Crosley CDB350NB7B Le manuel du propriétaire

Crosley
Marque
Crosley
Modèle
CDB350NB7B
Catégorie
Lave-vaisselle
Taper
Le manuel du propriétaire

Ce manuel convient également à

TA B L E O F C O N T E N T S
www.crosley.com USA and Canada 1-336-761-1212
All about the
Use & Care
of your Dishwasher
Crosley
®
Important Safety Instructions ......................2
Product Registration ...................................3
Features at a Glance ...................................4
Operating Instructions .............................5-6
Preparing and Loading Dishes ..................7-9
P/N A04802201RevB Artwork A04802201Rev002 (May 2016)
Factors Affecting Performance ...................11
Care and Cleaning ....................................12
Before you Call .................................... 13-15
Major Appliance Warranty .........................16
Dishwasher Dispenser and Detergents .......10
WARNING
This symbols will help alert you to such
dangers as personal injury, burns, fi re and
electrical shock.
WARNING
To reduce the risk of fi re, electrical shock or
injury when using your dishwasher, follow
the above basic precautions.
2
IMPORTANT SAFETY INSTRUCTIONS
For your Safety
• Use your dishwasher only as instructed in
this Use and Care Manual.
• This Manual does not cover every possible
condition and situation that may occur.
Use common sense and caution when
installing, operating and maintaining any
appliance.
• NSF certifi ed residential dishwashers
are not intended for licensed food
establishments.
• DISHWASHER MUST BE ELECTRICALLY
GROUNDED. Read the Installation
Instructions for details.
WARNING
Please read all instructions before using this
dishwasher.
• This dishwasher is designed to operate on
regular house current (120V, 60Hz). Use
a circuit equipped with a 15 ampere fuse
or circuit breaker. Use a 20 ampere fuse
if dishwasher is connected with a food
disposer.
• Do not operate dishwasher unless all
enclosure panels are in their proper place.
• To avoid entrapment and/or suffocation,
remove door or door latch mechanism from
any dishwasher that is discarded or not in
use.
• Keep young children and infants away from
dishwasher when it is operating.
• Do not let children abuse, sit, stand or play
on door or racks of a dishwasher.
• Use only detergents and rinse agents
recommended for use in a dishwasher.
• Store dishwasher detergent and rinse
agents out of the reach of children.
• Do not wash plastic items unless marked:
“Dishwasher Safe” or equivalent. Check
with manufacturer for recommendations,
if not marked. Items that are not marked
dishwasher safe may melt and create a
potential fi re hazard.
• Disconnect electrical power to dishwasher
before servicing.
• If the dishwasher drains into a food
disposer, make sure disposer is completely
empty before running dishwasher.
• Repairs should be done by a qualifi ed
technician.
• Do not tamper with controls.
• Do not touch the heating element during or
immediately after
• Use care unloading the dishwasher when
the SANITIZE option has been selected.
Contents may be hot to the touch
immediately after the end of cycle.
• Water vapor from the vent may be hot to
the touch when the SANITIZE option has
been selected. Use care and do not let
small children play around or touch the
vent area of the dishwasher.
• When loading items to be washed:
• Locate sharp items and knives so that
they are not likely to damage the door
seal or tub.
• Load sharp items and knives with the
handles up to reduce the risk of cut-type
injuries.
• Under certain conditions, hydrogen gas
may be produced in a hot water, system
that has not been used for 2 weeks or
more. HYDROGEN GAS IS EXPLOSIVE. If
hot water system has not been used for
such a period, before using dishwasher,
turn on for several minutes This will
release any accumulated hydrogen gas.
HYDROGEN GAS IS FLAMMABLE. Do not
smoke or use an open fl ame during this
time.
• Do not store or use combustible materials,
gasoline or other fl ammable vapors and
liquids in the vicinity of this or any other
appliance.
3
PRODUCT REGISTRATION
NOTE
Thank you for choosing Crosley
This Use & Care Guide is part of our
commitment to customer satisfaction and
product quality throughout the service life of
your new appliance.
We view your purchase as the beginning of a
relationship. To ensure our ability to continue
serving you, please use this page to record
important product information.
_________________________________
Purchase Date
_________________________________
Model Number
_________________________________
Serial Number
ë
Very Important Information
- Read Before Operating Your
Dishwasher!
Normal Operating Sounds
This dishwasher does not sound like most
dishwashers - IT’S QUIETER.
Your Precision Direct Wash System
®
dishwasher
uses energy effi cient motors for the wash and
drain portions of the cycle you select. Each
cycle has a series of water fi lls and drains for
washing and rinsing dishes. As each cycle
begins, you may - or may not - hear the drain
motor.
The next sound you will hear is the splashing
water as it enters the tub. Then the lower arm
rotates and circulates water. This is followed
by a pause and a slightly different sound as the
upper arms spray water. If you listen closely,
you will hear the change in sound as the wash
action switches from one arm to the other.
PLEASE BE ADVISED: If you compare
this dishwasher to previous models,
you may be surprised at what you
DON’T hear.
CAUTION
Property Damage Hazard
Before starting dishwasher be sure that the
water is connected and turned on. Failure to
do so may cause damage to the pump seal
and result in water leakage.
Getting Started
1. Load Dishwasher (See Preparing and
Loading Dishes).
2. Add detergent (See Dishwasher
Dispenser & Detergents).
3. Add Rinse Aid, if needed (See Rinse
Aid).
4. Close door to latch.
5. Select desired CYCLE (See Cycle
Chart). The indicator light above the pad will
glow when selected.
6. Select desired OPTION (See Energy
Options). The indicator light above the pad
will glow when selected.
7. Run hot water faucet nearest
dishwasher until water is hot. Turn water off.
8. To start, press START/CANCEL pad.
4
FEATURES AT A GLANCE
Features may vary according to model
Heating Element
Glass Trap
Detergent Dispenser
Overfi ll Protector
Silverware Basket
Lower Rack
Serial Label
(Located on Right)
Top Rack
Nozzle or Spray Arm
Cup Shelves
(on some
models)
Middle Spray Arm
Lower Spray Arm
Rinse Aid
Vent
Your dishwasher cleans by spraying a mixture of hot water and detergent through the spray arms
against soiled surfaces. First, the dishwasher fi lls with water covering the fi lter area. Water is
then pumped through the spray arms. Soil particles go through and across the fi lter and down the
drain as the water is pumped out. This series of steps are repeated as needed. The number of
water fi lls vary with the cycle being used.
NOTE
The dishwasher is programmed to remember
your last cycle so you do not have to reset
each time. To start the dishwasher using
the same cycle and options selected on the
previous wash, just press the START/CANCEL
pad.
ë
Wash Cycle Selections
Cycle times are approximate and will vary with
options selected. Hot water is necessary to
activate dishwasher detergent and melt fatty
food soils. An automatic sensor will check
the incoming water temperature and, if it is
not hot enough, the cycle will be lengthend
for automatic water heating in the main wash
and fi nal rinse of all cycles. This happens
even when HI-TEMP WASH option has not be
selected. When HI-TEMP WASH is selected,
an even higher temperature will be reached to
handle heavier soil loads.
Recommended Cycle for typical
use:
The Normal cycle along with the heated
dry option together provide the best all
around performance. This cycle selection is
recommended for everyday use and is suitable
for a large range of both dish load size and food
quantities remaining on those dishes.
NOTE
If the dishwasher door is opened while the
unit is running, the START/CANCEL pad must
be pressed and the door shut immediately
to return the unit to the selected cycle and
option, this must happen within 10 minutes
for the unit to continue the cycle.
ë
5
OPERATING INSTRUCTIONS
Option Selections (*available on
select Models)
*Sanitize Option
To sanitize your dishes and glassware, select
SANITIZE option. When selected, the light
above the pad will come on and remain on until
the end of the cycle. The water temperature
in the fi nal rinse will be raised to 155
o
F (68
o
C).
This option is available in Heavy and Normal
Cycles. Only these sanitization cycles have
been designed to meet NSF requirements.
The cycle time will be extended until the proper
water temperature is reached.
Washing
action will continue during the water heating
delay. For best results, the incoming water
temperature should be at least 120
o
F (49
o
C).
The sanitize criteria may not be satisfi ed if there
is an interruption of the cycle, power failure or if
the incoming water temperature is below 120
o
F
(49
o
C).
To turn off the SANITIZE option, press the pad
a second time. The light above the pad will
turn off.
*Hi-Temp Wash Option
When HI-TEMP WASH option is selected, the
dishwasher heats water in the main wash to
approximately 140
o
F (60
o
C).
This increase in water temperature helps the
dishwasher detergent remove food grease and
soil from dishes more effectively and aids in
drying. HI-TEMP WASH option can be used with
all cycles except RINSE ONLY. HI-TEMP WASH
is automatically provided when the HEAVY
WASH cycle is selected.
When HI-TEMP WASH option is selected, the
light above the pad will come on and remain
on until end of cycle. To turn off the HI-TEMP
WASH option, press the pad a second time.
The light above the pad will turn off.
NOTE
Not all cycles and options available on all
models.
ë
*Delay Start
Heat Dry
The HEAT DRY option in combination with
rinse aid will enhance drying performance.
The energy required to use the HEAT DRY
option costs pennies per cycle; however you
will have items in your dish load that will not
be completely dry at the end of the cycle.
Child Lock Controls
To prevent children from accidently changing
the dishwasher cycle or starting the
dishwasher, lock the dishwasher controls
by pressing and releasing the AIR DRY pad
for 3 seconds while the door is latched. An
indicator light on the lock graphic pad will
illuminate when the controls are locked and
no new selections can be made until the lock
is released. To unlock the controls, press the
same pad AIR DRY, until the indicator light
goes out.
*Status Indicator Lights
The WASHING light comes on at the beginning
of the cycle and remains on until the end of
the main wash.
Whether heated or unheated dry is selected
the DRYING light will come on during the
drying portion of the cycle.
When the SANITIZE option is selected, the
SANITIZED light will glow when the SANITIZE
cycle is fi nished. If the dishwasher did not
properly sanitize the dishes, the light will not
come on. This can happen if the cycle is
interrupted. The light will remain on until the
door is opened.
The CLEAN light will come on at the end of
cycle and remain on until the door is opened.
To Cancel a Cycle
You can cancel a cycle anytime during the cycle.
Press and hold the START/CANCEL pad for 3
seconds. The light above the cycle and option
selected will go out, the START/CANCEL light
will remain illuminated, the dishwasher will start
a 90 second drain. At the end of the drain,
select the next desired cycle.
The DELAY START option allows you to
automatically delay starting your dishwasher
for either 2-4-6 hours.
To activate delay start option for 2-4-6 hour
delay, press the pad once for a 2 hour delay,
twice for 4 hours and three times for 6 hours.
A light will come on indicating the delay start
hours and will remain on until cycle starts.
Press the START/CANCEL pad to start the delay
option. If the delay option is interrupted, the
START/CANCEL pad will have to be pressed
again to return to delay option.
To cancel the DELAY START option and begin
the cycle before the delay period is over,
press and hold the START/CANCEL pad for 3
seconds.
6
OPERATING INSTRUCTIONS
Not all cycles available on all models
Cycle and intended use Water per
Cycle
Heavy Wash
Recommended for pots, pans,
casseroles and dinnerware
having light to heavily soiled
loads.
9 gal.
34 L.
2
1
/
4
- 2
1
/
2
Hours
Duration*
(approx.)
Normal Wash
Recommended for lightly to
heavily soiled loads.
Light Wash/Eco Wash
Recommended for lightly
soiled loads only.
Top Rack
Recommended for small loads
in the upper rack only that are
light to heavily soiled.
Available Options
Temperature;
Drying
Sanitize, Hi-Temp;
Heat Dry, Air Dry
Rinse Only
For rinsing dishware that will be
washed later.
Sanitize, Hi-Temp,
Normal;
Heat Dry, Air Dry
3 - 8 gal.
12 - 31 L.
1
1
/
2
- 2
1
/
4
Hours
Hi-Temp, Normal;
Heat Dry, Air Dry
5 gal.
18 L.
1
1
/
2
Hours
Hi-Temp, Normal;
Heat Dry, Air Dry
1
/
4
Hour
N/A
2 gal.
9 L.
Cycle and Option Chart
(approx.)
5 gal.
17 L.
1
1
/
4
Hours
7
PREPARING AND LOADING DISHES
Dish Preparation
Scrape away large pieces of food, bones, pits,
toothpicks, etc. The continuously fi ltered wash
fl uid will remove remaining food particles.
Burned-on foods should be loosened before
loading. Empty liquids from glasses and cups.
Foods such as mustard, mayonnaise, vinegar,
lemon juice and tomato based products may
cause discoloration of stainless steel and
plastics if allowed to sit for a long period of
time. Unless the dishwasher is to be operated
at once, it is best to pre-rinse or use the rinse
only cycle to rinse off these food soils.
• Load racks so that large items do not
prevent the detergent dispenser from
opening.
• Check manufacturer’s recommendations
before washing items in question.
• If the dishwasher drains into a Food
Disposer, be sure the disposer is
completely empty before starting
the dishwasher.
Loading the Top Rack
Features and appearance of racks and
silverware basket as shown may vary
from your model.
The upper rack is designed for fl exibility in
loading a wide variety of items including cups,
glasses, stemware, small plates, bowls, etc.
Load glasses in top rack only. Damage may
occur if placed in bottom rack.
Load plastic items in top rack only. Melting
may occur if placed in bottom rack.
Load items with open end facing down for
better cleaning and draining.
Damage may occur if delicate items touch
each other during dishwasher operation.
Long-handled knives and utensils can be
placed in top rack.
Be sure nothing protrudes through the bottom
of the rack to block rotation of middle spray
arm.
10 place settings standard loading pattern
12 place settings standard loading pattern
Some models have a fold-down cup shelf
or a cup shelf/stemware holder. They can
be used to load two levels of cups, juice
glasses, and other short items. Stagger
items on upper level so that water can
reach all inside surfaces. Fold cupshelf up
to load tall glasses.
8
CAUTION
Load sharp items (knives, skewers, etc.)
pointing down.
Failure to do so may result in injury.
PREPARING AND LOADING DISHES
Features and appearance of racks and
silverware basket as shown may vary
from your model.
The lower rack is best for plates, saucers,
bowls, and cookware. Large items should be
placed along the edge so they do not block
the spray arm rotation. For best results, place
bowls, casseroles, and sauce pans with soiled
surface facing down or toward the center. Tilt
slightly for better drainage.
Make sure tall items do not block spray arm
rotation.
Be sure pan handles do not protrude through
the bottom of the rack and block the spray
arm rotation.
Loading the Bottom Rack
10 place settings standard loading pattern.
12 place settings standard loading pattern.
Features and appearance of racks and
silverware basket as shown may vary
from your model.
Load the silverware basket while it is in the
bottom rack or take the basket out for loading
on a counter or table.
For baskets with lids small items like baby
bottle caps, jar lids, corn cob holders, etc.,
can be placed in a covered section. Close the
cover to hold small items in place.
Use suggested loading patterns, as shown, to
increase washability of the silverware.
Be sure nothing protrudes through bottom of
basket or rack to block the spray arm.
Do not mix silver and stainless to avoid
damaging the silver fi nish.
When covers are up, mix items in each
section of the basket with some pointing
up and some down to avoid nesting. Water
spray cannot reach nested items.
Loading the Silverware Basket
9
PREPARING AND LOADING DISHES
Adding a Dish
To add or remove items after wash cycle
starts:
• Unlatch door and wait a few seconds
until wash action stops before opening.
• Add the item, place the door in an
almost closed position, and wait a few
seconds to allow cold air to slowly
expand inside dishwasher.
• Close door fi rmly to latch and resume
cycle.
CAUTION
The use of industrial grade detergent can
damage the heating coil and other parts of
the dishwasher leading to damage to the
unit and surrounding property. Use only
household grade automatic dishwasher
detergents.
If the cover is closed on the Main Wash Cup
open by pressing the Cover Latch.
How much Detergent to use
The amount of detergent to use depends
on the water hardness. Water hardness is
measured in grains per gallon. Using too little
detergent can result in poor cleaning and hard
water fi lming or spotting. Using too much
detergent in soft water can cause etching
to some glassware which is surface damage
that appears like a fi lm but cannot be wiped
off. Your local water company, water softener
company or county extension agent can tell
you the water hardness in your area.
Detergent Usage Chart
Cycle Soft Water
(0-3 grains)
Medium Hard Water
(4-8 grains)
Hard Water
(9-12 grains)
Very Hard Water
(Over 12 grains)
Heavy Wash
or
Normal Wash
Light Wash
or
Energy Saver
Rinse Only
2 teaspoons
(each cup-
1/4 full)
2 teaspoons
(Main Wash
cup-
1/4 full)
No Detergent No Detergent No Detergent
No Detergent
(water softener
recommended)
5 teaspoons
(each cup- fi ll
to line above
“Regular”)
5 teaspoons
(each cup- fi ll
to line above
“Regular”)
8 teaspoons
(each cup-
completely full)
8 teaspoons
(Main Wash
cup- completely
full)
Each Cup-
Completely
Full (water
softener
recommended)
Main
Wash Cup-
Completely Full
(water softener
recommended)
Cover
Main
Wash
Cup
Cover
Latch
Pre-Wash
Cup
Rinse Aid
Indicator
10
DISHWASHER DISPENSER & DETERGENTS
The detergent dispenser has two detergent
cups. The smaller one is for addition to the
pre-wash and the larger is for release to the
main wash.
• Use only fresh automatic dishwashing
detergent. Other detergents may cause
oversudsing.
• When using automatic dishwashing
detergent tabs, place one tab in main
wash cup and close.
• Add detergent just before starting cycle.
• Store detergent in a cool, dry location.
Moist or caked detergent may not dissolve
properly.
Filing the Detergent Dispenser
As a rule, use 1 teaspoon for each grain above 12. For very hard water, detergent alone
may not be enough and then a water softener is recommended to improve water quality and
dishwashing performance.
NOTE
To achieve the best results from your
dishwasher, visit www.dishwashingexpert.com
for general tips regarding the performance
and operation of your dishwasher.
ë
IMPORTANT
Before starting a cycle, run hot water
to clear cool water from pipe.
11
FACTORS AFFECTING PERFORMANCE
Rinse Aid
Rinse aid greatly improves drying,
reduces water spots, fi lming, and
lubricates wash arm bearing for proper
rotation. With it water “sheets” off dishes
rather than forming water droplets that cling
and leave spots.
A dispenser, located next to the detergent cup,
automatically releases a measured amount of
rinse aid during the last rinse. If spotting and
poor drying are problems, increase the amount
of rinse aid dispensed by rotating the dial to a
higher number. The dial is located under the
dispenser cap. The indicator will be dark when
full and will show clear when it is time to refi ll.
To add liquid rinse aid, turn dispense cap 1/4
turn counterclockwise and lift out. Pour in
rinse aid until liquid touches the indicated fi ll
level. Replace cap.
Do not overfi ll since this can cause
oversudsing. Wipe up any spills with a damp
cloth.
The dispenser holds enough for 35 to 140
washes, depending on the setting selected.
Water Pressure
The hot water line to the dishwasher must
provide water pressure between 20 and 120
psi.
Low Water pressure may occur when laundry
or showers are in operation. If you experience
poor wash performance you may need to
wait until water use is reduced before starting
dishwasher.
Water Temperature
Hot water is needed for best dishwashing and
drying results. Water entering the dishwasher
should be at least 120
o
F (49
o
C) to give
satisfactory results.
To check the temperature of the water entering
the dishwasher:
• Turn on the hot water faucet nearest the
dishwasher for several minutes to clear
cool water from pipes.
• Hold a candy or meat thermometer in the
water stream to check the temperature.
• If temperature is below 120
o
F (49
o
C),
have a qualifi ed person raise the hot
water heater thermostat setting.
The HEAT DRY option in combination
with rinse aid will enhance drying
performance. The energy required to use
the HEAT DRY option costs pennies per
cycle. You may choose not to select the
HEAT DRY option; however you will have
items in your dish load that will not be
completely dry at the end of the cycle.
Dispenser Opening Indicator
Dispenser Cap
Adjustable Setting
12
CARE AND CLEANING
WARNING
Burn Hazard
Allow heating element to cool before
cleaning the interior.
Failure to do so can result in burns.
Outer Door - Clean outer door with warm
soapy water and a dishcloth or sponge. Rinse
with clean water and a dry cloth. Do not use
harsh cleaners.
Inside - The inside of the dishwasher
including the fi lter is self-cleaning with normal
use. If needed, clean around the tub gasket
area with a damp cloth. The fi lter is self-
cleaning. A glass trap located in the center of
the fi lter is designed to collect pieces of broken
glass, straws, bones and pits.
Care of Drain Air Gap
If a drain air gap was installed for your built-in
dishwasher, check to make sure it is clean so
the dishwasher will drain properly. A drain air
gap is usually mounted on counter top and can
be inspected by removing the cover. This is
not part of your dishwasher and is not covered
by warranty.
Overfi ll Protector- keeps dishwasher
from overfi lling and is located in the left front
corner of the tub.
• Clean occasionally with household cleaner
containing vinegar or bleach to dissolve
any buildup.
• Overfi ll Protector should move up and
down freely about one inch. If it does
not move, lift and clean underneath.
To empty the glass trap:
1. Grasp the glass trap’s handle and rotate it
90
0
clockwise while pressing down on the
center of the wash arm.
2. Grab the spray arm in the center and lift
the spray arm and glass trap assembly up
and out form the dishwasher.
3. Tip the assembly over an appropriate
container and tap it to empty the glass
trap.
OR, separate the glass trap - pull
the glass trap handle toward you, then
up, then further toward you to slide it
away from the rest of the assembly;
empty it into an appropriate container;
then slide the glass trap back into the
assembly.
4. Place the assembly back into position,
press down on the arm at the center
and rotate the glass trap handle 90
0
counterclockwise being sure the glass
trap ends in the orientation shown in the
image above. To avoid damage to
your unit make sure the spray arm
and glass trap are fully snapped in
place.
Spray Arm varies
by model
Glass Trap
Glass Trap Removal
(1)
(2)
(3)
13
BEFORE YOU CALL
CAUTION
NOTE
Hard water may cause lime deposit buildup
on the interior of the dishwasher. For
cleaning instructions see “Removing Spots
and fi lm” section.
Property Damage Hazard
Freezing temperatures may cause water
lines to rupture. Be sure all supply lines to
and circulating lines within dishwasher are
protected.
Failure to do so could result in property
damage.
Winterizing
NOTE
See Installation Instructions for more details
on disconnecting and restoring service to
your dishwasher.
ë
ë
Food Soils Left on Dishes
• Choose another cycle for longer washing
time.
• Check rack loading section for proper
loading-avoid nesting items.
• Do not overload the dishwasher (See
Preparing and Loading Dishes).
• Home water pressure may be too low-
should be 20 to 120 pounds per square
inch (psi).
• Check incoming water temperature. It
should be about 120
o
F (49
o
C). (See
Factors Affection Performance.)
• Check water hardness. For extremely
hard water, it may be necessary to install
a water softener. (See Detergent Chart).
• Use Fresh Detergent.
• Make sure items are not blocking the
spray arms, preventing them from
rotating.
• Check to verify that the glass trap is
maintained and installed properly (See
Care and Cleaning).
Before calling for service, review this
list. It may save you both time and
expense. This list includes common
experiences that are not the result of
defective workmanship or material in
your dishwasher.
NOTE
To achieve the best results from your
dishwasher, visit www.dishwashingexpert.com
for general tips regarding the performance
and operation of your dishwasher.
ë
A dishwasher left in an unheated place should
be protected from freezing. Have a qualifi ed
person do the following:
To Disconnect Service:
1. Turn off electrical power to the
dishwasher at the supply source by
removing fuses or tripping circuit breaker.
2. Shut off water supply
3. Place a pan under the inlet valve.
Disconnect water line from inlet valve
and drain into pan.
4. Disconnect drain line from pump and
drain water into pan.
To Restore Service:
1. Direct water line discharge into a pan
and open the valve to fl ush the line.
2. Reconnect the water, drain, and
electrical power supply.
3. Turn on water and electrical power
supply.
4. Fill both detergent cups and run
dishwasher through a HEAVY WASH/
POTS & PANS cycle.
5. Check connections to make sure they
do not leak.
Dishes not Dry
• Select heat dry option.
• Make sure the rinse aid dispenser is
fi lled.
• Increase the discharge setting of rinse
aid. (See Rinse Aid).
• Check the incoming water temperature.
Be sure it is at least 120
o
F (49
o
C).
• Check for proper loading-avoid nesting
items.
14
BEFORE YOU CALL
• Use fresh detergent. Old detergent is
ineffective.
• Make sure rinse aid dispenser is fi lled.
• Check to see that proper amount of
detergent is being used for cycle selected.
(See Detergent Dispenser).
• Home water pressure may be too low-it
should be 20 to 120 pounds per square
inch (psi).
Glassware/Flatware Spotted or Cloudy
• Check water hardness. For extremely
hard water, it may be necessary to install
a water softener. (See Detergent Chart).
• Water temperature may be low. Avoid
extremely low or high temperatures. (See
Factors Affecting Performance.
• Avoid overloading and improper loading.
(See Preparing and Loading Dishes).
• Containers, bowls, pots/pans, and any
dishware with concave surfaces that can
collect water should be placed in the rack
facing or angled down so that water is
able to drain even from the lowest point.
• Plastic items may need to be towel dried.
Dishware Chipped
• Load with care and do not overload. (See
Preparing and Loading Dishes).
• Place delicate items in top rack.
• Place glasses securely against pins and
not over pins.
• Load items so they are secure and don’t
jar loose when moving racks in and out.
Move racks in and out slowly.
• Make sure tall glasses and stemware will
clear top of tub when rack is pushed in.
• Fine antique china and crystal should be
hand-washed.
• Cups with a concave bottom will collect
water. Load them at the far left and right
of the upper rack so they will be held in a
tilted position.
• Aluminum utensils can leave gray/black
marks when they rub against other
items. Load Properly.
• Certain high acid foods can cause
discoloration of stainless steel and
plastics if allowed to sit for a long
period. Use the Rinse Only cycle
or rinse by hand if not operating
dishwasher at once.
• Mixing stainless steel and silver utensils
in silverware basket can cause pitting of
the stainless steel blades. Avoid mixing
stainless steel and silver.
Water in Bottom of Tub
• Water left in the tub bottom after the
cycle is complete is not normal. If
water remains in the bottom of the tub,
the dishwasher may not be draining
properly. (See Dishwasher Does not
Drain Properly).
Cycle Takes a Long Time
• The cycle may have been automatically
lengthened to reach key temperatures
due to some factor such as a cool water
supply or a large load of dishes.
• Delay Start option may have been
selected.
• Choose lower temperature options to
shorten the cycle.
• Cycles that are soil-sensing adjust
automatically to assure a good wash
- heavier soils will elicit a longer cycle
response.
Dishware Stained or Discolored
• Tea and coffee can stain cups. Remove
the stains by hand washing in a solution
of 1/2 cup (120 ml) bleach and one quart
(1L) of warm water. Rinse thoroughly.
• Iron deposits in water can cause a yellow
or brown fi lm. A special fi lter installed
in the water supply line will correct this
problem. (See Removing Spots and Film).
Etching
• Using too much detergent especially in
soft or softened water causes damage
that looks like a fi lm but cannot be
removed.
• Adjust the amount of detergent based
on the water hardness. (Check Detergent
Chart).
• Lower the water temperature by selecting
one of the lower temperature options.
Detergent Left in Cups
• Detergent may be old. Discard and use
fresh detergent.
• Be sure the dish load doesn’t block spray
from entering the detergent cup.
• Check to see if cycle has been completed.
• Make sure items do not prevent the
detergent dispenser from opening.
Dishwasher Won’t Fill
• Assure the water supply is turned on.
• Check that the overfi ll protector moves up
and down freely. (See Overfi ll Protector
section).
15
BEFORE YOU CALL
Dishwasher Leaks
• Check that the door gasket is pressed
into its mounting channel, reaches to
the bottom of the tub and does not
extend beyond the end rib so as to
interfere with door closure.
• Spilled rinse aide can cause foam and
lead to overfl owing. Wipe up any spills
with a damp cloth.
• Check to see that the dishwasher is
level. (See Installation Instructions).
• Avoid oversudsing by using the correct
amount of detergent designed for
automatic dishwashers.
• Check to see that dishwasher is level.
(See Installation Instructions).
Normal Sounds You Will Hear
• Normal sounds include water fi ll, water
spray, draining and motor sounds.
• There is a noticeable change in sound
when the wash action switches between
the lower and middle spray arm. This
is normal since each spray arm has its
own sound.
• It is normal for the dishwasher to pause
(no sound) when the wash action is
switching between the lower and middle
spray arms.
Dishwasher Won’t Run
• Check to see if circuit breaker is tripped
or if a fuse is blown.
• Make sure water supply is turned on.
• Check to see if cycle is set correctly. (See
Operating Instructions).
• Is dishwasher set for Delay Start Option.
• Make sure door is closed and latched.
• Make sure START/CANCEL pad is pressed
after the cycle has been selected.
Dishwasher Does Not Drain Properly
• If unit is hooked up to a food waste
disposer, make sure the disposer is
empty.
• Assure the knockout plug has been
removed from inside the food waste
disposer inlet.
• Assure the drain hose isn’t kinked.
• Make sure cycle is complete, not in a
pause.
• Assure the glass trap is maintained and
installed properly assuring no clogs (See
Care and Cleaning).
Stains on Tub Interior
• Washing large amounts of dishware with
tomato based soil can cause a pink/
orange appearance. This will not affect
performance and will gradually fade over
time. Pre-rinsing or using the Rinse Only
cycle will reduce the chance of staining.
Using no heat dry option will lessen
staining.
Dishwasher has an Odor
• Soiled dishes left in dishwasher too long
can create an odor. Use Rinse Only
cycle.
• There will be a “new” smell when fi rst
installed. This is normal.
• Check to see if unit is draining properly.
(See Dishwasher Does Not Drain
Properly).
Removing Spots and Film
Hard water can cause lime deposit buildup
on the interior of the dishwasher. Dishes
and glasses may also get spots and fi lm
for a number of reasons. (See Glassware/
Flatware Spotted or Cloudy section). To
remove buildup, and fi lm, clean using the
following instructions:
1. Load clean dishes and glasses in
normal manner. Do not load any
metal utensils or silverware.
2. Do not add detergent.
3. Select the NORMAL WASH cycle.
Close the door. Press START/CANCEL
pad.
4. Allow dishwasher to run until it starts
the second water fi ll (approximately 8
minutes).
5. Open the door, pour 2 cups of white
vinegar into the bottom of dishwasher.
6. Close the door and allow cycle to
fi nish.
Opening the door during cycle
• If the dishwasher door is opened while
the unit is running, the START/CANCEL
pad must be pressed and the door shut
immediately to return the unit to the
selected cycle and option, this must
happen within 10 minutes for the unit to
continue the cycle.
16
MAJOR APPLIANCE WARRANTY
Your appliance is covered by a one year limited warranty. For one year from your original date of
purchase, Crosley will pay all costs for repairing or replacing any parts of this appliance that prove to
be defective in materials or workmanship when such appliance is installed, used and maintained in
accordance with the provided instructions.
Exclusions
If You Need Service
This warranty does not cover the following:
1. Products with original serial numbers that have been removed, altered or cannot be readily determined.
2. Product that has been transferred from its original owner to another party or removed outside
the USA or Canada.
3. Rust on the interior or exterior of the unit.
4. Products purchased “as-is” are not covered by this warranty.
5. Food loss due to any refrigerator or freezer failures.
6. Products used in a commercial setting.
7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances
not in ordinary household use or used other than in accordance with the provided instructions.
8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance.
9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards,
shelves, etc., which are not a part of the appliance when it is shipped from the factory.
10. Service calls to repair or replace appliance light bulbs, air fi lters, water fi lters, other
consumables, or knobs, handles, or other cosmetic parts.
11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry
trip charges, or mileage expense for service calls to remote areas, including the state of Alaska.
12. Damages to the fi nish of appliance or home incurred during installation, including but not
limited to fl oors, cabinets, walls, etc.
13. Damages caused by: services performed by unauthorized service companies; use of parts other than
genuine Crosley parts or parts obtained from persons other than authorized service companies; or
external causes such as abuse, misuse, inadequate power supply, accidents, fi res, or acts of God.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT
REPAIR OR REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES,
INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE
LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE
YEAR. ELECTROLUX SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH
AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS
WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME STATES AND PROVINCES DO
NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES,
OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS OR
EXCLUSIONS MAY NOT APPLY TO YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.
This warranty only applies in the USA and Canada. In the USA, your appliance is warranted by
Crosley Corporation. In Canada, your appliance is warranted by Crosley Canada Corp. Crosley
Corporation authorizes no person to change or add to any obligations under this warranty.
Obligations for service and parts under this warranty must be performed by Crosley Corporation
or an authorized service company. Product features or specifi cations as described or illustrated are
subject to change without notice.
Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty
period should service be required. If service is performed, it is in your best interest to obtain
and keep all receipts. Service under this warranty must be obtained by contacting Crosley at the
addresses or phone numbers below.
FOR WARRANTY INFORMATION CONTACT:
USA 1.800.944.9044
Canada 1.866.213-9397
FOR PRODUCT INFORMATION CONTACT:
336.761.1212
Crosley Corporation
111 Cloverleaf Drive, Suite 200
Winston-Salem, NC 27103
CROSLEY
www.Crosley.com
®
17
TABLE OF CONTENTS
www.crosley.com USA and Canada 1-336-761-1212
Mesures de sécurité importantes ...............18
Enregistrement de Produit ........................19
Caractéristiques de Lave-Vaisselle ..............20
Fonctionnement de L’appareil ............... 21-22
Préparation et Chargement
de La Vasisselle ................................... 23-25
Distributeur et Détergents .........................26
Facteurs qui Affecte le Rendment ..............27
Entretien et nettoyage ..............................28
Solutions aux Problémes Usuels ...........29-31
Garantie .................................................32
Tout à propos de
l'utilisation
et l'entretien
de votre Dishwasher
Crosley
®
18
MESURES DE SÉCURITÉ IMPORTANTES
AVERTISSEMENT
Ce pictogramme vise à vous avertir de
situations dangereuses susceptibles de
causer des blessures graves, des br
ûlures,
un incendie ou des chocs électriques.
AVERTISSEMENT
Pour reduire les risques d’incendie, de choc
electrique ou de blessures en utilisant votre
lave-vaisselle, suivez les precautions qui
s’imposent, incluant celles qui suivent.
• N’utilisez votre lave-vaisselle que selon
les instructions incluses dans ce guide
d’entretien et d’utilisation.
• Les instructions contenues dans le présent
guide d’entretien et d’utilisation ne visent
pas à couvrir toutes les situations qui
pourraient se présenter. Faites preuve de
sens pratique et prenez les précautions
qui s’imposent lors de l’installation,
l’utilisation et l’entretien de tout appareil
électroménager.
• NSF lave-vaisselle résidentiels certifi és
ne sont pas destinés aux établissements
alimentaires autorisés.
• LE CIRCUIT ÉLECTRIQUE DE CE LAVE-
VAISSELLE DOIT
ÊTRE MIS À LA TERRE.
Lisez les instructions d’installation pour de
plus amples informations.
• Ce lave-vaisselle est conçu pour fonctionner
avec un courant résidentiel normal (120
volts, 60 hertz). Utilisez un circuit équipé
d’un fusible ou un disjoncteur de 15
ampères. Utilisez un fusible de 20 ampères
si le lave-vaisselle est connecté avec un
broyeur à déchets.
• Ne faites pas fontionner le lave-vaisselle si
tous les panneaux de carrosserie ne sont
pas correctement en place.
• Pour éviter qu’une personne puisse
s’enfermer à l’intérieur de l’appareil et/ou y
suffoquer, retirez la porte ou le mécanisme
de verrouillage de porte de tout lave-
vaisselle inutilisé ou mis aux rebuts.
• Tenez vos bébés et enfants loin du lave-
vaisselle en fonctionnement.
• Ne laissez pas vos enfants faire une
utilisation abusive, s’asseoir, grimper ou
jouer sur la porte ou les paniers du lave-
vaisselle.
• Utilisez seulement les détersifs et agents de
rinçage recommandés pour lave-vaisselle.
• Placez les détersifs et agents de rinçage
hors de la portée des enfants.
• Ne modifi ez pas les commandes.
• Ne lavez pas les articles en plastique
à moins d’indication contraire sur les
étiquettas. S’il n y à aucune indication à cet
effet vérifi ez avec le fabricant. Les articles
non recommandés pour être lavés au lave-
vaisselle risquent de fondre et de créer un
reisque d’incendie.
• Si le lave-vaisselle vidange dans un broyeur
à déchets, assurez-vous que ce dernier
est complètement vide avant de mettre en
marche le lave-vaisselle.
AVERTISSEMENT
Lire toutes les instructions avant d’employer
cet appareil:
• Débranchez l’alimentation électrique au lave-
vaisselle avant d’entreprendre tout travail
d’entretien ou de réparation.
• Pour ranger les articles dans le lave-
vaisselle:
• Ranger les couteaux et articles
pointus pour qu’ils ne risquent pas
d’endommager le joint de la porte ou
la cuve.
• Placer les couteaux et articles pointus,
manches vers le haut pour réduire le
risque de coupures.
• Dans certains conditions, il est possible qu’il
se produise une formation d’hydrogène
dans la canalisation d’eau chaude in utilisée
depuis 2 semaines ou plus. L’HYDROGÈNE
EST UN GAZ EXPLOSIF. Si la canalisation
d’eau chaude n’a pas été utilisée pendant
un tel laps de temps, ouvrez tous les
robinets d’eau chaude et laissez lcouler l’eau
pendant plusieurs minutes avant d’utiliser
le lave-vaisselle. Ceci permettra d’évacuer
tout hydrogène accumulé. L’HYDROGÈNE
EST UN GAZ INFLAMMABLE. Ne fumez ou
n’allumez aucune fl amme dans une telle
situation.
• Les réparations doivent être faites par un
techicien qualifi é.
• Ne touchez pas l’élément chauffant pendant
ou immédiatement après l’utilisation.
• Utilisez des soins déchargement du lave-
vaisselle lorsque l’option SANITIZE a été
sélectionné. Le contenu peut être chaude
au toucher immédiatement après la fi n du
cycle.
• La vapeur d’eau de l’évent peut être chaude
au toucher lorsque l’option SANITIZE a été
sélectionné. Soyez prudent et ne laissez pas
les jeunes enfants jouer autour ou toucher
la zone d’évacuation du lave-vaisselle.
• N’entreposez et n’utilisez pas d’essences
et combustibles ou d’autres produits
infl ammables à proximité de cet appareil ou
de tout autre appareil électro-ménager.
Pour votre sécurité
19
ENREGISTREMENT DE PRODUIT
Merci de choisir Crosley
Ce & d’utilisation Le guide de soin fait parie de
notre engagement à la satisfaction du client et
de qualité u produit durant toute la duree de
via de votre nouvel appareil.
Nous regardons votre achat comme
commencement d’un rapport. Pour assurer
notre capacité de continuer de vous servir,
employer cette page pour enregistrer
l’information sur le produit importe.
_________________________________
Date D’Achat
_________________________________
Numéro De Type
_________________________________
Numéro De Série
Informations très importantes-Lisez
avant de faire fonctionner votre lave-
vaisselle!
Bruits Normaux de Fonctionnement
Ce lave-vaisselle ne génère pas le bruit
des autres lave-vaisselle-IL EST PLUS
SILENCIEUX!.
Votre lave-vaisselle avec son système de
Précision Direct
®
se laver à de nombreuses
améliorations à réduire le niveau sonore.
Encore, il est normal d’entendre certains de
ce qui se passe à l’intérieur. Le laver cycles
comprennent plusieurs instances de l’eau
qui pénètre dans l’unité (projection), laver le
fonctionnement d’une pompe à pulveriser de
l’eau sur la vaisselle (moteur & projection) et
de l’exode discharge le fonctionnement d’une
pompe eau sale et les sols. Les variations
dans la capacité de pompage/pulvérisations
sons sont normaux. Au cours d’un cycle, la
pompe commute on et off de nombreuses
fois, et le fonctionnemnet bascule de nouveau
et entre les armes se laver à fournir les
meilleures performances de nettoyage.
VEUILLEZ PRENDRE NOTE: que si
vous comparez ce lave-vaisselle au modèles
précédents, vous serez surpris de tout ce que
vous n’entendrez pas!
REMARQUE
ë
ATTENTION
Risque de dommage à la propriété
Avant de démarrer le lave-vaisselle,
assurez-vous que l’eau est raccordé et
alimenté. Le non-respect de cette étape
pourrait endommager le joint de la pompe
et entraîner des fuites d’eau.
Préparatifs
1. Charger le lave-vaisselle (Voir Préparation
et chargement de vaisselle).
2. Ajouter le détergent (Voir Lave-vaisselle
Distributeur et détergents).
3. Ajouter le produit de rinçage, si necessaire
(Voir Produits de rinçage).
4. Fermer la porte à fond.
5. Sélectionner le CYCLE désirés (Voir
le tableau du cycle). Le voyant
indicateur au-dessus de la plage sera
incandescent.
6. Sélectionner les OPTIONS désirés (Voir les
options énergétiques). Le voyant indicateur
au-dessus de la plage sera incandescent.
7. Faire couler le robinet d’eau chaude le plus
proche du lave-vaisselle jusqu’à ce que l’eau
soit chaude. Fermer le robinet.
8. Pour démarrer, enfoncer le bouton START/
CANCEL.
20
CARACTÉRISTIQUES DE LAVE - VAISSELLE
Votre lave-vaisselle lave la vaisselle et les ustensiles en faisant gicler un mélange d’eau chaude
et de détergent à travers les bras de lavage contre les surfaces souillées. Par la suite, le lave-
vaisselle se remplit d’eau de manière a recouvrir le fi ltre. L’eau est ensuite pompée à travers
le fi ltre et les bras de lavage. L’eau sale chargée de particules solides est pompée par le tuyau
d’écoulement et remplacée par de l’eau propre. Le nombre de remplissages d’eau dépend du
cycle sélectionné.
Options
(*disponsible sur certains
modeles)
*Hi-Temp Wash Option (Option de
Lavage Haute - Temp
Lorsque l’option HI-TEMP WASH est
sélectionnée, le lave-vaisselle porte la
température de l’eau du lavage principal à
environ 140
o
F (60
o
C).
Les caractéristiques peuvent varier selon le modèle
Elément chauffant
Siphone de verre
Distributeur de
détergent
Protection contre
débordement
Panier à ustensiles
Pnaier inférieur
Plaque signalétique
(située sur le côté
droit de la cuve)
Panier supérieur
Ajutage et jet supérieur
Étagères à tasses
(sur quelques
modèles)
Bras de lavage
central
Bras de lavage
inférieur
Distributeur
du produit de
rinçage
Programme recommande pour un
usage normal
Le programme “Normal” avec sa confi guration
d’origine (température normale et type de
séchage) fournit les meilleures performances.
Ce programme est recommandé pour une
utilisation quotidienne. ll est spécialement
adapte, pour à la fois, un remplissage maximal
et une vaisselle très sale.
NOTE
Le lave-vaisselle est programmé pour se
souvenir du dernier cycle, vous n’avez pas
à réinitialiser à chaque fois. Pour démarrer
le lave-vaisselle en utilisant le même
programme et les options sur le lavage
précédent, appuyez simplement sur le bouton
START / CANCEL.
ë
Choix de Cycle de Lavage
Les temps de cycle sont approximatives et
varient en fonction des options sélectionnées.
L’eau chaude est nécessaire pour activer
détergent lave-vaisselle et faire fondre les sols
d’aliments gras. Un capteur automatique vérifi e
la température de l’eau entrant et, si elle n’est
pas assez chaud, le cycle sera lengthend pour le
chauffage automatique de l’eau dans le lavage
principal et le rinçage fi nal de tous les cycles.
Cela se produit même lorsque l’option HI-TEMP
WASH a pas choisi. Lorsque HI-TEMP WASH
est sélectionnée, une température encore plus
élevée sera atteint à manipuler des charges plus
lourdes du sol.
Décharger
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

Crosley CDB350NB7B Le manuel du propriétaire

Crosley
Marque
Crosley
Modèle
CDB350NB7B
Catégorie
Lave-vaisselle
Taper
Le manuel du propriétaire
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents