Sercomm ADC-W115C Manuel utilisateur

Taper
Manuel utilisateur
i
ADC-W115C
Alarm.com Smart Chime
(WiFi Extender)
FCC ID: P27RP200N
IC: 9111A-W115C
ii
User Guide
Table of Contents
CHAPTER 1 INTRODUCTION .......................................................................................... 3
Package Contents .......................................................................................................... 3
Features ......................................................................................................................... 3
LEDs ............................................................................................................................. 4
CHAPTER 2 INITIAL INSTALLATION ........................................................................... 6
Requirements ................................................................................................................ 6
Procedure ...................................................................................................................... 6
CHAPTER 3 CONFIGURATION ....................................................................................... 6
Configuration ................................................................................................................ 6
APPENDIX A SPECIFICATIONS ...................................................................................... 8
ADC-W115C ................................................................................................................. 8
Regulatory Approvals ................................................................................................... 9
Copyright 2019. All Rights Reserved.
Document Version: 1.0
All trademarks and trade names are the properties of their respective owners.
3
Chapter 1
Introduction
This Chapter provides an overview of the ADC-W115Cs features and capabilities.
Congratulations on the purchase of your new ADC-W115C (WiFi extender). The WiFi extend-
er is a consumer electronic device, which is designed to extend the WiFi signal for all
appliances of your home, major from IP cameras, and video doorbells. It allows you to increase
WiFi speed and range by taking the signal from a home router and retransmit to the furthest
corner of your house. Most of the devices can be paired with the extender by just pressing one
button.
Package Contents
The following items should be included:
l ADC-W115C Unit x 1
If any of the above items are damaged or missing, please contact your dealer immediately.
Features
l MT7620DA processor with 32MB Flash and 64MB RAM
l Extend WiFi Range
l Smart LED Indicators
l Two External Antennas
l WPS Function
l Easy to Install
l Compact Design
1
4
LEDs
Front Panel
The ADC-W115C has 4 LEDs.
POWER (Blue) l On - Power On/Normal Operation
l Off - Power Off
l Flashing - Booting
LAN (Blue) l On - WiFi normal operation
l Off - WiFi disable
l Flashing - WPS active (follow WiFi standard) or WiFi
Traffic
WAN (Blue) l On - Connected to the Internet
l Off - Not connected to the Internet
l Flashing - Connecting to the Internet
DEVICE (Blue) l On - Connected to a IP Camera or a Doorbell device
l Off - Not connected to a device
l Flashing - Paring to a new device
Appendix B - About Wireless LANs
5
Rear/Side Panel
Power Plug Connect the power plug to a wall socket.
Reset This button has two (2) functions:
Reboot. When pressed and released, the ADC-W115C will reboot
(restart).
Clear All Data. This button can also be used to clear ALL data
and restore ALL settings to the factory default values.
To Clear All Date and restore the factory default values:
1. Power On.
2. Keep holding the Reset Button down for 3 seconds.
l Release the Reset Button. The ADC-W115C is now using the
factory default values.
WPS Button
Push the WPS button
more than 3
seconds to trigger WPS
pairing
process with voice (PBC mode).
l During the pairing process, the LAN LED will fast blink until WiFi is
successfully connected.
6
Chapter 2
Initial Installation
This Chapter covers the device installation of the WiFi extender.
Requirements
None of cables required for the installation.
Procedure
1. Choose an Installation Site
Select a suitable place to install the ADC-W115C.
2. Power Up
Place the extender near the existing router. Provide the power to the extender so plug it in-
to a wall socket or a power strip. The LEDs light will be ON and make a welcome sound to
notice the extender is boot up successfully.
3. Check the LEDs
All 4 LEDs shall be ON when the power is supplied to the extender.
The Power LED should be ON
The LAN LED should be ON
The WAN LED should be ON
The Device LED should be ON
Chapter 3
Configuration
This Chapter provides Setup details of the WiFi extender.
Configuration
The WiFi extender can offer customers with extending wireless communication between
devices and the router wherever at home. This extender is designed to provide reachable
network connection with all certified devices especially for IP cameras, security doorbells and
other WiFi devices.
Configuring WiFi extender via WPS Button
In this case, make sure an existing router. Follow the steps given below.
2
3
Appendix B - About Wireless LANs
7
Allocate the extender to a near router or an AP. Power on the extender; plug it into the
wall socket or a power strip. It is recommended to press the WPS button on the extender
within 2 minutes after you have pressed the WPS button on your router or AP.
To confirm the pairing process done successfully, check the LAN LED light is fast blink-
ing. Also see the WPS LED light on your router, it will stark blinking.
It will take for a while (about 2 minutes) then will get connected to the router. The extend-
er WAN LED light up after successful Internet connection between the two devices.
8
Appendix A
Specifications
ADC-W115C
Model ADC-W115C (WiFi Extender with Chime)
Dimensions 130mm (H) x 128mm (W) x 72mm (D)
Operating Temperature
0°C - 40°C (32°F - 104°F)
Buttons 2 (1 Reset, 1 WPS button)
Network Protocol: TCP/IP, 802.11 b/g/n
LEDs 4
Power Input 100~120VAC, 60Hz
A
9
Regulatory Approvals
IC warning statement:
RF exposure related statements
RF exposure warning: The equipment complies with RF exposure limits set
forth for an uncontrolled environment. The antenna(s) used for this transmitter
must not be co-located or operating in conjunction with any other antenna or
transmitter.
Déclarations d'exposition aux RF liéesAvertissement d'exposition RF:
L'équipement est conforme aux limites d'exposition aux RF établies pour un
environnement non contrôlé. L'antenne (s) utilisée pour ce transmetteur ne doit
pas être co-localisés ou fonctionnant en conjonction avec une autre antenne ou
transmetteur.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation of the
device.
Ce dispositif est conforme à la norme de l'industrie Canada exempts de
licence RSS (s). L'opération est soumise aux deux conditions suivantes: (1)
Cet appareil ne peut causer d'interférences nuisibles, et (2) cet appareil doit
accepter toute interférence rue, y compris les interférences qui peuvent
causer un mauvais fonctionnement de l'appareil.
This equipment complies with Canada radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with a minimum distance of 20 centimeters between the radiator and your body.
Cet équipement est conforme aux limites Canada exposition aux radiations
établies pour un incontrôlés environnement. Cet équipement doit être installé
et utilisé avec une distance minimale de 20 centimètres entre le radiateur et
votre corps.
10
FCC warning statement:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are de-
signed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television recep-
tion, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to
which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interfer-
ence that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the authority to operate equipment.
This device and its antenna must not be co-
located or operating in conjunction with any other antenna or transmitter.
For product available in the USA/Canada market, only channel 1~11 can be operated. Selec-
tion of other channels is not possible.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

Sercomm ADC-W115C Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues