Cameo CLCONTROL6 Manuel utilisateur

6-CHANNEL DMX CONTROLLER

CLCONTROL6

USER´S MANUAL

BEDIENUNGSANLEITUNG

MANUEL D´UTILISATION

MANUAL DE USUARIO

INSTRUKCJA OBSŁUGI

MANUALE D‘USO

Introduction

The Cameo CLCONTROL6 is an especially compact DMX controller with 6 channels that is perfect for controlling

small lighting systems. It can be mounted in many ways and of course can also be used as a freestanding unit; it

is extremely easy to operate.

The CLCONTROL6 has 6 smoothly shifting faders for the individual DMX channels and a master fader. It can

be powered using the included external power adapter or batteries and thus is universally useable for manual

control of DMX systems. A 3-pole XLR socket is used as the DMX output; a red LED serves as a power indicator.

This straightforward lightweight impresses with clear functionality and high user friendliness.

2 3

ENGLISHDEUTSCHFRANCAIS

FRANCAISFRANCAIS FRANCAISFRANCAIS

ESpAñoLpoLSKIITALIANo

Thank you for choosing Cameo Lights!

We have designed this product to give you reliable operation over many years.

Please, take a few moments to read these instructions carefully, as we want you to enjoy your new Cameo Lights

products quickly and to the fullest.

Further information about Cameo Lights check our website WWW.CAMEOLIGHT.COM

6-CHANNEL DMX CONTROLLER

CLCONTROL6

2 3

ITALIANOPOLSKIESPAÑOL

FRANCAISFRANCAIS FRANCAISFRANCAIS

FRANCAISDEUTSCHENGLISH

4 5

ENGLISHDEUTSCHFRANCAIS

FRANCAISFRANCAIS FRANCAISFRANCAIS

ESpAñoLpoLSKIITALIANo

PREVENTIVE MEASURES:

1. Please read these instructions carefully.

2. Keep all information and instructions in a safe place.

3. Follow the instructions.

4. Observe all safety warnings. Never remove safety warnings or other information from the equipment.

5. Use the equipment only in the intended manner and for the intended purpose.

6. Use only sufﬁciently stable and compatible stands and/or mounts (for ﬁxed installations). Make certain that wall

mounts are properly installed and secured. Make certain that the equipment is installed securely and cannot fall down.

7. During installation, observ e the applicable safety regulations for your country.

8. Never install and operate the equipment near radiators, heat registers, ovens or other sources of heat. Make

certain that the equipment is always installed so that is cooled sufﬁciently and cannot overheat.

9. Never place sources of ignition, e.g., burning candles, on the equipment.

10. Ventilation slits must not be blocked.

11. Do not use this equipment in the immediate vicinity of water (does not apply to special outdoor equipment -

in this case, observe the special instructions noted below. Do not expose this equipment to ﬂammable materials,

ﬂuids or gases.

12. Make certain that dripping or splashed water cannot enter the equipment. Do not place containers ﬁlled with

liquids, such as vases or drinking vessels, on the equipment.

13. Make certain that objects cannot fall into the device.

14. Use this equipment only with the accessories recommended and intended by the manufacturer.

15. Do not open or modify this equipment.

16. After connecting the equipment, check all cables in order to prevent damage or accidents, e.g., due to

tripping hazards.

17. During transport, make certain that the equipment cannot fall down and possibly cause property damage and

personal injuries.

18. If your equipment is no longer functioning properly, if ﬂuids or objects have gotten inside the equipment or

if it has been damaged in anot her way, switch it off immediately and unplug it from the mains outlet (if it is a

powered device). This equipment may only be repaired by authorized, qualiﬁed personnel.

19. Clean the equipment using a dry cloth.

20. Comply with all applicable disposal laws in your country. During disposal of packaging, please separate

plastic and paper/cardboard.

21. Plastic bags must be kept out of reach of children.

FOR EQUIPMENT THAT CONNECTS TO THE POWER MAINS:

22. CAUTION: If the power cord of the device is equipped with an earthing contact, then it must be connected to

an outlet with a protective ground. Never deactivate the protective ground of a power cord.

23. If the equipment has been exposed to strong ﬂuctuations in temperature (for example, after transport), do

not switch it on immediately. Moisture and condensation could damage the equipment. Do not switch on the

equipment until it has reached room temperature.

24. Before connecting the equipment to the power outlet, ﬁrst verify that the mains voltage and frequency match

the values speciﬁed on the equipment. If the equipment has a voltage selection switch, connect the equipment to

the power outlet only if the equipment values and the mains power values match. If the included power cord or

power adapter does not ﬁt in your wall outlet, contact your electrician.

25. Do not step on the power cord. Make certain that the power cable does not become kinked, especially at the

mains outlet and/or power adapter and the equipment connector.

26. When connecting the equipment, make certain that the power cord or power adapter is always freely

accessible. Always disconnect the equipment from the power supply if the equipment is not in use or if you want

4 5

ITALIANOPOLSKIESPAÑOL

FRANCAISFRANCAIS FRANCAISFRANCAIS

FRANCAISDEUTSCHENGLISH

SAFETY:

to clean the equipment. Always unplug the power cord and power adapter from the power outlet at the plug or

adapter and not by pulling on the cord. Never touch the power cord and power adapter with wet hands.

27. Whenever possible, avoid switching the equipment on and off in quick succession because otherwise this

can shorten the useful life of the equipment.

28. IMPORTANT INFORMATION: Replace fuses only with fuses of the same type and rating. If a fuse blows repea-

tedly, please contact an authorised service centre.

29. To disconnect the equipment from the power mains completely, unplug the power cord or power adapter

from the power outlet.

30. If your device is equipped with a Volex power connector, the mating Volex equipment connector must be

unlocked before it can be removed. However, this also means that the equipment can slide and fall down if

the power cable is pulled, which can lead to personal injuries and/or other damage. For this reason, always be

careful when laying cables.

31. Unplug the power cord and power adapter from the power outlet if there is a risk of a lightning strike or

before extended periods of disuse.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

Never remove the cover, because otherwise there may be a risk of electric shock. There are no user serviceable

parts inside. Have repairs carried out only by qualiﬁed service personnel.

The lightning ﬂash with arrowhead symbol within an equilateral triangle is intended to alert the user

to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of

sufﬁcient magnitude to constitute a risk of electrical shock.

The exclamation mark within an equilateral triangle is intended to alert the user to the presence of

important operating and maintenance instructions.

CAUTION – HIGH VOLUME LEVELS WITH AUDIO PRODUCTS!

This equipment is intended for professional use. Therefore, commercial use of this equipment is subject to the

respectively applicable national accident prevention rules and regulations. As a manufacturer, Adam Hall is

obligated to notify you formally about the existence of potential health risks.

Hearing damage due to high volume and prolonged exposure: When in use, this product is capable of producing

high sound-pressure levels (SPL) that can lead to irreversible hearing damage in performers, employees, and

audience members. For this reason, avoid prolonged exposure to volumes in excess of 90 dB.

CAUTION! IMPORTANT INFORMATION ABOUT LIGHTING PRODUCTS

1. Do not look into the beam from a distance of less than 40 cm.

2. Do not stare into the beam for extended periods at short-to-medium distances.

3. Do not view the beam directly with optical instruments such as magniﬁers.

INTRODUCTION:

FEATURES:

6-CHANNEL DMX CONTROLLER

(CLCONTROL6)

• 6 DMX channels

• 6 smoothly shifting faders

• 1 separate master fader

• light and compact

• operation as a tabletop console

• installable

• ready for wall mounting

• power supply via included power adapter or 9V battery

6 7

ENGLISHDEUTSCHFRANCAIS

FRANCAISFRANCAIS FRANCAISFRANCAIS

ESpAñoLpoLSKIITALIANo

OPERATION:

The CLCONTROL6 is a 6-channel DMX controller with which one or more DMX spotlights in a group with the

same DMX start address (001) can be operated in 6-channel mode with the same DMX signal. If the DMX

spotlights have a 3-channel mode, then two groups of spotlights can be controlled separately (group 1 = DMX

start address 001, group 2 = DMX start address 004); if they have a 2-channel mode, then three groups of

spotlights can be controlled independently (group 1 = DMX start address 001, group 2 = DMX start address 003,

and group 3 = DMX start address 005).

EXAMPLE OF USE:

Controlling 3 x 2 LED lights in 2-channel mode

DMX start address: 001

LED group 1

Controller channel: 1

and 2

DMX out / DMX in

DMX out / DMX inDMX out / DMX in

DMX in

DMX start address: 003

LED group 2

Controller channel: 3 and 4

DMX start address: 005

LED group 3

Controller channel: 5 and 6

DMX out

6 7

ITALIANOPOLSKIESPAÑOL

FRANCAISFRANCAIS FRANCAISFRANCAIS

FRANCAISDEUTSCHENGLISH

CONTROLS AND DISPLAY:

1

CHANNEL FADERS 1 TO 6

When the faders are all the way down, the lowest DMX value (0%) is output; when the faders are all the way

up, the highest DMX value (100%) is output.

2

MASTER FADER

Channels 1 to 6 are ganged on this fader, which means that the master fader controls the output of all 6 DMX

channels.

3

POWER LED

Lights up when the DMX controller is on, the low-voltage connector of the power adapter is inserted in the

equipment correctly, and the power adapter is connected to the power mains. The LED also lights up during

battery-powered operation.

4

MOUNTING HOLES

The 4 mounting holes can be used to fasten the DMX controller securely during installation (installed dimen-

sions W x H x D 148 x 128 x 52 mm).

8 9

ENGLISHDEUTSCHFRANCAIS

FRANCAISFRANCAIS FRANCAISFRANCAIS

ESpAñoLpoLSKIITALIANo

1

2

3

4

REAR PANEL:

1

LOW-VOLTAGE SOCKET

Connector for power adapter. Please use only the original power adapter supplied with the equipment.

Note: When the equipment is operated with the power adapter, the battery power supply is automatically

interrupted.

2

ON / OFF SWITCH

Always turn the equipment off after use.

3

DMX OUTPUT SOCKET

Use a DMX cable to connect the female 3-pole XLR socket of the DMX controller to the DMX input of your

spotlight.

8 9

ITALIANOPOLSKIESPAÑOL

FRANCAISFRANCAIS FRANCAISFRANCAIS

FRANCAISDEUTSCHENGLISH

1 2 3

BOTTOM:

1

BATTERY COMPARTMENT

For battery-powered operation, a 9V battery must be inserted and connected. Remove the battery before

extended periods of disuse and operation only with the power adapter.

2

MOUNTING HOLES FOR WALL MOUNTING

IMPORTANT: The mounting screws must not protrude more than 5 mm into the housing. The spacing bet-

ween holes is 110 mm.

10 11

ENGLISHDEUTSCHFRANCAIS

FRANCAISFRANCAIS FRANCAISFRANCAIS

ESpAñoLpoLSKIITALIANo

1

2 2

DMX CONNECTION:

DMX-512

DMX (Digital Multiplex) is the designation for a universal transmission protocol for communications between

corresponding devices and controllers. A DMX controller sends DMX data to the connected DMX equipment.

The DMX data transmission always takes place as a serial data stream that is passed from one connected

device to the next via the "DMX IN" and "DMX OUT" connectors (XLR plug-type connectors) found on every

DMX-compatible device. (Most controllers only have a DMX output.)

DMX CONNECTION:

DMX is the common "language" via which an extremely wide range of types and models of equipment by

various manufacturers can be connected to one another and controlled via a central controller, provided

that all devices and the controller are DMX-compatible. For optimal data transmission, it is necessary to

keep the connecting cables between the individual devices as short as possible. The order in which the

devices are integrated in the DMX network has no influence on the addresses. For example, the device

with the DMX address 1 can be at any position in the (serial) DMX chain: at the beginning, at the end or

somewhere in the middle. If the DMX address 1 is assigned to a device, the controller "knows" that it

should send all data allocated to address 1 to this device regardless of its position in the DMX network.

An extensive selection of suitable cables can be found in the Adam Hall 3 STAR, 4 STAR, and 5 STAR

product lines.

SERIAL CONNECTION OF MULTIPLE SPOTLIGHTS

1. Connect the male 3-pole XLR plug of the DMX cable to the DMX output (female 3-pole socket) of the first

spotlight or other DMX device.

2. Connect the female 3-pole XLR plug of the DMX cable connected to the first spotlight with the DMX input

(male 3-pole socket) of the next DMX device. In the same manner, connect the DMX output of this device to

the DMX input of the next device, etc..

Please note that, as a rule, DMX devices are connected in series and the connections cannot be split

without active splitters.

10 11

ITALIANOPOLSKIESPAÑOL

FRANCAISFRANCAIS FRANCAISFRANCAIS

FRANCAISDEUTSCHENGLISH

DMX CABLE:

NOTE:

• When fabricating your own cables, always observe the illustrations on this page. Never connect the shielding

of the cable with the ground contact of the plug, and make certain that the shielding does not come into contact

with the XLR plug housing. If the shielding is connected to ground, this can lead to short-circuiting and system

errors.

PLEASE NOTE: LINE TERMINATION:

• With extended cable runs, the last device in the chain may require a terminating resistor in order to avoid

system errors.

This is achieved with a cable termination module (Product No. K3DMXT3).

• Some manufacturers use 5-pole versions for data transmission instead of 3-pole XLR plugs. However, devices

with 5-pole XLR connectors can be integrated in a DMX network with 3-pole XLR connectors. In this case, a

suitable cable adapter is required. The following illustration shows the correct pin-out of the corresponding

plugs.

12 13

ENGLISHDEUTSCHFRANCAIS

FRANCAISFRANCAIS FRANCAISFRANCAIS

ESpAñoLpoLSKIITALIANo

Die Verwendung eines Abschlusswiderstands

(Terminierung) reduziert Interferenzen und

andere Probleme bei der Signalübertragung.

Es ist immer ratsam, ein DMX-Abschlussmodul

(Widerstand 120 Ohm, 1/4 W) zwischen Pol 2

(DMX-) und Pol 3 (DMX+) des letzten Geräts in

der Kette einzufügen.

Übliche Verbindung

DMX-512-Ausgang

3-Pol-XLR

DMX-512-Eingang

3-Pol-XLR

5-Pol-XLR (Buchse)

Pol 1: Erde

(Abschirmung)

Pol 2: Signal (-)

Pol 3: Signal (+)

Pol 4: nicht belegt

Pol 5: nicht belegt

5-Pol-XLR (Buchse)

Pol 1: Erde

(Abschirmung)

Pol 2: Signal (-)

Pol 3: Signal (+)

Pol 4: nicht belegt

Pol 5: nicht belegt

3-Pol-XLR (Buchse)

Pol 1: Erde

(Abschirmung)

Pol 2: Signal (-)

Pol 3: Signal (+)

3-Pol-XLR (Buchse)

Pol 1: Erde

(Abschirmung)

Pol 2: Signal (-)

Pol 3: Signal (+)

Model name: CLCONTROL6

Product type: DMX mixer

Type: DMX 512 protocol

Number of DMX channels: 6

DMX output: 3-pole XLR female

Controls: 6x channel faders, master fader

Indicators: Power LED

Power supply: 9 - 12 V DC

Dimensions (W x H x D): 167 x 56 x 134 mm

Weight: 0.7 kg

Other features: Power adapter included

12 13

ITALIANOPOLSKIESPAÑOL

FRANCAISFRANCAIS FRANCAISFRANCAIS

FRANCAISDEUTSCHENGLISH

SPECIFICATIONS:

14 15

ENGLISHDEUTSCHFRANCAIS

FRANCAISFRANCAIS FRANCAISFRANCAIS

ESpAñoLpoLSKIITALIANo

MANUFACTURER‘S WARRANTY

This warranty covers the Adam Hall, LD Systems, Defender, Palmer, and Cameo brands.

It applies to all products distributed by Adam Hall.

This warranty declaration does not affect the statutory warranty claims against the manufacturer, but expands

them with additional warranty claims vis-a-vis Adam Hall.

Adam Hall warrants that the Adam Hall product that you have purchased from Adam Hall or from an Adam Hall

authorized reseller is free from defects in materials or workmanship under normal use for a period of 2 or 5 years

(please inquire on a product-by-product basis) from the date of purchase.

The warranty period begins on the date on which the product was purchased, proof of which must be produced

(through presentation of the invoice or the delivery note with the date of purchase) in the event of a warranty claim.

Should products of the brands named above be in need of repair within the limited warranty period, you are entitled

to warranty service according to the terms and conditions stated here.

During the Limited Warranty Period, Adam Hall will repair or replace the defective component parts or the product.

In the event of repair or replacement during the Limited Warranty Period, the replaced original parts and/or pro-

ducts become property of Adam Hall.

In the unlikely event that the product which you purchased has a recurring failure, Adam Hall has the right, at its

discretion, to replace the defective product with another product, provided that the new product is at least equi-

valent to the product being replaced with regard to the technical speciﬁcations.

Adam Hall does not warrant that the operation of this product will be uninterrupted or error-free. Adam Hall is not

responsible for damage that occurs as a result of your failure to follow the instructions included with the Adam Hall

branded product. The manufacturer‘s warranty does not cover – expendable parts (e. g., rechargeable batteries)

- products from which the serial number has been removed or with a serial number that has been damaged as a

result of an accident - damage due to improper use, user error or other external reasons

- damage to devices operated outside the usage parameters stated in the documentation included with the product

- damage due to the use of replacement parts not manufactured, sold or recommended by Adam Hall,

- damage due to modiﬁcation or servicing by anyone other than Adam Hall.

These terms and conditions constitute the complete and exclusive warranty agreement between you and Adam

Hall regarding the Adam Hall branded product you have purchased.

MANUFACTURER´S DECLARATIONS:

14 15

ITALIANOPOLSKIESPAÑOL

FRANCAISFRANCAIS FRANCAISFRANCAIS

FRANCAISDEUTSCHENGLISH

MANUFACTURER´S DECLARATIONS:

LIMITATION OF LIABILITY

If your Adam Hall branded hardware product fails to work as warranted above, your sole and exclusive remedy

shall be repair or replacement. Adam Halls’ maximum liability under this limited warranty is expressly limited to

the lesser of the price you have paid for the product or the cost of repair or replacement of any components that

malfunction under conditions of normal use.

Adam Hall is not liable for any damages caused by the product or the failure of the product, including any lost

proﬁts or savings or special, incidental, or consequential damages. Adam Hall is not liable for any claim made by

a third party or made by you for a third party.

This limitation of liability applies whether damages are sought, or claims are made, under this Limited Warranty

or as a tort claim (including negligence and strict product liability), a contract claim, or any other claim, and

cannot be rescinded or changed by anyone. This limitation of liability will be effective even if you have advised

Adam Hall or an authorized representative of Adam Hall of the possibility of any such damages, but not, however,

in the event of claims for damages in connection with personal injuries.

This manufacturer‘s warranty grants you speciﬁc rights; depending on jurisdiction (nation or state), you may be

be entitled to additional claims. You are advised to consult applicable state or national laws for a full determina-

tion of your rights.

REQUESTING WARRANTY SERVICE

To request warranty service for the product, contact Adam Hall or the Adam Hall authorized reseller from which

you purchased the product.

EC DECLARATION OF CONFORMITY

The equipment marketed by Adam Hall complies (where applicable) with the essential requirements and other

relevant specications of Directives 1999/5/EC (R&TTE), 2004/108/EC (EMC) und 2006/95/EC (LVD). Additional

information can be found at www.adamhall.com.

16 17

ENGLISHDEUTSCHFRANCAIS

FRANCAISFRANCAIS FRANCAISFRANCAIS

ESpAñoLpoLSKIITALIANo

MANUFACTURER´S DECLARATIONS:

PROPER DISPOSAL OF THIS PRODUCT

(Valid in the European Union and other European countries with waste separation)

This symbol on the product, or the documents accompanying the product, indicates that this appliance may not

be treated as household waste. This is to avoid environmental damage or personal injury due to uncontrolled

waste disposal. Please dispose of this product separately from other waste and have it recycled to promote

sustainable economic activity.

Household users should contact either the retailer where they purchased this product, or their local government

ofﬁce, for details on where and how they can recycle this item in an environmentally friendly manner.

Business users should contact their supplier and check the terms and conditions of the purchase contract. This

product should not be mixed with other commercial wastes for disposal .

ENVIRONMENTAL PROTECTION AND ENERGY CONSERVATION

Energy conservation is an active contribution to environmental protection. Please turn off all unneeded electrical

devices. To prevent unneeded devices from consuming power in standby mode, disconnect the mains plug.

to modiﬁcations. The photocopying, the translation, and all other forms of copying of fragments or of the integrlity

of this user’s manual is prohibited.

16 17

ITALIANOPOLSKIESPAÑOL

FRANCAISFRANCAIS FRANCAISFRANCAIS

FRANCAISDEUTSCHENGLISH

Einleitung

Der Cameo CLCONTROL6 ist ein besonders kompakter DMX-Controller mit 6 Kanälen, der sich perfekt zur

Steuerung kleiner Lichtanlagen eignet. Er läßt sich vielfältig montieren und kann selbstverständlich auch

freistehend genutzt werden, die Bedienung ist äußerst einfach.

Der CLCONTROL6 besitzt 6 leichtgängige Fader für die individuellen DMX-Kanäle und einen Masterfader. Er

kann über das mitgelieferte externe Netzteil oder Batterie betrieben werden und ist so universell zur manuellen

Regelung von DMX-gesteuerten Lichtanlagen einsetzbar. Eine 3-polige XLR-Buchse dient als DMX-Ausgang, eine

rote LED zeigt die Stromversorgung an. Das schnörkellose Leichtgewicht überzeugt durch seine klare, übersicht-

liche Funktion und hohe Benutzerfreundlichkeit.

18 19

ENGLISHDEUTSCHFRANCAIS

FRANCAISFRANCAIS FRANCAISFRANCAIS

ESpAñoLpoLSKIITALIANo

Wir freuen uns, dass Sie sich für ein Produkt von Cameo Light entschieden haben!

Dieses Gerät wurde unter hohen Qualitätsanforderungen entwickelt und gefertigt, um viele Jahre einen

reibungslosen Betrieb zu gewährleisten.

Bitte lesen Sie diese Bedienungsanleitung sorgfältig, damit Sie Ihren neuen Scheinwerfer von Cameo Light

schnell optimal einsetzen können.

Weitere Informationen über Cameo Light erhalten Sie auf unserer Website WWW.CAMEOLIGHT.COM.

6-KANAL DMX-CONTROLLER

CLCONTROL6

18 19

ITALIANOPOLSKIESPAÑOL

FRANCAISFRANCAIS FRANCAISFRANCAIS

FRANCAISDEUTSCHENGLISH

1. Lesen Sie diese Anleitung bitte sorgfältig durch.

2. Bewahren Sie alle Informationen und Anleitungen an einem sicheren Ort auf.

3. Befolgen Sie die Anweisungen.

4. Beachten Sie alle Warnhinweise. Entfernen Sie keine Sicherheitshinweise oder andere Informationen vom Gerät.

5. Verwenden Sie das Gerät nur in der vorgesehenen Art und Weise.

6. Verwenden Sie ausschließlich stabile und passende Stative bzw. Befestigungen (bei Festinstallationen). Stellen

Sie sicher, dass Wandhalterungen ordnungsgemäß installiert und gesichert sind. Stellen Sie sicher, dass das

Gerät sicher installiert ist und nicht herunterfallen kann.

7. Beachten Sie bei der Installation die für Ihr Land geltenden Sicherheitsvorschriften.

8. Installieren und betreiben Sie das Gerät nicht in der Nähe von Heizkörpern, Wärmespeichern, Öfen oder

sonstigen Wärmequellen. Sorgen Sie dafür, dass das Gerät immer so installiert ist, dass es ausreichend gekühlt

wird und nicht überhitzen kann.

9. Platzieren Sie keine Zündquellen wie z.B. brennende Kerzen auf dem Gerät.

10. Lüftungsschlitze dürfen nicht blockiert werden.

11. Betreiben Sie das Gerät nicht in unmittelbarer Nähe von Wasser (gilt nicht für spezielle Outdoor Geräte -

beachten Sie in diesem Fall bitte die im Folgenden vermerkten Sonderhinweise). Bringen Sie das Gerät nicht mit

brennbaren Materialien, Flüssigkeiten oder Gasen in Berührung.

12. Sorgen Sie dafür, dass kein Tropf- oder Spritzwasser in das Gerät eindringen kann. Stellen Sie keine mit

Flüssigkeit gefüllten Behältnisse wie Vasen oder Trinkgefäße auf das Gerät.

13. Sorgen Sie dafür, dass keine Gegenstände in das Gerät fallen können.

14. Betreiben Sie das Gerät nur mit dem vom Hersteller empfohlenen und vorgesehenen Zubehör.

15. Öffnen Sie das Gerät nicht und verändern Sie es nicht.

16. Überprüfen Sie nach dem Anschluss des Geräts alle Kabelwege, um Schäden oder Unfälle, z. B. durch

Stolperfallen zu vermeiden.

17. Achten Sie beim Transport darauf, dass das Gerät nicht herunterfallen und dabei möglicherweise Sach- und

Personenschäden verursachen kann.

18. Wenn Ihr Gerät nicht mehr ordnungsgemäß funktioniert, Flüssigkeiten oder Gegenstände in das Geräteinnere

gelangt sind, oder das Gerät anderweitig beschädigt wurde, schalten Sie es sofort aus und trennen es von der

Netzsteckdose (sofern es sich um ein aktives Gerät handelt). Dieses Gerät darf nur von autorisiertem Fachperso-

nal repariert werden.

19. Verwenden Sie zur Reinigung des Geräts ein trockenes Tuch.

20. Beachten Sie alle in Ihrem Land geltenden Entsorgungsgesetze. Trennen Sie bei der Entsorgung der Verpa-

ckung bitte Kunststoff und Papier bzw. Kartonagen voneinander.

21. Kunststoffbeutel müssen außer Reichweite von Kindern aufbewahrt werden.

BEI GERÄTEN MIT NETZANSCHLUSS:

22. ACHTUNG: Wenn das Netzkabel des Geräts mit einem Schutzkontakt ausgestattet ist, muss es an einer

Steckdose mit Schutzleiter angeschlossen werden. Deaktivieren Sie niemals den Schutzleiter eines Netzkabels.

23. Schalten Sie das Gerät nicht sofort ein, wenn es starken Temperaturschwankungen ausgesetzt war (bei-

spielsweise nach dem Transport). Feuchtigkeit und Kondensat könnten das Gerät beschädigen. Schalten Sie das

Gerät erst ein, wenn es Zimmertemperatur erreicht hat.

24. Bevor Sie das Gerät an die Steckdose anschließen, prüfen Sie zuerst, ob die Spannung und die Frequenz

des Stromnetzes mit den auf dem Gerät angegebenen Werten übereinstimmen. Verfügt das Gerät über einen

Spannungswahlschalter, schließen Sie das Gerät nur an die Steckdose an, wenn die Gerätewerte mit den Werten

des Stromnetzes übereinstimmen. Wenn das mitgelieferte Netzkabel bzw. der mitgelieferte Netzadapter nicht in

Ihre Netzsteckdose passt, wenden Sie sich an Ihren Elektriker.

20 21

ENGLISHDEUTSCHFRANCAIS

FRANCAISFRANCAIS FRANCAISFRANCAIS

ESpAñoLpoLSKIITALIANo

SICHERHEITSHINWEISE:

La page charge ...

Cameo CLCONTROL6 Manuel utilisateur

Ce manuel convient également à

Cameo CLCONTROL6 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents