Viking 5 series Manuel utilisateur

Marque: Viking

Modèle: 5 series

Taper: Manuel utilisateur

Ce manuel convient également à

VDUO5241DSS

Install / Use & Care

MANUAL

5 SERIES

Outdoor Refrigerated Drawers

VDUO5241

NOTE

!CAUTION

CONTENTS

Contents:

Safety information ...............................................................2

Unpacking your appliance ..................................................3

Warranty registration .....................................................3

Installing your appliance ......................................................4

Cabinet clearances .........................................................4

Leveling the appliance ....................................................4

Electrical connection ......................................................5

Installing the anti-tip device .................................................6

Product Dimensions ...........................................................8

Using your Electronic control ............................................10

Care and cleaning .............................................................11

Long term storage / winterization ................................ 11

Stainless steel maintenance ............................................12

Energy saving tips ............................................................12

Service Information .............................................................14

Troubleshooting ................................................................15

Warranty .......................................................................... 16

!WARNING

State of California Proposition 65 Warning:

This product contains one or more chemicals known

to the State of California to cause cancer.

!WARNING

State of California Proposition 65 Warning:

This product contains one or more chemicals known

to the State of California to cause birth defects or

other reproductive harm..

Important Safety Instructions

Warnings and safety instructions appearing in this

guide are not meant to cover all possible conditions and

situations that may occur. Common sense, caution, and

care must be exercised when installing, maintaining, or

operating this appliance.

Recognize Safety Symbols,

Words, and Labels.

!WARNING

WARNING-You can be killed or seriously injured if

you do not follow these instructions.

CAUTION-Hazards or unsafe practices which could

result in personal injury or property / product damage.

NOTE-Important information to help assure a problem

free installation and operation.

NOTE

!CAUTION

XXXXXXXXXXXX

VIKING RANGE, LLC

GREENWOOD, MS 38930

UNPACKING YOUR APPLIANCE

Warranty Registration

It is important you send in your warranty registration card

immediately after taking delivery of your appliance or you

can register online at www.vikingrange.com

The following information will be

required when registering your

appliance.

Service Number

Serial Number

Date of Purchase

Dealer’s name and address

The service number and serial number can be found on the

serial plate which is located inside the cabinet on the left

side near the top. (See ¿ gure 1).

!WARNING

EXCESSIVE WEIGHT HAZARD

Use two or more people to move product.

Failure to do so can result in personal injury.

Remove Interior Packaging

Your appliance has been packed for shipment with all parts

that could be damaged by movement securely fastened.

Remove internal packing materials and any tape holding

internal components in place. The owners manual is

shipped inside the product in a plastic bag along with the

warranty registration card, and other accessory items.

Important

Keep your carton and packaging until your appliance

has been thoroughly inspected and found to be in good

condition. If there is damage, the packaging will be needed

as proof of damage in transit. Afterwards please dispose of

all items responsibly.

Note to Customer

This merchandise was carefully packed and thoroughly

inspected before leaving our plant. Responsibility for its

safe delivery was assumed by the retailer upon acceptance

of the shipment. Claims for loss or damage sustained in

transit must be made to the retailer.

DO NOT RETURN DAMAGED MERCHANDISE TO THE

MANUFACTURER - FILE THE CLAIM WITH THE

RETAILER.

If the appliance was shipped, handled, or stored in other

than an upright position for any period of time, allow the

appliance to sit upright for a period of at least 24 hours

before plugging in. This will assure oil returns to the

compressor. Plugging the appliance in immediately may

cause damage to internal parts.

Figure 1

Online registration

available at

www.vikingrange.com

!WARNING

WARNING - Help Prevent Tragedies

Child entrapment and suffocation are not problems of

the past. Junked or abandoned refrigerators are still

dangerous - even if they sit out for "just a few hours".

If you are getting rid of your old refrigerator, please

follow the instructions below to help prevent

accidents.

Before you throw away your old refrigerator or

freezer:

• Take off the doors or remove the drawers.

• Leave the shelves in place so children may not

easily climb inside.

!WARNING

WARNING - Dispose of the plastic bags which can

be a suffocation hazard.

!CAUTION

Select Location

The proper location will ensure peak performance of your

appliance. We recommend a location where the unit will

be out of direct sunlight and away from heat sources.

To ensure your product performs to speci¿ cations, the

recommended installation location temperature range is

from 5 to 1°F (1 to °C).

Cabinet Clearance

Ventilation is required from the bottom front of the

appliance. Keep this area open and clear of any

obstructions. Adjacent cabinets and counter top can be

installed around the appliance as long as the front grille

remains unobstructed.

Front Grille

Do not obstruct the front grille. The openings within

the front grille allow air to À ow through the condenser

heat exchanger. Restrictions to this air À ow will result in

increased energy usage and loss of cooling capacity. For

this reason it is important this area not be obstructed and

the grille openings kept clean. Viking Range,LLC does not

recommend the use of a custom made grille as air À ow may

be restricted. (See Figure 2).

Front Leveling

Legs

Figure 2

Rear

Leveling

Legs

Front Grille,

keep this area

open.

I NSTALLING YOUR APPLIANCE

Leveling Legs

Adjustable legs at the front and rear corners of the

appliance should be set so the unit is ¿ rmly positioned on

the À oor and level from side to side and front to back. The

overall height of your appliance may be adjusted between

the minimum, 333»4" (85.7 cm), by turning the leveling leg in

(CW ඟ) and the maximum, 343»4" (88.3 cm) by turning the

leveling leg out (CCW ඞ.

To adjust the leveling legs, place the appliance on a solid

surface and protect the À oor beneath the legs to avoid

scratching the À oor. With the assistance of another person,

lean the appliance back to access the front leveling legs.

Raise or lower the legs to the required dimension by turning

the legs. Repeat this process for the rear by tilting the

appliance forward using caution. On a level surface check

the appliance for levelness and adjust accordingly.

The front grille screws may be loosened and the grille

adjusted to the desired height. When adjustment is

complete tighten the two front grille screws. (See Figure 5).

NOTE

Figure 6

Electrical Shock Hazard

• Do not use an extension cord with this appliance.

They can be hazardous and can degrade product

performance.

• This appliance should not, under any

circumstances, be installed to an un-grounded

electrical supply.

• Do not remove the grounding prong from the power

cord. (See Figure 3).

• Do not use an adapter. (See Figure 4).

• Do not splash or spray water from a hose on the

appliance. Doing so may cause an electrical shock,

which may result in severe injury or death.

!WARNING

Electrical Connection

A grounded 115 volt, 15 amp dedicated circuit is required.

This product is factory equipped with a power supply

cord that has a three-pronged, grounded plug. It must

be plugged into a mating grounding type receptacle

in accordance with the National Electrical Code and

applicable local codes and ordinances (see Figure 6). If the

circuit does not have a grounding type receptacle, it is the

responsibility and obligation of the customer to provide the

proper power supply. The third ground prong should not,

under any circumstances, be cut or removed.

Ground Fault Circuit Interrupters (GFCI) are prone to

nuisance tripping which will cause the appliance to shut

down. GFCI’s are generally not used on circuits with power

equipment that must run unattended for long periods of

time, unless required to meet local building codes and

ordinances.

Front grille screw

Front grille

Figure 5

I NSTALLING YOUR APPLIANCE

Figure 3

Figure 4

Do not remove

ground prong

I NSTALLING THE ANTI TIP DEVICE FOR FREESTANDING INSTALLATIONS

!CAUTION

NOTE

Bottom View of

Refrigerator

Anti-Tip

Bracket Leveling Leg

Front of cabinet

211»2"

(54.6 cm)

Figure 7

Floor Mount Installation

The anti-tip bracket is to be located on the À oor in the left or

right rear corner of the refrigerator as shown in Figure 7.

Step by step instructions for locating the

position of the bracket:

1) Decide where you want to place the refrigerator. Slide it

into place, being careful not to damage the À oor, leaving 1"

(2.5 cm) of clearance from the rear wall to allow room for

the anti-tip bracket.

2) Raise the rear leveling legs approximately 1»4" (6 mm)

to allow engagement with the anti-tip bracket. Level the

unit by adjusting all the leveling legs as required. Turning

the leveling leg counterclockwise will raise the unit and

clockwise will lower the unit.

3) Make sure the refrigerator is in the desired location, then

mark on the À oor the rear and side corner of the cabinet

where the anti-tip bracket will be installed. If the installation

does not allow marking the rear corner of the cabinet, then

make temporary lines on the À oor marking the front corner

of the cabinet, excluding the door. Slide the refrigerator out

of the way. From the temporary line extend the sidewall line

back 211»2" (54.6 cm) as shown in Figure 8.

4) Align the anti-tip bracket to the marks on the À oor so

the side of the bracket lines up with the side of the cabinet

mark, and the "V" notches on the anti-tip bracket line up

with the end of the 211»2" (54.6 cm) line (Rear of cabinet

line).

5) Fasten the anti-tip bracket to the À oor using the supplied

screw. (See Figure 8).

6) Slide the cabinet back into position, making sure the

rear cabinet leveling leg slides under the anti-tip bracket

engaging the slot.

!WARNING

• ALL APPLIANCES CAN TIP

RESULTING IN INJURY.

• INSTALL THE ANTI-TIP

BRACKET PACKED WITH

THE APPLIANCE.

• FOLLOW THE

INSTRUCTIONS BELOW

Any ¿ nished À ooring should be protected with appropriate

material to avoid damage when moving the unit.

If installing on a concrete À oor, concrete fasteners are

required, (not included with the anti-tip kit).

Anti-Tip Device

!WARNING

If your refrigerator is not located under a counter

top (free standing), you must use an anti-tip device

installed as per these instructions. If the refrigerator is

removed from its location for any reason, make sure

that the device is properly engaged with the anti-tip

bracket when you push the refrigerator back into the

original location. If the device is not properly engaged,

there is a risk of the refrigerator tipping over, with the

potential for property damage or personal injury.

I NSTALLING THE ANTI TIP DEVICE FOR FREESTANDING INSTALLATIONS

211»2"

(54.6 cm)

"V" notches

in bracket

"V" notches

in bracket

Side of cabinet line

Figure 8

Front of cabinet line

Rear of cabinet line

Rear Leveling leg

Screw

Figure 8a

NOTE

When the À oor mounted anti-tip bracket is used the

minimum adjusted height of the cabinet is increased by

3»8" (9 mm).

ROUGH-IN OPENING DIMENSIONS CABINET DIMENSIONS

MODEL "A" "B" "C" "D" "E" "F" "G" "H" "J"

VDUO5241 24"

(61 cm)

**34" to 35"

(86.4 to 88.9 cm) *237»8"

(60.7 cm)

333»4" to 343»4"

(85.7 to 88.3 cm)

2323»32"

(60.2 cm)

267»32"

(66.6 cm)

4613»32"

(117.9 cm)

261»4"

(66.7 cm)

"A"

"B"

"C"

"D"

"E"

If necessary to gain clearance inside the rough-

in opening a hole can be cut through the adjacent

cabinet and the power cord routed through this hole to

a power outlet. Another way to increase the available

opening depth is to recess the power outlet into the

rear wall to gain the thickness of the power cord

plug. Not all recessed outlet boxes will work for this

application as they are too narrow, but a recessed

outlet box equivalent to Arlington #DVFR1W is

recommended for this application, (see Figure 10).

* Depth dimension of rough-in opening may vary depending on each individual installation. To recess entire door "F"

dimension plus 1" (2.5 cm) for thickness of power cord plug is required.

** Minimum rough-in opening required is to be larger than the adjusted height of the cabinet.

PRODUCT DIMENSIONS

Figure 10

Figure 9

Figure 9a

"F"

211»2"

(54.6 cm)

PRODUCT DATA

MODEL

ELECTRICAL

REQUIREMENTS #

PRODUCT

WEIGHT

VDUO5241 115V/60Hz/15A 140 lbs

(63.6 kg)

"D"

"E"

"H"

"J"

"G"

PRODUCT DIMENSIONS

Figure 11

!WARNING Floor mount Anti-tip Bracket must be installed for freestanding

applications. Not required for built in applications.

# A grounded 15 amp dedicated circuit is required.

Follow all local building codes when installing electrical

and appliance.

Figure 10

Control Function Guide

Function Command Notes

ON/OFF Press and release. Unit will immediately turn ON or OFF.

Adjust Temperature Press or and release.

When the display is ashing, press or to adjust the set

point temperature. Note: temperature displayed is the actual

temperature inside unit.

Toggle Between oF / oC Hold and for 5 seconds. The display will change units.

Leave Interior Light On Press and release to leave interior light on for

12 hours; press again to deactivate.

After 12 hours, factory default is restored; light will turn on when

door is open.

Adjust Light Color While holding , press and release to scroll

through lighting options.

Option Open Door Closed Door

White White

Blue Blue

White Blue

Light will be set at full intensity when door is open, and 50%

intensity when door is closed.

Enable Sabbath Mode Press and hold for 5 seconds and release.

The oF / oC symbol will ash briey after 5 seconds. Interior

light and display will go dark and remain so until user resets

mode - unit continues to operate.

Disable Sabbath Mode Press and release. Display and interior light return to normal operation.

Door Alert Notication

When the door is left open for more than 30 minutes:

• A tone will sound for several seconds every minute

• will appear in display

• Close door to silence alert and reset

Temperature displayed reects actual temperature inside unit. If the

temperature displayed is dierent than selected, the unit is progressing

towards the selected temperature. Time to reach set point varies based

upon ambient temperature, temperature of product loaded, door openings,

etc. Viking recommends allowing the unit to reach set points before loading.

NOTE

Figure 11

USING YOUR ELECTRONIC CONTROL

1

Outdoor Product Long-Term Storage / Winter-

ization:

1. Time to Winterize, when the daily low ambient

temperature is at or below 38°F (3.3°C).

!CAUTION

Operation of the unit at ambient temperatures below the

recommended Winterization temperature will void your

warranty.

2. Turn unit off, (see page 10)

3. Remove all contents.

4. If necessary, move the unit so you can gain access to

the rear of the product.

5. Unplug the unit from the power outlet.

It is also recommended that the power to the outlet be

turned-off if the circuit is not required for other items

during the Winter season.

When cleaning unit pay particular attention to any

cracks and crevices that may have accumulated dirt

and debris.

Remove the front toe-grille, and use a brush and

vacuum to clean dirt and debris from beneath the unit.

10.

Thoroughly clean the toe-grille and re-install on the

unit.

Remove the rear access cover, and use a brush and

vacuum to clean dirt and debris from the machine

compartment.

11. Thoroughly clean the rear access cover and re-install

on the unit.

12. Wipe down all interior surfaces with anti-bacterial

cleaner to be followed with clean rinse water to remove

any residual chemicals which could cause staining. Do

not use any abrasive cleaners or scouring pads.

13. Leave the door open and allow to completely dry out

before closing the door.

14. Thoroughly clean the door gasket with anti-bacterial

cleaner to be followed with clean rinse water to remove

any residual chemicals.

15. Thoroughly clean the exterior with a cleaner approved

for stainless steel. Do not use any abrasive cleaners or

scouring pads. See "Stainless Steel Maintenance" on

page 14.

16. Any mounting hardware / fasteners that are showing

signs of corrosion should be replaced.

17. Once the exterior has been thoroughly cleaned,

you may want to apply a coating of car wax to help

protect against spotting from moisture, dirt, and debris

that may accumulate on the surfaces during the

Winterization period.

• If the plastic defrost drain pan located under the

compressor contains water, use a sponge to

remove as much water as possible.

Front Grille

Be sure that nothing obstructs the required air À ow

openings in front of the cabinet. At least once or twice a

year, brush or vacuum lint and dirt from the front grille area

(see page 4).

SHOCK HAZARD: Disconnect electrical power from the

appliance before cleaning with soap and water.

Cabinet

The stainless steel cabinet can be washed with either a

mild soap and water and thoroughly rinsed with clear water.

See "Stainless Steel Maintenance" on page 16.

Interior

Wash interior compartment with mild soap and water. Do

NOT use an abrasive cleaner, solvent, polish cleaner or

undiluted detergent.

Care of Appliance

1. Avoid leaning on the door, you may bend the door

hinges or tip the appliance.

2. Exercise caution when sweeping, vacuuming or

mopping near the front of the appliance. Damage to the

grille can occur.

3. Periodically clean the interior of the appliance as

needed.

In the Event of a Power Failure

If a power failure occurs, try to correct it as soon as

possible. Minimize the number of door openings while the

power is off so as not to adversely affect the appliance's

temperature.

Light assembly replacement

All models use LED lamps to illuminate the interior of the

appliance. This component is very reliable, but should one

fail, contact a quali¿ ed service technician for replacement

of the LED.

!CAUTION

• Never attempt to repair or perform maintenance on

the appliance until the main electrical power has been

disconnected. Turning the appliance control "OFF"

does not remove electrical power from the unit's wiring.

• Replace all parts and panels before operating.

!WARNING

Electrocution Hazard

CARE AND CLEANING

CARE AND CLEANING / STAINLESS STEEL MAINTENANCE

Figure 22

Grille

Spacer

Clean out

behind

grille

Figure 23

Soak up

water from

plastic drain

pan if

necessary

Clean out

debris

Remove screws

around perimeter

of access cover.

18. Do not place a cover on the unit, as this can trap

condensation.

After completion of the above, you may choose to store the

unit indoors, although this is not required.

Remove screw from

each end of grille

Access cover

Background

Stainless steel does not stain, corrode, or rust as easily

as ordinary steel, but it is not stain or corrosion proof.

Stainless steels can discolor or corrode if not maintained

properly.

Stainless steels differ from ordinary carbon steels by the

amount of chromium present. It is this chromium that

provides an invisible protective ¿ lm on the surface called

chrome-oxide. This protective chrome-oxide ¿ lm on the

surface can be damaged or contaminated, which may

result in discoloration, staining, or corrosion of the base

metal.

Care & Cleaning

Routine cleaning of the stainless steel surfaces will serve

to greatly extend the life of your product by removing

contaminants. This is especially important in coastal areas

which can expose the stainless to severe contaminants

such as halide salts, (sodium chloride).

It is strongly recommended to periodically inspect and

thoroughly clean crevices, weld points, under gaskets,

rivets, bolt heads, and any locations where small amounts

of liquid could collect, become stagnant, and concentrate

contaminates. Additionally, any mounting hardware that is

showing signs of corrosion should be replaced.

Frequency of cleaning will depend upon the installation

location, environmental, and usage conditions.

Choosing a Cleaning Product

The choice of a proper cleaning product is ultimately that

of the consumer, and there are many products from which

to choose. Depending upon the type of cleaning and the

degree of contamination, some products are better than

others.

Typically the most effective and ef¿ cient means for routine

cleaning of most stainless steel products is to give the

surfaces a brisk rubbing with a soft cloth soaked in warm

water and a gentle detergent, or mild mixture of ammonia.

Rubbing should, to the extent possible, follow the polish

lines of the steel, and always insure thorough rinsing after

cleaning.

Although some products are called "stainless steel

cleaners," some may contain abrasives which could

scratch the surface, (compromising the protective chrome-

oxide ¿ lm), and some many contain chlorine bleach which

will dull, tarnish or discolor the surface if not completely

removed.

Start-Up After Long-Term Storage:

If stored outside, it is recommended that the unit again

be thoroughly inspected per the storage instructions

above to address any dirt or debris from the weather

and/or animals/insects.

Connect the unit to electrical power.

Turn unit on and con¿ rm your desired control settings.

Allow 24-hrs for the unit to stabilize before loading

contents.

ENERGY SAVING TIPS / DOOR ALIGNMENT

After the stainless surfaces have been thoroughly cleaned,

a good quality car wax may be applied to help maintain the

¿ nish.

Stainless steel products should never be installed, or stored

in close proximity to chlorine chemicals.

Whichever cleaning product you chose, it should be used

in strict accordance with the instructions of the cleaner

manufacturer.

The following suggestions will minimize the

cost of operating your refrigeration appliance.

1. Do not install your appliance next to a hot appliance

(cooker, dishwasher, etc.), heating air duct, or other

heat sources.

2. Install product out of direct sunlight.

3. Ensure the front grille vents at front of appliance

beneath door are not obstructed and kept clean to

allow ventilation for the refrigeration system to expel

heat.

4. Plug your appliance into a dedicated power circuit. (Not

shared with other appliances).

5. When initially loading your new product, or whenever

large quantities of warm contents are placed within

refrigerated storage compartment, minimize door

openings for the next 12 hours to allow contents to pull

down to compartment set temperature.

6. Maintaining a relatively full storage compartment

will require less appliance run time than an empty

compartment.

7. Ensure door closing is not obstructed by contents

stored in your appliance.

8. Allow hot items to reach room temperature before

placing in product.

9. Minimize door openings and duration of door openings.

10. Use the warmest temperature control set temperature

that meets your personal preference and provides the

proper storage for your stored contents.

11. When on vacation or away from home for extended pe-

riods, set the appliance to warmest acceptable tem-

perature for the stored contents.

12. Set the control to the “off” position if cleaning the

appliance requires the door to be open for an extended

period of time.

Energy saving tips:

NOTE

Bottom

of door

Figure 21a

Door

adjustment

bracket

Bottom

of door

door

ure 2

ustme

SERVICE INFORMATION

If service is required, call your authorized service agency.

Have the following information readily available:

• Model number

• Serial number

• Date purchased

• Name of dealer from whom purchased

Clearly describe the problem that you are having. If you are

unable to obtain the name of an authorized service agency,

or if you continue to have service problems, contact Viking

Range, LLC at (888) 845-4641 or write to:

VIKING RANGE, LLC

PREFERRED SERVICE

111 Front Street

Greenwood, Mississippi 38930 USA

Record the information indicated below. You will need it

if service is ever required. The serial number and model

numbers for your refrigerator are located on the upper wall,

behind the lighting:

Model No. ___________________________________

Serial No. _____________________________________

Date of Purchase ______________________________

Date Installed _________________________________

Dealer’s Name ________________________________

Address _____________________________________

__________________________________________

If service requires installation of parts, use only authorized

parts to insure protection under the warranty.

Keep this manual for future reference.

• Never attempt to repair or perform maintenance on

the appliance until the main electrical power has been

disconnected. Turning the appliance control "OFF"

does not remove electrical power from the unit's wiring.

• Replace all parts and panels before operating.

!WARNING

Electrocution Hazard

Before You Call for Service

If the appliance appears to be malfunctioning, read

through this manual ¿ rst. If the problem persists, check the

troubleshooting guide below. Locate the problem in the

guide and refer to the cause and its remedy before calling

for service. The problem may be something very simple

that can be solved without a service call. However, it may

be required to contact your dealer or a quali¿ ed service

technician.

TROUBLESHOOTING

Problem Possible Cause Remedy

Appliance not cold enough

(See “Adjusting the temperature" on

page 10)

• Control set too warm

• Content temperature not

stabilized.

• Excessive usage or prolonged

door openings.

•AirÀ ow to front grille blocked.

• Door gasket not sealing properly.

• Adjust temperature colder. Allow

24 hours for temperature to

stabilize.

• Allow temperature to stabilize for

at least 24 hours.

•AirÀ ow must not be obstructed to

front grille. See “clearances” on

page 4.

• Check door alignment and/or

replace door gasket.

Appliance too cold

(See “Adjusting the Temperature” on

page 10)

• Control set too cold

• Door gasket not sealing properly.

• Adjust temperature warmer.

Allow 24 hours for temperature to

stabilize.

• Check door alignment and/or

replace door gasket.

No interior light. • Failed LED light assembly or light

switch.

• Contact a quali¿ ed service

technician.

Light will not go out when door is

closed

• Display light is turned on. (Glass

door models only.

• Door not activating light switch.

• Failed light switch

• Turn off display light, shut door.

• Appliance not level, level

appliance, (See page 4, “leveling

legs”)

• Verify the door is aligned properly,

refer to page 15 for instructions.

• Contact a quali¿ ed service

technician.

Noise or Vibration • Appliance not level

• Fan hitting tube obstruction.

• Level appliance, see “Leveling

Legs” on page 4.

• Contact a quali¿ ed service

technician.

Appliance will not run. • Appliance turned off

• Power cord not plugged in.

• No power at outlet.

• Turn appliance on. See “Starting

your appliance” on page 10.

• Plug in power cord.

• Check house circuit.

!CAUTION

In the unlikely event you lose cooling in your unit, do not

unplug the product from the electric supply, but do call

a quali¿ ed service technician immediately. It is possible

that the loss of cooling capacity is a result of excessive

frost build-up on the evaporator cooling coil. In this case,

removing power to the unit will result in the melting of this

excessive quantity of ice, which could generate melt water

that exceeds the capacity of the defrost drain system and

could result in water damage to your home. The end-user

will be ultimately responsible for any water damage caused

by prematurely turning the unit off without appropriately

managing the excess water run-off.

HOUSEHOLD PRODUCT WARRANTY

UNDERCOUNTER REFRIGERATOR / BEVERAGE CENTER WARRANTY

TWO YEAR FULL WARRANTY

Undercounter refrigerators / Beverage Centers and all of their component parts, except as detailed below*†, are warranted to be free from defective materials or

workmanship in normal residential use for a period of two (2) years from the date of original retail purchase. Viking Range, LLC, warrantor, agrees to repair or

replace, at its option, any part which fails or is found to be defective during the warranty period.

*FULL NINETY (90) DAY COSMETIC WARRANTY: Product is warranted to be free from cosmetic defects in materials or workmanship (such as scratches on

stainless steel, paint/porcelain blemishes, etc.) for a period of ninety (90) days from the date of original retail purchase or closing date for new

construction, whichever period is longer. Any defects must be reported to the selling dealer within ninety (90) days from date of original retail purchase.

Viking Range, LLC uses high quality processes and materials available to produce all color ﬁnishes. However, slight color variation may be noticed because

of the inherent differences in painted parts and porcelain parts as well as differences in kitchen lighting, product locations, and other factors. Therefore,

this warranty does not apply to color variation attributable to such factors.

†FULL NINETY (90) DAY WARRANTY IN “RESIDENTIAL PLUS” APPLICATIONS: Viking products are designed and certified for residential use only. They are

not intended for use in commercial applications. Viking products should only be used in accordance to national and local codes. Viking is not

responsible for property damage or injury resulting from use in a commercial application. To support the manufacturing quality of its appliance’s Viking

will provide a full 90 day warranty for products used in “Residential Plus “applications. This “Residential Plus” warranty applies to applications where use

of the product extends beyond residential use but is in compliance with national and local code. In some jurisdictions these applications are zoned as

residential. Examples of, but not limited to, such applications covered by this warranty are bed and breakfasts, fire stations, private clubs, churches,

condominium/apartment common areas etc. Under this "Residential Plus" warranty, the product, its components and accessories are warranted to be free

from defective material or workmanship for a period of ninety (90) days from the date of original retail purchase. Viking Range, LLC, warranter, agrees to

repair or replace, at its option, any part which fails or is found to be defective during the warranty period. This warranty covers parts and labor. This

warranty excludes use of the product in all commercial locations such as restaurants, food service locations and institutional food service locations.

SIX YEAR FULL WARRANTY ON SEALED REFRIGERATION PARTS AS LISTED

Any sealed refrigeration system component, as listed below, is warranted to be free from defective materials or workmanship in normal household use during the

third through the sixth year from the date of original retail purchase. Viking Range, LLC, warranter, agrees to repair or replace, at its option, any part which fails or is

found to be defective during the warranty period.

Sealed Refrigeration System Components: Compressor, Evaporator, Condenser, Connecting Tubing, Dryer/Strainer

TWELVE YEAR LIMITED WARRANTY ON SEALED REFRIGERATION PARTS AS LISTED

Any sealed refrigeration system component, as listed above, which fails due to defective materials or workmanship in normal household use during the seventh

through the twelfth year from the date of original retail purchase will be repaired or replaced, free of charge for the part itself, with the owner paying all other costs,

including labor.

WARRANTY TERMS

This warranty extends to the original retail purchaser of the product warranted hereunder and to each transferee owner of the product during the term of the

original purchaser's warranty. the warranty is transferable by the original retail purchaser via home sale only. If a transferee owner is unable to provide proof of

purchase from the original purchaser and the product has not been previously registered, the production date of the product, located in the serial number of the

product, will serve as the effective warranty start date.

The activation date of the warranty begins from the date of original retail purchase. In the case of new product purchase via building development sales, activation

begins from the earlier date of either certificate of occupancy or 24 months from date of manufacture. Note date of manufacture is identified by serial tag on

product.

This warranty does not cover units purchased as b-stock, liquidation, salvage, seconds, refurbished, as-is, used products.

This warranty shall apply to products purchased in the United States and Canada. Products must be purchased in the country where service is requested. Warranty

service must be performed by a Viking Range LLC authorized service agency or representative. Warranty shall not apply to damage resulting from abuse, accident,

natural disaster, loss of electrical power to the product for any reason, alteration, improper installation, improper operation, or repair service of the product by

anyone other than a Viking Range LLC authorized service agency or representative. This warranty does not apply to commercial usage. Warrantor is not responsible

for consequential or incidental damage whether arising out of breach of warranty, breach of contract or otherwise. Some jurisdictions do not allow the exclusion or

limitation of incidental or consequential damages, so the above limitations do not apply to you.

Owner shall be responsible for proper installation, providing normal care and maintenance, providing proof of purchase upon request, and making the product

reasonably accessible for service. If the product or one of its component parts contains a defect or malfunction during the warranty period, after a reasonable

number of attempts by the warrantor to remedy the defects or malfunctions, the owner is entitled to either a refund or replacement, at the warrantor’s discretion of

the product or its component part or parts. Warrantor’s liability on any claim of any kind, with respect to the goods or services covered hereunder, shall in no case

exceed the price of the goods or service or part thereof which gives rise to the claim.

WARRANTY SERVICE

Under the terms of this warranty, service must be performed by a Viking Range LLC authorized service agent or representative. Service will be provided during

normal business hours Labor performed at overtime or premium rates shall not be covered by the warranty. To obtain warranty service contact Viking Range LLC

Customer Care at 1-888-845-4641. Please have model number, serial number, and date of original purchase available when calling. IMPORTANT: Retain proof of

original purchase to establish warranty period. The return of the owner registration card is not a condition of warranty coverage. You should, however, return the

owner registration card so Viking Range LLC can contact you should any question of safety arise which could affect you. Any implied warranties of merchantability

and fitness applicable to the above described burner assemblies, infrared rotisserie burners, grill grates, and stainless steel parts are limited in duration to the period

of coverage of the applicable express written limited warranties set forth above. Some jurisdictions do not allow limitations on how long an implied warranty lasts, so

the above limitations may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which may vary from jurisdiction to

jurisdiction.

Specifications subject to change without notice.