ESAB QWT-120 Wire Cutting Station Guide d'installation

Marque: ESAB

Modèle: QWT-120 Wire Cutting Station

Taper: Guide d'installation

PHASE

GTAW

SMAW

INVERTER

115

230

WIRE CUTTING

STATION

Installation and Operation

Guide

English

Français

Español

QWT-120

Revision No: A Issue Date: November 12, 2008 Manual No: SM-QWT-120

PHASE

GTAW

SMAW

INVERTER

115

230

Congratulations on your new Tweco

Robotics product. We are proud

to have you as our customer and will strive to provide you with the

best service and reliability in the industry. This product is backed by

our extensive warranty and world-wide service network. To locate your

nearest distributor or service agency, please contact a representative at

the address and phone number in your area listed on the inside back

cover of this manual, or visit us on the web at www.tweco.com.

This Operating Manual has been designed to instruct you on the correct

use and operation of your Tweco

Robotics product. Your satisfaction

with this product and its safe operation is our ultimate concern.

Therefore, please take the time to read the entire manual, especially the

Safety Precautions. They will help you to avoid potential hazards that

may exist when working with this product.

YOU ARE IN GOOD COMPANY!

The Brand of Choice for Contractors and Fabricators Worldwide.

Tweco

Robotics is a Global Brand of Arc Welding Products for

Thermadyne Industries Inc. We manufacture and supply to major

welding industry sectors worldwide including; Manufacturing,

Construction, Mining, Automotive, Aerospace, Engineering, Rural and

DIY/Hobbyist.

We distinguish ourselves from our competition through market-leading,

dependable products that have stood the test of time. We pride ourselves

on technical innovation, competitive prices, excellent delivery, superior

customer service and technical support, together with excellence in

sales and marketing expertise.

Above all, we are committed to develop technologically advanced

products to achieve a safer working environment within the welding

industry.

WE APPRECIATE YOUR BUSINESS!

WARNING

READ AND UNDERSTAND THIS ENTIRE MANUAL AND YOUR EMPLOYER’S SAFETY PRACTICES BEFORE INSTALLING,

OPERATING, OR SERVICING THE EQUIPMENT.

WHILE THE INFORMATION CONTAINED IN THIS MANUAL REPRESENTS THE MANUFACTURER’S BEST JUDGMENT, THE

MANUFACTURER ASSUMES NO LIABILITY FOR ITS USE.

Wire Cutting Station

Installation and Operation Guide

Instruction Manual Number SM-QWT-120

Published by:

Tweco

Products Inc.

2800 Airport Road

Denton, TX 76208

(940) 566-2000

www.tweco.com

Thermadyne Industries Inc.

Reproduction of this work, in whole or in part, without written permission of the publisher is prohibited.

The publisher does not assume and hereby disclaims any liability to any party for any loss or damage caused by any

error or omission in this Manual, whether such error results from negligence, accident, or any other cause.

Publication Date: November 12, 2008

Record the following information for Warranty purposes:

Where Purchased: ________________________

Purchase Date: ________________________

Equipment Serial #: ________________________

wire cutting station

SM-QWT-120

Table of Contents

SECTION 1: SAFETY INSTRUCTIONS AND WARNINGS .......................................... 1-1

1.01 Welding Hazards .......................................................................................1-1

1.02 Principal Safety Standards ........................................................................1-3

1.03 Safety and Health ......................................................................................1-3

SECTION 2: INTRODUCTION AND DESCRIPTION ................................................. 2-4

2.01 How to Use this Manual ............................................................................2-4

2.02 Receipt of Equipment ................................................................................2-4

2.03 Introduction ..............................................................................................2-4

2.04 Features ....................................................................................................2-4

SECTION 3: INSTALLATION AND OPERATION .....................................................

3-5

SECTION 4: WIRING DIAGRAM ......................................................................

4-6

SECTION 5: REPLACEMENT PARTS .................................................................

5-7

SECTION 6: FACTORY REPAIR CENTER ............................................................ 6-8

LIMITED WARRANTY .................................................................................

6-9

wire cutting station

1-1

SM-QWT-120

SAFETY INSTRUCTIONS AND WARNINGS

SECTION 1:

SAFETY INSTRUCTIONS AND WARNINGS

WARNING

SERIOUS INJURY OR DEATH MAY RESULT IF WELDING AND CUTTING EQUIPMENT IS NOT PROPERLY INSTALLED,

USED AND MAINTAINED. MISUSE OF THIS EQUIPMENT AND OTHER UNSAFE PRACTICES CAN BE HAZARDOUS. THE

OPERATOR, SUPERVISOR, AND HELPER MUST READ AND UNDERSTAND THE FOLLOWING SAFETY WARNINGS AND

INSTRUCTIONS BEFORE INSTALLING OR USING ANY WELDING OR CUTTING EQUIPMENT.

THE WELDING AND CUTTING PROCESS IS USED IN MANY POTENTIALLY DANGEROUS ENVIRONMENTS SUCH

AS ELEVATED HEIGHTS, AREAS OF LIMITED VENTILATION, CLOSE QUARTERS, AROUND WATER, IN HOSTILE

ENVIRONMENTS, ETC., AND IT IS IMPORTANT THAT THE OPERATOR(S) ARE AWARE OF THE DANGERS ASSOCIATED

WITH WORKING IN THESE TYPES OF CONDITIONS. BE CERTAIN THAT THE OPERATOR(S) ARE TRAINED IN

SAFE PRACTICES FOR ENVIRONMENTS IN WHICH THEY ARE EXPECTED TO WORK AND UNDER COMPETENT

SUPERVISION.

IT IS ESSENTIAL THAT THE OPERATOR, SUPERVISOR AND ALL OTHER PERSONNEL IN THE WORK AREA ARE AWARE

OF THE DANGERS OF THE WELDING OR CUTTING PROCESS. TRAINING AND PROPER SUPERVISION ARE IMPORTANT

FOR A SAFE WORK PLACE. KEEP THESE INSTRUCTIONS FOR FUTURE USE. ADDITIONAL RECOMMENDED SAFETY

AND OPERATING INFORMATION IS REFERENCED IN EACH SECTION.

5. All ground connections must be checked periodically

to determine that they are mechanically strong and

electrically adequate for the required current.

6. When engaged in alternating current, welding, or

cutting under wet conditions or warm surroundings

where perspiration is a factor, the use of reliable

automatic controls for reducing the no-load voltage

is recommended to reduce shock hazard.

7. When the welding or cutting process requires values of

open circuit voltages in alternating current machines

higher than 80 volts, and direct current machines

higher than 100 volts, means must be provided to

prevent the operator from making accidental contact

with the high voltage by adequate insulation or other

means.

8. When welding is to be suspended for any substantial

length of time, such as during lunch or overnight,

all electrodes should be removed from the electrode

holder and the electrode holder carefully located so

that accidental contact cannot occur.

9. The holder must be disconnected from the power

source when not in use.

10.

Never immerse Mig-Guns, electrode holders, tig

torches, plasma torches, or electrodes in water.

WARNING

SMOKE, FUMES, AND GASES CAN BE DANGEROUS

TO YOUR HEALTH.

1.01 Welding Hazards

WARNING

ELECTRIC SHOCK CAN CAUSE INJURY OR DEATH.

INSTALL AND MAINTAIN EQUIPMENT IN ACCORDANCE

WITH THE NATIONAL ELECTRICAL CODE (NFPA 70)

AND LOCAL CODES. DO NOT SERVICE OR REPAIR

EQUIPMENT WITH POWER ON. DO NOT OPERATE

EQUIPMENT WITH PROTECTIVE INSULATORS

OR COVERS REMOVED. SERVICE OR REPAIR TO

EQUIPMENT MUST BE DONE BY A QUALIFIED REPAIR

TECHNICIAN, OR TRAINED PERSONNEL ONLY.

1. Do not touch live electrical parts.

Do not touch an electrode with bare skin and electrical

ground at the same time.

3. Always keep welding gloves dry and in good

condition.

NOTE

Aluminized protective clothing can become

part of the electrical path.

4. Keep oxygen cylinders, chains, wire ropes, cranes,

hoists, and elevators away from any part of the

electrical path.

wire cutting station

1-2

SM-QWT-120

SAFETY INSTRUCTIONS AND WARNINGS

21. Flammable hair preparations should not be used when

welding or cutting. Wear ear plugs to protect ears from

sparks.

22. Where the work area permits, the operator should be

enclosed in an individual booth painted with a ﬁnish of

low reﬂectivity such as zinc oxide. This is an important

factor for absorbing ultraviolet radiations, and lamp black.

The operator should be enclosed with non-combustible

screens similarly painted.

WARNING

WELDING SPARKS CAN CAUSE FIRES AND

EXPLOSIONS.

23. Causes of ﬁre and explosion are: combustibles reached by

the arc, ﬂame, ﬂying sparks, hot slag, or heated material.

Remove combustibles from the work area and/or provide

a ﬁre watch.

. Avoid oily or greasy clothing as sparks may ignite them. Have

a ﬁre extinguisher nearby, and know how to use it.

25.

Be alert to the danger of conduction or radiation. For

example, if welding or cutting is to be done on a metal

wall, partition, ceiling, or roof, precautions must be taken

to prevent ignition of combustibles on the other side.

26. Do not w

eld or cut containers that have held combustibles.

All hollow spaces, cavities and containers should be vented

prior to welding or cutting to permit the escape of air or

gases. Purging with inert gas is recommended.

27.

Never use oxygen in a welding torch. Use only inert

gases or inert gas mixes as required by the process. Use

of combustible compressed gases can cause explosions

resulting in personal injury or death. Arcing against any

compressed gas cylinder can cause cylinder damage or

explosion.

WARNING

NOISE CAN DAMAGE HEARING.

28. Noise from the air carbon-arc process can damage

your hearing. Wear protective hearing devices to ensure

protection when noise levels exceed OSHA standards.

Adequate hearing protection devices must be worn by

operators and surrounding personnel to ensure personal

protection against noise.

11. Keep smoke, fumes, and gases from the breathing area.

12. Fumes from the welding or cutting process are of various

types and strengths, depending on the kind of base metal

being worked on. To ensure your safety, do not breathe

these fumes.

13. Ventilation must be adequate to remove smoke, fumes,

and gases during the operation to protect operators and

other personnel in the area.

14. Vapors of chlorinated solvents can form the toxic gas

“Phosgene” when exposed to ultraviolet radiation from an

electric arc. All solvents, degreasers, and potential sources

of these vapors must be removed from the work area.

15. Fumes produced by welding or cutting, particularly in

conﬁned places, can cause discomfort and physical harm

if inhaled over an extended period of time.

16. Provide adequate ventilation in the welding or cutting area.

Use air-supplied respirators if ventilation is not adequate to

remove all fumes and gases. Never ventilate with oxygen.

Oxygen supports and vigorously accelerates ﬁre.

WARNING

ARC RAYS, HOT SLAG, AND SPARKS CAN INJURE

EYES AND BURN SKIN .

17. The welding and cutting processes produces extreme

localized heat and strong ultraviolet rays.

18. Never attempt to weld or cut without a welding helmet with

the proper lens. Ensure that the lens complies with federal

guidelines. A number 12 to 14 shade ﬁlter lens provides the

best protection against arc radiation. When in a conﬁned

area, prevent the reﬂected arc rays from entering around

the helmet.

19. Ensure all personnel in the work area are protected from

arc rays and sparks. Approved shielding curtains and

appropriate goggles should be used to provide protection

to staff in the surrounding area and operators of nearby

equipment.

20. Unprotected skin should also be covered from arc rays,

heat and molten metal. Always wear protective gloves and

clothing that does not allow skin to become exposed. All

pockets should be closed and cuffs sewn shut. Leather

aprons, sleeves, leggings, etc., should be worn for out-of-

position welding and cutting or for heavy operations using

large electrodes. High top work shoes provide adequate

protection from foot burns. For added protection use

leather spats.

wire cutting station

1-3

SM-QWT-120

SAFETY INSTRUCTIONS AND WARNINGS

1.02 Principal Safety Standards

1.03 Safety and Health

NOTE

Be sure to read and fully comprehend the safety

instuctions and warnings contained within

section 1 of this manual before performing

any welding or cutting operations.

WARNING

SERIOUS INJURY OR DEATH MAY RESULT IF

WELDING AND CUTTING EQUIPMENT IS NOT

PROPERLY INSTALLED, USED, AND MAINTAINED.

MISUSE OF THIS EQUIPMENT, OR OTHER UNSAFE

PRACTICES, CAN BE HAZARDOUS.

Electric shock can cause injury or death.

Smoke, fumes, and gases can be dangerous to your

health.

Arc rays, hot slag, and sparks can injure or burn

unprotected eyes and skin.

Welding sparks can cause ﬁres and explosions.

Excessive noise can damage your hearing.

•

SAFETY AND OPERATING REFERENCES

1. Code of Federal Regulations. (OSHA)

Section 29 Part 1910.95, 132, 133, 134, 139, 251, 252, 253, 254 and 1000.

U.S. Government Printing Ofﬁce, Washington, DC. 20402.

2. ANSl Z49.1 “Safety In Welding and Cutting”.

3. ANSI Z87.1 “Practice for Occupational and Educational Eye and Face Protection”.

4. ANSl Z88.2 “Standard Practice for Respiratory Protection”.

American National Standards Institute, 1430 Broadway, New York, NY. 10018.

5. AWS F4.1 “Recommended Safe Practices for Welding and Cutting Containers”.

6. AWS C5.3 “Recommended Practices for Air Carbon-Arc Gouging and Cutting”.

The American Welding Society, 550 NW Lejeune RD., P.O.Box 351040, Miami FL. 33135.

7. NFPA 51B “Fire Prevention in Cutting and Welding Processes”.

8. NFPA-7 “National Electrical Code”.

National Fire Protection Association, Battery Park, Quincy, MA. 02269.

9. CSA W117.2, “Safety in Welding, Cutting and Allied Processes”.

Canadian Standards Association, 178 Rexdale Blvd., Rexdale, Ontario, Canada M9W 1R3.

Warning

This producT conTains chemicals, including

lead, or oTherWise produces chemicals knoWn

To The sTaTe of california To cause cancer,

birTh defecTs and oTher reproducTive harm.

Wash hands after handling. (california

healTh & safeTy code § 25249.5 eT seq.)

wire cutting station

2-4

SM-QWT-120

INTRODUCTION AND DESCRIPTION

2.01 How to Use this Manual

To ensure safe operation, read the entire manual, including

the chapters on safety instructions and warnings.

Throughout this manual, the words WARNING, CAUTION,

and NOTE may appear. Pay particular attention to the

information provided under these headings. These special

annotations are easily recognized as follows:

WARNING

A WARNING GIVES INFORMATION REGARDING

POSSIBLE PERSONAL INJURY.

CAUTION

A CAUTION refers to possible equipment

damage.

NOTE

A NOTE offers helpful information concerning

certain operating procedures.

2.02 Receipt of Equipment

When you receive the equipment, check it against the

invoice to make sure it is complete and inspect the

equipment for possible damage due to shipping. If there is

any damage, notify the carrier immediately to ﬁle a claim.

Furnish complete information concerning damage claims

or shipping errors to the location in your area listed in the

inside back cover of this manual. Include a full description

of the parts in error.

If you want additional or replacement copies of this CD,

please contact Tweco

Robotics at the address and phone

number in your area listed on the inside back cover of this

manual. Include the Manual number (from page i) and

CD part number: 64-2601.

2.03 Introduction

The Tweco

Robotics QWT-120 Quick Wire Trimmer, is

an on-the-ﬂy wire trimming station furnished with dual

cutting wheels as shown in Figure 1 that cleanly shear the

wire without deﬂection or bending of the welding wire.

SECTION 2:

INTRODUCTION AND DESCRIPTION

2.04 Features

Machined discs from heat-treated tool steel for long

life and economical performance.

Reversible cutting discs, doubles the disc’s life span,

designed for convenient replacement.

Unit is powered by a 120-volt AC motor with a relay

interface for controlling the start and stop cycle

through the robotic controller.

Unit is enclosed in a heavy-gauge aluminum tube,

with the head assembly machined from solid

aluminum.

Industrial components provide years of reliable

service.

The unit is able to cut the following wire sizes:

Steel Wire From .023” (0,6mm) to 5/64” (2,0mm)

Aluminum

Wire

From .030” (0,8mm) to 3/32” (3,2mm)

Flux Cored

Wire

From .030” (0,8mm) to 3/32” (3,2mm)

Metal Cored

Wire

From .030: (0,8mm) to 3/32” (3,2mm)

•

5.00”

(127mm)

17.00”

(432,5mm)

7.50”

(190,5mm)

5.00”

(126,4mm)

Figure 1

wire cutting station

3-5

SM-QWT-120

INSTALLATION AND OPERATION

SECTION 3:

INSTALLATION AND OPERATION

1. Remove the QWT-120 Wire Trimmer from the shipping

carton.

2. Mount the QWT-120 unit onto a solid work table within

the envelope of the robot.

NOTE

The cutting path should be within reach of the

end of the welding wire, at the desired angle

of cut. The unit may be mounted in a vertical

upright position, or at an angle of up to 30°.

The mounting plate has four .406” Ø (11,03mm)

holes that allow the use of 3/8” Ø (9,53mm)

hex head bolts to secure the unit to the

worktable. Refer to Figure 2.

Figure 2: Mounting Hole Location

7.12”

(180,8mm)

4.12”

(104,6mm)

8.00”

(203,2mm)

5.00”

(127mm)

Ø 0.406”

(11,03mm)

3. Lay out the hole pattern on the work table surface.

Drill the four holes and secure the QWT-120 unit to

the work table surface.

4. Plug the 120-volt AC power cord into the appropriate

receptacle.

The motor is controlled by a 24-volt DC relay circuit

built into the unit. The operational mode switch

activates the relay circuit. The unit comes with a 22/2

PVC control cable to receive the 24-volt DC signal

from the robot controller to the QWT-120 unit. Refer

to Section 4: Wiring Diagram.

5. Connect the 2 conductor control wires to the

robot controller per the robot manufacture’s

recommendations.

A three position toggle switch is located on the outer

housing of the QWT-120 unit. Refer to Figure 3.

Figure 3: Test/Off/Auto Toggle Switch

The 3-position toggle switch is used as follows:

TEST (UP) Allows the unit to function as long as

the switch is held in the UP position.

NOTE

Do not run the unit continuous, this may cause

overheating of the unit.

OFF (CENTER) Allows the unit to be turned off.

AUTO (DOWN) Allows the unit to be controlled ON or

OFF by the robot controller using the

24-volt DC signal.

6. Set the unit to the AUTO position.

7. The QWT-120 Unit is now ready to be used.

wire cutting station

4-6

SM-QWT-120

SECTION 4:

WIRING DIAGRAM

(MOMENTARY) TEST

OFF

AUTO

SWITCH

CAP

MOTOR

BLUE

BROWN

GREEN

POWER CORD

120 V AC

SIGNAL

24V DC

BLACK

RED

CONTROL WIRE

Wiring Diagram

wire cutting station

5-7

SM-QWT-120

REPLACEMENT PARTS

SECTION 5:

REPLACEMENT PARTS

Part No. QWT-120-9

(Stock No. 3500-1309)

Part No. QWT-120-6

(Stock No. 3500-1306)

Part No. QWT-120-19

(Stock No. 3500-1319)

Part No. QWT-120-2

(Stock No. 3500-1302)

Part No. QWT-120-4

(Stock No. 3500-1304)

Part No. QWT-120-20

(Stock No. 3500-1320)

wire cutting station

6-8

SM-QWT-120

FACTORY REPAIR CENTER

SECTION 6:

FACTORY REPAIR CENTER

Tweco

Robotics Factory Repair Center (FRC) offers a repair service for our customers on the various cable assemblies and

peripheral products. The majority of our consumers do not want to spend the time involved with repairs and generally do not

have the necessary equipment and tools to perform repairs.

Other key beneﬁts in considering the “FRC” service repairs on your product:

All products will be rebuilt and tested following the established test procedures and speciﬁcations for the speciﬁc

product.

All repairs are done using original Tweco

Robotics parts to ensure maximum product performance.

Our FRC has highly-trained employees utilizing the appropriate tools and test equipment.

Factory Repair Center

Domestic Toll Free Phone Number: 1-800-426-1888

Fax Number: 1-620-229-9926

•

STATEMENT OF WARRANTY

LIMITED WARRANTY: THERMADYNE

warrants that its products will be free of defects in workmanship or material. Should

any failure to conform to this warranty appear within the time period applicable to the THERMADYNE products as stated below,

THERMADYNE shall, upon notiﬁcation thereof and substantiation that the product has been stored, installed, operated, and

maintained in accordance with THERMADYNE’s speciﬁcations, instructions, recommendations and recognized standard industry

practice, and not subject to misuse, repair, neglect, alteration, or accident, correct such defects by suitable repair or replacement,

at THERMADYNE’s sole option, of any components or parts of the product determined by THERMADYNE to be defective.

THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY

WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

LIMITATION OF LIABILITY:

THERMADYNE shall not under any circumstances be liable for special or consequential damages,

such as, but not limited to, damage or loss of purchased or replacement goods, or claims of customers of distributor (hereinafter

the “Purchaser”) for service interruption. The remedies of the Purchaser set forth herein are exclusive and the liability of

THERMADYNE with respect to any contract, or anything done in connection therewith such as the performance or breach

thereof, or from the manufacture, sale, delivery, resale, or use of any goods covered by or furnished by THERMADYNE whether

arising out of contract, negligence, strict tort, or under any warranty, or otherwise, shall not, except as expressly provided

herein, exceed the price of the goods upon which such liability is based.

THIS WARRANTY BECOMES INVALID IF REPLACEMENT PARTS OR ACCESSORIES ARE USED WHICH MAY IMPAIR THE

SAFETY OR PERFORMANCE OF ANY THERMADYNE PRODUCT.

THIS WARRANTY IS INVALID IF THE PRODUCT IS SOLD BY NON-AUTHORIZED PERSONS.

This warranty is effective for the time stated in the Warranty Schedule beginning on the date that the authorized distributor

delivers the products to the Purchaser.

Warranty repairs or replacement claims under this limited warranty must be submitted by an authorized THERMADYNE repair

facility within thirty (30) days of the repair. No transportation costs of any kind will be paid under this warranty. Transportation

charges to send products to an authorized warranty repair facility shall be the responsibility of the Purchaser. All returned goods

shall be at the Purchaser’s risk and expense. This warranty supersedes all previous THERMADYNE warranties.

WARRANTY SCHEDULE

The warranty is effective below for the time stated in the Warranty Schedule beginning on the date that the authorized

distributor delivers the products to the purchaser. THERMADYNE

reserves the right to request documented evidence of date

of purchase.

Engine Driven Welders Parts / Labor

Scout

, Raider

, Explorer™

Original Main Power Stators and Inductors 3 years / 3 years

Original Main Power Rectiﬁers, Control P.C. Boards 3 years / 3 years

All Other Original Circuits and Components Including, but not Limited to, Relays, Switches, Contactors, Solenoids, Fans, Power Switch Semi-Conductors 1 year / 1 year

Engines and Associated Components are NOT Warranted by Thermal Arc

, Although Most are Warranted by the Engine Manufacturer. SEE THE ENGINE

MANUFACTURERS’ WARRANTY FOR DETAILS.

See the Engine Manufacturers’ Warranty

for Details

GMAW/FCAW (MIG) Welding Equipment Parts / Labor

Fabricator

131, 181, 190, 210, 251, 281; Fabstar

4030; PowerMaster

350, 350P, 500, 500P; Excel-Arc

6045; Wire Feeders: Ultrafeed

, Porta-feed

Original Main Power Transformer and Inductor 5 years / 3 years

Original Main Power Rectiﬁers, Control P.C. Boards, Power Switch Semi-Conductors 3 years / 3 years

All Other Original Circuits and Components Including, but not Limited to, Relays, Switches, Contactors, Solenoids, Fans, Electric Motors 1 year / 1 year

GTAW (TIG) & Multi-process Inverter Welding Equipment Parts / Labor

160TS, 300TS, 400TS, 185AC/DC, 200AC/DC, 300AC/DC, 400GTSW, 400MST, 300MST, 400MSTP

Original Main Power Magnetics 5 years / 3 years

Original Main Power Rectiﬁers, Control P.C. Boards, Power Switch Semi-Conductors 3 years / 3 years

All Other Original Circuits and Components Including, but not Limited to, Relays, Switches, Contactors, Solenoids, Fans, Electric Motors 1 year / 1 year

Plasma Welding Equipment Parts / Labor

Ultima

150

Original Main Power Magnetics 5 years / 3 years

Original Main Power Rectiﬁers, Control P.C. Boards, Power Switch Semi-Conductors 3 years / 3 years

Welding Console, Weld Controller, Weld Timer 3 years / 3 years

All Other Original Circuits and Components Including, but not Limited to, Relays, Switches, Contactors, Solenoids, Fans, Electric Motors, Coolant Recirculators 1 year / 1 year

SMAW (Stick) Welding Equipment Parts / Labor

Dragster™ 85

Original Main Power Magnetics 1 year / 1 year

Original Main Power Rectiﬁers, Control P.C. Boards 1 year / 1 year

All Other Original Circuits and Components Including, but not Limited to, Relays, Switches, Contactors, Solenoids, Fans, Power Switch Semi-Conductors 1 year / 1 year

160S, 300S, 400S

Original Main Power Magnetics 5 years / 3 years

Original Main Power Rectiﬁers, Control P.C. Boards 3 years / 3 years

All Other Original Circuits and Components Including, but not Limited to, Relays, Switches, Contactors, Solenoids, Fans, Power Switch Semi-Conductors 1 year / 1 year

General Arc Equipment Parts / Labor

Water Recirculators 1 year / 1 year

Plasma Welding Torches 180 days / 180 days

Gas Regulators (Supplied with Power Sources) 180 days / NA

MIG and TIG Torches (Supplied with Power Sources) 90 days / NA

Replacement Repair Parts 90 days / NA

MIG, TIG and Plasma Welding Torch Consumable Items NA / NA

Gas Welding and Cutting Equipment Parts / Labor

Victor

Professional 5 years / NA

Oxygen Conservers 2 years / NA

Aluminum Cylinders Lifetime / NA

Cutting Machine Motors 1 year / NA

HP&I Brass Regulators/Manifolds 2 years / NA

HP&I Stainless Regulators/Manifolds 1 year / NA

HP&I Corrosive Gas Regulators/Manifolds 90 days / NA

TurboTorch

3 years / NA

CutSkill

2 years / NA

Steel Cylinders 1 year / NA

Victor Medical 6 years / NA

Victor VSP 2 years / NA

Firepower

MIG Welders 5-2-1 years / NA

Transformers 5 years / NA

Parts Used in Rental Applications

1 year from date sold by seller to authorized

distributor

MIG Torches and Arc Accessories Parts / Labor

Arcair

N6000 90 days / NA

Eliminator

Spool and Pull Guns 90 days / NA

Robotic Deﬂection Mounts 90 days / NA

QRM-100 Anti-Spatter Applicator 90 days / NA

TC and TCV Water Coolers 1 year / NA

TSC-96 Smoke Collector 1 year / NA

ESG-1, EPG-CR1, EPG-CR2 Control Boxes for Eliminator Spool & Pull Guns 1 year / NA

QRC-2000 Nozzle Cleaning Stations 1 year / 1 year

QRC-3000 UltraSonic Cleaning Stations 2 years / 2 years

All other products 30 days from date purchaser purchases from seller. 30 days / NA

Plasma Cutting Systems Parts / Labor

Automated Plasma 2 years / 1 year

CutMaster™ 3 years / 3 years

PakMaster

XL PLUS 3 years / 1 year

Drag-Gun

1 year / 1 year

Drag-Gun Plus 2 years / 1 year

Torches 1 year / 1 year

Consoles, Control Equipment, Heat Exchangers and Accessory Equipment 1 year / 1 year

W O R L D H E A D Q U A R T E R S : 1 6 0 5 2 S w i n g l e y R i d g e R o a d , S u i t e 3 0 0 • S t . Lo u i s , M i s s o u r i 6 3 0 1 7 U. S . A .

A Global Cutting & Welding Market Leader

™

Denton, TX USA

U.S. Customer Care

Ph: (1) 800-426-1888

Fax: (1) 800-535-0557

Miami, FL USA

Sales Office, Latin America

Ph: (1) 954-727-8371

Fax: (1) 954-727-8376

Oakville, Ontario, Canada

Canada Customer Care

Ph: (1) 905-827-4515

Fax: (1) 800-588-1714

International Customer Care

Ph: (1) 905-827-9777

Fax: (1) 905-827-9797

Chorley, United Kingdom

Customer Care

Ph: (44) 1257-261755

Fax: (44) 1257-224800

Milan, Italy

Customer Care

Ph: (39) 0236546801

Fax: (39) 0236546840

Cikarang, Indonesia

Customer Care

Ph: 62 21+ 8983-0011 / 0012

Fax: 62 21+ 893-6067

Osaka, Japan

Sales Office

Ph: 816-4809-8411

Fax: 816-4809-8412

Melbourne, Australia

Australia Customer Care

Ph: 1300-654-674

Fax: 613+ 9474-7391

International

Ph: 613+ 9474-7508

Fax: 613+ 9474-7488

Rawang, Malaysia

Customer Care

Ph: 603+ 6092-2988

Fax: 603+ 6092-1085

Shanghai, China

Sales Office

Ph: 86-21-64072626

Fax: 86-21-64483032

Singapore

Sales Office

Ph: 65+ 6832-8066

Fax: 65+ 6763-5812

THE AMERICAS EUROPE ASIA/PACIFIC

U.S. Customer Care: ARCAIR

/ STOODY

/ THERMAL ARC

/ THERMAL DYNAMICS

/ TWECO

/ VICTOR

................... 800-426-1888 / FAX 800-535-0557

FIREPOWER

................. 800-858-4232 / FAX 800-535-0557 TDC AUTOMATION................... 866-279-2628 / FAX 800-535-0557

TURBOTORCH

............. 800-238-0282 / FAX 800-535-0557 VICTOR MEDICAL .................... 800-382-8187 / FAX 800-535-0557

VICTOR SPECIALTY PRODUCTS ................... 800-569-0547 / FAX 800-535-0557

Canada Customer Care: 905-827-4515 / FAX 800-588-1714

•

International Customer Care: 905-827-9777 / FAX 905-827-9797

CIGWELD Customer Care: 1300-654-674 / FAX 613+ 9474-7391

•

www.thermadyne.com

PHASE

GTAW

SMAW

INVERTER

115

230

POSTE DE COUPE

DE FIL

Guide D’installation

et D’utilisation

English

Français

Español

QWT-120

Révision: A Date d’émission: 12 novembre 2008 No de Forma: SM-QWT-120

PHASE

GTAW

SMAW

INVERTER

115

230

VOTRE ACTIVITÉ NOUS INTÉRESSE!

Félicitations pour votre nouveau produit Tweco

. Nous sommes ﬁers de

vous avoir comme client et nous tâcherons de vous fournir les meilleurs

services et ﬁabilité dans l’industrie. Ce produit est soutenu par une vaste

garantie et un réseau mondial de service. Pour localiser votre distributeur

ou agence de service le plus proche, veuillez communiquer avec un

représentant à l’adresse ou au numéro de téléphone correspondant à

votre région, indiqué au verso de la couverture du manuel, ou visitez

notre site web www.tweco.com.

Ce Manuel d’utilisation a été conçu pour vous permettre d’utiliser et de

faire fonctionner correctement votre produit Tweco

. Votre satisfaction

et le fonctionnement en toute sécurité de votre produit sont nos

principaux soucis. Par conséquent, veuillez prendre le temps de lire

tout le manuel, spécialement en ce qui concerne les Précautions de

Sécurité. Ceci vous aidera à éviter d’éventuels accidents qui pourraient

survenir en travaillant avec ce produit.

VOUS ÊTES EN BONNE COMPAGNIE!

La Marque de Choix pour les Entrepreneurs et les Fabricants dans le Monde.

Tweco

Robotics est une marque globale de produits de soudage à l’arc

pour Thermadyne Industries Inc. Nous fabriquons et fournissons aux

plus grands secteurs de l’industrie de soudage dans le monde dont:

Fabrication, Construction, Exploitation Minière, Automobile, Aérospatial,

Ingénierie, Rural et Loisirs/Bricolage.

Nous nous distinguons de notre concurrence grâce à nos produits

en tête du marché, ﬁables, ayant résisté à l’épreuve du temps. Nous

sommes ﬁers de notre innovation technique, nos prix compétitifs, notre

excellente livraison, notre service clientèle et notre support technique

de qualité supérieure, ainsi que de l’excellence dans les ventes et

l’expertise en marketing.

Surtout, nous nous engageons à développer des produits utilisant des

technologies de pointe pour obtenir un environnement de travail plus

sécurisé dans l’industrie de la soudure.

AVERTISSEMENT

LISEZ ET COMPRENEZ TOUT LE MANUEL ET LES PRATIQUES DE SÉCURITÉ DE L’UTILISATEUR AVANT L’INSTALLATION,

LE FONCTIONNEMENT OU L’ENTRETIEN DE L’ÉQUIPEMENT. MÊME SI LES INFORMATIONS CONTENUES DANS CE MANUEL

REPRÉSENTENT LE MEILLEUR JUGEMENT DU FABRICANT, CELUI-CI N’ASSUME AUCUNE RESPONSABILITÉ POUR SON

USAGE.

Poste de Coupe de Fil

Guide D’installation et D’utilisation

Numéro du Manuel d’Instructions pour SM-QWT-120

Publié par:

Tweco

Products Inc.

2800 Airport Road

Denton, TX 76208

(940) 566-2000

www.tweco.com

Thermadyne Industries Inc.

La reproduction, de tout ou partie de ce manuel, sans l’autorisation écrite de l’éditeur, est interdite.

L’éditeur n’assume pas et dément toute responsabilité pour perte ou dommage causés à une partie par erreur ou

omission dans ce manuel, si une telle erreur résulte d’une négligence, d’un accident, ou de toute autre cause.

Date de Parution: 12 novembre 2008

Complétez les informations suivantes à des ﬁns de garantie:

Lieu D’achat: ________________________

Date D’achat: ________________________

Numéro de: ________________________

Poste de CouPe de Fil

SM-QWT-120

Table des Matiéres

SECTION 1: INSTRUCTIONS DE SÉCURITÉ ET MISES EN GARDE .............................F1-1

1.01 Accidents de Soudage ............................................................................. F1-1

1.02 Principales Normes de Sécurité ..............................................................F1-3

1.03 Sécurité et Santé .....................................................................................F1-3

SECTION 2: INTRODUCTION ET DESCRIPTION ..................................................F2-4

2.01 Comment Utiliser ce Manuel ...................................................................F2-4

2.02 Réception de L’équipement .....................................................................F2-4

2.03 Introduction ............................................................................................F2-4

2.04 Dispositifs ...............................................................................................F2-4

SECTION 3: INSTALLATION ET OPÉRATION ..........................................................

SECTION 4: SCHÉMA DE CÂBLAGE ................................................................

F4-6

SECTION 5: PIÈCES DE RECHANGE ................................................................

F5-7

GARANTIE .............................................................................................F6-8

TABLEAU DES GARANTIES ..........................................................................

F6-9

La page charge ...

ESAB QWT-120 Wire Cutting Station Guide d'installation

Marque: ESAB

Modèle: QWT-120 Wire Cutting Station

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: ESAB QWT-120 Wire Cutting Station Installation guide
español: ESAB QWT-120 Wire Cutting Station Guía de instalación

ESAB QWT-120 Wire Cutting Station Guide d'installation

ESAB QWT-120 Wire Cutting Station Guide d'installation

dans d''autres langues

Documents connexes

Autres documents