FlinQ FQC8208 Manuel utilisateur

Marque: FlinQ

Modèle: FQC8208

Taper: Manuel utilisateur

01 04 0502 03 06 07 08

FLINQ LED FLOORLAMP XYRO

FQC8208

V1 USER MANUAL

Thanks for purchasing this FlinQ product!

To ensure continuous operation and accuracy, please read these operating instructions carefully before use and save this manual for future use. To skip certain

procedures may result in incorrect reading and use. We hope that you will enjoy using your new product!

If by any chance the item is damaged, defective or broken, you are covered with warranty! Please do not hesitate to contact us for any questions, concerns or

suggestions at the email address as mentioned in this manual. We deserve the right to make technical and design modiﬁcations in the course of continuous

product development. Read and follow the instructions contained in this manual carefully. Keep these instructions at a safe place for future reference.

REMOTE CONTROL:

Buttons: 10x

Button function: ON/OFF, SYMPHONY START/PAUSE, SPEED +/-, BRIGHTNESS +/-, LIGHT SWITCH, SYMPHONIC MODE +/-, RING COLOR

Remote control type: RF433 radio frequency remote control

Remote control distance: up to 30 meters (open area)

Remote control power supply: 3x AAA batteries

Control quantity: One remote control can control multiple lights (only for the single colors) or 1 light selectable for your choice

This product is a lifestyle product.

Read and follow the instructions contained in this manual carefully. Keep these instructions at a safe place for future reference.

The operating life of the product will be less if the ambient temperature is higher than 45°C or lower than -10°C.

Product general description and contents:

1. Lamp pole

2. Lamp foot base

3. Adapter + connection cable (2.5m) with USB plug

4. RF Remote control

5. Installation bolt + tool and user manual

Safety Information:

Please read this manual thoroughly before using the product! Keep it in hand for future reference. Warnings alert the user to potential serious outcomes, such as

injury or adverse events to the user. Cautions alert the user to exercise care necessary for the safe and eﬀective use of the product. Notes contain important

information that may be overlooked or missed.

This product can be used indoors (see below for more info).

This appliance may be used by children aged 6 and over, and by persons with reduced physical, sensory or mental capacities or a lack of suﬀicient experience

and/or knowledge, provided they are supervised or have been trained in the safe use of the appliance and understand the potential dangers.

Cleaning and maintenance must not be carried out by children without supervision. Children must not be allowed to play with the appliance.

Keep the packaging material away from children. There is a risk of suﬀocation!

Do not allow unsupervised children to clean or maintain this device.

• WARNING! Do not leave packaging material lying around carelessly. This may become dangerous playing material for children. Risk of suﬀocation!

• DANGER due to swallowing small parts. Keep these away from children. Risk of suﬀocation!

SPECIFICATIONS:

Input voltage: AC 100-240V / 50-60Hz

Rated output/input voltage lamp: DC 5V- 3A (3400mA) max with 2.5MT cable

Rated power: 18W

Energy label: A

Control method: RF433 soft touch wireless remote control with color,

speed and dimming function and much more

Appearance color: full dark black

Product height size: 145cm * 240mm*240mm base foot

Light color: RGB Symphony colors + Cool White + Warm White chosen at any way possible

Display index: CRI>80

Number of lamp LED beads: 225pcs

Product color temperature: warm white (2700-3200K) / white (6000-6500K) / RGB Symphony Colors

Lumen: 1650 for Warm White and 1800 for White/Cool White

LED life: 25000 hours max.

Working temperature: 0 ~ + 45

IP Grade: IP20 (indoor use only)

Shell material: PE White + metal iron spray paint

Net weight: 2.78Kg

Lighting Symphony colors mode +/- : +/- 238 lighting eﬀects

MAIN USE CAUTIONS BEFORE INSTALLATION:

NOTE:

• Choose a stable, solid and supportive surface and make sure the lamp is set correctly.

• Make sure the cables cannot cause a trip hazard.

• Make sure there is enough ventilation around the device and so not cover it at all times.

• This lamp is intended for inside use and the main power adapter and remote control is not waterproof! Keep away from water and only use indoors.

WARNING: Keep the external adapter out of reach of children.

Never charge this product in moisture conditions or in the rain. Only charge it indoors, in a dry place.

• This is not a TOY, keep away from small children below 12 years.

• Do not open or disassemble the lamp or adapter yourself, this will void the warranty at all times.

•Do not disassemble, repair or modify the product by yourself as this may result into an electric shock.

•Do not look directly into the lamp beads as it could hurt your eyes.

•The led source is not replaceable.

•If the cable or adapter is damaged or broken please contact your seller for correct replacement by the manufacturer only.

• Do not stand, sit on, jump or throw with the lamp at all times.

•Do not throw this product in the air as it may cause damage by falling.

• Only use the lamp for its intended designed use as a light.

• Take good care of the product and clean it regularly.

• Never touch the plug contacts with sharp or metal objects.

• Use only the original power supply and original accessories.

• Do not use the device outdoors.

• Protect the device from special liquids and vapors.

NOTE:

• Please note that the power port of the device should not be inﬁltrated by water. Otherwise, it will cause a product failure.

• Do not charge or store the product in a place below 0 or above 40 , otherwise the product performance will be reduced.

• It is a normal phenomenon that temperature of the adapter rises during use.

INSTALLATION OF LAMP FOOT BASE WITH LAMP POLE:

OPERATION AND REMOTE CONTROL USE:

NOTE:

Do not connect the power cable nor adapter to the power mains outlet yet!

Please check if the lamp set is complete according the package contents as described.

1. Place the lamp pole carefully on a table that is protected by a soft cloth or towel etc.

2. Take the lamp pole bottom screw side in one hand and bolt it with your other hand on the lamp foot base hole with the supplied tool and bolt. Fix it ﬁrmly but

slow, carefully.

3. Insert the USB connector cable end included into the approved adapter power connection to connect and insert it to the mains power outlet. The power

adapter input is AC100-240V 50/60Hz with output from DC 5V-3A (3400mA) max. Keep in mind this adapter is NOT waterproof and needs to be used only

INDOORS.

First install 3x AAA (LR03) 1,5V batteries (not included, optional). To open the battery cover at the back side use a small coin to twist and open it at

the side of the remote back cover (see picture).

Clean the battery contact and remote contacts before installing the batteries. Install the three batteries 1 by 1 and make sure to use the correct polarity + and –

inside the remote control housing. Put the battery cover back into its place and make sure that all sides are correctly “clicked” and pushed inside the housing of

the remote top housing.

The remote can be used for the change of colors, to dim the light, to speed up or down, start/pause function controls and more. The remote control is not

waterproof! The maximum control distance is <30 meters without obstacles and in open space.

NOTE: Remove the batteries from the product if it will not be used for a long time (1 month or longer) or when the remote control is not

working anymore (replace when needed).

BUTTON USE EXPLANATIONS:

1: ON/OFF >>> Put the lamp ON or OFF

2: START/PAUSE >>> In the symphonic mode you can press to start and pause the lights way at any moment. Press the color ring ﬁrst and then press start again,

the light will now go into automatic play mode from ﬁrst setting.

3: COLOR RING >>> Short press or slide the color ring with your ﬁnger to select the desired color. When in normal white mode ( 1 color static) you can adjust the

color temperature with this ring.

4: SPEED + / COLOR TEMPERATURE + >>> When in symphonic mode or color mode you can increase the speed of the light. In white mode you can adjust the

color temperature upwards.

5: SPEED - / COLOR TEMPERATURE - >>> When in symphonic mode or Color mode you can decrease the speed of the light. In white mode you can adjust the

color temperature downwards.

6: LIGHT SWITCH >>> White mode colors only or switch back to Color/Symphonic mode.

7: BRIGHTNESS - >>> The brightness can be decreased on both Color/Symphonic mode.

8: BRIGHTNESS + >>> The brightness can be increased on both Color/Symphonic mode.

9: SYMPHONIC MODE - >>> Several moving and special mode’s/colors etc can be selected downwards.

10: SYMPHONIC MODE + >>> Several moving and special mode’s/colors etc can be selected upwards.

USE ONE REMOTE ON MORE LAMPS AT THE SAME TIME:

One remote can be used on one lamp or with more lamps at the same time. You can “pair” the remote and the ﬂoorlamp within a range of <5 meters of the lamp.

To pair and use the remote with only 1 lamp in one room/space, please:

1. Make sure the lamp is ON.

2. Long press the LIGHT SWITCH button for 5-6 seconds, the light will ﬂash quickly 5x to conﬁrm that is paired for 1 remote control now.

To pair and use the remote with more than 1 lamp in the same/more rooms/spaces (optional to buy more lamp sets separately at www.ﬂinqproducts.nl ) please:

1. Make sure the lamp is ON.

2. Long press the LIGHT SWITCH button for 5-6 seconds, the light will ﬂash slowly 5x to conﬁrm that the lamp is paired for the use with more than 1 remote

control.

Note: Make sure when you to this process that other optional bought lamps are switched OFF before pairing.

SECURITY AND IMPORTANT SAFETY INSTRUCTIONS:

When using electrical products, certain precautions must be followed, including the following:

READ AND FOLLOW ALL SAFETY INSTRUCTIONS.

This IP20 product is suitable for indoor use.

Please use the rated input voltage power supply of the product as mentioned on the back label.

Do not install near a gas device or other sources with a similar heating process.

Do not use the product outside its intended use.

Read and follow all instructions that are indicated on the product or supplied with it.

Keep this manual for future reference.

CAUTION:

• NON-Replaceable LED lights!

1 2

1: ON/OFF

2: START/PAUSE

3: COLOR RING

4: SPEED + / COLOR TEMPERATURE +

5: SPEED - / COLOR TEMPERATURE -

6: LIGHT SWITCH

7: BRIGHTNESS -

8: BRIGHTNESS +

9: SYMPHONIC MODE -

10: SYMPHONIC MODE +

INSTRUCTIONS FOR USE AND MAINTENANCE:

In case of non-use, store the product in a cool and dry place away from direct sunlight.

TROUBLESHOOTING TIPS IF THE LIGHT DOES NOT WORK:

Light does not turn on?

• Button use >>> Try to power on/oﬀ by the button remote or re-connect the USB cable connection or adapter from the main power outlet.

• Remote control not working >>> The RF signal maybe weak when there is a strong visible light or barrier. Normal range should be eﬀective within 30 meters.

Or remove the old batteries by opening the battery cover and remove of the cover from the remote control. Take notice of the positive (+) and negative (-) side of

the batteries, make sure that the new batteries (AAA 1,5V) is inserted the right way. Click the cover back on and dispose of the old battery responsibly.

• Not working >>> Is the battery full from the remote? Please replace and make sure the adapter is connected to the mains power and retry.

• Poor distance >>> Use it inside a range of max. 30 meters without any obstacles.

The battery runs out too quick?

• Weak battery: We suggest only to use dry alkaline batteries from A-brands.

NOTE:

If the lamp does not work or respond at any possible way by the remote please disconnect the power adapter from the mains power outlet and wait

for at least 15min and then re-connect it again.

CLEANING THE DEVICE ITSSELF:

Make sure the lamp is kept dust free and clean. Clean it regularly with a dry anti-static cloth and with warm, soapy water but make sure that no water liquid

can enter the lamp luminaire. Dry the lamp before turning it ON again.Please do not immerse the main unit in water, it is not waterproof!

Wipe gently with a clean soft cloth (microﬁber) dampened with water or a mild detergent.

Do not use a strong irritant lotion such as gasoline, alcohol or rubber water.

This product is designed, produced and tested in accordance with the strictest European safety directive’s and test standards.

WASTE ELETRICAL & ELECTRONIC EQUIPMENT

Disposal Information

Separate collection.

This symbol means the product must not be discarded with the general household waste. There is a separate collection system for these products.

DISCLAIMER

Information in this document is subject to change without notice. The manufacturer does not make any representations or warranties (implied or otherwise)

regarding the accuracy and completeness of this document and shall in no event be liable for any loss of proﬁt or any commercial damage, including but not

limited to special, incidental, consequential or other damage. No part of this document may be reproduced or transmitted in any form by any means, electronic

or mechanical, including photocopying, recording or information recording and retrieval systems without the expressed written permission of the manufacturer.

Our company owns all right to this unpublished work and intends to maintain this work as conﬁdential. Our company may also seek to maintain this work as an

unpublished copyright. This publication is to be used solely for the purpose of reference, operation, maintenance or repair of our equipment. No part of this can

be disseminated for other purposes. In the event of inadvertent or deliberate publication, our company intends to enforce its right to this work under copyright

laws as a published work. Those having access to this manual may not copy, disseminate or disclose the information in this work unless expressly authorized by

our company. All information contained in this manual is believed to be correct. Our company shall not be liable for errors contained herein nor for incidental or

consequential damages in connection with the furnishing, performance, or use of this material. This publication may refer to information and protected by

copyrights or patents and does not convey any license under the patent rights of our company, nor the rights of others. Our company does not assume any

liability arising out of any infringements of patents or other rights of third parties described at any time without notice or obligation. Also, content of the manual

is subject to change without prior notice.

Warranty

The warranty begins on the date of purchase and expires after 24 months. The warranty period is considered to have started three months after the date of

manufacturing indicated on the product or as derived from the serial number of the product. If any defect due to faulty materials and/or workmanship occurs

within the warranty period, we will make arrangements for service. Where a repair is not possible or is deemed uneconomical we may agree to replace the

product. Replacement will be oﬀered at our discretion and the warranty will continue from the date of original purchase. The warranty applies provided the

product has been handled properly for its intended use and in accordance with the operating instructions.

Support, warranty and questions information: info@ﬂinqproducts.nl

This product is designed, produced and tested in accordance with the strictest European safety directive’s and test standards.

WEEE, the waste electrical and electronic equipment directive This marking shown on the product or its literature, indicates that it should not be disposed

with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal,

please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household user should contact

either the retailer where they purchased this product or their local government oﬀice for details of where and how they can take this item for environmentally

safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with

other commercial wastes for disposal. Do not dispose of batteries in your household waste. Dispose of batteries by taking them to your local recycling store or

station, contact your local government oﬀice for more details.

EU DECLARATION OF CONFORMITY

DÉCLARATION DE CONFORMITÉ DE L'UE

Hereby we,

Par la présente, nous,

Company:

Entreprise:

FlinQ Commerce

Address/Adresse:

Eemweg 74,

3755 LD Eemnes,

The Netherlands

Declare under the sole

responsibility that the

following equipment:

Déclare sous sa seule

responsabilité que le

matériel suivant:

Product brand:

FlinQ Commerce

Marque du produit :

FlinQ Commerce

Product name:

Design Floorlamp Xyro

Nom du produit:

Lampadaire Design Xyro

Product Number:FQC8208

Numéro de produit:FQC8208

Product Rating:

DC 5V 3000mA = 3A max

Classement des produits:

DC 5V 3000mA = 3A max

Product type:

Floorlamp

Type de produit:

Lampadaire

Authorized signature:

Signature autorisée :

Name/Nom:

Erwin honing

Title/Titre:

CEO FlinQ commerce

Place/Lieu:

EEMNES

Date/Date:

31-03-2021

Conform that the products mentioned are with the following safety and hazardous

substances restrictions in electrical and electronic equipment requirements of the

relevant European Union harmonization directives 2014/53/EU, 2014/30/EU,

(EC)2019/1021, (EC)NO 850/2004, (EC)NO 1907/2006, (EU)2015/863, (EU)2017/2102,

2011/65/EU, 2012/19/EU and all amendments. Conformity Is guaranteed by the CE

symbol. This product has been tested following harmonized standards and EU

community legislation specifications, applying versions will be valid in March 2021. The

full text of the EU declaration of conformity is available at the following internet address:

www.flinqproducts.nl

TECHNICAL CHANGES SUBJECT TO FURTHER

DEVELOPMENTS

Conforme que les produits mentionnés sont avec les restrictions de sécurité et de

substances dangereuses suivantes dans les exigences des équipements électriques et

électroniques des directives d'harmonisation de l'Union européenne 2014/53/EU,

2014/30/EU, (EC)2019/1021, (EC)NO 850/2004, (EC)NO 1907/2006, (EU)2015/863,

(EU)2017/2102, 2011/65/EU, 2012/19/EU, et tous les amendements. La conformité est

garantie par le symbole CE. Ce produit a été testé conformément aux normes

harmonisées et aux spécifications de la législation communautaire de l'UE, les versions

applicables seront valables en Mars 2021. Le texte complet de la déclaration de

conformité de l'UE est disponible à l'adresse internet suivante : www.flinqproducts.nl

MODIFICATIONS TECHNIQUES RESERVEES AVEC DES DEVELOPPE-

MENTS ULTERIEURS

HARMONISED STANDARDS/ NORMES HARMONISÉES:

EN 55015:2019

EN 61547: 2009

EN 61000-3-2: 2019

EN 61000-3-3: 2013+A1:2019

EN 301 489-1 V2.2.3(2019-11)

EN 301489-3 V2.1.1(2019-03)

EN 300220-1 V3.1.1(2017-02)

EN 300220-2 V3.2.1(2018-06)

EN 62479：2010

EN 60598-1:2015+A1:2018

EN 60598-2-4:2018，

EN 62031:2008+A1:2013+A2:2015

EN 62493:2015

IEC 62321-5:2013

IEC 62321-4:2013+AMD1:2017

IEC 62321-7-1:2015

IEC 62321-7-2:2015

IEC 62321-6:2015

IEC 62321-8:2017

AfPS GS 2019:01 PAK

EU COMMUNITY LEGISLATION/ LÉGISLATION COMMUNAUTAIRE DE L'UE:

Electromagnetic Compatibility Directive (EMC) 2014/30/EU

Radio Equipment Directive (RED) 2014/53/EU

Reduction of Hazardous Substances (ROHS) Directive 2011/65/EU + 2015/863/EU

and (EU)2017/2102

REACH Regulation 1907/2006

Waste Electrical and Electronic Equipment (WEEE) Directive 2012/19/EU

Regulation on Persistent Organic Pollutants (POP) 2019/1021

Product Safety Act PAH AfPS GS 2019:01 PAK

EU-CONFORMITEITSVERKLARING

EU-KONFORMITÄTSERKLÄRUNG

Hierbij,

Hiermit,

Bedrijf:

Unternehmen:

FlinQ Commerce

Adres/Adresse:

Eemweg 74,

3755 LD Eemnes,

The Netherlands

verklaart onder de

exclusieve

verantwoordelijkheid

dat het volgende product:

erklärt, unter alleiniger

Verantwortung dass die

folgende Ausrustung:

Merknaam :

FlinQ Commerce

Produktmarke :

FlinQ Commerce

Product naam:

Design vloerlamp Xyro

Produktname:

Design Stehleuchte Xyro

Product nummer:FQC8208

Produkt-Nummer:FQC8208

Product waardering:

DC 5V 3000mA = 3A max

Produktbewertung :

DC 5V 3000mA = 3A max

Product type:

Vloerlamp

Produkttyp:

Stehlampe

Bevoegde handtekening:

Autorisierte Unterschrift:

Naam/Name:

Erwin honing

Titel/Titel:

CEO FlinQ commerce

Plaats/Ort:

EEMNES

Datum/Datum:

31-03-2021

Conformeert dat de genoemde producten zijn met de volgende veiligheid en gevaarlijke

stoffen beperkingen in elektrische en elektronische apparatuur eisen van de relevante

Europese Unie harmonisatie richtlijnen 2014/53/EU, 2014/30/EU, (EC)2019/1021, (EC)NO

850/2004, (EC)NO 1907/2006, (EU)2015/863, (EU)2017/2102, 2011/65/EU, 2012/19/EU en alle

amendementen. De conformiteit wordt gegarandeerd door het CE-symbool. Dit product is

getest volgens geharmoniseerde normen en specificaties van de EU-communautaire

wetgeving, geldende versies zullen geldig zijn in Maart 2021. De volledige tekst van de

EU-conformiteitsverklaring is beschikbaar op het volgende internetadres:

www.flinqproducts.nl

TECHNISCHE WIJZIGINGEN ONDER VOORBEHOUD VAN VERDERE

ONTWIKKELINGEN

Die Konformität der genannten Produkte mit den folgenden Sicherheits- und Gefahrstoff-

beschränkungen in Elektro- und Elektronikgeräten entspricht den Anforderungen der

relevanten Harmonisierungsrichtlinien der Europäischen Union 2014/53/EU, 2014/30/EU,

(EC)2019/1021, (EC)NO 850/2004, (EC)NO 1907/2006, (EU)2015/863, (EU)2017/2102,

2011/65/EU, 2012/19/EU und allen Änderungen. Die Konformität wird durch das

CE-Zeichen garantiert. Dieses Produkt wurde nach harmonisierten Normen und den

Vorgaben der EU-Gemeinschaftsgesetzgebung in der im März 2021 gültigen Fassung

geprüft. Den vollständigen Text der EU-Konformitätserklärung finden Sie unter folgender

Internetadresse: www.flinqproducts.nl

TECHNISCHE ÄNDERUNGEN UND WEITERENTWICKLUNGEN

VORBEHALTEN

GEHARMONISEERDE NORMEN/ HARMONISIERTE NORMEN:

EN 55015:2019

EN 61547: 2009

EN 61000-3-2: 2019

EN 61000-3-3: 2013+A1:2019

EN 301 489-1 V2.2.3(2019-11)

EN 301489-3 V2.1.1(2019-03)

EN 300220-1 V3.1.1(2017-02)

EN 300220-2 V3.2.1(2018-06)

EN 62479：2010

EN 60598-1:2015+A1:2018

EN 60598-2-4:2018，

EN 62031:2008+A1:2013+A2:2015

EN 62493:2015

IEC 62321-5:2013

IEC 62321-4:2013+AMD1:2017

IEC 62321-7-1:2015

IEC 62321-7-2:2015

IEC 62321-6:2015

IEC 62321-8:2017

AfPS GS 2019:01 PAK

COMMUNAUTAIRE EU-WETGEVING/ EU-GEMEINSCHAFTSRECHT:

Electromagnetic Compatibility Directive (EMC) 2014/30/EU

Radio Equipment Directive (RED) 2014/53/EU

Reduction of Hazardous Substances (ROHS) Directive 2011/65/EU +

2015/863/EU and (EU)2017/2102