Amana YNED5800HW0 Mode d'emploi

Marque: Amana

Modèle: YNED5800HW0

Catégorie: Sèche-linge

Taper: Mode d'emploi

Use and Care Guide

Guide d’utilisation et d’entretien

Electronic Dryer

Sécheuse électronique

Para obtener acceso

al Manual de uso y

cuidado en español, o para

obtener información adicional

acerca de su producto, visite:

www.amana.com.

If you have any problems or questions, visit us at www.amana.com

Pour tout problème ou question, consulter www.amana.com

W11553320B

TABLE OF CONTENTS

DRYER SAFETY .......................................................................... 2

ACCESSORIES ........................................................................... 4

CHECK YOUR VENT SYSTEM FOR GOOD AIRFLOW ............... 5

CONTROL PANEL AND FEATURES ............................................ 6

CYCLE GUIDE ............................................................................. 8

USING YOUR DRYER ............................................................... 10

ADDITIONAL FEATURES ........................................................... 12

DRYER CARE ............................................................................ 12

TROUBLESHOOTING ............................................................... 14

WARRANTY ............................................................................... 17

ASSISTANCE OR SERVICE ......................................... Back Cover

TABLE DE MATIÈRES

SÉCURITÉ DE LA SÉCHEUSE .................................................. 18

ACCESSOIRES ......................................................................... 20

VÉRIFICATION D’UNE CIRCULATION D’AIR ADÉQUATE

POUR LE SYSTÈME D’ÉVACUATION ....................................... 21

TABLEAU DE COMMANDE ET CARACTÉRISTIQUES ............. 22

GUIDE DE PROGRAMMES ....................................................... 24

UTILISATION DE LA SÉCHEUSE .............................................. 27

CARACTÉRISTIQUES SUPPLÉMENTAIRES ............................. 29

ENTRETIEN DE LA SÉCHEUSE ................................................ 30

DÉPANNAGE ............................................................................. 32

GARANTIE ................................................................................. 35

ASSISTANCE OU SERVICE ...............................Couverture arrière

You can be killed or seriously injured if you don't immediately

You can be killed or seriously injured if you don't follow

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

DRYER SAFETY

In the State of Massachusetts, the following installation instructions apply:

■ Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gas fitter qualified or licensed by

the State of Massachusetts.

■ Acceptable Shut-off Devices: Gas Cocks and Ball Valves installed for use shall be listed.

■ A flexible gas connector, when used, must not exceed 4 feet (121.9 cm).

WARNING:

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious injury, death, or property

damage.

–

or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

–

the gas supplier.

•Do not try to light any appliance.

•Do not touch any electrical switch; do not use any phone in your building.

•Clear the room, building, or area of all occupants.

•Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s

instructions.

•

ACCESSORIES

Accessories designed for your appliance:

Customize your new washer and dryer with the following genuine

Whirlpool accessories. For more information on options and

ordering, call 1-800-442-9991, or visit us at:

www.amana.com/help.

In Canada, call 1-800-807-6777 or visit us at:

www.amana.com/help

15" Pedestal

Color-matched pedestals raise the

washer and dryer to a more comfortable

working height. The large drawer

provides convenient storage.

Stack Kit

If space is at a premium, the stack kit

allows the dryer to be installed on top of

the washer.

Drying Rack

The Drying Rack provides a

stationary drying surface for items

such as sweaters and tennis

shoes. See the “Additional

Features” section for more

information.

INSTALLATION & MAINTENANCE

ACCESSORIES

FACTORY CERTIFIED PARTS – these three

words represent quality parts and accessories

Time tested engineering that meets

FACTORY CERTIFIED PARTS

Open valve

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent.

Failure to follow these instructions can result in

death or fire.

Good airow

Along with heat, dryers require good airow to efciently

dry laundry. Proper venting will reduce your drying

times and improve your energy savings. See Installation

Instructions.

The venting system attached to the dryer plays a big role in

good airow.

Service calls caused by improper venting are not covered

by the warranty and will be paid by the customer,

regardless of who installed the dryer.

Good airow

■Clean your lint screen before each load.

■Replace plastic or foil vent material with

4" (102 mm) diameter heavy, rigid vent

material.

■Use the shortest length of vent possible.

■Use no more than four 90° elbows in a vent system.

Each bend and curve reduces airow.

■Remove lint and debris from the exhaust hood.

■Remove lint from the entire length of the vent system

at least every 2 years. When cleaning is complete, be

sure to follow the Installation Instructions supplied with

your dryer for nal product check.

■Clear away items from the front of the dryer.

Better Good

102 mm

CHECK YOUR VENT SYSTEM FOR GOOD AIRFLOW

Use Sensor Cycles for better fabric care and energy savings

Use the Sensor Cycles to provide the most energy savings and enhanced fabric care from the dryer. During Sensor Cycles,

drying air temperature and moisture level are sensed in the load. This sensing occurs throughout the drying cycle and the

dryer shuts off when the load reaches the selected dryness. Use the Normal dryness level to provide optimal energy savings.

With Timed Dry, the dryer runs the amount of time set and sometimes results in shrinkage, wrinkling, and static due to

overdrying. Use Timed Dry for the occasional damp load that needs a little more drying time or when using the drying rack.

Eco Dry option

The Eco Dry option will default on only for the Normal cycle and is only available on that cycle.

This option allows you to increase your energy savings by using a slightly lower heat level. The Eco Dry option will increase

drying times by approximately 40 minutes, which will be reected on the LED Display. If optimal time is desired, touch ECO

DRY to turn off this option.

CONTROL PANEL AND FEATURES

Not all features and cycles are available on all models.

NOTE: The control panel features a sensitive surface that responds to a light touch of your nger. To ensure your selections are

registered, touch the control panel with your ngertip, not your ngernail. When selecting a setting or option, simply touch the

appropriate button.

123 6

POWER

Touch to turn the dryer on and off. Touch to stop/cancel a

cycle at any time.

CYCLES

Touch a button for the desired drying cycle. See “Cycle

Guide” for cycle details.

START/PAUSE

Touch and hold until LED counts down “3-2-1” and the dryer

starts; then let go to start a cycle, or touch once while a

cycle is in process to pause it.

MODIFIERS

Use to select available modiers for your dryer. Not all cycles

and options are available on all models.

Temp

When using Timed Dry/Quick Cycle, you may select a dry

temperature based on the type of load you are drying.

Use the warmest setting that is safe for the garments in

the load. Follow garment label instructions.

Dryness

You may adjust the Dryness on Sensor cycles (except for

the Sanitize cycle), if desired.

NOTE: Dryness is for use with Sensor cycles only.

More Time/Less Time Timed Dry Adjust

Touch MORE TIME or LESS TIME with the Timed Dry/

Quick cycle to increase or decrease the length of the

cycle.

OPTIONS

Use to select available options for your dryer. Not all cycles

and options are available on all models.

Wrinkle Prevent Option

If you will be unable to remove a load immediately, touch

WRINKLE PREVENT to add up to 150 minutes of periodic

tumbling to help reduce wrinkling.

NOTE: If you open the dryer door prior to the end of the

Wrinkle Prevent option, the dryer will go into standby.

Cycle Signal

Use this option to turn the signal indicating the end of a

drying cycle to low, medium, high, or off. The volume you

select here will also be applied to the Damp Dry Signal.

NOTE: You may also turn off the tones that sound when a

feature, setting, or option is touched. Touch and hold

CYCLE SIGNAL for about 3 seconds to turn sounds to

low, medium, high, or off.

Damp Dry Signal

Touch to turn the Damp Dry Signal on or off. When

selected, a series of beeps will sound when the load

is damp, but not completely dry. This will allow you

to takeclothes out of the load that do not need to dry

completely. This option is available on some cycles. The

Damp Dry signal is selected as a default for the Bulky Items/

Normal, Bulky Items/Wrinkle Control, and Bulky Items/

Heavy Duty cycles, as a reminder to manually reposition

bulky loads midway through the cycle.

Control Lock

Use this option to lock the controls of the dryer and avoid an

accidental change in cycle options or preferences during a

drying cycle. Touch and hold CONTROL LOCK for 3 seconds

to lock or unlock the controls of the dryer. During this time,

the LED Display will count down “3-2-1.” Once the controls

are locked, the LED Display will display “Loc.”

NOTE: The Control Lock function may be enabled when

recovering from a power failure. To unlock the control, touch

and hold CONTROL LOCK for at least 3 seconds.

Eco Dry Option

The Eco Dry option will default on only for the Normal cycle

and is only available on that cycle. This option allows you

to increase your energy savings by using a slightly lower

heat level. The Eco Dry option will increase drying times by

approximately 40 minutes, which will be reected on the LED

Display. If optimal time is desired, touch ECO DRY to turn off

this option.

LED DISPLAY

When you select a cycle, its default settings will light up and

the Estimated Time Remaining (for Automatic Cycles) will

vary depending on the cycle selection, or actual time

remaining for Timed Dry cycles (for Manual Cycles) will be

displayed.

CYCLE STATUS INDICATORS

The Cycle Status Indicators show the progress of a cycle. Not all

indicators are available on all models.

Sensing

The Sensing indicator will light periodically during Sensor Cycles

to indicate that the moisture sensor on the dryer is operating.

This indicator will not light during Timed Cycles or options such

as Wrinkle Prevent.

Wet

The load is still wet and/or the cycle just started.

Damp

This indicator shows that the load is partially dried and items

that you may wish to hang up or iron while still damp may be

removed.

Cool Down

The dryer has nished drying with heat and is now tumbling the

load without heat to cool it down.

Check Vent

The Check Vent indicator is a feature available for Automatic

cycles only. This indicator will show the status of airow through

the dryer and the dryer vent system for the dryer’s life. During the

sensing phase at the beginning of the cycle, the Check Vent light

will come on if a blocked vent or low airow issue is detected.

This light will stay on for the entire cycle. Should the Check

Vent light illuminate, refer to the “Troubleshooting” section for

potential solutions to the issue.

