Haier ES50V-VH3(EU) Electric Water Heater Manuel utilisateur

ES50V-F1(EU)

ES80V-F1(EU)

ES100V-F1(EU)

ES50V-TF7(EU)

ES80V-TF7(EU)

ES50V-VH3(EU)

ES80V-VH3(EU)

Please read this manual carefully before use.

Please keep it properly for future reference.

This product is for home use only and should not be used for industrial or commercial purposes.

Electric Water Heater

Instruction Manual

English

1. Safety Precautions (Please Read Before Use)...........................................3-4

2. Specification - Packing List.........................................................................5-6

3. Installations.................................................................................................7-9

4. Operations.............................................................................................. 10-12

5. Cleaning and Maintenance.......................................................................... 13

6. Transportation and Storage..........................................................................13

7. Product Disposal..........................................................................................13

8. Fault Clearance............................................................................................14

Contents:

3

Actions must be

prohibited

Actions must be

performed

Actions must be

attended to

Symbolic Interpretation

Safety Preautions (Please Read Before Use)

Warning Caution

Ban

Warning

It is necessary to allow disconnection

of the appliance from the supply after

installation. The disconnection may

be achieved by having the plug

accessible or by incorporating a

switch in the fixed wiring in

accordance with the wiring rules.

If the supply cord is damaged, it must

be replaced by the manufacturer, its

service agent or similarly qualified

persons in order to avoid a hazard.

The max. inlet water pressure is

0.75MPa, and the min. inlet water

pressure is 0.05MPa.

Caution

If the water heater is not use for a

long time, please cut off the power

and drain the water storage in the

water heater.

You can refer to the below part for

how the water heater can be drained.

It is strictly forbidden to install the

water heater in an environment

where it can freeze. Freeze can

cause the container and water pipes

to break, resulting in scalding and

leak.

Ban

Do not install the water heater in

outdoor areas.

Please install the water heater on a

solid, sturdy wall.

The appliance is intended to be

permanently connected to the

water mains and not connected by

a hose-set.

A discharge pipe connected to the

pressure-relief device (safety

valve) is to be installed in a

continuously downward direction

and in a frost-free environment.

The water may drip from the

discharge pipe of the

pressure-relief device (safety

valve) and that this pipe must be

left open to the atmosphere.

The pressure-relief device ((safety

valve) is to be operated regularly to

remove lime deposits and to verify

that it is not blocked

Ban

You can refer to the below part for

the type or characteristics of the

pressure-relief device (safety

valve) and how to connect it,

unless it is incorporated in the

appliance.

This appliance is not intended for

use by persons (including children)

with reduced physical, sensory or

mental capabilities, or lack of

experience and knowledge, unless

they have been given supervision

or instruction concerning use of the

appliance by a person responsible

for their safety.

Warning

Children shall not play with the

appliance.

Ban

English

4

Do not repair, maintain, dismantle or

modify the water heater without

professional maintenance persons.

The water may drip from the

discharge pipe of the

pressure-relief device (safety

valve) and that this pipe must be

left open to the atmosphere.

Children should be supervised to

ensure that they do not play with

the appliance.

Earthed

Use independent outlets and make

them reliably earthed.

It is strictly forbidden to use wet

hands to plug and unplug the

power supply.

If you notice any abnormality or

smell burnt odor, please immediately

cut off the powerand contact the

service center.

Check the electric meter, whether

the diameter of wire is in line with

the rated current of the water

heater, if necessary, invite a

qualified electrician to check the

wiring.

Be careful not to be scalded by hot

water.

Do not touch the valves and pipes

that supply hot water.

Please test the water temperature

with your hand before use. When the

water is at the right temperature,

then use it.

Do not use the hot water from the

water heater directly as drinking

water or for similar purposes.

Do not sprinkle water or spray

steam on the main unit of the water

heater.

Do not sprinkle water or spray

steam on the main unit of the water

heater.

Safety Preautions (Please Read Before Use)

Actions must be

prohibited

Actions must be

performed

Actions must be

attended to

Symbolic Interpretation

Warning Caution

Ban

Warning

Ban

Caution

This appliance can be used by

children aged from 3 years and

above and persons with reduced

physical, sensory or mental

capabilities or lack of experience

and knowledge if they have been

given supervision or instruction

concerning use of the appliance in

a safe way and understand the

hazards involved.

Warning

In order to avoid a hazard due to

inadvertent resetting of the thermal

cut-out, this appliance must not be

supplied through an external

switching device, such as a timer, or

connected to a circuit that is

regularly switched on and off by the

utility.

Caution

The instructions for appliances

connected to the water mains by

detachable hose-sets shall state that

the new hose-sets supplied with the

appliance are to be used and that old

hose-sets should not be reused.

Caution

5

F1 Serie

External Dimensions

Front View Rear View Side View Section View

A Hot water outlet B Cold water inlet C Inner liner D Heating tube

E Temperature tube F Magnesium rod G Wall bracket

External Dimensions

c1

d1

ABa1

f1

e1

GGC C

EDED

FF

b1

TF7 Serie e1

g1

G

e1

f1

a1

c1

d1

AB

G

b1

F F

C C

E E

DD

a1(mm) b1(mm) c1(mm) d1(mm) e1(mm)

ES50V-F1(EU) 530 305 720 350 170

ES80V-F1(EU) 530 305 1046 350 170

530 305 1265 350 170

ES100V-F1(EU)

530 320 745 100 360

530 320 1070 100 360

g1(mm)

/

Model

f1(mm)

362

635

851

297

622

ES50V-TF7(EU)

ES80V-TF7(EU)

194

Note: The allowable error range of the above parameters (dimensions) is ±10%.

410 421 685 100 190-270

410 421 995 100 190-270

200

510

ES50V-VH3(EU)

ES80V-VH3(EU)

/

VH3 Serie

English

c1

A B b1 d1

C

F

ED

a1

G

e1=190

f1

e1=270

6

Electrical Schematic

Note: The allowable error range

of the above parameters

(weights) is ±10%.

Technology Datas

F1 Serie

1 1 4 1 2

TF7 Serie

/

Expansion

Bolt

(unit)

Model

Quantity Name

Packing List

Electric Water

Heater

(unit)

Expansion

hook

(unit)

Wall-mounting

frame

(unit)

Safety Valve

(unit)

Instruction

Manual

(unit)

1 1 / 1 / 2

ES50V-F1(EU) 3000W

3000W

25kg

34kg

41kg

47L

74L

97L

ES80V-TF7(EU)

ES100V-F1(EU)

ES50V-TF7(EU)

3000W

25kg

46L

ES80V-F1(EU)

3000W

33kg

77L

Rated Power Net Weight Rated CapacityModel

220-240

V~

50

Hz

0.80

MPa

75°C IPX4

Waterproof LevelRated Voltage Rated

Temperature

Rated Frequency Rated Pressure

All models

1500W 18kg

47L

ES50V-VH3(EU)

1500W 26kg

75L

ES80V-VH3(EU)

F1 Serie

Display Board

MT2

RT1

L

NPE

EH PE

RT2

MT1

N

Relay Relay

VH3 Serie

T2

EH

RT1

MT1 MT2

E

L

N

E

Display Board

Relay Relay Relay

L - Live wire (brown)

N - Neutral wire (blue)

PE/E - Ground wire (yellow and green)

MT/MT1/MT2 - Manual reset thermostat

EH - Heating tube

RT/RT1/RT2 - Sensor

Relay Display panel

L

N

E

MT

N

EH E

RT

TF7 Serie

VH3 Serie

1 1 / 1 / 2

Installations Cautions

Installations

7

When installing the water heater, it should leave a certain amount of space (at least 300mm)

to facilitate future maintenance. If the water heater is embedded in the gusset plate during

installation, the gusset plate near the maintenance cover side should be movable to facilitate

disassembling the maintenance cover during maintenance.

It should ensure that the inlet pressure of tap water is not less than 0.05MPa and the

maximum pressure does not exceed 0.75MPa.

Electric water heater should be installed indoors, where the ambient temperature is above

0°C. The pipeline should be centrally arranged. The hot water outlet should not be too far

from the use place of hot water. If it exceeds eight meters, the hot water pipeline should be

insulated to reduce the heat loss.

The wall where the water heater is hung should be sturdy and secure to withstand four times

the weight of the water heater after filling with water. If it is a non-bearing wall or hollow brick

wall, it is necessary to take appropriate protective measures, add brackets, use crossing

screws, and install back boards.

The installation location of the electric water heater should be selected a place that is

convenient to use, maintain and have a floor drain. If the water tank or water pipe leaks, it

will not cause damage to nearby or lower level facilities. The installation position try to avoid

installing on the toilet, bathtub, washbasin and door frame. So that it does not create a

feeling of overwhelming or insecurity for the user.

Do not reverse the inlet and outlet pipes. The safety valve should be installed in the

designated position and should not be altered privately. The pressure relief hole of safety

valve should be kept in contact with atmosphere. Do not block it.

For security, water heaters should use independent sockets (multifunctional sockets are

prohibited) and be reliably earthed. And the quality of the socket should be in line with local

national standards. It is strictly forbidden to use the water heater without reliable earthed.

The power outlet of the water heater should be placed in a dry place where water cannot

shower, so as not to affect the normal work of the machine (preferably with a waterproof

box).

Use an electroprobe to measure whether the live wire and neutral wire are connected in

reverse. After confirming that the machine has been filled with water, the joints do not leak

and the power supply meets the requirements, then it can be heated by electricity.

For avoiding the danger of accidental reset of the over-temperature thermostat, the water

heater must not be powered by external switching devices such as timers. It shall not be

connected to a circuit that is frequently switched on and off through other settings.

In order to prevent the occurrence of accidents, the accessories provided by our company

must be installed and must not be replaced or substituted by yourself. If the accessories are

damaged, it must be notified to our Maintenance Department for repair and replacement

with the accessories provided by our company. If the above matters are not complied with,

we will not be responsible for any direct or indirect loss caused by the accident.

English

360mm

8

Figure 2

Figure 1 Installation Schematic - Vertical Installation

(F1/TF7/VH3 Series)

Installation Methods

f1

ES50V-TF7(EU)

297mm 622mm

Figure 5

ES80V-TF7(EU)

Figure 4 Installation Schematic - Horizontal Installation(for TF7 Series only)

It must be installed according to the schematic

Model

a 170 mm 170 mm 170 mm

b

c

ES50V-F1(EU) ES80V-F1(EU) ES100V-F1(EU)

88 mm 88 mm 88 mm

362 mm 635 mm 851 mm

Safety valve

Nozzle

Water mixing

valve

Cold water inlet

Hot water outlet

Cold water

valve

Hot water

valve

Safety valve

Nozzle

Cold water inlet

Hot water outlet

Water mixing

valve

It must be installed by the installer belonging to the After-sales Service Department of our company

or by its designated installer. For the installation of the water heater by personnel not recognized

by our company or the use of self-provided installation materials, which results in the

consequences, including but not limited to pipeline leakage, crash, poor installation affecting the

normal operation and performance of the water heater, and adverse effects or damage to the body

of the water heater. The company will not be responsible for any losses incurred as a result.

The water heater uses wall-mounted installation.

For the F1 Serie, the installation method is as follows:

Refer to Figure 1 of the Installation Schematic, and drill four holes in the wall using an percussion

drill to match the accessory expansion hook according to the dimensions shown in Figure 2 and

the table below.

1.

Insert the expansion bolts into the wall-mounting frame first, then fix them together in the wall

holes, and finally hang the water heater onto the wall-mounting frame.

Model

2.

Install the safety valve and other accessories with reference to the "Installation of Safety Valve"

(for installation reference only). Be careful to add thread seal tape seal to prevent water leakage.

3.

Cold water

valve

Hot water

valve

190mm

270mm

Figure 3

TF7 Serie

VH3 Serie

9

Pressure relief hole connects

to drain pipe

Installation of Safety Valve

Figure 6

For TF7/VH3 Series, the vertical installation method is as follows:

Refer to Figure 1 of the Installation Schematic, and drill two holes in the wall using an

percussion drill to match the accessory expansion hook according to the dimensions shown

in Figure 3.

1.

Insert the expansion hook into the wall hole and fix it, then hang the water heater onto the

hook.

2.

Install the safety valve and other accessories with reference to the "Installation of Safety

Valve" (for installation reference only). Be careful to add thread seal tape seal to prevent

water leakage.

3.

For TF7 Serie, the horizontal installation method is as follows:

Refer to Figure 4 of the Installation Schematic, and drill two holes in the wall with an

percussion drill to match the accessory expansion hook according to the dimensions shown

in Figure 5.

1.

Insert the expansion hook into the wall hole and fix it, then hang the water heater onto the

hook.

2.

Install the safety valve and other accessories with reference to the "Installation of Safety

Valve" (for installation reference only). Be careful to add thread seal tape seal to prevent

water leakage.

3.

In order to facilitate the installation and disassembly of the water heater, it is recommended

that the water heater inlet and outlet pipes are installed at the appropriate location with G1/2

loose joints respectively. Determine the location of the water supply. Connect the water inlet

pipe and the tap pipe to the water place respectively. Fill the inner tank with water, check

whether the water line is leaking. If there is a leak, it needs to be reconnected.

Warning: It is important to make sure that the hooks on the back of the machine (F1 Serie) or

the wall bracket (TF7/VH3 Series) are securely hung on the wall-mounting frame (F1 Serie) or

expansion hook (TF7/VH3 Series) before releasing the hands to prevent the water heater

from falling and causing personal injury or property damage.

Install the safety valve (its connection is G1/2) with a rated

pressure of 0.80MPa in the direction of the arrow on the safety

valve (arrow pointing to the water heater) to the inlet pipe. When

the water heater is heated by electricity, the water inside the tank

is heated and expands. In order to reduce the water pressure

inside the tank, a small amount of water droplets will flow from the

pressure relief hole of the safety valve. The pressure relief hole

should be kept open to the atmosphere and should not be

blocked.

The pressure relief hole of the safety valve can be connected to

the drain pipe. The installation method of the drain pipe of the

safety valve is as follows: Screw the one end of the drain pipe to

the pressure relief hole of the safety valve. The drain pipe

connected to the safety valve should be kept inclined installed in

a frost-free environment in a continuous downward way, and the

water overflowing from the drain pipe should drain into the floor

drain.

Note: Drain pipes are sold separately.

English

kW

F1 Serie

10

Operations

Introduction of Control Panel

Operations

Enter the bath separately

mode/ Choose the number

of bath separately

1.5kW

3kW

Display icon of the

number of bath separately

Heating icon

After installation, because of the inner tank without water, you must open the inlet valve of tap water

and outlet of water heater for the first time. The water mixing valve must be adjusted to the maximum

hot water gear, and the water outlet shall be closed after the nozzle or other water outlets continu-

ously discharge water (it means that the water in the container is full at this time). Check and turn on

the power supply when there is no water leakage at each interface.

After the water heater is powered on for the first time and the display screen is fully displayed for 1s,

it enters the state before turning on the power.

Icon Introduction

Button Introduction

Double tanks mode icon

Single tank mode icon

Set temperature /

actual temperature icon

Bacteriostatic function icon

Enter single tank mode

Enter double tanks mode

BPS bacteriostatic mode button

Power-on/Power-off

Single / Double Tank(s) Mode (F1 Serie)

Press the "1.5kW" button, and then the icon "Half" will be illumed. After the default maximum

heating temperature 75ºC. flashing for 2s, the actual water temperature will be displayed. And

the machine uses 1500W power to heat the water in the left tank.

Press the "3kW" button, and the icon "All" will be illumed. And the machine uses 3000W power

to heat the water in both tanks at the same time.

ECO

MAX

SET

MAX mode button

ECO mode button

Set temperature button

ECO mode icon

MAX mode icon

TF7 Serie

Button Introduction

BPS bacteriostatic mode button

Heating icon

Set temperature/

actual temperature icon

Bacteriostatic function icon

Icon Introduction

Power-on/ Power off

MAX

ECO

BPS

SET

Function select button

Button Introduction

Set temperature button

Power-on/Power-off

ECO mode icon

Icon Introduction

Bacteriostatic function icon

Set temperature /

actual temperature icon

Indicator light of remaining

hot water

ECO

BPS

VH3 Serie

Power-on

Plug in the power supply, and the display screen will be fully displayed for 1s, entering the

state before power-off.

Press the « » button to power on.

11

Bath Separately Mode (F1 Serie)

Press the "Smart" button to choose the number of bath separately at one time. The number

of bath separately at one time will be switched circularly between 1, 2 and 3.

Digital 1 is illumed: It is suitable for 1 person to take a bath.

Digital 2 is illumed: It is suitable for 2 persons to take a bath.

Digital 3 is illumed: It is suitable for 3 persons to take a bath.

The machine will automatically complete the heating according to the number of bathing

people you choose.

50L water can be set to bath for 1 person and 2 persons.

80L / 100L water can be set to bath for 1 person, 2 persons and 3 persons.

BPS Bacteriostatic Mode

(F1/TF7/VH3 Series)

Press the "BPS" / « » button, entering the bacteriostatic mode and illuming the correspond-

ing icon « » / « » /« BPS- » . After the default maximum heating temperature flashes for

a few seconds (80°C for F1 series and 75°C for TF7/VH3 serie), the actual water temperature

will be displayed. When the « » / « » /« BPS- » extinguishs, it indicates that the bacterio-

static function is completed, and the machine will automatically exit the BPS bacteriostatic

mode and return to the normal mode.

Press « » button again to switch to ECO-BPS-Instant heating in turn(VH3 Serie).

Normal Mode ( TF7/VH3 Series)

When the user does not choose the above modes, the machine will enter the normal mode.

In this mode, the user can adjust the setting temperature according to the demand, and the

range of setting temperature is 35-75°C. The function of heat retention is carried out after

heating.

Temperature Setting ( TF7 Serie)

In the MAX mode and ECO mode, press the "SET" button to adjust the setting temperature.

Each time the "SET" button is pressed, the setting temperature will increase by 5°C. The

adjustment range of setting temperature is 35ºC-75°C. When pressing the "SET" button to set

the temperature, the current setting temperature flashes first, and then press the "SET" button

to change the temperature. No operation within 6s or pressing other buttons except the « »

and "SET" button indicate that the setting temperature is confirmed, and then the actual

temperature is displayed.

ECO Mode (TF7/VH3 Series)

Press the "ECO" / « » button in the state of power-on, entering the ECO mode and the

corresponding icon « » / « ECO- » are illumed.

In this mode, the water heater will automatically memorize and analyze user's habits of using

water, realize intelligent operation, to meet user's water demand and save electric energy to

the most extent.

Press "ECO" button again to exit ECO mode and return to normal mode.(TF7 Serie)

Press « » button again to switch to ECO-BPS-Instant heating in turn(VH3 Serie).

This function can memorize when power off, but it will reopen the memory of user's habits of

using water.

MAX Mode ( TF7 Serie)

Press the "MAX" button in the state of power-on, entering the MAX mode and illuming the

corresponding icon « ». In this state, the two tanks are heated to the setting temperature,

and the setting temperature range is 35-75°C. After heating, the machine will automatically

exit the MAX mode and return to the normal mode.

In this mode, the double tanks are heated simultaneously, which can meet the user’s demand

of using water rapidly.

English

12

Power-off

After bathing, press the « » button to power it off.

Precautions for Use

Tip: When the water heater works in the double tanks mode, affected by the power difference

between the heating tubes of the two tanks and other factors, it is normal that the right tank is

still heating when the display screen displays 75 °C (F1/ TF7 Series).

1. Do not turn on the power supply before the water heater is filled with water, protecting the

machine from damage.

2. Adjust the water temperature to the appropriate temperature before use, preventing

scalding.

3. When there is enough hot water, turn down the set temperature as much as possible, which

can reduce heat loss, high-temperature corrosion and scaling, and prolong the service life of

the water heater.

4. Please do not put gasoline and other inflammables near the water heater, or which may

cause fire and other accidents.

Press the "ECO" / « » button in the state of power-on, entering the ECO mode and the

corresponding icon « » / « ECO- » are illumed.

In this mode, the water heater will automatically memorize and analyze user's habits of using

water, realize intelligent operation, to meet user's water demand and save electric energy to

the most extent.

Press "ECO" button again to exit ECO mode and return to normal mode.(TF7 Serie)

Press « » button again to switch to ECO-BPS-Instant heating in turn(VH3 Serie).

This function can memorize when power off, but it will reopen the memory of user's habits of

using water.

Temperature Setting ( VH3 Serie)

In the normal mode, press “+”/“-” button to adjust the setting temperature, press “+”/“-” button

for one time, « » flashes the current setting temperature for 6 times, if press “+”/“-” button

for one time every time, then the setting temperature is to increase/decrease by 5°C.

Quantity of remaining hot water ( VH3 Serie)

Under the status of switching on, the quantity of current remaining hot water can be monitored

through the icon « ».

13

Product Disposal

Transportation and Storage

Attention:

Cleaning and Maintenance

Warning: This water heater should only be repaired and maintained by qualified service personnel.

Improper methods may cause serious injury accidents or property losses.

Be sure to unplug the power plug before cleaning and maintaining the water heater.

Wipe gently with a damp cloth dipped in a small amount of neutral detergent. Do not use gasoline

or other solutions. Finally, dry it with a dry cloth to keep the water heater dry. Be careful not to scrub

with cleaners containing abrasives (including toothpaste), acids, chemical solvents (including

alcohol) or polishes.

To keep the water heater working efficiently, the heating pipe and inner tank should be cleaned

every three years. When cleaning, do not damage the protective layer on the outside of the heating

pipe and the surface of the inner tank. The warranty period of the inner tank is 7 years, and the

anode needs to be inspected once a year from the second year.

When cleaning, close the water inlet valve, open the water outlet valve, remove the safety valve at

the cold water inlet, drain the water in the water tank, and then open the water inlet valve to wash

repeatedly for several minutes until the clean water discharged from water tank.

Check the safety valve once a month: Pull the small handle of the safety valve. If there is water

flowing out, it indicates that the safety valve has worked normally. If there is no water flowing out,

please contact Haier After-sales Service Department for repair or replacement.

The safety inspection, removing the scale in heating pipe in time and replacing the magnesium rod

shall be carried out by professionals regularly.

Products must be transported and stored in accordance with the handling marks indicated on the

original packaging.

Be careful when handling and transporting.

When transportation and storage, it is must ensure that the product is protected from atmospheric

precipitation and mechanical damage.

If the electric water heater cannot be used and you want to discard it, you must

dispose it correctly in order not to damage the environment. For more

information, please contact the local service department. If the water heater is

used for scrapping, cut the power line as close to the shell as possible so that

the water heater can no longer be used.

fThe electric water heater is designed and manufactured in such a way that you

can easily handle it.

This symbol indicates that this product must not be disposed together with

household refuses. Deliver product to an collection or recycling center for

electrical or for electronic or electrical equipment.

By ensuring proper disposal of this product, you will help preventing potential

negative impacts to environmental and human health. Otherwise these effects

may be caused by improper waste disposal.

If you do not use the water heater for a long time, please close the tap water valve and open the

hot water valve of the water heater to the maximum hot water gear. At the time, please be careful

not to be scalded by hot water. And then remove the safety valve, let the water flow out of the

inner tank.

When re-using, to avoid injury accidents, it is recommended to open the hot water valve before

opening the power switch of the water heater, discharging the gas that may exist in the pipe line

from the pipe line. At the time, smoking or other open flames are not allowed near the opened

valve. Meanwhile, carefully check whether all parts of the water heater are in good condition, and

confirm that the inner tank is filled with water. Then, the water heater can be put into use.

English

Fault Clearance

No water flow out

Whether the water supply system is

cut off or the water pressure is too

low

Whether the water place is blocked

and whether the hot water valve is

opened

1. Whether the hot water outlet is

not open

2. Whether the water temperature is

adjusted properly

3. The heating time is too short and

has not been heated to the setting

temperature

4Whether the components are

damaged

Flowing cold

water

The water cannot

be heated to the

required

temperature or

the output

amount of heat

water is less

1. Is the current function mode set

correctly or the temperature set too

low

2. Is the tap water pressure too high

The water is

alternately great

and less, or

alternately cold

and hot

Is the tap water pressure stable

It fails to power

on or the display

does not work

1. Whether the power supply is in

good contact

2. Whether the components are

damaged

Display E1 Line fault

Display E2/H0

1. Is the inner tank filled with water

2. Whether the components are

damaged

1. Whether the indoor temperature

is lower than minus 20°C

2. Whether the sensors are

damaged

Display E3//E6/

E8

Check

Check and clean

Check and open

Calibrate referring to the use method in

the manual

Calibrate according to the use method

in the manual

If you have confirmed that the 123

items are not the reason, contact the

Maintenance Department

Calibrate according to the use method

in the manual

Turn down the flow of the outlet valve

for use

Turn down the flow of the outlet valve

for use or use it after the water

pressure is stable

Check the power socket

If you have confirmed that the 1 item is

not the reason, contact the

Maintenance Department

Contact the Maintenance Department

After turning off the power, fill up water

and turn on the power again

If you have confirmed that the 1 item is

not the reason, contact the

maintenance department

Cut off the power supply. When the

ambient temperature is higher than

minus 19°C, it will return to normal

after turn on the power again

If you have confirmed that the 1 item is

not the reason, contact the

Maintenance Department

SolutionsItems to be ConfirmedPhenomenons

14

English

Product fiche

Trade mark Haier

Model ES50V-TF7(EU) ES80V-TF7(EU)

Load profile

Energy efficiency class B

Energy efficiency(%) 41

Annual electricity consumption(kWh) 1251

Thermostat temperature setting(°C) 75

Sound power level indoors(dB) 15

Specific precautions Refer to the manual

Daily electricity consumption(kWh) 7.163

V40(L) 95.4

The power consumption data in the table is defined in relation to EU Directives 812/2013 and

814/2013.

The products without the label and the data sheet for water heaters and solar devices, stipulated in

regulation 812/2013, are not intended to be used in such assemblies.

This appliance is conforming with the international electrical safety standards IEC 60335-1 and IEC

60335-2-21. The CE marking of the appliances attests its conformity to the following EC Directives,

of which it satisfies the essential requisites:

- LVD Low Voltage Directive: EN 60335-1, EN 60335-2-21, EN 60529, EN 62233, EN 50106.

- EMC Electro-Magnetic Compatibility: EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3.

- RoHS2 Risk of Hazardous Substances: EN 50581.

- ErP Energy related Products: EN 50440.

M

B

41.8

1229

7.801

143.1

M

ES50V-VH3(EU) ES80V-VH3(EU)

B

39.3

1315

6.883

95.5

M

B

41.9

1300

7.343

155.1

M

Trade mark

Haier

Model

ES50V-F1(EU) ES80V-F1(EU) ES100V-F1(EU)

Load profile

M L L

Energy efficiency class

C C C

Energy efficiency(%)

36 36 37

Annual electricity consumption(kWh)

1418 2713 2749

Thermostat temperature setting(

℃

)

75

Sound power level indoors(dB)

15

Specific precautions

Refer to the manual

Daily electricity consumption(kWh)

6.645 12.562 12.755

V40(L)

67.4 138.5 168.3

ES50V-F1(EU)

ES80V-F1(EU)

ES100V-F1(EU)

ES50V-TF7(EU)

ES80V-TF7(EU)

ES50V-VH3(EU)

ES80V-VH3(EU)

Por favor, lea y comprenda el manual antes de utilizarlo.

Consérvelo adecuadamente para futuras consultas.

Este producto sólo puede ser utilizado para fines domésticos,

y no para fines industriales o comerciales.

Termo Eléctrico

Manual del Usuario

Español

1. Precauciones de Seguridad (Por favor, Lea antes de Usar)......................3-4

2. Especificaciones - Lista de embalaje..........................................................5-6

3. Instalación...................................................................................................7-9

4. Funcionamiento...................................................................................... 10-12

5. Limpieza y mantenimiento........................................................................... 13

6. Transporte y Almacenamiento......................................................................13

7. Eliminación del producto..............................................................................13

8. Solución de problemas.................................................................................14

Contenido:

3

Acciones Eliminar

prohibidas

Acciones que

deben ser

ejecutadas

Cuestiones a las

que se debe

prestar atención

Explicación de los Símbolos

Precauciones de Seguridad (Por favor, Lea antes de Usar)

Alerta Nota

Prohibición

Alerta

El apagado del dispositivo debe ser

posible después de la instalación.

El apagado puede ser llevado a cabo

mediante enchufes o interruptores

accesibles en el cableado fijo según

las normas de cableado.

Alerta

Si el cable de alimentación resulta

dañado, deberá ser sustituido por el

fabricante, su agente de servicio o

personal con la misma cualificación,

en caso de peligro.

La presión de entrada del agua del

grifo no deberá ser inferior a 0,05

MPa ni superior a 0,75 MPa.

Alerta

Nota

Si el termo no es utilizado durante

mucho tiempo, por favor corte el

suministro de energía y vacíe el agua

del termo.

El método de drenaje del termo es

mostrado a continuación.

Está estrictamente prohibido que el

termo sea instalado en un entorno en

el que es probable que haya hielo, ya

que la formación de hielo provocará

el agrietamiento del recipiente y de la

tubería de agua, ocasionando una

escaldadura y una fuga de agua.

Prohibición

El termo no debe ser instalado del

exterior.

Instale el termo en una pared sólida y

firme.

Alerta

El dispositivo debe conectarse a la

tubería de agua de forma

permanente, pero no adoptar la

conexión con el conjunto de

mangueras.

Alerta

La tubo de drenaje que se conecta

a un dispositivo de alivio de

presión (válvula de seguridad)

deberá ser instalada de forma

continua hacia abajo en un entorno

libre de congelamiento.

El agua puede salir por el tubo de

drenaje del dispositivo de alivio de

presión (válvula de seguridad), y el

tubo de drenaje deberá mantener

el acceso al exterior.

El dispositivo de alivio de presión

(válvula de seguridad) deberá ser

operado regularmente para

eliminar los sedimentos calcáreos

y confirmar que no esté

bloqueado.

Alerta

Prohibición

Las categorías o características y

los métodos de conexión del

dispositivo de alivio de presión

(válvula de seguridad) son

mostradas a continuación.

Las personas con capacidades

físicas, sensoriales o mentales

reducidas o con falta de

experiencia y conocimientos

(incluidos los niños) no deberán

utilizar este dispositivo, a menos

que estén bajo supervisión o

instrucción.

Español

4

Precauciones de Seguridad (Por favor, Lea antes de Usar)

El personal de reparación no

profesional no podrá reparar, dar

mantenimiento, desmontar o

transformar el termo a voluntad.

Prohibición Prohibición

Los niños deberán ser

supervisados para garantizar que

no jueguen con el aparato.

Los niños sin vigilancia no deberán

limpiar ni dar mantenimiento al

aparato.

Acciones Eliminar

prohibidas

Acciones que

deben ser

ejecutadas

Cuestiones a las

que se debe

prestar atención

Explicación de los Símbolos

Alerta Nota

Prohibición

Conexión

a tierra

Una toma de corriente

independiente deberá ser utilizada y

una conexión a tierra fiable deberá

estar garantizada. Prohibición

Enchufar o desenchufar la fuente

de alimentación con las manos

mojadas está estrictamente

prohibido.

Si se detecta que el termo presenta

un funcionamiento anormal, o hay

olor a quemado, por favor, corte la

corriente inmediatamente y póngase

en contacto con el Centro de

Servicio.

Compruebe si el amperímetro y el

diámetro del cable pueden

satisfacer la corriente nominal

requerida por el termo, y pida a

electricistas cualificados que

revisen el cableado cuando sea

necesario.

Alerta

Tenga cuidado y no se queme con el

agua caliente

No toque la válvula o el tubo de

suministro de agua caliente.

Pruebe la temperatura del agua

con la mano antes de usarla y

asegúrese de que es adecuada para

su uso.

No utilice el agua caliente del

termo directamente como agua

potable o para fines similares.

No rocíe agua o vapor sobre la

estructura principal del termo.

Por favor, tome medidas

preventivas cuando haga frío, en

caso de que el termo sufra daños

por congelación.

Prohibición

Alerta

Nota

La page charge ...

Haier ES50V-VH3(EU) Electric Water Heater Manuel utilisateur

Haier ES50V-VH3(EU) Electric Water Heater Manuel utilisateur

dans d''autres langues

Autres documents