Champion Power Equipment Pressure Washer Manuel utilisateur

Catégorie
Nettoyeurs haute pression
Taper
Manuel utilisateur

Ce manuel convient également à

OPERATOR'S MANUAL
MODEL #100783
3200 PSI PRESSURE WASHER
Assembled in the USA with USA and foreign components - REV 20200413 Champion Power Equipment, Inc., Santa Fe Springs, CA USA
or visit championpowerequipment.com
SAVE THESE INSTRUCTIONS. This manual contains important safety precautions which should be read and understood before operating the product. Failure to do
so could result in serious injury. This manual should remain with the product.
Specifications, descriptions and illustrations in this manual are as accurate as known at the time of publication, but are subject to change without notice.
REGISTER YOUR PRODUCT ONLINE
at championpowerequipment.com
100783 - 3200 PSI PRESSURE WASHER
TABLE OF CONTENTS
2
TABLE OF CONTENTS
Introduction ................................................... 3
Safety Definitions
..........................................3
Important Safety Instructions
.......................4
Fuel Safety ........................................................ 6
Safety and Dataplate Labels/Tags................................ 7
Safety Symbols .................................................... 8
Operation Symbols ................................................ 9
Quickstart Label Symbols......................................... 9
Controls and Features ................................. 10
Pressure Washer ................................................. 10
Engine ............................................................ 10
Parts Included .................................................... 11
Assembly ..................................................... 12
Remove the Pressure Washer from the Shipping Carton ....... 12
Install Wheels, Support Legs, Detergent Tank, Trigger Gun
Holder, Handle, and Nozzles ....................................... 12
High Pressure Hose Strap ....................................... 13
Attach the Trigger Gun Assembly ................................ 14
Connect the High Pressure Hose ................................ 14
Connect the Garden Hose ........................................ 14
Add Engine Oil .................................................... 15
Add Fuel .......................................................... 15
Operation ..................................................... 15
Pressure Washer Location ....................................... 15
Before Starting the Engine ....................................... 15
Starting the Engine ............................................... 15
Distance from Cleaning Surface ................................. 16
High Pressure Wash .............................................. 17
Low Pressure Wash .............................................. 17
System Flush ..................................................... 18
Depressurize System ............................................ 18
Operating Tips .................................................... 18
Stopping the Engine .............................................. 19
Operation at High Altitude ....................................... 19
Maintenance ................................................ 19
Cleaning the Pressure Washer ................................... 19
Cleaning Spray Nozzle ........................................... 19
Changing the Engine Oil ......................................... 19
Cleaning and Adjusting the Spark Plug(s) ....................... 19
Cleaning the Air Filter ............................................ 19
Cleaning the Spark Arrester ..................................... 19
Maintenance Schedule ........................................... 19
Storage ........................................................20
Pressure Washer Storage ........................................ 20
Engine Storage ................................................... 20
Winter Storage ................................................... 20
Specifications .............................................. 20
Pressure Washer Specifications ................................. 20
Engine Specifications ............................................20
Oil Specifications .................................................20
Fuel Specifications ............................................... 20
Temperature Specifications ......................................20
Parts Diagram .................................................... 21
Parts List ......................................................... 22
Troubleshooting ........................................... 23
100783 - 3200 PSI PRESSURE WASHER
INTRODUCTION
3
SAFETY DEFINITIONS
The purpose of safety symbols is to attract your attention to
possible dangers. The safety symbols, and their explanations,
deserve your careful attention and understanding. The safety
warnings do not by themselves eliminate any danger. The
instructions or warnings they give are not substitutes for proper
accident prevention measures.
DANGER
DANGER indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
WARNING
WARNING indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
NOTICE
NOTICE indicates information considered important, but not
hazard-related (e.g., messages relating to property damage).
INTRODUCTION
Congratulations on your purchase of a Champion Power Equipment
(CPE) product. CPE designs, builds, and supports all of our
products to strict specifications and guidelines. With proper
product knowledge, safe use, and regular maintenance, this
product should bring years of satisfying service.
Every effort has been made to ensure the accuracy and
completeness of the information in this manual at the time of
publication, and we reserve the right to change, alter and/or
improve the product and this document at any time without prior
notice.
CPE highly values how our products are designed, manufactured,
operated, and serviced as well as providing safety to the
operator and those around the pressure washer. Therefore, it is
IMPORTANT to review this product manual and other product
materials thoroughly and be fully aware and knowledgeable of
the assembly, operation, dangers and maintenance of the product
before use. Fully familiarize yourself, and make sure others who
plan on operating the product fully familiarize themselves too,
with the proper safety and operation procedures before each use.
Please always exercise common sense and always err on the
side of caution when operating the product to ensure no accident,
property damage, or injury occurs. We want you to continue to use
and be satisfied with your CPE product for years to come.
When contacting CPE about parts and/or service, you will need to
supply the complete model and serial numbers of your product.
Transcribe the information found on your product’s nameplate
label to the table below
CPE TECHNICAL SUPPORT TEAM
1-877-338-0999
MODEL NUMBER
100783
SERIAL NUMBER
DATE OF PURCHASE
PURCHASE LOCATION
100783 - 3200 PSI PRESSURE WASHER
IMPORTANT SAFETY INSTRUCTIONS
4
IMPORTANT SAFETY INSTRUCTIONS
DANGER
Pressure washer exhaust contains carbon monoxide, a
colorless, odorless, poisonous gas. Breathing carbon monoxide
will cause nausea, dizziness, fainting or death. If you start to
feel dizzy or weak, get to fresh air immediately.
OPERATE PRESSURE WASHER OUTDOORS ONLY IN A WELL
VENTILATED AREA AND POINT EXHAUST AWAY.
DO NOT operate the pressure washer inside any building,
including garages, basements, crawlspaces and sheds,
enclosure or compartment, including the pressure washer
compartment of a recreational vehicle.
DO NOT allow exhaust fumes to enter a confined area through
windows, doors, vents or other openings.
DANGER
Using an engine indoors CAN KILL YOU IN MINUTES. Engine
exhaust contains carbon monoxide. This is a poison you cannot
see or smell.
NEVER use inside a home or garage, EVEN IF doors and
windows are open.
ONLY use OUTSIDE and far away from windows, doors,
and vents.
Install battery-operated carbon monoxide alarms or plug-in
carbon monoxide alarms with battery back-up according to the
manufacturer’s instructions.
DANGER
Rotating parts can entangle hands, feet, hair, clothing and/or
accessories.
Traumatic amputation or severe laceration can result.
Keep hands and feet away from rotating parts.
Tie up long hair and remove jewelry.
Operate equipment with guards in place.
DO NOT wear loose-fitting clothing, dangling drawstrings or
items that could become caught.
WARNING
Spark from removed spark plug wire can result in fire or
electrical shock.
When servicing the pressure washer:
Disconnect the spark plug wire and place it where it cannot
contact the plug or any other metal object.
DO NOT check for spark with the plug removed.
Use only approved spark plug testers.
WARNING
Contact with electrical power source can cause electric shock
or burn.
NEVER spray in the direction of or near a power source/
electrical outlet.
WARNING
Running engines produce heat. Severe burns can occur on
contact. Combustible material can catch fire on contact.
DO NOT touch hot surfaces.
Avoid contact with hot exhaust gases.
Allow equipment to cool before touching.
Maintain at least 3 ft. (91.4 cm) of clearance on all sides to
ensure adequate cooling.
Maintain at least 5 ft. (1.5 m) of clearance from combustible
materials.
NOTICE
DO NOT let water in the pump freeze.
See Storage section in the manual for instructions regarding
winter storage.
If water has frozen in the pressure washer, thaw the pressure
washer in a warm room before starting.
DO NOT pour hot water on or into the pump; internal parts will
be damaged and your warranty will be voided.
NOTICE
NEVER run the unit dry.
Be sure the water supply is completely turned on before
operating the unit.
100783 - 3200 PSI PRESSURE WASHER
IMPORTANT SAFETY INSTRUCTIONS
5
WARNING
NEVER spray flammable liquids or use pressure washer in
areas containing combustible dust, liquids, or vapor.
NEVER operate this machine in a closed building or in or near
an explosive environment.
DO NOT remove fuel tank cap or fill fuel tank while engine
is hot or running (allow engine to cool two minutes before
refueling). Always fill the tank slowly.
NEVER disconnect the high pressure discharge hose from
the machine while the system is pressurized.
WARNING
Rapid retraction of the recoil cord will pull hand and arm
towards the engine faster than you can let go. Unintentional
startup can result in entanglement, traumatic amputation or
laceration. Broken bones, fractures, bruises or sprains could
result.
When starting engine, pull the recoil cord slowly until
resistance is felt and then pull rapidly to avoid kickback.
DO NOT start or stop the engine with electrical devices
plugged in and turned on.
DANGER
Keep clear of nozzle.
DO NOT point the spray wand at a person, an animal or
yourself.
Always wear safety glasses or goggles and protective
equipment (hearing protection, gloves, rubber boots, protective
clothing) when operating or performing maintenance.
NEVER put hand or fingers over the spray tip while
operating the unit.
NEVER try to stop or deflect leaks with any body part.
ALWAYS engage the trigger safety latch in the safe position
when spraying is stopped even if only for a few moments.
WARNING
Always wear eye protection with side shields marked to
comply with ANSI Z87.1.
Following this rule will reduce the risk of serious personal
injury.
NOTICE
Improper treatment or use of the pressure washer can damage
it, shorten its life and void your warranty.
Use the pressure washer only for intended uses.
Operate only on level surfaces.
DO NOT expose pressure washer to excessive moisture, dust,
or dirt.
DO NOT allow any material to block the cooling slots.
DO NOT use the pressure washer if:
Equipment sparks, smokes or emits flames
Equipment vibrates excessively
DANGER
Risk of injection or injury. High pressure jets can be dangerous
if subject to misuse.
DO NOT direct discharge stream at persons, animals,
electrical devices, or the machine itself.
ALWAYS point spray gun in safe direction. Every time you
stop the engine, squeeze trigger of spray gun to relieve any
trapped pressure.
NOTICE
ONLY use cold water.
NOTICE
Water under high pressure can damage fragile surfaces.
ALWAYS: practice on a inconspicuous test area to
understand when damage may occur.
DO NOT: Point spray gun at glass.
NEVER: Point the spray nozzle at persons, animals,
electrical devices, plants or the machine itself.
WARNING
Use of pressure washers can create wet walking surfaces.
While using a pressure washer, forces from the gun can cause
you to loose footing and fall.
Use only on a level surface.
Make sure there is proper drainage to dissipate water.
DO NOT: use on elevated surface where kickback could
result in a serious fall.
ALWAYS grasp the gun with two hands to prevent potential
injury do to high pressure from gun.
100783 - 3200 PSI PRESSURE WASHER
IMPORTANT SAFETY INSTRUCTIONS
6
WARNING
High pressure spray can splash back at operator or propel
objects.
NEVER: allow children to operate any pressure washer or play
nearby.
NEVER: leave spray gun unattended while machine is running
or until after engine has been turned off and pressure has
been relieved from the spray gun.
NEVER: repair high pressure hose, replace it.
NEVER: repair leaking connections with sealant, replace
damaged O-rings.
NEVER: use spray gun with a damaged or altered trigger lock.
NEVER: secure the trigger in the open / spray position.
ALWAYS: keep high pressure hose connected to spray gun and
pump while in use.
ALWAYS: be certain that spray gun nozzles and accessories
are properly attached to the lance.
ALWAYS: wear safety goggles when operating this equipment.
NOTE: Safety goggles cover the sides, top and bottom of the
eyes. Don't confuse safety glasses for goggles.
Fuel Safety
DANGER
GASOLINE AND GASOLINE VAPORS ARE HIGHLY
FLAMMABLE AND EXPLOSIVE.
Fire or explosion can cause severe burns or death.
Gasoline and gasoline vapors:
Gasoline is highly flammable and explosive.
Gasoline can cause a fire or explosion if ignited.
Gasoline is a liquid fuel but it’s vapors can ignite.
Gasoline is a skin irritant and needs to be cleaned up
immediately if spilled on skin or clothes.
Gasoline has a distinctive odor, this will help detect potential
leaks quickly.
Gasoline expands or contracts with ambient temperatures.
Never fill the gasoline tank to full capacity, as gasoline needs
room to expand when temperatures rise.
In the case of any petroleum gasoline fire, flames should never
be extinguished unless the fuel supply valve can be turned
OFF. By not doing so, if a fire is extinguished and the supply
of fuel is not turned OFF, an explosion hazard could be created.
When adding or removing gasoline:
DO NOT light or smoke cigarettes.
Always turn the pressure washer off and let cool for a
minimum of two minutes before removing the gasoline cap.
Afterwards, loosen gasoline cap to relieve pressure from the
gasoline tank.
Only fill or drain gasoline outdoors in a well-ventilated area.
DO NOT pump gasoline directly into the pressure washer at the
gas station. Always use an approved fuel container to transfer
the gasoline to the pressure washer.
DO NOT overfill the gasoline tank.
Always keep gasoline away from sparks, open flames, pilot
lights, heat and other sources of ignition.
When starting the pressure washer:
DO NOT attempt to start a damaged pressure washer.
Always make certain that the gasoline cap, air filter, spark
plug, fuel lines and exhaust system are properly secured,
connected and in place.
Always allow spilled gasoline to evaporate fully before
attempting to start the engine.
Make certain that the pressure washer is resting firmly on
level ground.
When operating the pressure washer:
DO NOT move or tip the pressure washer during operation.
DO NOT tip the pressure washer or allow fuel or oil to spill.
When transporting or servicing the pressure washer:
Make certain that the fuel valve is in the OFF position and the
gasoline tank is empty.
Disconnect the spark plug wire.
When storing the pressure washer:
Store away from sparks, open flames, pilot lights, heat and
other sources of ignition.
Do not store pressure washer or gasoline near furnaces, water
heaters, or any other appliances that produce heat or have
automatic ignitions.
WARNING
Never use a gasoline container, gasoline tank, or any other fuel
item that is broken, cut, torn or damaged.
100783 - 3200 PSI PRESSURE WASHER
IMPORTANT SAFETY INSTRUCTIONS
7
Safety and Dataplate Labels/Tags
These labels warn you of potential hazards that can cause serious injury. Read them carefully.
If a label comes off or becomes hard to read, contact Technical Support Team for possible replacement.
LABEL/TAG DESCRIPTION
A
1395-L-PR-A
DO NOT point at people, pets,
or electrical devices.
Serious injury will result.
To reduce the risk of injury,
user must read and understand
operator’s manual.
WARNING
DANGER
K 109 485 152
ColorsLPN 1395-L-PR
Rev A
Size 70 x 26 mm
Artwork Notes
2mm safe margin;
white to be printed shown in 50%
process magenta
Revision Changes
---
This ar twork belongs to Champion Power Equipment. The contents are confidential and privileged and shall not be disclosed to or used by or for
outside parties without the explicit consent of Champion Power Equipment.
Trigger Gun
B
1
10W-30
4
2
3
GC190 GC160
2093-L-OP-A
DO NOT TOUCH!
Hot surface.
WARNING
NE TOUCHEZ PAS!
Surface chaude.
AVERTISSEMENT
¡NO TOCAR!
Superficie caliente.
ADVERTENCIA
6
5
30 s
1
GC190 GC160
STOP
ColorsLPN 2093-L-OP
Rev A
Size 101 x 53 mm
Artwork Notes
3mm corner radius; 2mm safe margin;
to be printed
on
WHITE
substrate.
Revision Changes
---
This artwork belongs to Champion Power Equipment. The contents are confidential and privileged and shall not be disclosed to or used by or for
outside parties without the explicit consent of Champion Power Equipment.
2945
K 376 485 152 CG1 CG10
Hot Surface
C
NOTI C E
AVISO
AVIS
NOTI C E
AVISO
AVIS
¡UNIDAD SIN ACEITE! Agreg ue aceite antes del arranque. Sólo u se aceite 10W-30,
revise y cambie el aceite por el mo tor Honda manual.
NO OIL IN UNIT! Add oil befor e starting. Use only 10W-30, check an d change oil
per the Honda engine manual.
L'APPAREIL NE CONTIENT PAS D’HUILE! En ajou ter avant le démarrage. Utilisez
uniquement de l’huile 10W-30 vérifiez et ch angez l’huile par le manuel du
moteur Honda.
WARNING
ADVERTENCIA AVERTISSEMENT
DO NOT TOUCH! Exhaust gases, muffler and engi ne components are extremely HO T
and cause burns.
Operation of this equipmen t may create sparks that can star t fires around dry
vegetation. A spark arr estor may be required. The operat or should contact local fire
agencies for laws and regulatio ns relating to fire prevention requir ements. If
installed, clean per the Ho nda engine manual.
¡NO TOCAR! Los gases de escape, el silenciador y los comp nonentes del motor están
extremadamente CALIENTES y causan quemaduras.
La operación de este equip o puede producir chispas que puede n provocar incendios
alrededor de la vegetación se ca. Un supresor de chispas pued e que sea necesario.
El operador debe comunicar se con las agencias locales de bomb eros para las leyes y
reglamentos relativos a los r equisitos de prevención de incendio s. Si está instalado,
limpie por el motor Honda manual.
DANGER PELIGRO DANGER
NE PAS TOUCHER! Les gaz d’échappement, le silencieux et les pièce s du moteur
sont extrêmement CH AUDS et peuvent causer des brûlur es.
Cet équipement peut créer de s étincelles et provoquer un incendie da ns la
végétation sèche. Un pare-étincelles peut être requis. L’opérateur doit communiquer
avec le service d’incendie loca l pour connaître les lois et les règle ments en matière
de prévention des incendies. S i elle est installée, nettoyez par le ma nuel du
moteur Honda.
Read the operato r’s manual. To reduce th e risk of injury, use r must read and unde rstand
operator’s manual before using this product.
Lea el manual del ope rador. Para reduci r el riesgo de herid a, el usuario deb e leer y entender el
manual del operad or antes de usar es te producto.
Lire attentivement ce manuel d’utilisation. Pour réduire le risque de blessures, l’utilisateur doit
lire et comprendr e le manuel d’utilis ation avant d’uti liser ce produit .
Eye and Ear Protec tion. Always wea r safety goggle s or safety glas ses with side shie lds, and as
necessary a ful l faceshield as wel l as full ear prote ction when oper ating this produ ct.
Protección de ojo s y oídos. Use siemp re gafas de segur idad o gafas de seg uridad con
protectores la terales, y segú n sea necesario un p rotector faci al completo, así c omo una
protección completa para los oídos al operar este producto.
Protection des y eux et des oreilles . Toujours porte r des lunettes de s écurité ou des lun ettes de
sécurité avec des éc rans latéraux e t, si nécessair e, un écran facia l complet ainsi qu'u ne
protection aud itive complète l ors de l'utilisat ion de ce produit .
Kickback. To redu ce the risk of injur y from kickbac k, hold the trigg er gun securely wi th both
hands when the mach ine is on.
Contragolpe. P ara reducir el rie sgo de lesiones po r contragolpe, s ostenga la pist ola de gatillo
firmemente con amb as manos cuando la m áquina esté ence ndida.
Rebond. Afin de réd uire le risque de ble ssures causée s par le rebond, main tenez le pistole t de
déclenchement solidement avec les deux mains lorsque la machine est en marche.
Electric Shock . Failure to use in dr y conditions a nd to observe saf e practices can r esult in
electric shock.
Choque eléctri co. No usar en cond iciones secas y o bservar las p rácticas seg uras pueden pr ovocar
descargas eléctricas.
Décharge électrique. Défaut d'utiliser dans des conditions sè ches et d'observe r les pratiques de
sécurité peut causer un choc électrique.
Risk of Injectio ns. To reduce the risk o f injection or inju ry, never direct a wat er stream towar ds
people or pets or pl ace any body par t in the stream. Lea king hoses and fit tings are also c apable
of causing inject ion injury. Do not ho ld hoses or fitti ngs.
Riesgo de inyeccio nes. Para reduc ir el riesgo de inyecc ión o herida, nun ca dirija una corr iente
acuática hacia la g ente o animales dom ésticos o coloq ue cualquier par te del cuerpo en la
corriente. El es cape de manguera s y accesorios ta mbién es capaz de c ausar la herida de
inyección. No sostenga mangueras o accesorios.
Risque d'injecti ons. Pour réduir e le risque d'injec tion ou de blessur e, ne jamais dirige r un jet
d'eau vers les perso nnes ou les animau x ou placer une par tie du corps dans le r uisseau. Les
tuyaux et raccor ds qui fuient peu vent également ca user des blessur es par injection . Ne pas
tenir les tuyaux ou l es raccords.
Risk of Explosi on. Do not spray flam mable liquids. Fl ammable liquids , fuel, and their va pors are
explosive and can c ause severe burn s or death.
Riesgo de explosi ón. No rocíe líquid os inflamables. L os líquidos infla mables, el combu stible y
sus vapores son exp losivos y pueden c ausar quemadur as graves o la muer te.
Risque d'explosion. Ne pas vaporiser de liquides inflammables. Les liquides inflammables, le
carburant et leu rs vapeurs son t explosifs et peu vent causer de gra ves brûlures ou la mo rt.
Risk of Fire. Fuel an d its vapors are ex tremely flamma ble and explosive . Fire can cause seve re
burns or death. Do n ot add fuel while th e product is oper ating or still hot . Do not spray
flammable liquids . Operate only wh ere open flame is per mitted.
Riesgo de incendi o. El combustible y s us vapores son ex tremadamente i nflamables y
explosivos. El fu ego puede causa r quemaduras gra ves o la muerte. No añ ada combustib le
mientras el prod ucto esté en fun cionamiento o aún c aliente. No rocí e líquidos inflama bles.
Operar sólo cuan do se permite la llam a abierta.
Risque d'incendi e. Le carburant e t ses vapeurs son t extrêmement in flammables et exp losifs. Le feu pe ut causer
de graves brûlure s ou la mort. Ne pas a jouter de carbu rant pendant qu e le produit fonc tionne ou est enco re
chaud. Ne pas vaporiser de liquides inflammables. Utiliser uniquement si la flamme nue est autorisée.
Toxic Fumes. The engine e xhaust from thi s product cont ains chemicals k nown to the state o f
California to ca use cancer and bir th defects an d other reprodu ctive harm. Ris k of Asphyxiat ion.
This engine emits c arbon monoxide , an oderless, co lorless poison g as. Breathing c arbon
monoxide can caus e nausea, faint ing or death. Use on ly in a well ventilate d area.
Vapores tóxicos . Los gases de comb ustión de motor de e ste producto c ontienen prod uctos
químicos conoci dos al estado de Ca lifornia caus ar cáncer y defec tos de nacimiento y o tro daño
reproductivo . Riesgo de Asfix ia. Este motor em ite el monóxido de c arbono, un oderl ess, el gas tóxic o incoloro.
La respiración d el monóxido de car bono puede causa r la náusea, el des mayo o la muerte. Só lo use en un área
bien ventilada.
Gaz d'échappement toxiques. L'échappement du moteur de ce produit contient des produits chimiques connus
de l'état de Califo rnie pour causer l e cancer et les malf ormations cong énitales et d'au tres dommages à la
reproduction . Risque d'asphy xie. Ce moteur éme t du monoxyde de ca rbone, un gaz inof fensif et inco lore. La
respiration de mo noxyde de carbo ne peut causer des n ausées, des évan ouissements ou l a mort. Utilis er
uniquement dans un endroit bien ventilé.
Risk of chemical bu rns. Do not use acid ic, toxic, or corr osive chemicals w ith this produc t.
Riesgo de quemaduras químicas. No utilice s ustancias quím icas ácidas, tóxi cas o corrosiva s
con este producto.
Risque de blessures chimiques. N’utiliser aucun produit chimique acide, toxique ou corrosif
avec ce produit.
2028-T- SF-A
WARNING: Cancer and
Reproductive Harm –
www.P65Warnings.ca.gov
ADVERTENCIA: Cáncer y Daño
Reproductivo
www.P65Warnings.ca.gov
AVERTISSEMENT : Cancer et Troubles de
l'appareil reproducteur
www.P65Warnings.ca.gov
K 152 485 2945 109
ColorsLPN 2028-T-SF
Rev A
Size 109 .5 x 385 mm
Artwork Notes
2mm safe margin;
to be printed on
WHITE
substrate.
Revision Changes
---
This artwork belon gs to Champion Power Equi pment. The content s are confidential a nd privileged and shall n ot be disclosed to or use d by or for
outside parties wit hout the explicit co nsent of Champion P ower Equipment.
Safety Symbols
D
2020-L-SF-A
DANGER
Risk of Exp losion. Do not s pray flammable li quids. Flamma ble
liquids, f uel, and their va pors are explo sive and can caus e severe
burns or dea th.
Risque d'explosion. Ne pas vaporiser de liquides inflammables.
Les liquid es inflammable s, le carburan t et leurs vapeur s sont explosi fs et
peuvent ca user de graves br ûlures ou la mor t.
Kickback. To reduce the risk of injury from
kickback, hold the trigger gun securely with
both hands when the machine is on.
Rebond. Afin de réduire le risque de
blessures causées par le rebond, maintenez le pistolet de
déclenchement solidement avec les deux mains lorsque la
machine est en marche.
Eye and Ear Pr otection. A lways wear safe ty goggles or s afety
glasses with side shields, and as necessary a full faceshield
as well as ful l ear protect ion when opera ting this produ ct.
Protection des yeux et des oreilles. Toujours porter des
lunettes de sécurité ou des lunettes de sécurité avec des écrans latéraux et,
si nécessaire, un écran facial complet ainsi qu'une protection auditive
complète lors de l'utilisation de ce produit.
Risk of Fire . Fuel and its vapo rs are extrem ely flammable an d explosive. Fir e can cause
severe burn s or death. Do not a dd fuel while the p roduct is oper ating or still h ot. Do not
spray flammable liquids. Operate only where open flame is permitted.
Risque d'in cendie. Le car burant et ses vap eurs sont ext rêmement infl ammables et
explosif s. Le feu peut cau ser de graves brû lures ou la mort . Ne pas ajoute r de carburant p endant que
le produit fonctionne ou est encore chaud. Ne pas vaporiser de liquides inflammables. Utiliser
uniquemen t si la flamme nue est a utorisée.
Read the ope rator’s manua l. To reduce
the risk of in jury, user must r ead and
understand operator’s manual before
using this product.
Lire atte ntivement ce ma nuel d’utilisa tion. Pour
réduire le r isque de blessu res, l’utilisa teur doit lire et
comprend re le manuel d’uti lisation avan t d’utiliser
ce produit.
Electric S hock. Failur e to use
in dry conditions and to
observe s afe practice s can
result in ele ctric shock .
Décharge é lectrique. D éfaut d'util iser dans
des conditions sèches et d'observer les
pratiques de sécurité peut causer un
choc électrique.
Risk of Inje ctions. To reduc e the risk of injec tion or injury, ne ver direct a
water stre am towards peop le or pets or plac e any body part i n the stream.
Leaking hoses and fittings are also capable of causing injection injury.
Do not hold ho ses or fitting s.
Risque d'in jections. Po ur réduire le ris que d'injectio n ou de blessure, n e jamais diriger
un jet d'eau ver s les personne s ou les animaux ou p lacer une part ie du corps dans l e
ruisseau . Les tuyaux et r accords qui fu ient peuvent ég alement cause r des blessures p ar
injectio n. Ne pas tenir les t uyaux ou les rac cords
Toxic Fumes. Th e engine exhaus t from this prod uct contain s chemicals kno wn to the state of C alifornia to c ause
cancer and b irth defect s and other rep roductive ha rm. Risk of Asph yxiation. T his engine emits c arbon monoxi de,
an oderles s, colorless p oison gas. Br eathing carbo n monoxide can ca use nausea, f ainting or deat h. Use only in a
well ventilated area.
Gaz d'échappement toxiques. L'échappement du moteur de ce produit contient des produits chimiques connus de l'état de
Califor nie pour causer l e cancer et les mal formations c ongénitales e t d'autres domm ages à la reprodu ction. Risqu e
d'asphyx ie. Ce moteur éme t du monoxyde de c arbone, un gaz i noffensif et i ncolore. La re spiration de m onoxyde de carb one
peut causer des nausées, des évanouissements ou la mort. Utiliser uniquement dans un endroit bien ventilé.
K 485 2945 --- ---
ColorsLPN 2020-L-SF
Rev. A
Size 157 x 32 mm
Artwork Notes
3mm corner radius; 2mm safe margin;
to be printed
on
WHITE
substrate.
Revision Changes
--
This ar twork belongs to Champion Power E quipment. The co ntents are con fidential and pr ivileged and shall n ot be disclosed t o or used by or for
outside parties with out the explicit con sent of Champion P ower Equipment.
E
CHAMPION POWER EQUIPMENT, INC.
SANTA FE SPRINGS, CA 90670 USA / É.-U.
1-877-338-0999
WWW.CHAMPIONPOWEREQUIPMENT.COM
Assembled in the USA with USA and foreign
components / Assemblé aux États-Unis avec
des composants américains et étrangers
2136-L-PR-A
MANUFACTURE DATE
DATE DE FABRICATION
SERIAL NO.
N° DE SÉRIE
MODEL
MODÉLE
100783
GASOLINE DRIVEN, COLD WATER ONLY /
ALIMENTÉE PAR MOTEUR À ESSENCE,
EAU FROIDE SEULEMENT
XXXX
XXXXXXXXXXXX
K --- --- --- ---
ColorsLPN 2136-L-PR
Rev A
Size 51 x 71 mm
Artwork Notes
3mm co rner rad ius; 2mm s afe margi n; to be prin ted
on sec urity su bstrat e; magent a text to be fil led in
duri ng time of p roduct ion
Revision Changes
This ar twork belong s to Champion Powe r Equipment. The c ontents are confidential an d privileged and shall not be disclosed to or used by or for
outside parties wit hout the explicit c onsent of Champio n Power Equipment .
Dataplate
C
D
B
E
A
100783 - 3200 PSI PRESSURE WASHER
IMPORTANT SAFETY INSTRUCTIONS
8
Safety Symbols
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these
symbols will allow you to more safely operate the product.
SYMBOL MEANING
Read Operators Manual. To reduce the risk of injury, user must read and understand operator’s manual
before using this product.
Electric Shock. Failure to use in dry conditions and to observe safe practices can result in electric
shock.
Toxic Fumes. The engine exhaust from this product contains chemicals known to the state of California
to cause cancer and birth defects and other reproductive harm.
Risk of Asphyxiation. This engine emits carbon monoxide, an oderless, colorless poison gas. Breathing
carbon monoxide can cause nausea, fainting or death. Use only in a well ventilated area.
Risk of Injections. To reduce the risk of injection or injury, never direct a water stream towards people
or pets or place any body part in the stream. Leaking hoses and fittings are also capable of causing
injection injury. Do not hold hoses or fittings.
Eye and Ear Protection. Always wear safety goggles or safety glasses with side shields, and as
necessary a full face shield as well as full ear protection when operating this product.
Kickback. To reduce the risk of injury from kickback, hold the trigger gun securely with both hands
when the machine is on.
Risk of Fire. Fuel and its vapors are extremely flammable and explosive. Fire can cause severe burns or
death. Do not add fuel while the product is operating or still hot. Do not spray flammable liquids. Operate
only where open flame is permitted.
Risk of Explosion. Do not spray flammable liquids. Flammable liquids, fuel, and their vapors are
explosive and can cause severe burns or death.
Risk of chemical burns. Do not use acidic, toxic, or corrosive chemicals with this product.
100783 - 3200 PSI PRESSURE WASHER
IMPORTANT SAFETY INSTRUCTIONS
9
Operation Symbols
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these
symbols will allow you to more safely operate the product.
SYMBOL MEANING
0° Nozzle
15° Nozzle
25° Nozzle
SYMBOL MEANING
40° Nozzle
Soap Nozzle
Quickstart Label Symbols
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these
symbols will allow you to more safely operate the product.
2019-L-OP-A
2050-L-OP-A
1
4
5
6
30 s
7
2
3
K
ColorsLPN 2050-L-OP
Rev A
Size 22 x 126 mm
Artwork Notes
3mm corner radius; 2mm safe margin;
to be printed
on
WHITE
substrate.
Revision Changes
---
This artwork belongs to Champion Power Equipment. The contents are confidential and privileged and shall not be disclosed to or used by or for
outside parties without the explicit consent of Champion Power Equipment.
50%
152 2945 376
Set Up
1. Attach wand to trigger gun.
2. Attach high pressure hose to trigger gun.
3. Attach high pressure hose to pump.
4. Attach garden hose.
5. Attach nozzle to trigger gun.
6. Turn on water supply.
7. Press the trigger for 30 seconds.
These are general engine starting and stopping steps. Refer to
Honda’s engine owner/operator manual for additional information.
Starting the Engine
1. Check oil level.
Recommended oil is 10W-30.
2. Check gasoline level.
3. GC190 models:
Rotate engine switch to “ON” position.
3. GC160 models:
Move lever up to “ON” or “FAST position.
4. Pull the choke lever to the “CHOKE” position.
5. Pull the recoil cord.
6. As engine warms up to 30 seconds, push the choke lever to
“RUN” position.
Stopping the Engine
1. GC190 models – Rotate engine switch to “OFF position.
1. GC160 models – Move lever down to “STOP” position.
1
10W-30
4
2
3
GC190 GC160
2093-L-OP-A
DO NOT TOUCH!
Hot surface.
WARNING
NE TOUCHEZ PAS!
Surface chaude.
AVERTISSEMENT
¡NO TOCAR!
Superficie caliente.
ADVERTENCIA
6
5
30 s
1
GC190 GC160
STOP
ColorsLPN 2093-L-OP
Rev A
Size 101 x 53 mm
Artwork Notes
3mm corner radius; 2mm safe margin;
to be printed
on
WHITE
substrate.
Revision Changes
---
This artwork belongs to Champion Power Equipment. The contents are confidential and privileged and shall not be disclosed to or used by or for
outside parties without the explicit consent of Champion Power Equipment.
2945
K 376 485 152 CG1 CG10
100783 - 3200 PSI PRESSURE WASHER
CONTROLS AND FEATURES
10
CONTROLS AND FEATURES
Read this operators manual before operating your pressure washer. Familiarize yourself with the location and function of the controls and
features. Save this manual for future reference.
Pressure Washer
1
11
10
2
8
7
9
6
21
22
20
19
23
24
12
13
14
5
15
16
17
1. Upper Handle
2. Nozzles
3. Trigger Gun
4. Trigger Gun Holder
5. Spray Wand
6. Wheels
7. Detergent Tank Cap
8. Support Leg
9. Detergent Tank
10. High Pressure Hose
11. High Pressure Hose Storage Strap
12. Detergent Barb
13. High Pressure Outlet
14. Garden Hose Inlet
Engine
15. Choke
16. Engine Switch
17. Recoil Starter
18. Oil Drain Bolt
19. Engine Oil Fill Cap/Dipstick
20. Muffler
21. Spark Plug
22. Air Filter
23. Gasoline Tank Cap
24. Gasoline Tank
18
3
4
100783 - 3200 PSI PRESSURE WASHER
CONTROLS AND FEATURES
11
Parts Included
Part Part Qty. Hardware Hardware Qty Tools Needed
Wheels 2
Wheel cap 2
Pin roll 2
R-Pin Ø2 × 33
2
Support Leg 2
Flange bolt M8 × 45
4
2x 12mm wrench or
socket
Lock nut M8, flange 4
Detergent tank 1
Flange bolt M6 × 12
4
1x 10mm wrench or
socket
Detergent hose 1
Top handle 1
Trigger gun 1
Spray wand 1
Nozzle"0", 00025 1
Nozzle "15", 15025 1
Nozzle "25", 25025 1
Nozzle "40", 40025 1
Nozzle "Detergent", 65400 1
Trigger gun holder 1
Bolt M6 × 45
2 1x 10mm wrench
Lock nut M6, flange 2
High pressure hose, 25ft. 1
Hose strap 1
Engine oil, 0.6L 1
Oil Funnel 1
100783 - 3200 PSI PRESSURE WASHER
ASSEMBLY
12
ASSEMBLY
Your pressure washer requires some assembly. This unit ships
from our factory without oil. It must be properly serviced with
fuel and oil before operation. If you have any questions regarding
the assembly of your pressure washer, call our help line at
1-877-338-0999. Please have your serial number and model
number available.
Remove the Pressure Washer from the
Shipping Carton
1. Set the shipping carton on a solid, flat surface.
2. Remove everything from the carton except the pressure
washer.
3. Carefully cut each corner of the box from top to bottom.
Install Wheels, Support Legs, Detergent Tank,
Trigger Gun Holder, Handle, and Nozzles
Wheels
1. Before adding fuel and oil, carefully pivot the pressure washer
up and forward so that it rests on the front bumper housing.
Place a piece of cardboard from the packaging or moving
blanket on the ground before tipping forward.
2. Slide the roll pin through the wheel from the outside.
3. Slide the roll pin through the mount point on the frame.
4. Secure with the R-clip.
5. Repeat to attach the second wheel.
6. Add wheel caps to protect the roll pins.
Support Legs
1. Attach the supports legs to the pressure washer frame with
2 M8 x 45 flange bolts and 2 M8 flange lock nuts per leg.
Tighten to 8.8 ft-lb − 10.3 ft-lb (12-14 Nm).
2. Repeat to attach the second leg.
3. Slowly tip the pressure washer back down so that it rests on
the support legs.
Detergent Tank
1. Slide detergent tank from the back of the frame between the
support legs. It will only align one way. If for some reason,
you’re unable to align the tank holes to the brackets, reverse
out the tank and try the other way.
2. Attach to the frame with 2 M6 x 12 flange bolts on each side.
Tighten to 4.4 ft-lb − 5.9 ft-lb (6-8 Nm). Do not overtighten
and risk cracking the detergent tank.
100783 - 3200 PSI PRESSURE WASHER
ASSEMBLY
13
Trigger Gun Holder
1. Align the trigger gun holder to the frame.
2. Attach to the frame with 2 M6 x 45 flange bolts and M6
nuts. Tighten to 8.8 ft-lb − 10.3 ft-lb (12-14 Nm). Do not
overtighten.
Handle
1. Line up the handle with the bottom frame.
2. Make sure the handle holes are lined up with the bottom
frame spring button.
3. Slide the handle downward on the bottom frame, until the
spring buttons have popped through the holes on the handle
frame. A “click” may sound.
4. Gently pull up on the handle to make sure that two frames
have made a solid connection and that the handle cannot be
pulled off without pressing on the spring buttons to release it.
Nozzles
1. Nozzles are stored in the top panel. To store the nozzle, press
it into the corresponding opening. To remove the nozzle, just
pull the nozzle out.
High Pressure Hose Strap
The High pressure hose storage strap is provided to store your
hose when not in use. You can store the hose on the pressure
washer panel per below instructions or alternatively, use the strap
to hang it up on your shop peg board with provided handle on the
hose strap.
1. Feed hose strap end through the slot on the upper panel.
2. Coil up the hose up neatly and wrap the strap around the
hose.
3. Feed loose end (not handle-end on the hose strap) through
the slot of the handle on the hose strap and back again.
4. Attach hook side to loop side as tightly as necessary to hold
the hose during storage.
5. Your hose is now stored on your pressure washer.
6. For peg board or shop storage, start with step 2.
100783 - 3200 PSI PRESSURE WASHER
ASSEMBLY
14
Attach the Trigger Gun Assembly
1. Attach the spray wand to the trigger gun.
2. Rotate (clockwise) the M22 coupler on the trigger gun until
the spray wand is secure. Do not overtighten.
3. Connect the end of the high pressure hose to the gun inlet
by sliding back the metal collar on the female connector on
the high pressure hose. Insert male fitting (on the trigger
gun) and release collar. Gently tug on hose to ensure proper
connection.
NOTICE
Be careful to avoid cross-threading, which can cause the
trigger gun to leak during use.
Connect the High Pressure Hose
1. Completely uncoil and straighten the high pressure hose to
prevent kinks.
2. Align the male end of the high pressure hose to the quick
change connector on the high pressure pump.
3. Insert the high pressure hose connection into the pump quick
change fitting by sliding back the metal collar on the female
connector on the high pressure pump and fully insert male
fitting (on high pressure hose) and release collar.
4. Gently tug on hose to ensure proper connection.
NOTICE
Be careful to avoid cross-threading, which can cause the
trigger gun to leak during use.
5. Gently pull on the hose to be certain it is properly secured.
Connect the Garden Hose
The water supply must come from a pressurized water spicket.
NEVER use hot water or water from pools, lakes, etc. Before
connecting the garden hose to the pressure washer:
1. Run water through the hose for 30 seconds to clean any
debris from the hose.
2. Inspect the screen and gasket in the water intake.
3. If the screen and gasket is damaged, do not use the machine
until the screen has been replaced.
4. If the screen is dirty, clean it before connecting the garden
hose to the machine.
To connect the garden hose to the machine:
1. Completely uncoil the garden hose or remove completely from
reel to prevent kinks.
NOTICE
There must be a minimum of 10 ft. (3 m) of unrestricted hose
between the pressure washer intake and the hose faucet or
shut off valve (such as a “Y” shut off connector).
2. With the hose faucet turned completely off, attach the end of
the garden hose to the water inlet. Tighten by hand.
100783 - 3200 PSI PRESSURE WASHER
OPERATION
15
NOTICE
Do not run the pressure washer without water supply
connected and turned on, as this may damage the high
pressure seals and decrease pump life. Completely unwind the
hose from its reel or coil and make sure the hose is not being
restricted by tires, rocks, or any other objects that may lessen
or prevent water flow to the pressure washer.
Add Engine Oil
Refer to Honda’s engine owner/operator manual.
Add Fuel
Refer to Honda’s engine owner/operator manual.
OPERATION
Pressure Washer Location
This pressure washer must have at least 5 ft. (1.5 m) of clearance
from combustible material. Leave at least 3 ft. (91.4 cm) of
clearance on all sides of the pressure washer to allow for adequate
cooling, maintenance and servicing. Place the pressure washer in a
well ventilated area. DO NOT place the pressure washer near vents
or intakes where exhaust fumes could be drawn into occupied or
confined spaces. Carefully consider wind and air currents when
positioning pressure washer.
Before Starting the Engine
1. Turn the water supply ON.
2. Pull the trigger on the trigger gun to purge all air from the
pump and hose. This may take several minutes.
3. Do not start the engine until a steady stream of water is
flowing from the nozzle.
CAUTION
Never operate your pressure washer without water.
Starting the Engine
Refer to Honda’s engine owner/operator manual.
100783 - 3200 PSI PRESSURE WASHER
OPERATION
16
Distance from Cleaning Surface
The distance between the spray nozzle and the cleaning surface is another factor that affects the impact force of the water.
The impact force of the water increases as the nozzle is moved closer to the surface. You can vary the impact force by controlling
The nozzle’s fan pattern.
The nozzle’s angle to the cleaning surface.
The nozzle’s distance from the cleaning surface.
Never use a narrow high impact stream on a surface that is susceptible to damage. Avoid spraying windows with a narrow high impact
stream or turbo nozzle. Doing so may break the glass.
1. Before triggering the gun, select a nozzle with a wide fan pattern.
2. Place the nozzle approximately 4-5 ft. (1.2 m - 1.5 m) away from the cleaning surface. Then hold the nozzle at a 45 degree angle to
the cleaning surface. Trigger the gun.
3. Vary the fan pattern spray angle and the distance to the cleaning surface until optimum cleaning efficiency is achieved without
damaging the surface.
Use the following table to determine which nozzle to use.
NOZZLE SELECTION GUIDE
25°15° 40° Soap
GentleAbrasive
HIGH PRESSURE WASH
LOW
PRESSURE
WASH
15° 2 40° Soap
Concrete, Brick, Masonry
Siding, Gutters, Home
Fencing, Deck, Patio
Lawn and Garden Equipment,
Boats, RVs
Recommended nozzle Use with caution
100783 - 3200 PSI PRESSURE WASHER
OPERATION
17
NOTICE
Use only detergents designed for pressure washers.
Do not use household detergents, acids, alkalines, bleaches,
solvents, flammable material, or industrial grade solutions,
which can damage the pump or cause property damage. Many
detergents may require mixing prior to use. Prepare cleaning
solution as instructed on the solution bottle. Always test in an
inconspicuous area before beginning.
You can effectively clean surfaces by combining the chemical
action of detergents with high pressure rinses. On vertical
surfaces, apply the detergent starting at the bottom and work
your way upward. This method prevents the detergent from sliding
down and causing streaks. Begin high pressure rinsing at the
bottom and work your way upward. On particularly tough stains,
use a brush in combination with detergents and high pressure
rinsing.
1. Fill the detergent tank with cleaning solution.
2. Insert the detergent suction hose (end with the filter) through
the detergent tank cap until it goes all the way to the bottom
of the detergent tank.
3. Uncoil the rest of the detergent suction hose.
High Pressure Wash
CAUTION
Always engage the trigger safety latch when the unit is not in
use.
The trigger safety latch prevents the gun from being triggered
accidentally. Push the latch fully down to engage it.
WARNING
Injection hazard.
Fully unwrap and straighten high pressure hose prior to and
during each use and do not allow it to become kinked. The
high pressure hose features an outer covering that provides
strength to the hose. If the outer covering becomes damaged,
stop using the hose and replace it immediately. A kinked or
damaged hose can develop a high pressure leak and result in a
possible injection or other serious personal injury.
NOTICE
If the starter grip and rope becomes difficult to pull, squeeze
the trigger to relieve water pressure before attempting to start
the engine again.
For high pressure cleaning, refer to the Nozzle Selection Guide for
more information about which quick connect nozzle to choose.
CAUTION
The narrow high impact spray can damage some surfaces.
A wide fan pattern distributes the impact of the water over a larger
area resulting in excellent cleaning action with reduced risk of
surface damage. Clean large surface areas quickly using a wide
fan pattern.
Low Pressure Wash
Detergent Use
The use of detergents can dramatically reduce cleaning time
and assist in the removal of difficult stains. Many detergents are
customized for pressure washer use on specific cleaning tasks.
Pressure washer detergents are as thick as water.
Using thicker detergents – like dish soap – will clog the chemical
injection system.
100783 - 3200 PSI PRESSURE WASHER
OPERATION
18
To reduce the risk of bodily injury or property damage, always
follow this procedure whenever spraying is stopped, when work
is completed, and before checking or repairing any part of the
system.
1. Engage the trigger gun lock out.
2. Turn the unit off.
3. Shut off the water supply.
4. Disengage the trigger safety latch and trigger the gun to
relieve pressure.
5. Re-engage the trigger safety latch.
6. Before overnight storage, long term storage, or transporting
unit, disconnect the water supply and turn off the fuel supply
valve.
Operating Tips
CAUTION
Never operate your pressure washer without water.
CAUTION
Never connect your pressure washer to a hot water supply.
Connecting your pressure washer to a hot water source will
significantly reduce the life of the pump and will void the
warranty.
CAUTION
Running the unit for more than one minute without spraying
water causes heat to build up in the pump.
In the event that the pump gets too hot, a thermal relief valve
will open to release the hot water. Running the unit without
spraying water can damage pump components and will void
the warranty.
4. Connect the other end of the detergent suction hose to the
detergent barb on the pump.
WARNING
NEVER use bleach in detergent tank. It will damage the pump
and void the warranty.
NOTICE
The trigger gun will only draw detergent from the tank when
the black quick connect nozzle is installed in the wand.
NOTICE
When spraying detergent, the detergent will be diluted 1:12.
Approximately 20.3 oz. (0.6 L) of detergent will be consumed
from the tank for every minute sprayed.
System Flush
After using detergents, flush the suction system by placing the
detergent suction tube into a bucket of clean water.
WARNING
NEVER turn the water supply off before turning the engine off.
Depressurize System
To depressurize, turn engine off, turn water supply off and squeeze
gun trigger for at least 15 seconds after engine is turned off.
WARNING
NEVER disconnect the high pressure discharge hose from the
machine while the system is pressurized.
100783 - 3200 PSI PRESSURE WASHER
MAINTENANCE
19
Stopping the Engine
1. After stopping the engine per Honda’s owner/operator
manual, depressurize system by pressing the trigger gun to
release any trapped pressure.
2. Turn off water supply and disconnect all hoses.
Important: Always ensure that the fuel valve and the engine
switch are in the “OFF” position when the engine is not in use.
NOTICE
If the engine will not be used for a period of two (2) weeks or
longer, please see the Storage section for proper engine and
fuel storage.
Operation at High Altitude
Refer to Honda’s engine owner/operator manual.
MAINTENANCE
Make certain that the pressure washer is kept clean and stored
properly. Only operate the unit on a flat, level surface in a clean,
dry operating environment. DO NOT expose the unit to extreme
conditions, excessive dust, dirt, moisture or corrosive vapors.
WARNING
Never operate a damaged or defective pressure washer.
WARNING
Improper maintenance will void your warranty.
NOTICE
For Emissions control devices and systems, read and
understand your responsibilities for service as stated in the
Honda Engine Emission Control Warranty Statement of the
owner/operator’s manual.
The owner/operator is responsible for all periodic maintenance.
Complete all scheduled maintenance in a timely manner.
Correct any issue before operating the pressure washer.
For service or parts assistance, contact our help line at
1-877-338-0999.
For engine maintenance, refer to Honda’s engine owner/operator
manual.
Cleaning the Pressure Washer
CAUTION
DO NOT spray the pressure washer with water.
Water can contaminate the fuel system and can enter the
engine through the cooling slots and damage the engine.
1. Use a damp cloth to clean exterior surfaces of the pressure
washer.
2. Use a soft bristle brush to remove dirt and oil.
3. Use an air compressor (25 PSI) to clear dirt and debris from
the pressure washer.
4. Inspect all air vents and cooling slots to ensure that they are
clean and unobstructed.
Cleaning Spray Nozzle
Detach the quick connect nozzle from the wand. Use a small wire
rod (paper clip) to loosen up any particles in the quick connect
nozzle and flush with water.
To prevent accidental starting, remove and ground spark plug wire
before performing any service.
Changing the Engine Oil
Refer to Honda’s engine owner/operator manual.
Cleaning and Adjusting the Spark Plug(s)
Refer to Honda’s engine owner/operator manual.
Cleaning the Air Filter
Refer to Honda’s engine owner/operator manual.
Cleaning the Spark Arrester
1. If so equipped, allow the engine to cool completely before
servicing the spark arrester.
2. Refer to Honda’s engine owner/operator manual.
Maintenance Schedule
Refer to Honda’s engine owner/operator manual.
100783 - 3200 PSI PRESSURE WASHER
STORAGE
20
STORAGE
Refer to the Maintenance section for proper cleaning instructions.
Pressure Washer Storage
1. Allow the pressure washer to cool completely before storage.
2. Turn off the fuel supply at the fuel valve.
3. Clean the pressure washer according to the instructions in
the Maintenance section.
4. Store the unit in a clean, dry area out of direct sunlight.
Engine Storage
Refer to Honda’s engine owner/operator manual.
Winter Storage
Protect your pressure washer parts from freezing.
1. Apply all storage instructions from previous sections.
2. Make sure pressure washer hose is free of all water before
storing for winter.
3. In order to prevent the pump from freezing you will need to
insert RV antifreeze.
4. You will need approximately 6 oz. (177.4 mL) of RV antifreeze,
a funnel, and approximately 12 in. (30.5 cm) of garden hose
or equivalent.
5. Pour the antifreeze into the funnel connected to the pump
inlet with a small hose, then pull on the recoil starter to create
suction in the pump housing. Pull the recoil several times until
antifreeze comes out of the pump outlet.
WARNING
Never store the pressure washer inside or next to appliances
where there is a source of heat or open flame, spark or pilot
light because they can ignite gasoline vapors.
DO NOT store a pressure washer near fertilizer or any
corrosive material.
Even with an empty gas tank, gasoline vapors could ignite.
DANGER
Engine exhaust contains odorless and colorless carbon
monoxide gas.
To avoid accidental or unintended ignition of the product
during periods of storage, the following precautions should be
followed:
When storing the pressure washer for short or long periods
of time make sure that the engine switch and the fuel valve
are set in the "OFF" position.
SPECIFICATIONS
Pressure Washer Specifications
Model ....................................................... 100783
Max Pressure .............................................. 3200 PSI
Max Volume ................................................2.5 GPM
Max Water Temperature (°F/°C) ............................ 104/40
Weight ................................................ 62 lb. (28 kg)
Length .......................................... 41.5 in. (105.4 cm)
Width ............................................ 19.5 in. (49.5 cm)
Height ............................................. 27.1 in. (68.9 cm)
Engine Specifications
Refer to Honda’s engine owner/operator manual.
Spark Plug
Refer to Honda’s engine owner/operator manual.
Valve
Refer to Honda’s engine owner/operator manual.
Oil Specifications
Refer to Honda’s engine owner/operator manual.
Fuel Specifications
Refer to Honda’s engine owner/operator manual.
Temperature Specifications
Refer to Honda’s engine owner/operator manual.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

Champion Power Equipment Pressure Washer Manuel utilisateur

Catégorie
Nettoyeurs haute pression
Taper
Manuel utilisateur
Ce manuel convient également à