Caloric CVU306C-SS Le manuel du propriétaire

Marque: Caloric

Modèle: CVU306C-SS

Catégorie: Hottes

Taper: Le manuel du propriétaire

UNDER-MOUNT HOOD / HOTTE SOUS-CABINET

MODEL / MODÈLE: CVU306C-SS

INSTRUCTIONS D’INSTALLATION ET GUIDE DE L’USAGER

INSTALLATION GUIDE / USE AND CARE MANUAL

Installer: Leave this manual with the homeowner.

Homeowner: Keep this guide for future reference.

Installateur : Laissez ce manuel au propriétaire.

Propriétaire : Conservez ce guide pour référence ultérieure.

2020A

IMPORTANT: Read and save these instructions.

IMPORTANT: Lire et conserver ces instructions.

Table of Contents

IMPORTANT SAFETY PRECAUTIONS ............................................... 3-4

INSTALLATION INSTRUCTIONS ................................................... 5-12

OPERATING THE HOOD ................................................................ 13

MAINTENANCE ............................................................................ 15

WARRANTY ................................................................................. 17

APPROVED FOR APPLIANCES OF RESIDENTIAL USE

ONLY. READ AND SAVE THESE

INSTRUCTIONS.

PLEASE READ THE ENTIRE INSTRUCTIONS BEFORE YOU

BEGIN. INSTALLATION OF THE UNIT MUST RESPECT

ALL CODES.

IMPORTANT: Keep these instructions in order to provide them to the electrical inspector

in your area.

INSTALLER: Please leave these instructions with the owner of the unit.

OWNER: Keep these instructions for future reference.

SECURITY WARNING: Turn off the power circuit in the electrical panel and lock the

front panel before connecting the wires of this unit.

Requirements: 120V c.a., 60Hz branch circuit of 15V c.a., 20Hz, of 15 or 20A

IMPORTANT SAFETY PRECAUTIONS

READ AND SAVE THESE

INSTRUCTIONS CAUTION

For residential use only. Do not use to exhaust hazardous or explosive materials and/or vapors.

CAUTION

Range hood may have very sharp edges; please wear protective gloves when installing, cleaning

or servicing the unit.

This appliance must be installed by a qualified technician. The manufacturer declines all

responsibility in case of failure to adhere to safety standards. Install this hood in accordance with

all the specified requirements.

WARNING

To reduce the risk of fire, electric shock or injury to persons, observe the following:

• Use this unit only in the manner intended by the manufacturer. If you have any questions,

contact the manufacturer.

• Before servicing or cleaning the unit, switch power off at the service panel and lock the service

disconnecting means to prevent power from being switched on accidentally. If the service

disconnecting means cannot be locked, securely fasten a noticeable warning device, such as a

tag, to the service panel.

• Installation work and electrical wiring must be done by a qualified person in accordance with

all applicable codes & standards, including Fire-rated construction.

• Sufficient air is needed for proper combustion and exhausting of gases through the chimney

(chimney) of fuel burning equipment to prevent back-drafting.

• Follow the heating equipment manufacturer’s guideline and safety standards such as those

published by the National Fire Protection Association (NFPA) and the local code authorities.

• When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

• Ducted fans must always be vented to the outdoors.

• Do not make alterations to the original wiring.

• Do not attempt to repair or replace any part of your hood unless it is specifically

recommended in this manual.

• All other servicing issue should be referred to a qualified technician.

CAUTION:

To reduce risk of fire and to properly exhaust air, be sure to duct air outside - do not vent exhaust air into

spaces within such as walls, ceilings, attics, crawl spaces, or garages.

Automatically operated device - to reduce risk of injury disconnect from power supply before servicing.

WARNING

TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.

WARNING

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

• Never leave a range unattended.

• Boil-overs cause smoke and greasy spillovers that may ignite. Heat oils slowly on low or medium setting.

• Always turn hood ON when cooking at high heat or when flambéing food (i.e. Crepes Suzette,

Cherries Jubilee, Flambés, etc. …).

• Clean the unit’s surfaces frequently. Grease can accumulate on fan or filters.

• Use proper pan size. Always use cookware appropriate for the size of the cooking element.

WARNING

TO REDUCE THE RISK OF INJURY TO PERSONS, IN THE EVENT OF A COOKTOP GREASE FIRE,

OBSERVE THE FOLLOWING:

• Smother flames with a close-fitting lid, cookie sheet, or metal tray and then turn off the burner.

• If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.

• Never pick up a flaming pan - you may BURN YOURSELF.

• DO NOT USE WATER, including wet dishcloths or towels -a violent steam explosion will result.

• Use an extinguisher ONLY if:

a) You know you have a class ABC extinguisher, and you already know how to operate it.

b) The fire is small and contained in the area where it started.

c) The fire department has been called.

d) You can fight the fire with your back to an exit.

INSTALLATION INSTRUCTIONS

TOOLS NEEDED TO INSTALL THE RANGE

HOOD

▪ Safety gloves and goggles

▪ Electrical drill

▪ Phillips screwdriver

▪ Flathead screwdriver

▪ Adjustable wrench

▪ Utility knife

▪ Scissors (to cut duct tape)

▪ Aluminum duct tape

▪ Marker or pencil

▪ Level

▪ Measuring tape

PARTS INCLUDED

Baffle filters Top cover for square exhaust connector

6" adapter for vertical evacuation 3.25" x 10" Adapter for horizontal evacuation

Qty: 6 pcs

(for drywall only)

DIMENSIONS OF HOOD

INSTALLATION

The information contained herein is based on sources that we believe to be reliable, but is not

guaranteed by us, may be incomplete and/or may change without notice.

Floor to ceiling height

variable

Floor to counter top height

(standard)

36"

Recommended height between

cooking surface and bottom of the

hood

28"-30"

Hood height

Cabinet height

N/A

Hood

Duct transitions

6" round-top

3.25" x 10" rear

BEFORE INSTALLING THE HOOD

▪ For the most efficient airflow exhaust, use a straight run or as few elbows as possible.

▪ Vent unit to the OUTSIDE only.

▪ At least two people are required for installation.

▪ Remove the range hood from the carton packaging and place on a flat surface for assembly.

CAUTION

THIS APPLIANCE SHOULD BE PROPERLY GROUNDED.

▪ This hood has two types of electrical connection:

▪ A connection with electric wires

▪ 3-wire power outlet, 120V 60Hz (supplied but not installed).

▪ Make sure the unit is connected to an individual, properly grounded circuit.

▪ If the electrical supply does not meet above requirements, call a licensed

electrician before proceeding.

▪ Route house wiring as close as possible to the installation location, in the ceiling or back wall.

▪ The hood must be connected to the house wiring in accordance with the local codes and norms.

WALL FRAMING FOR ADEQUATE SUPPORT

THIS VENT HOOD IS HEAVY. ADEQUATE STRUCTURE AND SUPPORT MUST BE PROVIDED IN ALL TYPES

OF INSTALLATION. IF MOUNTING ONTO DRY WALL, IT IS RECOMMENDED THAT THE HOOD BE SECURED

TO VERTICAL STUDS IN THE WALL OR TO A HORIZONTAL SUPPORT.

WARNING

BE CAREFUL WHEN INSTALLING THE HOOD, AS IT MAY HAVE SHARP EDGES. WE RECOMMEND THAT YOU

WEAR PROTECTIVE GLOVES.

CAUTION

DO NOT REMOVE THE PROTECTIVE PLASTIC FILM COVERING THE HOOD AT THIS STAGE.

Venting Requirements Height & Clearance

•

Vent system must evacuate to the

exterior – Outside (through the

roof or side wall).

•

DO NOT terminate the vent system in

an attic or other enclosed area.

•

Use rigid metal/aluminum vent only.

•

NEVER use plastic vent or plastic vent cover.

•

Always keep the duct clean to

ensure proper airflow.

•

Calculate the following figures before installation:

1. Distance from the floor to the ceiling.

2. Distance between the floor and

the countertop/cooking element.

3. Distance between the range hood

and the countertop/cooking

element which is recommended

at 28” to 30’’.

4. Height of hood and duct cover

with the cabinet.

For the most efficient & quiet operation:

•

It is recommended that the range

hood be vented vertically through the

roof through 6” (15.3 cm) round

metal/aluminum vent or vented

horizontally through the wall through

a rectangular vent measuring 3 ¼’’ x

10’’.

•

The size of the vent should be uniform.

•

If venting vertically, do not use more

than three 90° elbows. Do not install

two elbows together.

•

Make sure there is a minimum of 24”

(61 cm) of straight vent between the

elbows if more than one elbow is

used.

•

The length of vent system and number

of elbows should be kept to a

minimum to provide efficient

performance.

•

The vent system must have a damper.

If roof or wall cap has a damper, DO

NOT use damper (which is supplied)

on top of the range hood.

•

Use duct tape to seal all joints in the

vent system.

•

Use caulking to seal the exterior wall

or roof opening around the cap.

Cabinet

height

Cabinet

Range

hood

height

Range hood

Ceiling

height

Min: 28”

Max: 30”

Countertop/

Cooking element

36” standard

counter

height

IMPORTANT

•

A rectangular duct of 3 ¼’’ x 10 ‘’ or a round duct of a minimum of 6” (standard for this range hood)

must be used to maintain maximum airflow efficiency.

•

Always use rigid type metal/aluminum ducts if available to maximize airflow when connecting to

duct provided.

VENTING METHODS

INSTALLATION DIAGRAMS

•

Vent work can terminate either through the roof or wall. To vent through a wall, a 90° elbow may

be needed.

•

This range hood is factory set for vertical venting using round or rectangular vent adapter but can

be converted to horizontal venting by swapping the round vent adapter on top with rectangular

vent adapter behind the range hood as shown below:

Type 3:

6’’ round vent adapter on the

top of the range

hood.

Option 1:

Horizontal venting

Wall cap

Option 2:

Vertical venting

Roof cap

Type 1:

3 ¼’’ x 10’’ rectangular vent adapter

behind the range hood.

Type 2:

¼’’

x 10’’ rectangular vent adapter on

top of the range hood.

ELECTRICAL REQUIREMENTS AND

INSTALLATION WARNING

THIS RANGE HOOD MUST BE PROPERLY GROUNDED. TURN OFF ELECTRICAL POWER AT SERVICE ENTRANCE

BEFORE WIRING. CHECK TO MAKE SURE THAT THE ELECTRIC CORD IS NOT IN CONTACT WITH THE SHARP

EDGES OF THE APPLIANCE.

IMPROPER GROUNDING CAN RESULT IN A RISK OF ELECTRIC SHOCK. CONSULT A QUALIFIED ELECTRICIAN

IF THE GROUNDING INSTRUCTIONS ARE NOT COMPLETELY UNDERSTOOD OR IF THERE IS DOUBT AS TO

WHETHER THE APPLIANCE IS PROPERLY GROUNDED. DO NOT USE AN EXTENSION CORD. IF THE POWER

SUPPLY CORD IS TOO SHORT, HAVE A QUALIFIED ELECTRICIAN INSTALL AN OUTLET NEAR THE APPLIANCE.

•

This appliance must be plugged into an outlet that is properly installed and grounded. In the event

of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape

wire for the electric current.

•

Position the outlet offset so that the power cord will not interfere with the duct.

ADVANCED PREPARATION

•

Decide on the location of the venting pipe from the hood to the outside.

•

A straight, short vent run will allow the hood to perform more efficiently. Try to avoid as many

transitions, elbows and long runs as possible. This may reduce the hood’s performance.

•

Use duct tape to seal joints between pipe sections.

•

For installing under the cabinet with recessed bottom, attach 4’’ wide wood filler strips (not

provided) on each side. See Figure 1.

•

Using references in measurements and installation diagrams (see pages 21 and 22), create access

opening for electrical wires and hood exhaust under the cabinet.

CAUTION: If moving the cooking range to install the hood, turn OFF the power at the main electrical box.

SHUT OFF THE GAS BEFORE MOVING A GAS RANGE.

•

Puncture the knockout holes (for mounting under the cabinet) on the hood as shown in Figure 2.

•

If necessary, attach two rubber stands with adhesive tapes to the back corners of the hood.

Three or more persons are required to move and install

this range hood. Spinal or other bodily injuries may occur

if these instructions are not followed.

Risk of severe injury

Rotating fan can cause severe injury.

Stay clear of fan when motor is running.

Figure 1

Figure 2

CABINET CUT-OUT (seen from the top)

CABINET CUT-OUT (seen from the rear)

centerline

Mounting screws

Electrical Access -

Opening

Rear duct access

Wood filler support

strips

(not included)

Top duct

/exhaust

access

Mounting

screw

attachment

WALL

Electrical Access -opening

centerline

INSTALLATION

Measure the distance between the cooking

element and the bottom of the range hood.

A distance of 28” to 30” is recommended*.

* Due to different ceiling height configurations,

the recommended height may not be

applicable.

Step 1: You have two options for installing this range hood (see INSTALLATION DIAGRAMS on page 22).

Determine the venting method and proceed as follows:

1. Using references in the Height & Clearance diagram, determine and clearly mark the

centerline on the bottom of the cabinet.

2. Draw electrical wires through cabinet access opening on top or back of the range hood,

center the hood beneath the cabinet and flush with the front of the cabinet.

3. From the inside of the hood, place hood mounting screws in the exact center of each

knockout holes and secure to the cabinet bottom. Tighten all screws until secure. Be

careful when using electrical screwdriver in order not to damage the range hood. If

venting is to be done vertically, connect and secure the 6’’ round metal duct (refer to figure

1).

CAUTION: Make certain the range hood is secure before releasing!

Step 2:

For safety purpose, pre-drilled mounting holes are provided through the back of the hood. For a

more secure installation, use as many mounting holes as needed to secure the hood from the inside.

In the case of vertical evacuation use a 6” round metal pipe (as in figure 1) to connect the exhaust on the

hood to the ductwork. Use duct tape to make all joints secure and airtight.

Step 3: Turn power ON in control panel. Check all lights and fan operations.

Figure 1

RANGE HOOD OPERATIONS

3-Speed Electronic Touch Control

This range hood is built to eliminate fumes, smoke, odors and steam from the air by evacuating

them outside. For best results, start the range hood before cooking and allow it to operate

several minutes after cooking is completed to help clear all smoke and odors from the kitchen.

Butto

ns:

Power button: To turn ON/OFF the range hood and activate Power-off Delay Timer.

Decrease value button: To decrease blower (motor) speed, to decrease timer and to

enter timer mode.

Increase value button: To increase blower speed, to increase timer and to reset

cumulative timer.

Clock / Digital Display button: To display current time when motor is OFF.

Shows current blower (motor) speed (F1-F3).

Light button: To turn the lights ON/OFF.

Controls:

To adjust the blower (motor) speed: Press Power button once to turn on the system.

The Digital Display will show the blower (motor) speed level. Pressing the Decrease button

will decrease the speed of the blower (motor) from F3 to F1 (strongest to quietest).

Pressing the Increase button will increase the speed of the blower (motor) from F1 to F3

(quietest to strongest).

Power

Power off delay

Decrease

Light

Increase

Clock /digital display

OPERATING THE HOOD (continued)

Controls (continued):

Adjusting the Power-Off / 3-minute Delay Timer function: While the motor is running,

press the Power button once to enter Power-Off Delay Timer mode, the digital display

will flash and blower (motor) will turn off after three (3) minutes. During the 3-minute delay,

changing speeds will

not affect the countdown. You can cancel the 3-minute Power-Off Delay Timer function by

pressing Power button once.

Immediate Power-Off: When the blower is operational in normal mode (Power-Off Delay Timer

inactivated), rapidly press the Power Control (On/Off) button twice to turn off the blower

(motor).

Lights: Press the Light button once to turn on the lights and once again to turn off the lights.

Adjusting the clock: When the blower (motor) is off, press and hold Power button

to enter the clock setting. Press Increase Value & Decrease Speed buttons to adjust the

hour and

press the Power button again to adjust the minutes by pressing Increase Value & Decrease

buttons . The system will automatically exit the clock-setting mode after three (3) seconds.

Note: The system saves the user's configurations. Settings such as light, timer and fan speed

will stay the same the next time.

MAINTENANCE

SAFETY WARNING: NEVER PUT YOUR HAND INTO AREA HOUSING THE FAN

For optimal operation, clean range hood and filters regularly. Regular care will help preserve the

appearance of the range hood.

CLEANING THE SURFACES

Clean periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent

or steel wool pads, which will scratch and damage the stainless-steel finish. For heavier soil, use a liquid

degreasing cleaner. Use a stainless-steel cleaner to clean the surfaces of the hood. Avoid getting cleaning

solution onto or into the control panel. Follow directions of the stainless-steel cleaner.

CAUTION

USE SOFT TOWEL TO WIPE OFF THE CLEANING SOLUTION, GENTLY RUB OFF ANY STUBBORN SPOTS. USE DRY SOFT

TOWEL TO DRY THE HOOD. ALWAYS SCRUB LIGHTLY WITH CLEAN COTTON CLOTH AND IN THE DIRECTION OF THE

GRAIN.

DO NOT ALLOW DEPOSITS TO ACCUMULATE OR REMAIN ON THE HOOD. DO NOT USE ORDINARY STEEL WOOL OR

STEEL BRUSHES. SMALL BITS OF STEEL MAY ADHERE TO THE SURFACE AND CAUSE RUSTING.

DO NOT ALLOW SALT SOLUTIONS, DISINFECTANTS, BLEACHES OR CLEANING COMPOUNDS TO REMAIN IN

CONTACT WITH STAINLESS STEEL FOR EXTENDED PERIODS. MANY OF THESE COMPOUNDS CONTAIN CHEMICALS,

WHICH MAY BE HARMFUL. RINSE WITH WATER AND WIPE DRY WITH A CLEAN CLOTH.

CLEANING THE GREASE FILTER

The filters are intended to filter out residue and grease from cooking and are required to be kept clean.

Filters should be cleaned after every 30 hours of use (or once a month, depending on use). Remove and

clean by hand in soapy water or in the dishwasher. Dry filters and re-install. If cleaning the filters in the

dishwasher, use a non- phosphate detergent. The use of detergent with phosphate may cause

discoloration of the filters, but will not affect their performance. This discoloration is not covered by the

warranty.

REPLACING THE FILTERS

If filters wear out due to prolonged use, please contact your service/parts provider for replacement filters.

NOTE: ALSO REPLACE DAMAGED FILTER THAT HAS PUNCTURED OR BROKEN MESH, BENT OR BROKEN FRAME.

CLEANING THE STAINLESS-STEEL SURFACES

Regularly wash surfaces with dry cloth or clean cloth soaked in warm water and mild soap or liquid dish

detergent. Always clean following the grain. Always rinse thoroughly with clear water (2-3 times) and wipe

dry completely. Specially designed stainless-steel cleaners can also be used.

REPLACING THE LED LIGHT BULBS

Cut the power supply by turning the hood off. Wait for the LED lamps to cool. To prevent damage or to

avoid reducing the life of the new bulb, do not touch the bulb with your bare fingers. Replace the bulb by

manipulating with a tissue paper or cotton gloves.

If the new lights do not work, ensure that each lamp is properly inserted into its socket before requesting

the intervention of a service agent.

MAINTENANCE (continued)

REPLACING THE LED LIGHT BULBS (

CONTINUED)

CAUTION: LED lamps can only be replaced with a new LED lamp. The lamp rating must be equal to the

one already used. Make sure all the control switches are off and the hood is unplugged or that the

breaker is OFF.

STEPS :

•

This range hood uses LED light fixture: 3W Max 12V LED

•

Make sure the range hood is unplugged or turn OFF the breaker. Make sure the lights are cool to touch.

•

Place a flat-head screwdriver between the light housing and the hood body, gently pry up the light

housing and search for the metal clip.

•

Apply force to the metal clip and pull out the light fixture. Disconnect the power cable and

discard the used light fixture.

•

Reverse the steps to install a new LED light fixture. Turn the breaker or hood ON to test for operation.

SERVICE AND WARRANTY

LIMITED WARRANTY

This warranty applies only to the original purchaser and may not be transferred. This warranty is

applicable within Canada only, to hoods installed for normal, non-commercial use in PRIVATE SINGLE-

FAMILY HOUSEHOLDS.

Caloric™ warrants this product to be free from defects in material or workmanship for a period of ONE YEAR from

the date of original purchase. During the warranty period, Caloric™ will, at its option, repair or replace, without

charges, any product or part which is found to be defective under normal use and service. This warranty covers parts

and labour from a Caloric™ authorized company, up to a maximum of one (1) hour. Proof of payment to the service

company is required.

THERE ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, IMPLIED

WARRANTIES OR MERCHANT ABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Proof of purchase/original invoice and serial number is required for warranty claims. Keep a photocopy easily

accessible.

This warranty will be void if the serial plate has been removed or disfigured.

EXCLUSIONS – This Caloric™ warranty does not cover: • Aluminum or SS baffle filters, lights or glass canopies,

blower wheel damage • Regular maintenance and service (except by an authorized Caloric ™ repair center) •

Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation

not in accordance with electrical codes, or use of consumables or cleaning products not approved by Caloric™ •

Repair of an appliance used in other than a normal, single-family household, or in a manner that is contrary to the

operation or installation instructions. • Cosmetics damage or freight damage caused by a 3rd party freight company.

• Service to product that is not easily accessible due to unusual, exceptional, or difficult installation • Service calls to

instruct how to use the appliance • Expenses for travel and transportation if your appliance is in a remote area where

service by an authorized Caloric™ servicer is not available.

The cost of repair or replacement under these exclusions shall be borne by the customer and agreed to before a

servicer is dispatched.

Caloric™ SHALL NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING

OUT OD OR IN CONNECTION WITH PRODUCT USE OR PERFORMANCE.

For a Caloric™ authorized repair center please contact us at:

1-844-455-3474 ext. 2 or service@caloricappliances.ca

We do the utmost to ensure that the provided information is complete and accurate, however, images and

specifications are subject to change without notice. Visit our website at www.caloricappliances.ca for the latest

version of this manual.

In Canada CALORIC™ is a registered trademark of J.A.K. North America Inc.

Table des matières

IMPOPTANTES MESURES DE SÉCURITÉ ........................................ 19-20

INSTRUCTIONS D’INSTALLATION ................................................ 21-28

MODE D’EMPLOI ........................................................................... 29

ENTRETIEN .................................................................................. 30

SERVICE ET GARANTIE ................................................................... 32

APPAREILS APPROUVÉS POUR UTILISATION RÉSIDENTIELLE

SEULEMENT. LISEZ CES INSTRUCTIONS ET CONSERVEZ-LES

VEUILLEZ LIRE CES INSTRUCTIONS AU COMPLET AVANT DE

COMMENCER. L’INSTALLATION DE L’APPAREIL DOIT RESPECTER TOUS

LES CODES LOCAUX/NATIONAUX EN VIGUEUR.

IMPORTANT

: Conservez ces instructions afin de pouvoir les remettre à

l’inspecteur- électricien de votre région.

INSTALLATEUR : Veuillez laisser ces instructions avec l’appareil pour le propriétaire.

PROPRIÉTAIRE : Veuillez conserver ces instructions pour pouvoir vous y référer plus tard.

AVERTISSEMENT DE SÉCURITÉ : Coupez l’alimentation du circuit dans le panneau électrique

et verrouillez le panneau avant de raccorder les

fils de cet appareil.

Exigence : 120V c.a., 60Hz circuit de dérivation de 15V c.a., 20Hz, de 15 ou 20A

MESURES DE SÉCURITÉ IMPORTANTES

AVERTISSEMENT

Pour usage domestique seulement. Ne pas utiliser pour évacuer des vapeurs ou des matières

dangereuses ou explosives.

ATTENTION

Cette hotte peut avoir des bords très tranchants ; veuillez porter des gants de protection lors de

l'installation, du nettoyage ou de l'entretien de l'appareil.

Cet appareil doit être installé par un technicien qualifié. Le fabricant décline toute responsabilité en cas de

défaut de se conformer aux normes de sécurité. Installez cette hotte en respectant toutes les

exigencesspécifiées.

AVERTISSEMENT

Afin de réduire les risques d’incendie, d’électrocution ou de blessures corporelles, suivez les directives suivantes :

▪ N’utilisez cet appareil que de la façon prévue par le manufacturier. Si vous avez des

questions, contactez le manufacturier à l’adresse ou au numéro de téléphone indiqué

dans la garantie.

▪ Avant de réparer ou de nettoyer l’appareil, coupez l’alimentation électrique en

verrouillant le panneau électrique afin d’éviter sa remise en marche accidentelle. Si le

panneau électrique ne peut pas être verrouillé, fixez-y un avertissement bien en

évidence telle qu’une étiquette de couleur vive.

▪ Les travaux d’installation et de raccordement électriques doivent être effectués par une

personne qualifiée, conformément aux codes et aux standards de construction, incluant

ceux concernant la protection contre les incendies.

▪ Laissez une quantité suffisante d’air afin d’assurer une bonne combustion ainsi que

l’évacuation des gaz par la cheminée (dans le cas des équipements alimentés au gaz) afin

de prévenir les retours de cheminée.

▪ Conformez-vous aux instructions et aux standards de sécurité des manufacturiers

d’équipement de chauffage ainsi que les codes et standards locaux.

▪ Veillez à ne pas endommager le câblage électrique ou d’autres équipements non

apparentslors de la découpe ou du perçage du mur ou du plafond.

▪ Les ventilateurs avec conduits doivent toujours évacuer l’air vers l’extérieur.

▪ Ne faites pas de modifications au câblage d'origine.

▪ N'essayez pas de réparer ou de remplacer quelque pièce que ce soit de votre hotte, sauf

s'il est spécifiquement recommandé dans ce manuel.

▪ Toutes les autres réparations devraient être effectuées par un technicien qualifié.

AVERTISSEMENT

Afin de réduire les risques d’incendie, assurez-vous d’évacuer l’air vers l’extérieur. Ne pas évacuer

l’air dans des espaces restreints comme l’intérieur des murs, du plafond, le grenier, faux plafond ou

garage.

Dispositif automatique - pour réduire les risques de blessures, débranchez l’appareil avant d’en

effectuer l'entretien.

AVERTISSEMENT

AFIN DE RÉDUIRE LES RISQUES D’INCENDIE, N’UTILISEZ SEULEMENT QUE DES CONDUITS DE MÉTAL.

AVERTISSEMENT

AFIN DE RÉDUIRE LES RISQUES DE FEU DE CUISINIÈRE :

▪ Toujours mettre la hotte en marche lorsque vous cuisinez.

▪ Ne jamais laisser les appareils de cuisson sans surveillance lorsqu’ils sont réglés à feu

vif. Les débordements engendrent de la fumée et des déversements graisseux qui

pouvant s’enflammer. Chauffez l’huile lentement, à feu doux ou moyen.

▪ Il est essentiel d’avoir la hotte en marche lorsque vous cuisinez à feu vif ou que vous

cuisinez des mets flambés (par ex. : Crêpes Suzette, Cerises jubilées, Steaks au

poivre flambés,etc.).

▪ Nettoyez régulièrement la (les) palme (s) du ventilateur. Ne pas laisser la graisse

s’accumuler sur le ventilateur, les filtres ou les conduits d’évacuation.

▪ Utilisez le bon format de casserole. Servez-vous toujours de casseroles et

d’ustensiles appropriés à la dimension de la surface de cuisson.

AVERTISSEMENT

AFIN D’ÉVITER TOUT RISQUE DE BLESSURES LORS D’UN FEU DE CUISINIÈRE, SUIVEZ CES DIRECTIVES

▪ Étouffez les flammes avec un couvercle hermétique, une tôle à biscuits ou

un plateau métallique et ensuite éteindre le brûleur.

▪ Si les flammes ne s’éteignent pas immédiatement, ÉVACUEZ LES LIEUX ET

APPELEZ LES POMPIERS.

▪ Ne prenez jamais une casserole en flamme dans vos mains. Vous pourriez vous brûler.

▪ N’UTILISEZ PAS D’EAU, y compris un linge à vaisselle ou une serviette mouillée car cela

pourrait occasionner une violente explosion de vapeur.

▪ N’utilisez un extincteur QUE DANS LE CAS OÙ :

a) Vous savez qu’il s’agit d’un extincteur de classe ABC et que vous en

connaissez le fonctionnement.

b) L’incendie est petit et limité à l’endroit où il a débuté.

c) Les pompiers ont été avisés.

d) Vous pouvez combattre l’incendie en ayant accès à une sortie de secours.

La page charge ...

Caloric CVU306C-SS Le manuel du propriétaire

Marque: Caloric

Modèle: CVU306C-SS

Catégorie: Hottes

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Caloric CVU306C-SS Owner's manual

Caloric CVU306C-SS Le manuel du propriétaire

Caloric CVU306C-SS Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents