Universal Electronics COGECO ATLAS DVR 5-DEVICE Manuel utilisateur

COGECO ATLAS DVR 5-DEVICE

Universal Remote Control

Télécommande universelle

ATLAS ENP 5 APPAREILS

de COGECO

User’s Guide

Guide d’utilisation

Atlas DVR M1055F1 9/3/04 7:30AM Page 1

TABLE OF CONTENTS

Introduction

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Features And Functions

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Key Charts

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Device Table

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Installing Batteries

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Programming Device Control

. . . . . . . . . . . . . . . . . . . . . . . 10

Programming TV/VCR Combo Control

. . . . . . . . . . . . . . . 12

Searching For Your Code

. . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Checking The Codes

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Programming Channel Control Lock

. . . . . . . . . . . . . . . . . 15

To Activate Channel Control Lock

. . . . . . . . . . . . . . . . . . . . . . 15

To De-Activate Channel Control Lock

. . . . . . . . . . . . . . . . . . . 15

Programming The F1 Key For Specific Channels

. . . . . . 16

To Program The F1 Key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

To Clear The F1 Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Using The Master Power Key

. . . . . . . . . . . . . . . . . . . . . . . . 18

To Program The Master Power Key . . . . . . . . . . . . . . . . . . . . . . . 18

To Operate The Master Power Key . . . . . . . . . . . . . . . . . . . . . . . 18

To Clear The Master Power Key . . . . . . . . . . . . . . . . . . . . . . . . . 19

Re-Assigning Device Keys

. . . . . . . . . . . . . . . . . . . . . . . . . 19

Changing Volume Lock

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Locking Volume Control To A Specific Device

(Individual Volume Unlock) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

To Unlock Volume Control To One Mode

(Global Volume Lock) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

To Unlock All Volume Control

(Global Volume Unlock) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Troubleshooting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Instructions To The User

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Additional Information

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Guide d’utilisation

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Manufacturer’s Codes

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Setup Codes For Audio Amplifiers . . . . . . . . . . . . . . . . . . . . . . . 46

Setup Codes For Audio Receivers . . . . . . . . . . . . . . . . . . . . . . . 47

Setup Codes For Cable Boxes (Converters) . . . . . . . . . . . . . . . . 49

Setup Codes For DVD Players. . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Setup Codes For PVRs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Setup Codes For Satellite Receivers . . . . . . . . . . . . . . . . . . . . . 53

Setup Codes For TVs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Setup Codes For TV/VCR Combos . . . . . . . . . . . . . . . . . . . . . . . 58

Setup Codes For VCRs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

2

Atlas DVR M1055F1 9/3/04 7:30AM Page 2

INTRODUCTION

The Cogeco Atlas DVR 5-Device Universal Remote

Control by Universal Electronics is our latest generation

universal remote control.Its sophisticated technology

allows you to consolidate up to five of your original home

entertainment remote controls into one easy-to-use product.

Moreover,it’s packed with advanced features such as:

• Preprogrammed control to operate the digital cable

receiver supplied by your cable service provider

• Dedicated keys to control popular functions on your

DVR (Digital Video Recorder)

• Programmable Master Power key for master on/off

control of your home entertainment equipment with a

single keystroke

• Instant “Tune-In”keys for assignment to your

favorite channels

• Channel Lock to lock channel selection only to the dig-

ital cable receiver

• Volume Lock to lock volume controls to one mode or

individual modes

• Device Key Re-Assignment to remotely control

a second (duplicate) device

• Code Search to help program control of older or

discontinued components

• Color-coded keys to quickly locate popular functions

• Code library for popular video and audio devices

Before using the product, you will need to install the

enclosed batteries and also perform some programming

to operate the specific home entertainment devices you

wish to control.

Please follow the instructions detailed in this manual to

set up the unit and then start enjoying your new remote

control and cable service.

3

Atlas DVR M1055F1 9/3/04 7:30AM Page 3

FEATURES AND FUNCTIONS

Use the illustration below to locate features on the

Cogeco Atlas DVR 5-Device Universal Remote Control

and then study the Key Charts (on the next three pages)

to learn how they function.

To find out what type of devices can be controlled by each

device key after programming, see the Device Table on

page 8.

4

Atlas DVR M1055F1 9/3/04 7:30AM Page 4

Key Charts

Use SETUP for all programming

sequences.

Press PWR once to turn on or

off a home entertainment device.

For MASTER POWER control, see

Using The Master Power Key on

page 18.

Press AUX,DVD, AUD,TV,or CBL

once to select a home entertain-

ment device to control.Also see

the Device Table on page 8.

Each device key has an embedded

LED (red light) that blinks upon

selection and indicates the remote

control is working and (after pro-

gramming) is sending signals.

Use GUIDE to display the program

guide.

Press MENU/SETTINGS once to dis-

play available interactive services.

Use INFO to display the current

channel and program information.

Use DAY+ (or DAY-) to move a day

forward (or back) on your digital

cable receiver’s program guide.

Use the Cursor keys to move the

cursor in the program guide and

menu screens and to navigate

within the interactive service.

Use OK/SELECT to choose options,

PPV events,and to tune programs

from the program guide.

Use PAGE+ (or PAGE-) to page up

(or page down) through menu

screens and the program guide.

Use EXIT to exit out of your digital

cable receiver’s menu and guide.

Use A,B,or C to access additional

cable features.

continued on next page...

5

Atlas DVR M1055F1 9/3/04 7:30AM Page 5

FEATURES AND FUNCTIONS

Key Charts (continued)

Use VOL+ (or VOL-) to raise (or

lower) the audio volume.

Use FAV to cycle through your

favorite channels stored in your

digital cable receiver.

Use CH+ (or CH-) to select the

next higher (or lower) channel.

For DVD players, use these keys to

skip forward (or reverse) through

chapters.

For amplifiers/receivers, use these

keys to select the next higher (or

lower) preset station.

Press MUTE once to turn the

sound off or on.

Press LAST once to recall the last

channel.

Press VOD once to access the Video

On Demand menu.

Press MUSIC once to access the

available digital music channels.

After programming (see page 16),

press F1 once to view up to five

favorite cable channel settings.

Use to command your DVR

to instantly replay the last

7 seconds of a program you are

watching.

Press LIST once to display a list

of recorded shows on your DVR.

Press LIVE to return to watching

live TV.

6

Atlas DVR M1055F1 9/3/04 7:30AM Page 6

In all modes except CBL,use REW,

PLAY,FFWD,STOP,andPAUSE to

control a VCR, DVD player, or a

DVR (after selecting a desired

device).To record in the VCR

mode, press REC twice.

In the CBL mode,use above keys

to control DVR functions of the

digital cable receiver.

Use the keypad numbers (1~ 9,

and 0) to directly tune channels

(e.g., 09). For amplifiers/receivers,

use the keypad numbers to select

inputs 1 through 10.

Press HD/ZOOM once to change

the aspect ratio of the show you

are watching. (Not available on all

set-top boxes).

Use PIP ON-OFF to switch the

Picture-In-Picture feature on or

off (if available on your TV or

cable service).

Use PIP SWAP to switch images

and sound between the main and

window pictures.

Use PIP MOVE to move the window

picture to different positions in the

main picture.

Use PIP CH+ (or CH-) to select

the next higher (or lower) PIP

channel.

In the CBL mode,use VIDEO

SOURCE to view other video

sources (A or B) instead of cable.

In all other modes,use VIDEO

SOURCE to watch TV or video

programs on a desired device. For

amplifiers/receivers,use VIDEO

SOURCE to select an input source.

7

Atlas DVR M1055F1 9/3/04 7:30AM Page 7

FEATURES AND FUNCTIONS (continued)

Device Table

NOTE: Please refer to the table below when performing the

instructions in “Programming Device Control” on page 10 or

“Programming TV/ VCR Combo Control” on page 12.

After programming, the Cogeco Atlas DVR 5-Device

Universal Remote Control will be able to control the

following types of devices:

8

DEVICE KEY CONTROLS THESE TYPES OF DEVICES

VCR, TV/VCR Combo, DVR

(Digital Video Recorder), or

extra DVD Player

DVD Player

Audio Amplifier, Tuner, or

Receiver

Telev i sion

Digital Cable Receiver or

Satellite Receiver

Atlas DVR M1055F1 9/3/04 7:30AM Page 8

INSTALLING BATTERIES

1. On the back of the remote control, push the

tab and lift off the battery cover.

2. Locate the two (2) enclosed AA batteries.

Match the + and – marks with those in the

battery case, then insert them.

3. Align the cover’s keys with the case’s holes

and press the cover back into place.The tab

should click when the cover is locked.

4. Test the remote control by pressing

any mode key (e.g.,TV). If the batteries are

inserted correctly, the LED (red light) will

blink once

NOTE: When batteries need replacement, the remote control will

cease to operate. Replace the batteries and the unit will be restored

to its full functionality, complete with your favorite settings.

9

❶

❸

❷

Atlas DVR M1055F1 9/3/04 7:30AM Page 9

PROGRAMMING DEVICE CONTROL

The Cogeco Atlas DVR 5-Device Universal Remote Control

is preprogrammed to operate the Motorola digital cable

receiver provided by your cable system, an RCA TV, a

Toshiba DVD player, an RCA VCR (as an AUX device),and

a Pioneer audio receiver. To control devices other than the

default brands, perform the following steps; otherwise

skip this section:

NOTE: For TV/VCR Combo control, skip this section and perform

the instructions on page 12. Also refer to the “Device Table” on

page 8 to find out which devices can be programmed onto each

device key.

1. Turn on a device and, if applicable, insert

video media, (e.g.,cassette or disc).

NOTE: Please read steps 2 through 4 completely

before proceeding. Highlight or write down the codes

and device you wish to program before moving on to

step 2.

2. On the remote control,press a device key once

(i.e.., AUX, DVD, AUD, TV,or CBL); it will blink

once. Then press and hold SETUP until the

selected mode key blinks twice, then release

SETUP.

3. Use the Manufacturer’s Codes (starting on

page 46) to locate the type of device and

brand name and then enter the first four-digit

code for your device.If performed correctly,

the selected mode key will blink twice.

NOTE: If the selected mode key emits a long blink,

the entry is invalid. Repeat steps 2 through 3 and try

entering the same code again.

4. Aim the remote control at the device and

press PWR once. The device should turn off.

If it does not, repeat steps 2 through 3, trying

each code for your brand until you find one

that works. If it still does not respond, try

searching for the code (see Searching For Your

Code on page 13).

NOTE: If the device does not have a

POWER

key,

press the (

Play

) key.

5. Repeat steps 1 through 4 for each device you

want the remote control to operate. For future

reference,write down each working device

code the boxes on the next page:

10

Atlas DVR M1055F1 9/3/04 7:30AM Page 10

AUX Code

Device Type:_______________________

DVD Code

Device Type:_______________________

AUD Code

Device Type:_______________________

CBL Code

Device Type:_______________________

TV Code

11

Atlas DVR M1055F1 9/3/04 7:30AM Page 11

PROGRAMMING TV/VCR COMBO CONTROL

If you own a TV/VCR Combo,perform the following

instructions to control this device:

1. Turn on your TV/VCR Combo and insert a

video cassette.

2. On the remote control, press AUX once; it will

blink once.Then press and hold SETUP until

the AUX key blinks twice,then release SETUP.

3. Use the Setup Codes For TV/VCR Combos (on

page 58) to locate the brand name and then

enter the first four-digit code for your TV/VCR

Combo.If you perform this procedure

correctly,the AUX key will blink twice.

NOTE: If the

AUX

key did not blink twice after

entering the code’s last digit, then repeat steps 2

through 3 and try entering the same code again.

If you’ve located a TV/VCR setup code that

works for your TV/VCR Combo and a separate

TV code is also listed,you’ll need to program

this code into the remote control to access

volume control (see Programming Device

Control on page 10).

4. Aim the remote control at your TV/VCR

Combo and press PWR once. The device

should turn off.If it does not respond,repeat

steps 2 through 3, trying each code listed for

your brand until you find one that works.

If it still does not respond,try searching for

the code (see Searching For Your Code on the

page 13).

5. For future reference, write down each working

device code in the boxes below:

TV/VCR Code

TV Code

(if used)

12

Atlas DVR M1055F1 9/3/04 7:30AM Page 12

SEARCHING FOR YOUR CODE

If your home entertainment device does not respond to

the Cogeco Atlas DVR 5-Device Universal Remote Control

after trying all of the codes listed for your brand,or if

your brand is not listed at all, try searching for your code.

For example,to search for a code for your TV:

1. Turn on your TV.

2. On the remote control, press TV once; it will

blink once.Then press and hold SETUP until

the TV key blinks twice,then release SETUP.

3. Enter 9 - 9 - 1.The TV key will blink twice.

4. Aim the remote control at the TV and press

PWR once.

5. Press CH+ one or more times and stop when

the TV turns off.

NOTE: In the search mode, the remote control will

send IR codes from its library to the selected

device, starting with the most popular code first.

6. Press SETUP once to lock in the code. The TV

key will blink twice.

7. To search for the codes of your other devices,

repeat steps 1 through 5, but substitute the

appropriate key (e.g.,AUX, DVD, AUD, or CBL)

for the device you are searching for.

13

Atlas DVR M1055F1 9/3/04 7:30AM Page 13

CHECKING THE CODES

If you have set up the Cogeco Atlas DVR 5-Device Universal

Remote Control using the Searching For Your Code proce-

dure (on the previous page),you may need to find out

which four-digit code is operating your equipment.

For example,to find out which code is operating your TV:

1. On the remote control, press TV once; it will

blink once.Then press and hold SETUP until

the TV key blinks twice,then release SETUP.

2. Enter 9 - 9 - 0.The TV key will blink twice.

3. To view the code for the first digit,press 1

once.Wait 3 seconds and count the number

of times the TV key blinks (e.g., 3 blinks = 3)

and write down the number in the leftmost

TV Code box on page 11.

NOTE: If a code digit is “0”, the selected mode key

will not blink.

4. Repeat step 3 three more times for the

remaining digits. Use 2 for the second digit,

3 for the third digit, and 4 for the fourth digit.

Finish writing down the code in the TV Code

boxes on page 11.

5. To check for other device codes,repeat steps

1 through 4, but substitute the appropriate key

(e.g., AUX, DVD, AUD, or CBL) for the device

you are checking.Write down the codes in the

appropriate boxes on page 11.

14

Atlas DVR M1055F1 9/3/04 7:30AM Page 14

15

PROGRAMMING CHANNEL CONTROL LOCK

By default,the Cogeco Atlas DVR 5-Device Universal

Remote Control’s channel-control capabilities are unlocked.

NOTE: This feature does not affect the

AUD

mode.

To Activate Channel Control Lock:

1. On the remote control, press CBL once; it will

blink once.Then press and hold SETUP until

the CBL key blinks twice,then release SETUP.

2. Enter 9 -7- 3.The CBL key will blink twice.

3. Press CH+ once. The CBL key will blink twice.

4. Now, regardless of what mode you select

(except AUD),only the channel control

capability of your cable converter will be

accessible.

To De-Activate Channel Control Lock:

1. On the remote control, press CBL once; it will

blink once.Then press and hold SETUP until

the CBL key blinks twice,then release SETUP.

2. Enter 9 -7- 3.The CBL key will blink twice.

3. Press CH- once. The CBL key will blink

four times.

4. Now, the remote control will provide TV and

VCR channel-control capabilities while in the

TV or VCR mode.

Atlas DVR M1055F1 9/3/04 7:30AM Page 15

16

PROGRAMMING THE F1 KEY

FOR SPECIFIC CHANNELS

The Cogeco Atlas DVR 5-Device Universal Remote Control

includes a programmable F1 key (located directly below the

LAST key).

The F1 key can be programmed to remember five of your

favorite cable channel settings. If you want to change the

cable channels previously-programmed on the F1 key,

you’ll need to clear the key first (see the next page).

To Program The F1 Key:

1. On the remote control, press CBL once; it will

blink once.Then press and hold SETUP until

the CBL key blinks twice,then release SETUP.

2. Enter 9 - 9 - 5.The CBL key will blink

twice. Then select the F1 key and press

it once.

3. Press CBL once followed by the channel

number to be programmed (e.g.,0 - 3 - 9).

4. Press and hold SETUP until the CBL key blinks

twice, then release SETUP.

5. To add another channel,repeat steps 1

through 4, substituting the new channel to be

added in step 3.

NOTE: Programming more than five channels on the

same

F1

key will overwrite previous settings.

Atlas DVR M1055F1 9/3/04 7:30AM Page 16

17

To Clear The F1 Key:

1. On the remote control, press CBL once; it will

blink once.Then press and hold SETUP until

the CBL key blinks twice,then release SETUP.

2. Enter 9 - 9 - 5.The CBL key will blink

twice. Then select the F1 key and press

it once.

3. Press and hold SETUP until the CBL key blinks

twice, then release SETUP.

4. The F1 key is now clear and ready for

reprogramming (see To Program The F1 Key

on the previous page).

Atlas DVR M1055F1 9/3/04 7:30AM Page 17

18

USING THE MASTER POWER KEY

The Cogeco Atlas DVR 5-Device Universal Remote Control

has a unique feature that allows you to sequentially turn

on or off up to five of your home entertainment devices

with a single key press.

NOTE:

MASTER POWER

(

PWR

) only works in the CBL mode. If it

is not programmed, only the cable converter will turn on or off.

In any other mode, pressing

MASTER POWER

(

PWR

) once will

turn on or off the selected device.

To Program The Master Power Key:

1. On the remote control, press and hold SETUP

until the last-selected device key blinks twice,

then release SETUP.

2. Enter 9 - 9 - 5.The last-selected device key

will blink twice. Then press PWR once.

3. For the first device you want in the power on

sequence, press a device key (e.g.,CBL) once .

Then press PWR once.

4. Repeat step 3 up to four more times to add the

second,third, fourth,and fifth device,as desired.

5. To save the settings and exit the program, press

and hold CBL once.Next press and hold

SETUP until the CBL key blinks twice, then

release SETUP.

To Operate The Master Power Key:

1. After programming, point the remote control

at the devices. Press CBL once.

2. Press PWR once to sequentially turn on or off

all home entertainment devices.

3. You will see the devices turn on or off

according to the programmed sequence.

Atlas DVR M1055F1 9/3/04 7:30AM Page 18

19

To Clear The Master Power Key:

1. Perform steps 1 and 2 in the first section

above, To Program The Master Power Key.

2. To clear the settings and exit the program,

press and hold SETUP until the CBL key blinks

twice, then release SETUP.

RE-ASSIGNING DEVICE KEYS

The Cogeco Atlas DVR 5-Device Universal Remote Control

can be set up to control a second device. For example, to

have the unit control a TV, a digital cable receiver, and two

DVD players, you will need to re-assign the unused AUX

key to operate the second DVD Player as follows:

NOTE:

AUX

is preset at the factory to control an RCA VCR.

Performing the below steps will overwrite those settings.

1. On the remote control, press AUX once; it will

blink once.Then press and hold SETUP until

the AUX key blinks twice,then release SETUP.

2. Enter 9 - 9 - 2.The AUX key will blink twice.

3. Press DVD once, then press AUX once. The

AUX key will blink twice.

4. The AUX key is now ready to be programmed

for your second DVD player. See Programming

Device Control on page 10.

To re-assign other device keys, repeat steps 1 to 4 and

substitute the key sequence using the following chart:

NOTE: Only one device can be assigned to an unused device key

at a time.

continued on next page...

Atlas DVR M1055F1 9/3/04 7:30AM Page 19

20

RE-ASSIGNING DEVICE KEYS (continued)

To Re-Assign Perform Key Sequence

AUX as 2nd AUD key: AUX - SETUP - 9 - 9 - 2 - AUD - AUX

AUX as 2nd TV key: AUX - SETUP - 9 - 9 - 2 - TV - AUX

AUX as 2nd CBL key: AUX - SETUP - 9 - 9 - 2 - CBL - AUX

AUX back to AUX: AUX - SETUP - 9 - 9 - 2 - AUX - AUX

To re-assign another unused device key, substitute it for

the AUX key above and then perform the sequence. For

example,to re-assign an unused AUD key as a second DVD

key, perform AUD - SETUP - 9 - 9 - 2 - DVD - AUD.

When a re-assignment is done, the selected device key

(e.g., AUD) will blink twice to confirm your choice.At that

time, you will need to program device control (see

Programming Device Control on page 10).

CHANGING VOLUME LOCK

On this remote control, the volume is unlocked so that

you have independent control of each programmed

device’s volume controls. If desired, you can still perform

Individual Volume Unlock on a selected device to set its

volume control for independent operation.

NOTE: The audio mode’s volume controls are active regardless of

Volume Lock settings. However, if you lock the volume controls to

the

AUD

mode, you will have control of the audio device’s volume

in all other modes (i.e.,

AUX

,

DVD

,

TV

,and

CBL

).

Locking Volume Control To A Specific Device

(Individual Volume Unlock):

1. Assuming Global Volume Lock is active, select

a mode on the remote control that you want to

unlock (e.g.,CBL) and press it once.Next,

press and hold SETUP until the device key

blinks twice, then release SETUP.

2. Enter 9 - 9 - 3.The last-selected device key

will blink twice.

3. Press VOL- once.The last-selected device key

will blink four times.

Atlas DVR M1055F1 9/3/04 7:30AM Page 20

La page charge ...

Universal Electronics COGECO ATLAS DVR 5-DEVICE Manuel utilisateur

Ce manuel convient également à

Universal Electronics COGECO ATLAS DVR 5-DEVICE Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents