Troy Lighting F1218 1 Light 10 inch Gesso White Pendant Ceiling Light Manuel utilisateur

Marque: Troy Lighting

Modèle: F1218 1 Light 10 inch Gesso White Pendant Ceiling Light

Taper: Manuel utilisateur

ENZO

F1218

INSTALLATION INSTRUCTIONS

WARNING/CAUTION

·DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS

COMPLETELY BEFORE STARTING INSTALLATION.

·TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL

APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION AND

MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED

FACTORY TRAINED TECHNICIAN.

·CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF

CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM. WASH

HANDS AFTER USE.

·REMOVE THE FIXTURE, PARTS AND PARTS BAG(S) FROM THE CARTON. BEFORE DISCARDING THE

CARTON, DOUBLE CHECK TO MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE

PRIOR TO INSTALLATION FOR ANY DAMAGE TO THE FIXTURE.

·DIMMING: THE FIXTURE CAN BE CONTROLLED BY A WALL DIMMING DEVICE. ONLY USE

TRIAC/ELECTRONIC DIMMER. MAKE SURE THE CARTON IS MARKED FOR USE WITH LED COMPACT

FLUORESCENT-INCANDESCENT LIGHT SOURCE ONLY. THESE CAN BE PROVIDED BY YOUR LOCAL

ELECTRICAL DISTRIBUTOR, HOME CENTER, OR HARDWARE STORE.

·PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS

www.hvlgroup.com

Questions? We're here to help!

FIXTURE INSTALLATION

1. Attach the MOUNTING PLATE (1) onto the junction box using the MOUNTING SCREWS (2). This fixture is designed to

be mounted on standard round or octagon junction box. The junction box must be securely mounted to the structure of

the building.

2. Remove the SCREW COLLAR (3) from the COLLAR LOOP (4). Fully thread the NIPPLE (5) onto the COLLAR LOOP

(4). Thread the HEX NUTS (6) onto the NIPPLE (5) along with TOOTH WASHER (7). Then thread the NIPPLE (5) unto

the MOUNTING PLATE (1). Adjust the NIPPLE (5) so that the threads of the COLLAR LOOP (4) extends 1/4" beyond

the CANOPY (8). Secure using HEX NUT (6).

3. Open the end link the of the CHAIN (9) and attach to the FIXTURE ASSEMBLY (10) at the desired height. Slide the

SCREW COLLAR (3) and the CANOPY (8) onto the CHAIN (9). Attach the other end of the CHAIN (9) unto the COLLAR

LOOP (4). Feed the wires through the CHAIN (9) , SCREW COLLAR (3), CANOPY (8), COLLAR LOOP (4), NIPPLE (5),

and MOUNTING PLATE (1).

4. Cut off excess wires, and strip the insulation off the end of the leads.

5. Attach the Ground wire (Green) to the ground inside the junction box (Generally green or bare copper wire) or the

GROUND SCREW (11) on the MOUNTING PLATE (1). NEVER CONNECT GROUND WIRE TO "HOT" WIRE!

FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!

6. Connect the fixture's SPT Neutral (SPT WIRE WITH NO WRITINGS) wire lead to the neutral (Generally white) wire in the

outlet box. Fasten the wires together with an approved fastener (WIRE NUT) (12). Starting 1" below the fastener, tightly

wrap the connection with electrical tape so that the connections seals the end of the fastener. MAKE SURE THERE ARE

NO EXPOSED WIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT!

7. Connect the fixture's SPT hot (SPT WITH WRITNGS) wire lead to the hot (Generally black) wire in the junction box.

Fasten the joined wires same as previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO

FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!

8. Push the wires back into the junction box. Lift up the CANOPY (8) up to the ceiling, and screw the SCREW COLLAR (3)

onto the COLLAR LOOP (4).

9. Screw the BULB (13) up into the SOCKET of the fixture.THIS FIXTURE IS RATED FOR 75 WATT TYPE A LAMP. DO

NOT EXCEED THE RECOMMENDED WATTAGE!

10. Untighten the THREADED COLLAR (15) from FITTER (16) allowing the glass over to make space for the GLASS (14).

Place the GLASS (14) beyond the glass holder. (NOTE: Please handle the GLASS (14) with care when putting to the

glass holder). Tighten back the THREADED COLLAR (15) to FITTER (16) just enough to hold the GLASS (14).

11. Restore power to the outlet at the breaker or fuse box.

ITEM DESCRIPTION PART NUMBER

1MOUNTING PLATE HDW-F1213

2MOUNTING SCREW HDW-F1213

3SCREW COLLAR HDW-F1213

4COLLAR LOOP CAS-F1213

5NIPPLE HDW-F1213

6HEX NUT HDW-F1213

7TOOTH WASHER HDW-F1213

8CANOPY CAS-F1213

9CHAIN CHN-F1213

10 FIXTURE ASSEMBLY FAS-F1218

11 GROUND SCREW HDW-F1213

12 WIRE NUT HDW-F1213

13 BULB NOT INCLUDED

14 GLASS GLS-F1218

15 THREADED COLLAR HRD-F1213

16 FITTER FIT-F1218