Kobalt SGY-AIR185 Manuel utilisateur

Taper
Manuel utilisateur

Ce manuel convient également à

ATTACH YOUR RECEIPT HERE
Serial Number Purchase Date
Questions, problems, missing parts? Before returning to your
retailer, please call our Customer Service Department at
1-888-3KOBALT, 8 a.m. – 8 p.m., EST, Monday – Friday.
ITEM #0840781
MODEL #SGY-AIR185
1/2 IN. COMPACT
IMPACT WRENCH
Français p. 17
Español p. 34
kobalttools.com
AB1752
Kobalt
®
is a registered trademark of LF, LLC.
All rights reserved.
1
kobalttools.com
2
TABLE OF CONTENTS
Safety Information..........................................................................................3
Compressor Requirements.............................................................................2
Package Contents........................................................................................10
Product Specifications....................................................................................3
Preparation...................................................................................................10
Assembly Instructions...................................................................................11
Operating Instructions..................................................................................13
Care and Maintenance.................................................................................14
Troubleshooting............................................................................................15
Warranty.......................................................................................................16
COMPRESSOR REQUIREMENTS
5.3
SCFM
90
PSI
Tool Requirements
Exigences relatives aux outils
Requisitos de herramientas
@
IMPORTANT: To operate correctly, this tool requires airflow of at least
5.3 Standard Cubic Feet per Minute(SCFM) at 90 Pounds per Square
Inch (PSI).
Air hoses may cause loss in pressure up to 15 PSI, requiring a higher
compressor output to compensate and maintain required pressure at the tool.
Check the specifications of your air compressor to be sure it can support
both the SCFM and PSI required by this specific tool.
kobalttools.com
3
PRODUCT SPECIFICATIONS
SPECIFICATIONS
1/2 IN
10,000 RPM
450 FT-LB
5.3 SCFM
1/4 IN NPT
3/8 IN
90 PSI
COMPONENT
SQUARE DRIVE
SPEED
MAX. TORQUE
AVERAGE AIR CONSUMPTION
AIR INLET
RECOMMEND AIR HOSE
WORKING PRESSURE
SAFETY INFORMATION
Please read and understand this entire manual before attempting to
assemble, operate or maintain this product. If you have any questions,
please call our Customer Service Department at 1-888-3KOBALT,
8 a.m. – 8 p.m., EST, Monday – Friday.
WARNING
WARNING
Improper operation or maintenance of this tool could result in serious injury
and property damage. Read and understand all warnings and operation
instructions before using this tool. When using any tool, basic safety
precautions should always be followed to reduce the risk of personal injury.
Use each tool for its intended function only. Do not use this product in
unsafe work conditions. It is always recommended to keep a fire
extinguisher and first aid kit near work areas.
FAILURE TO OBSERVE AND FOLLOW SAFETY INSTRUCTIONS COULD
RESU IN INJURY OR DEATH.
Some dust created by paint spraying, power sanding, sawing, grinding,
drilling and other related activities is known to the State of California to
cause cancer, birth defects and other reproductive harm. A listing of
chemicals can be obtained from www.oehha.ca.gov under proposition 65.
Some examples of these chemicals are:
Lead from lead based paints
Crystalline silica from bricks, cement and other masonry products
Arsenic and chromium from chemically treated lumber
Your risk from these exposures varies, depending on how often you do this
type of work. To reduce your exposure to these chemicals, work in a well
ventilated area and wear appropriate/approved safety equipment such as
respirators or dust masks which are specially designed to filter microscopic
particles.
kobalttools.com
4
SAFETY INFORMATION
RISK OF EYE OR HEAD INJURY
WARNING
WARNING
WARNING
WHAT COULD HAPPEN HOW TO PREVENT IT
WHAT COULD HAPPEN HOW TO PREVENT IT
WHAT COULD HAPPEN HOW TO PREVENT IT
This air-powered tool is capable of
propelling materials such as
fasteners, metal chips and other
debris at high speed, which could
result in serious injury.
Always wear ANSI-approved Z87.1
safety glasses with side shields.
Never leave a pressurized tool
unattended.
Disconnect tool from air supply when
tool is not in use or when changing
accessories to prevent accidental
operation.
Compressed air can be hazardous,
propelling objects or particles that
can cause injury into soft tissues
such as eyes and ears.
Never direct air at yourself or
anyone else.
For additional protection, use an
approved face shield in addition to
safety glasses.
Tool attachments can become loose
or break and fly apart, becoming
projectiles or propelling other objects
at the operator or bystanders in the
work area.
Make sure all attachments are
properly assembled and securely
fastened before use.
Always use the tool at a safe
distance from others in the work area.
Maintain awareness of work area
safety at all times.
RISK OF LOSS OF HEARING
RISK OF FIRE OR EXPLOSION
Always wear ANSI S3.19 hearing
protection.
Exposure to noise produced by air
tools can lead to permanent hearing
loss.
This tool is capable of generating
sparks which can result in ignition of
flammable materials.
Work in a clean, well ventilated area
free of combustible materials.
Never operate tools near flammable
substances such as gasoline,
naphtha, cleaning solvents, etc.
This tool is not recommended for
use in explosive atmospheres or
underwater.
kobalttools.com
5
SAFETY INFORMATION
RISK OF FIRE OR EXPLOSIN
WARNING
WARNING
WARNING
WHAT COULD HAPPEN HOW TO PREVENT IT
WHAT COULD HAPPEN HOW TO PREVENT IT
WHAT COULD HAPPEN HOW TO PREVENT IT
RISK OF ENTANGLEMENT
RISK OF CUTS OR BURNS
This tool is capable of generating
sparks, which can result in ignition of
flammable materials.
Never use oxygen, carbon dioxide or
other bottled gasses as a power
source for air tools. Use only clean,
dry air at the specified pressure.
Wiping or cleaning rags and other
flammable waste materials that may
have been used on the tool must be
placed in a tightly closed metal
container, and disposed of in a
proper manner.
Air tools that contain moving
elements or drive other moving parts
(such as impact sockets) can
become entangled in hair, clothing,
jewelry and other loose objects,
resulting in severe injury.
Do not wear loose clothing, jewelry
or anything that may get caught or
tangled in the tool, hose or workpiece.
Always keep hands and body parts
away from moving parts.
Always wear properly fitted clothing
and other properly fitted safety
equipment when using tools.
Whipping hoses can cause serious
injury. Always check for damaged or
loose hose fittings before using tools.
Air tools are capable of causing
serious injury if operated improperly
or in a manner for which the tool is
not intended. Accessories can
become extremely hot through
friction where they contact the
workpiece.
Wear gloves when using tools.
Keep the working part of the tool
away from hands and body.
Do not touch accessories with bare
hands during or immediately after
use.
kobalttools.com
6
SAFETY INFORMATION
RISK OF ELECTRIC SHOCK
WARNING
WARNING
WHAT COULD HAPPEN HOW TO PREVENT IT
WHAT COULD HAPPEN HOW TO PREVENT IT
RISK OF PERSONAL INJURY
This tool is NOT electrically insulated.
Contact with a “live” wire will also
make exposed metal parts of the tool
“live” and can result in electrical
shock, electrocution injury or death.
Never use air tools where they may
come in contact with energized
electrical wiring.
Avoid body contact with grounded
surfaces such as pipes, radiators,
refrigerators and ranges. There is
an increased risk of electrical shock
if your body is grounded.
Whenever possible, it is
recommended that electrically
non-conductive clothing and non-skid
footwear be worn when using tools.
Air tool accessories such as impact
sockets or drills that come into
contact with hidden electrical wiring
could cause electrocution or death.
Thoroughly investigate workpieces
and work areas for possible hidden
wiring before performing work.
An unattended tool could be
activated by unauthorized/untrained
persons, leading to their injury or
injury to others.
Remove air hose when the tool is
not in use and store tool in a secure
location away from reach of children
and untrained users.
Air tools can propel fasteners,
loose/broken accessories or other
objects throughout the work area.
Never run the tool off the workpiece.
Maintain awareness of work area
safety at all times. Always be aware
of other people around the work area
to ensure safety.
Use only parts, fasteners and
accessories recommended by the
manufacturer.
Keep work area clean, free of clutter
and well lit. Do not allow children to
operate any tool, and keep children
away from work areas.
kobalttools.com
7
SAFETY INFORMATION
WARNING
WHAT COULD HAPPEN HOW TO PREVENT IT
RISK OF PERSONAL INJURY
Sockets that are left attached to a
rotating part of the tool may fly off
and increase the risk of personal
injury.
Air tools can become activated by
accident while being handled or
during tool changes, maintenance
or repair.
Always remove and secure the
socket after use.
Disconnect the tool from the air
supply during tool changes,
maintenance or repair.
Never carry the tool by the air hose.
Always carry the tool by the handle.
Avoid unintentional operation.
Never carry the tool with the trigger
depressed or engaged. Do not lock,
tape or wire the trigger for
continuous operation.
Only an authorized service
representative should do repair
servicing.
Air tools can cause the workpiece to
move upon contact, leading to injury.
Always make sure the workpiece is
secure. Use clamps or other devices
to prevent movement.
Loss of control of the tool can lead to
operator injury or injury to others in
the work area.
Always shut off the air supply and
release/drain air pressure from the
hose before changing accessories or
making repairs. When tool is not in
use, disconnect it from the air supply
and store the tool in a safe location.
Never operate tools while using
drugs or alcohol.
Do not overreach or stretch to
operate the tool.
kobalttools.com
8
SAFETY INFORMATION
WARNING
WHAT COULD HAPPEN HOW TO PREVENT IT
RISK OF PERSONAL INJURY
There is a risk of bursting if the tool
is damaged.
Loss of control of the tool can lead to
operator injury or injury to others in
the work area.
Keep proper footing at all times
when handling tools. Slipping,
tripping and/or falling are major
causes of serious injury and or death.
Keep tool handles dry, clean and
free from oil/grease.
Be aware of excess air hose,
electrical power sources and other
obstacles or hazards in the work area.
Stay alert. Watch what you are doing.
Use common sense. Do not operate
tools when you are tired.
Operators must be able to easily
handle the entire weight of the tool in
operation, to maintain full control of
the tool 100% of the time.
Check for misalignment or binding of
moving parts, broken parts and other
conditions that affect safe tool
operation.
Poor quality, improper or damaged
attachments can detach or fly apart
during operation, sending projectiles
through the work area and causing
serious injury.
Never use a tool that has been
dropped, damaged or appears to
malfunction. Never use tools that
are leaking air or have missing parts.
Remove damaged or malfunctioning
tools from the workplace immediately.
Do not use pressure exceeding the
recommended operating pressure of
any of the parts (hoses, fittings, etc.)
in the system.
Use only impact-grade sockets with
air impact tools. Always use
attachments rated for the speed of
the tool. Do not modify tools or
attachments.
Do not apply excessive force to the
tool; let the tool perform the work.
Follow lubrication instructions for
best and safest operation.
kobalttools.com
9
SAFETY INFORMATION
WARNING
WHAT COULD HAPPEN HOW TO PREVENT IT
WHAT COULD HAPPEN HOW TO PREVENT IT
RISK OF PERSONAL INJURY
WARNING
INHALATION HAZARD
Poor quality, improper or damaged
attachments can detach or fly apart
during operation, sending projectiles
through the work area and causing
serious injury.
Always follow assembly, operation,
maintenance and repair instructions.
Improperly maintained tools and
accessories can cause serious
injury.
Maintain the tool and accessories
with care. Do not abuse hoses or
connectors.
Keep hoses away from heat, oil and
sharp edges. Always check air hoses
for weak or worn connections before
each use and make certain that all
connections are secure.
Keep tools clean and properly oiled
for best and safest performance.
Using an accessory not intended for
a specific tool increases the risk of
injury to the operator and everyone
else in the work area.
Always use accessories and
attachments designed for the tool
and the work at hand.
Do not improvise or modify tools or
accessories.
Repetitive motions, awkward
positions and exposure to vibration
can be harmful to hands and arms.
Discontinue use of tool if discomfort,
tingling feeling or pain occurs.
Consult a physician before resuming
use if any of these symptoms occur.
Abrasive tools such as grinders,
sanders and cut-off tools generate
dust and abrasive materials, which
can be harmful to the lungs and
respiratory system. Paint spraying
tools generate paint vapors, which
can be harmful to the lungs and
respiratory system.
Always wear a properly fitting
facemask or respirator rated for the
application when using such tools.
Some materials such as adhesives
and tar give off vapors, which could
cause serious injury with prolonged
exposure.
Always work in a clean, dry,
well-ventilated area. Be aware of
chemicals in the work area and read
all Materials Safety Data Sheets
(MSDS) for the materials and/or
chemicals that may be present.
kobalttools.com
10
PACKAGE CONTENTS
PREPARATION
DESCRIPTION
Wrench
Anvil (preassembled to Wrench (A))
Trigger (preassembled to Wrench (A))
Switch (preassembled to Wrench (A))
Air Inlet (preassembled to Wrench (A))
QUANTITY
1
1
1
1
1
PART
A
B
C
D
E
1/4 in. male plug
1
F
E
F
A
D
B
C
Before assembling this tool, make sure all parts are present. Compare parts
with package contents list. If any part is missing or damaged, do not attempt
to assemble the tool.
Estimated Assembly Time: 1 – 3 minutes
Tools and Materials Required for Assembly (not included):
• Adjustable wrench or 9/16-in. wrench
• Thread sealant tape
• Air tool oil (NOTE: Air tool oil is NOT compressor oil. Use of compressor oil
in this tool can damage the tool and/or shorten tool life. Use only air tool oil
in this tool).
kobalttools.com
11
ASSEMBLY INSTRUCTIONS
1. Remove plastic air inlet protective cap
from air inlet (E).
1
2
3
NOTE
2. Prepare a 1/4-in. male plug by applying
sealant tape (not included) to the
threading, wrapping clockwise. Screw
threaded male air plug by hand into air
inlet (E), then tighten with a wrench
(not included) for an airtight connection.
DO NOT OVERTIGHTEN.
Sealant tape must be used on this
connection.
3. Select the correct impact socket
(not included) for the threaded fastener to
be tightened or loosened and mount it onto
the anvil (B) until it clicks into place.
B
Use only adapters and sockets with a torque
rating equal to or greater than the tool itself.
Always make sure adapters and sockets are
properly mounted and secure before using
the tool. Loose attachments can break or fly
off, causing serious injury to the operator or
bystanders in the work area. Always follow
all manufacturers’ specifications for proper
attachment and use.
WARNING
kobalttools.com
12
ASSEMBLY INSTRUCTIONS
4
5
6
B
4. If necessary for a longer reach, mount an
extension bar (not included) onto the
anvil (B) until it clicks into place, then
mount the socket on the adapter.
NOTE
5. Place 2 – 3 drops of air tool oil
(not included) into the male air plug before
each use, as shown in Fig. 5.
Proper lubrication is EXTREMELY
important to assure proper tool performance
and avoid tool damage. ALWAYS lubricate
the tool before each use if not using an
in-line oiler.
6. Connect the air supply hose (not included)
to the male air plug, making sure it is
completely seated and secure. Set the
working pressure at 90 PSI for best tool
performance.
NOTE
To operate correctly, this tool requires
airflow of at least 5.3 cubic feet per minute
(SCFM) at 90 pounds per square inch (PSI)
at the tool.
kobalttools.com
13
OPERATING INSTRUCTIONS
D
1.This tool features a switch (D) that has
two functions:
Control the direction of spin: Forward (“F”)
to tighten or Reverse (“R”) to loosen the
fastener.
Set the amount of torque applied to the
fastener in the Forward (“F”) position:
Settings Low, Middle or High.
The Forward (“F”) settings Low, Middle and
High provide reference torque as shown
below. Choose the correct torque setting to
mount fasteners properly on the workpiece
as shown in Fig 1.
LOW
Middle
High
150 - 250 ft-lb
250 - 350 ft-lb
350 - 450 ft-lb
The Reverse (“R”) setting ALWAYS operates
at maximum power, as shown below:
R
≥450 ft-lb
Maximum power to
remove fastener from
workpiece.
Setting
Suggested Use
Torque in
Forward (“F”)
Least power to mount
fastener on workpiece
Medium power to
tighten fastener
Highest power to
tighten fastener
NOTE
Impact wrenches are NOT torque
wrenches.
Fasteners requiring a specific
torque must be checked with an appropriate
torque wrench after the fastener has been
tightened.
2.To install and tighten a threaded
fastener (not included), turn the switch (D)
to the right, until it clicks into place for the
desired setting.
Place the
socket (not included) over the threaded
fastener on the workpiece, apply
pressure and press the trigger (C).
The anvil (B) will spin clockwise to tighten
the threaded fastener down.
D
C
B
2
1
kobalttools.com
14
OPERATING INSTRUCTIONS
CARE AND MAINTENANCE
3
3.To loosen or remove a threaded fastener,
turn the
switch (D) to the left until it clicks
into place.
Place the socket over the
threaded fastener on the workpiece,
apply pressure and press trigger (C).
The anvil (B) will spin counterclockwise to
loosen the threaded fastener up.
D
C
B
WARNING:
Always make sure the
workpiece is secure. Never run the tool off
the workpiece. Do not apply excessive
force to the tool; let the tool perform the
work.
ALWAYS DISCONNECT TOOL FROM THE AIR SUPPLY BEFORE
PERFORMING ANY MAINTENANCE ON THE TOOL.
Always make sure the tool is properly lubricated during operation. Proper
lubrication is shown in this instruction manual.
An in-line oiler (not included) is recommended to help increase tool life and
keep the tool properly lubricated. The in-line oiler should be regularly
checked and filled with air tool oil as needed. Proper adjustment of the in-line
oiler can be performed by placing a sheet of paper next to the tool’s exhaust
ports while holding the throttle completely open for 30 seconds. When a light
stain of oil collects on the paper, the oiler is properly adjusted. Excessive
amounts of oil should be avoided.
Clean the entire tool with a cotton rag after each use. If storing the tool for an
extended period, it should be lubricated and run for approximately 30
seconds to ensure oil has been evenly distributed throughout the tool. Always
store tools in a clean, dry environment away from the reach of children.
Recommended lubricants: air-tool oil or any other high-grade turbine oil
containing moisture absorbent, rust inhibitors, metal wetting agents and an
EP (Extreme Pressure) additive. Consult your local retailer for further
assistance in selecting air tool oil best suited for proper lubrication.
STORAGE:
Tool must be well cleaned and lightly lubricated before storing.
Store tool in a dry, safe place out of the reach of children.
kobalttools.com
15
TROUBLESHOOTING
If the tool runs slowly or will not operate, check these possible problems and
take the required corrective action:
POSSIBLE PROBLEM SOLUTION
Grit or gum in tool.
No oil in tool.
Low air pressure.
Flush the tool with air-tool oil or gum solvent.
Lubricate the tool.
Adjust the regulator on the tool to the
maximum setting.
Adjust the compressor regulator to tool
maximum of 90 PSI.
NOTE: Air hoses may cause up to 15 PSI
loss in pressure, so you may need to set a
higher compressor output to maintain the
required pressure at the tool.
Tighten and seal hose fittings with sealing
tape if leaks are found.
Air hose leaks.
Pressure drops.
Be sure the hose is the proper size. Long
hoses or tools using large volumes of air may
require an internal diameter of 1/2 in. I.D. or
larger, depending on total hose length.
Do not use multiple hoses connected together
with quick-connect fittings. This causes
additional loss of pressure and reduces the
tool power. Use single hoses of the proper
length.
Replace rotor blade.Worn rotor blade.
Moisture blowing out of tool
exhaust.
Water in compressor tank; drain tank.
(See air compressor manual.) Oil the tool and
run until no water is evident. Oil the tool again
and run 1 – 2 seconds.
kobalttools.com
16
WARRANTY
This tool is warranted by the manufacturer to the original purchaser from the
original purchase date for three (3) years subject to the warranty coverage
described herein. This tool is warranted to the original user to be free from
defect in material and workmanship. If you believe that a tool is defective,
return the tool, with proper proof of purchase to the point of purchase. If it is
determined that the tool is defective and covered by this warranty, the
distributor will replace the tool or refund the purchase price.
This warranty is void if: defects in materials or workmanship or damages
result from repairs or alterations which have been made or attempted by
others or the unauthorized use of nonconforming parts; the damage is due to
normal wear, damage is due to abuse (including overloading of the tool
beyond capacity), improper maintenance, neglect or accident; or the damage
is due to the use of the tool after partial failure or use with improper
accessories or unauthorized repair or alteration.
This warranty gives you specific legal rights, and you may also have other
rights that vary from state to state. For warranty questions, call our Customer
Service Department at 1-888-3KOBALT, 8:00 a.m. – 8:00 p.m., EST,
Monday – Friday.
Printed in China
Kobalt
®
is a registered trademark of LF, LLC.
All rights reserved.
JOIGNEZ VOTRE REÇU ICI
Numéro de série Date d'achat
Des questions, des problèmes, des pièces manquantes? Avant
de retourner l'article au détaillant, communiquez avec notre service
à la clientèle au 1 888 3KOBALT, entre 8 h et 20 h (HNE), du lundi
au vendredi.
ARTICLE #0840781
MODÈLE #SGY-AIR185
1,27 CM CLÉ À
CHOCS COMPACTE
kobalttools.com
17
Kobalt est une marque de commerce
déposée de LF, LLC. Tous droits réservés.
®
kobalttools.com
18
TABLE DES MATIÈRES
Consignes de sécurité..................................................................................19
Exigences relatives au compresseur............................................................18
Contenu de l’emballage................................................................................27
Caractéristiques du produit...........................................................................19
Préparation...................................................................................................27
Instructions pour l’assemblage.....................................................................28
Mode d’emploi..............................................................................................30
Entretien.......................................................................................................31
Dépannage...................................................................................................32
Garantie........................................................................................................33
EXIGENCES RELATIVES AU COMPRESSEUR
5.3
SCFM
90
PSI
Tool Requirements
Exigences relatives aux outils
Requisitos de herramientas
@
IMPORTANT : Cet outil nécessite un débit d'air d'au moins 5.3 pi
3
par minute
à une pression de 90 lb/psi
2
.
L’utilisation d’un tuyau à air peut entraîner une chute de pression allant
jusqu’à 15 lb/po
2
. Il faut donc augmenter la pression venant du compresseur
afin de compenser cette chute et de maintenir un niveau adéquat à l’outil.
Vérifiez les spécifications de votre compresseur d’air afin de vous assurer
qu’il satisfait aux exigences (pi
3
/min et lb/po
2
) de l’outil.
kobalttools.com
19
CARACTÉRISTIQUES DU PRODUIT
CARACTÉRISTIQUES
12,7 mm
10 000 tours/minute
62,21 kgf/m
0,15 m
3
/mi
1/4 po NPT
3/8 po
90 lb /po
2
COMPOSANTE
LARGEUR DE L' EMBOUT CARRÉ
VITESSE
COUPLE MAXIMAL
CONSOMMATION D'AIR MOYENNE
ENTRÉE D'AIR
TUYAU À AIR RECOMMANDÉ
PRESSI ON DE SERVICE
CONSIGNES DE SÉCURITÉ
Veuillez vous assurer de lire et de comprendre l’intégralité du présent guide
avant d’assembler, faire fonctionner ou entretenir cet article. Si vous avez
des questions, veuillez téléphoner au service à la clientèle au
1 888 3KOBALT, entre 8 h et 20 h (HNE), du lundi au vendredi.
AVERTISSEMENT
AVERTISSEMENT
Une utilisation ou un entretien inadéquat de ce produit peut causer des
blessures graves ou des dommages matériels. Assurez-vous de lire et de
comprendre tous les avertissements et toutes les instructions concernant ce
produit avant de l’utiliser. Lorsque vous utilisez un outil pneumatique,
observez toujours les mesures de sécurité de base afin de réduire les risques
de blessure. Utilisez uniquement un outil, quel qu’il soit, pour l’usage auquel il
est destiné. N’utilisez pas cet article dans des conditions de travail
dangereuses. Il est toujours recommandé d’avoir un extincteur d’incendie et
une trousse de premiers soins à proximité des aires de travail.
LE NON-RESPECT DES CONSIGNES DE SÉCURITÉ PEUT ENTRAÎNER
DE GRAVES BLESSURES OU LAMORT.
La poussière créée pendant la pulvérisation de peinture, le ponçage, le sciage, le
polissage, le perçage et d’autres activités est reconnue par l’État de la Californie
comme étant la cause de cancers, d’anomalies congénitales et d’autres
problèmes liés aux fonctions reproductrices. Vous pouvez obtenir la liste de ces
produits chimiques au www.oehha.ca.gov conformément à la proposition 65.Voici
des exemples de ces produits chimiques :
le plomb contenu dans la peinture au plomb;
la silice cristalline provenant de la brique, du ciment ou d’autres matériaux de
maçonnerie;
l’arsenic et le chrome provenant du bois d’oeuvre traité avec un produit chimique.
Les risques liés à l’exposition à ces produits varient en fonction de la fréquence à
laquelle vous effectuez ce type de travaux. Afin de limiter votre exposition à ces
produits chimiques, travaillez dans un endroit bien ventilé et utilisez de
l’équipement de sécurité approuvé, tel qu’un appareil respiratoire ou un masque
antipoussière conçus spécialement pour filtrer les particules microscopiques.
kobalttools.com
20
CONSIGNES DE SÉCURITÉ
RISQUES DE BLESSURE AUX YEUX OU À LA TÊTE
AVERTISSEMENT
RISQUE
MESURES PRÉVENTIVES
RISQUE
MESURES PRÉVENTIVES
Cet outil pneumatique peut projeter
des fixations, des fragments de
métal et d’autres débris, ce qui peut
causer des blessures graves.
Portez toujours des lunettes de
sécurité conformes à la norme
ANSI Z87.1 et pourvues d’écrans
latéraux.
Ne laissez jamais un outil sous
pression sans surveillance.
Débranchez l’outil de l’alimentation
en air lorsque vous ne l’utilisez pas
ou lorsque vous changez
d’accessoire, afin d’éviter qu’il se
déclenche accidentellement.
RISQUE DE PERTE AUDITIVE
Portez toujours des protecteurs
auditifs conformes à la norme
ANSI S3.19.
L’air comprimé peut être dangereux,
car il est susceptible de projeter des
objets ou des particules pouvant
causer des blessures aux tissus
mous du corps, notamment les yeux
et les oreilles.
Ne pointez jamais le jet d’air vers
vous-même ou une autre personne.
Pour plus de protection, utilisez un
écran facial approuvé et portez des
lunettes de sécurité.
Les accessoires de l’outil peuvent se
desserrer ou se briser et se détacher.
Ils peuvent ainsi se transformer en
projectiles ou percuter d’autres objets
et les projeter vers l’utilisateur ou
d’autres personnes se trouvant dans
la zone de travail.
Assurez-vous que tous les
accessoires sont bien assemblés et
correctement fixés avant d’utiliser
l’article.
Utilisez toujours l’outil à une distance
sécuritaire des autres personnes
présentes dans l’aire de travail.
Assurez-vous que les mesures de
sécurité dans l’aire de travail sont
connues en tout temps.
L’exposition au bruit produit par les
outils pneumatiques peut entraîner
une perte auditive permanente.
AVERTISSEMENT
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50

Kobalt SGY-AIR185 Manuel utilisateur

Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues