Motorola IXPN4028 Safety And Operating Instructions Manual

CLP Series

Single Unit Charger (SUC)

P/N IXPN4028

en de-DE fr-FRes-ES it-IT

pt-PT

nl-NLda-DK

sv-SEfi-FInb-NO tr-TRpl-PL ru-RU uk-UA

68012002078.book Page 1 Monday, October 10, 2016 7:01 PM

68012002078.book Page 2 Monday, October 10, 2016 7:01 PM

1

English

IMPORTANT SAFETY INSTRUCTIONS

This document contains important safety and operating instructions. Please read these

instructions carefully and save them for future reference.

Before using the battery charger, read all the instructions and cautionary markings on (1) the

charger, (2) the battery and (3) on the radio using the battery.

1. To reduce the risk of injury, charge only the rechargeable Motorola Solutions authorised

batteries listed in this document. Other batteries may explode, causing personal injury and

damage.

2. Use of accessories not recommended by Motorola Solutions may result in risk of fire, electric

shock or injury.

3. To reduce the risk of damage to the electric plug and cord, pull by the plug rather than the

cord when disconnecting the charger.

4. An extension cord should not be used unless absolutely necessary. Use of an improper

extension cord could result in risk of fire and electric shock. If an extension cord must be

used, make sure that the cord size is 18 AWG for lengths up to 6.5 feet (2.0 m) and 16 AWG

for lengths up to 9.8 feet (3.0 m).

5. To reduce the risk of fire, electric shock or injury, do not operate the charger if it has been

broken or damaged in any way. Take it to a qualified Motorola Solutions service

representative.

6. Do not disassemble the charger; it is not repairable and replacement parts are not available.

Disassembly of the charger may result in risk of electrical shock or fire.

7. To reduce the risk of electric shock, unplug the transformer from the AC outlet before

attempting any maintenance or cleaning.

032374o

WARNING

68012002078.book Page 1 Monday, October 10, 2016 7:01 PM

2

English

OPERATIONAL SAFETY GUIDELINES

• Turn the radio OFF when charging battery.

• The charger is not suitable for outdoor use. Use only in dry locations/conditions.

• Connect charger only to an appropriately fused and wired supply of the correct voltage (as specified on

the product).

• Disconnect charger from line voltage by removing main plug.

• The outlet to which this equipment is connected should be nearby and easily accessible.

• Maximum ambient temperature around the power supply equipment must not exceed 40 °C (104 °F).

• Make sure that the cord is located where it cannot be stepped on, tripped over or subjected to water,

damage or stress.

MOTOROLA SOLUTIONS AUTHORISED BATTERIES

MOTOROLA SOLUTIONS AUTHORISED POWER SUPPLIES

Kit No. Description

HKNN4013_ CLP Series High Capacity Li -Ion Battery

HKNN4014_ CLP Series Standard Li -Ion Battery

Kit No. Description

PS000042A12 CLP Series EU Power Supply Adaptor

PS000042A13 CLP Series UK Power Supply Adaptor

NNTN7880_ CLP Series SUC Tray

68012002078.book Page 2 Monday, October 10, 2016 7:01 PM

3

English

Note: When charging a battery attached to a radio, turn the radio OFF to ensure a full charge.

The radio fits in the charger when placed face down in the tray.

Charging with the Drop-in Tray Single Unit Charger (SUC)

1. Place the drop-in tray charger on a flat surface.

2. Insert the connector of the power supply into the Micro USB port on the front of the drop-in

tray charger.

3. Connect the correct power supply to a proper AC outlet.

4. Insert the radio into the tray, making sure the radio is facing down and the charging contacts on

the charger are aligned with the contacts on the radio.

Kit # P/N IXPN4028_

68012002078.book Page 3 Monday, October 10, 2016 7:01 PM

4

English

Cloning Radios using the Single Unit Charger (SUC)

1. Unplug any cables (power supply or USB cables) from the Single Unit Chargers.

2. Plug one side of the cloning cable micro connector to one Single Unit Charger. Plug the other

end to the second Single Unit Charger.

Note: During the cloning process no power is being applied to the Single Unit Charger. The batteries are not being

charged. A data communication is being established between the two radios.

3. Turn ON the “Target Radio” and place it facing down into one of the Single Unit Chargers.

4. On the “Source Radio”, power the radio following the sequence below: • Press and hold the

Push-to-Talk (PTT) and the “-”. Button simultaneously while turning the radio ON until you hear

the Cloning Tone and Double Blinking Yellow on the Smart Status Glow.

5. Place the “Source Radio” facing down in its Single Unit Charger with an Audio accessory, then

press and release Menu Button to start the cloning process.

6. After cloning is completed, the “Source Radio” sounds either a “pass” tone (cloning was

successful) or a “fail” tone (cloning process has failed). The pass tone sounds like a good key

“chirp” whereas the “fail” tone sounds similar to a “bonk” tone. (A tone is heard in no more than

5 seconds.)

Cloning Cable HKKN4026_

(Not included)

68012002078.book Page 4 Monday, October 10, 2016 7:01 PM

5

English

Once you have completed the cloning process, you should turn the radios “OFF” and “ON” to bring

them to normal user mode (exit “clone” mode).

Charging Status LEDs

On the SUC, the radio charging pocket has an LED indicator. The LED indicators are grouped into

pairs to show which charging pockets are paired. The LED is red when the battery is charging, then

it turns to green once the battery is fully charged.

ESTIMATED CHARGING TIME

CHARGER LED INDICATOR

Charger Type

Standard

Li-Ion

High Capacity Li-Ion

Single Unit

Charger

4 Hours 5.5 Hours

Status LED Status Comments

Charging Steady Red

Indication

The Charger is currently

charging.

68012002078.book Page 5 Monday, October 10, 2016 7:01 PM

6

English

RADIO LED INDICATOR

Charge

Complete

Steady Green

Indication

Battery is fully charged.

Battery

Fault

Blinking Red

Battery was faulty when

inserted. Re-seating the

battery pack can probably

correct the issue.

Status LED Status Comments

Cloning Blinking

Yellow

Cloning in progress.

Status LED Status Comments

68012002078.book Page 6 Monday, October 10, 2016 7:01 PM

7

English

Limited Warranty for Motorola Solutions Personal Communications Products Purchased

I. What Does This Warranty Cover?

• Products. Defects in materials and workmanship in wireless cellular telephones, pagers and/or

two-way radios and certain accessories that are sold with them, such as the battery, battery charger

and holster manufactured and/or sold by Motorola Solutions (Products).

• Batteries. Defects in materials and workmanship in batteries that are manufactured by Motorola

Solutions and/or sold with Products are covered by this warranty only if the fully-charged capacity

falls below 80% of rated capacity or they leak.

II. How Long Is The Period Of Coverage?

From the date the Products are purchased by the first end-user:

• Products. The warranty is for one year.

• Software. The warranty is for 90 days.

• Repairs/Replacements. The warranty is for the balance of the original warranty or for 90 days from

the date you receive it, whichever is longer.

III. Who Is Covered?

This warranty extends to the first end-user purchaser only.

IV. What Will We Do To Correct Warranty Problems?

At no charge to you, we have the option to repair or replace the Products or software that do

not conform to the warranty or to refund the Products’ purchase price. We may use functionally

equivalent reconditioned, refurbished, pre-owned or new Products or parts. No software updates

are provided.

68012002078.book Page 7 Monday, October 10, 2016 7:01 PM

8

English

V. How Can You Obtain Warranty Service or Other Information?

At no charge to you, we have the option to repair or replace the Products or software that do

not conform to the warranty or to refund the Products’ purchase price. We may use functionally

equivalent reconditioned/refurbished/pre-owned or new Products or parts. No software updates

are provided.

For product information please visit us at: www.motorolasolutions.com/governmentandenterprise.

You will receive instructions on how to ship the Products to Motorola Solutions. You must ship the

Products to us with freight, duties and insurance prepaid. Along with the Products you must include:

(a) a copy of your receipt, bill of sale or other comparable proof of purchase; (b) a written description

of the problem; (c) the name of your service provider (if this Product requires subscription service);

(d) the name and location of the installation facility (if applicable) and, most importantly; (e) your

address and telephone number. If requested, you must also return all detachable parts such as

antennas, batteries and chargers. ALWAYS RETAIN YOUR ORIGINAL PROOF OF PURCHASE.

We will ship repaired or replacement Products at our expense for the freight and insurance, but at

your expense for any duties.