The light will be cleared upon completion of the cycle, touching

Power, or opening the door. The Check Vent light will continue to

illuminate during the cycle unless the root cause is resolved.

REMEMBER: The dryer will continue to operate even while the

indicator is lit, but poor airow can impact dry times and overall

performance. For more information on maintaining good airow,

see “Check Your Vent System for Good Airow.”

NOTE: If there are other error issues during a cycle, the Check

Vent indicator will not light up. See the “Troubleshooting” section.

End

This will indicate that the selected cycle has ended and the load

may be removed from the dryer. If Wrinkle Prevent has been

selected, the dryer may continue to tumble the load, even if

“End” is displayed.

Control Lock

This will illuminate once the controls are locked.

CYCLE GUIDE — SENSOR CYCLES

Settings and options shown in bold are default settings for that cycle.

If settings are changed, the new settings will be remembered. If there is a power failure, settings will return to the default.

Not all features and cycles are available on all models.

Not all settings and options are available on each cycle.

Use Sensor Cycles for better fabric care and energy savings

The dryer senses moisture in the load or air temperature and shuts off when the load reaches the selected dryness level. Use the

Normal dryness level to provide optimal energy savings.

Items to dry: Cycle: Drying

Temperature: Dryness

Level: Default

Time: Available

Options: Cycle Details:

Shirts, blouses,

permanent

press, synthetics,

lightweight items

Regular High

Medium

Low

Air

Normal

Less

48 Wrinkle Prevent

Cycle Signal Uses Medium heat to dry large

loads of mixed fabrics and items.

Work clothes,

casual wear,

mixed cottons,

sheets, corduroys

Normal High

Medium

Low

Air

Normal

Less

1:25 Wrinkle Prevent

Cycle Signal

Eco Dry

Uses Medium heat to dry large

loads of mixed fabrics and items.

Normal is the most efcient cycle.

Undergarments,

blouses, lingerie,

performance wear

Delicates High

Medium

Low

Air

Normal

Less

28 Wrinkle Prevent

Cycle Signal Uses Low heat to gently dry

delicate items.

Shirts, blouses,

permanent

press, synthetics,

lightweight items

Wrinkle

Control High

Medium

Low

Air

Normal

Less

35 Wrinkle

Prevent

Cycle Signal

Uses a stepped drying temperature

from Medium to Low for improved

moisture removal and enhanced

fabric care.

Jackets,

comforters,

pillows, jeans

Bulky

Items High

Medium

Low

Air

Normal

Less

52 Wrinkle Prevent

Cycle Signal Use for drying large, bulky items;

do not overll dryer drum. Partway

through the cycle, the signal will

sound for 2 minutes to indicate

when it is time to rearrange items

for optimal drying.

Heavyweight

items such as

towels or heavy

work clothes

Heavy

Duty High

Medium

Low

Air

Normal

Less

57 Wrinkle Prevent

Cycle Signal Offers stepped drying starting with

High heat followed by Medium

heat for enhanced fabric care and

energy savings.

White, sturdy

items Whites High

Medium

Low

Air

Normal

Less

45 Wrinkle Prevent

Cycle Signal Uses High heat to dry large loads of

white, sturdy fabrics and items.

Large loads of

heavyweight

items

Sanitize High More 1:30 Wrinkle Prevent This is a long cycle with high heat,

which has been proven to reduce

household bacteria. This cycle is

not recommended for all fabrics.

Use for large loads of heavyweight

fabrics.

Bright or darkly

colored cottons,

linens, casual and

mixed loads

Colors High

Medium

Low

Air

Normal

Less

53 Wrinkle Prevent

Cycle Signal Uses Medium heat to gently dry

bright or darkly colored items.

Large loads of

cotton towels,

heavyweight

items

Towels High

Medium

Low

Air

Normal

Less

1:00 Wrinkle Prevent

Cycle Signal This is a long cycle with high heat,

which has been proven to reduce

household bacteria. This cycle is

not recommended for all fabrics.

Use for large loads of heavyweight

fabrics.

Load Size Recommendations

For best results, follow the wet load size recommendations noted

for each cycle.

Small load: Fill the dryer drum with 3–4 items, not

more than 1/4 full.

Medium load: Fill the dryer drum up to about 1/2 full.

Large load: Fill the dryer drum up to about 3/4 full. Do

not tightly pack. Items need to tumble freely.

CYCLE GUIDE — TIMED CYCLES

Settings and options shown in bold are default settings for that cycle.

If settings are changed, the new settings will be remembered (except on Quick). If there is a power failure, settings will return to the

default.

Not all features and cycles are available on all models.

Not all settings and options are available on each cycle.

Adjusting drying time on Timed Cycles

When you select a Timed Cycle, the time

appears in the display. Use More Time

and Less Time to increase or decrease

the time in 5-minute increments.

The maximum dry time is 150 minutes.

Selecting the Drying Temperature

A High heat setting may be used for drying heavyweight items

such as towels and work clothes.

A Low to Medium heat setting may be used for drying

mediumweight items such as sheets, blouses, dresses,

underwear, permanent press fabrics, and some knits.

Use a no heat (air) setting for foam, rubber, plastic, or heat-

sensitive fabrics.

Line dry bonded or laminated fabrics.

NOTE: If you have questions about drying temperatures for

various loads, refer to the care label directions.

Items to dry: Cycle: Drying

Temperature: Default

Time: Available

Options: Cycle Details:

Any load

NOTE: Select

Air to dry foam,

rubber, plastic,

or heat-sensitive

fabrics.

Timed Dry High

Medium

Low

Air

40 Wrinkle

Prevent Use to dry items to a damp level for items that

do not require an entire drying cycle. Select a

drying temperature based on the type of fabrics

in your load. If you are unsure of the temperature

to select for a load, select the lower setting

rather than the higher setting.

Small loads and

sportswear Quick High

Medium

Low

Air

15 Wrinkle

Prevent For small loads of 3–4 items.

Load Size Recommendations

For best results, follow the wet load size recommendations noted

for each cycle.

Small load: Fill the dryer drum with 3–4 items, not

more than 1/4 full.

Medium load: Fill the dryer drum up to about 1/2 full.

Large load: Fill the dryer drum up to about 3/4 full. Do

not tightly pack. Items need to tumble freely.

NOTE: Government energy certications for this model were based on the Normal Cycle, Highest Temperature Setting, Normal

Dryness Level, Eco Dry On. The as-shipped defaults were the same as the Government Energy Certication Settings except the

default Temperature Setting of Medium was adjusted to the Highest Temperature Setting. Cycles that are available for post-sale

download may use more energy than the Normal cycle, upon which the energy use rating of this dryer is based.

USING YOUR DRYER

WARNING: To reduce the risk of re, electric shock, or injury to

persons, read the Important Safety Instructions before operating

this appliance.

Clean the lint screen before each load. Pull the lint screen

straight up. Roll lint off the screen with your ngers. Do not rinse

or wash screen to remove lint. Wet lint is hard to remove. Push

the lint screen rmly back into place.

For additional cleaning information, see “Dryer Care.”

Open the door by pulling on the handle. Place laundry in the

dryer. Add a dryer sheet to wet load, if desired. Close the door.

IMPORTANT: Do not tightly pack the dryer. Items need to tumble

freely. Tightly packing can lead to poor drying performance and

may increase wrinkling and tangling.

Touch POWER to turn on the dryer.

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Do not dry anything that has ever had anything

flammable on it (even after washing).

Failure to follow these instructions can result in death,

explosion, or fire.

Clean the lint screen

1. Load the dryer

Touch POWER

WARNING

Fire Hazard

No washer can completely remove oil.

Do not dry anything that has ever had any type of oil on

it (including cooking oils).

Items containing foam, rubber, or plastic must be dried

on a clothesline or by using an Air Cycle.

Failure to follow these instructions can result in death

or fire.

Select desired cycle

Select the desired cycle for your load. See the “Cycle Guide” for

more information about each cycle.

You may adjust different settings, depending

on whether you have selected a Sensor

Cycle or Timed Cycle. See the “Cycle Guide”

for detailed information.

NOTE: Not all options and settings are available with all cycles.

Not all cycles are on all models.

Sensor Cycles:

The temperature may be changed by touching Temp until the

desired dry temperature is lit. Once a cycle has started, the

temperature can be changed during the rst 5–8 minutes of the

cycle.

You can select a different dryness level, depending on your load.

Touch DRYNESS to scroll from Less to More to automatically

adjust the dryness level at which the dryer will shut off. Once

a dryness level is set, it can be changed during the rst 5–8

minutes of the cycle.

Sensor cycles give the best drying in the shortest time. Drying

time varies based on fabric type, load size, and dryness setting.

Drying time is estimated and may change throughout the cycle.

Drying time cannot be changed on Sensor Cycles.

Timed Cycles:

When you select a Timed Cycle, the time appears in the display.

Touch MORE TIME or LESS TIME to increase or decrease the

time in 5-minute increments.

The temperature may be changed by touching Temp until

the desired dry temperature is lit. The temperature cannot be

changed if the temperature is started with Air.

Add additional options such as Wrinkle Prevent and/or Eco Dry

by touching that option. If you will be unable to remove the load

promptly, select Wrinkle Prevent before touching Start/Pause.

NOTE: Not all options and settings are available with all cycles.

To begin the cycle, touch and hold START/PAUSE until the

display counts down “3-2-1” and the dryer starts.

Promptly remove garments after cycle has completed to reduce

wrinkling. If you will be unable to remove the load promptly,

select the Wrinkle Prevent option.

Adjust cycle modiers, if desired

Select any additional options

Touch and hold START/PAUSE

to begin cycle

Remove garments promptly

after cycle is nished

USING THE DRYING RACK

To purchase a drying rack for your dryer, see “Accessories”

for more information. You will need your model and serial

number and the purchase date. Remove and discard any

packing material before use.

Use the drying rack for items that you do not want to

tumble dry, such as sweaters and tennis shoes. When you

use the drying rack, the drum continues to turn, but the

rack remains stationary.

The drying rack is intended for use with the Timed Dry

cycle only. The drying rack cannot be used with Sensor

Cycles.

To use the drying rack:

IMPORTANT: Do not remove the lint screen.

1. Open dryer door.

2. Align the two hooks on the front of the drying rack with

the holes in the dryer door opening and press down

fully into holes. Rest the rear support on the dryer back

ledge.

3. Place wet items on top of the drying rack. Allow space

around items for air to circulate. The drying rack does

not move, but the drum will rotate; be sure to leave

adequate clearance between items and the inside of

the dryer drum. Make sure items do not hang over the

edges or between drying rack grille.

4. Close the door.

5. Select a Timed Dry cycle. Items containing foam,

rubber, or plastic must be dried on a clothesline or by

using the Air setting.

6. When the cycle is selected, the display shows the

default time. You can change the actual time in the

cycle by increasing or decreasing the cycle time.

7. Start the dryer.

NOTE: Check the lint screen and remove any lint

accumulated from items dried on the drying rack after

the cycle is nished.

ADDITIONAL FEATURES DRYER CARE

CLEANING THE DRYER LOCATION

Keep dryer area clear and free from items that would

block the airow for proper dryer operation. This includes

clearing piles of laundry in front of the dryer.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Place dryer at least 18 inches (46 cm) above the

floor for a garage installation.

Failure to do so can result in death, explosion,

or fire.

CLEANING THE DRYER INTERIOR

To clean dryer drum:

1. Use a mild hand dish detergent mixed at a low

concentration with very warm water, and rub with a

soft cloth.

2. Rinse well with a wet sponge or towel.

3. Tumble a load of clean clothes or towels to dry drum

Use a microber cloth and hot water in a spray bottle

to clean the drum and a second microber towel to

dry.

NOTE: Garments that contain unstable dyes, such as

denim blue jeans or brightly colored cotton items, may

discolor the rear of the dryer interior. These stains are

not harmful to your dryer and will not stain future loads

of clothes. Dry unstable dye items inside out to avoid

transfer of dye.

REMOVING ACCUMULATED LINT

From Inside the Dryer Cabinet

Lint should be removed every 2 years, or more often,

depending on dryer usage. Cleaning should be done by a

qualied appliance servicer.

From the Exhaust Vent

Lint should be removed every 2 years, or more often,

depending on dryer usage.

CLEANING THE LINT SCREEN

Every load cleaning

The lint screen is located in the door opening of the dryer.

Clean the lint screen before each load. A screen blocked by

lint can increase drying time.

To clean:

1. Pull the lint screen straight up. Roll lint off the screen

with your ngers. Do not rinse or wash screen to

remove lint. Wet lint is hard to remove.

2. Push the lint screen rmly back into place.

IMPORTANT:

■Do not run the dryer with the lint screen loose,

damaged, blocked, or missing. Doing so can

cause overheating and damage to both the dryer

and fabrics.

■If lint falls off the screen into the dryer during

removal, check the exhaust hood and remove the

lint. See “Venting Requirements” in the Installation

Instructions.

AS-NEEDED CLEANING

Laundry detergent and fabric softener residue can build

up on the lint screen. This buildup can cause longer drying

times for your clothes, or cause the dryer to stop before

your load is completely dry. The screen is probably clogged

if lint falls off while the screen is in the dryer.

Clean the lint screen with a nylon brush every 6 months, or

more frequently, if it becomes clogged due to a residue

buildup.

To wash:

1. Roll lint off the screen with your ngers.

2. Wet both sides of lint screen with hot water.

3. Wet a nylon brush with hot water and liquid detergent.

Scrub lint screen with the brush to remove residue

buildup.

4. Rinse screen with hot water.

5. Thoroughly dry lint screen with a clean towel. Reinstall

screen in dryer.

For direct-wired dryers:

1. Disconnect power.

2. Disconnect wiring.

3. Make sure leveling legs are secure in dryer base.

4. Use tape to secure dryer door.

Reinstalling the Dryer

Follow the Installation Instructions to locate, level, and

connect the dryer.

NON-USE, STORAGE, AND MOVING CARE

Non-Use or Storage Care

Operate your dryer only when you are at home. If you will

be on vacation or not using your dryer for an extended

period of time, you should:

1. Unplug dryer or disconnect power.

2. Clean lint screen. See “Cleaning the Lint Screen.”

Moving Care

For power supply cord-connected dryers:

1. Unplug the power supply cord.

2. Gas models only: Close shut-off valve in gas supply

line.

3. Gas models only: Disconnect gas supply line pipe and

remove ttings attached to dryer pipe.

4. Gas models only: Cap the open gas supply line.

5. Make sure leveling legs are secure in dryer base.

6. Use tape to secure dryer door.

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

TROUBLESHOOTING

First try the solutions suggested here or visit our website at www.amana.com/owners

for assistance and to possibly avoid a service call.

If you experience Possible Causes Solution

Dryer Operation

Dryer will not run Door not closed completely. Make sure the dryer door is closed completely.

Start/Pause touched with ngernail. Touch START/PAUSE with pad of nger.

Household fuse is blown or circuit breaker

has tripped. There may be two household fuses or circuit breakers

for the dryer. Check that both fuses are intact and tight,

or that both circuit breakers have not tripped. Replace

the fuses or reset the circuit breaker. If the problem

continues, call an electrician.

Incorrect power supply. Electric dryers require 240 V power supply. Check with a

qualied electrician.

Wrong type of fuse. Use a time-delay fuse.

Dryer will not turn off Dryer door was opened prior to the end of

the Wrinkle Prevent option. If you open the dryer door prior to the end of the Wrinkle

Prevent option, the dryer will go into the Pause mode.

You will need to touch Power to turn off or touch Start/

Pause to continue the Wrinkle Prevent option.

Dryer will not heat Household fuse is blown or circuit breaker

has tripped. The drum may be turning, but you may not have heat.

Electric dryers use two household fuses or circuit

breakers. Replace the fuses or reset the circuit breaker.

If the problem continues, call an electrician.

Incorrect power supply. Electric dryers require 240 V power supply. Check with a

qualied electrician.

Supply line valve not open. For gas dryers, make sure that the valve on the gas

supply line is open.

Unusual Noise

Thumping noise Dryer hasn’t been used in a while. This is normal. The thumping sound should diminish

after a few minutes of use.

Rattling or vibrating noise A small object caught between the edges

of dryer drum. Check the front and rear edges of the drum for small

objects.

Clean out pockets before laundering.

Dryer isn’t properly leveled. The dryer may vibrate if not properly installed. See the

Installation Instructions. All four dryer feet should be in

rm contact with the oor.

Clothing is balled up in dryer. When balled up, the load will bounce, causing the dryer

to vibrate. Separate the load items and restart the dryer.

Clicking noise Gas valve operating. On gas dryers, you may hear the gas valve clicking as it

opens and closes. This is normal.

Dryer Results

Drying times are too long

and clothes are not getting

dry

Lint screen is clogged with lint. Clean lint screen before each load.

Eco Dry option is on. For optimal dry times, turn off the Eco Dry option.

The exhaust vent or outside exhaust

hood is clogged with lint, restricting air

movement.

Run the dryer for 5–10 minutes. Hold your hand under

the outside exhaust hood to check air movement. If you

do not feel air movement, clean exhaust system of lint or

replace exhaust vent with heavy metal or exible metal

vent. See the Installation Instructions.

The exhaust vent is not the correct length. Check that the exhaust vent is not too long or has too

many turns. Long venting will increase drying times. See

the Installation Instructions.

The exhaust vent diameter is not the

correct size. Use 4" (102 mm) diameter vent material.

TROUBLESHOOTING

First try the solutions suggested here or visit our website at www.amana.com/owners

for assistance and to possibly avoid a service call.

If you experience Possible Causes Solution

Dryer Results (cont.)

Drying times are too long

and clothes are not getting

dry (cont.)

The dryer is not level. Clothes not contacting the moisture sensors during

Sensor cycles. See “Level Dryer” in the Installation

Instructions.

The load is too large and heavy to dry

quickly. Separate the load to tumble freely.

Fabric softener sheets are blocking the

grille. The air outlet grille is just inside the door, behind the lint

screen. Check that it is not blocked by a fabric softener

sheet. Use only one fabric softener sheet, and use it

only once.

The dryer is located in a room with

temperature below 45ºF (7ºC). Proper operation of dryer cycles requires temperatures

above 45ºF (7ºC).

The dryer is located in a closet. Closet doors must have ventilation openings at the top

and bottom of the door. The front of the dryer requires

a minimum of 1” (25 mm) of airspace, and, for most

installations, the rear of the dryer requires 5” (127 mm).

See the Installation Instructions.

Cycle time is too short The load may not be contacting the sensor

strips on Sensor cycles. Level the dryer. See the Installation Instructions. All four

dryer feet should be in rm contact with the oor.

The Sensor cycle is ending early. Change the dryness level setting on Sensor Cycles.

Increasing or decreasing the dryness level will change

the amount of drying time in a cycle.

Lint screen is clogged with lint. Clean lint screen before each load.

Lint on load

Stains on load Improper use of fabric softener. Add dryer fabric softener sheets at the beginning of the

cycle. Fabric softener sheets added to a partially dried

load can stain your garments.

Stains on drum Loose dyes in clothes. Drum stains are caused by dyes in clothing (usually blue

jeans). These will not transfer to other clothing.

Loads are wrinkled The load was not removed from dryer at

the end of the cycle. NOTE: Refer to garment care label instructions. Dry-

clean-only garments are not recommended.

The dryer was tightly packed. Dry smaller loads that can tumble freely. Results may

also vary depending on fabric type.

Odors Recent painting, staining, or varnishing in

the area where your dryer is located. Ventilate the area. When the odors or fumes are gone

from the area, rewash and dry the clothing.

The electric dryer is being used for the rst

time. The new electric heating element may have an odor. The

odor will be gone after the rst cycle.

Load too hot Load removed before cooldown portion of

cycle complete. Allow the dryer to complete the cooldown portion of the

cycle before removing the load.

Using Timed Dry cycle with a high

temperature setting. Select a Sensor cycle with a lower heat setting to avoid

overdrying the load.

TROUBLESHOOTING

First try the solutions suggested here or visit our website at www.amana.com/owners

for assistance and to possibly avoid a service call.

If you experience Possible Causes Solution

Dryer Displaying Code Message or Indicator Is Lit

“PF” (power failure) The drying cycle has been interrupted by a

power failure. Touch and hold START/PAUSE to restart the dryer cycle

or touch POWER to clear the display.

“L2” Diagnostic Code (low

or no line voltage condition) The load is too large and heavy to dry

quickly. The dryer will continue to run when this diagnostic code

is present. Touch any pad to clear the code from the

display and return to the estimated time remaining.

NOTE: This error will only show during the initial

installation.

Try the following:

■Check to see if a household fuse has blown or

circuit breaker has tripped. Electric dryers use two

household fuses or breakers. Replace the fuse or

reset the circuit breaker.

■Conrm that the power cord is properly installed.

Refer to the Installation Instructions for details.

■Select a Timed Dry heated cycle, and restart the

dryer.

If the message persists, consult a qualied electrician.

“F# E#” (F1 E1, F3 E1, etc.)

variable service codes The dryer is in need of service. If a code beginning with an “F” appears in the display,

alternating between F# and E#, the dryer control has

detected a problem that requires service. Call for

service.

Check Vent indicator is lit The lint screen or vent is clogged; the

vent is crushed or kinked or has too many

turns.

The dryer will continue to run when this indicator is lit.

Try the following:

■Clean lint screen.

■Check to see if the vent run from the dryer to the

wall is crushed or kinked.

■Conrm that the vent run from the dryer to the wall

is free of lint and debris.

■Conrm that the exterior vent exhaust hood is free

of lint and debris.

■Conrm that your vent system falls within the

recommended run length and number of elbows for

the type of vent you are using. Refer to “Plan Vent

System” in the Installation Instructions for details.

■Select a Timed Dry heated cycle, and restart the

dryer.

■If the indicator remains lit, have your entire home

venting run cleaned.

“Loc” The Control Lock is enabled. Touch and hold CONTROL LOCK for 3 seconds to

unlock the controls of the dryer. During this time, the

LED Display will count down “3-2-1.” When the Control

Lock is disabled, the LED Display will clear.

WHIRLPOOL CORPORATION LAUNDRY WARRANTY

ITEMS EXCLUDED FROM WARRANTY

This limited warranty does not cover:

LIMITED WARRANTY

For one year from the date of purchase, when this major appliance is installed, operated, and maintained according to instructions

attached to or furnished with the product, Amana, Admiral, Estate, Inglis, or Roper brands of Whirlpool Corporation or Whirlpool

workmanship that existed when this major appliance was purchased.

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED

HEREIN. Service must be provided by a company designated by Whirlpool to service Amana, Admiral, Estate, Inglis, or Roper brand

appliances. This limited warranty is valid only in the United States or Canada and applies only when the major appliance is used in

the country in which it was purchased. This limited warranty is effective from the date of original consumer purchase. Proof of original

purchase date is required to obtain service under this limited warranty.

The cost of repair or replacement under these excluded circumstances shall be borne by the customer.

DISCLAIMER OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS

FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and

province.

1. Replacement parts or repair labor if this major appliance is used for other than normal, single-family household use or when it is

used in a manner that is inconsistent to published user or operator instructions and/or installation instructions.

2. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or

repair house fuses, or to correct house wiring or plumbing.

3. coverage.

4. accordance with electrical or plumbing codes, or use of products not approved by Whirlpool.

5. results from defects in materials or workmanship and is reported to Whirlpool within 30 days from the date of purchase.

6. Pick up and delivery. This major appliance is intended to be repaired in your home.

8. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an

authorized company designated by Whirlpool to service Amana, Admiral, Estate, Inglis, or Roper brands is not available.

9. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance

with Whirlpool’s published installation instructions.

10. Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered, or

cannot be easily determined.

LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.

WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow

the exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This

1/12

call: 7776 -708- 008 for Amana, Admiral, Estate, Inglis, or Roper brand products.

If outside the 50 United States and Canada, contact your authorized Whirlpool, Amana, Admiral, Estate, Inglis, or Roper dealer to

determine if another warranty applies.

the problem after checking “Troubleshooting,” additional help can be found by checking the “Assistance or Service” section or by

calling the following numbers for assistance: In the U.S.A., call 800-843-0304 for Amana brand products; 800-688-9920 for Admiral

brand products; 800-253-1301 for Estate brand products, or 800-447-6737 for Roper brand products. For assistance In Canada,

DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY

Whirlpool makes no representations about the quality, durability, or need for service or repair of this major appliance other than the

representations contained in this Warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes

with this major appliance, you should ask Whirlpool or your retailer about buying an extended warranty.

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation

date for in-warranty service.

Write down the following information about your major appliance

to better help you obtain assistance or service if you ever need

it. You will need to know your complete model number and serial

number label located on the product.

Dealer name _____________________________________________

Address __________________________________________________

Phone number ____________________________________________

Model number ____________________________________________

Serial number ____________________________________________

Purchase date ____________________________________________

Risque possible de décès ou de blessure grave si vous ne

suivez pas immédiatement les instructions.

Risque possible de décès ou de blessure grave si vous

ne suivez pas les instructions.

Tous les messages de sécurité vous diront quel est le danger potentiel et vous disent comment réduire le risque de blessure et

ce qui peut se produire en cas de non-respect des instructions.

Votre sécurité et celle des autres est très importante.

Nous donnons de nombreux messages de sécurité importants dans ce manuel et sur votre appareil ménager. Assurez-vous de

toujours lire tous les messages de sécurité et de vous y conformer.

AVERTISSEMENT

DANGER

Voici le symbole d’alerte de sécurité.

Ce symbole d’alerte de sécurité vous signale les dangers potentiels de décès et de blessures graves à vous

et à d’autres.

Tous les messages de sécurité suivront le symbole d’alerte de sécurité et le mot “DANGER” ou

“AVERTISSEMENT”. Ces mots signifient :

SÉCURITÉ DE LA SÉCHEUSE

Dans l’État du Massachusetts, les instructions d’installation suivantes sont applicables :

Les travaux d’installation et réparation doivent être exécutés par un plombier ou tuyauteur qualifié ou licencié, ou par le

personnel qualifié d’une entreprise licenciée par l’État du Massachusetts.

Remplacer par des dispositifs de fermeture acceptables : Les robinets de gaz et robinets à bille installés pour l'utilisation

devraient être indiqués.

Si un conduit de raccordement flexible est utilisé, sa longueur ne doit pas dépasser 4 pi (121,9 cm).

AVERTISSEMENT :

RISQUE D'INCENDIE OU D'EXPLOSION

Le non-respect des avertissements de sécurité peut causer des dommages à la propriété,

des blessures graves, voire la mort.

–Ne pas entreposer ou utiliser de l’essence ou d’autres vapeurs ou liquidesinflammables

à proximité de cet appareil ou de tout autre appareil électroménager.

–QUE FAIRE DANS LE CAS D’UNE ODEUR DE GAZ :

•

Ne pas tenter d’allumer un appareil.

•

Ne pas toucher à un commutateur électrique; ne pas utiliser le téléphone se trouvant

sur les lieux.

•

Évacuer tous les gens de la pièce, de l’édifice ou du quartier.

•

Appeler immédiatement le fournisseur de gaz d’un téléphone voisin. Suivre ses

instructions.

•

À défaut de joindre votre fournisseur de gaz, appeler les pompiers.

–L’installation et l’entretien doivent être effectués par un installateur qualifié, uneagence

de service ou le fournisseur de gaz.

IMPORTANT : L'installation du gaz doit se conformer aux codes locaux, ou en l'absence de codes locaux, au code d'installation

du gaz naturel ou du propane, CSA B149.1.

La sécheuse doit être électriquement reliée à la terre conformément aux codes locaux, ou en l'absence de codes locaux, au Code

canadien de l'électricité, partie 1, CSA C22.1.

ACCESSOIRES

Accessoires conçus pour votre appareil :

Personnalisez votre nouvelle laveuse et sécheuse grâce

aux authentiques accessoires Whirlpool suivants. Pour

plus d’informations sur les options et sur les possibilités de

commande, appeler au 1-800-442-9991 ou consulter

www.amana.com/help.

Au Canada, composer le 1-800-807-6777 ou consulter :

www.amana.com/help.

Piédestal de 15"

Les piédestaux aux coloris assortis

surélèvent la laveuse et la sécheuse

pour les amener à une hauteur

d’utilisation plus confortable. Le

grand tiroir offre une capacité de

rangement pratique.

Ensemble de superposition

Si l’espace disponible est restreint,

l’ensemble de superposition permet à la

sécheuse d’être installée par dessus la

laveuse.

Grille de séchage

La grille de séchage fournit une

surface de séchage stationnaire

pour les articles tels que les

chandails et les chaussures de

tennis. Voir la section

“Caractéristiques

supplémentaires” pour

l’information supplémentaire..

PIECES AGRÉÉS PAR LE FABRICANT

ACCESSOIRES D’INSTALLATION

ET D’ENTRETIEN

PIECES AGRÉÉS PAR LE FABRICANT, ces mots

désignent des pieces de qualité et des accessoires

conçus spécialement pour votre appareil. Une

ingénierie qui a fait ses preuves, pour répondre

a nos normes de qualité les plus strictes.

La page charge ...

Amana YNED5800HW0 Mode d'emploi

Marque: Amana

Modèle: YNED5800HW0

Catégorie: Sèche-linge

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Amana YNED5800HW0 User guide

Documents connexes

Amana NED5800HW Mode d'emploi

Amana YNED5800HW0 Mode d'emploi

Amana YNED5800HW0 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents