Best IPP9E42SB Guide d'installation

In USA - BEST Hartford, Wisconsin

In CANADA - BEST Drummondville, QC, Canada

Model IPP9

ENGLISH........................................3

FRANÇAIS...................................21

ESPAÑOL.....................................41

REGISTER YOUR PRODUCT ONLINE AT : www.BestRangeHoods.com/register

For additional Information visit www.BestRangeHoods.com

- 3 -

READ AND SAVE THESE INSTRUCTIONS

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE

THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the

manufacturer at the address or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service panel and lock service panel to

prevent power from being switched on accidentally. When the service disconnecting means cannot

be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by a qualified person(s) in accordance with all

applicable codes and standards, including fire-rated construction codes and standards.

4. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney)

of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturer’s

guidelines and safety standards such as those published by the National Fire Protection Associa-

tion (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

5. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. Do not use this unit with any separate solid-state speed control device.

8. To reduce the risk of fire, use only steel ductwork.

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk

of electrical shock by providing an escape wire for the electric current.

WARNING - Improper grounding can result in a risk of electric shock.

Consult a qualified electrician if the grounding instructions are not completely understood, or if doubt

exists as to whether the appliance is properly grounded.

Do not use an extension cord. Have a qualified electrician install an outlet near the appliance.

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

A. Never leave surface units unattended at high settings. Boilovers cause smoking and greasy

spillovers that may ignite. Heat oils slowly on low or medium settings.

B. Always turn hood ON when cooking at high heat or when flambeing food (i.e. Crepes Suzette,

Cherries Jubilee, Peppercorn Beef Flambe’).

C. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter.

D. Use proper pan size. Always use cookware appropriate for the size of the surface element.

!

INTENDED FOR DOMESTIC COOKING ONLY

!

- 4 -

WARNING

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE

FIRE, OBSERVE THE FOLLOWING:*

1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE

CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL

THE FIRE DEPARTMENT.

2. NEVER PICK UP A FLAMING PAN - You may be burned.

3. DO NOT USE WATER, including wet dishcloths or towels - violent steam explosion will result.

4. Use an extinguisher ONLY if:

A. You know you have a Class ABC extinguisher and you already know how to operate it.

B. The fire is small and contained in the area where it started.

C. The fire department is being called.

D. You can fight the fire with your back to an exit.

* Based on “Kitchen Fire Safety Tips” published by NFPA.

!

CAUTION

1. For indoor use only.

2. To reduce risk of fire and to properly exhaust air, be sure to duct air outside. Do not vent exhaust

air into spaces within walls or ceilings or into attics, crawl spaces, or garages.

3. Take care when using cleaning agents or detergents.

4. Avoid using food products that produce flames under the Range Hood.

5. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and

vapors.

6. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray,

construction dust, etc. off power unit.

7. Your hood motor has a thermal overload which will automatically shut off the motor if it becomes

overheated. The motor will restart when it cools down. If the motor continues to shut off and restart,

have the hood serviced.

8. For best capture of cooking impurities, the bottom of the hood should be a minimum of 24" and a

maximum of 36" above the cooking surface.

9. Two installers are recommended because of the large size and weight of this hood.

10. This product is equipped with a thermostat which may start blower automatically. To reduce the

risk of injury and to prevent power from being switched on accidentally, switch power off at service

panel and lock or tag service panel.

11. Please read specification label on product for further information and requirements.

12. EXTERNAL BLOWER MODELS ONLY: To reduce risk of fire and electric shock, install this range

hood only with Best Exterior Blower Models EB6, EB9, EB12 or EB15 or Best In-Line Blower

Models ILB3, ILB6, ILB9 or ILB11. Other blowers cannot be substituited. (Blower sold separately)

- 5 -

CLEANING AND MAINTENANCE

Proper maintenance of the Range Hood will assure proper performance of the unit.

Motor

The motor is permanently lubricated and never needs oiling. If the motor bearings make

excessive or unusual noise, replace the motor with the exact service motor. The impeller

should also be replaced.

Grease Filter

The grease filters should be cleaned frequently. Use a warm detergent solution. Grease

filter are dishwasher safe.

Clean all-metal filters in the dishwasher using a non-phosphate detergent. Discoloration

of the filter may occur if using phosphate detergents, or as a result of local water

conditions - but this will not affect filter performance. This discoloration is not covered by

the warranty. See “INSTALL FILTERS” section for removal and installation instructions.

Drip Tray

The drip tray should be cleaned once a month or

as needed. To remove the drip tray, first remove

the baffle grease filters. Grasp both ends of the

drip tray. Gently lift the drip tray up until the bottom

of it clears the track. Pull the drip tray forward,

being careful not to spill the contents, and move it

to a nearby trash receptacle. To clean the drip tray,

drain and wipe all excess grease with a dry paper

towel. Wash with warm soapy water or in the

dishwasher. Dry with a clean cloth. To replace the

drip tray, lift it up and into the track on the hood.

Reinstall baffle grease filters.

Stainless Steel Cleaning

DO:

• Regularly wash with clean cloth or rag

soaked with warm water and mild soap or

liquid dish detergent.

• Always clean in the direction of original

polish lines.

• Always rinse well with clear water (2 or 3

times) after cleaning. Wipe dry completely.

• You may also use a specialized

household stainless steel cleaner.

DON’T:

• Use any steel or stainless steel wool or

any other scrapers to remove stubborn dirt.

• Use any harsh or abrasive cleansers.

• Allow dirt to accumulate.

• Let plaster dust or any other construction

residues reach the hood. During

construction/renovation, cover the range

hood to make sure no dust sticks to the

stainless steel surface.

Avoid: When choosing a detergent

• Any cleaners that contain bleach will attack stainless steel

• Any products containing: chloride, fluoride, iodide, bromide will deteriorate surfaces rapidly.

• Any combustible products used for cleaning such as acetone, alcohol, ether, benzol,

etc., are highly explosive and should never be used close to a range.

- 6 -

OPERATION

A

C

B

D R

Button A = turns the lights on/low/high/off.

Button B = Activates/Deactivates the delay-off feature. Press once (when blower is on) to

activate the delay-off feature. The selected speed level that is displayed in display “C” will

blink when this feature is activated. After 10 minutes, the blower will then turn off. Delay

can be deactivated at any time by pressing the button again.

Display C = Indicates the selected speed of the blower 1, 2, 3, or b for boost.

“-” indicates the need to clean the grease filter or replace the non-duct filter.

Button D = Turns on the blower. Hood will turn on to the last speed selected. The blower

speed will change each time the button is pushed (from 1 to “b”). To turn the blower off,

press and hold button for approximately 2 seconds.

Button R = Filter clean indicator reset. Press and hold for 2 seconds to reset the indicator.

Auto Shut-Off Feature

If the blower and/or the lights are on continuously for 10 hours without any user interaction

with the controls, the hood will automatically shut off. Press any control button to re-activate

the hood.

HEAT SENTRY™

Your hood is equipped with a HEAT SENTRY™ thermostat. This thermostat is a device that

will turn on or speed up the blower if it senses excessive heat above the cooking surface.

1) If blower is OFF - it turns blower ON to HIGH speed.

2) If blower is ON at a lower speed setting - it turns blower up to HIGH speed.

When the temperature level drops to normal, the blower will return to its original setting.

WARNING

The HEAT SENTRY thermostat can start the blower even if the hood is turned OFF.

When this occurs, it is impossible to turn the blower OFF with its switch. If you must

stop the blower, do it from the main electrical panel.

Controls (Fig.1)

HALOGEN BULBS

This range hood requires 4 halogen bulbs (based

on size of hood) (Type T4, 120 Volt, 25 Watt Max, G9

Base).

WARNING: Always switch off the electrical

supply before carrying out any operation on the

appliance.

To change bulbs:

1. Open the cover by gently prying from proper slots

(Fig.2).

2. Remove the bulb by pulling sideways (DO NOT

ROTATE).

CAUTION: Bulb may be hot.

3. Replace with Type T4, 120 Volt, 25 Watt Max, G9 Base halogen bulbs. Do not touch

replacement bulbs with bare hands!

!

FIG. 2

- 7 -

PREPARE THE HOOD

Unpack hood and check contents.

You should receive:

1 - Hood

1 - Decorative Flues

1 - Support Frame

1 - Parts Bag (B080810996) containing:

24 - Mounting Screws (3,9 x 9,5mm Pan Head)

6 - Mounting Lag Screws (6 x 60mm)

4 - Mounting Screws (M5 x 20mm Pan Head)

4 - Washers ø 5,2x15mm

1 - Duct Collar

1 - Installation Instructions

DUCT COLLAR

4 MOUNTING SCREWS

(M5x20mm Pan Head)

DECORATIVE

FLUES

24 MOUNTING

SCREWS (3,9x9,5mm

Pan Head)

6 MOUNTING LAG

SCREWS (6x60mm)

FIG. 3

4 WASHERS

Ø 5,2x15mm

SUPPORT

FRAME

- 8 -

EXTERIOR AND IN-LINE BLOWER SELECTION IPP9E Series

CAUTION: To reduce risk of fire and electric shock, install this range hood only with Best

Exterior Blower Models EB6, EB9, EB12 or EB15, and Best In-Line Blower Models ILB3, ILB6,

ILB9 or ILB11. Other blowers cannot be substituited.

The blower must be UL listed for Canadian and U.S. use, and evaluated for use with solid state

speed control, rated 120V, 60 Hz, 6.0 A max.

INSTALL THE DUCTWORK IPP9E Series

NOTE: To reduce the risk of fire, use only metal ductwork.

1. Choose the location where the Exterior Blower or In-Line Blower will be mounted. See

illustrations below for mounting location suggestions and restrictions.

2. A straight, short duct run will allow the hood to perform most efficiently.

3. Long duct runs, elbows and transitions will reduce the performance of the hood. Use as

few of them as possible. Larger ducting may be required for best performance with long

duct runs.

4. After the Exterior or In-Line Blower has been installed, connect round metal ductwork

and work back towards the hood location. Use duct tape to seal joints between ductwork

sections.

10”ROUND

DUCT

24” TO 36” ABOVE

COOKING SURFACE

DECORATIVE

FLUE

10” ROUND

DUCT

EXTERIOR

BLOWER

HOOD

OK

SUGGESTED MOUNTING LOCATIONS

EXTERIOR BLOWER

CAUTION: MAY NOT FIT

UNDER EAVES OF SINGLE

STORY HOMES

FIG. 4

- 9 -

IN-LINE BLOWER

FIG. 5

INSTALL THE DUCTWORK

IPP9IQ Series

WARNING: To reduce the risk of fire, use

only metal ductwork.

1. Decide where the ductwork will run

between the hood and the outside.

2. A straight, short duct run will allow the hood

to perform most efficiently.

3. Long duct runs, elbows, and transitions will

reduce the performance of the hood. Use

as few of them as possible.

4. Install a roof or wall cap. Connect 10" round

metal ductwork to cap and work back

towards hood location. Use duct tape to

seal the joints between ductwork sections.

ROOF CAP

10” ROUND

ELBOW

24” TO 36” ABOVE

COOKING SURFACE

10” ROUND

DUCT

DECORATIVE

FLUE

HOOD

- 10 -

INSTALL SUPPORT SYSTEM

1. At hood location, install 2 x 4 or larger cross

framing between ceiling joists using

dimensions shown.

2. Finish the ceiling surface. Be sure to mark

the location of the ceiling joists and cross

framing.

3. Adjust the overall height using the chart below

of the support frame. Loosen and re-tighten

the 4 screws in the height adjustment slots

as necessary. Insert 12 screws (3.9x9.5mm)

located in the Hardware Package (Fig.6)

make sure this a 4” min. overlap between the

upper and lower support legs.

4. Mount the four 6x70mm screws to ceiling in

the location shown in figure 7. Allow 1/4”

clearance between screw head and ceiling

(screws will be tightened later). Make sure

the screws are driven into the center of joists

and framing for maximum strength.

Notes:

a. “-” = Mounting height is not possible.

b. Minimum hood distance above cook top

must not be less than 24”. A maximum of

36” above cook top is highly recommended

for best capture of cooking impurities.

Distances over 36” are at the installer and

the users discretion; and if ceiling height

and flue lenght permit.

c. Requires optional 10’ flue extension,

ducted model AEIPP9SB.

TOP VIEW OF SUPPORT FRAME

10

3

/16” (260mm)

11

7

/16”

(290mm)

CEILING

JOISTS

CROSS FRAMING

SUPPORT

FRAME

10

3

/16”

DRYWALL

MOUNTING

SCREWS

(6x70mm)

HEIGHT ADJUSTMENT

SLOTS

==

11” (280mm)

Ceiling

Height

Hood Distance Above 36” High Cook Top (in.) (see note b)

8 Feet

24

3

/4”

10 Feet

(see note c)

11 Feet

(see note c)

9 Feet

FIG. 6

FIG. 7

MOUNTING

SCREWS

3,9x9,5mm

23

3

/4”22

3

/4”21

3

/4”- - - - - - - - -

---33

3

/4”32

3

/4”31

3

/4”30

3

/4”29

3

/4”28

3

/4”27

3

/4”26

3

/4”25

3

/4”24

3

/4”

48

3

/4”47

3

/4”46

3

/4”45

3

/4”44

3

/4”43

3

/4”42

3

/4”41

3

/4”40

3

/4”39

3

/4”38

3

/4”- -

----56

3

/4”55

3

/4”54

3

/4”53

3

/4”52

3

/4”51

3

/16”50

3

/4”49

3

/4”48

3

/4”

24

25 26 28 29 30 31 32 33 34 35 36 27

Assembled Support Frame Height (in.)

- 11 -

5. Adjust the overall height of the support

frame. Loosen and re-tighten the 4 screws

in the height adjustment slots as

necessary. Insert 8 screws (3.9x9.5mm), 4

screws (M5x20mm) and 4 washers

(D.5.2x15mm) located in the Hardware

Package (Fig. 8).

CONNECT DECORATIVE FLUE

DUCTED INSTALLATION ONLY

Note: Rooms with 10 or 11 foot ceilings

require flue extension model AEIPP9SB,

available from your local dealer. Discard

the upper flue supplied with the range

hood and replace it with the longer flue

extension.

1. Insert the upper flue and lower flue in the

support frame (Fig.9).

2. Mount the hood to the ceiling using the (4)

previously installed 6x70mm screws.

Tighten these screws. Install (2) additional

6x70mm screws as shown in the

illustration. Make sure all (6) screws are

secure.

3. Secure the hood to the ceiling and install

the (2) additional screws (6x70mm).

4. Fix the duct connector onto the hood using

2 screws (3.9x9.5mm) located in the

Hardware Package (Fig.10).

3. Use 10" round metal duct to connect the

duct collar on the hood to the ductwork

above (Fig.11).

4. Use duct tape to make all joints secure and

air tight.

WASHERS

Ø 5,2x15mm

MOUNTING

SCREWS

3,9x9,5mm

MOUNTING SCREWS M5x20mm

MOUNTING

SCREWS

3,9x9,5mm

FIG.8

FIG. 9

FIG.10

MOUNTING

SCREWS

3,9x9,5mm

FIG. 11

10” ROUND

METAL DUCT

- 12 -

WIRING (IPP9IQT)

Note: This range hood must be properly

grounded. The unit should be installed by a

qualified electrician in accordance with all

applicable national and local electrical

codes.

1. Remove the wiring box cover. Remove a

knockout from the wiring box (Fig.12).

2. Secure the conduit to the wiring box through

a conduit connector.

3. Make electrical connections. Connect white

to white, black to black and green to green.

4. Replace wiring box cover and screws.

Make sure that wires are not pinched

between cover and box.

ADDITIONAL EXTERNAL

BLOWER WIRING (IPP9E)

1. Run 2-wire plus ground power cable from

the exterior blower to the hood’s wiring box

marked “motor connection” (Fig.13).

2. Remove the cover from the wiring box and

remove one knockout.

3. Feed 6” of cable through the knockout

opening and secure the cable to the wiring

box with an appropriate connector.

4. Make electrical connections at the hood.

Connect white-to-white, red-to-black and

green-to-ground.

5. Replace the wiring box cover and screws.

Make sure wires are not pinched between

the cover and box.

Exterior blower connection:

1. Make electrical connections at the exterior

blower (see instructions provided with the

exterior blower).

Once wiring operations are complete,

remove tape and slide down the lower flue .

CONNECT DECORATIVE FLUE

1. Attach the upper flue to the upper

support frame with the mounting screws

3,9x9,5mm (Fig.14).

2. Lower the lower flue in place.

WIRING BOX

COVER

EXTERIOR BLOWER

BLOWER CONNECTION AT HOOD

BOX MARKED

“MOTOR

CONNECTION”

CONNECT:

WHITE-TO-WHITE,

RED-TO-BLACK,

GREEN-TO-GROUND.

FIG.13

FIG.12

FIG. 14

MOUNTING

SCREWS

3,9x9,5mm

- 13 -

INSTALL FILTERS

DUCTED HOODS

NOTE: Prior to use, remove protective film

from the filter frame.

1.To remove the GREASE filter, (Fig.15) push

the filter towards the front so that it clears the

filter channel, then pull down on the handle

to disengage the filter from the hood. Tilt the

filter downward and remove.

2.The grease filters and the drip tray (see

page 5 for removal & cleaning instructions)

should be cleaned frequently. Use a warm

detergent solution. Grease filters and the oil

collectors are dishwasher safe.

3.To install the GREASE filter, align rear filter

tabs with spring in the hood. Pull down

handle, push filter into position and release.

Make sure the filter is securely engaged

after installation.

FIG. 15

- 14 -

CALIBRATE IQ BLOWER SYSTEM

TM

Ducted Internal Blower Hoods Only

After the hood is installed and wired, engage the calibration process (our Guaranteed

Performance System Technology) to ensure full-rated airflow is being delivered. Prior to

calibration, ensure that all filters, light bulbs and duct system components are installed and

sealed.

CALIBRATION PROCESS

Hold the calibration button for 3 seconds; calibration button will light up and stay on for up to

13 minutes. The blower will start and begin the calibration process. When calibration is

complete, one of two things will occur:

A.The blower turns off and calibration button light turns off = Successful calibration.

B.The blower turns off and calibration button light blinks continuously = Too much restriction

in the ductwork is preventing the IQ Blower System

TM

from achieving the rated airflow. The

blower is automatically set to maximum intensity.

Note: Common items that cause restrictions: restricted damper flap (backdraft damper, wall

cap, roof cap), too many elbows, duct size less than 80% of hood outlet, poor transition,

use of flex ducting and/or crushed ducting.

Two options are available:

1.Press the calibration button to accept airflow as is. The IQ Blower System

TM

is now configured

to its highest possible setting. The blinking calibration light goes out.

2.Correct duct restriction and repeat the calibration process.

a. To clear the original calibration data, hold calibration button for 10 seconds. The light

will blink 3 times to confirm and the blower configuration will go back to default settings.

b. Repeat calibration process.

CALIBRATION LIGHT

CALIBRATION

BUTTON

- 15 -

WARRANTY

ONE YEAR LIMITED WARRANTY FOR BEST PRODUCTS

Broan-NuTone LLC (Broan-NuTone) warrants to the original consumer purchaser of Best products that such products will be free

from defects in materials or workmanship for a period of one year from the date of original purchase. THERE ARE NO OTHER

WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OR MERCHANT ABILITY

OR FITNESS FOR A PARTICULAR PURPOSE.

During this one-year period, Broan-NuTone will, at its option, repair or replace, without charge, any product or part which is found

to be defective under normal use and service.

THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS, TUBES, HALOGEN AND INCANDESCENT

BULBS, FUSE, FILTERS, DUCTS, ROOF CAPS, WALL CAPS AND OTHER ACCESSORIES FOR DUCTING. This warranty does

not cover (a) normal maintenance and service or (b) any products or parts which have been subject to misuse, negligence,

accident, improper maintenance or repair (other than by Broan-NuTone), faulty installation or installation contrary to recom-

mended installation instructions.

The duration of any implied warranty is limited to the one-year period as specified for the express warranty. Some states do not

allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you.

BROAN-NUTONE'S OBLIGATION TO REPAIR OR REPLACE, AT BROAN-NUTONE'S OPTION, SHALL BE THE PURCHASER'S

SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. BROAN-NUTONE SHALL NOT BE LIABLE FOR INCIDENTAL,

CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH PRODUCT USE OR PERFORMANCE.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion

may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. This warranty

supersedes all prior warranties.

To qualify for warranty service, you must (a) notify Broan-NuTone at the address stated below or telephone number stated below,

(b) give the model number and part identification and (c) describe the nature of any defect in the product or part. At the time of

requesting warranty service, you must present evidence of the original purchase date.

In USA - Best®, 926 W. State Street, Hartford, WI 53027 (800-558-1711)

In Canada - Best®, 550 Lemire Blvd., Drummondville, QC J2C 7W9 (866-737-7770)

www.BestRangeHoods.com

IPP9 Programming Mode Procedure

IPP9E Programming Mode Procedure

The range hood is designed to work with several different blowers models. Before using the

hood, the control must first be programmed to your blower model, in order to achieve proper

operating speed:

1.Find the SETUP number that corresponds to the blower model that is installed with your

range hood.

2.There must be power to the hood but the blower and lights must be turned off.

3.Push simultaneously LIGHT SWITCH and RESET SWITCH for 5 sec: the display shows a

“P” blinking three times and then shows alternately the “P” and the setup selected.

4.Select the desired setup with BLOWER SWITCH (3

Î2Î1) or RESET SWITCH

(1

Î2Î3).

5. Push TIMER SWITCH to confirm.

6. The display (“P”) blinks two times ( 2 sec on - 0,5sec off) recording the selected setup.

SETUP 1

SETUP 2

SETUP 3

EB6

ILB3

ILB6

EB12

EB15

ILB9

EB9

ILB11

Description of “Speed Level”

Setup 1 is for motors with a rating up to 3.0 amp

Setup 2 is for motors with a rating between 3.1 amp and 5.0 amp

Setup 3 is for motors with a rating greater than 5.1 amp

- 16 -

KEY NO. PART NO. DESCRIPTION

9 B08087951 Grease Filters

17 BE3351864 Light Diffuser Support

37 B02300804 Heat Sentry

67 B06102599 Wires Assembly

115 BE3350233 Wiring Box

116 BE3334252 Wiring Box Cover

124 B08093422 Telescopic Structure Bottom

125 B08093456 Telescopic Structure Top

130 BE3405184 Front Trim

135 BE3405178 Trim Back

195 BE3351870 Filter Spacers

202 B03292290 Wire Clamp

274 B03295035 Fuse Box

415 B03292596 Fairlead

439 B02320034 Grommet

474 B02300918 Halogen Lamp

477 BE3351866 Light Diffuser Support Back

485 B08016370 Decorative Flue Assembly

506 97019432 BLDC Driver

507 B06102584 Calibration Button Assembly

AQI B06102600 Switch Box Assembly

ARU BE3405192 Duct Connector Assembly 10”

IME B06145225 Electrical Installation Assembly

CAS B06002259 Blower Assembly

* B080810996 Fitting Set (Includes Key No. ARU)

* Not shown assembled.

SERVICE PARTS

MODEL IPP9IQT

- 17 -

- 18 -

KEY NO. PART NO. DESCRIPTION

9 B08087951 Grease Filters

17 BE3351864 Light Diffuser Support

37 B02300804 Heat Sentry

67 B06102608 Wires Assembly

115 BE3350233 Wiring Box

116 BE3334252 Wiring Box Cover

124 B08093422 Telescopic Structure Bottom

125 B08093456 Telescopic Structure Top

130 BE3405184 Front Trim

135 BE3405178 Trim Back

195 BE3351870 Filter Spacers

202 B03292290 Wire Clamp

274 B03295035 Fuse Box

415 B03292596 Fairlead

474 B02300918 Halogen Lamp

477 BE3351866 Light Diffuser Support Back

485 B08016370 Decorative Flue Assembly

AQI B06102607 Switch Box Assembly

ARU BE3405192 Duct Connector Assembly 10”

IME B06145226 Electrical Installation Assembly

* B080810996 Fitting Set (Includes Key No. ARU)

* Not shown assembled.

SERVICE PARTS

MODEL IPP9E

- 19 -

- 20 -

La page charge ...

Best IPP9E42SB Guide d'installation

Ce manuel convient également à

Best IPP9E42SB Guide d'installation

dans d''autres langues

Documents connexes

Autres documents