VI. What This Warranty Does Not Cover

• Products that are operated in combination with ancillary or peripheral equipment or software

not furnished by Motorola Solutions for use with the Products (“ancillary equipment”) or any damage

to the Products or ancillary equipment as a result of such use. Among other things, “ancillary

equipment” includes batteries, chargers, adaptors and power supplies not manufactured or supplied

by Motorola Solutions. Any of these voids the warranty.

• Someone other than Motorola Solutions (or its authorised service centres) tests, adjusts, installs,

maintains, alters, modifies or services the Products in any way. Any of these voids the warranty.

68012002078.book Page 8 Monday, October 10, 2016 7:01 PM

9

English

• Rechargeable batteries that: (a) are charged by other than the Motorola Solutions-approved

battery charger specified for charging such batteries; (b) have any broken seals or show evidence of

tampering; (c) are used in equipment other than the Product for which they are specified; or (d) are

charged and stored at temperatures greater than 60 degrees centigrade. Any of these voids the

warranty.

• Products that have: (a) serial numbers or date tags that have been removed, altered or obliterated;

(b) board serial numbers that do not match each other, or board serial numbers that do not match

the housing; or (c) non-conforming or non-Motorola Solutions housings or parts. Any of these voids

the warranty.

• Defects or damage that result from: (a) use of the Products in a manner that is not normal or

customary; (b) improper operation or misuse; (c) accident or neglect such as dropping the Products

onto hard surfaces; (d) contact with water, rain, extreme humidity or heavy perspiration; (e) contact

with sand, dirt or the like or (f) contact with extreme heat, or spills of food or liquid.

• Physical damage to the surface of the Products, including scratches, cracks or other damage to

a display screen, lens or other externally exposed parts.

• Failure of Products that is due primarily to any communication service or signal you may subscribe

to or use with the Products.

• Coil cords that are stretched or that have any broken modular tabs.

• Products that are leased.

Flat-rate repair rates may apply to Products not covered by this warranty. To obtain information

about Products needing repairs that are not covered by this warranty, please call the telephone

number previously listed. We will provide information on repair availability, rates, methods of

payment, where to send the Products, etc.

VII. Some Other Limitations

This is Motorola Solutions’ complete warranty for the Products and states your exclusive remedies.

68012002078.book Page 9 Monday, October 10, 2016 7:01 PM

10

English

This warranty is given in lieu of all other express warranties. Implied warranties, including without

limitation, the implied warranties of merchant ability and fitness for a particular purpose, are given

only if specifically required by applicable law. Otherwise, they are specifically excluded.

No warranty is made as to coverage, availability or grade of service provided by the Products,

whether through a service provider or otherwise.

No warranty is made that the software will meet your requirements or will work in combination with

any hardware or applications software products provided by third parties, that the operation of the

software products will be uninterrupted or error free, or that all defects in the software products will

be corrected.

In no event shall Motorola Solutions be liable, whether in contract or tort (including negligence) for

damages in excess of the purchase price of the Product, or for any indirect, incidental, special or

consequential damages of any kind, or loss of revenue or profits, loss of business, loss of

information or data, or other financial loss arising out of or in connection with the ability or inability to

use the Products, to the full extent these damages may be disclaimed by law.

VIII. Patent and Software Provisions

At Motorola Solutions’ expense, we will defend you and pay costs and damages that may be finally

awarded against you, to the extent that a lawsuit is based on a claim that the Products directly

infringe a patent. Our obligation is conditioned on: (a) you notifying us promptly in writing when you

receive notice of the claim; (b) you giving us sole control of the defence of the suit and all

negotiations for its settlement or compromise; and (c) should the Products become, or in Motorola

Solutions' opinion be likely to become, the subject of a claim of infringement of a patent, you permit

us, at our option and expense, either to: procure for you the right to continue using the Products;

replace or modify them so that they become non-infringing; or grant you a credit for such Products,

as depreciated, and accept their return. The depreciation will be an equal amount per year over the

lifetime of the Products, as established by Motorola Solutions.

68012002078.book Page 10 Monday, October 10, 2016 7:01 PM

11

English

Motorola Solutions will have no liability to you with respect to any claim of patent infringement that is

based upon the combination of the Products or parts furnished under this limited warranty with

ancillary equipment, as defined in Article VI above.

This is Motorola Solutions’ entire liability with respect to infringement of patents by the Products.

Laws in certain countries preserve for Motorola Solutions and other third party software providers

certain exclusive rights for copyrighted software, such as the exclusive rights to reproduce in copies

and distribute copies of such software. The software may be copied into, used in and redistributed

with only those Products that are associated with such software. No other use, including without

limitation, disassembly or reverse engineering of such software or exercise of exclusive rights in

such software is permitted.

Some countries and other jurisdictions do not allow the exclusion or limitation of incidental or

consequential damages, or limitation on the length of an implied warranty, so the above limitations or

exclusions may not apply to you. This warranty gives you specific legal rights and you may also have

other rights, which vary from jurisdiction to jurisdiction.

Contact

Motorola Solutions EU contact address:

Motorola Solutions Germany GmbH

Am Borsigturm 130,

13507 Berlin, Germany

68012002078.book Page 11 Monday, October 10, 2016 7:01 PM

12

English

MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylised M logo are trademarks or registered trademarks

of Motorola Trademark Holdings, LLC and are used under licence.

All other trademarks are the property of their respective owners.

68012002078.book Page 12 Monday, October 10, 2016 7:01 PM

1

Dansk

VIGTIGE SIKKERHEDSINSTRUKTIONER

Dette dokument indeholder vigtige sikkerheds- og driftsinstruktioner.

Læs disse instruktioner omhyggeligt, og gem dem til senere reference.

Før du bruger batteriopladeren, skal du læse alle instruktionerne og

advarselsmarkeringerne på (1) opladeren, (2) batteriet og (3) på radioen,

som batteriet anvendes i.

1. For at reducere risikoen for personskade må du kun oplade de genopladelige batterier, som

Motorola Solutions har godkendt, og som er nævnt i dette dokument. Andre batterier kan

eksplodere og forårsage personskade og beskadigelse.

2. Brug af tilbehør, der ikke er anbefalet af Motorola Solutions, kan medføre en risiko for brand,

stød eller personskade.

3. Du kan reducere risikoen for beskadigelse af el-stikket og -ledningen ved at trække i stikket

og ikke i ledningen, når du frakobler opladeren.

4. Du bør ikke bruge en forlængerledning, medmindre det er absolut nødvendigt. Hvis du bruger

en upassende forlængerledning, kan det føre til risiko for brand og elektrisk stød. Hvis det er

nødvendigt at bruge en forlængerledning, skal du sikre, at ledningsstørrelsen er 18 AWG for

længder op til 2,0 m og 16 AWG for længder op til 3,0 m.

5. For at reducere risikoen for brand, stød eller personskade må du ikke bruge opladeren,

hvis den er gået i stykker eller er beskadiget. Bring den til en kvalificeret Motorola Solutions-

servicerepræsentant.

6. Adskil ikke opladeren; den kan ikke repareres, og der kan ikke fås reservedele til den.

Adskillelse af opladeren kan medføre risiko for stød eller brand.

7. For at reducere risikoen for stød skal du koble transformeren fra vekselstrømsbøsningen,

før du forsøger at udføre nogen form for vedligeholdelse eller rengøring.

032374o

ADVARSEL!

68012002078.book Page 1 Monday, October 10, 2016 7:01 PM

2

Dansk

RETNINGSLINJER FOR DRIFTSSIKKERHED

• Sluk radioen, mens du oplader batteriet.

• Opladeren er ikke egnet til udendørs brug. Brug den kun på tørre steder.

• Slut kun opladeren til en strømforsyning, der har korrekte sikringer, ledninger og korrekt spænding

(som specificeret på produktet).

• Kobl opladeren fra strømforsyningen ved at tage hovedstikket ud.

• Den udgang, som dette udstyr er tilsluttet, skal være i nærheden og være lettilgængeligt.

• Den maksimale omgivelsestemperatur omkring strømforsyningsudstyret må ikke overstige 40 °C.

• Sørg for, at ledningen er placeret et sted, hvor man ikke kan træde på den, falde over den, og hvor den

ikke bliver udsat for vand eller belastninger og ikke bliver beskadiget.

BATTERIER GODKENDT AF MOTOROLA SOLUTIONS

STRØMFORSYNINGER GODKENDT AF MOTOROLA SOLUTIONS

Sætnr. Beskrivelse

HKNN4013_ CLP Series-li-ion-batteri med høj kapacitet

HKNN4014_ CLP Series-li-ion-standardbatteri

Sætnr. Beskrivelse

PS000042A12 Strømforsyningsadapter til EU i CPL-serien

PS000042A13 Strømforsyningsadapter til Storbritannien i CPL-serien

NNTN7880_ CLP Series SUC-holder

68012002078.book Page 2 Monday, October 10, 2016 7:01 PM

3

Dansk

Bemærk! Ved opladning af et batteri, der er sat i en radio, skal du slukke radioen for at sikre en fuld

opladning. Radioen passer i holderen, når den placeres nedadvendt i holderen.

Opladning med isætningsopladeren til en enkelt enhed (SUC)

1. Placer isætningsopladeren på en flad overflade.

2. Sæt stikket fra strømforsyningen i Micro USB-porten på forsiden af isætningsopladeren.

3. Slut den korrekte strømforsyning til en passende jævnstrømsstikkontakt.

4. Sæt radioen i holderen, og sørg for, at radioen vender nedad, og at opladningskontakterne på

opladeren er justeret med kontakterne på radioen.

Sætnr. P/N IXPN4028_

68012002078.book Page 3 Monday, October 10, 2016 7:01 PM

4

Dansk

Kloning af radioer vha. opladeren til én enhed (SUC)

1. Frakobl alle kabler (strømforsyning eller USB-kabler) fra opladere til en enkelt enhed.

2. Slut den ene ende af kloningskablet (med mikrostikket) til en oplader til en enkelt enhed.

Slut den anden ende til den anden oplader til en enkelt enhed.

Bemærk! Under kloningsprocessen sendes ingen strøm til opladeren til en enkelt enhed. Batterierne oplades

ikke. Der oprettes en datakommunikation mellem de to radioer.

3. Tænd for ”målradioen”, og placer den nedadvendt i én af opladerne til en enkelt enhed.

4. På ”kilderadioen” skal du tænde radioen ved at følge nedenstående sekvens: • Tryk og hold

på PTT (Push-to-Talk) og knappen ”-” samtidigt, mens du tænder radioen, indtil du hører

kloningstonen og ser den blinkende, dobbelte gule på den smarte statusindikator.

5. Placer ”kilderadioen” nedadvendt i opladeren til en enkelt enhed med et lydtilbehør, og tryk

og slip derefter knappen Menu for at starte kloningen.

6. Når kloningen er gennemført, afspiller ”kilderadioen” enten en ”bestået”-tone (kloningen

lykkedes) eller en ”fejl”-tone (kloningen mislykkedes). Bestået-tonen lyder som en ”kvidrelyd”,

mens ”fejl”-tonen lyder som en ”dump” lyd. (Der lyder en tone i maksimalt fem sekunder).

Kloningskabel HKKN4026_

(ikke inkluderet)

68012002078.book Page 4 Monday, October 10, 2016 7:01 PM

5

Dansk

Når du har gennemført kloningsprocessen, skal du slukke og tænde radioerne for at stille dem

i normal brugertilstand (afslut kloningstilstanden).

LED-indikatorer for opladningsstatus

På SUC-enheden har radioopladningspladsen en LED-indikator. LED-indikatorerne er grupperet

i par for at vise, hvilke opladningspladser er parrede. LED-indikatoren er rød, når batteriet lades op,

og skifter så til grøn, når batteriet er fuldt opladet.

ANSLÅET OPLADNINGSTID

Opladertype

Standard

li-ion

Li-ion med høj

kapacitet

Oplader til en

enkelt enhed

4 timer 5,5 timer

68012002078.book Page 5 Monday, October 10, 2016 7:01 PM

6

Dansk

LED-INDIKATOR FOR OPLADER

LED-INDIKATOR FOR RADIO

Status LED for status Kommentarer

Opladning

Konstant

rød

indikation

Opladeren lader i øjeblikket op.

Opladning

fuldført

Konstant

grøn

indikation

Batteriet er fuldt opladet.

Fejl

i batteri

Blinker

rødt

Batteriet var fejlbehæftet ved

isætning. Problemet kan ofte

løses ved at udtage batteripakken

og sætte den i igen.

Status LED for status Kommentarer

Kloning

Blinker

gult

Kloning i gang.

68012002078.book Page 6 Monday, October 10, 2016 7:01 PM

La page charge ...

Motorola IXPN4028 Safety And Operating Instructions Manual

Ce manuel convient également à

Motorola IXPN4028 Safety And Operating Instructions Manual

dans d''autres langues

Documents connexes

Autres documents