Crestron HZ2-DIMUEX Information produit

Taper
Information produit

Ce manuel convient également à

HZ2-DIMUEX, -DIMLVEX, -DIMEX, -SWEX, -KPEX, and -AUX
Horizon® 2 In-Wall Dimmers, Switches, and Keypads with infiNET EX® Wireless and Multiway Remotes
PI - 9248B
(2059438)
04.23
Getting Started
Scan the QR code for product documentation.
The original language version of this document is
U.S. English.
All other languages are a translation of the original
document.
Certification and Compliance
Regulatory Model: M201849006, M201849001,
M201849002, M201849004, M201849005,
M201849003
Federal Communications Commission (FCC)
Compliance Statement
This device complies with part 15 of the FCC Rules.
Operation is subject to the following conditions:
(1) This device may not cause harmful interference
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
CAUTION: Changes or modifications not expressly
approved by the manufacturer responsible for
compliance could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if
not installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try
to correct the interference by one or more of the
following measures:
lReorient or relocate the receiving antenna.
lIncrease the separation between the equipment
and receiver.
lConnect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
lConsult the dealer or an experienced radio/TV
technician for help.
To satisfy FCC RF Exposure requirements for
mobile and base station transmission devices, a
separation distance of 20 cm or more should be
maintained between the antenna of this device and
persons during operation. To ensure compliance,
operation at closer than this distance is not
recommended. The antenna(s) used for this
transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Crestron Electronics, Inc.
15 Volvo Drive, Rockleigh, NJ 07647
Tel: 888.CRESTRON
Fax: 201.767.7656
www.crestron.com
Product Information - Doc. 9248B
(2059438)
04/13/23
Industry Canada (IC) Compliance Statement
CAN ICES-3 (B)/NMB-3(B)
This device contains licence-exempt transmitter
(s)/receiver(s) that comply with Innovation, Science
and Economic Development Canada’s licence-
exempt RSS(s). Operation is subject to the
following two conditions:
1. This device may not cause interference.
2. This device must accept any interference,
including interference that may cause undesired
operation of the device.
L’émetteur/récepteur exempt de licence contenu
dans le présent appareil est conforme aux CNR
d’Innovation, Sciences et Développement
économique Canada applicables aux appareils radio
exempts de licence.
L’exploitation est autorisée aux deux conditions
suivantes :
1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le
fonctionnement.
Under Industry Canada regulations, this radio
transmitter may only operate using an antenna of a
type and maximum (or lesser) gain approved for
the transmitter by Industry Canada. To reduce
potential radio interference to other users, the
antenna type and its gain should be so chosen that
the equivalent isotropically radiated power (e.i.r.p.)
is not more than that necessary for successful
communication.
Conformément à la réglementation d'Industrie
Canada, le présent émetteur radio peut fonctionner
avec une antenne d'un type et d'un gain maximal
(ou inférieur) approuvé pour l'émetteur par
Industrie Canada. Dans le but de réduire les risques
de brouillage radioélectrique à l'intention des
autres utilisateurs, il faut choisir le type d'antenne
et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas
l'intensité nécessaire à l'établissement d'une
communication satisfaisante.
This product is listed to applicable UL® Standards
and requirements tested by Intertek® services.
Ce produit est homologué selon les normes et les
exigences UL applicables par Intertek Prestations
de service.
Legal
The product warranty can be found at
www.crestron.com/warranty.
The specific patents that cover Crestron products
are listed online at patents.crestron.com.
Certain Crestron products contain open source
software. For specific information, please visit
www.crestron.com/opensource.
Crestron, the Crestron logo, Horizon, and infiNET
EX are either trademarks or registered trademarks
of Crestron Electronics, Inc. in the United States
and/or other countries. Intertek is either a
trademark or registered trademark of Intertek
Group in the United States and/or other countries.
The ETL logo is either a trademark or a registered
trademark of Intertek Testing Services NA in the
United States and/or other countries. UL is either a
trademark or a registered trademark of
Underwriters Laboratories, Inc. in the United States
and/or other countries. Other trademarks,
registered trademarks, and trade names may be
used in this document to refer to either the entities
claiming the marks and names or their products.
Crestron disclaims any proprietary interest in the
marks and names of others. Crestron is not
responsible for errors in typography or
photography.
©2023 Crestron Electronics, Inc.
  • Page 1 1
  • Page 2 2

Crestron HZ2-DIMUEX Information produit

Taper
Information produit
Ce manuel convient également à