Briggs & Stratton 030712-00 Manuel utilisateur

Marque: Briggs & Stratton

Modèle: 030712-00

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

Ce manuel convient également à

030712

Not for

Reproduction

Manual No. 80023475 Revision A

Outdoor Portable Generator

Operator’s Manual

Model Number _____________________________

Revision __________________________________

Serial Number ______________________________

Date Purchased ____________________________

800-743-4115

BRIGGSandSTRATTON.COM

Not for

Reproduction

2 BRIGGSandSTRATTON.COM

Equipment Description

Table of Contents

Equipment Description.........................2

Features and Controls .........................5

Operation....................................7

Maintenance ................................12

Storage ....................................15

Troubleshooting/Specifications .................16

Warranty ...................................18

To ensure prompt and complete warranty coverage, register

your product online at www.onlineproductregistration.com.

Symbols and Meanings

Signal Meaning

DANGER

Indicates a hazard which, if not avoided, will

result in death or serious injury.

WARNING

Indicates a hazard which, if not avoided, could

result in death or serious injury.

CAUTION

Indicates a hazard which, if not avoided, could

result in minor or moderate injury.

NOTICE

Indicates information considered important, but

not hazard-related.

Symbol Name Explanation

Safety Alert

Symbol

Indicates a potential personal injury

hazard.

Operator’s

Manual

Failure to follow warnings,

instructions and operator’s manual

could result in death or serious

injury.

Toxic Fumes

Engine exhaust contains carbon

monoxide, a poisonous gas that

could kill you in minutes. You

cannot smell it or see it.

Fire

Fuel and its vapors are extremely

flammable which could cause

burns or fire resulting in death or

serious injury.

Engine exhaust could cause fire

resulting in death or serious injury.

Electric

Shock

Generator could cause electrical

shock resulting in death or serious

injury.

Hot Surface

Muffler could cause burns or

resulting in serious injury.

WARNING! The engine exhaust from this product

contains chemicals known to the State of California to

cause cancer, birth defects, or other reproductive harm.

WARNING! Certain components in this product and

related accessories contain chemicals known to the

State of California to cause cancer, birth defects or

other reproductive harm. Wash hands after handling.

Equipment Description

Read this manual carefully and become familiar

with your outdoor generator. Know its applications,

its limitations, and any hazards involved. Save

these instructions for future reference.

The outdoor generator is an engine-driven, revolving field,

alternating current (AC) generator equipped with a voltage

regulator. The generator is designed to supply electrical power

for operating compatible electrical lighting, appliances, tools

and motor loads. The voltage regulator within the generator is

designed to automatically maintain output voltage level.

The portable generator produces power that can be used for

outdoor items using the extension cords provided or for first

time temporary home power restoration. Before your next home

power outage, install a listed transfer switch. A transfer switch is

a separate device installed by a licensed electrician that allows

the portable generator to be cord connected, using the locking

receptacle, directly into your home’s electrical system. Extension

cords connected to the portable generator’s control panel are

not intended to be a long term solution when connected to items

inside your home.

Every effort has been made to ensure that the information in this

manual is both accurate and current. However, the manufacturer

reserves the right to change, alter or otherwise improve the

generator and this documentation at any time without prior notice.

NOTICE If you have questions about intended use, contact an

authorized service dealer. This equipment is designed to be used

with Briggs & Stratton authorized parts only.

This spark ignition system complies with the Canadian

standard ICES-002.

System Ground

The generator has a system ground that connects the generator

frame components to the ground terminals on the AC output

receptacles. The system ground is connected to the AC neutral

wire (the neutral is bonded to the generator frame).

Special Requirements

There may be Federal or State regulations, local codes, or

ordinances that apply to the intended use of the generator.

Please consult a qualified electrician,

electrical inspector, or

the local agency having jurisdiction.

This generator is not intended to be used at a construction

site or similar activity as defined by NFPA 70-2014 (NEC)

section 590.6.

Not for

Reproduction

Equipment Description

To Temporarily Restore Power

Using Extension Cords

1. Only use cords marked for outdoor use rated for your

loads.

To Temporarily provide power

using extension cords

Total

Amperage

Minimum Guage, Outdoor Rated

Up to 50 FT (15 M) Up to 100 FT (30 M)

Up to 13A

Up to 15A

Up to 20A

2. Follow cord safety instructions.

3. Extension cords running directly into the home

increase your risk of carbon monoxide poisoning

through openings. Install carbon monoxide alarm(s).

4. Before your next home power outage, install a listed*

transfer switch.

To Restore Home Power Using a Listed

Transfer Switch

Connections to your home’s electrical system must use a

listed transfer switch installed by a licensed electrician. The

connection must isolate the generator power from the utility

power and comply with all applicable laws and electrical

codes. Power your home with a 20 Amp transfer switch

system.

120/240V

Outlet

—

Transfer

Switch

Typical Indoor Items

120V

OUTLET

* Certified by a Nationally Recognized Testing Laboratory

that the product complies to appropriate product safety test

standards.

Not for

Reproduction

4 BRIGGSandSTRATTON.COM

Equipment Description

Air Cleaner — Filters engine intake air.

Choke Lever — Used when starting a cold engine.

Engine Identification — Provides model, type and code of engine.

Fuel Cap — Add unleaded fuel here.

Fuel Valve — Used to turn fuel supply on and off to engine.

Grounding Fastener — Consult your local agency having

jurisdiction for grounding requirements in your area.

Identification Label — Provides model and serial number of

generator.

Oil Drain Plug — Drain engine oil here.

Oil Fill Cap/Dipstick — Check and add engine oil here.

Recoil Starter — Used to start the engine manually.

Spark Arrester Muffler — Exhaust muffler lowers engine noise and

is equipped with a spark arrester screen.

Engine Identification

Oil Fill Cap/Dipstick

Oil Drain Plug

Fuel Cap

Grounding Fastener

Choke Lever

Spark Arrester Muffler

Air Cleaner

Identification Label

Fuel Valve

Recoil Starter

Not for

Reproduction

Features and Controls

120 Volt AC, 20 Amp, GFCI Duplex Receptacle

— Used to supply 120 Volt AC, single phase, 60

Hz power for electrical lighting, appliance, tool and

motor loads.

120/240 Volt AC, 20 Amp Locking Receptacle —

Used to supply 120 / 240 Volt AC, single phase, 60

Hz power for electrical lighting, appliance, tool and

motor loads.

Engine Switch — Set this switch to on (I) before

starting engine. Set switch to off (0) to shut off

engine.

Low Oil Shutdown — This unit is equipped with

a low oil protection device. Oil must be at proper

level for engine to run. If the engine oil drops below

a preset level, an oil switch will stop the engine.

Check oil level with dipstick.

Main Breaker — The receptacles are provided with

a 15 Amp rocker switch main circuit breaker to

protect the generator against electrical overload.

Main Breaker

120/240 Volt AC, 20 Amp

Locking Receptacle

120 Volt AC, 20 Amp

GFCI Duplex Receptacle

Low Oil Shutdown

Compare the illustrations with your generator to familiarize yourself with the locations of various controls

and product warnings.

Engine Switch

Not for

Reproduction

6 BRIGGSandSTRATTON.COM

Features and Controls

Muffler

Point away

from home

Read and follow

Operating Instructions

before running or

servicing engine.

Gasoline is flammable.

Allow engine to cool

at least 2 minutes

before refueling.

Engines emit carbon

monoxide that can

kill you. Operate

only outdoors.

Muffler area

temperature may

exceed 150°F (65°C).

Do not touch hot parts.

Lire et suivre les instructions

d´utilisation avant de démarrer

ou effectuer l´entretien du moteur.

L´essence est inflammable.

Laisser refroidir le moteur

pendant au moins 2 minutes

avant de faire le plein.

Autour du silencieux, la

température peut dépasser

150°F (65°C). Ne pas toucher

des pièces chaudes.

WARNING

AVERTISSEMENT

DANGER

Les moteurs émettent du monoxyde

de carbone pouvant vous tuer.

Ne faire fonctionner qu’à l’extérieur.

Not for

Reproduction

Operation

Step 1: Safe Location

Before starting the portable generator there are two equally

important safety concerns regarding carbon monoxide

poisoning and fire that must be addressed.

Operation Location to Reduce the Risk of

Carbon Monoxide Poisoning

The engine exhaust of all fossil fuel burning equipment,

such as a portable generator, contains carbon monoxide,

a poisonous gas that could kill you in minutes. You cannot

smell it, see it, or taste it. Even if you do not smell exhaust

fumes, you could still be exposed to carbon monoxide gas.

By law it is required in many states to have a carbon

monoxide alarm in operating condition in your home. A

carbon monoxide alarm is an electronic device that detects

hazardous levels of carbon monoxide. When there is

a buildup of carbon monoxide, the alarm will alert the

occupants by flashing visual indicator light and alarm.

Smoke alarms cannot detect carbon monoxide gas.

DANGER! Engine exhaust contains carbon

monoxide, a poisonous gas that could kill you in

minutes. You cannot smell it, see it, or taste it.

Even if you do not smell exhaust fumes, you could still be

exposed to carbon monoxide gas.

• Operate this product only outdoors far away from

windows, doors and vents to reduce the risk of carbon

monoxide gas from accumulating and potentially being

drawn towards occupied spaces.

• Install battery-operated carbon monoxide alarms or

plug-in carbon monoxide alarms with battery back-up

according to the manufacturer’s instructions. Smoke

alarms cannot detect carbon monoxide gas.

• Do not run this product inside homes, garages,

basements, crawlspaces, sheds, or other partially-

enclosed spaces even if using fans or opening doors

and windows for ventilation. Carbon monoxide can

quickly build up in these spaces and can linger for

hours, even after this product has shut off.

• Always place this product downwind and point the

engine exhaust away from occupied spaces.

If you start to feel sick, dizzy, or weak while using this

product, get to fresh air right away. See a doctor. You may

have carbon monoxide poisoning.

Carbon monoxide alarm

Install carbon monoxide alarms inside

your home. Without working carbon

monoxide alarms, you will not realize

you are getting sick and dying from

carbon monoxide poisoning.

CARBON MONOXIDE ALARM(S)

USE OUTDOORS - AVOID CARBON MONOXIDE POISONING

point away

from home

MUFFLER

To better educate yourself about all carbon monoxide risks,

go to www.takeyourgeneratoroutside.com.

Not for

Reproduction

8 BRIGGSandSTRATTON.COM

Operation

Operation Location to Reduce the Risk of Fire

WARNING!

Exhaust heat/gases could ignite

combustibles, structures or damage fuel tank

causing a fire, resulting in death or serious injury.

• Portable generator must be at least 5 ft. (1.5 m) from

any structure, overhang, trees, windows, doors, any wall

opening, shrubs, or vegetation over 12 in. (30.5 cm) in

height.

• Do not place portable generator under a deck or other

type of structure that may confine airflow. Smoke alarm(s)

must be installed and maintained indoors according to the

manufacturer’s instructions/recommendations.

• Carbon monoxide alarms cannot detect smoke.

• Do not place portable generator in manner other than

shown.

MUFFLER

5 ft. (1.5 m)

min.

5 ft. (1.5 m)

min.

Not for

Reproduction

Operation

Step 2: Oil and Fuel

Fuel must meet these requirements:

• Clean, fresh, unleaded fuel with a minimum of 87 octane.

• Gasoline with an ethanol content up to 10% is acceptable.

E10

E15

NOTICE Do not mix oil in fuel or modify engine to run on

alternate fuels. Use of unapproved fuels could damage

engine and will not be covered under warranty.

See High Altitude for 5,000 ft. and above.

WARNING! Fuel and its vapors are extremely

flammable which could cause burns or fire

resulting in death or serious injury.

• Do not refuel during operation.

• Turn engine off and let it cool at least 2 minutes before

removing fuel cap.

• Fill fuel tank outdoors. Keep fuel away from sparks, open

flames, pilot lights, heat, and other ignition sources.

Check fuel lines, tank, cap and fittings frequently for

cracks or leaks. Replace if necessary.

1. Move generator outdoors to a flat, level surface.

2. Clean area around oil fill and remove oil fill cap/

dipstick.

3. Slowly pour contents of oil bottle into oil fill opening.

Checking oil level frequently, fill to point of overflowing.

NOTICE Pause to permit oil to settle. Wipe dipstick clean

each time oil level is checked. DO NOT overfill.

4. Replace and fully tighten oil fill cap/dipstick.

5. Slowly remove fuel cap to relieve pressure in tank.

6. Slowly add unleaded fuel to fuel tank. Be careful not

to fill above lip. This allows adequate space for fuel

expansion.

7. Install fuel cap and let any spilled fuel evaporate

before starting engine.

High Altitude

At altitudes over 5,000 ft. (1524 m), a minimum 85 octane

fuel is acceptable. To remain emissions compliant, high

altitude adjustment is required. Operation without this

adjustment will cause decreased performance, increased

fuel consumption,

and increased emissions.

See an authorized Briggs & Stratton dealer for high altitude

adjustment information. Operation of the engine at altitudes below

2,500 ft. (762 m) with the high altitude kit is not recommended.

Transporting

When transporting equipment with a vehicle or trailer, turn fuel

shutoff valve to off (0) position. Do not tip engine or equipment at

an angle which causes fuel to spill.

Step 3: Generator Start Up

Disconnect all electrical loads from the generator. Use the

following start instructions:

1. Make sure unit is outdoors on a level surface.

NOTICE Failure to operate the unit on a level surface may

cause the unit to shut down.

2. Turn the fuel valve to the on (I) position.

3. Push choke lever to choke ( ) position.

4. Set engine switch to on (I) position.

5. Grasp recoil handle and pull slowly until slight

resistance is felt. Then pull rapidly to start engine.

6. Slowly move choke lever to run ( ) position. If engine

falters, move choke lever to half choke position until

engine runs smoothly, and then to run ( ) position.

NOTICE If engine starts but fails to run, see Low Oil

Shutdown in Features and Controls.

Fuel Valve

Engine

Switch

Choke Lever

Not for

Reproduction

10 BRIGGSandSTRATTON.COM

Operation

Step 4: Connecting Electrical Loads

Using Extension Cords

Use only grounded extension cords marked for outdoor

use rated for your loads. Follow cord safety instructions.

WARNING! Damaged or overloaded extension

cords could overheat, arc, and burn resulting in

death or serious injury.

NOTICE For generator output required see Generator

Capacity. Connect electrical loads in off position then turn

on for operation.

120 Volt AC, 20 Amp, GFCI Duplex Receptacle

Use receptacle to operate 120 Volt AC, single-phase, 60 Hz

electrical loads requiring up to 2,400 Watts (2.4 kW) at 20

Amps of current.

Ground Fault Protection

The duplex receptacle is equipped with Ground Fault

Circuit Interrupter (GFCI) protection. The GFCI protects

against electrical shock that may be caused if your body

becomes a path which electricity travels to reach ground.

When protected by a GFCI, one may still feel a shock, but

the GFCI is intended to cut current off quickly enough so

that a person in normal health should not suffer any serious

electrical injury.

WARNING! Generator voltage could cause

electrical shock or burn resulting in death or

serious injury. Contact with the hot and neutral

conductor at the same time could cause electrical shock

or burn, even if the circuit is GFCI protected.

Testing the GFCI

Test your GFCI outlet prior to each use, as follows:

• Push the “Test” button. The “Reset” button should pop

out, which should allow no power to reach the outlet.

• Press the “Reset” button firmly until it is fully in place

and locks in that position. If the GFCI outlet does not

reset properly, do not use the outlet. Call or take your

generator to a local service center.

• If the GFCI trips by itself at any time, reset and test the

outlet.

120/240 Volt AC, 20 Amp, Locking Receptacle

Use a NEMA L14-20 plug with this receptacle. Connect a

4-wire cord set rated for 250 Volt AC loads at 20 Amps.

The generator’s locking receptacle is not protected by a

GFCI.

This receptacle powers 120/240 Volt AC, 60 Hz, single

phase loads requiring up to 3,500 watts of power (3.5 kW)

at 14.6 Amps for 240 Volts or two independent 120 Volt

loads at 14.6 Amps each.

4-Wire Cord Set

240V

120V

W (Neutral)

X (Hot)

Y (Hot)

NEMA L14-20

Ground (Green)

Not for

Reproduction

Operation

Generator Capacity

To make sure your generator can supply enough running

watts and starting watts for the items you will power at the

same time, follow these simple steps:

1. Select the items you will power at the same time. See

following list for typical wattages.

* Typical wattages listed are approximate only. Check tool

or appliance for actual wattage.

** Per Briggs & Stratton 628K, Starting Watts represents

the momentary electrical current the generator can

provide to start electric motors. Starting Watts does

not represent the power required to continuously run

electrical loads. Starting Watts is the maximum current

that can momentarily be supplied when starting a motor,

multiplied by the generator’s rated voltage.

2. Total the running watts. This is the amount of power

your generator must produce to keep your items

running. See following example:

Example

Total running watts = 2355

Highest starting watts = 2000

Total generator watts required = 4355

3. Estimate the starting watts you will need. Because not

all motors start at the same time, total starting watts

can be estimated by adding only the item with the

highest additional starting watts requirements to the

total running watts from step 2.

Power Management

To manage generator power, sequentially add loads as

follows:

1. With nothing connected to generator, start the engine

outdoors.

2. Plug in and turn on the first load, preferably the largest

load you have.

3. Permit the generator output to stabilize (engine runs

smoothly and attached device operates properly).

4. Plug in and turn on the next load.

5. Again, permit the generator to stabilize.

6. Repeat steps 4 and 5 for each additional load.

Never add more loads than the generator capacity. Take

special care to consider surge loads in generator capacity.

Step 5: Generator Shutdown

1. Turn off and unplug all electrical loads from generator

panel receptacles. Never stop engine with electrical

devices plugged in and turned on.

2. Let engine run at no-load for one minute to stabilize

internal temperatures of engine and generator.

3. Push engine switch to off (0) position.

4. Move fuel valve to off (0) position.

Tool or

Appliance

Running Watts Starting Watts

Air Conditioner

1200 1800

Refrigerator 800 2000

Television 280 —

Light (75 Watts) 75 —

2355 Total

Running Watts

2000 Highest

Starting Watts

Tool or Appliance

Running

Watts*

Starting

Watts**

Light Bulb - 75 Watt 75 -

Pump 800 1200

Refrigerator/Freezer 800 2000

Water Pump - 1/3 HP 1000 2000

Air Conditioner- 13,500 BTU 1200 1800

Furnace Fan Blower - 1/2 HP 800 1300

Microwave Oven - 1000 Watt 1000 -

Color Television - 42” 280 -

Personal Computer w/17” monitor 800 -

Not for

Reproduction

12 BRIGGSandSTRATTON.COM

Maintenance

Maintenance Schedule

Follow the hourly or calendar intervals, whichever occurs

first. More frequent service is required when operating in

adverse conditions noted below.

Service more often under dirty or dusty conditions.

See any authorized dealer for service.

General Recommendations

Regular maintenance will improve the performance and

extend the life of the generator. See any authorized dealer

for service.

The generator’s warranty does not cover items that have

been subjected to operator abuse or negligence. To

receive full value from the warranty, the operator must

maintain the generator as instructed in this manual.

All service and adjustments should be made at least once

each season. A new spark plug and clean air filter assure

proper fuel-air mixture and help your engine run better and

last longer. Follow requirements in Maintenance Schedule.

Emissions Control

Maintenance, replacement, or repair of the emissions

control devices and systems may be performed by any

non-road engine repair establishment or individual.

However, to obtain ”no charge” emissions control service,

the work must be performed by a factory authorized dealer.

See Emissions Warranty.

Cleaning

Daily or before use, look around and underneath

the generator for signs of oil or fuel leaks. Clean any

accumulated debris. Keep area around muffler free from

any debris.

• Use a soft bristle brush to loosen caked on dirt or oil.

• Use a damp cloth to wipe exterior surfaces clean.

NOTICE Improper treatment of generator could damage

it and shorten its life. Do not expose generator to excessive

moisture, dust, dirt, or corrosive vapors. Do not insert any

objects through cooling slots.

Fuel Valve Maintenance

The fuel valve is equipped with a fuel sediment cup,

screen, and o-ring that need to be cleaned.

1. Move fuel valve to off (0) position.

2. Remove sediment cup from fuel valve. Remove o-ring

and screen from fuel valve.

3. Wash sediment cup, o-ring, and screen in a

nonflammable solvent. Dry them thoroughly.

4. Place screen and o-ring into fuel valve. Install

sediment cup and tighten securely.

5. Move fuel valve to on (I) position, and check for leaks.

Replace fuel valve if there is any leakage.

Screen

O-Ring

Sediment Cup

First 5 Hours

• Change engine oil

Every 8 Hours or Daily

• Clean debris

• Check engine oil level

Every 25 Hours or Yearly

• Clean engine air filter

Every 50 Hours or Yearly

• Change engine oil

Yearly

• Replace engine air filter

• Service fuel valve

• Service spark plug

• Inspect muffler and spark arrester

• Clean cooling system

1, 2

Not for

Reproduction

Maintenance

Engine Maintenance

Oil Recommendations

We recommend the use of Briggs & Stratton Warranty

Certified oils for best performance. Other high-quality

detergent oils are acceptable if classified for service SF

or higher. Do not use special additives. See Common

Service Parts.

Outdoor temperatures determine the proper oil viscosity for

the engine. Use the chart to select the best viscosity for the

outdoor temperature range expected.

* Below 4°C (40°F) the use of SAE 30 will result in hard starting.

** Above 27°C (80°F) the use of 10W30 may cause increased oil

consumption. Check oil level more frequently.

Checking/Adding Engine Oil

Oil level should be checked prior to each use or at least

every 8 hours of operation. Keep oil level maintained.

1. Make sure generator is on a level surface.

2. Clean area around oil fill, remove dipsitck and wipe

with clean cloth. Replace dipstick. Remove and check

oil level.

NOTICE Do not screw in dipstick when checking oil level.

3. Verify oil is at full mark on dipstick.

4. If needed, slowly pour oil into oil fill opening to the

point of overflowing.

5. Replace and tighten dipstick.

NOTICE Do not attempt to crank or start engine before

it has been properly serviced with recommended oil. This

could result in an engine failure.

CAUTION Avoid prolonged or repeated skin contact

with used motor oil. Used motor oil has been shown

to cause skin cancer in certain laboratory animals.

Thoroughly wash exposed areas with soap and water.

KEEP OUT OF REACH OF CHILDREN. DON’T

POLLUTE. CONSERVE RESOURCES. RETURN

USED OIL TO COLLECTION CENTERS.

Changing Engine Oil

If you are using your generator under extremely dirty or

dusty conditions, or in extremely hot weather, change the

oil more often.

Change the oil while the engine is still warm from running,

as follows:

1. Make sure unit is on a level surface.

2. Remove oil drain plug and drain oil completely into a

suitable container.

3. Reinstall oil drain plug and tighten securely. Remove

dipstick.

4. Slowly pour recommended oil (about 20 oz. (0.6 l))

into oil fill opening. Pause to permit oil to settle. Fill to

Full mark on dipstick.

5. Wipe dipstick clean each time oil level is checked. Do

not overfill.

6. Reinstall dipstick. Tighten cap securely.

7. Wipe up any spilled oil.

Oil Drain Plug

Not for

Reproduction

14 BRIGGSandSTRATTON.COM

Maintenance

Service Air Cleaner

Your engine will not run properly and may be damaged if

you run it with a dirty air cleaner. Clean or replace more

often if operating under dusty or dirty conditions.

To service the air cleaner, follow these steps:

1. Unclamp latches that hold on the cover.

2. Remove cover and foam air filter.

3. Wash the foam air filter in liquid detergent and water.

Squeeze dry the foam air filter in a clean cloth.

NOTICE If the filter is excessively dirty, replace with a

new filter. See Common Service Parts.

4. Saturate the foam air filter with clean engine oil. To

remove the excess engine oil, squeeze the foam air

filter in a clean cloth.

5. Reinstall clean or new foam air filter.

6. Reinstall the air filter cover and re-clamp latches.

Service Spark Plug

Changing the spark plug will help your engine to start

easier and run better.

1. Clean area around spark plug.

2. Remove and inspect spark plug.

3. Replace spark plug if electrodes are pitted, burned

or porcelain is cracked. Use the recommended

replacement spark plug. See Common Service Parts.

4. Check electrode gap with wire feeler gauge and reset

spark plug gap to recommended gap if necessary

(see Specifications).

5. Install spark plug and tighten firmly.

Inspect Muffler and Spark Arrester

The engine exhaust muffler has a spark arrester screen.

Inspect the muffler for cracks, corrosion, or other damage.

Inspect spark arrester screen for damage or carbon

blockage. Clean if carbon blockage is found using brush

and commercial solvent or replace if damaged.

WARNING!

Contact with muffler area could

cause burns resulting in serious injury.

• Do not touch hot parts.

• It is a violation of California Public Resource Code,

Section 4442, to use or operate the engine on any forest-

covered, brush-covered, or grass-covered land unless

the exhaust system is equipped with a spark arrester, as

defined in Section 4442, maintained in effective working

order. Other states or federal jurisdictions may have

similar laws, reference Federal Regulation 36 CFR Part

261.52.

Replace spark arrester as follows:

1. Remove four screws that connect heat shield to

muffler.

2. Remove four screws that attach spark arrester screen.

3. Obtain a replacement screen. See Common Service

Parts.

4. Reattach screen and muffler guard.

Common Service Parts

Air Cleaner .............................594234

Spark Plug .............................798615

Engine Oil Bottle ........................100028

Synthetic Oil Bottle ......................100074

Fuel Stabilizer .................100120 or 100117

Spark Arrester ........................ 83083GS

Contact an authorized service dealer or

BRIGGSandSTRATTON.com for a full list of parts and

diagrams.

Muffler

Heatshield

Spark Arrester Screen

Screws

Latches

Filter

Cover

Not for

Reproduction

Storage

If storing the unit for more than 30 days, use the following

guidelines to prepare it for storage.

Long Term Storage Instructions

1. Clean the generator as outlined in Cleaning.

2. Change engine oil while engine is still warm, drain oil

from crankcase. Refill with recommended grade. See

Changing Engine Oil.

3. Treat or drain fuel from generator as fuel can become

stale when stored over 30 days.

Stale fuel causes acid and gum deposits to form in the fuel

system or on essential carburetor parts. To keep fuel fresh,

use Briggs & Stratton® Advanced Formula Fuel Treatment

& Stabilizer, available wherever Briggs & Stratton genuine

service parts are sold. See Common Service Parts.

There is no need to drain gasoline from the engine if a

fuel stabilizer is added according to instructions. Run the

engine for 2 minutes to circulate the stabilizer throughout

the fuel system before storage.

If gasoline in the engine has not been treated with a fuel

stabilizer, it must be drained into an approved container.

Run the engine until it stops from lack of fuel. The use of a

fuel stabilizer in the storage container is recommended to

maintain freshness.

WARNING!

Fuel and its vapors are extremely

flammable and explosive which could cause

burns, fire or explosion resulting in death or

serious injury.

• When storing fuel or equipment with fuel in tank, store

away from furnaces, stoves, water heaters, clothes dryers

or other appliances that have pilot light or other ignition

source because they could ignite fuel vapors.

• When draining fuel, turn generator engine off and let it

cool at least 2 minutes before removing fuel cap. Loosen

cap slowly to relieve pressure in tank. Drain fuel tank

outdoors. Keep fuel away from sparks, open flames, pilot

lights, heat, and other ignition sources.

• Check fuel lines, tank, cap and fittings frequently for

cracks or leaks. Replace if necessary.

4. Store generator in clean, dry area and cover with a

suitable protective cover that does not retain moisture.

WARNING! Storage covers could cause a fire

resulting in death or serious injury.

• Do not place a storage cover over a hot generator. Let

equipment cool for a sufficient time before placing the

cover on the equipment.

Not for

Reproduction

16 BRIGGSandSTRATTON.COM

Troubleshooting/Specifications

Problem Cause Correction

Engine is running, but no AC

output is available.

1. One of the circuit breakers is open.

2. Poor connection or defective cord set.

3. Connected device is bad.

1. Reset circuit breaker.

2. Check and repair.

3. Connect another device that is in

good condition.

Engine runs well at no-load but

“bogs down” when loads are

connected.

1. Generator is overloaded. 1. See Generator Capacity.

Engine will not start; starts and

runs rough or shuts down when

running.

1. Engine switch set to off (0) position.

2. Fuel valve is in off (0) position.

3. Low oil level.

4. Dirty air cleaner.

5. Out of fuel.

6. Spark plug wire not connected to

spark plug.

7. Flooded with fuel.

1. Set switch to on (I) position.

2. Turn fuel valve to on (I) position.

3. Fill crankcase to proper level or

place generator on level surface.

4. Clean or replace air cleaner.

5. Fill fuel tank.

6. Connect wire to spark plug.

7. Wait 5 minutes and re-crank engine.

For all other issues, see a Briggs & Stratton authorized dealer.

Power Ratings: The net torque rating for individual gasoline engine models is labeled in accordance with SAE (Society of Automotive

Engineers) code J1940 Small Engine Power & Torque Rating Procedure, and is rated in accordance with SAE J1349. Net torque values

are derived at 3600 RPM and are taken with exhaust and air cleaner installed. Given the wide array of conditions in which they are

placed, the gasoline engine may not develop the rated net torque when used in a given piece of power equipment. This difference is

due to a variety of factors including, but not limited to, the variety of application limitations, ambient operating conditions (temperature,

humidity, altitude), and engine-to-engine variability. Due to manufacturing and capacity limitations, Briggs & Stratton may substitute an

engine of higher rated torque for this engine.

* Generator certified in accordance with CSA (Canadian Standards Association) standard C22.2 No. 100-14, Motors and Generators

and PGMA (Portable Generator Manufacturers’ Association) standard ANSI/PGMA G300-2015, Safety and Performance of Portable

Generators.

** Per Briggs & Stratton 628K

Specifications

Running Watts* ........................................... 3,500

Starting Watts** ........................................... 4,375

AC Current at 120 Volts ................................29.1 Amps

AC Current at 240 Volts ................................14.6 Amps

Frequency. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Hz at 3600 rpm

Phase .............................................Single Phase

Displacement ................................12.69 cu. in. (208 cc)

Spark Plug Gap ................................0.030 in. (0.76 mm)

Fuel Capacity ...........................5 U.S. Gallons (18.9 Liters)

Oil Capacity ................................20 Ounces (0.6 Liters)

Not for

Reproduction

Troubleshooting

Schematic

Not for

Reproduction

18 BRIGGSandSTRATTON.COM

Warranty

80011053_EN Rev. A

BRIGGS & STRATTON PRODUCTS WARRANTY POLICY

LIMITED WARRANTY

Briggs & Stratton warrants that, during the warranty period specified below, it will repair or replace, free of charge, any part that is defective in material or workmanship

or both. Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is effective for

and is subject to the time periods and conditions stated below. For warranty service, find the nearest Authorized Service Dealer in our dealer locator map at

BRIGGSandSTATTON.COM. The purchaser must contact the Authorized Service Dealer, and then make the product available to the Authorized Service Dealer for

inspection and testing.

There is no other express warranty. Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to the

warranty period listed below, or to the extent permitted by law. Liability for incidental or consequential damages are excluded to the extent exclusion

is permitted by law. Some states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not allow the exclusion

or limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives you specific legal rights and you

may also have other rights which vary from state to state or country to country.**

WARRANTY PERIOD

▲ After 12 months, warranty covers parts only.

* Applies to Briggs & Stratton engines only. Warranty coverage of non-Briggs & Stratton engines is provided by that engine manufacturer. Emissions-related components

are covered by the Emissions Warranty Statement.

** In Australia - Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major

failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be

of acceptable quality and the failure does not amount to a major failure. For warranty service, find the nearest Authorized Service Dealer in our dealer locator map at

BRIGGSandSTRATTON.COM, or by calling 1300 274 447, or by emailing or writing to [email protected], Briggs & Stratton Australia Pty Ltd, 1

Moorebank Avenue, NSW, Australia, 2170.

The warranty period begins on the date of purchase by the first retail or commercial consumer. “Consumer use” means personal residential household use by a retail

consumer. “Commercial use” means all other uses, including use for commercial, income producing or rental purposes. Once a product has experienced commercial

use, it shall thereafter be considered as a commercial use product for purposes of this warranty.

Save your proof of purchase receipt. If you do not provide proof of the initial purchase date at the time warranty service is requested, the manufacturing date of the

product will be used to determine the warranty period. Product registration is not required to obtain warranty service on Briggs & Stratton products.

ABOUT YOUR WARRANTY

Warranty service is available only through Briggs & Stratton Authorized Service Dealers. This warranty covers only defects in materials or workmanship. It does not cover

damage caused by improper use or abuse, improper maintenance or repair, normal wear and tear, or stale or unapproved fuel.

Improper Use and Abuse - The proper, intended use of this product is described in the Operator’s Manual. Using the product in a way not described in the Operator’s

Manual or using the product after it has been damaged will not be covered under this warranty. Warranty coverage will also not be provided if the serial number on the

product has been removed or the product has been altered or modified in any way, or if the product has evidence of abuse such as impact damage or water/chemical

corrosion damage.

Improper Maintenance or Repair - This product must be maintained according to the procedures and schedules provided in the Operator’s Manual, and serviced or

repaired using genuine Briggs & Stratton parts or equivalent. Damage caused by lack of maintenance or use of non-original parts is not covered by warranty.

Normal Wear and Tear - Like most mechanical devices, your unit is subject to wear even when properly maintained. This warranty does not cover repairs when normal

use has exhausted the life of a part or the equipment. Maintenance and wear items such as filters, belts, cutting blades, and brake pads (except engine brake pads) are

not covered by warranty due to wear characteristics alone, unless the cause is due to defects in material or workmanship.

Stale or Unapproved Fuel - In order to function correctly, this product requires fresh fuel that conforms to the criteria specified in the Operator’s Manual. Engine or

equipment damage caused by stale fuel or the use of unapproved fuels (such as E15 or E85 ethanol blends) is not covered by warranty.

Other Exclusions - This warranty excludes damage due to accident, abuse, modifications, alterations, improper servicing, freezing or chemical deterioration.

Attachments or accessories that were not originally packaged with the product are also excluded. There is no warranty coverage on equipment used for primary power in

place of utility power or on equipment used in life support applications. This warranty does not include used, reconditioned, second-hand, or demonstration equipment or

engines. This warranty also excludes failures due to acts of God and other force majeure events beyond the manufacturer’s control.

Item Consumer Use Commercial Use

Equipment 24 months ▲ 12 months

Engine* 24 months 12 months

Battery (if equipped) 3 months None

Not for

Reproduction

Generador portátil para

uso en exteriores

Manual del operador

Número de modelo __________________________

Revisión __________________________________

Número de serie ____________________________

Fecha de compra ___________________________

BRIGGS & STRATTON es una marca

registrada de Briggs & Stratton Corporation.

800-743-4115

BRIGGSandSTRATTON.COM

Not for

Reproduction

2 BRIGGSandSTRATTON.COM2 BRIGGSandSTRATTON.COM

Índice

Descripción del equipo.........................2

Características y controles......................5

Operación ...................................7

Mantenimiento ..............................12

Almacenamiento.............................15

Solución de problemas/Especificaciones.........16

Garantía....................................18

Registre su producto

Con el fin de garantizar la cobertura de la garantía de

forma oportuna y completa, registre su producto en línea

en www.onlineproductregistration.com.

Símbolos y advertencias

Señal Advertencias

PELIGRO

Indica un peligro que, si no se evita,

ocasionará la muerte o lesiones graves.

ADVERTENCIA

Indica un peligro que si no es evitado,

podría ocasionar la muerte o heridas

graves.

PRECAUCIÓN

Indica un peligro que, si no se evita,

podría ocasionar lesiones menores o

moderadas.

AVISO

Indica una información considerada

importante, pero no relacionada con un

peligro.

Símbolo Nombre Explicación

Símbolo de

alerta de

seguridad

Indica un posible riesgo para su

integridad física.

Manual del

operador

El no cumplir con leer y seguir las

advertencias, las instrucciones y

el manual del operador podrían

dar como resultado la muerte o

lesiones graves.

Gases

Tóxicos

El escape del motor contiene

monóxido de carbono, un gas

tóxico que puede matar en

minutos. No puede olerlo ni verlo.

Incendio

El combustible y sus vapores son

extremadamente inflamables, lo

que podría causar quemaduras

o incendios que conlleven la

muerte o lesiones graves.

El escape del motor puede

causar un incendio que conlleve

la muerte o lesiones graves.

Descarga

eléctrica

El generador podría provocar

electrocución que conlleve

lesiones graves o la muerte.

Símbolo Nombre Explicación

Superficie

caliente

El silenciador puede causar

quemaduras que podrían

comportar lesiones graves.

¡ADVERTENCIA! El escape del motor de este

producto contiene sustancias químicas que según

el estado de California pueden causar cáncer,

defectos de nacimiento u otros daños reproductivos.

¡ADVERTENCIA! Ciertos componentes de este

producto y sus accesorios correspondientes

contienen sustancias químicas que según el

estado de California pueden causar cáncer, defectos de

nacimiento u otros daños reproductivos. Lávese las

manos después de manipular estos elementos.

Descripción del equipo

Lea este manual cuidadosamente y familiarícese

con el generador. Conozca sus aplicaciones, sus

limitaciones, y cualquier riesgo implicado. Guarde

estas instrucciones para futuras consultas.

El generador para exteriores es un generador de corriente

alterna (CA), accionado por motor, de campo giratorio

equipado con un regulador de voltaje. Este generador está

diseñado para suministrar energía eléctrica para iluminación,

aparatos, herramientas y motores compatibles. El regulador

de voltaje dentro del generador está diseñado para mantener

el nivel de voltaje de salida automáticamente.

El generador portátil produce energía que puede usarse

para aparatos que empleen los cables prolongadores

incluidos o para restaurar la energía del hogar temporal

por primera vez. Antes del próximo corte de energía de su

hogar, instale uno de los interruptores de transferencia que

aparezca en la lista. Un interruptor de transferencia es un

dispositivo independiente que un electricista con licencia

instala y que permite al generador portátil estar conectado

por cables, mediante una toma de bloqueo, directamente

al sistema eléctrico de su hogar. Los cables prolongadores

conectados al panel de control del generador portátil no

tienen no están diseñados para ser una solución a largo

plazo cuando estén conectados a aparatos dentro de casa.

Se ha realizado el máximo esfuerzo para reunir en este

manual la información más precisa y actualizada. No

obstante, el fabricante se reserva el derecho de modificar,

alterar o mejorar de cualquier otra forma el generador y

este documento en cualquier momento y sin previo aviso.

AVISO Si tiene alguna pregunta acerca del uso esperado,

póngase en contacto con el distribuidor autorizado. Este

equipo se ha diseñado para usarse con partes autorizadas

de Briggs & Stratton únicamente.

Este sistema de encendido por chispa cumple con la

norma canadiense ICES-002.

Descripción del equipo

La page charge ...

Briggs & Stratton 030712-00 Manuel utilisateur

Marque: Briggs & Stratton

Modèle: 030712-00

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

Ce manuel convient également à

030712

Télécharger le PDF

rapport

dans d''autres langues

English: Briggs & Stratton 030712-00 User manual
español: Briggs & Stratton 030712-00 Manual de usuario

Documents connexes

Briggs & Stratton 030713-00 Manuel utilisateur

Briggs & Stratton 030712-00 Manuel utilisateur

Ce manuel convient également à

Briggs & Stratton 030712-00 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents