ASROCK K8NF4G-VSTA Le manuel du propriétaire

11

1

ASRock K8NF4G-VSTA Motherboard

EnglishEnglish

English

Copyright Notice:Copyright Notice:

Copyright Notice:

No part of this installation guide may be reproduced, transcribed, transmitted, or

translated in any language, in any form or by any means, except duplication of

documentation by the purchaser for backup purpose, without written consent of

ASRock Inc.

Products and corporate names appearing in this guide may or may not be registered

trademarks or copyrights of their respective companies, and are used only for

identification or explanation and to the owners’ benefit, without intent to infringe.

Disclaimer:Disclaimer:

Disclaimer:

Specifications and information contained in this guide are furnished for informational

use only and subject to change without notice, and should not be constructed as a

commitment by ASRock. ASRock assumes no responsibility for any errors or

omissions that may appear in this guide.

With respect to the contents of this guide, ASRock does not provide warranty of any

kind, either expressed or implied, including but not limited to the implied warranties or

conditions of merchantability or fitness for a particular purpose.

In no event shall ASRock, its directors, officers, employees, or agents be liable for

any indirect, special, incidental, or consequential damages (including damages for

loss of profits, loss of business, loss of data, interruption of business and the like),

even if ASRock has been advised of the possibility of such damages arising from any

defect or error in the guide or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

ASRock Website: http://www.asrock.com

Published March 2006

22

2

ASRock K8NF4G-VSTA Motherboard

EnglishEnglish

English

Motherboard LMotherboard L

Motherboard L

ayoutayout

ayout

1 PS2_USB_PW1 Jumper 16 Chassis Speaker Header (SPEAKER 1)

2 ATX 12V Power Connector (ATX12V1) 17 USB 2.0 Header (USB67, Blue)

3 754-Pin CPU Socket 18 Infrared Module Header (IR1)

4 CPU Heatsink Retention Module 19 USB 2.0 Header (USB45, Blue)

5 184-pin DDR DIMM Slots (DDR1- 2) 20 Floppy Connector (FLOPPY1)

6 Secondary IDE Connector (IDE2, Black) 21 Flash Memory

7 Primary IDE Connector (IDE1, Blue) 22 Game Port Header (GAME1)

8 North Bridge Controller 23 PCI Express Slot (PCIE2)

9 PCI Express Slot (PCIE1) 24 HDMR Slot (HDMR1)

10 South Bridge Controller 25 Front Panel Audio Header (HD_AUDIO1)

11 Clear CMOS Jumper (CLRCMOS2) 26 2 x PCI Slots (PCI1- 2)

12 Secondary Serial ATAII Connector (SATAII_2, red) 27 Internal Audio Connector: CD1 (Black)

13 Primary Serial ATAII Connector (SATAII_1, red) 28 ATX Power Connector (ATXPWR1)

14 Chassis Fan Connector (CHA_FAN1) 29 Serial Port Connector (COM1)

15 System Panel Header (PANEL1) 30 CPU Fan Connector (CPU_FAN1)

33

3

ASRock K8NF4G-VSTA Motherboard

EnglishEnglish

English

HD 8CH I/OHD 8CH I/O

HD 8CH I/O

1 Parallel Port 8 Microphone (Pink)

2 RJ-45 Port 9 USB 2.0 Ports (USB01)

3 Side Speaker (Gray) 10 USB 2.0 Ports (USB23)

4 Rear Speaker (Black) 11 VGA Port

5 Central / Bass (Orange) 12 PS/2 Keyboard Port (Purple)

6 Line In (Light Blue) 13 PS/2 Mouse Port (Green)

*7 Front Speaker (Lime)

* If you use 2-channel speaker, please connect the speaker’s plug into “Front Speaker Jack”. See

the table below for connection details in accordance with the type of speaker you use.

TABLE for Audio Output Connection

Audio Output Channels Front Speaker Rear Speaker Central / Bass Side Speaker

(No. 7) (No. 4) (No. 5) (No. 3)

2 V -- -- --

4VV----

6 VVV--

8 VVVV

* To enable Multi-Streaming function, you need to connect a front panel audio cable to the front

panel audio header. After restarting your computer, you will find “Mixer” tool on your system.

Please select “Mixer ToolBox” , click “Enable playback multi-streaming”, and click

“ok”. Choose “2CH”, “4CH”, “6CH”, or “8CH” and then you are allowed to select “Realtek HDA

Primary output” to use Rear Speaker, Central/Bass, and Front Speaker, or select “Realtek HDA

Audio 2nd output” to use front panel audio.

44

4

ASRock K8NF4G-VSTA Motherboard

1.1.

1.

IntroductionIntroduction

Introduction

Thank you for purchasing ASRock K8NF4G-VSTA motherboard, a reliable

motherboard produced under ASRock’s consistently stringent quality control. It de-

livers excellent performance with robust design conforming to ASRock’s commit-

ment to quality and endurance.

This Quick Installation Guide contains introduction of the motherboard and step-by-

step installation guide. More detailed information of the motherboard can be found in

the user manual presented in the Support CD.

Because the motherboard specifications and the BIOS software might

be updated, the content of this manual will be subject to change without

notice. In case any modifications of this manual occur, the updated

version will be available on ASRock website without further notice. You

may find the latest VGA cards and CPU support lists on ASRock

website as well.

ASRock website http://www.asrock.com

1.11.1

1.1

Package ContentsPackage Contents

Package Contents

1 x ASRock K8NF4G-VSTA Motherboard

(Micro ATX Form Factor: 9.6-in x 8.0-in, 24.4 cm x 20.3 cm)

1 x ASRock K8NF4G-VSTA Quick Installation Guide

1 x ASRock K8NF4G-VSTA Support CD

1 x Ultra ATA 66/100/133 IDE Ribbon Cable (80-conductor)

1 x 3.5-in Floppy Drive Ribbon Cable

1 x Serial ATA (SATA) Data Cable (Optional)

1 x Serial ATA (SATA) HDD Power Cable (Optional)

1 x HD 8CH I/O Shield

1 x COM Port Bracket

1 x HDMR Card (Optional)

EnglishEnglish

English

55

5

ASRock K8NF4G-VSTA Motherboard

EnglishEnglish

English

1.21.2

1.2

SpecificationsSpecifications

Specifications

Platform - Micro ATX Form Factor: 9.6-in x 8.0-in, 24.4 cm x 20.3 cm

CPU - 754-Pin Socket Supporting advanced 64-bit AMD Athlon

TM

64

and 32-bit/64-bit Sempron Processors

- Supports AMD’s Cool ‘n’ Quiet

TM

Technology

(see CAUTION 1)

- Chipset capable to FSB 1000 MHz (2.0 GT/s)

- Supports Untied Overclocking Technology (see CAUTION 2)

- Supports Hyper-Transport Technology

Chipset - Northbridge: nVidia

®

GeForce 6100

- Southbridge: nVidia

®

nForce 410 MCP

Memory - 2 x DDR DIMM slots

- Support DDR400/333/266

- Max. capacity: 2GB

Hybrid Booster - CPU Frequency Stepless Control (see CAUTION 3)

- ASRock U-COP (see CAUTION 4)

- Boot Failure Guard (B.F.G.)

Expansion Slot - 2 x PCI slots

- 1 x PCI Express x 16 slot

- 1 x PCI Express x 1 slot

- 1 x HDMR slot

Graphics - Integrated NV44 graphics DX9.0 VGA

- Pixel Shader 3.0

- Max. shared memory 128MB

Audio - Realtek ALC883 7.1 channel CODEC with High Definition

Audio

LAN - Realtek PHY RTL8201CL

- Speed: 10/100 Ethernet

- Supports Wake-On-LAN

Rear Panel I/O HD 8CH I/O

- 1 x PS/2 Mouse

- 1 x PS/2 Keyboard Port

- 1 x VGA Port

- 1 x Parallel Port (ECP/EPP Support)

- 4 x Ready-to-Use USB 2.0 Ports

- 1 x RJ-45 Port

- Audio Jack: Side Speaker/Rear Speaker/Central Bass/Line

in/Front Speaker/Microphone (see CAUTION 5)

66

6

ASRock K8NF4G-VSTA Motherboard

EnglishEnglish

English

Connector - 2 x Serial ATAII 3.0Gb/s connectors, support RAID 0, 1, JBOD

(No support for “Hot Plug” function) (see CAUTION 6)

- 2 x ATA133 IDE connectors (support 4 x IDE devices)

- 1 x Floppy connector

- 1 x IR header

- 1 x Game header

- 1 x COM port header

- CPU/Chassis FAN connector

- 20 pin ATX power connector

- 4 pin 12V power connector

- CD in header

- Front panel audio connector

- 2 x USB 2.0 headers (support 4 USB 2.0 ports)

(see CAUTION 7)

BIOS Feature - 4Mb AMI BIOS

- AMI Legal BIOS

- Supports “Plug and Play”

- ACPI 1.1 Compliance Wake Up Events

- Supports jumperfree

- SMBIOS 2.3.1 Support

Support CD - Drivers, Utilities, AntiVirus Software (Trial Version)

Hardware - CPU Temperature Sensing

Monitor - Motherboard Temperature Sensing

- CPU Overheat Shutdown to Protect CPU Life

- CPU Fan Tachometer

- Chassis Fan Tachometer

- CPU Quiet Fan

- Voltage Monitoring: +12V, +5V, +3.3V, Vcore

OS - Microsoft

®

Windows

®

2000 / XP / XP 64-bit / Vista

TM

compliant (see CAUTION 8)

Certifications - FCC, CE, WHQL

77

7

ASRock K8NF4G-VSTA Motherboard

EnglishEnglish

English

CAUTION!

1. For power-saving’s sake, it is strongly recommended to enable AMD’s Cool ‘n’

Quiet

TM

technology under Windows system. See APPENDIX on page 41 of

“User Manual” in the Support CD to enable AMD’s Cool ‘n’ Quiet

TM

technology.

Since not all K8 754-pin CPU can support AMD’s Cool ‘n’ Quiet

TM

technology,

please check AMD’s website for details.

2. This motherboard supports Untied Overclocking Technology. Please read “Un-

tied Overclocking Technology” on page 19 for details.

3. Although this motherboard offers stepless control, it is not recommended to

perform over-clocking. Frequencies other than the recommended CPU bus

frequencies may cause the instability of the system or damage the CPU.

4. While CPU overheat is detected, the system will automatically shutdown.

Before you resume the system, please check if the CPU fan on the motherboard

functions properly and unplug the power cord, then plug it back again. To

improve heat dissipation, remember to spray thermal grease between the

CPU and the heatsink when you install the PC system.

5. For microphone input, this motherboard supports both stereo and mono modes.

For audio output, this motherboard supports 2-channel, 4-channel, 6-channel,

and 8-channel modes. Please check the table on page 3 for proper connection.

6. Before installing SATAII hard disk to SATAII connector, please read the “SATAII

Hard Disk Setup Guide” on page 16 to adjust your SATAII hard disk drive to

SATAII mode. Besides, you are allowed to downgrade the SATAII hard disk to

SATA hard disk (from SATAII 3Gb/s down to SATA 1.5Gb/s), and connect it to

the SATAII connector. You can also connect SATA hard disk to SATAII connec-

tor directly.

7. Power Management for USB 2.0 works fine under Microsoft

®

Windows

®

Vista

TM

/ XP 64-bit / XP SP1 or SP2 / 2000 SP4.

8. Microsoft

®

Windows

®

Vista

TM

driver is not ready yet. We will update it to our

website in the future. Please visit our website for Microsoft

®

Windows

®

Vista

TM

driver and related information.

ASRock website http://www.asrock.com

88

8

ASRock K8NF4G-VSTA Motherboard

EnglishEnglish

English

1.31.3

1.3

Minimum Hardware RMinimum Hardware R

Minimum Hardware R

equirement Tequirement T

equirement T

able for Wable for W

able for W

indowsindows

indows

®®

®

VistaVista

Vista

TMTM

TM

Basic Logo Basic Logo

Basic Logo

For system integrators and users who purchase our motherboard and

plan to submit Windows

®

Vista

TM

Basic logo, please follow the below

table for minimum hardware requirement. Please adopt the CPU, memory,

and VGA that we suggest.

CPU Sempron 2500+

Memory 512MB Single Channel*

VGA DX9.0 with WDDM Driver

* If you use onboard VGA with total system memory size 512MB and plan to

submit Windows

®

Vista

TM

Basic logo, please adjust the shared memory size of

onboard VGA to 64MB or less than 64MB. If you use onboard VGA with total system

memory size above 512MB and plan to submit Windows

®

Vista

TM

Basic logo, the

shared memory size of onboard VGA can be adjusted up to 128MB.

99

9

ASRock K8NF4G-VSTA Motherboard

2.2.

2.

InstallationInstallation

Installation

Pre-installation PrecautionsPre-installation Precautions

Pre-installation Precautions

Take note of the following precautions before you install mother-

board components or change any motherboard settings.

1. Unplug the power cord from the wall socket before touching any

component. Failure to do so may cause severe damage to the

motherboard, peripherals, and/or components.

2. To avoid damaging the motherboard components due to static

electricity, NEVER place your motherboard directly on the car-

pet or the like. Also remember to use a grounded wrist strap or

touch a safety grounded object before you handle components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a

grounded antstatic pad or in the bag that comes with the

component.

5. When placing screws into the screw holes to secure the

motherboard to the chassis, please do not over-tighten the screws!

Doing so may damage the motherboard.

2.12.1

2.1

CPU InstallationCPU Installation

CPU Installation

Step 1. Unlock the socket by lifting the lever up to a 90° angle.

Step 2. Position the CPU directly above the socket such that the CPU corner with

the golden triangle matches the socket corner with a small triangle.

Step 3. Carefully insert the CPU into the socket until it fits in place.

The CPU fits only in one correct orientation. DO NOT force the CPU

into the socket to avoid bending of the pins.

Step 4. When the CPU is in place, press it firmly on the socket while you push

down the socket lever to secure the CPU. The lever clicks on the side tab

to indicate that it is locked.

Step 5. Install CPU fan and heatsink. For proper installation, please kindly refer to

the instruction manuals of your CPU fan and heatsink vendors.

EnglishEnglish

English

1010

10

ASRock K8NF4G-VSTA Motherboard

EnglishEnglish

English

2.22.2

2.2

Installation of Memory Modules (DIMM)Installation of Memory Modules (DIMM)

Installation of Memory Modules (DIMM)

K8NF4G-VSTA motherboard provides two 184-pin DDR (Double Data Rate) DIMM

slots.

Please make sure to disconnect power supply before adding or

removing DIMMs or the system components.

Step 1. Unlock a DIMM slot by pressing the retaining clips outward.

Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the break

on the slot.

The DIMM only fits in one correct orientation. It will cause permanent

damage to the motherboard and the DIMM if you force the DIMM into the

slot at incorrect orientation.

Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends fully

snap back in place and the DIMM is properly seated.

1111

11

ASRock K8NF4G-VSTA Motherboard

2.32.3

2.3

Expansion SlotsExpansion Slots

Expansion Slots

(PCI Express Slots, PCI Slots and HDMR Slot)(PCI Express Slots, PCI Slots and HDMR Slot)

(PCI Express Slots, PCI Slots and HDMR Slot)

There are 2 PCI Express slots, 2 PCI slots and 1 HDMR slot on K8NF4G-VSTA

motherboard.

PCIE Slots: PCIE1 (PCIE x 16 slot) is used for PCI Express cards with x16 lane

width graphics cards.

PCIE2 (PCIE x 1 slot) is used for PCI Express cards, such as

Gigabit LAN card, SATA2 card, etc.

PCI Slots: PCI slots are used to install expansion cards that have the 32-bit PCI

interface.

HDMR slot: The HDMR slot is used to insert an ASRock HDMR card with v.92

Modem functionality. The HDMR slot is shared with PCIE2 slot; you

can only choose either PCIE2 slot or HDMR slot to use.

Installing an expansion cardInstalling an expansion card

Installing an expansion card

Step 1. Before installing the expansion card, please make sure that the power

supply is switched off or the power cord is unplugged. Please read the

documentation of the expansion card and make necessary hardware

settings for the card before you start the installation.

Step 2. Remove the system unit cover (if your motherboard is already installed in

a chassis).

Step 3. Remove the bracket facing the slot that you intend to use. Keep the

screws for later use.

Step 4. Align the card connector with the slot and press firmly until the card is

completely seated on the slot.

Step 5. Fasten the card to the chassis with screws.

Step 6. Replace the system cover.

2.4 Easy Multi Monitor Feature2.4 Easy Multi Monitor Feature

2.4 Easy Multi Monitor Feature

This motherboard supports Multi Monitor upgrade. With the internal onboard VGA

and the external add-on PCI Express VGA card, you can easily enjoy the benefits

of Multi Monitor feature. If you plan to enable the function of onboard VGA, please

enter the option “Share Memory” of BIOS to adjust the memory capability to

[16MB], [32MB], [64MB], or [128MB]. Please note that the value you select should

be less than the total capability of the system memory. The default value of “Share

Memory” is [Auto], which will disable onboard VGA function when installing VGA

card. After setting up BIOS, you can install VGA cards and VGA card drivers to

enjoy multi-monitors.

EnglishEnglish

English

1212

12

ASRock K8NF4G-VSTA Motherboard

EnglishEnglish

English

the red-striped side to Pin1

2.52.5

2.5

Jumpers SetupJumpers Setup

Jumpers Setup

The illustration shows how jumpers are

setup. When the jumper cap is placed on

pins, the jumper is “Short”. If no jumper cap

is placed on pins, the jumper is “Open”. The

illustration shows a 3-pin jumper whose pin1

and pin2 are “Short” when jumper cap is

placed on these 2 pins.

Jumper Setting

PS2_USB_PW1 Short pin2, pin3 to enable

(see p.2, No. 1) +5VSB (standby) for PS/2 or

USB wake up events.

Note: To select +5VSB, it requires 2 Amp and higher standby current provided by

power supply.

Clear CMOS Jumper

(CLRCMOS2)

(see p.8, No. 11)

Note: CLRCMOS2 allows you to clear the data in CMOS. The data in CMOS includes

system setup information such as system password, date, time, and system

setup parameters. To clear and reset the system parameters to default setup,

please turn off the computer and unplug the power cord from the power

supply. After waiting for 15 seconds, use a jumper cap to short pin2 and pin3

on CLRCMOS2 for 5 seconds. However, please do not clear the CMOS right

after you update the BIOS. If you need to clear the CMOS when you just finish

updating the BIOS, you must boot up the system first, and then shut it down

before you do the clear-CMOS action.

Short Open

Clear CMOSDefault

2.6 Onboard Headers and Connectors2.6 Onboard Headers and Connectors

2.6 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place

jumper caps over these headers and connectors. Placing jumper caps

over the headers and connectors will cause permanent damage of the

motherboard!

•

Floppy Connector

(33-pin FLOPPY1)

(see p.2 No. 20)

Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the

connector.

1313

13

ASRock K8NF4G-VSTA Motherboard

connect the black end

to the IDE devices

connect the blue end

to the motherboard

80-conductor ATA 66/100/133 cable

Primary IDE Connector (Blue) Secondary IDE Connector (Black)

(39-pin IDE1, see p.2 No. 7) (39-pin IDE2, see p.2 No. 6)

Note: If you use only one IDE device on this motherboard, please set the IDE

device as “Master”. Please refer to the instruction of your IDE device vendor

for the details. Besides, to optimize compatibility and performance, please

connect your hard disk drive to the primary IDE connector (IDE1, blue) and

CD-ROM to the secondary IDE connector (IDE2, black).

Serial ATA II Connectors These Serial ATA II (SATA II)

(SATA II_1: see p.2, No. 13) connectors support SATA II

(SATA II_2: see p.2, No. 12) or SATA hard disk for internal

storage devices. The current

SATA II interface allows up to

3.0 Gb/s data transfer rate.

Serial ATA (SATA) Either end of the SATA data cable

Data Cable can be connected to the SATA /

SATAII hard disk or the SATAII

connector on the motherboard.

SATAII_2

SATAII_1

Serial ATA (SATA) Please connect the black end of

Power Cable SATA power cable to the power

(Optional) connector on each drive. Then

connect the white end of SATA

power cable to the power

connector of the power supply.

USB 2.0 Header HD 8CH I/O accommo-

(9-pin USB67) dates 4 default USB 2.0 ports. If

(see p.2 No. 17) those USB 2.0 ports on the I/O

panel are not sufficient, this

USB 2.0 header is available to

support 2 additional USB 2.0

ports.

connect to the

power supply

connect to the SATA

HDD power connector

EnglishEnglish

English

1414

14

ASRock K8NF4G-VSTA Motherboard

EnglishEnglish

English

CD1

USB 2.0 Header HD 8CH I/O accommo-

(9-pin USB45) dates 4 default USB 2.0 ports. If

(see p.2 No. 19) those USB 2.0 ports on the I/O

panel are not sufficient, this

USB 2.0 header is available to

support 2 additional USB 2.0

ports.

Infrared Module Header This header supports an

(5-pin IR1) optional wireless transmitting

(see p.2 No. 18) and receiving infrared module.

Internal Audio Connectors This connector allows you

(4-pin CD1) to receive stereo audio input

(CD1: see p.2 No. 27) from sound sources such as

a CD-ROM, DVD-ROM, TV

tuner card, or MPEG card.

Front Panel Audio Header This is an interface for the front

(9-pin HD_AUDIO1) panel audio cable that allows

(see p.9, No. 25) convenient connection and

control of audio devices.

1. High Definition Audio supports Jack Sensing, but the panel wire on the

chassis must support HDA to function correctly. Please follow the

instruction in our manual and chassis manual to install your system.

2. If you use AC’97 audio panel, please install it to the front panel audio

header as below:

A. Connect Mic_IN (MIC) to MIC2_L.

B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.

C. MIC_RET and OUT_RET are for HD audio panel only. You don’t

need to connect them for AC’97 audio panel.

D. Enter BIOS Setup Utility. Enter Advanced Settings, and then select

Chipset Configuration. Set the Front Panel Control option from

[Auto] to [Enabled].

E. Enter Windows system. Click the icon on the lower right hand

taskbar to enter Realtek HD Audio Manager. Click “Audio I/O”, select

“Connector Settings” , choose “Disable front panel jack

detection”, and save the change by clicking “OK”.

1515

15

ASRock K8NF4G-VSTA Motherboard

System Panel Header This header accommodates

(9-pin PANEL1) several system front panel

(see p.2 No. 15) functions.

Chassis Speaker Header Please connect the chassis

(4-pin SPEAKER 1) speaker to this header.

(see p.2 No. 16)

Chassis Fan Connector Please connect a chassis fan

(3-pin CHA_FAN1) cable to this connector and

(see p.2 No. 14) match the black wire to the

ground pin.

CPU Fan Connector Please connect the CPU fan

(4-pin CPU_FAN1) cable to this connector and

(see p.2 No. 30) match the black wire to the

ground pin.

ATX Power Connector Please connect an ATX power

(20-pin ATXPWR1) supply to this connector.

(see p.2 No. 28)

ATX 12V Power Connector Please note that it is necessary

(4-pin ATX12V1) to connect a power supply with

(see p.2 No. 2) ATX 12V plug to this connector.

Failing to do so will cause power

up failure.

Game Port Header Connect a Game cable to this

(15-pin GAME1) header if the Game port bracket

(see p.2 No. 22) is installed.

Serial port Header This COM1 header

(9-pin COM1) supports a serial port module.

(see p.2 item 29)

EnglishEnglish

English

1616

16

ASRock K8NF4G-VSTA Motherboard

EnglishEnglish

English

2.72.7

2.7

SASA

SA

TT

T

AII Hard Disk Setup GuideAII Hard Disk Setup Guide

AII Hard Disk Setup Guide

Before installing SATAII hard disk to your computer, please carefully read below

SATAII hard disk setup guide. Some default setting of SATAII hard disks may not be

at SATAII mode, which operate with the best performance. In order to enable SATAII

function, please follow the below instruction with different vendors to correctly

adjust your SATAII hard disk to SATAII mode in advance; otherwise, your SATAII hard

disk may fail to run at SATAII mode.

Western Digital

If pin 5 and pin 6 are shorted, SATA 1.5GB/s will be enabled.

On the other hand, if you want to enable SATAII 3.0GB/s, please remove the jumpers

from pin 5 and pin 6.

SAMSUNG

If pin 3 and pin 4 are shorted, SATA 1.5GB/s will be enabled.

On the other hand, if you want to enable SATAII 3.0GB/s, please remove the jumpers

from pin 3 and pin 4.

HITACHI

Please use the Feature Tool, a DOS-bootable tool, for changing various ATA features.

Please visit HITACHI’s website for details:

http://www.hitachigst.com/hdd/support/download.htm

The above examples are just for your reference. For different SATAII hard

disk products of different vendors, the jumper pin setting methods may not

be the same. Please visit the vendors’ website for the updates.

1717

17

ASRock K8NF4G-VSTA Motherboard

EnglishEnglish

English

2.8 Serial A2.8 Serial A

2.8 Serial A

TT

T

A (SAA (SA

A (SA

TT

T

A) / Serial AA) / Serial A

A) / Serial A

TT

T

AII (SAAII (SA

AII (SA

TT

T

AII) Hard DisksAII) Hard Disks

AII) Hard Disks

Installation Installation

Installation

This motherboard adopts nVidia

®

nForce 410 MCP southbridge chipset that

supports Serial ATA (SATA) / Serial ATAII (SATAII) hard disks and RAID functions.

You may install SATA / SATAII hard disks on this motherboard for internal storage

devices. This section will guide you to install the SATA / SATAII hard disks.

STEP 1: Install the SATA / SATAII hard disks into the drive bays of your chassis.

STEP 2: Connect the SATA power cable to the SATA / SATAII hard disk.

STEP 3: Connect one end of the SATA data cable to the motherboard’s SATAII

connector.

STEP 4: Connect the other end of the SATA data cable to the SATA / SATAII hard

disk.

2.92.9

2.9

HDMR Card Driver InstallationHDMR Card Driver Installation

HDMR Card Driver Installation

When you install the drivers to your system, please make sure to install Realtek

Audio driver before installing HDMR card driver; for other drivers installation,

please follow the driver order in our support CD. It is suggested to install Win-

dows

®

OS, Realtek Audio and HDMR drivers with the HDMR card inserted to this

motherboard; in this way, there is no problem on the Audio CODEC function.

However, if you install Windows

®

XP 64-bit OS without HDMR card inserted and

plan to insert the HDMR card to this motherboard, please install the Realtek Audio

driver again; otherwise, the Audio CODEC will not work. If you install Windows

®

2000 / XP OS without HDMR card inserted and plan to insert the HDMR card to this

motherboard, you just have to restart your computer, then the Audio CODEC can

work successfully.

1818

18

ASRock K8NF4G-VSTA Motherboard

EnglishEnglish

English

2.102.10

2.10

Installing WindowsInstalling Windows

Installing Windows

®

2000 / Windows 2000 / Windows

2000 / Windows

®

XP / Windows XP / Windows

XP / Windows

®

XP 64-bit / WindowsXP 64-bit / Windows

XP 64-bit / Windows

®

Vista Vista

Vista

TMTM

TM

Without RAID Functions Without RAID Functions

Without RAID Functions

If you just want to install Windows

®

2000, Windows

®

XP, Windows

®

XP 64-bit or

Windows

®

Vista

TM

on your SATA / SATAII HDDs without RAID functions, you don’t

have to make a SATA / SATAII driver diskette. Besides, there is no need for you to

change the BIOS setting. You can start to install Windows

®

2000, Windows

®

XP,

Windows

®

XP 64-bit or Windows

®

Vista

TM

on your system directly.

2.112.11

2.11

Installing WindowsInstalling Windows

Installing Windows

®

2000 / Windows 2000 / Windows

2000 / Windows

®

XP / Windows XP / Windows

XP / Windows

®

XP 64-bit / WindowsXP 64-bit / Windows

XP 64-bit / Windows

®

Vista Vista

Vista

TMTM

TM

With RAID Functions With RAID Functions

With RAID Functions

If you want to install Windows

®

2000, Windows

®

XP, Windows

®

XP 64-bit or Windows

®

Vista

TM

on your SATA / SATAII HDDs with RAID functions, please follow the below

steps.

STEP 1: Make a SATA / SATAII Driver Diskette.

A. Insert the ASRock Support CD into your optical drive to boot your system.

B. During POST at the beginning of system boot-up, press <F11> key, and

then a window for boot devices selection appears. Please select CD-

ROM as the boot device.

C. When you see the message on the screen, “Do you want to generate

Serial ATA driver diskette [YN]?”, press <Y>.

D. Then you will see these messages,

Please insert a diskette into the floppy drive.

WARNING! Formatting the floppy diskette will

lose ALL data in it!

Start to format and copy files [YN]?

Please insert a floppy diskette into the floppy drive, and press <Y>.

E. The system will start to format the floppy diskette and copy SATA /

SATAII drivers into the floppy diskette.

STEP 2: Set Up BIOS.

A. Enter BIOS SETUP UTILITY Advanced screen IDE Configuration.

B. Set the “SATAII Operation Mode” option from [non-RAID] to [RAID].

STEP 3: Use “RAID Installation Guide” to set RAID configuration.

Before installing Windows

®

2000 to your system, your disk is supposed to

include SP4. If there is no SP4 included in your disk, please visit the below

website for proper procedures of making a SP4 disk:

http://www.microsoft.com/Windows2000/downloads/servicepacks/sp4/

spdeploy.htm#the_integrated_installation_fmay

1919

19

ASRock K8NF4G-VSTA Motherboard

EnglishEnglish

English

After step1, 2, 3, you can start to install Windows

®

2000 / Windows

®

XP / Windows

®

XP 64-bit / Windows

®

Vista

TM

.

NOTE. If you install Windows

®

2000 / Windows

®

XP / Windows

®

XP 64-bit / Windows

®

Vista

TM

on IDEHDDs and want to manage (create, convert, delete, or rebuild) RAID functions

on SATA / SATAII HDDs, you still need to set up “SATAII Operation Mode” to [RAID]

first. Then, please set the RAID configuration by using “RAID Utility for Windows

Guide” in Windows

®

environment. Please refer to the document in the Support CD,

“Guide to nVidia RAID Utility for Windows”, which is located in the folder at the

following path:

.. \Information\Manual\RAID Utility for Windows Guide

2.122.12

2.12

Untied Overclocking TUntied Overclocking T

Untied Overclocking T

echnologyechnology

echnology

This motherboard supports Untied Overclocking Technology, which means during

overclocking, FSB enjoys better margin due to fixed PCI / PCIE buses. Before you

enable Untied Overclocking function, please enter “Overclock Mode” option of BIOS

setup to set the selection from [Auto] to [CPU, PCIE, Async.]. Therefore, CPU FSB is

untied during overclocking, but PCI and PCIE buses are in the fixed mode so that FSB

can operate under a more stable overclocking environment.

Before you start to configure the RAID function, you need to

check the installation guide in the Support CD for proper configuration.

Please refer to the document in the Support CD, “Guide to SATA Hard

Disks Installation and RAID Configuration”, which is located in the folder

at the following path:

.. \Information\Manual\RAID Installation Guide

2020

20

ASRock K8NF4G-VSTA Motherboard

3. BIOS Information3. BIOS Information

3. BIOS Information

The Flash Memory on the motherboard stores BIOS Setup Utility. When you start up

the computer, please press <F2> during the Power-On-Self-Test (POST) to enter

BIOS Setup utility; otherwise, POST continues with its test routines. If you wish to

enter BIOS Setup after POST, please restart the system by pressing <Ctl> + <Alt> +

<Delete>, or pressing the reset button on the system chassis.

The BIOS Setup program is designed to be user-friendly. It is a menu-driven program,

which allows you to scroll through its various sub-menus and to select among the

predetermined choices. For the detailed information about BIOS Setup, please refer

to the User Manual (PDF file) contained in the Support CD.

4. Software Suppor4. Software Suppor

4. Software Suppor

t CD informationt CD information

t CD information

This motherboard supports various Microsoft

®

Windows

®

operating systems: 2000 /

XP / XP 64-bit / Vista

TM

. The Support CD that came with the motherboard contains

necessary drivers and useful utilities that will enhance motherboard features.

To begin using the Support CD, insert the CD into your CD-ROM drive. It will display

the Main Menu automatically if “AUTORUN” is enabled in your computer. If the Main

Menu does not appear automatically, locate and double-click on the file “ASSETUP.

EXE” from the “BIN” folder in the Support CD to display the menus.

EnglishEnglish

English

La page charge ...

ASROCK K8NF4G-VSTA Le manuel du propriétaire

ASROCK K8NF4G-VSTA Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents