E12
User Manual
WARNING
AVERTISSEMENT
ALWAYS FOLLOW SAFETY PRECAUTIONS
RESPECTEZ TOUJOURS LES CONSIGNES DE SÉCURITÉ
Death or serious injury may occur when children climb on audio and/or
video equipment furniture. A remote control or toys placed on the
furnishing may encourage a child to climb on the furnishing and as a
result the furnishing may tip over on to the child.
Relocating audio and/or video equipment to furniture not specifically
designed to support audio and/or video equipment may result in death or
serious injury due to the furnishing collapsing or over turning onto a child.
Il y a un danger de blessures graves ou même de mort si un enfant
grimpe sur un meuble pour matériels audio ou vidéo. Une télécommande
ou un jouet laissés sur le meuble peuvent inciter l'enfant à y grimper, ce
qui peut provoquer le basculement du meuble sur l'enfant.
Le repositionnement de matériels audio ou vidéo sur un meuble non
spécialement conçu pour cela peut causer la mort ou des blessures
graves par effondrement ou renversement du meuble sur un enfant.
Push
Secure the cabinet
to avoid fall down.
Sécurisez l’armoire pour
éviterqu’elle soit tombée.
Poussée
Only Adults should
move the cabinet.
L’armoire ne doit être
déplacé QUE PAR DES
ADULTES.
Never climb, sit or
stand on the cabinet.
Personne ne doit s'asseoi r,
se tenir ou grimper sur
armoire.
CAUTION
DO NOT allow anyone to sit, stand or climb on the station.
DO NOT lift the station.
DO NOT block the ventilation holes used for air circulation.
DO NOT overload objects on the station shelves. (shelf maximum loading =
38.1kg / 84lbs).
DO NOT put any devices that exceed the maximum loading weight on the
shelf of station.
DO NOT put any devices (e.g. TV, Monitor, Documents camera, etc.) on top
of the station.
DO NOT use any TV/monitor/display on top of the station.
Before moving the station, disconnect the power from the wall outlet.
When moving the station, make sure the power cord is firmly plugged into the
socket and confirm main earth connection.
When disconnecting the AC power cord, be absolutely sure to first disconnect
the plug from the outlet socket.
The socket-outlet shall be installed near the equipment and shall be easily
accessible.
ATTENTION !
PERSONNE ne doit s'asseoir, se tenir ou grimper sur armoire.
IL NE FAUT PAS soulever armoire.
IL NE FAUT PAS obstruer les orifices de ventilation qui permettent à l'air de
circuler.
IL NE FAUT PAS surcharger d'objets les étagères du armoire (charge
maximale de l'étagère : 38.1kg / 84lbs).
NE PAS placer d'appareils dont le poids dépasse la charge maximale sur
l'étagère de l’armoire.
IL NE FAUT poser aucun appareil (poste de TV, moniteur, caméra pour
documents, etc.) sur le haut dudit armoire.
N'utilisez aucun téléviseur ni moniteur sur le haut du armoire.
Avant de déplacer le armoire, débranchez la prise secteur.
Avant de démarrer le système, assurez-vous que le cordon d’alimentation est
branché adéquatement sur une prise de courant ainsi que la connexion
principale de mise à la terre soit établie.
Lors de la déconnexion du cordon d’alimentation, soyez absolument certains
que la fiche a été retirée de la prise de courant.
La prise secteur doit être installée près de l'appareil et être facilement
accessible.
Federal Communications Commission Statement
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radiofrequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct the interference at
his own expense.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate this equipment.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired
operation.
DISCLAIMER
No warranty or representation, either expressed or implied, is made with respect to the contents of this
documentation, its quality, performance, merchantability, or fitness for a particular purpose. Information
presented in this documentation has been carefully checked for reliability; however, no responsibility is
assumed for inaccuracies. The information contained in this documentation is subject to change without
notice.
In no event will AVer Information Inc. be liable for direct, indirect, special, incidental, or consequential damages
arising out of the use or inability to use this product or documentation, even if advised of the possibility of such
damages.
TRADEMARKS
“AVer” is a trademark owned by AVer Information Inc. Other trademarks used herein for description purpose
only belong to each of their companies.
COPYRIGHT
©2021 AVer Information Inc. All rights reserved.
All rights of this object belong to AVer Information Inc. Reproduced or transmitted in any form or by any means
without the prior written permission of AVer Information Inc. is prohibited. All information or specifications are
subject to change without prior notice.
The mark of Crossed-out wheeled bin indicates that this product must not be disposed of with your
other household waste. Instead, you need to dispose of the waste equipment by handing it over to a
designated collection point for the recycling of waste electrical and electronic equipment. For more
information about where to drop off your waste equipment for recycling, please contact your
household waste disposal service or the shop where you purchased the product.
Before running the system, make sure the power cord is firmly plugged into the socket and confirm main earth connection.
CAUTION
When disconnecting the AC power cord, be absolutely sure to first disconnect the plug from the outlet socket.
Contact Information
AVer Information Inc., Americas
https://www.averusa.com
668 Mission Ct., Fremont, CA 94539, USA
Tel: +1 (408) 263 3828
Toll-free: +1 (877) 528 7824
Technical support: support.usa@aver.com
CONTENTS
Contact Information ................................................................................................ 5
Package Contents ................................................................................................... 1
Tools Required ........................................................................................................ 2
Dimensions .............................................................................................................. 3
Diagram .................................................................................................................... 3
Front and Back ..................................................................................................... 3
Sides ..................................................................................................................... 4
Top and Bottom ..................................................................................................... 4
Installation ............................................................................................................... 5
Step 1: Install door lock cover (Optional) .............................................................. 6
Step 2: Connect the power strip to a wall outlet ................................................... 7
Step 3: Adapter configuration ............................................................................... 8
Step 4: Extend and fix the sides of the chassis .................................................... 9
Step 5: Insert dividers into the slots on the shelf ................................................ 10
Step 6: Cable management ................................................................................. 11
Step 7: Install top cover (Optional) ..................................................................... 12
Step 8: Secure the charging station (Optional) ................................................... 12
Desk mount (Optional) ......................................................................................... 13
Troubleshooting .................................................................................................... 14
Specifications ........................................................................................................ 15
Service and Warranty ........................................................................................... 16
Appendix – Earthing ............................................................................................. 17
1
Package Contents
The following items are included in the package. Please check if each item is
available before installing.
(folded)
Divider x 13
Top cover x 1
User Manual
Door lock cover x 1
(Unfolded)
E12 Station
Flat head screw x 11
(M4x5L)
Snap rivet x 8
Umbrella head screw x 4
(M4 x 5L)
Concrete anchor x 6
Lock key x 2
L- Shaped mounting
bracket x 2
Drywall anchor x 6
Washer x 6
Anchor screw x 6
2
Tools Required
See the assembly instructions for the tools you’ll need to use
Screwdriver
(For station use)
Drill
(For desk mount use)
3
Dimensions
Diagram
Front and Back
4
Sides
Top and Bottom
Front and Back Sides Top and Bottom
1. Top cover 6. Power cable hole 13. Ventilation holes
2. Finger pull 7. Ventilation holes
3. Door lock 8. Handle
4. Foot rubber 9. Fix Plate holes
5. Adapter cable holes 10. Snap Rivet holes
11. Ground
12. Antitheft Slot
5
Installation
Please check that you have taken out all package contents out and the numbers of
each item is correct before getting started.
Parts list
A Charging station
Chassis
Adapter drawer
Door lock cover
Top cover
Divider x 13
Snap rivet x 8
Flat head screw x 11
Umbrella head screw x 4
B Desk mount (optional)
L- Shaped bracket x 2
Concrete anchor x 6
Drywall anchor x 6
Anchor screw x 6
Washer x 6
6
Before installing the charging station
1. Be sure to reserve enough space for installation. It is recommended to reserve
at least 47.2”(W)* 35.42”(D) inches.
2. It is recommended to allocate 2 people for efficient assembly.
Step 1: Install door lock cover (Optional)
First, attach the door lock cover hole on the nut column, and then install the door
lock cover using 2 X umbrella head screws into the adapter drawer.
1
2
[Note]
It is recommended to use a long screwdriver to tighten screws.
X 2
7
Step 2: Connect the power strip to a wall outlet
1. Remove the packing material of the power strip.
2. Feed the power strip through the hole provided.
3. Connect the power strip to a wall outlet.
1 2
3
[Note]
Set the power socket to the OFF position before plugging the charging station to
wall outlet.
8
Step 3: Adapter configuration
1. Place the power adapter onto the adapter drawer in order.
2. Pass the DC-end of the adapter cable through the hole located on the back of
the adapter drawer.
3. Plug-in the AC-end of the adapter cable to the power AC socket.
4. Watch your hand when you place the chassis on the adapter drawer. Please
make sure the chassis is placed along the edge of the door lock.(The chassis
faces outwards, the door lock face inwards)
[Note]
Please place the power adapter onto the adapter drawer in order, don’t stack
the adapters.
For some device adapters that are not compatible with the power strip (EX:
e.g. iPad 8, iPad Air 4th generation), please contact AVer for help.
9
Step 4: Extend and fix the sides of the chassis
1. Extend the sides of the chassisout at right angles.
2. Insert 2 x flat head screws and 2 x snap rivets through the hole located on
the corners of the rear plate. Each corner has one on the top and one on the
bottom (4 screws / snap rivets total).
3. Fix the chassis on the adapter drawer with 3 x flat head screws.
[Note]
It is recommended to use a long screwdriver to tighten screws.
It is recommended to allocate 2 people for efficient assembly.
10
Step 5: Insert dividers into the slots on the shelf
Insert 13 x dividers into the slots on the shelf. Ensure that all dividers are properly
seated.
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
