Lightspeed Topcat Guide d'installation

Catégorie
Équipement musical supplémentaire
Taper
Guide d'installation
Installation Guide
Instructional Audio System
Topcat
2
1. Do not use the apparatus near water.
2. Clean only with dry cloth.
3. Do not block any ventilation openings.
4. Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.
5. Do not defeat the safety purpose of the polarized or grounding-type plug.
A polarized plug has two blades with one wider than the other. A grounding- type
plug has two blades and a third grounding prong. The wide blade or the third prong
is provided for your safety. If the provided plug does not fit into your outlet, consult
an electrician for replacement of the outlet.
6. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
7. Unplug this apparatus during lightning storms or when unused for long periods of
time.
8. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.
9. When the mains plug or appliance coupler is used as the disconnect device, it shall
remain readily operable.
10. Please keep the unit in a good ventilation environment.
11. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus
to rain or moisture.
12. Apparatus shall not be exposed to dripping or splashing and no objects filled with
liquids, such as vases, shall be placed on the apparatus.
13. WARNING: Battery pack shall not be exposed to excessive heat such as sunshine,
fire or the like.
Important Safety Instructions
OVERVIEW
Table of Contents
OVERVIEW
2 Important Safety Instructions
4 System Components and Unpacking
5 Optional Components
INSTALLATION
6 Installation Planning
6 Selecting Mounting Location
7 Topcat Ceiling Installation (U.S. & Canada)
9 Topcat Ceiling Installation (Outside U.S. & Canada)
12 Installing and Wiring Electrical Power
14 Alternate Power Connections
15 Setup and Using the Flexmike
16 Charging the Flexmike
INSTALLING OPTIONAL EQUIPMENT
17 PageFirst Installation
20 Media Connector Set-Up
24 Audio Input Cable Installation
CERTIFICATIONS & TROUBLESHOOTING
25 Safety Warnings and Certifications
28 Troubleshooting
OVERVIEWINSTALLATIONOPTIONAL INSTALLATIONTROUBLESHOOTING
4
System Components and Unpacking
The standard configuration includes:
Microphone Cradle Charger
& Power Supply
Flexmike
Volume Control Microphone
Topcat
OVERVIEW
NOTE ON PAIRING: Topcat, microphone(s), and Media Connector or Activate Station are paired together at the Lightspeed factory as required for proper operation.
5
OVERVIEWINSTALLATIONOPTIONAL INSTALLATIONTROUBLESHOOTING
Sharemike
Handheld Microphone
Optional Components
Media Connector
& Power Supply
Audio
Input
Audio
Output
Tone
Level
Push
StatusPower
Media
Media
Connector
Connector
Activate Station
with Bluetooth
PowerLink
InputOutputMic
Optional equipment which may be part of your Topcat system:
6
INSTALLATION
SELECTING MOUNTING LOCATION
The Topcat is shipped ready to mount in a standard suspended ceiling grid. All hardware
needed to secure the Topcat into the ceiling grid is provided. Additional hardware may be
required if building structure tie-points are metal. A licensed electrician will need to provide
necessary materials if Topcat is permanently connected to the building AC mains.
Topcat will distribute sound throughout a classroom of up to 1200 sq  (112 sq m) with ceiling
heights of 9 to 12 . The location of the Topcat is critical to ensure even sound distribution.
1. Identify the center of the listening area of the classroom for optimum location (Figure 1).
2. Select a ceiling tile that is free of fixtures (lighting, HVAC, etc.) nearest to the center point.
3. Remove the selected ceiling tile for Topcat installation.
FIGURE 1:
IDENTIFY THE CENTER
OF THE LISTENING AREA
TOOLS AND MATERIALS
In addition to the contents of the Topcat system, you may need the following tools & materials:
Flat blade screwdriver (small)
Pliers
Wire cutters
Drill
Before beginning installation, make sure you have the necessary tools and materials on hand and that the area underneath the proposed Topcat location is cleared.
Installation Planning
NOTE: Topcat is designed for installation in a 2’ x 2’ or 2’ x 4’ suspended ceiling grid (or 600mm x 600mm international ceiling grids). If you do not have this type of ceiling,
please contact your local Lightspeed Territory Manager.
Utility knife
Safety wire anchors
Wire ties
7
OVERVIEWINSTALLATIONOPTIONAL INSTALLATIONTROUBLESHOOTING
FIGURE 3:
SNAP THE T-BAR INTO PLACE TO CREATE A
1’ X 2’ OPENING AND A 3’ X 2’ OPENING
NEW T-BAR
EXISTING TILE GRID
3/4 TILE
TCQ
END SIDE
TOPCAT CEILING INSTALLATION (U.S. & CANADA)
The dimensions of Topcat are 1’ x 2’ and it is designed to fit into any
standard 2’ x 2’ or 2’ x 4’ suspended ceiling tile grid.
1. The ceiling tile will need to be cut to accommodate Topcat.
2. Set the ceiling tile on a flat work surface with the patterned side
facing down.
3. Using a straight edge, cut a 1’ x 2’ section from the ceiling tile,
leaving a 1’ x 2’ section and a 2’ x 3’ section (Figure 2), or two 1’ x 2’
sections (Figure 4).
5. Topcat dimensions
FIGURE 2:
CUT THE 2’ X 4’ TILE TO CREATE A 1’ X 2’
SECTION AND A 2’ X 3’ SECTION
WASTE REMAINING
3/4 CEILING TILE
CUT WITH
STRAIGHT EDGE
1’ 3’
2’
4’
2’ X 4’ CEILING TILE
FIGURE 4:
CUT THE 2’ X 2’ TILE TO CREATE
TWO 1’ X 2’ SECTIONS
WASTE
CUT WITH
STRAIGHT EDGE
1' 1'
2’
2'
2’ X 2’ CEILING TILE
NEW T-BAR
EXISTING TILE GRID
1/2 TILE
FIGURE 5:
SNAP THE T-BAR INTO PLACE TO
CREATE TWO 1’ X 2’ OPENINGS
TCQ
4. Locate the 2’ ceiling grid T-bar provided. Locate the attachment
slots in the existing ceiling grid and snap the new T-bar into
place to create two openings to create a 1’ x 2’ and a 2’ x 3’
opening (Figure 3) or two 1’ x 2’ openings (Figure 5).
+
DC INPUT
24V/2.5A
PAGING
INPUT
AUDIO IN REGISTERPROGRAM
-
DO NOT DRILL IN THIS AREA
L
3.75”
11.5” 23 3/8”
8
FIGURE 1:
LOOP THE SAFETY WIRE THROUGH TAB
FIGURE 2:
PLACE TOPCAT INTO THE CEILING
GRID AND LOOP THE SAFETY WIRE
THROUGH BOTH TABS
CEILING
SECURING TOPCAT (U.S. & CANADA)
To comply with Building Codes, the Topcat MUST be secured with two
safety wires.
1. Locate the 20  length of safety wire. The safety wire needs to be permanently
attached to the solid building structure above.
2. Cut the safety wire in half, leaving two 10  pieces.
3. Install anchors (or eye screws if necessary) into the building structure.
4. Loop one end of the safety wire through the anchor (or eye screw), then twist it
around itself at least five times (Figure 1). Repeat for second anchor.
5. Li the Topcat up and lay it into the desired ceiling grid location.
CAUTION: Ensure that Topcat is stable on the grid rails with the side brackets
hooked over the rails. If not stable, there could be a danger of it falling until
safety wires are attached.
6. Loop the other end of the safety wire through one of the tabs on Topcat (located
in opposite corners). Pull the wire through until it is taut and twist it around itself
at least five times to secure Topcat. Cut o excess wire if needed.
7. When hard wiring AC power to Topcat, electrical codes require for Topcat to
be attached to the ceiling rail. Utilizing existing holes on the vertical section of
the ceiling rail (center of the hole to the base of the rail must be a minimum of
15mm) drill two screws on each 2’ side of the Topcat. Drilling these screws into
the designated areas of the Topcat chassis will not cause harm to the product
(Figure 3).
NOTE: Do not drill in the area designated with yellow tape.
8. Continue to page 12, Installing and Wiring Electrical Power.
FIGURE 4:
DRILL SCREWS THROUGH CEILING RAIL INTO DESIGNATED AREAS OF TOPCAT
ANCHOR OR
EYE SCREW
9
OVERVIEWINSTALLATIONOPTIONAL INSTALLATIONTROUBLESHOOTING
TOPCAT CEILING INSTALLATION (OUTSIDE U.S. & CANADA)
For 600mm x 600mm Ceiling Grid
Topcat has spacer brackets mounted on each of the four sides. With
these brackets installed and the ceiling tile is cut in half, the Topcat will
fit into a standard 2’ x 2’ suspended ceiling grid with an additional tile
support. With the brackets removed, it will fit a 300mm x 600mm ceiling
grid with an additional tile support (Figures 4 & 5).
Remove the spacer brackets from each of the four sides of the Topcat
(Figure 1, next page).
NOTE: If your ceiling grid is any other dimension than mentioned above,
contact your local Lightspeed Representative.
FIGURE 2
SNAP THE T-BAR INTO PLACE TO CREATE
A 1’ X 2’ OPENING AND A 3’ X 2’ OPENING
NEW T-BAR
EXISTING TILE GRID
3/4 TILE
TCQ
FIGURE 1
CUT THE 2’ X 4’ TILE TO CREATE A 1’ X 2’
SECTION AND A 2’ X 3’ SECTION
WASTE REMAINING
3/4 CEILING TILE
CUT WITH
STRAIGHT EDGE
1’ 3’
2’
4’
FIGURE 3:
CUT THE 2’ X 2’ TILE TO CREATE
TWO 1’ X 2’ SECTIONS
WASTE
CUT WITH
STRAIGHT EDGE
1' 1'
2’
2'
NEW T-BAR
EXISTING TILE GRID
1/2 TILE
FIGURE 4:
SNAP THE T-BAR INTO PLACE TO
CREATE TWO 1’ X 2’ OPENINGS
TCQ
2’ X 4’ CEILING TILE
2’ X 2’ CEILING TILE
10
To comply with Building Codes, the Topcat MUST be secured with two
safety wires and to the ceiling grid with four screws.
1. Remove the spacer brackets from each of the four sides of Topcat (Figure 1).
2. Locate the 6m length of safety wire. The safety wire needs to be permanently
attached to the solid building structure above.
3. Cut the 6m safety wire in half, leaving two 3m pieces.
4. Install anchors (or eye screws if necessary) into the building structure.
5. Loop one end of the safety wire through the anchor (or eye screw), then twist it
around itself at least five times (Figure 2). Repeat for second anchor.
6. Li the Topcat up and lay it into the desired ceiling grid location.
CAUTION: Ensure that Topcat is stable on the grid rails. If not stable there
could be a danger of it falling until safety wires are attached.
7. Loop the other end of the safety wire through one of the tabs on Topcat
(located in opposite corners). Pull the wire through until it is taut and twist it
around itself at least five times to secure Topcat. Cut o any excess wire if needed
(Figure 3).
SECURING TOPCAT (OUTSIDE U.S. & CANADA)
FIGURE 1:
REMOVE SPACER BRACKETS
FIGURE 2:
LOOP THE SAFETY WIRE THROUGH TAB
FIGURE 3:
PLACE TOPCAT INTO THE CEILING
GRID AND LOOP THE SAFETY WIRE
THROUGH BOTH TABS
CEILING
ANCHOR OR
EYE SCREW
11
OVERVIEWINSTALLATIONOPTIONAL INSTALLATIONTROUBLESHOOTING
FIGURE 7:
DRILL SCREWS THROUGH CEILING GRID INTO DESIGNATED AREAS OF TOPCAT
FIGURE 6:
DRILL SCREWS INTO THE CEILING RAIL
O.6” MIN
(15MM)
SECURING TOPCAT (OUTSIDE U.S. & CANADA)
8. Locate the four self-drilling sheet metal screws (use #8 X 3/4” only).
9. Utilizing existing holes on the vertical section of the ceiling rail (center of the hole
to the base of the rail must be a minimum of 15mm, drill two screws on each 0.6m
side of Topcat (Figure 6).
NOTE: Do not drill in the area designated with yellow tape.
10. When hard wiring AC power to Topcat, electrical codes require Topcat to be
attached to the ceiling rail.
NOTE: Drilling these screws into the designated areas of Topcat chassis will not
cause harm to the product (Figure 7).
11. Continue to page 12, Installing and Wiring Electrical Power.
12
TO BUILDING AC
POWER MAINS
INSTALLING AND WIRING ELECTRICAL POWER
There are two methods of providing power for the Topcat.
1. New Construction Installations: Connect directly to the building’s AC mains.
2. Retrofit installations: Wire to the building mains or order the optional extension
cable (Part #DCPEX-NA in U.S. and Canada; DCPEX-INT outside U.S. and Canada).
SUPPLY POWER TO THE SELECTED LOCATION
WARNING! USE A LICENSED ELECTRICIAN FOR POWER CONNECTIONS.
The Topcat System uses standard 100 – 240VAC power. Obtain the services of a licensed
electrician when supplying and connecting power to the Topcat chassis. Be sure
electrical installation complies with local building codes. Improperly installing and / or
connecting power to the system may result in EQUIPMENT DAMAGE, serious INJURY
and / or DEATH.
When routing power to Topcat, avoid interference with lighting and other noise
possibilities.
CAUTION: These servicing instructions are for use by qualified service personnel
only. To reduce the risk of electric shock, do not perform any servicing other than
that contained in the operating instructions unless you are qualified to do so.
Wire AC power to Topcat as follows:
1. Turn o the circuit at the main breaker. The all-pole main breaker shall be
incorporated in the electrical installation of the building. Using copper wire attach
the electrical wiring to the Topcat ceiling module as shown.
2. Find the power conduit hole on the Topcat back can and remove the plastic plug.
Insert the mains electrical wire through the hole (Figure 1).
3. Open the front panel door on Topcat by sliding the door toward the end of Topcat
to disengage the lock (Figure 2).
NOTE: Be careful not to damage flat speaker panel.
FIGURE 2
FIGURE 1
ATTENTION INSTALLER:
!
13
OVERVIEWINSTALLATIONOPTIONAL INSTALLATIONTROUBLESHOOTING
POWER SUPPLY
TO BUILDING
AC POWER MAINS
90V
TO
260V
INSTALLING AND WIRING ELECTRICAL POWER CONT’D
4. Remove the lid to the internal electrical box by loosening the two screws and
sliding the lid out (Figure 3).
5. Attach the ground wire to the grounding lug provided. Attach the remaining
two wires to the terminal block screws as shown.
6. Replace the cover on the internal electrical box and turn the electrical circuit
back on at the main breaker.
INTERNAL
ELECTRICAL BOX
100VAC
~240VAC
TO
POWER
SUPPLY
L1
L2
LABEL P/N:334-0081-00
GND GND
14
ALTERNATE POWER CONNECTIONS
When electrical AC power is not available above the ceiling for installation with Topcat,
there is an alternative method for supplying power to Topcat.
NOTE: There are two DC power connectors for connecting power to Topcat. Both
connectors perform the same function. Use the internal DC power connector located on
the amplifier module when AC power is connected directly to Topcat. Use the connector
access located on the outside of Topcat when using the optional DC extension cable.
1. Remove the factory installed 24V 2.5 amp power supply by unstrapping the velcro
holding it in place. Disconnect the AC power plug and the DC output cable. Then
restrap the velcro strips and enclose the AC plug with the velcro to keep it in place.
This AC plug should not touch the flat panel speaker when the door is closed.
NOTE: The 24V power supply brick must be placed in the room below the
suspended ceiling. Faceplates and electrical boxes should be provided by the
installer as required.
2. Find the 50’ DC extension cable and plug the female connector into the 24V 2.5 amp
port on Topcat. Use the wire anchor supplied with the cable to secure the cable to
the side of Topcat chassis.
NOTE: The 50’ DC extension cable is plenum rated, suitable for air handling spaces.
3. Route the DC extension cable across the ceiling and to the closest standard AC
power outlet. Cable routing should follow all local electrical codes and installation
procedures. (If the DC extension cable is to be run inside the wall, install a mud ring
or electrical box in the wall close to the AC power outlet.
If the DC extension cable is run on the surface of the wall using wire molding,
mount a surface-mount electrical box to house the connection of the DC
extension cable and the power supply.
4. Plug the DC extension cable end of the 24V supply into the power extender cable.
5. Plug the AC power cord into the power supply and into a standard AC outlet.
6. When power is applied to the Topcat, it will automatically power on.
7. Aer wiring electrical power is complete, close door securely by applying pressure
outward on the tabs located on the main body of the Topcat. Then slide the door
toward the middle of the unit and lock into place.
Power
24v/2.5a
InputOutput
Audio
analog input
Topcat audio link
Program
Page
First
Relay
Input
Contact
Closure
50 FT (15M)
DC EXTENSION CABLE
24V 2.5 AMP
POWER SUPPLY
24V 2.5 AMP PORT
15
OVERVIEWINSTALLATIONOPTIONAL INSTALLATIONTROUBLESHOOTING
SETUP AND USING THE FLEXMIKE
NOTE: This procedure is easier with two people.
1. Ensure that Topcat is powered on. The white LED on will glow.
2. Remove the Flexmike from the cradle charger. Flexmike will automatically power on and
mute when it is removed from the charger.
3. Fasten the Flexmike lanyard around the neck by connecting the magnetic clasps. Adjust
the lanyard so that the top of the microphone is at the collarbone.
4. While speaking in a normal voice, fine-tune the microphone volume by adjusting the up or
down buttons on the microphone.
Your voice should be clearly heard by another person on the other side of the room.
You should barely be able to hear your own voice.
There should not be any audio “feedback” or squealing outside of 2-3 feet
(if there is, turn the volume down slightly).
5. Once initial volume level is set, walk around the room and listen for overall audio quality.
6. The teacher can now use the controls on the Flexmike to adjust the volume level from
anywhere in the room.
7. Repeat step 6 for a second Flexmike, if purchased.
8. If a Sharemike was purchased, set the Sharemike volume.
TIPS TO OBTAIN OPTIMUM AUDIO PERFORMANCE
Speak in a natural voice. A normal conversational speech level will provide an adequate
signal. It is not necessary to increase the intensity of your voice—the audio system provides
adequate amplification (approximately 5 – 10 dB) above ambient room noises.
Avoid wearing jewelry that may rub or bump against the microphone.
Mute the Flexmike during private conversations by momentarily pressing the power button.
When muted, the blue light turns white.
When the conversation is over, unmute the Flexmike by momentarily pressing the power
button again. The white light will turn blue.
Recharge microphone(s) each night. When recharged nightly, the microphone will last
through a typical school day.
VOLUME
CONTROL
POWER / MUTE BUTTON
& STATUS LIGHT
16
CHARGING THE FLEXMIKE
Before use, the Flexmike should be charged. It will take 5-6 hours for the Flexmike
to obtain a full charge. A fully charged Flexmike will last for up to 8 hours of use. If
microphones are used daily, they should be charged each night.
When properly inserted into a cradle charger the red light on the Flexmike power button
indicates the battery pack is charging. The power status light will glow green to indicate
that charging is complete and a full charge has been reached.
Replacement Lithium Ion battery packs may only be purchased through Lightspeed
Technologies (part #L3.7V).
ATTACH LANYARD
Hang the Flexmike on the lanyard opposite
the magnetic clasp.
CONNECT CRADLE CHARGER
Plug power cord into the cradle charger and
then plug the AC end into an electrical outlet.
CHARGE MICROPHONE
Place the Flexmike into the cradle. The LED on
the Flexmike power status light will glow red
indicating charging has started.
If Activate speaker pods were purchased
with your Topcat system, the Flexmike will
be charged in the Activate Charging Station.
Please see the ACT User Manual for instruction.
17
OVERVIEWINSTALLATIONOPTIONAL INSTALLATIONTROUBLESHOOTING
PageFirst Installation
LOCATE PAGING SPEAKER AND SENSOR CLIP
If possible, the paging sensor should be hung around the 8-ohm lead wires that are
connected directly to the speaker. If it is a sealed ceiling speaker where only the 70-volt
wire is accessible, connect to the exposed 70-volt wires.
1. Locate the paging speaker in the classroom.
NOTE: PageFirst does not work with telephone or IP-based intercom systems.
2. Locate the PageFirst sensor clip. This clip is designed to hang around the wire
connected to the paging speaker. Through induction, it detects the audio signal as
it comes through the wire.
CONNECTING SENSOR TO SPEAKER WIRE
1. Gain access to the back of the speaker either up in the ceiling or on the wall.
NOTE: There is no need to disconnect any wires.
2. Unclip and open the top loop of the PageFirst sensor. Hang it around one of the
lead wires connected to the paging speaker and clip it back together (Figure 1).
INSTALLING OPTIONAL EQUIPMENT
The following components are included when the
PageFirst option is purchased as an add-on:
PageFirst sensor clip with wire pigtail (PFSC)
50’ length of shielded plenum wire
FIGURE 2:
CONNECTING PAGEFIRST TO AMPLIFIER
Power
24v/2.5a
InputOutput
Audio
analog input
Topcat audio link
Program
Page
First
Relay
Input
Contact
Closure
FIGURE 1:
HANGING THE SENSOR CLIP
18
PageFirst Installation CONTD
CONNECTING THE PAGEFIRST SENSOR TO THE TOPCAT
The sensor needs to be hard-wired back to the Topcat.
1. Insert the euro-block connector of the wire into the PageFirst input jack on the
Topcat. Secure with a screw driver by tightening the screw on the le and right
sides of the terminals (Figure 2, previous page).
2. Route the wire from the Topcat to the paging speaker.
NOTE: when routing wire, make sure to secure the wire to the building structure, as
electrical and building codes require.
3. Connect the pigtail of the sensor clip to the length of wire, using the provided wire
nuts. Coil and secure excess wire as needed.
NOTE: wire can be cut and stripped to the appropriate length if necessary.
TESTING PAGEFIRST
A page will need to be broadcast through the system to verify PageFirst is properly
sensing the audio signal.
1. Turn on the system and begin speaking.
2. Broadcast a page through the central paging system.
3. The Topcat should mute as the page is broadcast. When the broadcast is over, the
Topcat should amplify the mic as normal.
4. While walking around the room, continue talking into the microphone. Verify that
the system is not muting during times there is no page being broadcast.
ADJUSTING THE SENSITIVITY
1. If the system does not mute while the page is being broadcast, turn the sensitivity
adjustment up by turning the ADJ knob clockwise and test again.
2. If the system mutes during times when a page is not being broadcast, turn the
sensitivity down by turning the ADJ knob counterclockwise, and test again.
3. If the system experiences dropout, turn the sensitivity down by turning the ADJ
knob counterclockwise, and test again.
NOTE: The PageFirst function works via current induction. The above instructions represent the most common method to achieve suicient induction. If suicient induction is not
achieved to trigger this function, please contact Lightspeed regarding alternate installation methods.
Take precautions as necessary to prevent and guard against electromagnetic and electrostatic noise interference. Unshielded and/ or poorly shielded cable, multiple ground
paths and improper grounding may all contribute to the production of a low frequency noise which could result in the PageFirst clip muting incorrectly.
19
OVERVIEWINSTALLATIONOPTIONAL INSTALLATIONTROUBLESHOOTING
TO TRIGGER ALERT, PRESS
VOLUME UP AND DOWN
BUTTONS FOR 3 SECONDS
Additional Life Safety Solutions
RELAY INPUT
Topcat contains an input connection to detect a signal from Fire Alarm, IP Paging
System or other device. When triggered, audio from Topcat is muted to ensure
emergency alerts from external systems can be heard.
The Relay Input can be triggered with DC voltage between .5V and 24V that can be
provided from fire alarm systems and control systems with powered relay switches.
CONTACT CLOSURE
If your building is equipped with an alert notification system, teachers can use the
Flexmike microphone to send an alert.
This activates the contact closure function on Topcat, which external systems
use to perform a prescribed action, such as notifying the appropriate parties of a
classroom alert.
The Contact Closure is a normally open relay that can be closed by pressing the
up and down volume buttons at the same time for 3 seconds on the Flexmike.
Partner Interface
Relay
ComNO
Relay
Input
Page
First
Contact
Closure
20
Media Connector Set-Up
DETERMINE SET-UP LOCATION
Choose a location for the Media Connector that is convenient to the classroom audio
sources and power supply.
The Media Connector can be placed on a counter or wall mounted. Determine the best
location for your room. Use the guidelines below when selecting the site.
Set it up in a convenient place near a power source that is highly accessible for both
teachers and students. If plugging in multimedia audio sources, it should be located in
close proximity to minimize cable runs.
Key considerations:
Near multimedia audio sources if desired
Do not place in a fully enclosed metal cabinet
COUNTER OR DESKTOP
Locate 3-6 feet o of the floor to allow for best transmission.
WALL MOUNTING
Find a location on the wall that is near the computer or other AV equipment that will
be connected to the Media Connector.
Power for the Media Connector must be within 6  of this location.
1. Hold Media Connector up to the wall and ensure that it is level. Mark the mounting
holes with a pencil. The back of the Media Connector that contains the inputs may
be mounted in any position that is desirable.
2. For sheetrock walls, use screw-in sheetrock anchors and screws (not supplied) to
secure the Media Connector to the wall. It is best to drill a 1/4” pilot hole at the two
mounting locations before inserting the anchors.
3. Once the anchors are installed, place the Media Connector over the mounting
anchors and insert screws through the mounting holes and into the anchor.
4. If walls are concrete or cinder block, appropriate mounting hardware should be
purchased locally.
WALL MOUNTED
COUNTER OR DESK
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

Lightspeed Topcat Guide d'installation

Catégorie
Équipement musical supplémentaire
Taper
Guide d'installation

dans d''autres langues