Sauder Palladia Collection 412902 Mode d'emploi

NOTE: THIS INSTRUCTION

BOOKLET CONTAINS IMPORTANT

SAFETY INFORMATION.

PLEASE READ AND KEEP FOR

FUTURE REFERENCE.

English pg 1-40

Français pg 41-46

Español pg 47-52

Lot # 398172 11/23/16

Purchased: __________________

Be sure to give us a ring before

making any returns. 1-800-523-3987

Executive Desk

Palladia Collection | Model 412902

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.

Prefer the phone? Call 1-800-523-3987.

Share your journey!

sauder.com

Get executive

with this decision.

Table of Contents Assembly Tools Required

2-4

5-7

8-40

41-46

47-52

53-54

55

Part Identiﬁ cation

Hardware Identiﬁ cation

Assembly Steps

Français

Español

Safety

Warranty

Hammer

Not actual size

No. 2 Phillips Screwdriver

Tip Shown Actual Size

Skip the power trip.

This time.

412902 www.sauder.com/servicesPage 2

Part Identiﬁ cation

å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge

to help distinguish similar parts from each other. Use this part identiﬁ cation to help identify similar parts.

A OUTER END (2)

B3 RIGHT END (1)

C3 LEFT END (1)

D2 RIGHT UPRIGHT (1)

D32 LARGE LEFT DRAWER SIDE (2)

D33 LARGE RIGHT DRAWER SIDE (2)

D34 SMALL RIGHT DRAWER SIDE (2)

D35 SMALL LEFT DRAWER SIDE (2)

D36 RIGHT DRAWER SIDE (2)

D37 LEFT DRAWER SIDE (2)

D74 SMALL DRAWER BACK (2)

D77 DRAWER BACK (2)

D78 LARGE DRAWER BACK (2)

D708 LARGE DRAWER BOTTOM (2)

D716 DRAWER BOTTOM (4)

E2 LEFT UPRIGHT (1)

F2 TOP (1)

G2 BOTTOM (2)

H2 MODESTY PANEL (1)

I BACK (1)

J PEDESTAL BACK (1)

K BRACE (4)

L DOOR (1)

M ADJUSTABLE SHELF (1)

M26 MOLDING (4)

N SKIRT (4)

O KEYBOARD FRONT (1)

P KEYBOARD BACK (1)

Q KEYBOARD SIDE (2)

R KEYBOARD SHELF (1)

S LARGE DRAWER BOX FRONT (2)

T LARGE RIGHT DRAWER FRONT (1)

U LARGE LEFT DRAWER FRONT (1)

Z DRAWER BOX FRONT (2)

AA RIGHT DRAWER FRONT (1)

BB LEFT DRAWER FRONT (1)

DD PLINTH (8)

FF SMALL RIGHT DRAWER FRONT (1)

GG SMALL LEFT DRAWER FRONT (1)

LL TOP REAR MOLDING (1)

MM UPPER BACK MOLDING (1)

NN SIDE MOLDING (2)

OO LOWER MOLDING (1)

PP UPPER MOLDING (1)

RR LEFT BOTTOM MOLDING (2)

TT RIGHT BOTTOM MOLDING (2)

UU TOP FRONT MOLDING (1)

VV HALF DISK (8)

Part Identiﬁ cation

Now you know

our ABCs.

412902www.sauder.com/services

Page 3

A

B3

C3

D2

E2

F2

G2

H2

I

J

K

L

M

N

DD

LL

MM

NN

OO

RR

UU

A

G2

K

N

DD

PP

NN

DD

TT

RR

VV

DD

TT

VV

M26

Part Identiﬁ cation

Now you know

our ABCs.

412902 www.sauder.com/servicesPage 4

O

P

Q

R

Q

S

T

US

Z

AA

BB

Z

FF

GG

D716

D708

D78

D33

D32

D37

D36

D77

D35

D34

D74

D32

D78

D33

D37

D77

D36

D34

D35

D74

Hardware Identiﬁ cation

å Screws are shown actual size. You may receive extra hardware with your unit.

412902www.sauder.com/services

Page 5

(EXTENSION SET SHOWN SEPARATED)

NARROW

EXTENSION RAIL - 8

AAA

NARROW

EXTENSION SLIDE - 8

BBB

WIDE

EXTENSION SLIDE - 4

DDD

FILE ROD - 4

WIDE

EXTENSION RAIL - 4

CCC

ZZ

LEFT DRAWER SLIDE - 1

RIGHT CABINET RAIL - 1

WW

LEFT CABINET RAIL - 1

XX

RIGHT DRAWER SLIDE - 1

YY

8B

FILE GLIDE - 4

6B

7F

TWIST-LOCK

®

FASTENER - 25

HIDDEN CAM - 8

1F

CAM DOWEL - 8

2F

Hardware Identiﬁ cation

å Screws are shown actual size. You may receive extra hardware with your unit.

412902 www.sauder.com/servicesPage 6

FELT DISC CARD - 1

1M

ANGLE BRACKET - 40

27G

GROMMET CAP - 2

1P

MOLDING

CONNECTOR - 4

17F

METAL PIN - 12

1R

19G

METAL BRACKET - 2

KEYBOARD

HINGE - 2

12H

CORD CLIP - 1

9P

GROMMET - 3

10P

KNOB - 8

33K

RUBBER SLEEVE - 4

2R

14H

HINGE - 2

SMALL DRAWER

FRONT BRACKET - 2

6G

LARGE DRAWER

FRONT BRACKET - 4

10G

DRAWER FRONT

BRACKET - 2

9G

Hardware Identiﬁ cation

å Screws are shown actual size. You may receive extra hardware with your unit.

412902www.sauder.com/services

Page 7

BLACK 1-1/8" PAN HEAD SCREW - 16

9S

GOLD 1" MACHINE SCREW - 4

50S

BLACK 9/16" LARGE HEAD SCREW - 106

1S

BLACK 1-1/4" FLAT HEAD SCREW - 46

7S

SILVER 1-1/4" MACHINE SCREW - 4

35S

18S

BROWN 1" FLAT HEAD SCREW - 12

3S

GOLD 5/16" FLAT HEAD SCREW - 48

SILVER 5/8" FLAT HEAD SCREW - 4

23S

SILVER 9/16" LARGE HEAD SCREW - 2

54S 100S

BLACK 2-3/4" FLAT HEAD SCREW - 3

BLACK 1/2" FLAT HEAD SCREW - 4

11S

30S

BLACK 1-9/16" FLAT HEAD SCREW - 24

BLACK 1-15/16" FLAT HEAD SCREW - 8

113S

Step 1

Look for this icon. It means a

video assembly tip is available at

www.sauder.com/services/tips

å

Assemble your unit on a carpeted ﬂ oor or on the empty

carton to avoid scratching your unit or the ﬂ oor.

å

To begin assembly, push a SAUDER TWIST-LOCK®

FASTENER (7F) into the large holes in the OUTER ENDS (A).

å

Repeat this step for the ENDS (B3 and C3), UPRIGHTS (D2

and E2), BOTTOMS (G2), MODESTY PANEL (H2), and UPPER

BACK MOLDING (MM).

412902 www.sauder.com/servicesPage 8

A

(25 used)

Do not tighten the TWIST-LOCK® FASTENERS in this step.

7F

Scan this QR code or go to this address:

http://qr.sauder.com/?ID=1658

to watch a video on how to assemble your unit.

å

Push eight HIDDEN CAMS (1F) into the BOTTOMS (G2).

Then, insert the metal end of a CAM DOWEL (2F) into

each HIDDEN CAM.

Step 2

412902www.sauder.com/services

Page 9

G2

(8 used)

Arrow

Insert the metal end of the CAM

DOWEL into the HIDDEN CAM.

Arrow

Do not tighten the HIDDEN CAMS in this step.

1F

2F

Step 3

å

NOTE: Before beginning this step, separate the NARROW EXTENSION

SETS (AAA and BBB) from the WIDE EXTENSION SETS (CCC and DDD).

Do not confuse these SETS once they are separated.

å

Separate the NARROW EXTENSION SLIDES (BBB) from the NARROW EXTENSION

RAILS (AAA) as shown in the upper diagram below. Be prepared, the parts are greasy.

å

Fasten the NARROW EXTENSION RAILS (AAA) to the ENDS (B3 and C3) and

UPRIGHTS (D2 and E2). Use sixteen GOLD 5/16" FLAT HEAD SCREWS (3S).

å

NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged

diagram. Then, slide the inner cartridge of the EXTENSION RAIL in to ﬁ nd the other

hole that lines up with the hole in the END and UPRIGHT. Turn a SCREW into this hole.

å

NOTE: The EXTENSION SLIDES will be used later for the DRAWERS.

412902 www.sauder.com/servicesPage 10

C3

B3

D2

E2

AAA

Push the release lever in and pull the SLIDE from the RAIL.

AAABBB

Narrow

Extension

Rails

Open end

Narrow

Extension

Rails

Surface with

TWIST-LOCK®

FASTENERS

Surface with

TWIST-LOCK®

FASTENERS

Surface with

TWIST-LOCK®

FASTENERS

Surface with

TWIST-LOCK®

FASTENERS

GOLD 5/16" FLAT HEAD SCREW

(16 used in this step)

3S

å

Separate the WIDE EXTENSION SLIDES (DDD) from the WIDE EXTENSION RAILS (CCC) as shown in the upper diagram

below. Be prepared, the parts are greasy.

å

Fasten the WIDE EXTENSION RAILS (CCC) to the ENDS (B3 and C3) and UPRIGHTS (D2 and E2). Use twelve GOLD

5/16” FLAT HEAD SCREWS (3S).

å

NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged diagram. Then, slide the inner

cartridge of the EXTENSION RAIL in to ﬁ nd the other holes that line up with the holes in the ENDS and UPRIGHTS. Turn a

SCREW into this hole.

å

NOTE: The EXTENSION SLIDES will be used later for the DRAWERS.

å

Fasten four ANGLE BRACKETS (27G) to the RIGHT END (B3) and RIGHT UPRIGHT (D2). Use four BLACK 9/16" LARGE

HEAD SCREWS (1S).

å

NOTE: Be sure the edges

of the ANGLE BRACKETS

are even with the edges of

the END and UPRIGHT.

Step 4

412902www.sauder.com/services

Page 11

C3

B3

D2

E2

CCC

BLACK 9/16" LARGE HEAD SCREW

(4 used for the ANGLE BRACKETS)

Push the black lever in and pull the SLIDE from the RAIL.

CCCDDD

Wide

Extension

Rails

Wide

Extension

Rails

GOLD 5/16" FLAT HEAD SCREW

(12 used in this step)

Open end

(4 used)

3S

27G

1S

Step 5

å

Fasten the CABINET RAILS (WW and XX) to the other

surfaces of the UPRIGHTS (D2 and E2). Use four GOLD

5/16" FLAT HEAD SCREWS (3S).

å

NOTE: The CABINET RAILS are marked "CABINET

RIGHT" and "CABINET LEFT" for easy identiﬁ cation.

412902 www.sauder.com/servicesPage 12

D2

E2

WW

XX

Surface without

TWIST-LOCK

®

FASTENERS

Surface without

TWIST-LOCK

®

FASTENERS

Roller end

These holes must be here.

Roller end

GOLD 5/16" FLAT HEAD SCREW

(4 used in this step)

3S

å

Tap four MOLDING CONNECTORS (17F) into the notches in

the TOP MOLDINGS (LL and UU) and SIDE MOLDINGS (NN).

Step 6

412902www.sauder.com/services

Page 13

LL

NN

UU

NN

Flat end

Use your hammer to tap the MOLDING CONNECTORS (17F) into the notches in the MOLDINGS.

17F

Step 7

å

Fasten the TOP MOLDINGS (LL and UU) and SIDE

MOLDINGS (NN) to the TOP (F2). Use sixteen BLACK

1-1/4" FLAT HEAD SCREWS (7S).

å

NOTE: Do not overtighten the SCREWS into the TOP.

412902 www.sauder.com/servicesPage 14

LL

NN

UU

NN

F2

Surface with holes

The large holes must be here.

The TOP REAR

MOLDING (LL)

has more holes.

BLACK 1-1/4" FLAT HEAD SCREW

(16 used in this step)

7S

å

Fasten the METAL BRACKETS (19G) to the UPPER

BACK MOLDING (MM). Use two BLACK 9/16" LARGE

HEAD SCREWS (1S).

å

Fasten the UPPER BACK MOLDING (MM) to the TOP

REAR MOLDING (LL) on the TOP (F2). Tighten three

TWIST-LOCK® FASTENERS.

Step 8

412902www.sauder.com/services

Page 15

LL

F2

MM

How to use the SAUDER TWIST-LOCK

®

FASTENER

1. Insert the dowel end of the FASTENER into the

hole of the adjoining part.

NOTE: The dowel end of the FASTENER must

remain fully inserted in the hole of the adjoining

part while locking the FASTENER.

2. Tighten the FASTENER with a Phillips

screwdriver as tight as possible.

Edge and surface with

TWIST-LOCK® FASTENERS

MM

Dowel end

BLACK 9/16" LARGE HEAD SCREW

(2 used in this step)

19G

1S

Step 9

å

Fasten the HALF DISKS (VV) to the PLINTHS (DD). Use

eight BROWN 1" FLAT HEAD SCREWS (18S).

å

Fasten twenty ANGLE BRACKETS (27G) to the

OUTER ENDS (A). Use twenty BLACK 9/16" LARGE

HEAD SCREWS (1S).

å

NOTE: Be sure the edges of the ANGLE BRACKETS are

even with the edges of the OUTER ENDS.

412902 www.sauder.com/servicesPage 16

DD

VV

A

DD

VV

DD

VV

DD

VV

DD

VV

DD

VV

DD

VV

DD

VV

The larger hole

should be facing up.

Surface with

TWIST-LOCK

®

FASTENERS

Surface with

TWIST-LOCK

®

FASTENERS

(20 used)

BROWN 1" FLAT HEAD SCREW

(8 used in this step)

27G

18S

BLACK 9/16" LARGE HEAD SCREW

(20 used for the ANGLE BRACKETS)

1S

å

Fasten the OUTER ENDS (A) to the SIDE

MOLDINGS (NN) on the TOP (F2). Tighten four

TWIST-LOCK® FASTENERS.

Step 10

412902www.sauder.com/services

Page 17

A

NN

F2

NN

Surface with

TWIST-LOCK

®

FASTENERS

Surface without

TWIST-LOCK

®

FASTENERS

Step 11

å

Fasten the PLINTHS (DD) and MOLDINGS (M26) to

the OUTER ENDS (A). Use twenty BLACK 9/16" LARGE

HEAD SCREWS (1S).

412902 www.sauder.com/servicesPage 18

A

DD

VV

The MOLDING (M26) should be

centered over the HALF DISK (VV).

These holes

must be here.

These holes

must be here.

M26

BLACK 9/16" LARGE HEAD SCREW

(20 used for the ANGLE BRACKETS)

1S

Use outer holes.

å

Insert four METAL PINS (1R) into the ENDS (B3 and C3).

å

Fasten the ENDS (B3 and C3) to the TOP (F2). Tighten

four TWIST-LOCK® FASTENERS.

å

NOTE: Be sure the METAL PINS in the ENDS insert into

the holes in the TOP.

Step 12

412902www.sauder.com/services

Page 19

F2

C3

B3

Surface with

TWIST-LOCK

®

FASTENERS

Surface without

TWIST-LOCK

®

FASTENERS

Open end

(4 used)

1R

Step 13

å

Fasten the BOTTOMS (G2) to the OUTER ENDS (A). Tighten

four TWIST-LOCK® FASTENERS.

å

Fasten the BOTTOMS (G2) to the ENDS (B3 and C3). Use

four BLACK 1-15/16" FLAT HEAD SCREWS (113S).

å

Insert four METAL PINS (1R) into the PEDESTAL BACK (J).

å

Insert the METAL PINS (1R) in one end of the PEDESTAL

BACK (J) into the holes in the LEFT END (C3).

412902 www.sauder.com/servicesPage 20

Surface with

TWIST-LOCK

®

FASTENERS

Surface with

TWIST-LOCK

®

FASTENERS

A

J

C3

G2

B3

113S

The large holes must be here.

Unﬁ nished

surface

(4 used)

1R

BLACK 1-15/16" FLAT HEAD SCREW

(4 used in this step)

113S

La page charge ...

Sauder Palladia Collection 412902 Mode d'emploi

Sauder Palladia Collection 412902 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents