vapors, such as gasoline, away from appliance. Failure to do so can result

in fire, explosion, or death.

WARNING

To reduce the risk associated with choking, do not allow children under 3 years of age to

have access to small parts during the installation of this product.

CAUTION

Lifting Hazard

This unit is very heavy. To reduce the risk of person injury during maneuvering and installing this appliance,

3 people are required for proper installation.

CAUTION

Keep fingers out of the “pinch point” areas; clearances between the doors and between the

doors and cabinet are necessarily small. Be careful closing doors when children are in the area.

WARNING

Electrical Shock Hazard.

Plug into a grounded 3-prong outlet.

Do not remove the ground prong.

Do not use an adapter.

Immediately discontinue use of a damaged supply cord.

If the supply cord is damaged it must be replaced by a

qualified service professional with an authorized service

part from the manufacturer.

Do not use an extension cord with this appliance.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Follow the instructions in the section Grounding the unit.

This appliance must be installed with a means in the

fixed house wiring or circuit breaker for disconnecting the

appliance from the electrical supply after installation.

31-49141 Rev. 2

3

Consignes de sécurité

AVANT DE COMMENCER

Veuillez lire toutes ces instructions attentivement.

• IMPORTANT – Conservez ces instructions à

l’usage de l’inspecteur local. Observez tous les codes et

décrets en vigueur.

•

Note à l’installateur – Assurez-vous de laisser ces

instructions au consommateur.

•

Note au consommateur - Conservez ces instructions

avec votre manuel d’utilisation pour

consultation ultérieure.

Si vous avez reçu un appareil endommagé, veuillez

communiquer immédiatement avec votre revendeur ou votre

entrepreneur.

Niveau de compétence – L’installation de cet appareil

exige des compétences de base en mécanique, menuiserie

et plomberie. La responsabilité d’une installation adéquate

relève de l’installateur. La garantie Monogram ne couvre

pas les défectuosités du produit causées par une installation

inadéquate. Consultez le manuel d’utilisation pour des

renseignements sur la garantie.

Pour joindre le service Monogram de votre région, composez le 1.800.444.1845 ou visitez monogram.com.

Pour le service Monogram au Canada, composez le 1.800.561.3344.

Pour le service des Pièces et accessoires Monogram, composez le 1.800.444.1845 ou visitez monogram.com.

AVERTISSEMENT

Risque de basculement.

Ces électroménagers sont lourds du haut, notamment lorsqu’une porte est ouverte, de sorte qu’ils doivent être fixés pour

prévenir un basculement vers l’avant susceptible d’occasionner des blessures graves ou la mort. Lisez et observez la totalité des

instructions d’installation pour connaître la façon de fixer l’électroménager sur le dispositif antibasculement.

AVERTISSEMENT

Risque d’explosion.

Gardez les matières et les vapeurs inflammables telles que l’essence à distance de l’électroménager. L’omission de prendre cette

précaution peut entraîner un incendie, une explosion ou la mort.

AVERTISSEMENT

Pour réduire le risque d’étouffement pendant l’installation de ce produit, ne pas laisser les petites pièces

à la portée des enfants âgés de moins de 3 ans.

AVERTISSEMENT

Risque lié à la manipulation d’un objet lourd

Cet appareil est très lourd. Afin de réduire le risque de blessure pendant la manipulation et l’installation de cet électroménager, la

participation de 3 personnes est nécessaire à l’exécution d’une installation correcte.

AVERTISSEMENT

Gardez vos doigts éloignés des points de pincement. Les espaces entre les portes et ceux entre les

portes et l’armoire sont particulièrement restreints. Soyez prudent lorsque vous fermez les portes en présence d’enfants.

AVERTISSEMENT

Risque d’électrocution.

Branchez l’appareil dans une prise à 3 broches mise à la terre.

N’enlevez pas la broche de mise à la terre.

N’utilisez pas un adaptateur.

Cessez immédiatement l’utilisation d’un cordon électrique

endommagé. Si le cordon électrique est endommagé, son

remplacement doit être exécuté par un technicien en réparation

qualifié au moyen d’un cordon de rechange autorisé par le

fabricant.

N’utilisez pas un cordon de rallonge avec cet électroménager.

Le non-respect de ces instructions peut occasionner un décès,

un incendie ou un choc électrique

Suivez les instructions de la section Mise à la terre de l’appareil.

Le circuit électrique auquel cet électroménager sera raccordé

doit comporter un disjoncteur ou un autre dispositif permettant

de couper l’alimentation électrique à l’appareil après l’installation.

31-49141 Rev. 2

4

Información sobre Seguridad

ANTES DE COMENZAR

Lea estas instrucciones en su totalidad y atentamente.

•

IMPORTANTE – Conserve estas

instrucciones para uso del inspector local. Cumpla con

todos los códigos y ordenanzas gubernamentales.

•

Nota para el Instalador – Asegúrese de entregarle

estas instrucciones al Comprador.

• Nota para el Consumidor – Guarde estas

instrucciones con su Manual del Propietario para

referencia futura.

Si la unidad que recibió está dañada, se deberá

comunicar de inmediato con su vendedor o fabricante.

Nivel de habilidad – La instalación de esta unidad

requiere un nivel básico de habilidades mecánicas,

de carpintería y plomería. La correcta instalación

del producto es responsabilidad del instalador. Si se

producen fallas en el producto debido a una instalación

inadecuada, la Garantía de Monogram no cubrirá las

mismas. Para obtener información sobre la garantía,

consulte el Manual del Propietario.

Para acceder al servicio local de Monogram en su área, llame al 1.800.444.1845 o visite monogram.com.

Para acceder al servicio de Monogram en Canadá, llame al 1.800.561.3344.

Para acceder a Piezas y Accesorios de Monogram, llame al 1.800.444.1845 o visite monogram.com.

ADVERTENCIA

Riesgo de Caídas

Estos electrodomésticos son inestables, especialmente cuando una puerta se encuentre abierta, y deben estar

asegurados a fin de evitar caídas hacia adelante que podrían resultar en la muerte o en lesiones graves. Lea y siga

las instrucciones de instalación en su totalidad para asegurar el electrodoméstico con el sistema anti volcaduras.

ADVERTENCIA

Riesgo de Explosión

Mantenga cualquier material y vapores inflamables, tales como gasolina, alejados del electrodoméstico. Si no se

cumple con esto, se podrá producir una explosión, un incendio o la muerte.

ADVERTENCIA

A fin de reducir el riesgo asociado con descargas, no permita que los niños menores de 3

años de edad tengan acceso a las partes pequeñas durante la instalación de este producto.

PRECAUCIÓN

Riesgo al levantar la puerta

Este refrigerador es muy pesado. A fin de reducir el riesgo de lesiones personales durante la maniobra e instalación

de este refrigerador, se requiere contar con 3 personas para una correcta instalación del modelo de 36” de ancho y

con 4 personas para una correcta instalación del modelo de 42” o 48”.

PRECAUCIÓN

Mantenga los dedos fuera de los espacios de “riesgo de lastimaduras”; los espacios entre

las puertas y entre las puertas y el gabinete son necesariamente pequeños. Tenga el cuidado de cerrar las puertas

cuando se encuentren niños en el área.

ADVERTENCIA

Riesgo de Descarga Eléctrica

Enchufe en un tomacorriente con conexión a tierra de 3

cables.

No elimine el cable de conexión a tierra.

No use un adaptador.

Inmediatamente interrumpa el uso de un cable de

suministro de corriente dañado. Si el cable de corriente se

encuentra dañado, su reemplazo deberá ser realizado por

un profesional calificado del servicio técnico, utilizando una

pieza del servicio técnico autorizada por el fabricante.

No use prolongadores con este electrodoméstico.

Si no se siguen estas instrucciones, se podrá producir la

muerte, incendios o descargas eléctricas.

Siga las instrucciones que figuran en la sección de

Conexión de Tierra de la unidad.

Este electrodoméstico deberá ser instalado por algún

medio en el cableado fijo del hogar o en un disyuntor para

desconectar el electrodoméstico del suministro eléctrico

luego de la instalación.

31-49141 Rev. 2

5

Contents

Safety 2

Instructions for Standard Installation 6

Design Guide

The Installation Space 7

Dimensions and Clearances 7

Custom Handle Design Guide 8

Customization Basics 8

Refrigerator Location 8

3/4” Overlay Panel Dimensions 9

1/4” Framed Panel Dimensions 10

Side Panels 10

130° Door Swing 11

90° Door Swing 12

Installation Instructions

Tools, Hardware, Materials, Flooring 13

Refrigerator Location 13

Grounding the Unit 13

Step 1. Remove Packaging 14

Step 2. Install Water Line 14

Step 2A. Water Line with Reverse

Osmosis System 15

Step 3. Install Side Panels 15

Step 4. Anti-Tip Procedures 15

Step 5. Level Refrigerator 17

Step 6, Secure Unit to Wall 17

Step 7. Alternate Anti-Tip Procedure 18

Step 8. Adjust Door Swing 18

Step 9, Install Grille Panel 19

Step 10, Install 1/4” Framed Panels 19

Step 10A, Install Overlay Panels 20

Step 11. Connect Water Supply 21

Step 12. Connect Power 21

Step 13. Start Icemaker 22

Step 14. Install Toekick 22

Inspect Final Installation 22

Instructions for Flush Inset Installation 23

Design Guide

The Installation Space 24

Dimensions and Clearances 24

Custom Handle Design Guide 24

1/2” Overlay Panel Dimensions 25

3/4” Decorative Panel Dimensions 26

Customization Basics 26

Refrigerator Location 26

3/4” Raised Fresh Food Door Panel Routing 27

3/4” Raised Freezer Drawer Panel Routing 28

3/4” Raised Grille Panel Routing 29

Side Panels 30

Side Cleats 30

Installation Instructions

Tools, Hardware, Materials, Flooring 31

Grounding the Refrigerator 31

Step 1. Remove Packaging 32

Step 2. Install Water Line 32

Step 2A. Water Line with Reverse

Osmosis System 33

Step 3. Install Side Panels 33

Step 4. Install Case Trim 33

Step 5. Anti-Tip Procedure 33

Step 6. Level Refrigerator 35

Step 7. Secure Unit to Wall 35

Step 8. Alternate Anti-Tip Procedure 36

Step 9. Adjust Door Swing 36

Step 10. Install Grille Panel 37

Step 11. Install Assembled Panels 37

Step 12. Connect Water Supply 38

Step 13. Connect Power 38

Step 14. Start Icemaker 38

Step 15. Install Toekick 39

Inspect Final Installation 39

Instructions for Stainless Steel Installation 40

Design Guide

The Installation Space 41

Dimensions and Clearances 41

Customization Basics 42

Side Panels 42

Refrigerator Location 42

130° Door Swing 43

90° Door Swing 44

Installation Instructions

Tools, Hardware, Materials, Flooring 45

Grounding the Refrigerator 45

Step 1. Remove Packaging 46

Step 2. Install Water Line 46

Step 2A. Water Line with Reverse

Osmosis System 47

Step 3. Install Side Panels 47

Step 4. Anti-Tip Procedure 47

Step 5. Level Refrigerator 49

Step 6, Secure Unit to Wall 49

Step 7. Alternate Anti-Tip Procedure 50

Step 8. Adjust Door Swing 50

Step 9. Connect Water Supply 51

Step 10. Connect Power 51

Step 11. Start Icemaker 51

Step 12. Install Toekick 52

Inspect Final Installation 52

31-49141 Rev. 2

6

Instructions for Standard Installation

31-49141 Rev. 2

7

Design Guide - Standard Installation

36" Frame to

Frame Width

*84" From

Floor to

Top Frame

35"

Case Width

*83 1/2"

at

Rear

25-3/8"

Case Depth

Depth Including

THE INSTALLATION SPACE

Water And Electrical Locations

Electrical and water supply must be located as shown.

The cutout depth must be 24” (60.96 cm)

The refrigerator will project forward, slightly beyond

adjacent cabinetry, depending on your installation.

Allow minimum 1/8” (0.32 cm) air gap between case

back & wall.

Cutout depth beneath a soffit:

When installed beneath a soffit, the soffit cannot

exceed the 24” (60.96 cm) installation depth shown.

The top case trim overlaps the bottom of the soffit.

Additional Specifications

• A 115 volt 60Hz., 15 or 20 amp power supply is

required. An individual properly grounded branch

circuit or circuit breaker is recommended. Install

a properly grounded 3-prong electrical receptacle

recessed into the back wall. Electrical must be

located on rear wall as shown.

• Water line can enter the opening through the floor

or back wall. Route SmartConnect

™

kit or 1/4” O.D.

copper tubing between the cold water line and the

water connection location. The tubing should be

long enough to extend to the front of the refrigerator.

Installation of an easily accessible shut-off valve in

the water line is required.

DIMENSIONS AND CLEARANCES

* Shipping height. The

refrigerator can be

adjusted to fit into a

cutout that is 83-1/2

”

(212 cm) min. to 84-1/2

”

(214.63 cm) max.

height. Note that the top

case trim at the front is

1/2

” (1.27 cm) higher

and will overlap upper

cabinetry or soffit. Use

leveling legs and wheels

for a maximum 1

” (2.54

cm) height adjustment.

Product Clearances

These refrigerators are equipped with a 3-position

door stop. The factory set 115° door swing can be

adjusted to 90° if clearance to adjacent cabinets or

walls is restricted.

23-7/8"

Behind

Frame

90°90°

18-3/16”

4” Min. Distance

to Adjacent Wall

from Cutout

6"

Wall View

Electrical

Area

84-1/2" max

Finished

Opening

75" From

Floor to

Bottom

of Electrical Area

10"

24" Cutout Depth

35-1/2"

Finished Width

2-5/16"

5"

10"

3-1/2" 3-1/2"

5"

3-1/2"

Water Supply

12-1/8"

Min. to

Wall

12-1/8"

Min. to

Wall

130°

The finished

cutout width

must be

35-1/2”.

Allow 12-1/8” (30.80 cm) minimum clearance for a

full 130° door swing.

For a 90° door swing, allow 4” (10.16 cm) min.

clearance to adjacent wall from cutout. If the 90°

door stop position is used, pan access is maintained,

but pan removal is restricted.

See illustrations pages 11 and 12 to determine

door swing interaction with adjacent cabinets or

countertops.

8"

Min. to

Wall

8"

Min. to

Wall

115°

31-49141 Rev. 2

8

CUSTOMIZATION BASICS:

Framed Or Overlay Panels, Custom

Handles and Accessory Kits

These refrigerators are designed to be customized with

decorative panels. Field installed custom door and grille

panels are required.

Side Panels

Side panels must be used whenever the sides of the

refrigerator will be exposed.

Design Guide - Standard Installation

REFRIGERATOR LOCATION

• Do not install the refrigerator where the temperature

will go below 60°F (16°C). It will not run often enough

to maintain proper temperatures.

• Do not install the refrigerator where temperatures will

go above 100°F (37°C). It will not perform properly.

• Do not install the refrigerator in a location exposed to

water (rain, etc.) or direct sunlight.

• Install it on a floor strong enough to support it fully

loaded.

CUSTOM HANDLE DESIGN GUIDE

Custom handles must be used for flush installation. For

custom handle installation, counterbore holes in rear of

decorative panels must ensure 1/2” (1.27 cm) material

thickness remains for handle support.

NOTE: The counterbore must not exceed 1” (2.54 cm)

in diameter.

Minimum distance on Fresh Food Doors from handle

side edge to handle center should be 1-1/4” (3.18 cm)

on each door as shown.

Minimum distance on Freezer Door from top edge to

handle center on the freezer drawer should be 1-1/4”

(3.18 cm) as shown.

7/8"

1-1/10"

3/4"

Countersink screw

into panel as shown.

1-1/4”

31-49141 Rev. 2

9

3/4” (1.91 cm) OVERLAY PANEL DIMENSIONS

For a more custom appearance, overlay panels may be installed on trimmed

models. The overlay panel must be secured to a 1/4” (0.64 cm) thick backer

panel which slides into the trim. A spacer panel 0.10” (0.25 cm) thick must

be placed between the overlay and backer panel.

Assemble the panels with glue and screws.

• Center the spacer panel on the backer panel, left to right and top to

bottom. Secure the panels with glue.

• Refer to the following chart for locating the backer panel to the overlay

panel. Secure the overlay panel to the backer panel with glue and screws.

Screws must be countersunk into the backer panel.

Spacer Panel

Backer Panel

Overlay Panel

NOTE: Left-to-right offset is not always equal

to top-to-bottom offset.

IMPORTANT NOTE: Maximum

total weight for the assembled

panels:

• Fresh food door panels – 30 lbs.

(14 kg)

• Freezer drawer panel – 28 lbs.

(13 kg)

• Grille Panel – 11 lbs. (5 kg)

Design Guide - Standard Installation

Panel Locations

.25" + .10" + .75" = 1.10" Total Panel Thickness

(0.64 + 0.25 + 1.9 = 2.79 cm)

Fresh Food Freezer Grille

1/4” (0.63 cm)

Backer Panel

46-1/16” x 16-1/2”

(116.99 x 14.91 cm)

33-7/8” x 21-7/8”

(86.04 x 55.56 cm)

33-7/8” x 8-7/8”

(86.04 x 22.54 cm)

0.10” (0.25 cm)

Spacer Panel

44-11/16” x 15”

(113.51 x 38.10 cm)

32-1/2” x 20-1/2”

(82.55 x 52.07 cm)

32-1/2” x 7-5/8”

(82.55 x 19.37 cm)

3/4” (1.9 cm)

Overlay Panel

46-5/16” x 16-5/8”

(117.63 x 42.23 cm)

34-1/8” x 22"

(96.67 x 55.88 cm)

34-1/8” x 9”

(96.67 x 22.86 cm)

ABCD

Door Panels 1/8”

(0.32 cm)

0 1/8”

(0.32 cm)

1/8”

(0.32 cm)

Drawer Panel 1/8”

(0.32 cm)

1/8”

(0.32 cm)

1/16”

(0.16 cm)

1/16”

(0.16 cm)

Grille Panel 1/8”

(0.32 cm)

1/8”

(0.32 cm)

1/16”

(0.16 cm)

1/16”

(0.16 cm)

Panel Dimensions

Hinge

Side

Hinge

Side

Handle

Side

Fresh

Food

Back

Backer with

Overlay Panel

Assembly

A

B

C

D

Fresh

Food

Back

A

B

C

D

C

D

A B

Grille Back

C

D

A B

Freezer Back

31-49141 Rev. 2

10

1/4” (0.63 cm) FRAMED PANEL DIMENSIONS

If you choose to install framed panels, they must be

cut to the dimensions shown. The panels will slide

into the frame on the door, drawer and grille.

If the custom panel is less than 1/4” thick and if it fits

loosely in the door frame, it can be backed up with a

piece of filler material or foam tape to improve the fit.

1/4"

Panel

Door

5/16"

Trim

Reveal

Design Guide - Standard Installation

*84"

2-9/16"

24"

*3" to 4"

3/16"

1-7/8"

SIDE PANELS

Side panels must be used whenever the sides of

the refrigerator will be exposed. The 1/4” (0.63 cm)

side panels will slip into the side case trim. Secure

the panels to the refrigerator with stick-on hook and

loop fastener strips. Order the side panels from the

cabinet manufacturer.

• Cut a notch in the top front corner as shown to

allow clearance for corner keys in the front side

trim.

* Depending on

installation height.

NOTE: Maximum total panel weight:

• Fresh food door panel – 58 lbs. (26 kg)

• Freezer drawer panel – 28 lbs. (13 kg)

• Grille Panel – 11 lbs. (5 kg)

Panel Dimensions

1/4” (0.63 cm)

Framed Panel

46-1/16” x 16-1/2”

(101.76 x 41.91 cm)

33-7/8” x 21-7/8”

(86.04 x 55.56 cm)

33-7/8” x 8-7/8”

(86.04 x 22.54 cm)

31-49141 Rev. 2

11

1/4"

1/2"

3/4"

1"

1-1/4"

1"

3/4" Overlay

Panel

(Nominal Size)

Stainless Steel

1/4"

1/2"

3/4"

2"

1-1/4"

1-1/2"

1-3/4"

3"

2-1/4"

2-1/2"

2-3/4"

1/4"

1/2"

3/4"

Door

23-7/8" From

Rear of

Refrigerator

1"

Refrigerator

Case

Trim

Top View

130° DOOR SWING

Scale 1:1

Frameless Cabinets: The case trim

overlaps cabinets at the top and sides.

Therefore, frameless cabinets

may require filler strips to prevent

interference with cabinet door swing.

The opening must allow for filler strips.

Design Guide - Standard Installation

31-49141 Rev. 2

12

1/4"

1/2"

3/4"

1"

1-1/4"

1/4"

1/2"

3/4"

1"

1-1/4"

1-1/2"

23-7/8"

From Rear of

Refrigerator

3/4" Overlay

Panel

(Nominal Size)

Case Trim

Refrigerator

Door

Stainless Steel

Top View

90° DOOR SWING

Scale 1:1

Frameless Cabinets:

The case trim overlaps

cabinets at the top and

sides. Therefore, frameless

cabinets may require

filler strips to prevent

interference with cabinet

door swing. The opening

must allow for filler strips.

Design Guide - Standard Installation

31-49141 Rev. 2

13

Installation Instructions - Standard Installation

TOOLS REQUIRED

• Tinsnips to cut banding • Stepladder

• Bucket • Level

• Appliance Hand Truck • Tubing cutter

• 7/16” open-end wrench • #2 Phillips screwdriver

• Drill and appropriate bits • 5/16”, 7/16” socket

• Safety glasses • 1-1/4” open end wrench

• Pliers • 1/4” ratchet

MATERIALS REQUIRED

• 35” long 2x4 for Anti-Tip support

• 1/4” copper water line tubing or SmartConnect

™

Refrigerator Tubing kits

• Water shut-off valve

• Custom panels for fresh food door, freezer drawer and

grille panel

• Screws to secure refrigerator to cabinetry.

• Stick-on hook and loop fastener strips for 1/4”

(0.63 cm) side panels

HARDWARE SUPPLIED

• Water filter bypass plug

• Anti-Tip brackets

• 1/4” nut and ferrule

• Custom Handle Trim Kit (Shorter box taped to the front

of refrigerator packaging)

• Case Trim - not required for standard installation

(Longer box taped to the front of refrigerator

packaging)

FLOORING

For proper installation, this refrigerator must be placed

on a level surface of hard material that is at the same

height as the rest of the flooring. This surface should be

strong enough to support a fully loaded refrigerator, or

approximately 1,200 lbs. (544.31 kg).

NOTE: Protect the finish of the flooring. Cut a large

section of the cardboard carton and place under the

refrigerator where you are working.

REFRIGERATOR LOCATION

• Do not install the refrigerator where the temperature

will go below 60°F (16°C). It will not run often enough

to maintain proper temperatures.

• Do not install the refrigerator where temperatures will

go above 100°F (37°C). It will not perform properly.

• Do not install the refrigerator in a location exposed to

water (rain, etc.) or direct sunlight.

• Install it on a floor strong enough to support it fully

loaded.

GROUNDING THE REFRIGERATOR

WARNING

Electrical Shock Hazard.

Failure to follow these instructions can result in death,

fire, or electrical shock.

The power cord of this appliance is equipped with a

3-prong (grounding) plug which mates with a standard

3-prong (grounding) wall receptacle to minimize the

possibility of electric shock hazard from this appliance.

Have the wall outlet and circuit checked by a qualified

electrician to make sure the outlet is properly grounded.

Where a standard 2-prong wall outlet is encountered,

it is your personal responsibility and obligation to have

it replaced with a properly grounded 3-prong wall outlet.

DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR

REMOVE THE THIRD (GROUND) PRONG FROM

THE POWER CORD.

DO NOT USE AN ADAPTER PLUG TO

CONNECT THE REFRIGERATOR TO A

2-PRONG OUTLET.

DO NOT USE AN EXTENSION CORD

WITH THIS APPLIANCE.

MISE À LA TERRE DU

RÉFRIGÉRATEUR

AVERTISSEMENT

Risque de choc

électrique.

Le non-respect de ces instructions peut entraîner des

risques d’incendies, des chocs électriques ou la mort.

Le cordon d’alimentation de cet appareil est équipé

d’une fiche à trois broches (pour une mise à la terre)

qui s’adapte à la prise de courant standard à 3

broches (pour une mise à la terre) pour minimiser les

risques de chocs électriques par cet appareil.

Faites vérifier la prise murale et le circuit électrique par

un électricien qualifié pour s’assurer que le système

est correctement mis à la terre.

Dans le cas d’une prise biphasée, l’installateur a la

responsabilité et l’obligation de la remplacer par une

prise triphasée correctement mise à la terre.

NE COUPEZ PAS OU N’ENLEVEZ PAS, SOUS

AUCUN PRÉTEXTE, LA TROISIÈME BROCHE DE

MISE À LA TERRE DU CORDON D’ALIMENTATION.

N’UTILISEZ PAS D’ADAPTATEUR POUR

BRANCHER LE RÉFRIGÉRATEUR À

UNE PRISE BIPHASÉE.

N’UTILISEZ PAS DE RALLONGE AVEC

CET APPAREIL.

31-49141 Rev. 2

14

STEP 1 REMOVE PACKAGING

WARNING

Tip Over Hazard.

Refrigerator is much heavier at the top than at the

bottom. To avoid a risk of death or serious injury,

be careful when moving, and when using a hand

truck, handle only from side.

DO NOT ATTEMPT TO ROLL UNIT OFF SKID.

AVERTISSEMENT

Risque de basculement

Parce que le haut du réfrigérateur est plus lourd que sa

base, la prudence est de mise lors son déplacement, de

l’utilisation d’un diable-brouette, de sa manipulation faite

seulement sur son côté afin d’éviter les blessures graves

ou mortelles.

IL NE FAUT PAS ESSAYER DE FAIRE ROULER

L’APPAREIL MÉNAGER POUR L’ENLEVER DE LAY

PALETTE.

ADVERTENCIA

Riesgo de Caídas

El refrigerador es mucho más pesado en su parte superior

que en su parte inferior – tenga cuidado al moverlo. Al

usar un carro manual, sosténgalo de costado únicamente.

NO INTENTE HACER RODAR LA UNIDAD FUERA DEL

ANTIDESLIZANTE.

Installation Instructions - Standard Installation

CONEXIÓN A TIERRA DEL

REFRIGERADOR

ADVERTENCIA

Riesgo de Descarga

Eléctrica

Si no se siguen estas instrucciones, se podrá producir la

muerte, incendios o descargas eléctricas.

El cable de corriente de este electrodoméstico cuenta con

un enchufe de 3 cables (conexión a tierra) que se conecta a

un tomacorriente de pared estándar de 3 cables (conexión

a tierra) para minimizar el riesgo de posibles descargas

eléctricas por parte del mismo.

Contrate a un electricista calificado para que controle el

tomacorriente y el circuito eléctrico, a fin de asegurar que el

enchufe esté correctamente conectado a tierra.

En caso de contar con un tomacorriente de pared de 2

cables, es su responsabilidad y obligación reemplazarlo

por un tomacorriente de pared de 3 cables correctamente

conectado a tierra.

NUNCA, BAJO NINGUNA CIRCUNSTANCIA, CORTE NI

ELIMINE EL TERCER CABLE (TIERRA) DEL CABLE DE

CORRIENTE.

NO USE UN ENCHUFE ADAPTADOR PARA CONECTAR

EL REFRIGERADOR A UN TOMACORRIENTE DE 2

PATAS.

NO USE UN PROLONGADOR CON ESTE

ELECTRODOMÉSTICO.

• Carefully cut banding

at the top and

bottom, remove the

outer carton.

• Slide out the back

corner posts (2).

• Slide the carton off

the top of the cabinet.

NOTE: IT IS NOT

NECESSARY TO

LAY THE CABINET

DOWN IN ORDER TO

REMOVE THE SKID!

• The unit is secured

to the skid with 2 full-

length tie-down straps. Remove the ten 5/16” bolts

from the base channels in the tie-downs.

• Remove the four 7/16” bolts securing the straps to the

skid.

NOTE: DO NOT ATTEMPT TO ROLL UNIT OFF SKID.

• The support blocks on the bottom of the refrigeration

case must be removed before the refrigerator is taken

off the skid or damage will occur. Carefully tilt the

refrigerator and slide the blocks out from beneath.

• Remove the toekick and set aside for final installation.

• Remove the case trim box and Custom Handle Kit box

and set aside for final installation.

• Lift the refrigerator off the skid with an appliance dolly.

Handle from the sides.

STEP 1 REMOVE PACKAGING (Cont.)

CUSTOM HADNLE TRIM KIT

CASE TRIM

Remove 2 strap

bolts on each side

Remove 5

base channel

bolts on each

side

STEP 2 INSTALL WATER LINE

WARNING

Connect to potable water supply

only.

AVERTISSEMENT

Raccordez l’appareil à une

alimentation d’eau potable seulement.

ADVERTENCIA

Realice la conexión a un

suministro de agua potable únicamente.

• A cold water supply is required for automatic

icemaker operation. The water pressure must be

between 40 and 120 p.s.i. (275-827 kPa).

• Route 1/4” OD copper or SmartConnect

™

plastic

tubing between house cold water line and the water

connection location.

• Tubing should be long enough to extend to the front

of the refrigerator.

Allow enough tubing

to accommodate bend

leading into the water

line connection.

Floor

Waterline Tubing

31-49141 Rev. 2

15

Installation Instructions - Standard Installation

STEP 2 INSTALL WATER LINE

(Cont.)

NOTE: The only Monogram-approved plastic tubing is

supplied in the SmartConnect

™

Refrigerator Tubing kits.

Do not use any other plastic water supply line because

the line is under pressure at all times. Other types of

plastic may crack or rupture with age and cause water

damage to your home.

SmartConnect

™

Refrigerator Tubing Kits are available

in the following lengths:

2’ (.6 m) - WX08X10002 8’ (2.4 m) - WX08X10006

15’ (4.6 m) - WX08X1 0015 25’ (7.6 m) - WX08X10025

Shut off the main water supply.

Turn on the nearest faucet long enough to clear the

line of water.

• Install a shut-off valve between the icemaker water

valve and cold water pipe in a basement or cabinet.

The shut-off valve should be located where it will be

easily accessible.

• Turn on the main water supply and flush debris.

Run about a quart of water through the tubing into a

bucket. Shut off water supply at the shut-off valve.

NOTE: Saddle type shut-off valves are included in

many water supply kits, but are not recommended for

this application.

NOTE: Commonwealth of Massachusetts Plumbing

Codes 248CMR shall be adhered to. Saddle

valves are illegal and use is not permitted in

Massachusetts. Consult with your licensed plumber.

STEP 2A WATER LINE

INSTALLATION WITH A REVERSE

OSMOSIS SYSTEM

Skip this step when not using an RO System

If the water supply to the refrigerator is from a Reverse

Osmosis Water System, use the refrigerator’s filter

bypass plug. Using the refrigerator’s water filtration

cartridge with the RO filter can result in hollow ice

cubes.

Filter Bypass Plug

STEP 3 INSTALL SIDE PANELS

Skip this step when not using side panels.

If you are using 1/4” (0.63 cm) side panels, they should

be inserted into the case trim. Fasten the panels to the

refrigerator with stick-on hook and loop fastener strips

before setting refrigerator in place.

STEP 4 ANTI-TIP PROCEDURE

WARNING

Tip Over Hazard.

These refrigerators are top heavy, especially with

any doors open, and must be secured to prevent

tipping forward which could result in death or

serious injury. Read and follow the entire installation

instructions for securing the refrigerator with the

anti-tip system.

AVERTISSEMENT

Risque de

basculement Ces réfrigérateurs présentent une partie

supérieure lourde, en particulier avec une porte ouverte;

ils doivent donc être fixés pour prévenirle basculement

vers l’avant et le risque concomitant de blessure grave

ou fatale. Lisez et suivez les instructions d’installation

complètes pour l’installation du système anti-basculement.

ADVERTENCIA

Riesgo de Caídas

Estos refrigeradores son inestables, especialmente

cuando una puerta se encuentre abierta, y deberán estar

asegurados a fin de evitar caídas hacia adelante que

podrían resultar en la muerte o en lesiones graves. Lea y

siga las instrucciones de instalación en su totalidad para

asegurar el refrigerador con el sistema anti volcaduras.

• The kit supplied with the unit contains 2 lag bolts and

4 toggles with bolts. The wall bracket will be attached

to the wall in 4 places.

• Measure the opening where the unit is to be installed.

Mark the center with a vertical line.

• Measure up 81 1/2” (207.01 cm) from the floor. Mark

this point on the wall.

31-49141 Rev. 2

16

STEP 4 ANTI-TIP PROCEDURE (CONT)

• Using a level, draw a horizontal line on the wall at this

height.

• Locate at least 2 studs on the back wall. Mark these

points on the horizontal line.

• Place the bottom of the wall bracket with tabs on the

horizontal line. Align the center notch on the bracket

with the center line on the wall.

• The anti-tip wall bracket has a series of holes. Select 2

holes that match with the located studs. Make sure the

holes selected are on the center of the studs. Mark the

wall at these points.

• Mark an additional hole at each end of the bracket.

If one of the studs is closer to the end of the bracket,

mark an additional hole towards the center of the

bracket.

• Drill 1/2” (1.27 cm) holes into the wall board at the

locations marked for the toggles to be mounted (not the

stud markings).

• Drill 3/16” (0.47 cm) holes into wooden studs where

marked. If steel stud construction, drill 1/2” (1.27 cm)

holes into the studs where marked. You will use 2

toggles with the metal studs.

Install Wall Toggles:

The wall toggles and bolts can be ordered as Service Kit

#WR49X10193. Wall toggles are installed in the drywall

and metal studs for stability. Install the wall toggles as

follows:

• Drill 1/2” (1.27 cm) holes at the wall markings made in

the holes at the ends of the wall bracket.

• Hold the metal channel flat against the plastic straps

and slide the channel through the hole.

• Gently pull back at

the ends of the plastic

straps to make the

channel rest flush

behind the wall.

• Hold the ends of the straps in

one hand and slide the plastic

cap along the straps until the

flange of the cap is flush with the

wall.

• Place your thumb between the

plastic straps and bend up and

down to snap the straps off at

the wall.

Installation Instructions - Standard Installation

Line on Wall

Center

Two Additional

Hole Locations at

Ends of Brackets

Center

Wall Bracket

Line On Wall

Wall Studs

Plastic Straps

Metal Channel

Cap

31-49141 Rev. 2

17

Installation Instructions - Standard Installation

STEP 4 ANTI-TIP PROCEDURE

(CONT)

Install Screws and Bolts:

• Have someone hold the

wall bracket centered in

place with each of the

holes aligned with the

correct opening in the

bracket and level with the

horizontal line.

• Insert the lag screws

through the bracket and

into the stud. Tighten

with a wrench.

• Insert the bolts into the

toggle by hand until

snug. Tighten with a

wrench.

CONNECT POWER CORD:

• Before pushing the refrigerator into the opening, plug

the power cord into the receptacle. Open the grille

panel and reach into the opening at the back to grasp

the power cord. Pull the power cord into the opening

as you push the refrigerator back.

• Gently push refrigerator into the opening with hands

against front corners.

IMPORTANT: When the refrigerator is installed under

a soffit or if there is not enough height for this method

of security, brackets cannot be used. Proceed to step

5 to level the refrigerator and then to step 7 to secure

refrigerator to cabinets.

Wood Stud

Lag Screw

Anti-Tip Wall Bracket

Bolt

Wall Toggle

Drywall or

Steel Stud

STEP 5 LEVEL REFRIGERATOR

All models have 4-point leveling. The front is supported

by leveling legs, the rear is supported by adjustable

wheels. Both are accessible from the front of the

refrigerator.

• To level the back of the refrigerator, turn the 7/16” hex

nut located above the front wheels. Turn clockwise to

raise or counterclockwise to lower the refrigerator.

• For front leveling, use a 1-1/4” open-end wrench.

• Adjust height of refrigerator to match installation

cutout opening

83-1/2” (212.09

cm) to 84-1/2”

(214.63 cm). The

refrigerator should

be level and plumb

with cabinetry.

STEP 5 LEVEL REFRIGERATOR

(Cont.)

The rear leveling wheels and front leveling legs are

limited to a maximum height adjustment of 1” (2.54

cm). If the installation requires more than 84-1/2”

(214.63 cm) height, the installer should elevate

the refrigerator on a sheet of plywood or runners.

Cabinetry trim could also be added across the top of

the opening to shorten the opening. If you attempt to

raise the refrigerator more than 1” (2.54 cm), you will

damage the front leveling legs and the rear leveling

wheels.

STEP 6 SECURE UNIT TO WALL

• The “L” rod can be found in the upper left corner of

the unit in the access compartment. Look through the

access compartment to make sure the rod lines up

with the anti-tip bracket.

• There are 2 washers and a hair pin cotter with the rod.

Remove the washers and hair pin cotter from the end

of the rod.

• Rotate and move the

“L” rod into the slot in

the anti-tip bracket tab.

Once it is in the slot,

rotate the “L” rod so the

hook portion is pointing

down. The holes at the

front end of the rod

should be in a vertical

position.

• Pull out on the end of the

rod to make sure it is secure in the bracket.

• Locate the hole on the rod that is closest to the unit.

A hair pin cotter will be put through this hole to secure

the rod. If this hole appears to be too far away for a

snug fit against the unit, add the washers one at a

time until the pin will fit tightly into the hole.

• Align the straight section of the pin with the hole from

the underside of the rod. Push the pin up until it snaps

into position. Pliers may be used. NOTE: The hair pin

cotter must be vertical when this step is completed

to ensure the “L” rod is

engaged in the bracket.

• Check the rod for

tightness by pulling

forward. If the rod

moves, remove the hair

pin cotter and place

another washer on the

rod. Reinsert the pin.

31-49141 Rev. 2

18

Installation Instructions - Standard Installation

STEP 7 ALTERNATE ANTI-TIP

PROCEDURE

The refrigerator must be secured to prevent tipping.

If the anti-tip bracket cannot be used, this alternate

procedure may be used to secure the refrigerator

against tip-over.

• Raise the grille panel to access case trim.

• Use a 3/16” bit to drill four evenly spaced clearance

holes through the metal top case trim.

• Use a 1/16” bit to drill to pilot holes through the metal

clearance holes and into the wood soffit. The holes

should be centered in the soffit or a 3/4” min. wood

brace. The brace spanning the enclosure must be

securely fastened to cabinets on both sides.

• Install four, 1-1/2” (3.81 cm) drywall screws into the

pilot holes.

• If no soffit above the unit, drill screws into adjacent

cabinets through the side case trim.

STEP 8 ADJUST DOOR SWING

NOTE: This refrigerator has a 3-position door stop.

When space does not allow the door to swing open

fully to 115°, you may change the door swing to

a 90° opening. A 130° door swing is available for

standard installation only. If used for flush installation,

damage will occur to wood panels. Skip this step if

door opening is satisfactory for your installation

situation.

• Lift the grille panel to access the wire cover trim.

• Remove screws on both sides of the wire cover trim

and rotate off.

• Use pliers to unscrew door stop and reinstall into the

90° or 130° position.

• Reinstall the wire cover trim.

Remove

Wire Cover

Trim Screws

Pin Location for 90°

Door Swing

Pin Location for

130° Door Swing

Pin Location as

Shipped for 115°

Door Swing

31-49141 Rev. 2

19

Installation Instructions - Standard Installation

STEP 9 INSTALL GRILLE PANEL

• Raise the access panel to the stop position.

• Loosen the screws on the side trim behind the frame.

Remove the bottom trim.

• Slide the panel over the metal baker panel and into the

trim.

• If necessary, tap with a wood block until the panel slips

under the top trim piece.

• Reassemble the bottom trim. Tighten the screws.

• Adjust the hinge spring to accommodate the panel

weight, if necessary.

STEP 10 INSTALL 1/4” (0.63 cm) FRAMED

PANELS

IF YOU ARE INSTALLING OVERLAY PANELS,

GO TO STEP 10A.

Install door and drawer panels:

• Open door to 90°. Remove the 4 Phillips head screws

from the door handle.

• Remove handle. Retain all screws.

• Slide framed panel into the door trim.

• Secure the handle to the door using the screws

removed earlier.

• Follow the same procedures to install the second door

panel.

• For freezer drawer, once panel is installed, use rear

4 screws holes to install the top freezer door trim and

align the handle to the remaining screw holes.

Standard supplied handle shown

31-49141 Rev. 2

20

Installation Instructions - Standard Installation

STEP 10A INSTALL OVERLAY PANELS

CUSTOM HANDLES

If you are using custom handles, the handle must be

properly secured to the panel before sliding the panel into

the trim. Custom Handle Trim Kit is provided with this unit.

Fresh Food Doors

• Beginning with the right fresh food door, slide assembled

door panel into the trim on the door.

• Place the custom handle trim against the side of the

refrigerator door, aligned top to bottom. The holes in the

trim should align to the holes in the door.

• Attach the custom handle trim with the 4 screws previously

removed.

• Remove the paper backing from the mylar tape on the

flange trim cover. Place the flange trim cover onto the

custom handle trim. The tape will help hold the cover in

place. Use shims at the top and bottom of the flange trim

cover, between it and the door, making sure the flange

trim cover fits flush to the custom handle trim. Using the

4 screws provided in custom handle trim kit, secure the

flange trim cover with 2 screws at top and 2 screws at

bottom.

• Repeat these steps with the left fresh food door.

Freezer drawer

• Slide the assembled panel into the drawer trim.

• Secure the original drawer trim using the original round

head trim screws.

IF YOU ARE INSTALLING FRAMED PANELS,

GO TO STEP 10.

Install door and drawer panels:

• Open door to 90°. Remove the 4 Phillips head screws

from the door handle.

• Remove handle. Retain all screws.

• Slide overlay panel into the door trim.

• Secure the handle to the door using the screws

removed earlier.

• Follow the same procedures to install the second door

panel.

• For freezer drawer, once panel is installed, use rear

4 screws holes to install the top freezer door trim and

align the handle to the remaining screw holes.

Supplied handle shown

2-sided

Mylar

Tape

Flange

Trim

Cover

Door

Handle

Trim

Door Trim

and

4 Screws

Double-Sided

Mylar Tape

Located

on Back of

Flange Trim

Cover

Shims

Flange Trim

Cover and

4 Screws

Custom Handle

Trim and 4 Screws

Shims

31-49141 Rev. 2

La page charge ...

Monogram ZIP360NH Guide d'installation

Ce manuel convient également à

Monogram ZIP360NH Guide d'installation

dans d''autres langues

Documents connexes

Autres documents