DCS CAD1-36E Guide d'installation

Marque: DCS

Modèle: CAD1-36E

Catégorie: Barbecues

Taper: Guide d'installation

Ce manuel convient également à

CAD1-48E

Professional grill cart

Professionnel panier grill

CAD1 models

Modèles CAD1

US CA

INSTRUCTIONS D'INSTALLATION ET

GUIDE D'UTILISATION

INSTALLATION INSTRUCTIONS AND USER GUIDE

CONTENTS

IMPORTANT!

SAVE THESE INSTRUCTIONS

The models shown in this user guide may not be available in all markets and are

subject to change at any time. For current details about model and specification

availability in your country, please visit our website listed on the back cover

or contact your Fisher & Paykel dealer.

Safety and warnings 3

Model identification & dimensions 4

Installation

Shipping inspection 5

Locating the cart 6

Cart assembly instructions 6-11

Attaching Side Shelf (optional) 112

Attaching Sink Drain Kit (optional) 13-17

Using the cart

Removing Drawers 18

Re-installing Drawers 18-19

Freezer Pack (optional) 18

Care & maintenance 20

Service 21

A MESSAGE TO OUR CUSTOMERS

Thank you for selecting this DCS by Fisher & Paykel Grill Cart. This installation and user guide

contains valuable information on how to properly install, and maintain your new Professional Grill

Cart for years of safe and enjoyable use.

Please fill out and submit your Product Registration by visiting our website at

www.dcsappliances.com and selecting “Support” on the home page and then selecting “Product

Registration”. In addition, keep this guide handy, as it will help answer questions that may arise as

you use your new Grill Cart.

For your convenience, product questions can be answered by a DCS Customer Care Representative

at www.dcsappliances.com, or email: customer.care@fisherpaykel.com.

Note: please write the model, code, and serial numbers on this page for references (can be found

on the inside, left wall of the tank drawer).

MODEL NUMBER CODE SERIAL NUMBER

IMPORTANT!

DO NOT discard any packing material (box, pallet, straps) until the unit has been inspected.

Inspect the product to verify that there is no shipping damage. If any damage is detected, call the

shipper and initiate a damage claim. DCS by Fisher & Paykel is not responsible for shipping damage.

SAFETY AND WARNINGS

To reduce the risk of fire, electrical shock, injury to persons, or damage when using the appliance,

follow the important safety instructions listed below:

IMPORTANT SAFETY INSTRUCTIONS!

y Do not allow children or pets to play in or around the cart.

y To prevent personal injury or damage to the drawers, do not overload them. The maximum rating

of each drawer is 35 pounds.

y Do not store items of interest to children above or on the inside of any cart. Children could be

seriously injured if they should climb onto or into the cart to reach these items.

y To prevent injury from tipping, all Series 9 grills must only be used with either CAD1-36E or

CAD1-48E model carts.

IF YOU SMELL GAS:

y Do not turn on any electrical switch; do not use any phone in your building.

y Immediately call your gas supplier from a neighbor’s phone.

y Follow the gas supplier’s instructions.

y If you cannot reach your gas supplier, call the fire department.

y Installation and service must be performed by a qualified installer, service agency or

the gas supplier.

WARNING!

Tip Hazard

Do not push down on the top of the drawers. The unit could tip forward.

Do not overload drawers. Maximum rating of each drawer is 35 pounds.

Failure to follow this advice may result in injury.

WARNING!

Crush Hazard

Improper hand placement during drawer closure may cause injury to hands or

fingers. Always close or open drawers using their handles.

Be sure to keep hands away from drawer edges when opening or closing drawers.

Failure to follow this advice may result in injury.

WARNING!

Explosion Hazard

Do not store or use gasoline or other flammable vapors and liquids inside or in the

vicinity of this or any other appliance.

An LP cylinder not connected for use shall not be stored inside or in the vicinity of

this unit.

MODEL IDENTIFICATION & DIMENSIONS

PRODUCT DIMENSIONS

CAD1-30 CAD1-36/36E CAD1-48/48E

Inches (mm) Inches (mm) Inches (mm)

Overall width of cart

30 (762) 36 (914) 48 (1219)

Overall height of cart

35½ (902) 35½ (902) 35½ (902)

Height of cart chasis

(excluding wheels)

32 (816) 32 (816) 32 (816)

Overall depth of cart

½ (648) 25 ½ (648) 25½ (648)

Depth of cart chasis

(excluding doors & handles)

23½ (597) 23½ (597) 23½ (597)

Width of side shelf bracket

½ (114) 4½ (114) 4½ (114)

Width of side shelf

24 (610) 24 (610) 24 (610)

A E

c b

CAD1-30 and side shelf

Front view

CAD1-36/36E

Front view

CAD1-48/48E

Front view

CAD1-30, CAD1-36/36E and CAD1-48/48E

Side view

INSTALLATION

Compatibility

IMPORTANT!

All Series 9 grills MUST only be used with either CAD1-36E

or CAD1-48E model carts. They cannot be used with any

other CAD1 carts. Series 7 grills can be used with both

CAD1 and CAD1-E cart models.

Shipping inspection

IMPORTANT!

y Do not discard any packing material (box, straps) until the

unit has been inspected.

1 Inspect the Cart to verify that there is no shipping damage.

2 If any damage is detected, call the retail dealer and initiate a

damage claim. DCS by Fisher & Paykel is not responsible for

shipping damage.

y Operate the drawers to be sure they glide smoothly.

y Examine the drawer fronts to be sure there are no dents or

scratches.

Eye Goggles

Work Gloves

5/32” Allen Wrench

3/16” Allen Wrench

Power Screwdriver or Variable

Speed Drill with Phillips - tip #2

Attachment

30” Cart shown

Machined Phillip

screws 10-24X1/2”

Bolt Hex

1/4-20-12”

Nut Hex

1/4-20

Washer

.313 x .750

Bracket, Tab

3/32” Allen Wrench

Top view (with

drawers open)

INSTALLATION

Cart assembly instructions

IMPORTANT!

y Some parts have sharp edges; care must be taken when handling

the various components to avoid injury. Please read safety

information provided in these instructions before beginning

assembly. Wear gloves when handling.

y Two or more people should work together to assemble the cart and

All-Grill, Double Side Burner/Sink, or Double Side Burner/Griddle.

y Avoid using side shelf to move cart. Push or pull the cart by

grasping corners of head.

Locating the cart

For proper use, this product should be installed/positioned

on a flat ground or patio. Unevenness such as bumps, cracks

and protrusions should be

” or less. Refer to illustration

and the below table for required flat area dimensions.

Table of quantity of parts

Tools required

Content included

Your cart is packaged in one box. The box contains your cart and a universal hardware kit to be used

for grill installation and may contain extra hardware for your convenience.

REQUIRED FLAT AREA

CAD1-36/36E CAD1-48/48E

Inches (mm) Inches (mm)

Width

36 (914)

48 (1219)

Depth

48 (1219) 48 (1219)

CONTENTS MODEL PART NO. QTY.

CAD1-30 71131 1

CAD1-36 71132 1

CAD1-36E 71407 1

CAD1-48 71133 1

CAD1-48E 71408 1

CONTENTS

CAD1-

CAD1-36/36E CAD1-48/48E

13 16 17

22 4

22 2

44 4

22 2

INSTALLATION

Cart assembly instructions

IMPORTANT!

Once the carts are linked, they cannot be moved. Moving the carts once linked could damage the carts.

Linking carts together (optional)

To link two or more CAD1 carts, the following instructions must be done first, using the hardware

provided, before installing the top modules.

1 Hand tighten two bolts, four washers, and two nuts on the front and back sides of the carts as shown.

2 Carefully wrench tighten fasteners once carts are aligned with each other.

Front side

Head of bolt with

washer

Front side

Head of bolt with

washer

Back side

End of bolt with

nut and washer

Back side

End of bolt with

nut and washer

Cart assembly instructions

Outdoor appliance head preparation

Head placement onto cart - two persons required

INSTALLATION

1 First you will need to remove the angle

brackets from the side of the unit and

replace them with cart mount brackets.

Note: unit is shipped prepared for island

installation.

1 Remove drip tray/pan and other removable

components such as grates, top burner

caps and components, and griddle flue

cover, radiant tray and grill burner for easier

handling.

2 Install the bracket tab on both sides using

eight of the 10-24 x 1/2” screws. Install each

bracket with four screws on each side of

the grill head. For a CAD1-48/48E, use the

appropriately labeled bracket for your grill

head and cart side.

2 Placing head on cart, place rear of head over

the rear of the cart first. Then allow the rear

side tabs to first locate in the slots on the top

of the cart sides. The other tabs will locate

in the middle and front slots as the head is

lowered into position on the cart.

IMPORTANT!

For the CAD1-48/48E there are two sets of brackets. If you have the BGB48-BQR, use the brackets

labeled LEFT-48 BQR and RIGHT-48 BQR. If you have the BGB48-BQAR, use the brackets labeled

48-BQAR.

IMPORTANT!

y Be aware of pinch points and sharp edges to avoid injury to arms and hand.

y Two persons required to lift head.

Cart assembly instructions

Front end screw installation

INSTALLATION

3 Position tabs on side bracket to fit into slots

on the cart. When complete, the landing

ledge should sit flush on the top of the cart.

1 Install remaining screws (10-24 x 1/2”) into

the front of head to the cart.

4 Secure the head to rear of cart with Phillips-

head screws provided (10-24 x 1/2”).

2 Slide drip tray/pan back into place.

Pinch point

Transformer installation (for Series 9 grills only)

Routing the transformer cord

INSTALLATION

Your Series 9 grill comes supplied with a power transformer for ignition and internal lighting, which

is concealed in a box with an attached power supply cord. It is recommended that the transformer

is mounted to the rear panel of the CAD1-E cart using the 4 holes provided.

HZ VOLTAGE (V) AMPS (A)

60 Hz 120V 15

IMPORTANT!

Use only a Ground Fault Interrupter (GFI)

protected circuit with this transformer.

The suggested location for installation

is above the hole the transformer cord

routes through, which is on the inside

of the right-hand side of the cart’s back

panel. Remove the transformer from its

bracket, and reuse the 4 nuts and bolts

to attach the transformer to the cart.

Route the cord through the provided hole and connect to the nearest 120VAC 15A GFI (Ground

Fault Interrupter) electrical outlet.

Cart assembly instructions

Attach LP gas line connector hose assembly (as shown in “LP Gas Hook-up” section - The

Professsional Liberty Collection, Use/Care Guide) and then connect to LP tank as shown.

To use the cover hangers provided, first place the cover hanger into the slot on the side or rear of

your cart then hang the cover in either direction as shown below.

Gas hook-up - LP

Cover hanger

IMPORTANT!

Do not move the cart while the covers are hung. This could cause the covers to fall off the hangers

and damage the covers.

IMPORTANT!

y To prevent personal injury or damage to the drawers, do not overload them. The maximum rating of

each drawer is 35 pounds.

y Do not push down on the top of the drawers. The unit could tip foward.

INSTALLATION

Side shelf assembly instructions (optional)

Note: side shelf model CAD1-SK can be installed with the head already on the cart.

Optional attach side shelf accessory on either side

INSTALLATION

1 Screw two shoulder bolts into the bottom

screws on the side of the cart. Tighten with

5/32 Allen wrench.

3 Holding the side shelf, install two shoulder

bolts into the slot and screw into the side

shelf tray. Tighten witha 3/16 Allen wrench.

2 Slide left and right side shelf brackets over

the shoulder bolt and install top screw

attaching the side shelf brackets onto the

cart. Tighten with Phillips screwdriver.

4 Place shelf in the up position and check for

level. If shelf is not level, adjust side shelf

set screw. Set screws can be adjusted using

a 3/32 Allen wrench. Turn the Allen wrench

clockwise to raise the shelf. Turn 1/4 turn

and review to see if the shelf is level. The set

screws in the left and right bracket should be

adjusted equally to ensure the shelf sits level.

Shoulder bolt

screw location

Shoulder bolt

screw location

Optional wood cutting board (model # CAD1-WCB, 70861) can

be purchased as an accessory from www.dcsappliances.com.

Sink drain assembly instructions (optional)

INSTALLATION

Tank Bracket

3/4 Hose

Tank Drain

1/2” Ball Valve

Water Hose

Adapter

Sink Drain Hose Assembly

Faucet Hose and Vent Tube

Brass Fitting,

1/4 ID Tube x 1/8 NPT

Work Gloves

Adjustable Pipe Wrench

Flat Head Screw Driver

Phillips Screw Driver

Gray

Water

Tank

Table of quantity of parts

Tools required

Content included

Your Sink Drain Accessory Kit is packaged in one box. The box contains the following components:

CONTENTS QTY.

CONTENTS QTY

Hose Clamp,

9/16” x 1-1/16”

3-1/2” Snap

Bushing

Snap Lock Clip

1-1/2” Tailpiece

Washer

Fitting, 1/2 NPT x 3/4

ID Tube

Nipple,

1-1/2” NPT

Elbow, 3/4 NPT

x 3/4 ID Tube

Cable Tie

Sink drain assembly instructions (optional)

INSTALLATION

IMPORTANT!

Remove all racks and drawers from the cart and grates. And remove burner caps and drip tray from the

side burner/sink prior to kit installation.

1 Attach tank bracket on the right side of the

cart.

3 Install the snap-lock clip in the back bottom

of the cart into the hole provided. Note the

direction of installation.

5 Install the tank/hose assembly in the cart,

over the tank bracket and feed the sink drain

hose through the hole in the center divider.

2 Install the snap bushing in the center divider.

4 Attach sink drain hose assembly to the tank

(include one tailpiece washer).

6 The drain hose at the bottom of the tank

exits the hole in the back of the cart. Attach

the 1/2” ball valve and fitting to the tank and

tighten the hose clamp.

WasherTank Sink drain hose assembly

Sink drain assembly instructions (optional)

INSTALLATION

7 Set the side burner/sink securely on a table

and attach the faucet to the sink as shown.

a Remove the angle brackets from the side of

the unit and replace them with cart mount

brackets.

8 Feed the three-foot water supply hose/air

vent tube through the hole at the bottom of

the burner box, and attach it to the faucet.

b Install the bracket tab on both sides using

eight of the 10-24 x 1/2” screws. Install each

bracket with four screws on each side of

the grill head. For a CAD1-48/48E, use the

appropriately labeled bracket for your grill

head and cart side.

Rubber

Washer

Lock

Washer

Lock

Nut

IMPORTANT!

Finger tight first, then use a wrench.

IMPORTANT!

Excessive weight hazard. Use two or more people to move and install sink/burner assembly onto

the cart.

9 Outdoor appliance head preparation

Sink drain assembly instructions (optional)

INSTALLATION

IMPORTANT!

Beware of pinch points and sharp edges to avoid injury to arms and hands.

a Remove drip tray/pan and other removable

components such as grates, top burner

caps and components, and griddle flue

cover, radiant tray and grill burner for easier

handling.

c Position tabs on side bracket to fit into slots

on the cart. When complete, the landing

ledge should sit flush on the top of the cart.

e Install remaining three screws (10-24 x 1/2”)

into the front of head to the cart.

b Place rear of head over the rear of the cart

first then allow the rear side tabs to first locate

in the slots on the top of the cart sides. The

other tabs will locate in the middle and front

slots as the head is lowered into position.

d Secure the head to rear of cart with Phillips-

head screws provided (10-24 x 1/2”).

!1 Feed the water supply hose through the

center divider hole, down to the bottom

opening of the cart.

!0 Head placement onto cart

Sink drain assembly instructions (optional)

!2 Place the end of the water supply hose in

the snap-lock clip and lock it in place. Attach

the water hose adapter.

!4 Attach the sink drain hose to the bottom

of the sink (use one tailpiece washer) and

push the sink drain hose up and over the

edge of the side panel. This will prevent the

interference between this hose and the top

rack. It also creates proper drainage from the

sink to the water tank. And/or use the cable

tie provided to hold the hose up.

!5 Slide drip tray/pan back into place and

reinstall parts removed in step 10A.

!3 Feed the air vent tube over the center divider

and attach it to the brass fitting located at the

top of the water tank.

!6 Attach cold water hose (not supplied) to the unit and test the system for leaks.

y Close the ball valve behind the cart.

y Turn on the faucet.

y Check all connections inside and outside the cart.

y If you notice any leaks, turn the water supply off. Tighten connections that are leaking and retest.

INSTALLATION

IMPORTANT!

Make sure you have the supply connection in accordance with local codes.

Tailpiece

Washer

USING THE CART

Removing the drawers

IMPORTANT!

To prevent personal injury or damage to the drawers, do not overload them. The maximum rating of

each drawer is 35 pounds.

1 To remove the drawers, pull them out until their slider latch is visible. Carefully push the latch down

on the left side while pulling up on the latch on the right side and pull the drawer completely out of

the frame.

2 To prevent damage to surfaces, place the drawers on a stable surface on a protective towel or

tablecloth while removed from the cart.

Re-installing the drawers

1 Re-install the drawers by extending their

guides.

2 While holding the drawer parallel to the

cabinet, carefully align & engage the ends of

the glides. Slide the drawer about an inch so

that the glides are supporting the back of the

drawer.

USING THE CART

Re-installing the drawers

Freezer pack (optional, kit #70696A)

1 While holding the drawer up by the handle,

pull the glides from the drawer cavity out

over the drawer glide until they click.

3 Install the two racks provided into the

opening by sliding them onto the rollers on

the sidewalls of the left cavity.

1 Place the freezer pack in freezer, laying it flat.

2 Freeze overnight or a minimum of eight hours.

3 Place frozen freezer pack in the steel tray on the second shelf, in appropriate cavity of the drawer.

The freezer pack is dishwasher safe. Or wash with warm soapy water, rinse and air dry. Store flat in

dry storage or in freezer.

2 As you push the drawers in, you will

encounter moderate resistance. Continue to

push the drawer all the way in to complete

the engagement process. The drawer will now

glide smoothly in and out with light effort.

Drain drawer

Rack & rack cover

La page charge ...

DCS CAD1-36E Guide d'installation

Marque: DCS

Modèle: CAD1-36E

Catégorie: Barbecues

Taper: Guide d'installation

Ce manuel convient également à

CAD1-48E

Télécharger le PDF

rapport

dans d''autres langues

English: DCS CAD1-36E Installation guide

DCS CAD1-36E Guide d'installation

Ce manuel convient également à

DCS CAD1-36E Guide d'installation

dans d''autres langues

Documents connexes

Autres documents