Whirlpool YWED8500BC0 Le manuel du propriétaire

Marque: Whirlpool

Modèle: YWED8500BC0

Catégorie: Sèche-linge électriques

Taper: Le manuel du propriétaire

Whir

CABRIO ®

ELECTRONIC DRYER

USE AND CARE GUIDE

St_CHEUSE

I_LECTRONIQUE CABRIO ®

GUIDE D'UTILISATION

ET D'ENTRETIEN

Table of Contents

DRYER SAFETY ............................................................ 2

CHECK YOUR VENT SYSTEM

FOR GOOD AiR FLOW ................................................. 4

CONTROL PANEL AND FEATURES ............................ 5

CYCLE GUIDE ............................................................... 6

USING YOUR DRYER ................................................... 8

ADDiTiONAL FEATURES ................................................10

DRYERCARE....................................................................... 11

TROUBLESHOOTING ...................................................... 13

WARRANTY ........................................................................16

ASSISTANCE OR SERVICE ...........................Back Cover

Table des mati_res

S¢:CURiTF: DE LA SECHEUSE ................................... 17

VC:RiFiCATiON D'UNE CiRCULATiON D'AIR

ADC:QUATE POUR LE SYSTi_ME D'C:VACUATiON...19

TABLEAU DE COMMANDE

ET CARACTi_RiSTIQUES .......................................... 20

GUIDE DES PROGRAMMES ...................................... 21

UTiLiSATiON DE LA S¢:CHEUSE ............................... 25

CARACTC:RiSTIQUES SUPPLC:MENTAiRES ............. 27

ENTRETiEN DE LA S¢:CHEUSE .................................... 28

DF:PANNAGE ...................................................................... 31

GARANTIE ..........................................................................35

ASSISTANCE OU SERVICE ..............Couverture arri_re

If you have any problems or questions, visit us at www.whiripool.com

Pour tout probleme ou question, consulter www.whirlpool.ca

Para obtener acceso al "Manual de usoy cuidado" enespaffol, o para

obtener informaci6n adicional acerca de su producto, visite: www.whiripooi.com.

W10562333B

W10562337B - SP

DRYER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

WARNING - ...i.. ofFi,o..

- Clothes dryer installation must be performed by a qualified installer.

- install the clothes dryer according to the manufacturer's instructions and local codes.

- Do not install a clothes dryer with flexible plastic venting materials or flexible metal

(foil type) duct, if flexible metal duct is installed, it must be of a specific type identified

by the appliance manufacturer as suitable for use with clothes dryers. Flexible venting

materials are known to collapse, be easily crushed, and trap lint. These conditions will

obstruct clothes dryer airflow and increase the risk of fire.

- To reduce the risk of severe injury or death, follow all installation instructions.

- Save these instructions.

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

in the State of Massachusetts, the following installation instructions apply:

I Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by

the State of Massachusetts.

I If using a ball valve, it shall be a T-handle type.

m A flexible gas connector, when used, must not exceed 3 feet.

iMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas

Code, ANSI Z223.1/NFPA 54 or the Canadian Natural Gas and Propane Installation Code, CSA B149.1.

The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National

Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1.

WARNING: For your safety, the information in this manual must be followed to minimize 1

the risk of fire or explosion, or to prevent property damage, personal injury, or death, j

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

- WHAT TO DO iF YOU SMELL GAS:

o Do not try to light any appliance.

®Do not touch any electrical switch; do not use any phone in your building.

®Clear the room, building, or area of all occupants.

• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

= if you cannot reach your gas supplier, carl the fire department.

- Installation and service must be performed by a qualified installer, service agency, or

the gas supplier.

WARNING: Gas leaks cannot always be detected by smell.

Gas suppliers recommend that you use a gas detector approved by UL or CSA.

For more information, contact your gas supplier.

If a gas leak is detected, follow the "What to do if you smell gas" instructions.

iMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions,

including the following:

[] Read all instructions before using the dryer.

[] Do not place items exposed to cooking oils in your dryer.

items contaminated with cooking oils may contribute to

a chemical reaction that could cause a load to catch fire.

[] Do not dry articles that have been previously cleaned in,

washed in, soaked in, or spotted with gasoline, dry=

cleaning solvents, or other flammable or explosive

substances as they give off vapors that could ignite or

explode.

[] Do not allow children to play on or in the dryer. Close

supervision of children is necessary when the dryer is

used near children.

[] Before the dryer isremoved from service or discarded,

remove the door to the drying compartment.

[] Do not reach into the dryer if the drum is moving.

[] Do not install or store the dryer where it will be exposed

to the weather.

[] Do not tamper with controls.

[] Do not repair or replace any part of the dryer or attempt

any servicing unless specifically recommended in this

Use and Care Guide or in published user=repair

instructions that you understand and have the skills to

carry out.

[] Do not use fabric softeners or products to eliminate static

unless recommended by the manufacturer of the fabric

softener or product.

[] Do not use heat to dry articles containing foam rubber or

similarly textured rubberqike materials.

[] Clean lint screen before or after each load.

[] Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint, dust,

and dirt.

[] The interior of the dryer and exhaust vent should be

cleaned periodically by qualified service personnel.

[] See "Electrical Requirements" located in the installation

instructions for grounding instructions.

SAVE THESE INSTRUCTIONS

iMPORTANT: When discarding or storing your old clothes dryer, remove the door.

CHECK YOUR VENT SYSTEM FOR GOOD AIR FLOW

Fire Hazard

Use a heavy metal vent,

Do not use a plastic vent.

Do not use a metal foil vent,

Failure to follow these instructions can result in death

or fire.

Good air flow

Along with heat, dryers require good air flow to efficiently

dry laundry. Proper venting will reduce your drying times

and improve your energy savings. See Installation

Instructions.

The venting system attached to the dryer plays a big role

in good air flow.

Service calls caused by improper venting are not covered

by the warranty and will be paid by the customer, regardless

of who installed the dryer.

Maintain good air flow by:

[] Cleaning your lint screen before each load.

[] Replace plastic or foil vent material

with 4" (102 mm) diameter heavy, rigid

vent material.

[] Use the shortest length of vent possible.

[] Use no more than four 90° elbows in a vent system;

each bend and curve reduces air flow.

[]

Remove lint and debris from the exhaust hood.

Remove lint from the entire length of the vent system

at least every 2 years. When cleaning is complete, be

sure to follow the "Installation Instructions" supplied

with your dryer for final product check.

Clear away items from in front of the dryer.

Use Eco Cycles for better fabric care and energy savings

Use the Eco Cycles to provide the most energy savings and enhanced fabric care from the dryer. During Eco Cycles, drying air

temperature and moisture level are sensed in the load. This sensing occurs throughout the drying cycle and the dryer shuts off

when the load reaches the selected dryness. Use the NORMAL dryness level to provide optimal energy savings.

With Timed Dry Cycles, the dryer runs the amount of time set and sometimes results in shrinkage, wrinkling, and static due to

over-drying. Use Timed Dry Cycles for the occasional damp load that needs a little more drying time or when using the drying

rack.

Tips for getting the best performance from your steam dryer

[] Results may vary depending on fabric. 100% cotton [] The Enhanced Touch Up cycle is best for reducing odors

garments with wrinkle-free finish may yield better results and light wrinkles in small to medium=sized loads of dry

than those without. 100% cotton items may require garments. For the Enhanced Touch Up cycle, dry time

additional touching up after the Steam Cycle. automatically adjusts as load size is sensed. Cycle run

[] Use of fabric softener sheet is not recommended with time cannot be manually adjusted.

Steam Cycles. It may cause temporary staining on clothes. [] The Quick Refresh (on some models) cycle is best for

[] It is not recommended to use Steam Cycles for items that reducing wrinkles and odors in dry garments, including

have been starched. Wash any starched or new garments loads left in the dryer. For, Quick Refresh time is selectable

prior to using a Steam Cycle. in five minute increments based on the load to be refreshed.

CONTROL PANEL AND FEATURES

SHEETS

Whyool

Cobrio ACl VE WEAR

.])[atinum

DELICATE

Do._m START

Check

)ryness Temp DampDry Wrinkle Vent

L /eve SEgnal Shield

Not all features and cycles are available on all models.

O POWER BUTTON

Press to turn the dryer on and off. Press again

to stop/cancel a cycle at any time.

CYCLE CONTROL KNOB

Use your dryer's cycle control knob to select available

cycles on your dryer. Turn the knob to select a cycle

for your laundry load. See "Cycle Guide" for detailed

descriptions of cycles.

O EST. TIME REMAINING DISPLAY

When you select a cycle, its default settings will light

up and the Estimated Time Remaining (for Automatic

Cycles) or actual time remaining (for Manual Cycles)

will be displayed.

DONE/SENSING DISPLAY

Done

This will indicate that the selected cycle has ended

and the load may be removed from the dryer. If the

Wrinkle Shield option has been selected, the dryer

may continue to tumble the load, even if the DONE

indicator is lit.

Sensing

At the beginning of an Automatic Cycle, the sensing

light illuminates as the dryer senses the load size and

adjusts for the appropriate dry time for that load. This

indicator will not light during Timed Cycles or with

options such as Wrinkle Shield TM.

ECO MONITOR

Your dryer is specially designed to conserve energy. Each

cycle, along with selected options, will result in different

energy usage, which will be displayed on the Eco Monitor

bar, allowing you to choose the best energy usage for each

load.

START/PAUSE BUTTON

Press to start a cycle, or press once while a cycle is in

process to pause it.

CYCLE OPTIONS

Use these buttons to select available options for your dryer.

Not all cycles and options are available on all models.

Eco Boost (on some models)

Press to activate Eco Boost option on select Automatic

cycles. The Eco Boost option allows you to increase

your energy savings with minimal impact on cycle dry

times.

NOTE: Selecting the Eco Boost option adds 5 minutes

to the default cycle time.

Static Reduce (on some models)

Press to add the Static Reduce option to select cycles

(see Cycle Guide). The dryer will automatically tumble

and spray to introduce a small amount of moisture

into the load to help reduce static. This option adds

approximately 8 minutes to the total cycle time.

Damp Dry Signal

When selected, a signal will sound during the drying

cycle when the load is damp but not completely dry.

This will allow you to take clothes out of the load that

do not need to dry completely. This option is available

on Heavy Duty, Normal, Sheets, Active Wear, Towels,

Casual, Jeans, and Delicate cycles. It is a default

option for the Bulky Items cycle.

Wrinkle Shield'M/Wrinkle Shield TM with Steam

(on some models)

If you will be unable to remove a load immediately,

press WRINKLE SHIELD 'Mto add up to 140 minutes of

periodic tumbling to help reduce wrinkling. On models

with Wrinkle Shield '" with Steam, a short steam cycle

is added after 60 minutes to help smooth out wrinkles.

Cycle Signal

Use this button to turn the signal indicating the end of

a drying cycle on or off, or to adjust the volume of the

signal.

Check Vent indicator Light

The Check Vent indicator light will come on if a

blocked vent or low airflow issue is detected. For

more information on maintaining good airflow, see

"Check Your Vent System for Good Airflow".

CYCLE MODIFIERS

Use these buttons to select available modifiers for your

cycles. Not all cycles and modifiers are available on all

models.

Dryness Level

You may adjust the Dryness Level on Automatic

Cycles, if desired.

NOTE: The Dryness Level modifier is for use with

Automatic Cycles only. Not available on the Sanitize

cycle.

Temp

When using Manual Cycles only, you may select

a dry temperature based on the type of load you

are drying. Use the warmest setting safe for the

garments in the load. Follow garment label instructions.

NOTE: Automatic Cycles use a preset temperature

that is not adjustable.

CYCLE GUIDE- AUTOMATIC CYCLES

Settings and options shown in bold are default settings for that cycle. Not all features and cycles are available on all models.

Not all settings and options are available on each cycle. Default cycle times are estimated in minutes.

Use Automatic Cycles for better fabric care and energy savings

The dryer senses moisture in the load or air temperature and shuts off when the load reaches the selected dryness level.

Use the NORMAL dryness level to provide optimal energy savings. Use Automatic/Eco cycles on their default settings for optimal

energy savings.

Towels, bedding,

children's clothing

Heavyweight items

such as towels or

heavy work clothes

Jeans and denims

Large loads of cotton

towels, heavyweight

items

Work clothes, casual

wear, mixed cottons,

sheets, corduroys

Shirts, blouses,

permanent press,

synthetics,

lightweight items

Jackets, comforters,

fiberfill pillows

Sheets, lightweight

linens

Performance fabrics,

exercise wear

Undergarments,

blouses, lingerie,

performance wear

Sanitize

Heavy

Duty*

Jeans*

Towels*

Normal*

Perm

press/

Casual*

Bulky

Items*

Sheets*

Active

Wear*

Delicate*

High

Medium

High

Medium

Low

Medium

Extra Low

Normal

Less

Damp

Normal

Less

Damp

Normal

Less

Damp

Normal

Less

Damp

Normal

Less

Damp

Normal

Less

Damp

Normal

Less

Damp

Normal

Less

Damp

Normal

Less

Damp

Wrinkle Shield t

Damp Dry

Signal

Wrinkle Shield t

Static Reduce

Eco Boost

Damp Dry

Signal

Wrinkle Shield t

Static Reduce

Eco Boost

Damp Dry

Signal

Wrinkle Shield t

Static Reduce

Eco Boost

Damp Dry

Signal

Wrinkle Shield t

Static Reduce

Eco Boost

Damp Dry

Signal

Wrinkle

Shield t

Static Reduce

Eco Boost

Damp Dry

Signal

Wrinkle Shield t

Eco Boost

Damp Dry

Signal

Wrinkle Shield t

Static Reduce

Eco Boost

Damp Dry

Signal

Wrinkle Shield t

Static Reduce

Eco Boost

Damp Dry

Signal

Wrinkle Shield t

Static Reduce

Eco Boost

Extended high-heat drying cycle

intended to help sanitize items such

as bedding, towels, and baby wear.

This cycle is not recommended for all

fabrics. For best results, run cycle to

completion, do not interrupt.

Offers stepped drying starting with

High heat, followed by Medium heat

for enhanced fabric care and energy

savings.

Stepped drying uses High heat initially,followed by Medium heat to drive

moisture from jeans and denims.

This is a long cycle with High heat tothoroughly dry towels. This cycle is not

recommended for all fabrics. Use for

large loads of heavyweight fabrics such

as cotton towels.

Uses Medium heat to dry large loads ofmixed fabrics and items. Normal is the

preferred energy cycle.

Uses a stepped drying temperature

from Medium heat to Low heat for

improved moisture removal and

enhanced fabric care.

Use for drying large, bulky items; do not

overfill dryer drum. Partway through the

cycle, the signal will sound to indicate

when it is time to rearrange items for

optimal drying.

Uses Medium heat to dry sheets andlightweight linens.

Use for drying active wear andperformance fabrics that require

special care.

Uses Extra Low heat to gently drydelicate items.

Or Wrinkle Shield ''_with Steam (on some models). Wrinkle Shield TM with Steam is available only with High and Medium Temp settings.

* Automatic/Eco cycle

Load Size Recommendations

For best results, follow the wet load size recommendations noted for

each cycle.

_ Medium load: Fill the dryer drum up to about 1/2 full.

Small load: Fill the dryer drum with 3-4 items,not more than 1/4 full.

Large load: Fill the dryer drum up to about 3/4 full.

Do not overload. Items need to tumble freely.

CYCLE GUIDE -- MANUAL CYCLES

Settings and options shown in bold are default settings for that cycle. Not all features and cycles are available on all models.

Not all settings and options are available on each cycle. Default cycle times are estimated in minutes.

Time Adjust

Adjusting drying time on Timed Dry Cycles

_,,_,R_m_r,i_ When you select a Timed Dry Cycle,

the default time appears in the display.

Use the Time Adjust buttons to increase

or decrease the time in 1 minute

increments. Press and hold to change

the time in 5 minute increments.

The maximum dry time is 90 minutes.

Selecting the Temp

A High heat setting may be used for drying heavyweight

items such as towels and work clothes.

A Low to Medium heat setting may be used for drying

medium-weight items such as sheets, blouses, dresses,

underwear, permanent press fabrics, and some knits.

Use a no-heat (Air Only) setting for foam, rubber, plastic,

or heat-sensitive fabrics.

Line dry bonded or laminated fabrics.

NOTE: If you have questions about drying temperatures

for various loads, refer to the care label directions.

Small loads and

sportswear

Any load

NOTE: Select Air

Only to dry foam,

rubber, plastic, or

heat-sensitive fabrics

Small to medium

loads

Quick Dry

Timed Dry

Touch

Up (for

non-steam

models)

High

Medium

Low

Extra Low

Air Only

High

Medium

Low

Extra Low

Air Only

High

Medium

Low

Extra Low

Air Only

Wrinkle Shield t

For small loads of 3-4 items

Use to dry items to a damp level for items thatdo not require an entire drying cycle. Select

a drying temperature based on the type of

fabrics in your load. If you are unsure of the

temperature to select for a load, select the

lower setting rather than the higher setting.

Use this setting to help smooth out wrinkles

from such items as garments packed in a

suitcase or garments wrinkled from being left

in the dryer.

Or Wrinkle Shield '_ with Steam (on some models). Wrinkle Shield TM with Steam is available only with High and Medium Temp settings.

CYCLE GUIDE- STEAM CYCLES

Settings and options shown in bold are default settings for that cycle.

Not all settings and options are available on each cycle.

Steam cycles are designed for use with dry loads to loosen wrinkles, reduce odors, and refresh fabrics.

Mixed Loads

Shirts, blouses, and

slacks

Enhanced

Touch Up

Quick

Refresh

(on some

models)

High

Medium

High

Wrinkle Shield t

Static Reduce

Wrinkle Shield t

Static Reduce

Extended high-heat drying cycle intended to

help sanitize items such as bedding, towels,

and baby wear. This cycle is not recommended

for all fabrics. For best results, run cycle to

completion, do not interrupt.

Offers stepped drying starting with High heat,

followed by Medium heat for enhanced fabric

care and energy savings.

Or Wrinkle Shield _ with Steam (on some models). Wrinkle Shield TM with Steam is available only with High and Medium Temp settings.

Load Size Recommendations

For best results, follow the load size recommendations noted for

each cycle.

Q mall load: Fill the dryer drum with 3-4 items,

not more than 1/4 full.

_ IVledium load: Fill the dryer drum up to about 1/2 full.

Large load: Fill the dryer drum up to about 3/4 full.

Do not overload. Items need to tumble freely.

USING YOUR DRYER

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Do not dry anything that has ever had anything

flammable on it (even after washing).

Failure to follow these instructions can result in death,

explosion, or fire.

WARNING: To reduce the risk of fire, electric shock, or injury to

persons, read the IMPORTANT SAFETY INSTRUCTIONS before

operating this appliance.

1. Clean the lint screen

Clean the lint screen before each load. Pull the lint screen

straight up. Roll lint off the screen with your fingers. Do not rinse

or wash screen to remove lint. Wet lint is hard to remove. Push

the lint screen firmly back into place.

For additional cleaning information, see "Dryer Care".

Fire Hazard

No washer can completely remove oil.

Do not dry anything that has ever had any type of oil on

it (including cooking oils).

items containing foam, rubber, or plastic must be dried

on a clothesline or by using an Air Cycle.

Failure to follow these instructions can result in death

or fire,

3. POWER

POWER

Press the POWER button to turn on the dryer.

4. Select the desired cycle

f_""_'_ _ NORMAL

CASUAL .......................... TOWELS

BULKY ITE ...... EANS

SHEETS i_ / U _/ HEAVY DUTY

ACTIVEWEAR t_ __1_I SANITIZE

l l_ ____ /_utomatk: _yd_s

DELICATE ?_.. /#: ............ _,....

ENHANCE[_) ]'T?-_':_ QUICK

TOUCH UP QUICK DRY

REFfi SH

Select the desired cycle for your load. See the "Cycle Guide"

for more information about each cycle.

NOTE: Not all cycles are available on all models.

Open the door by pulling on the handle. Place laundry in the

dryer. Add a dryer sheet to wet load, if desired. Close the door.

IMPORTANT: Do not overload the dryer. Items need to tumble

freely. Overloading can lead to poor drying performance and

may increase wrinkling and tangling.

5. Adjust cycle modifiers, if desired

High

_More _ Medium

IN .... I ILow

I Less ! Extra Low

WDamp _ Air Only

Dryness Temp

Level Manuel

Automatic Cycles Only

Cycles Only

You may adjust different settings, depending on whether you

have selected an Automatic Cycle, or Manual Cycle. See the

"Cycle Guide" for detailed information.

NOTE: Not all options and settings are available with all cycles.

Not all cycles are on all models.

Automatic Cycles:

You can select a different Dryness Level, depending on your

load, by pressing the Dryness Level button. Selecting More,

Normal, Less, or Damp automatically adjusts the Dryness Level

at which the dryer will shut off. Once the Dryness Level is set,

it cannot be changed without stopping the cycle.

Sensor cycles give the best drying in the shortest time. Drying

time varies based on fabric type, load size, and dryness setting.

Timed Cycles:

When you select a Timed Cycle, the default

time appears in the display. Use the Time

Adjust buttons to increase or decrease the

time in 1 minute increments. Press and hold

to change the time in 5 minute increments.

The default temperature may be changed by

pressing the Temp button until the desired

drying temperature lights up.

Est, Time Rema ning

Time Adjust

Steam Cycles:

Quick Refresh with Steam:

Reduces odors and light wrinkles from small to medium-sized

loads of dry items. Use the Time Adjust buttons to select the

time appropriate for the load you want to dry. Cycle time is

adjustable in 5 minute increments.

Enhanced Touch Up with Steam:

This cycle is best for reducing wrinkles and odors from dry

garments. Dry time will automatically adjust when the load

size is sensed. Temperature is selectable.

6. Select any additional options

EcoBoost

Static

Reduce

Damp Dry

Signal

Cycle Signal

_ Steam \ Loud

) Soft

No Steam / Off

Wdnkle

Shield

Add additional options such as Eco Boost, Static Reduce,

and Wrinkle Shield TM (with or without Steam) by pressing

the button for that option.

NOTE: Not all options and settings are available with all cycles.

7. Press START/PAUSE to begin cycle

start

pause

Press and hold the START/PAUSE button to begin the cycle.

8. Remove garments promptly

after cycle is finished

I Steam

No Steam

Wrinkle

Shield

Promptly remove garments after cycle has completed to

reduce wrinkling. If you will be unable to remove the load

promptly, select the WRINKLE SHIELD TM option (with or without

Steam) before pressing START/PAUSE.

'Changing the Automatic Cycle settings

to increase drying time

If all your loads on all Automatic Cycles are consistently

not as dry as you would like or are too dry, you may change

the default settings to increase or decrease the default

Dryness Level.

The sensor drying settings on Automatic Cycles can be

adjusted to adapt to different installations, environmental

conditions or personal preference. This change is retained

and will affect all of your Automatic Cycles, not just the

current cycle/load.

There are 5 drying settings, they will appear inthe time

display:

01 Factory preset dryness level.

02 Slightly drier clothes, 15% more drying time.

03 Much drier clothes, 30% more drying time.

04 Much damper clothes, 30% less drying time.

05 Slightly damper clothes, 15% less drying time.

To change the drying settings:

NOTE: The settings cannot be changed while the dryer

is running or paused. The dryer must be in standby mode

(the Power button is off) to adjust the default settings.

1. Before starting a cycle, press and hold the DRYNESS

LEVEL button for 6 seconds.

2. Press the DRYNESS LEVEL button to select the dryness

level shown in the time display: 01,02, 03, 04, or 05.

3. Press START/PAUSE to save the new Dryness Level

setting.

ADDITIONAL FEATURES

USING THE DRYING RACK

To obtain a drying rack for your dryer, follow the instructions

included in your dryer drum. Remove and discard any

packing material before use.

Use the Drying Rack for items that you do not want to

tumble dry, such as sweaters and tennis shoes. When you

use the drying rack, the drum continues to turn, but the rack

remains stationary.

The drying rack is intended for use with the Timed Dry

Cycles only. The drying rack cannot be used with any

Automatic Cycles.

To use the drying rack:

IMPORTANT: Do not remove the lint screen.

1. Open dryer door.

2. Align the two hooks on the front of the drying rack with

the holes in the dryer door opening and press down fully

into holes. Rest the rear support on the dryer back ledge.

3. Place wet items on top of the drying rack. Allow space

around items for air to circulate. The drying rack does

not move, but the drum will rotate; be sure to leave

adequate clearance between items and the inside

of the dryer drum. Make sure items do not hang over

the edges or between drying rack grille.

4. Close the door.

5. Select Timed Dry. Select the Air Only, Low or Extra Low

Temp setting. Items containing foam, rubber, or plastic

must be dried on a clothesline or by using the Air Only

Temp setting.

6. When the cycle is selected, the Estimated Time

Remaining display shows the default time. You can

change the actual time in the cycle by increasing or

decreasing the cycle time.

7. Press START/PAUSE.

NOTE: Check the lint screen and remove any lint

accumulated from items dried on the drying rack

after the cycle is finished.

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

CHANGING THE DRUM LIGHT

The dryer light automatically turns on inside the dryer drum

when you open the door.

To change the drum light:

1. Unplug dryer or disconnect power.

2. Open the dryer door. Locate the light bulb cover on the

back wall of the dryer. Remove the screw located in the

lower right corner of the cover. Remove the cover.

3. Turn bulb counterclockwise. Replace the bulb with

a lO-watt appliance bulb only. Replace the cover and

secure with the screw.

4. Plug in dryer or reconnect power.

DRYER CARE

I LEANING THE DRYER LOCATION I

Keep dryer area clear and free from items that would

block the air flow for proper dryer operation. This includes

clearing piles of laundry in front of the dryer.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Place dryer at least 18 inches (460 ram) above the floor

for a garage installation.

Failure to do so can result in death, explosion, or fire.

CLEANING THE DRYER iNTERiOR

To clean dryer drum

1. Use a mild hand dish detergent mixed at a low

concentration with very warm water, and rub with

a soft cloth.

2. Rinse well with a wet sponge or towel.

3. Tumble a load of clean clothes or towels to dry drum

Use a microfiber cloth and hot water in a spray bottle

to clean the drum and a second microfiber towel to dry.

NOTE: Garments that contain unstable dyes, such as

denim blue jeans or brightly colored cotton items, may

discolor the rear of the dryer interior. These stains are

not harmful to your dryer and will not stain future loads

of clothes. Dry unstable dye items inside out to avoid

transfer of dye.

REMOVING ACCUMULATED LiNT

From inside the dryer cabinet

Lint should be removed every 2 years, or more often,

depending on dryer usage. Cleaning should be done

by a qualified appliance servicer.

From the Exhaust Vent

Lint should be removed every 2 years, or more often,

depending on dryer usage.

CLEANING THE LiNT SCREEN

Every load cleaning

The lint screen is located in the door opening of the dryer.

The control panel has an indicator light to remind you to

clean the lint screen after each load. A screen blocked

by lint will increase drying time.

To clean:

1. Pull the lint screen straight up. Roll lint off the screen

with your fingers. Do not rinse or wash screen to remove

lint. Wet lint is hard to remove.

2. Push the lint screen firmly back into place.

IMPORTANT:

[] Do not run the dryer with the lint screen loose,

damaged, blocked, or missing. Doing so can cause

overheating and damage to both the dryer and fabrics.

[] If lint falls off the screen into the dryer during removal,

check the exhaust hood and remove the lint. See

"Venting Requirements."

As needed cleaning

Laundry detergent and fabric softener residue can build

up on the lint screen. This buildup can cause longer drying

times for your clothes, or cause the dryer to stop before

your load is completely dry. The screen is probably clogged

if lint falls off while the screen is in the dryer.

Clean the lint screen with a nylon brush every 6 months,

or more frequently, if it becomes clogged due to a residue

buildup.

To wash:

1. Roll lint off the screen with your fingers.

2. Wet both sides of lint screen with hot water.

3. Wet a nylon brush with

hot water and liquid detergent.

Scrub lint screen with the brush

to remove residue buildup.

4. Rinse screen with hot water.

5. Thoroughly dry lint screen with a clean towel.

Reinstall screen in dryer.

NON=USE, STORAGE, AND MOVING CARE

Install and store your dryer where it will not freeze. Because

some water may stay in the hose, freezing can damage

your dryer. If storing or moving your dryer during freezing

weather, winterize it.

Non=Use or Storage Care

Operate your dryer only when you are at home. If you will

be on vacation or not using your dryer for an extended

period of time, you should:

1, Unplug dryer or disconnect power.

2, Clean lint screen. See "Cleaning the Lint Screen."

3, Turn off the water supply to the dryer. This helps to

avoid unintended flooding (due to a water pressure

surge) while you are away.

Moving Care

For power supply cord-connected dryers:

1, Unplug the power supply cord.

2, Gas models only: Close shutoff valve in gas supply line.

3, Gas models only: Disconnect gas supply line pipe and

remove fittings attached to dryer pipe.

4, Gas models only: Cap the open gas supply line.

5, Steam models only: Shut off water faucet.

6, Steam models only: Disconnect the water inlet hose

from faucet, then drain the hose. Transport hose

separately.

7, Make sure leveling legs are secure in dryer base.

8, Use tape to secure dryer door.

F SPECIAL INSTRUCTIONS

FOR STEAM MODELS

Water Inlet Hose

Replace inlet hose and hose screen after 5 years of use

to reduce the risk of hose failure. Periodically inspect and

replace inlet hose if bulges, kinks, cuts, wear, or leaks

are found.

When replacing your inlet hose, record the date

of replacement.

To Winterize the Dryer

1, Unplug dryer or disconnect power.

2, Shut off water faucet.

3, Disconnect water inlet hose from faucet and drain.

To Use the Dryer Again

1, Flush water pipes. Reconnect water inlet hose to faucet.

Turn on water faucet.

2, Plug in dryer or reconnect power as described in the

"installation Instructions".

Electrical Shock Hazard

Disconnect power before servicing,

Replace all parts and panels before operating,

Failure to do so can result in death or electrical shock.

For direct-wired dryers:

1, Disconnect power.

2, Disconnect wiring.

3, Steam models only: Shut off water faucet.

4, Steam models only: Disconnect the water inlet hose from

faucet, then drain the hose. Transport hose separately.

5, Make sure leveling legs are secure in dryer base.

6, Use tape to secure dryer door.

Reinstalling the Dryer

Follow the "installation instructions" to locate, level, and

connect the dryer.

TROUBLESHOOTING

First try the solutions suggested here or visit our website at www.whirlpool.com/product_help -

In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.

If you experience Possible Causes Solution

Dryer will not run

Dryer will not heat

Humming or whining

noise with Steam cycle

selected (on some

models)

Thumping noise

Rattling or vibrating noise

Clicking noise

Clothes are not drying

satisfactorily or drying

times are too long

Door not closed completely.

Start/Pause button not pressed firmly

or held long enough.

Household fuse is blown or circuit

breaker has tripped.

Incorrect power supply.

Wrong type of fuse.

Household fuse is blown or circuit

breaker has tripped.

Incorrect power supply.

Supply line valve not open.

Water inlet valve on dryer is running.

Dryer hasn't been used in a while.

A small object caught between the

edges of dryer drum.

Dryer isn't properly leveled.

Clothing is balled up in dryer.

Gas valve operating.

Lint screen is clogged with lint.

The exhaust vent or outside exhaust

hood is clogged with lint, restricting

air movement.

The exhaust vent is not the correct

length.

The dryer is not level.

The exhaust vent diameter is not the

correct size.

The Air Only temperature setting has

been selected.

The load is too large and heavy to

dry quickly.

Make sure the dryer door is closed completely.

Press and hold the START/PAUSE button 2-5 seconds.

There may be 2 household fuses or circuit breakers for the dryer.

Check that both fuses are intact and tight, or that both circuit

breakers have not tripped. Replace the fuses or reset the circuit

breaker. If the problem continues, call an electrician.

Electric dryers require 240-volt power supply. Check with

a qualified electrician.

Use a time-delay fuse.

The drum may be turning, but you may not have heat. Electric

dryers use 2 household fuses or circuit breakers. Replace the

fuses or reset the circuit breaker. If the problem continues, call

an electrician.

Electric dryers require 240-volt power supply. Check with

a qualified electrician.

For gas dryers, make sure that the valve on the gas supply line

is open.

The water inlet valve on the dryer is used during the Steam function.

If the dryer has just been installed or unused for an extended period,

the valve may be louder and run longer. This is normal.

NOTE: The valve may make this noise even with no water line

connected.

This is normal. The thumping sound should diminish after afew

minutes of use.

Check the front and rear edges of the drum for small objects. Clean

out pockets before laundering.

The dryer may vibrate if not properly installed. See the

installation instructions. All four dryer feet should be in firm

contact with the floor.

When balled up, the load will bounce, causing the dryer to

vibrate. Separate the load items and restart the dryer.

On gas dryers, you may hear the gas valve clicking as it opens

and closes. This is normal.

Clean lint screen before each load.

Run the dryer for 5-10 minutes. Hold your hand under the

outside exhaust hood to check air movement. If you do not

feel air movement, clean exhaust system of lint or replace

exhaust vent with heavy metal or flexible metal vent. See

"installation instructions".

Check that the exhaust vent is not too long or has too many

turns. Long venting will increase drying times. See 'qnstallation

instructions".

Clothes not contacting the moisture sensors during Automatic

cycles. See "Level the Dryer" in the 'qnstallation Instructions".

Use 4" (102 mm) diameter vent material.

Select the right temperature for the types of garments being

dried. See "Cycle Guide".

Separate the load to tumble freely.

TROUBLESHOOTING

First try the solutions suggested here or visit our website at www.whirlpool.com/product_help -

In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.

If you experience

Possible Causes Solution

Clothes are not drying Fabric softener sheets are blocking The air outlet grille is just inside the door, behind the lint

satisfactorily or drying the grille, screen. Check that it is not blocked by afabric softener sheet.

times are too long (cont.) Use only one fabric softener sheet, and use it only once.

The dryer is located in a room with Proper operation of dryer cycles requires temperatures above

temperature below 45°F (7°C). 45°F (7°C).

The dryer is located in a closet. Closet doors must have ventilation openings at the top and

bottom of the door. The front of the dryer requires a minimum of

1" (25 mm) of airspace, and, for most installations, the rear of the

dryer requires 5" (127 mm). See 'qnstallation Instructions".

Cycle time is too short The load may not be contacting the Level the dryer. See "Installation Instructions". All four dryer

sensor strips on Automatic Cycles. feet should be in firm contact with the floor.

Clothes are coming out of the Steam

cycles with damp or wet spots.

The Automatic Cycles are ending

early.

Loose dyes in clothes.

The load was not removed from dryer

at the end of the cycle.

Lint on load Lint screen is clogged with lint.

Stains on load Improper use of fabric softener.

Stains on drum

Loads are wrinkled

The dryer was overloaded.

For steam cycles, the water is not

properly connected with the dryer.

Odors Recent painting, staining, or

varnishing in the area where your

dryer is located.

For Steam Cycles, the water is not

properly connected with the dryer.

Odors are left in garments after

wearing.

Under certain environmental or installation conditions you may

experience underdrying. Select the Quick Refresh cycle. Then

select the appropriate time based on the load to be refreshed.

Change the dryness level setting on Automatic Cycles.

Increasing or decreasing the dryness level will change the

amount of drying time in a cycle. If loads are consistently ending

too early, see also "Changing the Automatic Cycle settings to

increase drying time".

Clean lint screen before each load.

Add dryer fabric softener sheets at the beginning of the cycle.

Fabric softener sheets added to a partially dried load can stain

your garments. Do not use fabric softener sheets with Steam

Cycles.

Drum stains are caused by dyes in clothing (usually blue jeans).

These will not transfer to other clothing.

Select Enhanced Touch Up or Quick Refresh cycles (on some

models) to tumble the load with water and heat. These cycles

are best for smoothing out wrinkles and reducing odors from

loads consisting of wrinkle-free cotton, cotton polyester blends,

common knits, and synthetic garments.

NOTE: Refer to garment care label instructions. Dry clean

only garments are not recommended.

Dry smaller loads that can tumble freely. When using the

Enhanced Touch Up cycle, be sure to select the correct number

of garments to be refreshed. Results may also vary depending

on fabric type. This cycle is best for reducing wrinkles and odors

from loads consisting of wrinkle-free cotton, cotton polyester

blends, common knits, and synthetics.

Make sure water is connected to the dryer. Check that water

inlet hose is connected to both the faucet and dryer's water inlet

valve. Check that the water supply is turned on.

Ventilate the area. When the odors or fumes are gone from the

area, rewash and dry the clothing.

Make sure water is connected to the dryer. Check that water

inlet hose is connected to both the faucet and dryer's water inlet

valve. Check that the water supply is turned on.

To remove odors left in garments after wearing, select Enhanced

Touch Up or Quick Refresh (on some models). These cycles are

best for reducing wrinkles and odors from loads consisting of

wrinkle-free cotton, cotton polyester blends, common knits,

and synthetics.

TROUBLESHOOTING

First try the solutions suggested here or visit our website at www.whirlpool.com/product_help -

In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.

If you experience

Load too hot

Possible Causes

Load removed before cool down

portion of cycle complete.

Using Timed Dry Cycle with a high

temperature setting.

The drying cycle has been interrupted

by a power failure.

There may be a problem with your

home power supply keeping the

dryer's heater from turning on.

"PF" (power failure)

"L2" Diagnostic Code

(low or no line voltage

condition)

Solution

Allow the dryer to complete the cool down portion of the cycle

before removing the load.

Select an Automatic cycle with a lower heat setting to avoid

overdrying the load.

Press START/PAUSE twice to resume the cycle, or press

POWER to select a new cycle.

The dryer will continue to run when this diagnostic code

is present. Press any key to clear the code from the display

and return to the estimated time remaining.

Try the following:

Check to see if a household fuse has blown or circuit

breaker has tripped. Electric dryers use two household fuses

or breakers. Replace the fuse or reset the circuit breaker.

Confirm the power cord is properly installed. Refer to

"Installation Instructions" for details.

Select a Timed Dry heated cycle, and restart the dryer.

If the message persists, consult a qualified electrician.

"F# E#" (F1 El, F3 El, The dryer is in need of service. If a code beginning with an "F" appears in the display.

etc.) variable service Alternating between F# and E#, the dryer control has

codes, detected a problem that requires service. Call for service.

WHIRLPOOL CORPORATION LAUNDRY WARRANTY

LiMiTED WARRANTY

For one year from the date of purchase, when this major appliance is installed, operated, and maintained according to instructions

attached to or furnished with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter "Whirlpool") will pay for Factory

Specified Replacement Parts and repair labor to correct defects in materials or workmanship that existed when this major appliance

was purchased.

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.

Service must be provided by a Whirlpool designated service company. This limited warranty is valid only in the United States or

Canada and applies only when the major appliance is used in the country in which it was purchased. This limited warranty is effective

from the date of original consumer purchase. Proof of original purchase date is required to obtain service under this limited warranty.

ITEMS EXCLUDED FROM WARRANTY

This limited warranty does not cover:

1. Replacement parts or repair labor if this major appliance is used for other than normal, single-family household use or when it is

used in a manner that is inconsistent to published user or operator instructions and/or installation instructions.

2. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or

repair house fuses, or to correct house wiring or plumbing.

3. Service calls to repair or replace appliance light bulbs, air filters, or water filters. Consumable parts are excluded from warranty

coverage.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in

accordance with electrical or plumbing codes, or use of products not approved by Whirlpool.

5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage

results from defects in materials or workmanship and is reported to Whirlpool within 30 days from the date of purchase.

6. Pick up and delivery. This major appliance is intended to be repaired in your home.

7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

8. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an

authorized Whirlpool servicer is not available.

9. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance

with Whirlpool published installation instructions.

10. Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered, or

cannot be easily determined.

The cost of repair or replacement under these excluded circumstances shall be borne by the customer.

DISCLAIMER OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABiLiTY OR iMPLiED WARRANTY OF FITNESS

FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and

provinces do not allow limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply

to you. This warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to

province.

DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY

Whirlpool makes no representations about the quality, durability, or need for service or repair of this major appliance other than the

representations contained in this Warranty. if you want a longer or more comprehensive warranty than the limited warranty that comes

with this major appliance, you should ask Whirlpool or your retailer about buying an extended warranty.

LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.

WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow

the exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This

warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.

Ifoutside the 50 United States and Canada, contact your authorized Whirlpool dealer to determine if another warranty applies.

Ifyou think you need repair service, first see the "Troubleshooting" section of the Use & Care Guide. If you are unable to resolve

the problem after checking "Troubleshooting," additional help can be found by checking the "Assistance or Service" section or by

calling Whirlpool. In the U.S.A., call 1-800-253-1301. In Canada, call 1-800-807-6777. 10/11

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation

date for in-warranty service.

Write down the following information about your major appliance

to better help you obtain assistance or service if you ever need

it. You will need to know your complete model number and serial

number. You can find this information on the model and serial

number label located on the product.

Dealer name

Address

Phone number

Model number

Serial number

Purchase date

S] CURIT] DE LA S] CHEUSE

Votre s_curit_ et celle des autres est tr_s importante.

Nous donnons de nombreux messages de securit6 importants dans ce manuel et sur votre appareil m6nager. Assurez-vous de

toujours lire tousles messages de s_curit6 et de vous y conformer.

Voici le symbole d'alerte de s_curit&

Ce symbole d'alerte de s_curit6 vous signale les dangers potentiels de d_c_s et de blessures graves &vous

et & d'autres.

Tousles messages de s6curit_ suivront le symbole d'alerte de s6curit_ et le mot "DANGER" ou

"AVERTISSEMENT". Ces mots signifient :

Risque possible de d_c_s ou de blessure grave si vous ne

suivez pas imm_diatement les instructions.

Risque possible de d_c_s ou de blessure grave si vous

ne suivez pas les instructions.

Tous les messages de s_curit6 vous diront quel est le danger potentiel et vous disent comment r6duire le risque de blessure et

ce qui peut se produire en cas de non-respect des instructions.

- "Risque d'incendie"

L'installation de la s_cheuse h linge doit 6tre effectu_e par un installateur qualifi_.

Installer la s_cheuse conforrn_rnent aux instructions du fabricant et aux codes Iocaux.

Ne pas installer de s_cheuse _ linge avec des rnat_riaux d'_vacuation en plastique

souple ou un conduit rn_tallique souple (de type papier d'aluminium). Si un conduit

rn_tallique souple est installS, celui-ci dolt _tre d'un type sp_cifique identifi_ par le

fabricant de i'appareil et convenir _ une utilisation avec les s_cheuses _ linge. Les

rnat_riaux d'_vacuation souples sont connus pour s'affaisser, 6tre facilement _cras_s

et bloquer la charpie. Ces situations obstrueront le d_bit d'air de la s_cheuse _ linge et

augmenteront le risque d'incendie.

Pour r6duire ie risque de blessure grave ou de d_c_s, suivre routes

les instructions d'installation.

Conserver ces instructions.

Dans I'l'Etatdu Massachusetts, les instructions d'installation suivantes sont applicables :

[] Les travaux d'installation et r6paration doivent 6tre execut6s par un plombier ou tuyauteur qualifie ou licencie, ou par le

personnel qualifie d'une entreprise licenciee par I'€:tat du Massachusetts.

[] Si une vanne h boisseau sph@ique est utilisee, elle doit comporter une manette "T".

[] Si un conduit de raccordement flexible est utilis6, sa Iongueur ne doit pas d6passer 3 pi.

Avertissements de la proposition 65 de I'Etat de Californie '

AVERTISSEMENT " Ce produit contient au moins un produit chimique connu par I'#tat de Californie pour 6tre & I'origine de

cancers.

AVERTISSEMENT : Ce produit contient au moins un produit chimique connu par I'Etat de Californie pour 6tre h I'origine de

malformations et autres d_ficiences de naissance.

AVERTISSEMENT : Pour votre s_curit_, les renseignements darts ce manuel doivent

_tre observes pour r_duire au minimum les risques d'incendie ou d'explosion ou pour

_viter des dommages au produit, des blessures ou un d_c_s.

- Ne pas entreposer ou utiliser de I'essence ou d'autres vapeurs ou liquides

inflammables _ proximit_ de cet appareil ou de tout autre appareil _iectrom_nager.

- QUE FAIRE DANS LE CAS D'UNE ODEUR DE GAZ :

®hie pas tenter d'allumer un appareil.

= Ne pas toucher a un commutateur electrique; ne pas utiliser le t61_phone se trouvant

sur les lieux.

®Evacuer tousles gens de la piece, de I'_difice ou du quartier.

®Appeler imm6diatement le fournisseur de gaz d'un t616phone voisin. Suivre ses

instructions.

= A defaut de joindre votre fournisseur de gaz, appeler les pompiers.

- L'installation et I'entretien doivent _tre effectues par un installateur qualifie, une

agence de service ou le fournisseur de gaz.

AVERTISSEMENT : L'odorat ne permet pas toujours la d_tection d'une fuite de gaz.

Les distributeurs de gaz recommandent I'emploi d'un detecteur de gaz (homologation UL ou CSA).

Pour d'autre information, contacter le fournisseur de gaz local.

En cas de detection d'une fuite de gaz, executer les instructions "Que faire dans le cas d'une odeur de gaz".

iMPORTANT : L'installation du gaz dolt se conformer aux codes Iocaux, ou en I'absence de codes Iocaux, au code canadien

d'installation B149.1 du gaz naturel ou du propane.

La s6cheuse doit _tre electriquement reli6e &la terre conform6ment aux codes Iocaux, ou en I'absence de codes Iocaux, au Code

canadien de 1'61ectricite, CSA C22.1.

IMPORTANTES INSTRUCTIONS DE S(=CURIT¢:

AVERT_SSEMENT : Pour r6duire le risque d'incendie, de choc 61ectrique ou de blessure Iors de I'utilisation de

la secheuse, il convient d'observer certaines precautions el6mentaires dont les suivantes :

[] Life toutes les instructions avant d'utiliser la s6cheuse.

[] Ne pas placer des articles expos6s aux huiles de cuisson

dans votre secheuse. Les articles contamin6s par des

huiles de cuisson peuvent contribuer & une r6action

chimique qui pourrait causer a la charge de s'enflammer.

[] Ne pas faire s6cher dans la machine des articles qui ont

deja et6 nettoyes, laves, imbibes, ou taches d'essence,

de solvants pour nettoyage a sec, d'autres substances

inflammables, ou de substances explosives puisqu'elles

degagent des vapeurs qui peuvent provoquer un

incendie ou une explosion.

[] Ne pas permettre a des enfants de jouer sur ou

I'int@ieur de la secheuse. Une surveillance etroite est

n6cessaire Iorsque la s6cheuse est utilis6e pros d'eux.

[] Avant d'enlever la s6cheuse du service ou lajeter, enlever

la porte du compartiment de s6chage.

[] Ne pas mettre la main dans la s6cheuse si le tambour est

en mouvement.

[] Ne pas installer ni entreposer la secheuse oQ elle sera

expos6e aux intemp@ies.

[] Ne pas jouer avec les commandes.

[] Ne pas r6parer ni remplacer une piece de la s6cheuse ou

essayer d'en faire I'entretien & moins d'une recommandation

sp6cifique dans le guide d'utilisation et d'entretien, ou

publiee dans les instructions de reparation par I'utilisateur

que vous comprenez et pouvez ex6cuter avec comp6tence.

[] Ne pas utiliser un produit assouplissant de tissu ou des

produits pour 61imJner la statique &moins qu'ils ne soJent

recommand6s par le fabricant du produit assouplissant de

tissu ou du produit.

[] Ne pas utiliser la chaleur pour faire s6cher des articles

fabriqu6s avec du caoutchouc mousse ou des mat6riaux

semblables.

[] Nettoyer le filtre & charpie avant et apres chaque charge.

[] Ne pas laisser la charpie, la poussiere, ou la salete

s'accumuler autour du syst_me d'6vacuation ou autour de

I'appareil.

[] Un nettoyage periodique de I'interieur de la secheuse et du

conduit d'6vacuation doit _tre effectue par une personne

qualifi6e.

[] Pour les instructions de liaison & la terre, voir "Sp6cifications

electriques" dans les instructions d'installation.

CONSERVEZ CES INSTRUCTIONS

VITRIFICATION D'UNE CIRCULATION flAIR ADI QUATE

POUR LE SYSTI ME D'EVACUATION

Risque d'incendie

Utiliser un conduit d'_vacuation en m_tal Iourd.

Ne pas utiliser un conduit d'_vacuation en plastique.

Ne pas utiliser un conduit d'_vacuation en feuille

de rn_tal.

Le non-respect de ces instructions peut causer

un d_c_s ou un incendie.

fCirculation d'air adequate

Une s6cheuse a besoin de chaleur et d'une circulation d'air

ad@uate pour s@her efficacement le linge. Une ventilation

ad@uate r6duit les dur@s de s6chage et accroTt les

6conomies d'@ergie. Voir les Instructions d'installation.

Le systeme d'@acuation fix6 h la s6cheuse joue un r61e

important dans la circulation de I'air.

Les interventions de d@annage caus@s par

une ventilation incorrecte ne sont pas couvertes par

la garantie et seront a la charge du client, quel que

soit I'installateur de la s6cheuse.

Maintenir une bonne circulation d'air

en effectuant les operations suivantes :

[]

Nettoyer le filtre a charpie avant chaque

charge.

Remplacer le mat6riau de conduits

d'@acuation en plastique ou en aluminium

par des conduits d'@acuation Iourds et

rigides de 4" (102 mm) de diametre.

[]

r6duit le flux d'air.

Bonne

Toujours employer les conduits d'@acuation les plus

courts possible.

Ne pas utiliser plus de quatre coudes h 90 °dans

un circuit d'@acuation car chaque inclinaison et courbe

I M

[] Retirer la charpie et les r6sidus du clapet d'@acuation.

[] Retirer la charpie sur toute la Iongueur du circuit

d'@acuation au moins tousles 2 ans. Apr_s le

nettoyage, veuillez suivre les instructions d'installation

fournies avec la s6cheuse pour une v6rification finale de

I'appareil.

[] D6gager tout article qui se trouverait devant la s6cheuse.

Utiliser les programrnes de d_tection pour un meiileur soin du tissu

et davantage d'_conomies d'_nergie

Utiliser les programmes de d6tection pour que la s6cheuse permette de r@liser davantage d'6conomies d'@ergie et d'apporter

un soin sup6rieur aux tissus. Durant les programmes automatiques, la temp6rature de s6chage de Fair et le niveau d'humidit6

sont d6tect6s dans la charge. Cette d6tection se pro@it tout au long du programme de s6chage et la s6cheuse s'6teint Iorsque

la charge atteint le degr6 de s6chage s61ectionn6. Utiliser le niveau de s6chage NORMAL pour pouvoir r@liser un maximum

d'6conomies d'@ergie.

Avec les programmes minut6s, la s6cheuse fonctionne pendant la dur@ r6gl@, ce qui peut parfois entrafner le r6tr@issement

ou le froissement du linge, et I'accumulation d'61ectricit6 statique due au s6chage excessif. Utiliser les programmes minut6s

pour une charge encore humide n6cessitant un peu de temps suppl6mentaire ou Iorsqu'on utilise la grille de s6chage.

Oonseils pour obtenir la meilleure performance de votre s_cheuse avec vapeur

[] Les r_sultats peuvent varlet selon le tissu. II est possible [] Le programme Enhanced Touch Up (Retouche am_lior@)

que les v_tements 100 % coton avec fini infroissable est id@l pour d_sodoriser et la r_duction des pits I_gers

donnent de meilleurs r_sultats que les autres. II est dans des charges de v_tements secs petites a moyennes.

possible que les articles 100 % coton n@essitent un Pour le programme Enhanced Touch Up (Retouche

rafra?chissement suppl_mentaire apr_s le programme am_lior@), la dur@ est s_lectionnable par increments

vapeur de cinq minutes, selon le volume de la charge.

[] Uemploi d'une feuille d'assouplissant de tissu n'est pas [] Le programme Quick Refresh (Refra_chissement rapide)

recommand_ avec les programmes a vapeur. Ceci pourrait (sur certains mo@les) est id@l pour aider _.d_froisser

causer des t_.ches temporaires sur les v_tements et d_sodoriser les v_tements secs, y compris une charge

de linge qui a _t_ laiss_e dans la s_cheuse. Pour le

[] L'utilisation de programmes a vapeur n'est pas

recommand@ pour des articles amidonn_s. Laver programme, Quick Refresh (Refra?chJssement rapide) la

les articles amJdonn_s ou neufs avant d'utiliser dur@ de s_chage est automatiquement ajust_e a mesure

un programme avec vapeur, que la charge est d_tect@. La dur_e de fonctionnement

d'un programme ne peut pas _tre ajust@ manuellement.

La page charge ...

Whirlpool YWED8500BC0 Le manuel du propriétaire

Marque: Whirlpool

Modèle: YWED8500BC0

Catégorie: Sèche-linge électriques

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Whirlpool YWED8500BC0 Owner's manual

Whirlpool YWED8500BC0 Le manuel du propriétaire

Whirlpool YWED8500BC0 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents