Creative SB1122 Manuel utilisateur

Marque: Creative

Modèle: SB1122

Catégorie: Équipement musical supplémentaire

Taper: Manuel utilisateur

Ce manuel convient également à

Sound Blaster

Wireless Receiver

User’s Guide

Congratulations!

Your Sound Blaster

Wireless Receiver complements Creative transmitters

like Sound Blaster Wireless Transmitter and Sound Blaster X-Fi™ Notebook.

Together, your receiver and transmitter enable you to enjoy high-quality music,

wherever you are in your home, wirelessly. You can also expand your wireless

system by adding on other Sound Blaster Wireless devices.

NOTE

The term “receiver” used throughout this User’s Guide refers to the

Sound Blaster Wireless Receiver. “Transmitter” refers to any of the

transmitters mentioned above.

Sound Blaster

Wireless Rock -

Outdoor Speaker*

Sound Blaster Wireless

Headphones*

Creative GigaWorks

T20W Series II*

Sound Blaster

Wireless Transmitter

Sound Blaster

Wireless Receiver

*Available separately

Creative GigaWorks

T20W Series II*

About Your Receiver 2

About Your Receiver

LINE

OUT

LINK /

CONNECT

1 Power/Standby and

Play/Pause button

Press to turn on.

Press and hold to enable Standby

mode.

2 Next/Fast forward button

Press and hold to Fast forward.

3 Previous/Rewind button

Press and hold to Rewind.

4 Infrared receiver

5 Power LED

See “Understanding the Power

LED” on page 14.

6 Line Out jack

7 RCA Audio Line Out jacks

8 [Link/Connect] LED

button

See “Understanding the Link LED”

on page 14.

9 5V DC In jack

About Your Remote Control 3

About Your Remote Control

Your remote control has an operating distance of up to three meters

(approximately 9.8 feet). To remove and replace the remote control’s battery,

see “Replacing the remote control battery” on page 15.

RM-820

1 Power/Standby

2iPod

Back/Menu*

3 Menu Navigation buttons

Press OK to execute the selected menu option.

4 (Not applicable)

5Next/Fast forward

Press and hold to Fast forward.

6 Play/Pause

7 Previous/Rewind

Press and hold to Rewind.

8 Repeat

9 Shuffle

10 Volume up/down

11 Mute on/off

* For use with transmitters that support iPod

players.

NOTE

The battery is included. Remove the plastic strip

before using the remote control.

Setting Up Your Receiver 4

Setting Up Your Receiver

Step 1: Position your receiver

You can pair (connect wirelessly) your transmitter and receiver before

positioning your receiver. Once paired, place your receiver up to 30 meters

away from your transmitter.

Step 2: Connect your receiver

NOTE

Signal quality between the transmitter and receiver may be affected

by any object or structure (for example, multiple walls) that is

between the units. Experiment with different positions if necessary.

LINK/

CONNECT

5v DC

LINE

OUT

4 5

1 Powered stereo or 2.1 speakers

2 Stereo to RCA cable

3 Stereo cable

4 Power adapter

5 Power outlet

Enable wireless control for your transmitter 5

Step 3: Enable wireless control for your transmitter

For Sound Blaster Wireless Transmitter

The device’s wireless features are enabled by default. If not, refer to its

documentation to enable it.

For Sound Blaster X-Fi Notebook

Follow these steps to enable the device’s wireless features:

1 Launch Entertainment Mode. To do this, click Start -> Programs ->

Creative -> Sound Blaster X-Fi Notebook -> Creative Console Launcher.

2 Click the Wireless Music Control button.

3 Select the Enable Wireless Music Control check box.

The device’s Link LED lights up green.

2 3

CONNE

POWER

Turn on your receiver and Auto Pair 6

Step 4: Turn on your receiver and Auto Pair

Your transmitter and receiver pair (connect wirelessly) automatically when

turned on. The Link LED, at the back of the receiver, flashes and then lights up

green when pairing is successful.

NOTE

If your transmitter and receiver do not pair, simply reset them. On

one unit at a time, press and hold the Connect button for five

seconds.

LINK /

CONNECT

LINK /

CONNECT

RM-820

Play and stream music from transmitter 7

Step 5: Play and stream music from transmitter

Play music on your transmitter and broadcast music to your receiver.

Setting Up Two or More Receivers

Repeat Steps 1 to 2 in “Setting Up Your Receiver” on page 4. In Step 4, turn on

all your receivers. Your receivers pair automatically with your transmitter, and

you can start playing music on all your receivers.

Manual Pairing 8

Manual Pairing

This section shows you how to pair your transmitter manually with two to four

receivers. If you wish to use zone control, you must pair your units manually.

For more information about broadcasting and zone control, see “Using Your

Wireless Features” on page 11.

Only the first four manually paired receivers will be assigned to a wireless

zone. Each manually paired receiver will be assigned to the next available zone.

Step 1: Press the Connect button on your transmitter

With your transmitter and receivers turned on, press the Connect button on

your transmitter. Alternatively, you can click the Connect button in the

transmitter software installed. The transmitter’s Link LED flashes.

CONNECT

Sound Blaster

X-Fi Notebook

Sound Blaster

Wireless

Transmitter

Press the Connect button on your first receiver 9

Step 2: Press the Connect button on your first receiver

This must be done within three minutes after pressing the Connect button on

the transmitter (Step 1). Once the transmitter and receiver are paired

successfully, the Link LED on both units light up green and remain on. The first

receiver to be paired will be assigned to Zone 1.

IMPORTANT

DO NOT press the Connect button repeatedly on your transmitter

or receiver before a pairing process is complete or else you may

not be able to perform the correct zone assignment for your

receivers.

5V DC

LINK /

CONNECT

5V DC

LINK /

CONNECT

Press the Connect button on your transmitter again 10

Step 3: Press the Connect button on your transmitter again

The transmitter’s Link LED flashes. Refer to the diagram in Step 1.

Step 4: Press the Connect button on your second receiver

Refer to the diagram in Step 2. Once the transmitter and receiver are paired

successfully, the Link LED on both units light up green and remain on. Repeat

the steps to pair your third and fourth receivers (if applicable) manually.

Step 5: Test your receivers

1 Play music from your transmitter.

2 Use the transmitter software to select the zones assigned to the receivers

you want to activate or deactivate. See “Using Your Wireless Features” on

page 11 for instructions do this.

NOTE

For troubleshooting information, see “Troubleshooting” on

page 16.

Using Your Wireless Features 11

Using Your Wireless Features

Use the transmitter software installed on your computer to control your

receivers remotely from your transmitter.

Broadcasting

Broadcasting can be used on any number of paired receivers. This feature

enables you to activate or deactivate all paired receivers simultaneously.

For Sound Blaster Wireless Transmitter

In Sound Blaster Wireless Control Panel, click the Broadcast button.

For Sound Blaster X-Fi Notebook

In Entertainment Mode, click the Enable Wireless Control check box.

Transmitter

Receiver

Sound Blaster

X-Fi Notebook

Sound Blaster

Wireless

Transmitter

Using Your Wireless Features 12

Zone Control

Zone control is limited to the first four manually paired receivers. This feature

enables you to activate or deactivate each paired receiver individually.

Transmitter

Receiver

Sound Blaster

X-Fi Notebook

Sound Blaster

Wireless

Transmitter

Using Your Wireless Features 13

For Sound Blaster Wireless Transmitter

1 In Sound Blaster Wireless Control Panel, click the Zone button, and then

click the zones assigned to the receivers you want to activate or deactivate.

2 Clicking the Zone button will put the activated zones/receivers on

standby.

3 Click the Zone button again to activate the previously selected zones/

receivers.

For Sound Blaster X-Fi Notebook

1 In Entertainment Mode, click the Zone button, and then click the zone

number buttons (1 to 4) assigned to the receivers you want to activate or

deactivate.

2 Click the Enable Wireless Music Control check box to deselect it. Activated

receivers will then be on standby.

3 Click the Enable Wireless Music Control check box again to select it.

Previously selected receivers will be activated.

NOTE

Your transmitter can only save and reactivate one combination of

receivers. It remembers the last combination of activated

receivers just before the Zone button is clicked.

Other Information 14

Other Information

Understanding the Power LED

Understanding the Link LED

Returning to factory default settings

Return to the factory default settings if you want to

• revert to the original volume setting,

• reset your zone numbering sequence, or

• “unpair” a receiver.

LED Behavior Status

White Stable Turned on and ready for use

Continuous slow flashing Not detecting any signal or signal

is weak

Red Stable In Standby mode

Quick flashing (twice) Receiving remote control signals

Continuous slow flashing Muted

LED Behavior Status

Green Stable Paired (Turned on / In Standby

mode)

Flashing Pairing in progress

Quick flashing (twice) -> Not lit ->

Stable

Wireless reset

Not lit – Connection lost

Other Information 15

Press and hold the Previous/Rewind and Next/Fast forward buttons on your

receiver together for five seconds. The Power LED goes off for two seconds

before lighting up again.

Replacing the remote control battery

Refer to the following diagram to remove and replace the battery (when it is

depleted) from the remote control.

NOTE

The receiver pairs with your transmitter automatically if both

return to factory default settings.

Troubleshooting 16

Troubleshooting

Here are some tips if you encounter these problems.

There is no sound from the speakers that are connected to the

receiver.

Check the following:

• The Connect LEDs are lit up. Else see the following troubleshooting tip.

• The receiver is connected to the power outlet and turned on.

• The speaker system’s power is turned on.

• You have connected the speakers to your receiver correctly.

• The receiver volume is not muted.

The wireless connection does not seem to work.

The Connect LEDs do not light up.

The signal from the transmitter may be weak or the receiver has lost its

connection with the transmitter.

Try the following:

• Move your transmitter and receiver closer to each other.

• Reposition your transmitter or receiver so that there are fewer objects (for

example, multiple walls or large metal structures) between them.

• Make sure your transmitter and receiver are not placed on metal surfaces.

• Reset the wireless connection. Press and hold the receiver’s Connect button

for five seconds.

• Disconnect the transmitter and receiver from the power source. Then

reconnect them again and reset the wireless connection.

Troubleshooting 17

My receiver seems to be picking up extra noise, or there are

intermittent pauses.

The position of your Sound Blaster Wireless devices as well as signals from

other wireless routers or Bluetooth equipment may affect the quality of the

transmissions.

Try the following:

• In Sound Blaster Wireless Control Panel, change the RF Channel from Auto

to either Ch 1, 2 or 3.

• Place your transmitter and receivers closer to each other.

• Place your transmitter away from other devices that transmit wireless

signals, and away from large metal surfaces.

• Reposition your devices so that there are fewer objects (for example,

multiple walls or large metal structures) between them.

• Set your wireless LAN router's channel to Auto, 1 or 11. To do this, refer to

your router's user documentation.

• Refrain from doing large file transfers via the wireless internet or Bluetooth

connection while you are streaming music. Alternatively, stop streaming

music during intensive file transfers.

I have two Sound Blaster Wireless transmitters. My receiver is

receiving the incorrect transmission.

Your receiver may be alternating transmissions between the transmitters.

Manually pair your receivers. See “Manual Pairing” on page 8.

Troubleshooting 18

My remote control is not responding.

• Your remote control’s battery may have depleted. To remove and replace the

battery, see “Replacing the remote control battery” on page 15.

Also check the following:

• You have installed the transmitter software.

•In the Remote Control Settings application, ensure that the Enable control

of Windows Application check box is selected. To launch this application,

click Start -> All Programs -> Creative -> Remote Control Settings.

• The media player that you are using must be the highlighted window for the

playback functions to work.

I need to change the wireless zone numbers of my receivers.

Do the following:

i. Return the receivers to factory default settings. See “Returning to

factory default settings” on page 14.

ii. Manually pair the receivers. Follow the steps in “Manual Pairing” on

page 8.

All kinds of sounds from my computer are transmitted to the

receiver.

Your transmitter streams all sounds from your computer to the receiver,

including sounds from other programs, as well as system sounds and alerts.

Disable these sounds, or close programs that generate unwanted sounds.

Troubleshooting 19

(For Sound Blaster X-Fi Notebook only)

When I switch my recording source from Mic In to Line In in

Entertainment Mode, the wireless connection is lost.

When the recording source is changed to Mic In, wireless music control is

automatically disabled so that input from the microphone (for example, a

private internet voice conversation) will not be unintentionally streamed to all

paired receivers. After changing the recording source back to Line In, you must

enable the wireless features again in Entertainment Mode.

La page est en cours de chargement...

Creative SB1122 Manuel utilisateur

Marque: Creative

Modèle: SB1122

Catégorie: Équipement musical supplémentaire

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Creative SB1122 User manual

Creative SB1122 Manuel utilisateur

Ce manuel convient également à

Creative SB1122 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents