Gigabyte AORUS MODEL X 11th Le manuel du propriétaire

Marque: Gigabyte

Modèle: AORUS MODEL X 11th

Taper: Le manuel du propriétaire

To reduce the impacts on global warming, the packaging materials of this product

are recyclable and reusable. GIGABYTE works with you to protect the environment.

For more product details, please visit GIGABYTE's website.

AORUS MODEL X

GAMING DESKTOP PC

(GB-AMXI9N8A-2051)

User's Manual

Rev. 1001

The trademarks mentioned in this manual are legally registered to their respective owners.

Disclaimer

Information in this manual is protected by copyright laws and is the property of GIGABYTE.

Changes to the specications and features in this manual may be made by GIGABYTE without

prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or

published in any form or by any means without GIGABYTE's prior written permission.

Documentation Classications

In order to assist in the use of this product, GIGABYTE provides the following types of

documentations:

For quick set-up of the product, read the Quick Start Guide included with the product.

For detailed product information, carefully read the User's Manual.

For product-related information, check on our website at: https://www.gigabyte.com

- 3 -

Table of Contents

Box Contents ...................................................................................................................4

Optional Items .................................................................................................................4

Chapter 1 Hardware Setup .............................................................................................5

1-1 Safety Information ............................................................................................ 5

1-2 Hardware Information ....................................................................................... 6

System Overview .............................................................................................................6

Front View ........................................................................................................................6

Back View-A .....................................................................................................................7

Back View-B ...................................................................................................................10

1-3 Getting Started ............................................................................................... 11

Connecting Peripheral Devices ......................................................................................11

Connecting the Power Cord ...........................................................................................12

Turning on .....................................................................................................................12

Chapter 2 BIOS Setup ..................................................................................................13

2-1 Entering the BIOS Setup ................................................................................ 13

2-2 Setting the BIOS Display Language ............................................................... 14

2-3 Setting Administrator/User Password ............................................................. 15

2-4 Loading Optimized Defaults ........................................................................... 16

2-5 Saving the BIOS Settings and Exiting ............................................................ 17

Chapter 3 Appendix ......................................................................................................18

3-1 Installing a 2.5" Drive ..................................................................................... 18

3-2 Installing a 3.5" Drive ..................................................................................... 19

3-3 Cleaning the Dust Filter .................................................................................. 20

3-4 Using Q-Flash Plus ........................................................................................ 21

Regulatory Notices .................................................................................................... 22

Contact Us ................................................................................................................ 25

Box Contents

5AORUS MODEL X GAMING DESKTOP PC

5Quick Start Guide

5AC power cord

5Antennas

52.5" drive screws

* The box contents above are for reference only and the actual items shall depend on the product package you obtain.

The box contents are subject to change without notice.

Optional Items

Glass side panel

- 4 -

Chapter 1 Hardware Setup

1-1 Safety Information

•Before connecting to the power outlet, make sure that the voltage rating of the power cable is

compatible with the power specication in the country where you are located.

•The power cord plug must be connected to a properly wired and grounded power outlet.

•Be sure that the power outlet you plug the power cord into is easily accessible and located

as close to the equipment operator as possible. When you need to disconnect power to the

equipment, be sure to unplug the power cord from the electrical outlet.

•Do not touch the plug with wet hands, otherwise easily cause electric shock.

•Protect the power cord from being tread upon or pinched, particularly at the plug.

•To avoid damage of internal component, do not place the product on a vibrating surface.

•Operating temperature: 5~35oC.

•Do not place the product near any heat sources such as electric radiators, heat registers,

stoves or other devices (including ampliers) that produce heat.

•The holes or openings on this product are for ventilation to ensure reliable operation of the

product and to protect it from overheating. Do not cover or block the ventilation holes with

any objects.

•Never push objects of any kind into this product through cabinet slots as they may touch

dangerous voltage points or short-out parts that could result in a re or electric shock.

•Never spill liquid of any kind onto or into the product.

•Do not use this product near water, drinks, or all types of liquids. Do not expose this apparatus

to rain, liquid or moisture. Failure to do so may result in electric shock or damage.

•This product is not water proof or oil-proof.

•Clean the equipment with a soft, dry cloth.

•The manufacturer species that the thumbscrews normally should be tightened with a

screwdriver, use of thumbscrews is not considered to compromise the basic principles of

safety associated with the Safety Standard.

•For the motherboard battery replacement, refer to the motherboard’s User Manual.

- 5 -

1-2 Hardware Information

System Overview

Front View

Power Button

The power button allows users to turn on/off the computer.

USB 3.2 Gen 1 Port

The USB 3.2 Gen 1 port supports the USB 3.2 Gen 1 specication and is compatible to the USB 2.0

specication. Use this port for USB devices.

USB Type-C® Port

The reversible USB port supports the USB 3.2 Gen 2x2 specication and is compatible to the USB 3.2 Gen 2,

USB 3.2 Gen 1, and USB 2.0 specication. Use this port for USB devices.

Mic In

The Mic in jack.

Line Out

The line out jack.

- 6 -

Back View-A

Q-Flash Plus Button (Note)

This button allows you to update the BIOS when the power connector is connected but the system is not

powered on.

Clear CMOS Button

Use this button to clear the CMOS values (e.g. BIOS conguration) and reset the CMOS values to factory

defaults when needed.

•Always turn off your computer and unplug the power cord from the power outlet before using

the clear CMOS button.

•Do not use the clear CMOS button when the system is on, or the system may shutdown and

data loss or damage may occur.

•After system restart, go to BIOS Setup to load factory defaults (select Load Optimized Defaults).

SMA Antenna Connectors (2T2R)

Use this connector to connect an antenna.

Tighten the antenna cables to the antenna connectors and then move the antenna to a place

where the signal is good.

(Note) To enable the Q-Flash Plus function, refer to "Chapter 3" of the manual.

- 7 -

(Note) To enable the Q-Flash Plus function, refer to "Chapter 3" of the manual.

RJ-45 LAN Port (LAN2)

The Gigabit Ethernet LAN port provides Internet connection at up to 2.5 Gbps data rate. The following

describes the states of the LAN port LEDs.

Connection/

Speed LED Activity LED

LAN Port

Connection/Speed LED:

State Description

Green 2.5 Gbps data rate

Orange 1 Gbps data rate

Off 100 Mbps data rate

Activity LED:

State Description

Blinking Data transmission or receiving is occurring

On No data transmission or receiving is occurring

USB 3.2 Gen 2 Type-A Port (Red)

The USB 3.2 Gen 2 port supports the USB 3.2 Gen 2 specication and is compatible to the USB 3.2 Gen 1

and USB 2.0 specication. Use this port for USB devices.

Thunderbolt™ 4 Connector (USB Type-C® Port)

The connector supports standard DisplayPort and Thunderbolt™ video outputs. You can connect a standard

DisplayPort/Thunderbolt™ monitor to this connector with an adapter. The Thunderbolt™ connector can

daisy chain up to ve Thunderbolt™ devices. Because of the limited I/O resources of the PC architecture,

the number of Thunderbolt™ devices that can be used is dependent on the number of the PCI Express

devices being installed. You can adjust the Thunderbolt™ settings under Settings\Thunderbolt Conguration

in BIOS Setup. The maximum supported resolution is 5120 x 2880@60 Hz with 24 bpp via single display

output, but the actual resolutions supported are dependent on the monitor being used. Also, the connector

is reversible and supports the USB 3.2 Gen 2 specication and is compatible to the USB 3.2 Gen 1 and

USB 2.0 specication. You can use this port for USB devices, too.

RJ-45 LAN Port (LAN1)

The Gigabit Ethernet LAN port provides Internet connection at up to 10 Gbps data rate. The following

describes the states of the LAN port LEDs.

Speed LED

Connection/

Activity LED Speed LED:

State Description

Green 10 Gbps data rate

Orange 5 Gbps/ 2.5 Gbps/ 1 Gbps/

100 Mbps data rate

Connection/Activity LED:

State Description

Blinking Data transmission or receiving is occurring

On No data transmission or receiving is occurring

USB 3.2 Gen 2 Type-A Port (Red) (Q-Flash Plus Port)

The USB 3.2 Gen 2 port supports the USB 3.2 Gen 2 specication and is compatible to the USB 3.2 Gen 1

and USB 2.0 specication. Use this port for USB devices. Before using Q-Flash Plus (Note), make sure to insert

the USB ash drive into this port rst.

HDMI Port

The HDMI port supports HDCP 2.3 and Dolby TrueHD and DTS HD Master Audio

formats. It also supports up to 192KHz/16bit 7.1-channel LPCM audio output.

You can use this port to connect your HDMI-supported monitor. The maximum supported resolution is

4096x2160@30 Hz, but the actual resolutions supported are dependent on the monitor being used.

After installing the HDMI device, make sure to set the default sound playback device to HDMI.

(The item name may differ depending on your operating system.)

•When removing the cable connected to a back panel connector, rst remove the cable from your

device and then remove it from the motherboard.

•When removing the cable, pull it straight out from the connector. Do not rock it side to side to

prevent an electrical short inside the cable connector.

- 8 -

If you want to install a Side Speaker, you need to retask the Line in jack to be Side Speaker out

through the audio driver.

Center/Subwoofer Speaker Out

Use this audio jack to connect center/subwoofer speakers.

Rear Speaker Out

Use this audio jack to connect rear speakers.

Optical S/PDIF Out Connector

This connector provides digital audio out to an external audio system that supports digital optical audio.

Before using this feature, ensure that your audio system provides an optical digital audio in connector.

Line In/Side Speaker Out

The line in jack. Use this audio jack for line in devices such as an optical drive, walkman, etc.

Line Out/Front Speaker Out

The line out jack.

Mic In

The Mic in jack.

Audio Jack Congurations:

Jack Headphone/2-channel 4-channel 5.1-channel 7.1-channel

Center/Subwoofer Speaker Out a a

Rear Speaker Out a a a

Line In/Side Speaker Out a

Line Out/Front Speaker Out a a a a

Mic In a

- 9 -

Back View-B

DisplayPort

The connector supports DisplayPort 1.4a version.

HDMI Port

The connector supports HDMI 2.1 version.

- 10 -

1-3 Getting Started

This product is designed and intended to be used in vertical position only.

Connecting Peripheral Devices

Connect your peripheral devices such as keyboard, mouse, monitor, and etc. to the desktop computer.

- 11 -

Connecting the Power Cord

Connect the included power cord to the desktop computer and a power outlet.

Turning on

Press the power button to turn on the desktop computer.

- 12 -

Chapter 2 BIOS Setup

Function Keys

•Because BIOS ashing is potentially risky, if you do not encounter problems using the current version of BIOS,

it is recommended that you not ash the BIOS. To ash the BIOS, do it with caution. Inadequate BIOS ashing

may result in system malfunction.

•It is recommended that you not alter the default settings (unless you need to) to prevent system instability or other

unexpected results. Inadequately altering the settings may result in system's failure to boot. If this occurs, try to

clear the CMOS values and reset the board to default values. (Refer to the "Load Optimized Defaults" section

for how to clear the CMOS values.)

Startup Screen

The following startup Logo screen will appear when the computer boots.

Function Keys:

<DEL>: BIOS SETUP\Q-FLASH

Press the <Delete> key to enter BIOS Setup or to access the Q-Flash utility in BIOS Setup.

<F12>: BOOT MENU

Boot Menu allows you to set the rst boot device without entering BIOS Setup. In Boot Menu, use the up

arrow key <h> or the down arrow key <i> to select the rst boot device, then press <Enter> to accept.

The system will boot from the device immediately.

Note: The setting in Boot Menu is effective for one time only. After system restart, the device boot order

will still be based on BIOS Setup settings.

<END>: Q-FLASH

Press the <End> key to access the Q-Flash utility directly without having to enter BIOS Setup rst.

2-1 Entering the BIOS Setup

To access the BIOS Setup program, press the <Delete> key during the POST when the power is turned on.

When the power is turned off, the battery on the motherboard supplies the necessary power to the CMOS to

keep the conguration values in the CMOS.

- 13 -

2-2 Setting the BIOS Display Language

To set the BIOS display language, go to the System Info. menu. The BIOS Language setting allows you to

select the default language used by the BIOS.

- 14 -

2-3 Setting Administrator/User Password

&Administrator Password

Allows you to congure an administrator password. Press <Enter> on this item, type the password, and

then press <Enter>. You will be requested to conrm the password. Type the password again and press

<Enter>. You must enter the administrator password (or user password) at system startup and when entering

BIOS Setup. Differing from the user password, the administrator password allows you to make changes to

all BIOS settings.

&User Password

Allows you to congure a user password. Press <Enter> on this item, type the password, and then press

<Enter>. You will be requested to conrm the password. Type the password again and press <Enter>.

You must enter the administrator password (or user password) at system startup and when entering BIOS

Setup. However, the user password only allows you to make changes to certain BIOS settings but not all.

To cancel the password, press <Enter> on the password item and when requested for the password, enter

the correct one rst. When prompted for a new password, press <Enter> without entering any password.

Press <Enter> again when prompted to conrm.

NOTE: Before setting the User Password, be sure to set the Administrator Password rst.

Go to the Boot menu to set the administrator password or user password for your desktop computer.

- 15 -

2-4 Loading Optimized Defaults

Go to the Save & Exit menu to load the BIOS default settings.

&Load Optimized Defaults

Press <Enter> on this item and select Yes to load the optimal BIOS default settings. The BIOS defaults

settings help the system to operate in optimum state. Always load the Optimized defaults after updating

the BIOS or after clearing the CMOS values.

- 16 -

2-5 Saving the BIOS Settings and Exiting

&Save & Exit Setup

Press <Enter> on this item and select Yes. This saves the changes to the CMOS and exits the BIOS Setup

program. Select No or press <Esc> to return to the BIOS Setup Main Menu.

&Exit Without Saving

Press <Enter> on this item and select Yes. This exits the BIOS Setup without saving the changes made

in BIOS Setup to the CMOS. Select No or press <Esc> to return to the BIOS Setup Main Menu.

&Boot Override

Allows you to select a device to boot immediately. Press <Enter> on the device you select and select Yesto

conrm. Your system will restart automatically and boot from that device.

- 17 -

Chapter 3 Appendix

Refer to the following steps to install a 2.5" drive:

1. Remove the two screws from the side panel. Then pull out the side panel.

2. Release the thumb screw from the 2.5" drive bracket to take out the bracket.

3. Use the bundled screws to secure your 2.5" drive to the bracket.

4. Replace the bracket with the installed 2.5" drive in the desktop computer.

Then connect the hard drive data and power cables to the 2.5" drive.

5. Replace the side panel and secure it with the screws you previously removed.

3-1 Installing a 2.5" Drive

- 18 -

3-2 Installing a 3.5" Drive

Refer to the following steps to install a 3.5" drive:

1. Remove the two screws from the side panel. Then pull out the side panel.

2. Press the tabs of the 3.5" drive bracket on both sides to pull the bracket out of the desktop computer.

3. Secure your 3.5" drive into the bracket by inserting the four pins on the sides of the bracket into the mounting

holes on the sides of the drive.

4. Replace the bracket with the installed 3.5" drive in the desktop computer. Replace the side panel and secure

it with the screws you previously removed.

- 19 -

We suggest that you clean the dust lter regularly to ensure effective ventilation. Refer to the following steps

to remove the dust lter:

1. Pull the front panel outwards from the bottom.

2. Remove the front panel in the direction of the arrow as indicated.

3. Clean the dust lter.

4. Replace the dust lter and front panel.

3-3 Cleaning the Dust Filter

- 20 -

La page est en cours de chargement...

Gigabyte AORUS MODEL X 11th Le manuel du propriétaire

Marque: Gigabyte

Modèle: AORUS MODEL X 11th

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Gigabyte AORUS MODEL X 11th Owner's manual

Gigabyte AORUS MODEL X 11th Le manuel du propriétaire

Gigabyte AORUS MODEL X 11th Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents