Firman T08071 Manuel utilisateur

OPERATOR’S MANUAL

Record product information to reference when ordering parts or

obtaining warranty coverage.

TRI-FUEL PORTABLE GENERATOR

MODEL NUMBER

T 0 8 0 7 1

Rev Level:00

P/N:380745471 Rev:05

Table of Contents

Introduction . . . . . . . . . . . .

Features and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Maintenance - Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Troubleshooting- Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Parts Diagrams - Parts Lists - Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Service - Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

REGISTER YOUR PRODUCT

Register your FIRMAN generator online at www.firmanpowerequipment.com

INTRODUCTION

Thank you for purchasing a FIRMAN generator. You have selected a high-quality, precision engineered

generator set designed and tested to give you years of satisfactory service. This generator is Tri-Fuel

and capable of running on gasoline, liquid petroleum gas (LPG), and natural gas (NG). This generator

is not intended for life safety support.

This manual contains safety information to make you aware of the hazards and risks associated

with generator products and how to avoid them. This generator is designed and intended only

for supplying electrical power for operating compatible electrical lighting, appliances, tools and

motor loads, and is not intended for any other purpose. It is important that you read and

understand these instructions thoroughly before attempting to start or operate this portable

generator. Save these original instructions for future reference.

All information in this publication is based on the latest production information available at the

time of approval for printing. The manufacturer reserves the right to change, alter or otherwise

improve the generator and this documentation at any time without prior notice.

INTRODUCTION

01

02

SIGNAL WORDS

DANGER WARNING CAUTION

Indicates a hazard

which, if not avoided,

will result in death or

serious injury.

Indicates a hazard

which, if not avoided,

could result in death

or serious injury.

Indicates a hazard

which, if not avoided,

could result in minor or

moderate injury.

Toxic Fumes- Engine exhaust contains carbon monoxide, a

poisonous gas that will kill you in minutes. You cannot smell

it or see it.

Fire- Fuel and its vapors are extremely flammable which could

cause burns or fire resulting in death or serious injury.Engine

exhaust could cause fire resulting in death or serious injury.

Hot Surface- Muffler could cause burns resulting in serious injury.

Generator could cause electrical shock resulting in death or serious

injury.

Safety Alert Symbol- Indicates a potential personal injury hazard.

Operator's Manual- Failure to follow warnings, instructions and

operator's manual could result in death or serious injury.

English Customer Service: 1-844-FIRMAN1

NOTICE

Indicates information

considered Important,

but not hazard-related.

INTRODUCTION

English Customer Service: 1-844-FIRMAN1

WARNING! This product can expose you to chemicals including gasoline engine

exhaust, which is known to the State of California to cause cancer, and carbon

monoxide, which is known to the State of California to cause birth defects or other

reproductive harm. For more information go to www.P65Warnings.ca.gov.

This outdoor generator can be used to power outdoor items using extension cords or to restore

home power using a transfer switch. A transfer switch is a separate device installed by a licensed

electrician that allows the portable generator to be cord connected, using either of the 120/240V

receptacles, directly into your home’s electrical system. Install a listed transfer switch as soon as

possible if this generator will be used to restore power to your home.

NOTICE If you have questions about intended use, contact customer service. This portable

generator is designed to be used only with FIRMAN authorized parts.

FIRMAN

The generator has a system ground that connects the generator frame components to the ground

terminals on the AC output receptacles. The system ground is connected to the AC neutral wire.

The neutral is bonded to the generator frame.

System Ground

There may be Federal or State regulations, local codes, or ordinances that apply to the intended

use of the generator. Consult a qualified electrician, electrical inspector, or the local agency

having jurisdiction. This generator is not intended to be used at a construction site or similar

activity as defined by NFPA 70-2020 (NEC) section 590.6.

Compliance Requirements

Connections to your home’s electrical system must use a listed* transfer switch installed by a

licensed electrician. The connection must isolate the generator power from the utility power and

comply with all applicable laws and electrical codes.

To Restore Home Power Using a Listed Transfer Switch

Typical

120/240V

Outlet

Transfer

Switch

Typical Indoor Items

To Restore Power Using Extension Cords

03

INTRODUCTION

English Customer Service: 1-844-FIRMAN1

1. Only use grounded cords marked for outdoor use rated for your loads.

16

14

To provide power using

extension cords

Total

Amperage

Minimum Gauge, Outdoor Rated

Up to 50 FT (15m)

Up to 13A

Up to 15A

Up to 20A

Up to 30A

Up to 50A

2. Follow cord safety instructions.

3. Install carbon monoxide alarm(s).

4. When operating portable generator with extension cords, make sure portable generator is located

in an open, outdoor area, at least 20 ft. (6 m.) from occupied spaces with exhaust pointed away.

5. Extension cords running directly into your home, powering indoor items IS NOT RECOMMENDED.

Extension cords running directly into the home increase your risk of carbon monoxide

poisoning through any openings.

If an extension cord running directly into your home is used to power indoor items, the

operator recognizes that this increases the risk of CO poisoning to people inside the home

and assumes that risk.

•

6. Install a listed *transfer switch as soon as possible if this or any generator will be used to restore

power to your home.

*

product safety test standards.

Certified by a Nationally Recognized Testing Laboratory that the product complies to appropriate

DANGER! Engine exhaust contains carbon monoxide, a poisonous gas that will kill

you in minutes. You cannot smell it, see it, or taste it. Even if you do not smell exhaust

fumes, you could still be exposed to carbon monoxide gas.

04

6

INTRODUCTION

1- Fuel Gauge

2- 8.0 Gallon Capacity Fuel Tank

3- Fuel Cap

4- Choke Lever(behind air filter box)

5- Air Filter

6- 439cc FIRMAN OHV Engine

7- Recoil Starter

8- 10.0" Flat Free Wheel

9- Oil Filler Cap

10- Battery

11-

12-

13-

Outlet Cover

Control Panel

Handle

14- LPG/NG Hose Connector(Inlet)

15- LPG/NG Selector Switch

16- Hose Holder

17- LPG Hose with Regulator

19- Power Cord Holder

English Customer Service: 1-844-FIRMAN1

*We are always working to improve our products. Therefore, the enclosed product may differ

slightly from the image on this page.

2①

②

③

⑤

⑥

④

⑦

⑭⑧

⑨

⑩

⑬

⑮

⑪

⑫

⑬

⑭

⑯

⑰

18- Short Power Cord (L14-30P to 4X5-20R)

⑱

⑲

05

FEATURES AND CONTROLS

English Customer Service: 1-844-FIRMAN1

NOTICE Total power drawn from all receptacles must not exceed the name plate rating.

Control Panel

34

2

1

11

5

6

7

8

9

10

12

5

13

1. Main Fuel Selector Switch Engine Switch – Use to select and turn on gasoline (GAS) or LPG/NG

fuel source. The GAS valve is closed when the switch is in the OFF or LPG/NG positions. Engine

switch is on when the switch is in GAS or LPG/NG positions.

/

2. Indicator Light When the main fuel selector switch is turned to the GAS or LPG/NG position,

the indicator light will turn RED for up to 4 minutes (before going off). Starting the engine

successfully anytime during the 4 minutes will turn the indicator light GREEN. See Indicator

light-Battery Power Saving Mode section for more information.

–

5. Circuit Breakers – The receptacles are protected by AC circuit protectors. If the generator is

overloaded or an external short circuit occurs, a circuit protector may trip. If tripping occurs,

disconnect all electrical loads and determine the cause before attempting to continue using the

generator. Reset any tripped circuit protectors.

If multiple receptacles are used at the same time, the total current must be kept with-in the

portable generator nameplate rating.

6. 120V, 20A Duplex GFCI (Ground Fault Circuit Interrupter)- NEMA 5-20R

A maximum of 20 Amps current may be drawn from this duplex receptacle.

7. 120V, 30A Twist Lock – NEMA L5-30R(Not GFCI protected)

A maximum of 30 Amps current may be drawn from this receptacle.

8.120/240V, 30A Twist Lock – NEMA L14-30R(Not GFCI protected)

9.Ground Terminal – Consult an electrician or authority having jurisdiction for local grounding

requirements.

10. 120/240V, 50A – (NEMA 14-50R) (Not GFCI protected)

11. Outlet Cover - Protects the receptacles from dust and debris.

12. LPG/NG Hose Connector (Inlet: 3/8" Flare Male) – Used to connect LPG/NG hose to generator.

13. LPG/NG Selector Switch – Select either LPG or NG.

3. Engine Start Switch – To start engine, press and hold the switch in the START (ll) position, the

engine will crank and attempt to start. When the engine starts, release the switch to the RUN (l) position.

4. 3-1 Data-Minder (Multi-Meter) – Push the SELECT button to show the Voltage, Hertz and running hours.

06

FEATURES AND CONTROLS

A maximum of 30 Amps current for 240 Volts or two independent 120 Volt loads at 30 Amps current each.

A maximum of 33.33 Amps current for 240 Volts or two independent 120 Volt loads at 33.33 Amps current each.

English Customer Service: 1-844-FIRMAN1

OPERATION

1.Location

DANGER! Engine exhaust contains carbon monoxide, a poisonous gas that could kill

you in minutes. You CANNOT smell it, see it, or taste it. Even if you do not smell exhaust

fumes, you could still be exposed to carbon monoxide gas.

•

Operate portable generator only outdoors, at least 20 ft.(6 m) from occupied spaces with exhaust

pointed away to reduce the risk of carbon monoxide accumulating.

Install battery-operated carbon monoxide alarms or plug-in carbon monoxide alarms with

battery back-up according to the manufacturer's instructions. Smoke alarms cannot detect

carbon monoxide gas.

Do not run this portable generator inside homes, garages, basements, crawlspaces, sheds, or

other partially-enclosed spaces even if using fans or opening doors and windows for ventilation.

Carbon monoxide can quickly build up in these spaces and can linger for hours, even after this

product has shut off.

•If you start to feel sick, dizzy, weak or your home’s carbon monoxide alarm sounds, get to fresh air

right away. Call emergency services. You may have carbon monoxide poisoning.

Carbon Monoxide Alarm(s)

Install carbon monoxide alarms

inside your home. Without

wor ki ng ca rbon mo no xi de

alarms, you will not realize you

are getting sick and dying from

carbon monoxide poisoning.

Prevent Carbon Monoxide (CO) Poisoning

Use outdoors at least 20 ft. (6 m) from any home.

Point exhaust away from all homes and occupied spaces.

Install CO alarms inside your home.

20 ft. (6 m) min.

To better educate yourself about all carbon monoxide risks,

go to www.takeyourgeneratoroutside.com.

07

English Customer Service: 1-844-FIRMAN1

Reduce Risk of Fire

WARNING! Exhaust heat/gases could ignite combustibles, structures or damage fuel

tank causing a fire, resulting in death or serious injury.

Keep portable generator at least 5 ft. (1.5 m) from any structure, trees or vegetation over 12

in. (30 cm) in height.

•

Select an outdoor site that is dry and protected from the weather. Do not move portable

generator indoors to protect it from the weather.

Do not locate the portable generator under a deck or other similar structure that may

confine heat and airflow.

•

5 ft.(1.5 m)

min.

5 ft.(1.5 m)

min.

20 ft.(6 m)min.

08

OPERATION

English Customer Service: 1-844-FIRMAN1

2, Oil and Gasoline / LPG/ NG

Add Engine Oil

We recommend using FIRMAN SAE 10W-30 API SL oil for best performance. Other high-quality

detergent oils (API SL or higher) are acceptable. Do not use special additives. Ambient temperature

determines the proper oil viscosity for the engine. Use the chart to select the proper oil for the

outdoor temperature range expected.

NOTICE Do not attempt to crank or start the engine before it has been properly filled with the

recommended type and amount of oil. Damage due to operation with no oil will void your warranty.

Degrees Celsiusº(Outside)

Full Synthetic 5W-30

Degrees Fahrenheitº(Outside)

5W-30 10W-40

10W-30

1.Place generator on a flat, level surface.

2.Clean area around oil fill and remove yellow oil fill cap/dipstick.

3.Wipe dipstick clean.

(H)

DRAIN PLUG

(L)

H

L

09

OPERATION

English Customer Service: 1-844-FIRMAN1

4. Using oil funnel, slowly pour contents of provided oil bottle into oil fill opening until oil reaches

upper limit "H" mark on the dipstick. Be careful not to overfill. Overfilling could cause engine

starting problems or engine damage.

5.Replace oil fill cap/dipstick and fully tighten.

6.Oil level should be checked prior to each use or at least every 8 hours of operation. Keep oil

level maintained.

The portable generator is equipped with a low oil shutdown. If the oil level drops below the

minimum required level, a sensor will activate an internal switch stopping the engine. If the

engine shuts off and the oil level is within specifications, check to see if generator is sitting at an

angle. Place portable generator on an even surface to correct this. If engine fails to start, the oil

level may not be high enough to deactivate the internal low oil level switch. Make sure the sump is

completely full of oil to the upper limit (H). Do not operate engine until oil level issue is corrected.

Contact FIRMAN customer service.

Low Oil Shutdown

Add Gasoline

WARNING! Fuel and its vapors are extremely flammable which could cause burns or fire

resulting in death or serious injury.

Turn generator engine OFF and let it cool at least 2 minutes before removing fuel cap.

Do Not refuel or move generator when engine is running.

Move generator outdoors prior to adding or draining fuel

Keep fuel away from any ignition sources.

Do not overfill tank, allow space for fuel expansion.

If any fuel spills, wait until it evaporates before starting engine

Check and replace fuel lines, tank, cap, and fittings prior to each use if any damage or leaks

are found.

•

Fuel must meet these requirements:

Clean, fresh, unleaded gasoline with a minimum of 87 octane.

For high altitude use, see Operation at High Altitude.

Gasoline with no more than 10% ethanol is acceptable.

•

•E10 E15

10

OPERATION

English Customer Service: 1-844-FIRMAN1

NOTICE Do not mix oil in gasoline or modify engine to run on alternate fuels not described in this

manual. Use of unapproved fuels could damage engine and will not be covered under warranty.

1. Clean area around fuel fill cap, remove cap.

2. Slowly add unleaded fuel to fuel tank. Be careful not to fill above the RED fuel level indicator.

This allows adequate space for fuel expansion.

Red Line Indicator

3. Install fuel cap and let any spilled fuel evaporate before starting engine.

Operation at High Altitude

At altitudes over 5,000 feet(1524 meters), a minimum 85 octane gasoline is acceptable.

Engine power and generator output will be reduced approximately 3.5% for every 1000 feet (305 m)

of elevation above sea level. High altitude may cause hard starting, increased fuel consumption

and sparkplug fouling. To operate at high altitudes FIRMAN can provide a high altitude carburetor

main jet. The alternative main jet and installation instructions can be obtained by contacting

Customer Support.

NOTICE Operation using an alternative main jet at elevations lower than the recommended

minimum altitude can damage the engine. For operation at lower elevations, the standard main

jet supplied must be used. Operating the engine with the wrong main jet may increase exhaust

emissions, fuel consumption and reduce performance.

Altitude main jet 1

Altitude main jet 2

439cc

380717004

380717005

Altitude

3000-6000Feet

6000-8000Feet

Operation at High Ambient conditions

Your FIRMAN Power Equipment product is designed and rated for continuous operation at ambient

temperatures up to 104°F (40°C). The generator may be operated at temperatures ranging from

5°F(-15°C) to 122°F(50°C) for short periods. If the generator is exposed to temperatures outside

this range during storage, the generator should be brought back within this range before

operation . When operated above 77 ° F(25° C ) th e re ma y be a decr e ase in power.

Maximum wattage and current are subject to and limited by such factors as ambient temperature,

altitude, engine conditions etc.

11

OPERATION

English Customer Service: 1-844-FIRMAN1

Connecting LPG/ NG Fuel

WARNING! Liquid Petroleum gas (LPG) and Natural Gas (NG) are extremely

flammable which could cause burns or fire resulting in death or serious injury.

Do not place the LPG/NG sources in the path of muffler outlet or near any ignition source.

Keep a fire extinguisher near the generator all the time.

Do not use or store LPG/NG portable sources not in use near generator or in a building, garage

or enclosed area.

All LPG/NG supply/ piping lines must be installed by a qualified plumber.

If you smell gas, close off all gas sources and contact a qualified plumber to inspect and

repair the LPG or NG system.

Prior to each days first use spray a soapy water solution on LPG/NG fuel connections to check

for leaks.

Never use a gas container, LPG/ NG connector hose, LPG cylinder or NG source that appears

to be damaged.

Do not connect or disconnect the LPG/ NG source in an enclosed area.

LPG is heavier than air and can accumulate in confined / low spaces if there is a leak.

•

NOTICE LPG and NG systems must be installed and used in strict conformance with NFPA 58

(Liquefied Petroleum Gas Code), NFPA 54 (National Fuel Gas Code), manufacturers

recommendations, and comply with the authority having jurisdiction requirements.

To connect your generator to a large propane tank or Natural Gas Supply, contact your gas

equipment company or authority having jurisdiction to assure that you are following all required

codes and regulations.

LPG

Always keep the LPG cylinder in an upright position.

Use only DOT LPG cylinders in vapor service with type 1, right hand ACME threads. Verify the

re-qualification date on the cylinder has not expired.

All new cylinders must be purged of air and moisture prior to filling. The purging process

should be done by your propane gas supplier.

•

Attach the LPG regulator hose assembly (included) to the LPG hose connector (inlet) on the control

panel of the generator. Tighten the nut with a 19 mm or adjustable wrench. Remove the safety plug

or cap from the LPG cylinder valve. Attach the LPG regulator to the cylinder valve. Do not use a

wrench to tighten LPG cylinder nut. Tighten the nut by hand clockwise to a positive stop. Using a

wrench may damage LPG cylinder components.

12

•

OPERATION

English Customer Service: 1-844-FIRMAN1

NG Shut Off Valve

Attach the NG hose (not included) to NG connector (inlet) on the control panel and the NG Source.

We recommend you use a FIRMAN quick connect hose for Natural Gas (NG) connection (This item

is not included). Make sure the NG source location and hose used allows the portable generator to

be located at least 20 ft (6 m) from any occupied spaces.

3.Starting the Generator on Gasoline

1. Before starting the generator, check for loose or missing parts and for any damage which may

have occurred during shipment. Ensure spark plug, muffler, fuel cap, and air cleaner are all in place.

2. Move portable generator outdoors to safe operating location at least 20 ft. (6 m) from any

occupied spaces.

13

Indicator light - Battery Power Saving Mode

This generator is equipped with an electronic module which consumes battery power. When the

main fuel selector switch is turned to the GAS or LPG/NG position, the indicator light will turn

RED for up to 4 minutes (before going off). Starting the engine successfully anytime during the 4

minutes will turn the indicator light GREEN. If portable generator is not started during this

4-minute period the portable generator will switch to Battery Power Saving Mode to conserve

battery life.

NOTICE Your portable generator is equipped with an internal battery charger that will properly

charge the battery only when the engine is running.

The generator cannot be started in Battery Power Saving Mode. Turn main fuel selector switch to

the off position and back to the GAS or LPG/NG position to reset the RED indicator 4-minute

electronic module.

3.If connected make sure the LPG cylinder knob or the NG source valve are fully closed or

disconnected.

CLOSE

OPERATION

English Customer Service: 1-844-FIRMAN1

14

4.Turn the main fuel selector switch to “GAS” position.

NOTICE When the main fuel selector switch is turned to the GAS position, the indicator light will

turn RED for up to 4 minutes (before going off). Starting the engine successfully anytime during

the 4 minutes will turn the indicator light GREEN. See Indicator light-Battery Power Saving

Mode section for more information.

5. Disconnect all electrical loads from the generator. Never start or stop the generator with

electrical devices plugged in.

6. Move choke lever located on engine to “START” position. You do not need to choke a warm engine.

(For electric start move to step (8))

7. For recoil start only - Pull the starter cord slowly until resistance is felt and then pull rapidly to

start engine.

8. For electric start only - Flip the engine switch to the START (ll) position for a few seconds and

then release.

3 sec.

OPERATION

English Customer Service: 1-844-FIRMAN1

9. Do not over-choke. As soon as engine starts and warms up, slowly move the choke lever to the

RUN position.

10. Allow portable generator to run at no load for a few minutes to stabilize before plugging in

any electrical devices.

NOTICE If engine starts but fails to run, or if portable generator shuts down during operation,

check oil level. See Low Oil Shutdown section for more information.

4. Starting the Generator on LPG

1. Before starting the generator, check for loose or missing parts and for any damage which may

have occurred during shipment. Ensure spark plug, muffler, fuel cap, and air cleaner are all in place.

2. Move portable generator outdoors to safe operating location at least 20 ft. (6 m) from any

occupied spaces.

3. Connect the LPG hose with regulator to both LPG cylinder and portable generator LPG/NG Hose

Connector (inlet).

LPG

4. Fully open the LPG cylinder knob.

15

OPERATION

English Customer Service: 1-844-FIRMAN1

5. Turn the LPG/NG selector switch to LPG position.

6. Turn the main fuel selector switch to LPG/NG position.

NOTICE When the main fuel selector switch is turned to the LPG/NG position, the indicator light

will turn RED for up to 4 minutes (before going off). Starting the engine successfully anytime

during the 4 minutes will turn the indicator light GREEN.

See Indicator light-Battery Power Saving Mode section for more information.

7. Disconnect all electrical loads from the generator. Never start or stop the generator with

electrical devices plugged in.

8. Move choke lever located on engine to “START” position.

(For electric start move to step (12))

9. For recoil start only - PULL-TO-PRIME Pull the starter cord 1-2 times. Pull slowly until resistance

if felt and then pull rapidly.

1-2 Times

16

OPERATION

10.For recoil start only - Move the choke lever to the “RUN” position.

English Customer Service: 1-844-FIRMAN1

11. For recoil start only - PULL-TO-RUN Pull the starter cord slowly until resistance if felt and pull

rapidly to run the portable generator.

If the engine fails to start in 1-2 pulls with choke in the RUN position, move choke lever to START

position and repeat the PULL-TO-PRIME step (9).

12. For electric start only - Flip the engine switch to the START (ll) position for a few seconds and

then release.

13. For electric start only - Move the choke lever to the RUN position.

3 sec.

14. Allow portable generator to run at no load for a few minutes to stabilize before plugging in

any electrical devices.

NOTICE If engine starts but fails to run, or if portable generator shuts down during operation,

check oil level. See Low Oil Shutdown section for more information.

NOTICE Observing frost on LPG cylinder and regulator is common during operation and normally

is not an indication of a problem. In unusual situations this frost may eventually restrict the flow of

LPG gas to the generator resulting in deteriorating performance. In these rare situations it can be

helpful to:

17

OPERATION

English Customer Service: 1-844-FIRMAN1

•Exchanging fuel cylinders to allow the first cylinder to warm up, repeating as necessary.

Placing the LPG cylinder at the end of the generator near the handle, where engine fan

air flows out from the generator. This air is slightly heated by air flowing over the engine.

Do not place the LPG cylinder in the path of the muffler exhaust outlet.

•

The LPG cylinder and components can be temporarily warmed by pouring warm water over

them.

•

Muffler

5. Starting the Generator on NG

1. Before starting the generator, check for loose or missing parts and for any damage which may

have occurred during shipment. Ensure spark plug, muffler, fuel cap, and air cleaner are all in place.

2. Move portable generator outdoors to safe operating location at least 20 ft. (6 m) from any occupied

spaces.

3. Connect the NG hose to both the NG source and portable generator LPG/NG Hose Connector (inlet).

NG Shut Off Valve

4. Fully open the NG source valve.

18

OPERATION

English Customer Service: 1-844-FIRMAN1

5. Turn the LPG/NG selector switch to NG position.

6. Turn the main fuel selector switch to LPG/NG position.

NOTICE When the main fuel selector switch is turned to the LPG/NG position, the indicator light

will turn RED for up to 4 minutes (before going off). Starting the engine successfully anytime

during the 4 minutes will turn the indicator light GREEN. See Indicator light-Battery Power Saving

Mode section for more information.

7. Disconnect all electrical loads from the generator. Never start or stop the generator with

electrical devices plugged in.

8. Move choke lever located on engine to “START” position.

(For electric start move to step (12))

9. For recoil start only - PULL-TO-PRIME Pull the starter cord 1-2 times. Pull slowly until resistance

if felt and then pull rapidly.

1-2 Times

19

OPERATION

La page charge ...

Firman T08071 Manuel utilisateur

Firman T08071 Manuel utilisateur

dans d''autres langues

Documents connexes