PaloAlto Networks PA-220 Hardware Reference Manual

PA-220 Next-Gen Firewall Hardware

Reference

paloaltonetworks.com/documentation

2 PA-220 NEXT-GEN FIREWALL HARDWARE REFERENCE |

Contact Information

Corporate Headquarters:

Palo Alto Networks

3000 Tannery Way

Santa Clara, CA 95054

www.paloaltonetworks.com/company/contact-support

About the Documentation

• For the most recent version of this guide or for access to related documentation, visit the Technical

Documentation portal www.paloaltonetworks.com/documentation.

• To search for a specific topic, go to our search page www.paloaltonetworks.com/documentation/

document-search.html.

• Have feedback or questions for us? Leave a comment on any page in the portal, or write to us at

[email protected].

Copyright

Palo Alto Networks, Inc.

www.paloaltonetworks.com

©

2019-2019 Palo Alto Networks, Inc. Palo Alto Networks is a registered trademark of Palo

Alto Networks. A list of our trademarks can be found at www.paloaltonetworks.com/company/

trademarks.html. All other marks mentioned herein may be trademarks of their respective companies.

Last Revised

March 13, 2019

TABLE OF CONTENTS iii

Table of Contents

Before You Begin................................................................................................5

Tamper Proof Statement...........................................................................................................................7

Third-Party Component Support.............................................................................................................8

Product Safety Warnings.......................................................................................................................... 9

PA-220 Firewall Overview............................................................................. 13

PA-220 Front Panel................................................................................................................................. 15

PA-220 Back Panel...................................................................................................................................17

Install the PA-220 Firewall.............................................................................19

Install the PA-220 Firewall on a Flat Surface....................................................................................21

Install the PA-220 Firewall on a Wall..................................................................................................22

Install the PA-220 Firewall in a 19-inch Equipment Rack.............................................................. 24

Connect Power to a PA-220 Firewall..........................................................29

How to Connect Power to a PA-220 Firewall.................................................................................. 31

Service the PA-220 Firewall Hardware.......................................................33

Interpret the LEDs on a PA-220 Firewall........................................................................................... 35

Replace a Power Adapter on a PA-220 Firewall.............................................................................. 37

PA-220 Firewall Specifications......................................................................39

Physical Specifications............................................................................................................................. 41

Electrical Specifications........................................................................................................................... 42

Environmental Specifications................................................................................................................. 43

Miscellaneous Specifications..................................................................................................................44

PA-220 Firewall Compliance Statements Overview................................ 45

PA-220 Firewall Compliance Statements........................................................................................... 47

iv TABLE OF CONTENTS

5

Before You Begin

Read the following topics before you install or service a Palo Alto Networks

®

next-generation

firewall or appliance. The following topics apply to all Palo Alto Networks firewalls and

appliances except where noted.

> Tamper Proof Statement

> Third-Party Component Support

> Product Safety Warnings

6 PA-220 NEXT-GEN FIREWALL HARDWARE REFERENCE | Before You Begin

©

2019 Palo Alto Networks, Inc.

PA-220 NEXT-GEN FIREWALL HARDWARE REFERENCE | Before You Begin 7

©

2019 Palo Alto Networks, Inc.

Tamper Proof Statement

To ensure that products purchased from Palo Alto Networks were not tampered with during shipping, verify

the following upon receipt of each product:

• The tracking number provided to you electronically when ordering the product matches the tracking

number that is physically labeled on the box or crate.

• The integrity of the tamper-proof tape used to seal the box or crate is not compromised.

• The integrity of the warranty label on the firewall or appliance is not compromised.

(PA-7000 Series firewalls only) PA-7000 Series firewalls are modular systems and therefore

do not include a warranty label on the firewall.

8 PA-220 NEXT-GEN FIREWALL HARDWARE REFERENCE | Before You Begin

©

2019 Palo Alto Networks, Inc.

Third-Party Component Support

Before you consider installing third-party hardware, read the Palo Alto Networks Third-Party Component

Support statement.

PA-220 NEXT-GEN FIREWALL HARDWARE REFERENCE | Before You Begin 9

©

2019 Palo Alto Networks, Inc.

Product Safety Warnings

To avoid personal injury or death for yourself and others and to avoid damage to your Palo Alto Networks

hardware, be sure you understand and prepare for the following warnings before you install or service the

hardware. You will also see warning messages throughout the hardware reference where potential hazards

exist.

All Palo Alto Networks products with laser-based optical interfaces comply with 21 CFR

1040.10 and 1040.11.

The following safety warnings apply to all Palo Alto Networks firewalls and appliances, unless a specific

hardware model is specified.

• When installing or servicing a Palo Alto Networks firewall or appliance hardware component that has

exposed circuits, ensure that you wear an electrostatic discharge (ESD) strap. Before handling the

component, make sure the metal contact on the wrist strap is touching your skin and that the other end

of the strap is connected to earth ground.

French Translation: Lorsque vous installez ou que vous intervenez sur un composant matériel de

pare-feu ou de dispositif Palo Alto Networks qui présente des circuits exposés, veillez à porter un

bracelet antistatique. Avant de manipuler le composant, vérifiez que le contact métallique du bracelet

antistatique est en contact avec votre peau et que l’autre extrémité du bracelet est raccordée à la terre.

• Use grounded and shielded Ethernet cables to ensure agency compliance with electromagnetic

compliance (EMC) regulations.

French Translation: D es câbles Ethernet blindés reliés à la terre doivent être utilisés pour garantir la

conformité de l'organisme aux émissions électromagnétiques (CEM).

• (PA-220 firewalls only) The PA-220 firewall meets the requirements of IEC 61000-4-5 surge immunity

test. To prevent damage from electrical surges on Ethernet ports, we recommend that you use an

Ethernet surge protection device with the following specifications:

• Rated for Gigabit Ethernet up to category 5E and minimum 1Gbps.

• Protection provided on all eight signal leads.

• Both line-to-line and line-to-ground/shield are provided.

• Protection device must be connected to earth ground and use shielded category 5E or higher

Ethernet cable.

Technical Specifications:

• Protective circuit complies with IEC test classifications B2, C1, C2, C3, and D1.

• Normal discharge current (core to earth ground) is 2kA per signal pair.

• Normal discharge current (core to core) is 100A.

• Total discharge current is 10kA.

• French Translation: (PA-220 uniquement) Les pare-feux PA-220 sont conformes aux exigences du test

d’immunité aux surtensions IEC 61000-4-5. Pour éviter les dommages résultant de surtension électrique

sur les ports Ethernet, il est recommandé d’utiliser un dispositif de protection contre les surtensions aux

caractéristiques suivantes:

• Gigabit Ethernet jusqu’à la catégorie 5E, débit 1 Go/s minimum.

• Protection sur les huit câbles signal.

• Le blindage et la mise à la terre “ligne à ligne” et “ligne à la terre” sont fournis.

• Le dispositif de protection doit être raccordé à la terre et un câble Ethernet blindé de catégorie 5E ou

supérieure doit être utilisé.

Caractéristiques techniques:

10 PA-220 NEXT-GEN FIREWALL HARDWARE REFERENCE | Before You Begin

©

2019 Palo Alto Networks, Inc.

• Le circuit de protection est conforme aux classifications de test IEC B2, C1, C2, C3, et D1.

• Le courant de décharge normal (cœur vers terre) est de 2kA par paire de signal.

• Le courant de décharge normal (cœur vers cœur) est de 100 A.

• Le courant de décharge total est de 10kA.

• Do not connect a supply voltage that exceeds the input range of the firewall or appliance. For details

on the electrical range, refer to electrical specifications in the hardware reference for your firewall or

appliance.

French Translation: Veillez à ce que la tension d’alimentation ne dépasse pas la plage d’entrée du

pare-feu ou du dispositif. Pour plus d’informations sur la mesure électrique, consulter la rubrique des

caractéristiques électriques dans la documentation de votre matériel de pare-feu ou votre dispositif.

• Do not replace a battery with an incorrect battery type; doing so can cause the replacement battery to

explode. Dispose of used batteries according to local regulations.

French Translation: Ne remplacez pas la batterie par une batterie de type non adapté, cette dernière

risquerait d’exploser. Mettez au rebut les batteries usagées conformément aux instructions.

• (All firewalls with two or more power supplies) Disconnect all power cords (AC or DC) from the power

inputs to fully de-energize the hardware.

French Translation: (Tous les pare-feux avec au moins deux sources d’alimentation) Débranchez tous les

cordons d’alimentation (c.a. ou c.c.) des entrées d’alimentation et mettez le matériel hors tension.

• (PA-7000 Series firewalls only) When removing a fan tray from a PA-7000 Series firewall, first pull the

fan tray out about 1 inch (2.5cm) and then wait a minimum of 10 seconds before extracting the entire

fan tray. This allows the fans to stop spinning and helps you avoid serious injury when removing the

fan tray. You can replace a fan tray while the firewall is powered on but you must replace it within 45

seconds and you can only replace one fan tray at a time to prevent the thermal protection circuit from

shutting down the firewall.

French Translation: (Pare-feu PA-7000 uniquement) Lors du retrait d’un tiroir de ventilation d’un pare-

feu PA-7000, retirez tout d’abord le tiroir sur 2,5 cm, puis patientez au moins 10 secondes avant de

retirer complètement le tiroir de ventilation. Cela permet aux ventilateurs d’arrêter de tourner et permet

d’éviter des blessures graves lors du retrait du tiroir. Vous pouvez remplacer un tiroir de ventilation

lors de la mise sous tension du pare-feu. Toutefois, vous devez le faire dans les 45 secondes et vous ne

pouvez remplacer qu’un tiroir à la fois, sinon le circuit de protection thermique arrêtera le pare-feu.

• (All firewalls with two or more power supplies) Disconnect all power cords (AC or DC) from the power

inputs to fully de-energize the hardware.

French Translation: (Tous les pare-feux avec au moins deux sources d’alimentation) Débranchez tous les

cordons d’alimentation (c.a. ou c.c.) des entrées d’alimentation et mettez le matériel hors tension.

The following applies only to Palo Alto Networks firewalls that support a direct current (DC) power source:

French Translation: Les instructions suivantes s’appliquent uniquement aux pare-feux de Palo Alto

Networks prenant en charge une source d’alimentation en courant continu (c.c.):

• Do not connect or disconnect energized DC wires to the power supply.

French Translation: Ne raccordez ni débranchez de câbles c.c. sous tension à la source d’alimentation.

• The DC system must be earthed at a single (central) location.

French Translation: Le système c.c. doit être mis à la terre à un seul emplacement (central).

• The DC supply source must be located within the same premises as the firewall.

French Translation: La source d’alimentation c.c. doit se trouver dans les mêmes locaux que ce pare-feu.

• The DC battery return wiring on the firewall must be connected as an isolated DC (DC-I) return.

French Translation: Le câblage de retour de batterie c.c. sur le pare-feu doit être raccordé en tant que

retour c.c. isolé (CC-I).

PA-220 NEXT-GEN FIREWALL HARDWARE REFERENCE | Before You Begin 11

©

2019 Palo Alto Networks, Inc.

• The firewall must be connected either directly to the DC supply system earthing electrode conductor

or to a bonding jumper from an earthing terminal bar or bus to which the DC supply system earthing

electrode conductor is connected.

French Translation: Ce pare-feu doit être branché directement sur le conducteur à électrode de mise à

la terre du système d’alimentation c.c. ou sur le connecteur d'une barrette/d'un bus à bornes de mise à la

terre auquel le conducteur à électrode de mise à la terre du système d'alimentation c.c. est raccordé.

• The firewall must be in the same immediate area (such as adjacent cabinets) as any other equipment that

has a connection between the earthing conductor of the DC supply circuit and the earthing of the DC

system.

French Translation: Le pare-feu doit se trouver dans la même zone immédiate (des armoires adjacentes

par exemple) que tout autre équipement doté d’un raccordement entre le conducteur de mise à la terre

du même circuit d’alimentation c.c. et la mise à la terre du système c.c.

• Do not disconnect the firewall in the earthed circuit conductor between the DC source and the point of

connection of the earthing electrode conductor.

French Translation: Ne débranchez pas le pare-feu du conducteur du circuit de mise à la terre entre la

source d'alimentation c.c. et le point de raccordement du conducteur à électrode de mise à la terre.

• Install all firewalls that use DC power in restricted access areas only. A restricted access area is where

access is granted only to craft (service) personnel using a special tool, lock and key, or other means of

security, and that is controlled by the authority responsible for the location.

French Translation: Tous les pare-feux utilisant une alimentation c.c. sont conçus pour être installés

dans des zones à accès limité uniquement. Une zone à accès limité correspond à une zone dans laquelle

l’accès n’est autorisé au personnel (de service) qu'à l'aide d'un outil spécial, cadenas ou clé, ou autre

dispositif de sécurité, et qui est contrôlée par l'autorité responsable du site.

• Install the firewall DC ground cable only as described in the power connection procedure for the firewall

that you are installing. You must use the American wire gauge (AWG) cable specified and torque all nuts

to the torque value specified in the installation procedure for your firewall.

French Translation: Installez le câble de mise à la terre c.c. du pare-feu comme indiqué dans la procédure

de raccordement à l’alimentation pour le pare-feu que vous installez. Utilisez le câble American wire

gauge (AWG) indiqué et serrez les écrous au couple indiqué dans la procédure d’installation de votre

pare-feu pare-feu.

• The firewall permits the connection of the earthed conductor of the DC supply circuit to the earthing

conductor at the equipment as described in the installation procedure for your firewall.

French Translation: Ce pare-feu permet de raccorder le conducteur de mise à la terre du circuit

d’alimentation c.c. au conducteur de mise à la terre de l’équipement comme indiqué dans la procédure

d’installation du pare-feu.

• A suitably-rated DC mains disconnect device must be provided as part of the building installation.

French Translation: Un interrupteur d'isolement suffisant doit être fourni pendant l'installation du

bâtiment.

12 PA-220 NEXT-GEN FIREWALL HARDWARE REFERENCE | Before You Begin

13

PA-220 Firewall Overview

The Palo Alto Networks

®

PA-220 next-generation firewall is designed for small organizations

or branch offices and includes the following main features: active/passive and active/active

high availability (HA), passive cooling (no fans) to reduce noise and power consumption, eight

Ethernet ports, and dual power adapters for power redundancy. The PA-220 firewall enables

you to secure your organization through advanced visibility and control of applications, users,

and content.

First Supported Software Release: PAN-OS

®

8.0

The following topics describe the hardware features of the PA-220 firewall. To view or

compare performance and capacity information, refer to the Product Selection tool.

> PA-220 Front Panel

> PA-220 Back Panel

14 PA-220 NEXT-GEN FIREWALL HARDWARE REFERENCE | PA-220 Firewall Overview

©

2019 Palo Alto Networks, Inc.

PA-220 NEXT-GEN FIREWALL HARDWARE REFERENCE | PA-220 Firewall Overview 15

©

2019 Palo Alto Networks, Inc.

PA-220 Front Panel

The following image shows the front panel of the PA-220 firewall and the table describes each front panel

component.

Item Component Description

1 Ethernet ports Eight RJ-45 10/100/1000Mbps

ports for network traffic.

You can set the link speed and

duplex or choose auto-negotiate.

2 MGT port Use this Ethernet

10/100/1000Mbps port

to access the management

web interface and perform

administrative tasks. The

firewall also uses this port for

management services, such as

retrieving licenses and updating

threat and application signatures.

3 CONSOLE port

(RJ-45)

Use this port to connect a

management computer to the

firewall using a 9-pin serial

to RJ-45 cable and terminal

emulation software.

The console connection provides

access to firewall boot messages,

the Maintenance Recovery Tool

(MRT), and the command line

interface (CLI).

If your

management

computer does

not have a serial

port, use a

USB-to-serial

converter.

Use the following settings

to configure your terminal

emulation software to connect to

the console port:

16 PA-220 NEXT-GEN FIREWALL HARDWARE REFERENCE | PA-220 Firewall Overview

©

2019 Palo Alto Networks, Inc.

Item Component Description

• Data rate: 9600

• Data bits: 8

• Parity: none

• Stop bits: 1

• Flow control: None

4 CONSOLE port

(Micro USB)

Use this port to connect a

management computer to the

firewall using a standard Type-A

USB-to-micro USB cable.

The console connection provides

access to firewall boot messages,

the Maintenance Recovery Tool

(MRT), and the command line

interface (CLI).

Refer to Micro USB Console

Port for more information and to

download the Windows driver or

to learn how to connect from a

Mac or Linux computer.

5 USB port Use this port to bootstrap the

firewall.

Bootstrapping enables you to

provision the firewall with a

specific PAN-OS configuration

and then license it and make it

operational on your network.

6 LED status indicators Five LEDs that indicate the

status of the firewall hardware

components (see Interpret the

LEDs on a PA-220 Firewall).

PA-220 NEXT-GEN FIREWALL HARDWARE REFERENCE | PA-220 Firewall Overview 17

©

2019 Palo Alto Networks, Inc.

PA-220 Back Panel

The following image shows the back panel of the PA-220 firewall and the table describes each back panel

component.

Item Component Description

1 Power adapter inputs

(PWR 1 and PWR 2)

Use the power inputs to connect power to the

firewall.

Use only the PA-220 external

power adapters provided by Palo

Alto Networks.

2 Ground stud Use the single post ground stud to connect

the firewall to earth ground (ground cable not

included).

18 PA-220 NEXT-GEN FIREWALL HARDWARE REFERENCE | PA-220 Firewall Overview

19

Install the PA-220 Firewall

The PA-220 next-generation firewall ships with the hardware required to install the firewall on

a flat surface or on a wall. You can also order a rack mount kit to

> Install the PA-220 Firewall on a Flat Surface

> Install the PA-220 Firewall on a Wall

> Install the PA-220 Firewall in a 19-inch Equipment Rack

20 PA-220 NEXT-GEN FIREWALL HARDWARE REFERENCE | Install the PA-220 Firewall

©

2019 Palo Alto Networks, Inc.

La page charge ...

PaloAlto Networks PA-220 Hardware Reference Manual

PaloAlto Networks PA-220 Hardware Reference Manual

dans d''autres langues

Autres documents