THANK YOU for purchasing this high-quality product. If you should experience a problem not covered in TROUBLESHOOTING,
please visit our website at www.whirlpool.ca for additional information. If you still need assistance, call us at 1-800-807-6777.
You will need your model and serial number located on the oven frame behind the storage drawer panel.
®
GAS RANGE
USER INSTRUCTIONS
Table of Contents
RANGE SAFETY.......................................................................................2
The Anti-Tip Bracket .............................................................................3
FEATURE GUIDE .....................................................................................4
COOKTOP USE........................................................................................5
Sealed Surface Burners ........................................................................5
OVEN USE ................................................................................................6
Electronic Oven Controls......................................................................6
Aluminum Foil........................................................................................6
Positioning Racks and Bakeware.........................................................7
Oven Vent..............................................................................................7
Baking and Roasting.............................................................................7
Broiling ..................................................................................................7
Timed Cooking (on some models)........................................................8
RANGE CARE...........................................................................................8
Self-Cleaning Cycle (on some models) ................................................8
General Cleaning...................................................................................9
Oven Light.............................................................................................9
TROUBLESHOOTING............................................................................10
ACCESSORIES ......................................................................................11
WARRANTY............................................................................................12
W10196152B
2
RANGE SAFETY
You can be killed or seriously injured if you don't immediately
You
can be killed or seriously injured if you don't
follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING
WARNING: If the information in this manual is not followed exactly, a fire or explosion
may result causing property damage, personal injury or death.
– Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
– WHAT TO DO IF YOU SMELL GAS:
•
Do not try to light any appliance.
•
Do not touch any electrical switch.
•
Do not use any phone in your building.
•
Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
instructions.
•
If you cannot reach your gas supplier, call the fire department.
– Installation and service must be performed by a qualified installer, service agency or
the gas supplier.
3
The Anti-Tip Bracket
The range will not tip during normal use. However, the range can tip if you apply too much force or weight to the open door without the anti-
tip bracket fastened down properly.
Tip Over Hazard
A child or adult can tip the range and be killed.
Connect anti-tip bracket to rear range foot.
Reconnect the anti-tip bracket, if the range is moved.
See the installation instructions for details.
Failure to follow these instructions can result in death or serious burns to children and adults.
Anti-Tip Bracket
Making sure the anti-tip bracket is installed:
• Slide range forward.
• Look for the anti-tip bracket securely attached to floor.
• Slide range back so rear range foot is under anti-tip bracket.
Range Foot
WARNING
SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electrical shock, injury to
persons, or damage when using the range, follow basic
precautions, including the following:
■ WARNING:
TO REDUCE THE RISK OF TIPPING OF THE
RANGE, THE RANGE MUST BE SECURED BY PROPERLY
INSTALLED ANTI-TIP DEVICES. TO CHECK IF THE DEVICES
ARE INSTALLED PROPERLY, SLIDE RANGE FORWARD, LOOK
FOR ANTI-TIP BRACKET SECURELY ATTACHED TO FLOOR,
AND SLIDE RANGE BACK SO REAR RANGE FOOT IS UNDER
ANTI-TIP BRACKET.
■ WARNING:
NEVER use this appliance as a space heater to
heat or warm the room. Doing so may result in carbon monoxide
poisoning and overheating of the oven.
■ WARNING:
NEVER cover any slots, holes or passages in the
oven bottom or cover an entire rack with materials such as
aluminum foil. Doing so blocks air flow through the oven and may
cause carbon monoxide poisoning. Aluminum foil linings may also
trap heat, causing a fire hazard.
■ CAUTION:
Do not store items of interest to children in cabinets
above a range or on the backguard of a range – children climbing
on the range to reach items could be seriously injured.
■
Proper Installation – The range, when installed, must be electrically
grounded in accordance with local codes or, in the absence of
local codes, with the National Electrical Code, ANSI/NFPA 70. In
Canada, the range must be electrically grounded in accordance
with Canadian Electrical Code. Be sure the range is properly
installed and grounded by a qualified technician.
■
This range is equipped with a three-prong grounding
plug for your protection against shock hazard and
should be plugged directly into a properly grounded
receptacle. Do not cut or remove the grounding
prong from this plug.
■
Disconnect power before servicing.
■
Injuries may result from the misuse of appliance
doors or drawers such as stepping, leaning, or
sitting on the doors or drawers.
■
Maintenance – Keep range area clear and free from
combustible materials, gasoline, and other
flammable vapors and liquids.
■
Storage in or on the Range – Flammable materials
should not be stored in an oven or near surface
units.
■
Top burner flame size should be adjusted so it does
not extend beyond the edge of the cooking utensil.
For self-cleaning ranges –
■
Before Self-Cleaning the Oven – Remove broiler pan
and other utensils. Wipe off all excessive spillage
before initiating the cleaning cycle.
4
FEATURE GUIDE
This manual covers several models. Your model may have some or all of the items listed. Refer to this manual or the Customer Care section
of our website at www.whirlpool.ca for more detailed instructions.
WARNING
Food Poisoning Hazard
Do not let food sit in oven more than one hour before
or after cooking.
Doing so can result in food poisoning or sickness.
KEYPAD FEATURE INSTRUCTIONS
OVEN LIGHT Oven cavity light While the oven door is closed, press OVEN LIGHT to turn the light on and off. The oven light will
come on when the oven door is opened. The oven light will not come on during the Self-Clean
cycle.
SELF-CLEAN Self-clean cycle See the “Range Care” section.
TO LOCK
HOLD 3 SEC
Oven control
lockout
1. Check that the oven is off.
2. Press and hold the TO LOCK HOLD 3 SEC keypad for 3 seconds.
3. A tone will sound, and “Loc” will be displayed.
4. Repeat to unlock. Only the CLOCK and TIMER keypads will function with the controls locked.
CLOCK Clock The Clock uses a 12-hour cycle with a.m. and p.m.
1. Check that the oven is off.
2. Press CLOCK.
3. Press TEMP/TIME “+” or “-” arrow pads to set the time of day, including a.m. or p.m.
4. Press SET CLOCK or START.
TIMER
SET/OFF
Oven timer The Timer can be set in hours or minutes up to 12 hours and 59 minutes.
1. Press TIMER.
2. Press TEMP/TIME “+” or “-” arrow pads to set the length of time.
3. Press START to begin the countdown. If enabled, end-of-cycle tones will sound at end of
countdown.
4. Press TIMER twice to cancel the Timer. Do not press the CANCEL/OFF keypad because the
oven will turn off.
5. If the TIMER is running, but not in the display, press TIMER to display the countdown for
5 seconds.
BAKE Baking and
roasting
1. Press BAKE.
2. Press TEMP/TIME “+” or “-” arrow pads to set a temperature other than 350°F (175°C) in
5° increments between 170°F and 525°F (75°C and 275°C).
3. Press START.
4. To change the temperature repeat Step 2. Press START or wait 5 seconds for the change to
take effect.
5. Press CANCEL/OFF when finished.
BROIL Broiling 1. Position cookware in oven and close the oven door.
2. Press BROIL.
3. Press TEMP/TIME “+” or “-” arrow pads to change the temperature in 5°F (5°C) increments
between 300°F and 525°F (150°C and 275°C).
4. Press START.
5. Press CANCEL/OFF when finished.
WARM Hold warm Food must be at serving temperature before placing it in the warmed oven.
1. Press WARM.
2. Temperature is set at 170°F (75°C) for 60 minutes (1.00 hour).
3. Press START.
4. Press CANCEL/OFF when finished.
5
COOKTOP USE
Electric igniters automatically light the surface burners when
control knobs are turned to IGNITE.
Before setting a control knob, place filled cookware on the grate.
Do not operate a burner using empty cookware or without
cookware on the grate.
To Set:
1. Push in and turn knob counterclockwise to IGNITE.
All 4 surface burners will click. Only the burner with the control
knob turned to IGNITE will produce a flame.
2. Turn knob to anywhere between HIGH and LOW.
Power Failure
In case of prolonged power failure, the surface burners can be lit
manually. Hold a lit match near a burner and turn knob
counterclockwise to IGNITE. After burner lights, turn knob to
setting.
Sealed Surface Burners
IMPORTANT: Do not obstruct the flow of combustion and
ventilation air around the burner grate edges.
Burner cap: Always keep the burner cap in place when using a
surface burner. A clean burner cap will help avoid poor ignition and
uneven flames. Always clean the burner cap after a spillover and
routinely remove and clean the caps according to the “General
Cleaning” section.
Gas tube opening: Gas must flow freely throughout the gas tube
opening for the burner to light properly. Keep this area free of soil
and do not allow spills, food, cleaning agents or any other material
to enter the gas tube opening. Keep spillovers out of the gas tube
by always using a burner cap.
Burner ports: Check burner flames occasionally for proper size
and shape as shown above. A good flame is blue in color, not
yellow. Keep this area free of soil and do not allow spills, food,
cleaning agents or any other material to enter the burner ports.
COOK TIME Timed cooking Timed Cooking allows the oven to be set to turn on at a certain time of day, cook for a set length of
time, and/or shut off automatically. Delay start should not be used for foods such as breads and
cakes because they may not bake properly.
To set a Timed Cook or a Delayed Timed Cook see “Timed Cooking” section.
START TIME Delayed start The Start Time keypad is used to enter the starting time for an oven function with a delayed start.
START Cooking start The Start pad begins any oven function. If Start is not pressed within 5 seconds, “PUSH?” or
“PSH” appears in the display. If Start is not pressed within 1 minute after pressing a keypad, the
function is canceled and the time of day is displayed.
CANCEL/OFF Range function The Cancel/Off keypad stops any function except the Clock, Timer and Oven Control Lockout.
TEMP/TIME Temperature and
time adjust
The “+” or “-” arrow pads are used to adjust time and temperature settings.
KEYPAD FEATURE INSTRUCTIONS
WARNING
Fire Hazard
Do not let the burner flame extend beyond the edge of
the pan.
Turn off all controls when not cooking.
Failure to follow these instructions can result in death
or fire.
REMEMBER: When range is in use or (on some models)
during the Self-Cleaning cycle, the entire cooktop area may
become hot.
A. Burner cap
B. Burner base
C. Alignment pins
D. Igniter
E. Gas tube opening
A. 1-1¹⁄₂" (25-38 mm)
B. Burner ports
A
B
D
E
C
B
A
6
To Clean:
IMPORTANT: Before cleaning, make sure all controls are off and
the oven and cooktop are cool. Do not use oven cleaners, bleach
or rust removers.
1. Remove the burner cap from the burner base and clean
according to “General Cleaning” section.
2. Clean the gas tube opening with a damp cloth.
3. Clean clogged burner ports with a straight pin as shown. Do
not enlarge or distort the port. Do not use a wooden toothpick.
If the burner needs to be adjusted, contact a trained repair
specialist.
4. Replace the burner cap, making sure the alignment pins are
properly aligned with the burner cap.
5. Turn on the burner. If the burner does not light, check cap
alignment. If the burner still does not light, do not service the
sealed burner yourself. Contact a trained repair specialist.
OVEN USE
Odors and smoke are normal when the oven is used the first few
times, or when it is heavily soiled.
IMPORTANT: The health of some birds is extremely sensitive to the
fumes given off. Exposure to the fumes may result in death to
certain birds. Always move birds to another closed and well-
ventilated room.
Electronic Oven Controls
Control Display
The display will flash when powered up or after a power loss. Press
CANCEL/OFF to clear. When oven is not in use, the time of day is
displayed. Indicator lights show functions that are in use.
To ne s
Tones are audible signals, indicating the following:
Basic Functions
One tone
■ Valid pad press
■ Oven is preheated (long tone)
■ Function has been entered
■ Reminder (on some models), repeating each minute after the
end-of-cycle tones
Three tones
■ Invalid pad press
Four tones
■ End of cycle
Fahrenheit and Celsius
The temperature is preset at Fahrenheit, but can be changed to
Celsius.
To change: Press and hold BROIL for 5 seconds. A tone will
sound, and “°C” or “°F” will appear on the display. Repeat to
change back.
To exit mode, press CANCEL/OFF.
Oven Temperature Control
IMPORTANT: Do not use a thermometer to measure oven
temperature because opening the oven door may cause element
cycling to give incorrect readings.
The oven provides accurate temperatures; however, it may cook
faster or slower than your previous oven, so the temperature
calibration can be adjusted. It can be changed in Fahrenheit or
Celsius.
To Adjust Oven Temperature Calibration:
1. Press and hold BAKE for 5 seconds until the oven display
shows the current calibration, for example “0°F CAL” or “00.”
2. Press the TEMP/TIME “+” or “-” arrow pads to increase or to
decrease the temperature in 10°F (5°C) amounts. The
adjustment can be set between 30°F (15°C) and -30°F (-15°C).
3. Press START.
Options Mode
Press and hold TIMER for 5 seconds, and “Opt” will appear. Use
the TEMP/TIME keys to cycle through the following options. Press
CANCEL to exit the mode.
End of Cycle Tones
“b1” (beep once) or “b” (continue to beep) will be displayed. Press
TIMER to toggle through selection.
12-Hour Shutoff
If “12 Hr” is displayed, the oven will automatically shut off after
12 hours. Press TIMER to toggle to “- Hr” to disable the 12-hour
shutoff.
Oven Light with Door Open
“LOn” indicates that the oven light will turn on when the door is
open. If “LOFF” is displayed, the oven light will turn on only with the
oven light switch. Press TIMER to toggle through selection.
Aluminum Foil
IMPORTANT: To avoid permanent damage to the oven bottom
finish, do not line the oven bottom with any type of foil, liners or
cookware.
For best cooking results, do not cover entire oven rack with foil
because air must be able to move freely.
A. Incorrect
B. Correct
A
B
7
Positioning Racks and Bakeware
IMPORTANT: To avoid permanent damage to the porcelain finish,
do not place food or bakeware directly on the oven door or bottom.
Bakeware
To cook food evenly, hot air must be able to circulate. Allow
2" (5 cm) of space around bakeware and oven walls. Make sure
that no bakeware piece is directly over another.
Racks
■ Position racks before turning on the oven.
■ Do not position racks with bakeware on them.
■ Make sure racks are level.
To move a rack, pull it out to the stop position, raise the front edge,
and then lift out. Use the following illustration and charts as a
guide.
Rack Positions
Rack 5: 2-rack baking.
Rack 4: Use for broiling and toasting.
Rack 3: Most baked goods on a cookie sheet, jelly roll pan, or in
muffin pans; casseroles; frozen convenience foods.
Rack 2: Roasting small cuts of meat, pies, casseroles, bundt and
angel food cakes, yeast bread, quick breads, and 2-rack
baking.
Rack 1: Roasting large cuts of meat and poultry.
Rack 6: Extra-large items.
Multiple Rack Cooking
2-rack: Use rack positions 2 and 5.
Baking Layer Cakes on 2 Racks
For best results when baking cakes on 2 racks use racks 2 and 5
for baking. Place the cakes on the racks as shown.
Oven Vent
The oven vent releases hot air and moisture from the oven, and
should not be blocked or covered. Blocking or covering the vent
will cause poor air circulation, affecting cooking and cleaning
results. Do not set plastics, paper or other items that could melt or
burn near the oven vent.
Baking and Roasting
ACCUBAKE
®
Temperature Management System
(on some models)
The ACCUBAKE
®
system electronically regulates the oven heat
levels during preheat and bake to maintain a precise temperature
range for optimal cooking results. The bake and broil elements or
burners cycle on and off in intervals. This feature is automatically
activated when the oven is in use.
Before baking and roasting, position racks according to
“Positioning Racks and Bakeware” section. When roasting, it is not
necessary to wait for the oven preheat cycle to end before putting
food in unless it is recommended in the recipe.
Preheating
When START is pressed, the oven will begin preheating. Once
170ºF (75ºC) is reached, the display temperature will increase as
the actual temperature of the oven increases. When the preheat
temperature is reached, a tone will sound, and the selected
temperature will appear on the display.
Broiling
Broiling uses direct radiant heat to cook food. Changing the
temperature when Custom Broiling allows more precise control
when cooking. The lower the temperature, the slower the cooking.
Thicker cuts and unevenly shaped pieces of meat, fish and poultry
may cook better at lower broiling temperatures.
■ For best results, use a broiler pan and grid. It is designed to
drain juices and help avoid spatter and smoke.
If you would like to purchase a broiler pan, one may be ordered.
Please refer to the cover for contact information. Ask for Part
Number 4396923.
It is not necessary to preheat the oven before putting food in unless
recommended in the recipe. Position food on grid in a broiler pan,
then place it in the center of the oven rack. Close the door to
ensure proper broiling temperature.
6
1
2
3
4
5
A. Oven vent (ceramic glass model)
A
8
Timed Cooking
(on some models)
To Set a Timed Cook:
1. Press BAKE. The bake indicator light will light up.
2. Press the TEMP/TIME “+” or “-” arrow pads to enter a
temperature other than the one displayed.
3. Press COOK TIME. The cook time oven indicator light will light
up.
4. Press the TEMP/TIME “+” or “-” arrow pads to enter the length
of time to cook.
5. Press START. The display will count down the time. When the
time ends, the oven will shut off automatically and “End” will
appear on the display.
6. Press OFF/CANCEL to clear the display.
To Set a Delayed Timed Cook:
Before setting, make sure the clock is set to the correct time of day.
See the “Clock” keypad feature in the “Feature Guide” section.
1. Press BAKE.
2. Press the TEMP/TIME “+” or “-” arrow pads to enter a
temperature other than the one displayed.
3. Press COOK TIME. The cook time oven indicator light will light
up.
4. Press TEMP/TIME “+” or “-” arrow pads to enter the length of
time to cook.
5. Press START TIME. The start time/delay oven indicator light will
light up.
6. Press TEMP/TIME “+” or “-” arrow pads to enter the time of
day to start.
7. Press START.
When the start time is reached, the oven will automatically turn on.
The temperature and/or time settings can be changed anytime
after pressing Start by repeating steps 1-7. When the set cook time
ends, the oven will shut off automatically and “End” will appear on
the display.
8. Press OFF/CANCEL to clear the display.
RANGE CARE
Self-Cleaning Cycle
(on some models)
IMPORTANT: The health of some birds is extremely sensitive to the
fumes given off during the Self-Cleaning cycle. Exposure to the
fumes may result in death to certain birds. Always move birds to
another closed and well-ventilated room.
Do not block the oven vent(s) during the Self-Cleaning cycle. Air
must be able to move freely. Depending on your model, see “Oven
Vent” section.
Do not clean, rub, damage or move the oven door gasket.
Prepare Range
■ Remove the broiler pan, grid, cookware and bakeware, all
cooking utensils, oven racks and aluminum foil and, on some
models, the temperature probe from the oven.
■ Use a damp cloth to clean inside door edge and the
1½" (3.8 cm) area around the inside oven cavity frame, being
certain not to move or bend the gasket.
■ Remove plastic items from the cooktop because they may
melt.
■ Remove all items from the storage drawer.
How the Cycle Works
IMPORTANT: The heating and cooling of porcelain on steel in the
oven may result in discoloring, loss of gloss, hairline cracks and
popping sounds.
Before self-cleaning, make sure the door is completely closed or
the door will not lock and the self-cleaning cycle will not begin.
Once the oven has completely cooled, remove ash with a damp
cloth. To avoid breaking the glass, do not apply a cool damp cloth
to the inner door glass before it has completely cooled.
To stop the self-cleaning cycle at anytime, press CANCEL/OFF. If
the temperature is too high the oven door will remain locked and
“cool” and “locked” will be displayed.
Once the cleaning temperature has been reached, the electronic
control requires a 12-hour delay before another self-clean cycle
can be started.
The oven light will not function during the self-cleaning cycle.
Electronic Oven Control with Adjustable Clean Time (on
some models)
The SELF CLEAN self-cleaning cycle is time adjustable between
2 hours 30 minutes and 4 hours 30 minutes in 15-minute
increments. Suggested clean times are 2 hours 30 minutes for light
soil, and 4 hours 30 minutes for heavy soil. The last 30 minutes of
the cycle is for cool down.
To Self-Clean:
1. Press SELF CLEAN.
2. Press the TEMP/TIME “+” or “-” arrow pads to enter the
desired self-clean cycle time.
3. Press START.
The oven door will automatically lock. The DOOR LOCKED and
CLEAN indicator lights will be displayed. The time remaining
will also be displayed.
4. When the self-clean cycle is complete and the oven cools, the
DOOR LOCKED and CLEAN indicator lights will turn off.
5. When the oven is completely cooled, remove ash with a damp
cloth.
WARNING
Food Poisoning Hazard
Do not let food sit in oven more than one hour before
or after cooking.
Doing so can result in food poisoning or sickness.
WARNING
Burn Hazard
Do not touch the oven during the Self-Cleaning cycle.
Keep children away from oven during
Self-Cleaning cycle.
Failure to follow these instructions can result in burns.
9
General Cleaning
IMPORTANT: Before cleaning, make sure all controls are off and
the oven and cooktop are cool. Always follow label instructions on
cleaning products. For additional information, you can visit the
Customer Service section of our website at www.whirlpool.ca.
Soap, water and a soft cloth or sponge are suggested first unless
otherwise noted.
EXTERIOR PORCELAIN ENAMEL SURFACES (on some
models)
Food spills containing acids, such as vinegar and tomato, should
be cleaned as soon as the entire range is cool. These spills may
affect the finish.
Cleaning Method:
■ Glass cleaner, mild liquid cleaner or nonabrasive scrubbing
pad:
Gently clean around the model and serial number plate
because scrubbing may remove numbers.
■ All-Purpose Appliance Cleaner Part Number 31682B (not
included):
See cover for contact information.
STAINLESS STEEL (on some models)
NOTE: To avoid damage to stainless steel surfaces, do not use
soap-filled scouring pads, abrasive cleaners, Cooktop Cleaner,
steel-wool pads, gritty washcloths or abrasive paper towels.
Damage may occur to stainless steel surfaces, even with one-time
or limited use.
Cleaning Method:
Rub in direction of grain to avoid damaging.
■ Stainless Steel Cleaner and Polish Part Number 31462B:
See cover for contact information.
Liquid detergent or all-purpose cleaner:
Rinse with clean water and dry with soft, lint-free cloth.
METALLIC PAINT (on some models)
Do not use abrasive cleaners, cleaners with bleach, rust removers,
ammonia or sodium hydroxide (lye) because paint surface may
stain.
PORCELAIN-COATED GRATES AND CAPS
Food spills containing acids, such as vinegar and tomato, should
be cleaned as soon as the cooktop, grates and caps are cool.
These spills may affect the finish.
To avoid chipping, do not bang grates and caps against each other
or hard surfaces such as cast iron cookware.
Do not reassemble caps on burners while wet.
Do not clean in the Self-Cleaning cycle.
Cleaning Method:
■ Nonabrasive plastic scrubbing pad and mildly abrasive
cleanser:
Clean as soon as cooktop, grates and caps are cool.
■ Dishwasher (grates only, not caps):
Use the most aggressive cycle. Cooked-on soils should be
soaked or scrubbed before going into a dishwasher.
■ Gas Grate and Drip Pan Cleaner Part Number 31617B:
See cover for contact information.
SURFACE BURNERS
■ See “Sealed Surface Burners” section.
COOKTOP CONTROLS
To avoid damage to the cooktop controls, do not use steel wool,
abrasive cleansers or oven cleaner.
Do not soak knobs. When replacing knobs, make sure knobs are in
the OFF position.
On some models, do not remove seals under knobs.
Cleaning Method:
■ Soap and water:
Pull knobs straight away from control panel to remove.
CONTROL PANEL AND OVEN DOOR EXTERIOR
To avoid damage to the control panel, do not use abrasive
cleaners, steel-wool pads, gritty washcloths or abrasive paper
towels.
Cleaning Method:
■ Glass cleaner and soft cloth or sponge:
Apply glass cleaner to soft cloth or sponge, not directly on
panel.
■ All-Purpose Appliance Cleaner Part Number 31682B (not
included):
See cover for contact information.
OVEN RACKS
Cleaning Method:
■ Steel-wool pad
■ For racks that have discolored and are harder to slide, a light
coating of vegetable oil applied to the rack guides will help
them slide.
STORAGE DRAWER
Check that storage drawer is cool and empty before cleaning.
Cleaning Method:
■ Mild detergent
Oven Light
The oven light is a standard 40-watt appliance bulb. Before
replacing, make sure the oven and cooktop are cool and the
control knobs are in the off position.
To Replace:
1. Unplug range or disconnect power.
2. Turn the glass bulb cover in the back of the oven
counterclockwise to remove.
3. Turn bulb counterclockwise to remove from socket.
4. Replace bulb, then bulb cover by turning clockwise.
5. Plug in range or reconnect power.
10
TROUBLESHOOTING
First try the solutions suggested here or visit our website and reference the Customer Care section
to possibly avoid the cost of a service call.
www.whirlpool.ca
Nothing will operate
■ Is the power supply cord unplugged?
Plug into a grounded 3 prong outlet.
■ Household fuse blown or circuit breaker tripped?
Replace the fuse or reset the circuit breaker. If the problem
continues, call an electrician.
■ Is the main or regulator gas shutoff valve in the off
position?
See Installation Instructions.
■ Is the range properly connected to the gas supply?
Contact a trained repair specialist or see Installation
Instructions.
Surface burners will not operate
■ Is the oven in self-clean?
Surface burners will not operate during self-clean cycle.
■ Is the control knob set correctly?
Push in knob before turning to a setting.
■ Is this the first time the surface burners have been used?
Turn on any one of the surface burner knobs to release air from
the gas lines.
■ Are the burner ports clogged?
See “Sealed Surface Burners” section.
Surface burner flames are uneven, yellow and/or noisy
■ Are the burner ports clogged?
See “Sealed Surface Burners” section.
■ On models with caps, are the burner caps positioned
properly?
See “Sealed Surface Burners” section.
■ Is propane gas being used?
The range may have been converted improperly. Contact a
service technician or see cover for contact information.
Surface burner makes popping noises
■ Is the burner wet?
Let it dry.
Gas range noises during Bake and Broil operations
Noises that may be heard during the Bake and Broil operations:
Whooshing, Poof, Clicking, Snaps, Pop
These sounds are normal operational noises that can be heard
each time the Bake or Broil burners ignite during the cycle.
■ A pop can be heard when the gas valve is opening or cycling
on and will make a single pop when it snaps open from the
solenoid. It sounds similar to a suction cup being pulled off of a
piece of glass.
■ The igniters will click several times until the flame is detected.
These are short clicking sounds like tapping a nail onto a piece
of glass.
■ A whooshing or poof sound is heard when the Bake or Broil
burner ignites.
■ On some models, a clicking sound can be heard when the
convection fan relay cycles on and off.
Excessive heat around cookware on cooktop
■ Is the cookware the proper size?
Use cookware about the same size as the surface cooking
area, element or surface burner. Cookware should not extend
more than ½" (1.3 cm) outside the cooking area.
Cooktop cooking results not what expected
■ Is the proper cookware being used?
Ideal cookware should have a flat bottom, straight sides and a
well fitting lid, and the material should be of a medium to heavy
thickness.
■ Is the control knob set to the proper heat level?
See “Cooktop Use” section.
■ Is the range level?
Level the range. See the Installation Instructions.
Oven will not operate
■ Is this the first time the oven has been used?
Turn on any one of the surface burner knobs to release air from
the gas lines.
■ Is the electronic oven control set correctly?
See “Electronic Oven Controls” section.
Oven burner flames are yellow or noisy
■ Is propane gas being used?
The range may have been converted improperly. Contact a
service technician or see cover for contact information.
Oven temperature too high or too low
■ Does the oven temperature calibration need adjustment?
See “Oven Temperature Control” section of the “Electronic
Oven Controls” section.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
11
Display shows messages
■ Is the display showing a flashing time?
There has been a power failure. Clear the display. On some
models, reset the clock, if needed. See “Clock” keypad feature
in the “Feature Guide” section.
■ Is the display showing a letter followed by a number?
Depending on your model, press OFF/CANCEL or CANCEL/
OFF to clear the display. See “Control Display” in the
“Electronic Oven Controls” section. If it reappears, call for
service. See cover for contact information.
■ Is the display showing a flashing “PUSH?” or “PSH”?
See the “Start” keypad feature in the “Feature Guide” section.
Self-Cleaning cycle will not operate
■ Is the oven door open?
Close the oven door all the way.
■ Has the function been entered?
See “Self-Cleaning Cycle” section.
■ Has a delay start been set? (on some models)
See “Timed Cooking” section.
■ Has a self-clean cycle been run in the past 12 hours?
If a self-clean cycle has been run, or canceled after the oven
has reached temperature, you will have to wait 12 hours to
restart.
Oven cooking results not what expected
■ Is the range level?
Level the range. See the Installation Instructions.
■ Is the proper temperature set?
Double-check the recipe in a reliable cookbook.
■ Is the proper oven temperature calibration set?
See “Oven Temperature Control” section of the “Electronic
Oven Controls” section.
■ Was the oven preheated?
See “Baking and Roasting” section.
■ Are the racks positioned properly?
See “Positioning Racks and Bakeware” section.
■ Is there proper air circulation around bakeware?
See “Positioning Racks and Bakeware” section.
■ Is the batter evenly distributed in the pan?
Check that batter is level in the pan.
■ Is the proper length of time being used?
Adjust cooking time.
■ Has the oven door been opened while cooking?
Oven peeking releases oven heat and can result in longer
cooking times.
■ Are baked items too brown on the bottom?
Move rack to higher position in the oven.
■ Are pie crust edges browning early?
Use aluminum foil to cover the edge of the crust and/or reduce
baking temperature.
ACCESSORIES
Stainless Steel Cleaner and Polish
(stainless steel models)
Order Part Number 31462B
All-Purpose Appliance Cleaner
Order Part Number 31682B
Gas Grate and Drip Pan Cleaner
Order Part Number 31617B
Split-Rack with Removable Insert
Order Part Number 4396927
Broiler Pan
Order Part Number 4396923
12
WHIRLPOOL CORPORATION MAJOR APPLIANCE WARRANTY
LIMITED WARRANTY
For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or
furnished with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter “Whirlpool”) will pay for Factory Specified Parts and
repair labor to correct defects in materials or workmanship. Service must be provided by a Whirlpool designated service company. This
limited warranty is valid only in the United States or Canada and applies only when the major appliance is used in the country in which it
was purchased. Outside the 50 United States and Canada, this limited warranty does not apply. Proof of original purchase date is required
to obtain service under this limited warranty.
ITEMS EXCLUDED FROM WARRANTY
This limited warranty does not cover:
1. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or repair
house fuses, or to correct house wiring or plumbing.
2. Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty
coverage.
3. Repairs when your major appliance is used for other than normal, single-family household use or when it is used in a manner that is
contrary to published user or operator instructions and/or installation instructions.
4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in accordance
with electrical or plumbing codes, or use of consumables or cleaning products not approved by Whirlpool.
5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage
results from defects in materials or workmanship and is reported to Whirlpool within 30 days from the date of purchase.
6. Any food loss due to refrigerator or freezer product failures.
7. Costs associated with the removal from your home of your major appliance for repairs. This major appliance is designed to be
repaired in the home and only in-home service is covered by this warranty.
8. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
9. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an
authorized Whirlpool servicer is not available.
10. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance with
published installation instructions.
11. Major appliances with original model/serial numbers that have been removed, altered or cannot be easily determined. This warranty is
void if the factory applied serial number has been altered or removed from your major appliance.
The cost of repair or replacement under these excluded circumstances shall be borne by the customer.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED
HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,
ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL
OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL
OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF MERCHANTABILITY OR
FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE OR PROVINCE TO PROVINCE.
If outside the 50 United States and Canada, contact your authorized Whirlpool dealer to determine if another warranty applies. 9/07
For additional product information, visit www.whirlpool.ca
If you do not have access to the Internet and you need assistance using your product or you would like to schedule service, you may
contact Whirlpool at the number below.
Have your complete model number ready. You can find your model number and serial number on the label, located on the oven frame
behind the storage drawer panel.
For assistance or service call 1-800-807-6777.
If you need further assistance, you can write to Whirlpool with any questions or concerns at the address below:
Whirlpool Brand Home Appliances
Customer eXperience Centre
1901 Minnesota Court
Mississauga, Ontario L5N 3A7
Please include a daytime phone number in your correspondence.
Please keep this User Instructions and model number information for future reference.
13
Notes
14
MERCI d'avoir acheté ce produit de grande qualité. Si vous rencontrez un problème non abordé à la section DÉPANNAGE, veuillez
visiter notre site Web à www.whirlpool.ca pour obtenir des informations supplémentaires. Si vous avez toujours besoin d'aide,
composez le 1-800-807-6777.
Vous devrez connaître les numéros de modèle et de série qui se trouvent sur le châssis du four, derrière le panneau du tiroir de
remisage.
®
INSTRUCTIONS D'UTILISATION
DE LA CUISINIÈRE À GAZ
Table des matières
SÉCURITÉ DE LA CUISINIÈRE............................................................ 15
La bride antibasculement................................................................... 16
GUIDE DES CARACTÉRISTIQUES ..................................................... 17
UTILISATION DE LA TABLE DE CUISSON ........................................ 18
Brûleurs de surface scellés ................................................................ 19
UTILISATION DU FOUR ....................................................................... 20
Commandes électroniques du four ................................................... 20
Papier d’aluminium............................................................................. 20
Positionnement des grilles et des ustensiles de cuisson.................. 20
Évent du four ...................................................................................... 21
Cuisson au four et rôtissage .............................................................. 21
Cuisson au gril.................................................................................... 21
Cuisson minutée (sur certains modèles)............................................ 22
ENTRETIEN DE LA CUISINIÈRE ......................................................... 22
Programme d’autonettoyage (sur certains modèles) ........................ 22
Nettoyage général .............................................................................. 23
Lampe du four .................................................................................... 24
DÉPANNAGE......................................................................................... 24
ACCESSOIRES...................................................................................... 26
GARANTIE ............................................................................................. 26
15
SÉCURITÉ DE LA CUISINIÈRE
Risque possible de décès ou de blessure grave si vous ne
suivez pas immédiatement les instructions.
Risque possible de décès ou de blessure grave si vous
ne suivez pas les instructions.
Tous les messages de sécurité vous diront quel est le danger potentiel et vous disent comment réduire le risque de blessure et
ce qui peut se produire en cas de non-respect des instructions.
Votre sécurité et celle des autres est très importante.
Nous donnons de nombreux messages de sécurité importants dans ce manuel et sur votre appareil ménager. Assurez-vous de
toujours lire tous les messages de sécurité et de vous y conformer.
AVERTISSEMENT
DANGER
Voici le symbole d’alerte de sécurité.
Ce symbole d’alerte de sécurité vous signale les dangers potentiels de décès et de blessures graves à vous
et à d’autres.
Tous les messages de sécurité suivront le symbole d’alerte de sécurité et le mot “DANGER” ou
“AVERTISSEMENT”. Ces mots signifient :
AVERTISSEMENT : Si les renseignements dans ce manuel ne sont pas exactement
observés, un incendie ou une explosion peut survenir, causant des dommages au
produit, des blessures ou un décès.
– Ne pas entreposer ni utiliser de l’essence ou d’autres vapeurs ou liquides inflammables
à proximité de cet appareil ou de tout autre appareil électroménager.
– QUE FAIRE DANS LE CAS D’UNE ODEUR DE GAZ :
•
Ne pas tenter d’allumer un appareil.
•
Ne pas toucher à un commutateur électrique.
•
Ne pas utiliser le téléphone se trouvant sur les lieux.
•
Appeler immédiatement le fournisseur de gaz à partir du téléphone d'un voisin. Suivre
ses instructions.
•
À défaut de joindre votre fournisseur de gaz, appeler les pompiers.
– L’installation et l’entretien doivent être effectués par un installateur qualifié, une agence
de service ou le fournisseur de gaz.
16
La bride antibasculement
Dans des conditions de service normales, la cuisinière ne bascule pas. Elle peut cependant basculer si une force ou un poids excessif est
appliqué sur la porte ouverte alors que la bride antibasculement n’est pas convenablement fixée.
Risque de basculement
Un enfant ou une personne adulte peut faire basculer la cuisinière ce qui peut causer un décès.
Joindre la bride antibasculement au pied arrière de la cuisinière.
Joindre de nouveau la bride antibasculement si la cuisinière est déplacée.
Voir détails dans les instructions d'installation.
Le non-respect de ces instructions peut causer un décès ou des brûlures graves aux enfants et
aux adultes.
La bride antibasculement
Assurez-vous qu'une bride antibasculement est installée :
• Glisser la cuisinière vers l'avant.
• Vérifier que la bride antibasculement est bien fixée au plancher.
• Glisser de nouveau la cuisinière vers l'arrière de sorte que le pied est sous la bride
antibasculement.
Le pied de la cuisinière
AVERTISSEMENT
IMPORTANTES INSTRUCTIONS DE SÉCURITÉ
CONSERVEZ CES INSTRUCTIONS
AVERTISSEMENT : Pour réduire le risque d’incendie, de
choc électrique, de blessures ou de dommages lors de
l’utilisation de la cuisinière, il convient d’observer certaines
précautions élémentaires dont les suivantes :
■ AVERTISSEMENT : POUR MINIMISER LE RISQUE DE
BASCULEMENT DE LA CUISINIÈRE, ELLE DOIT ÊTRE
BIEN IMMOBILISÉE PAR DES DISPOSITIFS
ANTIBASCULEMENT CORRECTEMENT INSTALLÉS.
POUR VÉRIFIER SI LES DISPOSITIFS SONT
CORRECTEMENT INSTALLÉS, GLISSER LA CUISINIÈRE
VERS L’AVANT ET VÉRIFIER SI LA BRIDE
ANTIBASCULEMENT EST BIEN FIXÉE AU PLANCHER, ET
GLISSER LA CUISINIÈRE VERS L’ARRIÈRE POUR QUE LE
PIED ARRIÈRE DE LA CUISINIÈRE SOIT SOUS LA BRIDE
ANTIBASCULEMENT.
■ AVERTISSEMENT : NE JAMAIS utiliser cet appareil
comme dispositif de chauffage de la pièce. Le non-respect
de cette instruction peut entraîner une intoxication au
monoxyde de carbone et une surchauffe du four.
■ AVERTISSEMENT : NE JAMAIS couvrir les fentes,
trous ou passages d'air au fond du four ou couvrir
entièrement une grille avec des matériaux tels que du
papier d'aluminium. Le non-respect de cette instruction
empêche la circulation de l'air dans le four et peut entraîner
une intoxication au monoxyde de carbone. Les feuilles de
papier d'aluminium peuvent également retenir la chaleur et
créer un risque d'incendie.
■ MISE EN GARDE : Ne pas remiser dans des armoires
au-dessus de la cuisinière ou sur le dosseret d’une
cuisinière, des objets que des enfants pourraient vouloir
atteindre. Les enfants pourraient se brûler ou se blesser en
grimpant sur la cuisinière.
■ Installation appropriée – La cuisinière, lorsqu’elle est
correctement installée, doit être reliée à la terre
conformément aux codes électriques locaux ou en
l’absence de codes locaux, selon le Code électrique national
(US) ANSI/NFPA 70 ou le Code canadien des installations,
Partie 1. S’assurer que la cuisinière est correctement
installée et reliée à la terre par un technicien qualifié.
■ Cette cuisinière est munie d’une fiche de liaison à la terre à
trois broches pour votre protection contre les risques de
choc électrique et doit être branchée directement dans une
prise de courant bien reliée à la terre. Ne pas couper ni
enlever la broche de liaison à la terre de cette fiche.
■ Déconnecter la source de courant électrique avant
l'entretien.
■ Des blessures peuvent survenir d’un mauvais usage des
portes ou des tiroirs de l’appareil tel que se tenir debout sur
la surface, se pencher ou s’asseoir sur les portes ou tiroirs.
■ Entretien – Garder l’espace autour de la cuisinière dégagé
et libre de matériaux combustibles, d’essence et d’autres
vapeurs et liquides inflammables.
■ Remisage dans ou sur la cuisinière – Des produits
inflammables ne devraient pas être remisés dans un four ou
près des éléments de surface.
■ La taille de la flamme des brûleurs de surface devrait être
ajustée de sorte qu’elle ne dépasse pas le bord de
l’ustensile de cuisson.
Cuisinière autonettoyante –
■ Avant l’autonettoyage du four – Ôter la lèchefrite et son plat
et les autres ustensiles. Essuyer tous les renversements
excessifs avant de mettre en marche le programme
d’autonettoyage.
17
GUIDE DES CARACTÉRISTIQUES
Ce manuel couvre différents modèles. Il est possible que votre modèle ne comporte pas toutes les caractéristiques décrites. Consulter ce
manuel ou le section service à la clientèle de notre site Web sur www.whirlpool.ca pour des instructions plus détaillées.
AVERTISSEMENT
Risque d'empoisonnement alimentaire
Ne pas laisser des aliments dans un four plus d'une
heure avant ou après la cuisson.
Le non-respect de cette instruction peut causer un
empoisonnement alimentaire ou une maladie.
CLAVIER CARACTÉRISTIQUE INSTRUCTIONS
OVEN LIGHT
(Lampe du four)
Lampe de la cavité
du four
Alors que la porte du four est fermée, appuyer sur OVEN LIGHT (lampe du four) pour allumer
ou éteindre la lampe. La lampe du four s'allume à l'ouverture de la porte. La lampe du four
ne s’allume pas durant le programme d’autonettoyage.
SELF-CLEAN
(autonettoyage)
Programme
d’autonettoyage
Voir la section “Entretien de la cuisinière”.
TO LOCK
HOLD 3 SEC
(appuyer
pendant 3
secondes pour
verrouiller)
Verrouillage des
commandes du four
1. Vérifier que le four est éteint.
2. Appuyer pendant 3 secondes sur la touche TO LOCK HOLD 3 SEC pour verrouiller.
3. Un signal sonore se fait entendre et “Loc” apparaît sur l'afficheur.
4. Répéter pour déverrouiller. Seules les touches CLOCK, OVEN LIGHT, et TIMER (horloge,
lampe du four et minuterie) fonctionnent lorsque les commandes sont verrouillées.
CLOCK (horloge) Horloge L'horloge utilise un format de 12 heures avec a.m. et p.m.
1. Vérifier que le four est éteint.
2. Appuyer sur CLOCK (horloge).
3. Appuyer sur les touches à flèche TEMP/TIME (température/durée) “+” ou “-”, pour régler
l'heure, y compris a.m. ou p.m.
4. Appuyer sur CLOCK (horloge) ou START (mise en marche).
TIMER SET/OFF
(minuterie)
Minuterie du four La minuterie peut être réglée en heures ou en minutes jusqu'à concurrence de 12 heures et
59 minutes.
1. Appuyer sur TIMER (minuterie).
2. Appuyer sur les touches à flèche TEMP/TIME “+” ou “-”, pour régler la durée de cuisson.
3. Appuyer sur START (mise en marche) pour commencer le compte à rebours. Si activés,
les signaux sonores de fin de programme se font entendre à la fin du compte à rebours.
4. Appuyer deux fois sur TIMER (minuterie) pour annuler la minuterie. Ne pas appuyer sur
la touche CANCEL/OFF (annulation/arrêt) sinon le four s’éteindra.
5. Si TIMER (minuterie) est activé mais n'apparaît pas sur l'affichage, appuyer sur TIMER
(minuterie) pour faire apparaître le compte à rebours pendant 5 secondes.
BAKE (cuisson
au four)
Cuisson au four et
rôtissage
1. Appuyer sur BAKE (cuisson au four).
2. Appuyer sur les touches à flèche TEMP/TIME “+” ou “-”, pour régler une température
autre que 350°F (175°C) par tranches de 5°, entre 170°F et 525°F (75°C et 275°C).
3. Appuyer sur START (mise en marche).
4. Pour modifier la température, répéter les étape 2. Appuyer sur START ou attendre
pendant 5 secondes pour que le changement puisse s'effectuer.
5. Appuyer sur CANCEL/OFF (annulation/arrêt) après avoir terminé.
BROIL (cuisson
au gril)
Cuisson au gril 1. Positionner l'ustensile à l'intérieur du four et fermer la porte du four.
2. Appuyer sur BROIL (cuisson au gril).
3. Appuyer sur les touches à flèche TEMP/TIME “+” ou “-”, pour modifier la température
par tranches de 5°F (5°C), entre 300°F et 525°F (150°C et 275°C).
4. Appuyer sur START (mise en marche).
5. Appuyer sur CANCEL/OFF (annulation/arrêt) après avoir terminé.
18
UTILISATION DE LA TABLE DE CUISSON
Les allumeurs électriques allument automatiquement les brûleurs
de surface quand les boutons de commandes sont placés sur
IGNITE.
Avant de régler un bouton de commande, placer l’ustensile de
cuisson rempli sur la grille. Ne pas faire fonctionner un brûleur avec
un ustensile de cuisson vide ou sans ustensile de cuisson sur la
grille.
Réglage :
1. Appuyer sur le bouton et le tourner dans le sens antihoraire
pour le placer sur IGNITE.
Les 4 brûleurs de surface émettront un déclic. Seul le brûleur
dont le bouton est placé sur IGNITE produira une flamme.
2. Tourner le bouton à n'importe quel réglage entre HIGH (élevée)
et LOW (basse).
Panne de courant
En cas de panne de courant prolongée, les brûleurs de surface
peuvent être allumés manuellement. Tenir une allumette allumée
près d’un brûleur et tourner le bouton dans le sens antihoraire pour
le placer sur IGNITE. Lorsque le brûleur s’allume, tourner le bouton
au réglage souhaité.
WARM (tiède) Garder tiède Les aliments doivent être à la température de service avant d'être placés dans le four chaud.
1. Appuyer sur WARM (tiède).
2. La température est réglée à 170°F (75°C) pendant 60 minutes (1 heure).
3. Appuyer sur START (mise en marche).
4. Appuyer sur CANCEL/OFF (annulation/arrêt) après avoir terminé.
COOK TIME
(cuisson minutée
- sur certains
modèles)
Cuisson minutée La cuisson minutée permet d’allumer le four à une certaine heure de la journée, de faire
cuire pendant une durée réglée et/ou d’éteindre le four automatiquement. La mise en
marche différée ne doit pas être utilisée pour les aliments tels que pains et gâteaux car ils
risquent de ne pas bien cuire.
Pour régler une cuisson minutée ou une cuisson minutée différée, voir la section “Cuisson
minutée”.
START TIME
(heure de mise
en marche)
Mise en marche
différée
La touche de l'heure de mise en marche sert à entrer l'heure de mise en marche pour un
four équipé de mise en marche différée.
START (mise en
marche)
Mise en marche de
la cuisson
La touche Start active toutes les fonctions du four. Si l'on n'appuie pas sur Start (mise en
marche) dans les 5 secondes, “PUSH?” ou “PSH” (appuyer) apparaît sur l'affichage. Si,
après avoir appuyé sur une touche, on n'appuie pas sur Start dans la minute qui suit, la
fonction est annulée et l'heure s'affiche.
CANCEL/OFF
(annulation/arrêt)
Fonction de la
cuisinière
La touche Cancel/Off (annulation/arrêt) désactive toutes les fonctions à l'exception de
l'horloge, de la minuterie et du verrouillage des commandes du four.
TEMP/TIME
(température/
durée)
Réglage de
température et
durée
Les touches à flèche “+” ou “-” servent à régler la durée et la température.
CLAVIER CARACTÉRISTIQUE INSTRUCTIONS
Risque d’incendie
La flamme d'un brûleur ne devrait pas dépasser le bord
du récipient de cuisson.
Fermer tous les réglages lorsque la cuisson est
terminée.
Le non-respect de ces instructions peut causer un
décès ou un incendie.
AVERTISSEMENT
N’OUBLIEZ PAS : Quand l’appareil est utilisé ou (sur
certains modèles) durant le programme d’autonettoyage,
toute la surface de la table de cuisson peut devenir chaude.
19
Brûleurs de surface scellés
IMPORTANT : Ne pas entraver le débit de gaz de combustion et
de l’air de ventilation autour des bords des grilles de brûleur.
Chapeau de brûleur : Toujours garder le chapeau du brûleur en
place lorsqu’un brûleur de surface est utilisé. Un chapeau de
brûleur propre empêche un mauvais allumage et une flamme
inégale. Toujours nettoyer le chapeau de brûleur après un
renversement, enlever et nettoyer régulièrement les chapeaux
conformément à la section “Nettoyage général”.
Ouverture du tube d’arrivée de gaz : Pour que le brûleur s’allume
convenablement, il faut que le gaz puisse passer librement à
travers l’ouverture du tube d’arrivée de gaz. Il est essentiel de
garder cette zone exempte de souillures et de veiller à ce que les
renversements, aliments, agents de nettoyage ou autre matériau ne
puissent pénétrer dans l’ouverture du tube d’arrivée de gaz.
Protéger le tube d'arrivée de gaz contre les renversements en
utilisant toujours un chapeau de brûleur.
Orifices de brûleur : Examiner occasionnellement les flammes des
brûleurs pour en vérifier la taille et la forme tel qu’indiqué ci-
dessus. Une bonne flamme est bleue, pas jaune. Il est essentiel de
garder cette zone exempte de souillures et de veiller à ce que les
renversements, aliments, agents de nettoyage ou autre matériau ne
puissent pénétrer dans les orifices de brûleur.
Nettoyage :
IMPORTANT : Avant de faire le nettoyage, s’assurer que toutes les
commandes sont éteintes et que le four et la table de cuisson sont
froids. Ne pas utiliser de nettoyants à four, eau de Javel ou
décapants à rouille.
1. Enlever le chapeau de brûleur de la base du brûleur et nettoyer
conformément à la section “Nettoyage général”.
2. Nettoyer l’ouverture du tube d’arrivée de gaz avec un linge
humide.
3. Nettoyer les orifices de brûleur obstrués avec une épingle
droite tel qu’indiqué. Ne pas agrandir ni déformer les orifices.
Ne pas utiliser un cure-dent en bois. Si le brûleur a besoin
d’être ajusté, faire venir un technicien d’entretien qualifié.
4. Réinstaller le chapeau de brûleur et s’assurer que les tiges
d’alignement sont bien alignées avec le chapeau de brûleur.
5. Allumer le brûleur. Si le brûleur ne s’allume pas, vérifier
l’alignement du chapeau. Si le brûleur ne s’allume toujours pas,
ne pas faire vous-même la réparation du brûleur scellé.
Contacter un technicien d’entretien qualifié.
A. Chapeau de brûleur
B. Base du brûleur
C. Tiges d’alignement
D. Dispositif d’allumage
E. Ouverture du tube d’arrivée de gaz
A. 1-1¹⁄₂" (25-38 mm)
B. Orifices de brûleur
A
B
D
E
C
B
A
A. Incorrect
B. Correct
A
B
20
UTILISATION DU FOUR
Des odeurs et de la fumée sont normales lorsque le four est utilisé
les premières fois, ou lorsqu'il est très sale.
IMPORTANT : La santé de certains oiseaux est très sensible aux
émanations de fumée. L’exposition aux émanations peut entraîner
la mort de certains oiseaux. Toujours déplacer les oiseaux dans
une autre pièce fermée et bien aérée.
Commandes électroniques du four
Afficheur du four
L’afficheur clignote lorsqu’il est mis sous tension ou après une
coupure de courant. Appuyer sur CANCEL/OFF (annulation/arrêt)
pour l’effacer. Lorsque le four n’est pas en marche, l’heure
s’affiche. Les témoins lumineux indiquent les fonctions qui sont
activées.
Signaux sonores
Les signaux sonores indiquent ce qui suit :
Fonctions de base
Un signal sonore unique
■ Appui sur une touche valide
■ Four préchauffé (signal sonore long)
■ Fonction entrée
■ Rappel (sur certains modèles), signal se répétant à intervalles
d'une minute après les signaux sonores de fin de programme
Trois signaux sonores
■ Appui sur une touche non valide
Quatre signaux sonores
■ Fin de programme
Fahrenheit et Celsius
Le four est préréglé pour un affichage de la température en degrés
Fahrenheit, mais on peut permuter en degrés Celsius.
Modification : Appuyer sur la touche BROIL (cuisson au gril)
pendant 5 secondes. Un signal sonore se fait entendre et “°C” ou
“°F” s’affichera. Répéter pour retourner à l'affichage précédent.
Pour sortir de ce mode, appuyer sur CANCEL/OFF (annulation/
arrêt).
Commande de la température du four
IMPORTANT : Ne pas utiliser de thermomètre pour mesurer la
température du four car l'ouverture de la porte du four peut
provoquer des mesures incorrectes du brûleur à fonctionnement
par intermittence.
Le four fournit des températures précises; toutefois, il peut cuire
plus rapidement ou plus lentement que votre ancien four, c’est
pourquoi le calibrage de la température peut être ajusté. Il peut être
changé en degrés Fahrenheit ou en Celsius.
Ajustement du calibrage de la température du four :
1. Appuyer sur BAKE pendant 5 secondes jusqu’à ce que
l’afficheur du four indique le calibrage actuel, par exemple “0°F
CAL” ou “00”.
2. Appuyer sur les touches à flèche TEMP/TIME “+” ou “-”
(température/durée “plus” ou “moins”) pour augmenter ou
réduire la température par tranches de 10°F (5°C). L’ajustement
peut être réglé entre 30°F (15°C) et -30°F (-15°C).
3. Appuyer sur START (mise en marche).
Mode Options
Appuyer sur TIMER (minuterie) pendant 5 secondes et “Opt”
s'affiche. Utiliser les touches TEMP/TIME (température/durée) pour
faire défiler les options suivantes. Appuyer sur CANCEL
(annulation) pour sortir de ce mode.
Signaux sonores de fin de programme
“b1” (n'émet qu'un seul bip) ou “b” (continue à émettre des bips)
s'affiche. Appuyer sur TIMER (minuterie) pour passer d'une
sélection à l'autre.
Arrêt au bout de 12 heures
Si “12 Hr” (12 heures) s'affiche, le four s'éteint automatiquement au
bout de 12 heures.
Appuyer sur TIMER (minuterie) pour faire passer l'affichage à
“- Hr”, afin de désactiver l'arrêt au bout de 12 heures.
Lumière du four avec porte ouverte
“LOn” indique que la lumière du four s'allume lorsque la porte est
ouverte. Si “LOFF” est affiché, la lumière du four ne peut être
allumée qu'au moyen de l'interrupteur. Appuyer sur TIMER
(minuterie) pour passer d'une sélection à l'autre.
Papier d’aluminium
IMPORTANT : Pour éviter des dommages permanents au fini du
fond du four, ne pas recouvrir le fond avec du papier d'aluminium,
un revêtement quelconque ou un ustensile de cuisson.
Pour assurer une bonne circulation de l’air et des résultats de
cuisson optimaux, ne pas recouvrir la grille entière de papier
d’aluminium.
Positionnement des grilles et des ustensiles de cuisson
IMPORTANT : Pour éviter des dommages permanents au fini en
porcelaine, ne pas placer d'aliments ou d'ustensiles de cuisson
directement sur la porte ou sur le fond du four.
Ustensiles de cuisson
L’air chaud doit pouvoir circuler autour de l’aliment pour le cuire
uniformément. Laisser 2" (5 cm) entre les ustensiles de cuisson et
les parois du four. S’assurer qu’aucun ustensile de cuisson ne se
trouve directement au-dessus d’un autre.
Grilles
■ Placer les grilles avant d’allumer le four.
■ Ne pas installer les grilles lorsque des ustensiles de cuisson se
trouvent dessus.
■ S’assurer que les grilles sont d'aplomb.
Pour déplacer une grille, la tirer jusqu’à la butée d’arrêt, soulever le
rebord avant et la tirer pour la sortir du four. Se servir de
l’illustration et du tableau suivants comme guide.
6
1
2
3
4
5
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
Whirlpool W10196152B Manuel utilisateur
- Catégorie
- Cuisinières
- Taper
- Manuel utilisateur
dans d''autres langues
- English: Whirlpool W10196152B User manual