Maytag MFD2560HEB Mode d'emploi

Catégorie
Frigos
Taper
Mode d'emploi

Ce manuel convient également à

M/ AG
French Door
_-16
Form No. A/O3/O4
Temperature Controls .................... 10
Fresh Food Features ................ 1 1-13
Freezer Features ............................. 13
Ice And Water ................................... 14
Part No. 12828104
www.maytag.com
.................... 17-19
Care and Cleaning ................... 20-23
Operating Sounds .......................... 24
Troubleshooting ........................ 25-27
Warranty & Service ........................ 29
Guide d'utUisation et
d'entretien ........................................ 30
Guia de uso y cuidado .................. 59
Litho U.S.A.
ImportnntSnfetyInstructions
What You Need to Know About
Safety Instructions
Warning and Important Safety Instructions appearing in
this guide are not meant to cover all possible
conditions and situations that may occur. Common
sense, caution and care must be exercised when
installing, maintaining or operating appliance.
Always contact your dealer, distributor, service agent or
manufacturer about problems or conditions you do not
understand.
Recognize Safety Symbols, Words,
Labels
This appliance is equipped with a three-prong
grounding plug for your protection against possible
electrical shock hazards. It must be plugged into a
grounding receptacle. Where a standard two-prong
wall receptacle is encountered, it is the personal
responsibility and obligation of the customer to have it
replaced with a properly grounded three-prong wall
receptacle. Do not under any circumstances, cut or
remove the third (ground} prong from the power cord.
Do not use an adapter plug.
Power supply cord with
three-prong grounding plug
Grounding type
wall receptacle
ImportnntSnfetyInstructions
SAVE THESE INSTRUCTIONS
Installation
Your refrigerator was packed carefully for shipment.
Remove and discard shelf packaging and tape. Do not
remove the serial plate.
Location
Do not install refrigerator near oven, radiator or other
heat source. If not possible, shield refrigerator with
cabinet material.
Do not install where temperature falls below 55° F
(13° C) or rises above 110° F (43° C). Malfunction may
occur at this temperature.
Refrigerator is designed for indoor household
application only.
Measuring the Opening
When installing your refrigerator, measure carefully.
Allow '/2"space at top and '/2"space behind the machine
compartment cover (located in the rear) for proper air
circulation.
Subflooring or floor coverings (i.e. carpet, tile, wood
floors, rugs) may make your opening smaller than
anticipated.
Some clearance may be gained by using the leveling
procedure under Leveling.
Important: If refrigerator is to be installed into a recess
where the top of the refrigerator is completely covered,
use distance from floor to top of hinge cap to verify
proper clearance.
Leveling
To enhance the appearance and maintain performance,
the refrigerator should be level.
Note
Complete any required door reversal, panel
installation and/or a water supply connection,
before leveling.
Materials Needed
3/8"hex head driver
Carpenter's level
1. Remove toe grille.
Grasp firmly and pull outward
to unclip.
2. Remove bottom hinge cover(s).
Place the eraser end of a pencil or similar blunt
tool in the cover notch.
Transporting Your Refrigerator
NEVER transport refrigerator on its side. If an upright
position is not possible, lay refrigerator on its back.
Allow refrigerator to sit upright for approximately 30
minutes before plugging it in to assure oil returns to
the compressor. Plugging the refrigerator in
immediately may cause damage to internal parts.
Use an appliance dolly when moving refrigerator.
ALWAYS truck refrigerator from its side or
back-NEVER from its front.
Protect outside finish of refrigerator during transport
by wrapping cabinet in blankets or inserting padding
between the refrigerator and dolly.
Secure refrigerator to dolly firmly with straps or
bungee cords. Thread straps through handles when
possible. Do not overtighten. Overtightening restraints
may dent or damage outside finish.
Notch
Location
Use slight pressure to pry the
cover loose.
Continue to maintain
downward pressure to the
notched side of the cover while
swingmg it off.
3. Using hex head driver, turn the front adjustment
screws (A) on each side to raise or lower the front
of the refrigerator.
C C
Installation
/4. Using the hex head driver, turn each of these
adjustment screws (B) to raise or lower the rear of
the refrigerator.
5. Using the carpenter's level, make sure front of
refrigerator is '/4"(6 ram) or '/2bubble higher than
back of refrigerator and that the refrigerator is level
from side to side.
6. Turn stabilizing legs (C) clockwise until firmly
against floor.
7. Turn adjustment screws (A) counterclockwise to
allow the full weight of the refrigerator to rest on
the stabilizing legs.
8. Replace hinge cover(s).
Position cover into the outer edge of the hinge.
Swing the cover toward the cabinet and snap it
into place.
9. Replace the toe grille.
Note
For proper reinstallation, ensure the "top" marking
on the interior of the toe grille is oriented correctly.
Align the toe grille mounting clips with the lower
cabinet slots.
Push the toe grille firmly until it snaps into place.
Door and Drawer Removal
Some installations require door/drawer removal to
transport the refrigerator to its final location.
.
2.
Unplug power cord from power source.
Remove toe grille and bottom hinge
cover(s) (see page 3).
Remove top hinge cover from
refrigerator door by removing Phillips
screw and retain screw and cover for
later use.
Unscrew %6"hex head screws from
top hinge to remove hinge and retain
all screws for later use.
Lift right side refrigerator door from " "
center hinge pin. Remove door
closure from center hinge pin on
the right side and retain for later
use.
Disconnect wire harness on top
of left side refrigerator door top
hinge.
Release two-pin connector by
pressing junction point with a
flat blade screwdriver or
fingernail.
Green ground wire remains
attached to the hinge.
Unscrew 6/,_..hex head screws from
top hinge to remove hinge and retain
for later use.
Lift left side refrigerator door, along
with top hinge, from center hinge pin.
Remove center hinge pin with a _/,_..
hex head driver and retain hinge pin
for later use.
Remove Phillips screws to remove
right and left hinges and retain all
screws for later use.
Remove both stabilizing brackets
with %" hex head driver and retain
screws for later use.
right
stde
door
closure
Installation
Pullout Freezer Drawer
To Install:
1. Pull both rails out to full
extension.
2. While supporting door front,
hook supports into tabs
located on inside of rail.
3. Lower door front into
final position.
To Remove:
1. Pull drawer open to full extension.
2. Pull upper basket out to full extension and lift out
to remove.
.
4.
Lift lower basket straight up and out to remove.
On each side rail is a
basket cradle with two snap
attachments. To release
each cradle, unlatch the
snaps by pushing them
inward, away from the side
rail system. Lift the cradles
off of the rails.
.
Lift top of drawer front
to unhook supports
from rail system. Lift
door front out to
remove.
4. Place the basket cradles back onto the side rails.
Align snaps with the slots on the side rails and
press each snap towards the rail until it clicks.
5. With rails pulled out to full extension, set the
basket straight down into the basket cradles.
Basket cradle
snap attachments
6. Slide upper basket into freezer. Make sure that rear
of basket hooks behind rail catch.
Installation
Door ReinstaHation
1. Install hinge assemblies:
Install top hinge loosely with %_"hex head
screws.
Install center hinge with Phillips
screws.
2. Place hinge side of refrigerator door
on center hinge pin.
3. While holding refrigerator door
upright, tighten down top hinge
with -%_"hex head ddver.
/4. Reconnect two-pin connector.
5. Replace top hinge cover&
3. Ensure the handle clips are
positioned slightly above the
door tabs.
4. Rotate the handle so that the
handle is flat against the door.
5. Push the handle down against the
upper door tab just enough to
allow it to hang unsupported.
i
Handle
Door
Tab
If not installed, the handle is located in the interior of
the fresh food section or attached to the back of your
refrigerator.
Remove and discard handle packaging and tape.
Front Mount Handle
Materiams Needed
Gloves to protect hands
Phillips screwdriver
Plastic door removal card (or h2" thick plastic card},
retain the card
Attach E×tensions to Handle:
__-J
1. Align handle and //
j'.
extension as shown. _,,_X .J/
2. Place extension in _,_-:--_,_Y-
handle opening. --\_\_._: "
3. Apply slight pressure X
to both sides of the extension piece.
4, Slide extension until [t stops on inside edge of
handle,
To Unstall:
1. The handles are to be oriented
as shown.
2. Align front mount door handle
clip with the door tabs.
Align bottom of handle with lower
door tab. Press upper handle end to
door surface and firmly grasp lower
end of handle. Gently slide handle
upward until bottom of handle
settles on door surface, then
reverse direction, sliding downward
to almost engaging tab with clip.
Grasp the handle firmly and slide
down until it clicks. The audible
click indicates fastening clips are
securely interlocked.
To Remove:
1. Flex the handle away from the door
panel. Simultaneously place door
handle removal card underneath
the base of the lower handle. Insert
the card to the line or until it stops.
2. Grasp the lower part of the handle
firmly and lift to remove.
Installation
Freezer Handle
Materials Needed
Gloves to protect hands.
Phillips screwdriver.
Plastic handle removal card (or '/_2"thick plastic
card). Retain the card.
Notes
There is a slight curve to
the freezer handle.
For proper installation, be
sure handle is oriented as
shown.
To Install:
1. Align door handle clips slightly to the left of the
tabs attached to the freezer door.
2. Rotate the handle so the left base is flat against
the door.
Handle Door
While firmly supporting the left handle base against
the door, align the right base of the handle with the
right tabs that are attached to the door.
Now, while firmly holding the handle at the left and
right bases, gently slide the handle towards the
right until the right base settles in. The handle
should now be flat against the face of the freezer
door at both the left and right bases.
With hands still firmly keeping the handle flat
against the freezer door, you may have to reverse
directions momentarily to assure clip/tab
engagement. Then firmly slide the handle to the
right until it clicks. The audible "click" indicates
that the fastening clips are securely interlocked.
To Remove:
At the right end, flex the handle base away from
the surface of the freezer drawer. Simultaneously
slide the door handle removal card that came with
your refrigerator under the right side base of the
handle. Slide the card to the line indication or until
it stops, which will be approximately 1'f2".
With both hands, firmly grasp the handle towards
the right base.
Slide towards the left, lift and remove from the
surface.
3. Push the left handle
base against the left
door tab and slightly
to the right, just
enough to allow it to
hang unsupported.
Installation
Connecting the Water Supply
Materials Needed
Y4"outer diameter flexible copper tubing
Shut-off valve (requires a X" hole to be drilled into
water supply line before valve attachment)
Adjustable wrench
'/_"hex nut driver
Note
You should only use copper tubing for installation.
Plastic is less durable and can cause damage.
Add 8'
supply
to tubing length needed to reach water
for creation of service loop.
Create service loop with copper
tubing (minimum 2' diamete0.
Avoid kinks in the copper tubing
when bending it into a service
loop. Do not use plastic tubing.
2' diameter
minimum
.
3.
Remove plastic cap from water valve inlet
port.
Place brass nut (A) and sleeve (B)
on copper tube end as illustrated. A
Reminder: Do not use an old
sleeve. The nut and sleeve are
provided in the use and care
packet.
Place end of copper tubing into water
valve inlet port. Shape tubing slightly. Do
not kink - so that tubing feeds straight
into inlet port.
5. Slide brass nut over sleeve and screw nut
into inlet port. Tighten nut with wrench.
[MPORTANT: Do not overdghten. Cross
threading may occur.
Pull on tubing to confirm connection is
secure. Connect tubing to frame with
water tubing clamp (C) and turn on
water supply. Check for leaks and
correct if necessary. Continue to
observe the water supply connection
for two to three hours prior to moving
the refrigerator to its permanent
location.
7. Monitor water connection for 24 hours. Correct
leaks, if necessary.
Installation
Opening and Closing Your
Fresh Food Doors
Your new refrigerator is uniquely designed with two
fresh food doors. Either door can be opened or closed
independently of one another.
There is a vertically-hinged section on the left fresh
food door. When the left door is closed, the hinged
section automatically forms a seal between the two
doors when both doors are closed.
When the left door is opened, the hinged seal
automatically folds inward so that it is out of the way.
TemperatureControls
Touch Temperature Controls
The controls are located at the top front of the
refrigerator compartment.
Control
I
Initial Control Settings
After plugging the refrigerator in, set the controls.
Pressing the @ or _ pads adjusts the controls to
the desired setting.
The temperature control range for both
compartments is 1 through 7 (coldest).
Initially set the refrigerator control on 4.
Initially set the freezer control on 4.
Let the refrigerator run at least 8 to 12 hours before
adding food.
Warm Cabinet Surfaces
At times, the front of the refrigerator cabinet may be
warm to the touch. This is a normal occurrence that
helps prevent moisture from condensing on the
cabinet. This condition will be more noticeable when
you first start the refrigerator, during hot weather and
after excessive or lengthy door openings.
Adjusting the Controls
24 hours after adding food, you may decide that one
or both compartments should be colder or warmer. If
so, adjust the control(s) as indicated in the
Temperature Control Guide table below. See page 17
for instructions on checking compartment
temperature.
Except when starting the refrigerator, do not change
either control more than one number at a time.
Allow 24 hours for temperatures to stabilize.
Changing either control will have some effect on the
temperature of the other compartment.
Temperature Control Guide
Refrigerator too warm
Refrigerator too cold
Freezer too warm
Freezer too cold
Turn refrigerator OFF
Set the refrigerator control
to next higher number by
pressing the _ pad.
Set the refrigerator control
to next lower number by
pressing the G pad.
Set the freezer control to
next higher number by
pressing the D pad.
Set the freezer control to
next lower number by
pressing the_ pad.
Press the refrigerator or
freezer @ pad until a dash
(-) appears in the display.
Energy Saver Switch (select models)
Off - The refrigerator uses more energy when this
switch is off, because a heater located in the hinged
seal section of the door is running. This heater helps
prevent condensation formation on the exterior of the
hinged seal. Turn the energy saver switch OFF when
the environment is warm and more humid or if
moisture is noticed on the door exterior.
On - This setting saves energy by not using the
heater. Turn the energy saver switch ON when the
environment is less humid.
10
FreshFoodFeutures
Shelves
Your refrigerator has Spill-Catcher TM Glass Shelves.
The shelves have a spill retainer edge which allows for
easier clean up and some are equipped with a slide
out feature. To slide out, grasp the front of the shelf
and pull forward. Push in the shelf to return to the
original position.
To Remove a Shelf:
Slightly tilt up the front and lift up
the rear of the shelf, then pull the
shelf straight out.
To Lock the Shelf Into Another
Position:
Tilt up the front edge of the shelf.
Insert the hook into the desired frame openings and
let the shelf settle into place.
Be sure the shelf is securely locked at the rear.
Elevator TM Shelf (select models)
The Elevator TM Shelf is equipped with a spill-retaining
edge and the EasyGlide TM slide-out feature. It can be
adjusted up or down without unloading.
To Slide Out Elevator TM Shelf:
Grasp the front of the shelf and pull forward.
Push the shelf in to return to original position.
To Adjust the Elevator TM Shelf:
Pull out the knob on the crank handle.
Rotate the crank clockwise to raise the shelf, and
counterclockwise to lower the height of the shelf.
To Remove Elevator TM Shelf:
Completely unload the shelf and pull the shelf
forward.
Pull until the shelf stops.
Press up on the tabs located underneath its outside
edges and continue pulling forward until the shelf is
clear of the frame.
To Replace Elevator TM Shelf:
Align the shelf to the frame and push it all the way
back. It is not necessary to press up on the tabs for
reinstallation.
In ordinary use, the Elevator TM Shelf frame assembly
does NOT require removal. Though unlikely, and not
recommended, the correct removal procedure is as
follows:
To Remove Frame Assembly:
Unload the shelf completely.
Slide the shelf forward about 2" and manually move
the two rear latches toward the shelf center.
While supporting the entire shelf and frame from
underneath, lift slightly and rotate the assembly
approximately 30° to allow the rear mechanism to
clear the vertical rear side rails.
The entire assembly can then be moved forward
and clear of the refrigerator compartment.
To Reinstall Frame Assembly:
Reverse the removal procedure. Be sure the shelf
is in a level position. When the sliding shelf is
pushed to the rear, it will reposition the rear latches
to their correct operating position.
(style may vary)
Frame AssembNy
SmideOut Shdf
11
FreshFoodFeotures
The Crisper Top serves as the lower fresh food shelf
To Remove the Crisper Top:
Remove crisper drawers
Place hand under the frame to push up the glass Lift
glass out
Lift frame from refrigerator liner rails
To Install:
Replace frame in refrigerator liner rails
Carefully replace glass into frame
Door Storage
Dairy Center
The Dairy Center provides
convenient door storage for
spreadabie items such as butter
and margarine. This compartment can be moved to
different locations to accommodate storage needs. To
use the dairy center, raise the cover.
To Remove:
Raise the cover, pui[ upward and tilt out.
To [nstall:
Slide the Dairy Center in and down until firmly seated
in the door liner.
Door Buckets
Door Buckets can be moved to meet storage needs
To Remove:
. Slide bucket up and pull straight out
To [nstail:
. Slide bucket in and down until
firmly seated in the door linen
Crisper Drawers
The Crisper Drawers provide a higher humidity
environment for fresh fruit and vegetable storage
Controls
The Crisper Controls regulate the amount of humidity
in the crisper drawer. Slide the control toward the
FRUIT setting for produce with outer skins. Slide the
control toward the VEGETABLES setting for leafy
produce.
I
To Remove:
HUMIDITY CONTROLLED
Pull drawer out to full extension Tilt up front of
drawer and pull straight out
To Install:
Insert drawer into frame rails and push back into
place
Note
For best results, keep the crisper drawers tightly
closed.
Temperature-Controlled Drawer
The Wide-N-Fresh TM drawer is a full-width drawer
with adjustable temperature control This drawer can
be used for large party trays, deli items, beverages or
miscellaneous items and features a divider to organize
the drawer into sections if desired
There is a temperature control which adjusts the
amount of cold air allowed into the drawee The
control is located on the right side of the drawer, under
the lid
Set the control to the higher setting _ to provide a
normal refrigerator temperature. Set the drawer on the
Iowersetting _ when a temperature colder than
the main refrigerator compartment is desired. Use the
coldest setting when storing meats.
Notes
Cold air directed to the drawer can decrease
refrigerator temperature. Refrigerator control may
need to be adjusted.
Do not place leafy vegetables in the drawer
Colder temperatures could damage leafy produce
To Remove Drawer:
Lift lid Pull drawer out to full extension Tilt up front
of drawer and pull straight out
To Install Drawer:
Push metal glide rails to the back of the refrigerator.
Place drawer onto rails and slide drawer back until it
falls into place.
continued
12
FreshFoodFeutures
FreezerFeatures
To Remove Divider:
Pull drawer completely out and raise the front of the
divider to unhook it from the rear wall of the drawer
and lift it out.
To install Divider:
Hook back of divider over rear wall of drawer and
lower into place
Accessories
Egg Tray
(style may vary/select models)
The Egg Tray holds a "dozen-
plus" eggs. It can be removed
to carry to a work area or to
be washed.
Wine Trivet/Can Rack (select models)
The Wine Trivet/Can Rack accessory fits in the
Wide-N-Fresh TM drawer or on a shelf.
Bottles or cans can be laid
crosswise, or a single bottle may
be laid in the center depression.
Upper Wire Basket
To Remove:
Pull upper basket out to full extension and lift out to
remove.
To install:
Slide upper basket
into freezer. Make
sure that rear of
basket hooks behind
rail catch.
Note
Lower Freezer Drawer: See page 5 for lower
basket and complete pullout drawer instructions.
Accessories
Ice Bin
The Ice Bin provides
storage for ice.
13
I©eundWuter
Automatic Ice Maker
Connect the ice maker to the water supply as
instructed on page 8. Proper water flow and a level
refrigerator are essential for optimal ice maker
performance.
Operating Instructions
Confirm ice bin is in place and ice maker arm is
down.
After freezer section reaches between to 2° F (-18 °
to -17 ° C), ice maker fills with water and begins
operating. You will have a complete
harvest of ice approximately every
three hours.
Allow approximately 24 hours after
installation to receive first harvest of
ice.
Discard ice created within first 12 hours of operation
to assure system is flushed of impurities.
Stop ice production by raising ice maker arm until
click is heard.
Ice maker will remain in the off position until arm is
pushed down.
The first one or two batches will probably contain
undersized and irregular cubes because of air in the
supply line.
When the ice cubes are ejected it is normal for
several cubes to be joined together at the ends. They
can easily be broken apart. The ice maker will
continue to make ice until the supply of ice cubes
raises the ice maker arm, shutting the ice maker off.
Certain sounds may accompany the various cycles of
the ice maker. The motor may have a slight hum, the
cubes will rattle as they fall into an empty storage
pan and the water valve may click or "buzz"
occasionally.
If the ice is not used frequently, the ice cubes will
become cloudy, shrink, stick together and taste stale.
Empty the ice storage bin periodically and wash it in
lukewarm water. Be sure to dry the bin thoroughly
before replacing it.
Beverages and foods should not be placed in the ice
storage bin for quick chilling. These items can block
the ice maker arm, causing the ice maker to
malfunction.
Turn off (arm up) the ice maker when the water
supply is to be shut off for several hours.
To Remove the Ice Bin:
Pull it forward, away from the ice maker. To avoid the
ice maker dumping ice while the bin is removed, turn
the ice maker off by raising the ice maker arm.
To Install the Ice Bin:
Reverse the above procedure. Turn the ice maker on
by lowering the ice maker arm.
To Dispense Water:
Hold container under spout and
press dispenser pad.
Water Dispenser (select mode_s)
The Water Dispenser is located on
the left side wall of the fresh food "_7-_,!
section. This design is for cold water
dispensing only. _L
14
HaterFilter(selectmodels)
Water Filter Removal and
Installation
Replacing Water Filter
IMPORTANT: Air trapped in system may cause
water and cartridge to eject. Always dispense
water for at least 2 minutes before removing the
filter for any reason. Use caution when removing.
1. Turn filter counterclockwise until it releases from
filter head.
2. Drain water from filter into sink, and dispose in
normal household trash.
3. Wipe up excess water in filter cover and continue
with Initial Installation, steps 2 through 4.
The filter should be changed at least every 12 months.
IMPORTANT: Condition of water and amount used
determines life span of water filter cartridge. If water
use is high, or if water is of poor quality, replacement
may need to take place more often.
To purchase a replacement water filter cartridge,
contact your dealer or call 1-877-232-6771 U.S.A. or
1-800-688-8/408 Canada.
The dispenser feature may be used without a water
filter cartridge. If you choose this option, replace filter
with blue bypass cap.
State of Cali%rnia
Department of Health Sel_'ices
Initial Installation
The water filter is located in the
upper right-hand corner of the
fresh food compartment.
1. Remove blue bypass cap and
retain for later use.
Water Treatment Device
Certificate Number
03- 1583
Date Issued: September 16, 2003
15
.
.
4.
Remove sealing label from
end of filter and insert into
filter head.
Rotate gently clockwise until
filter stops. Snap filter cover
closed.
Reduce water spurts by
flushing air from system.
Run water continuously for
two minutes through dispenser until water runs
steady. During initial use, allow about a one- to
two-minute delay in water dispersal to allow
internal water tank to fill.
Additional flushing may be required in some
households where water is of poor quality.
At,azine .......
Lmdane
Toxaphene
Rated Service (-:apacit3': 078 _in
Conditions of Certification:
Do not use wh¢I_ _ ate: is microbiologically tmsaf¢ or with ware1 of md¢nown quah1% except that
systems certified for cyst reduction may be used on disinfected waters tha_ may coi_tain filterable
cysts¸
WmerFilter(selectmodels)
System Specification and Performance Data Sheet
Refrigerator Water Filter Cartridge Model UKF8001AXX
Specifications
Service Flow Rate (Maximum) .............................................0.78 GPM (2.9 L/rain)
Rated Service Life UKF8001AXX-750 (Maximum) ......750 gallons/2838 liters
Maximum Operating Temperature .....................................100° F/38 ° C
Minimum Pressure Requirement ........................................35 psi/241 kPA
Minimum Operating Temperature ......................................33° F/1 ° C
Maximum Operating Pressure .............................................120 psi/827 kPA
PentaPure
1000 Apollo Road
Eagan, Minnesota 55121-2240
651.450.4913
EPA EST #35917-MN-1
Performance Data
Parameter
Chlorine
T&O
Particulate _*
100834/B
USEPA
MCL
Standard No. 42: Aesthetic Effects
Influent
Challenge Concentration
2.0 mg/L ± 10%
Min. Required
Reduction
50%
Influent
Average
1.88 mg/L
5,700,000 #/ml
Effluent
Average Maximum
(0.05136364 mg/[ 0.06 mg/L
30,583 #/nil 69,000 #/ml
% Reduction
Average Minimum
>9726% 96.84%
99.52% 98.94%
at least 10,000 particles/ml 85%
Parameter
Turbidity
Cysts
Asbestos
Lead at pH 6.5
Lead at pH 8.5
Mercury at pH 6.5
Mercury at pH 8.5
Atrazine
Benzene
Carbofuran
1,4-Dichlolobenzene
Lindane
Texaphene
USEPA
MCL
1 NTU_*
99.5% Reduction
99% Reduction
0.015 mg/L
0.015 mg/L
0.002 mg/L
0.002 mg/L
0.003 mg/L
0.005 mg/L
0.04 mg/L
0.075 mg/L
0.0002 mg/L
0.003 mg/L
Standard No. 53: Health Effects
Influent
Challenge Concentration
11 ± 1 NTU***
Minimum 5&OOO/L
107108fibers/L; fibers >10 nlicrometers in length
0.15 mg/L + 10%
0.15 mg/L + 10%
.006 mg/L ± 10%
.006 mg/L ± 10%
0.009 mg/L + 10%
0.015 mg/L ± 10%
0.08 mg/L ± 10%
.225 mg/L ± 10%
0.002 mg/L + 10%
0.015 ± 10O/o
Influent
Average
10.7 NTU
16&500 #/L
155 MF/L
0.153 mg/L
0.150 mg/L
0.006 mg/L
0.006 mg/L
0.009 mg/L
0.014 mg/L
0.081 mg/L
0.208 mg/L
0.002 mg/L
0.015 mg/L
Effluent
Average Maximum
0.31 NTU .049 NTU
<1 #/L <1 #/L
<1 MF/L <1 MF/L
<.001 mg/L <.001 mg/L
<.OOl mg/L <.001 mg/L
0.0003 mg/L 0.0005 mg/L
0.0008 mg/L 0.0015 mg/L
<0.002 mg/L 0.002 mg/L
0.0006 mg/L 0.0011 mg/L
<0.001 mg/L <0.001 mg/L
<0.0005 mg/L <0.0005 mg/L
0.0O0 mg/L <0.0001 mg/L
<0.001 mg/L <0.001 mg/L
% Reduction
Average Minimum
9709% 95.20%
>99.99% >99.99%
>99.99O/o >99.99%
>99.35% >9929%
>99.33% >99.29%
95.70% 90.91%
86.22O/o 75.93o/o
76,99% 75.310/o
95.71% 92.14%
98.74% 98.46%
99.76% 99.74%
98.72% 96.50%
92.97O/o 91.67%
Min. Required
Reduction
0.5 NTU
>99.95%
99%
0.10 mg/L
0.10 mg/L
0.002 mg/L
0.002 mg/L
0.003 mg/L
0.005 mg/L
0.04 mg/L
0.075 mg/L
0.0002 mg/L
0.003 mg/L
* Tested using a flow rate of 0.78 gpm; pressure of 60 psig; pH of 75 + 0.5; temp. of
68 ° + 5° F (20 ° + 3 ° C)
** Measurement in Particles/mL Particles used were 0.5 - 1 microns
*** NTU - Nephelometric Turbidity Units
Tested and certified by NSF International against ANSI/NSF Standards 42 & 53
in models UKF8001AXX-750 for the reduction of:
Standard No. 42: Aesthetic Effects Standard No. 53: Health Effects
Taste and Odo_ Reduction Cbenlical Reduction Unit
Chlorine Taste & Odor Lead, Atrazine, Lindane, Benzene,
Mechanical Filtration Unit Carbofuran, 1,4-DichloTobenzene,
Particulate Reduction Class 1 Mercury & Toxaphene Reduction
Mechanical Filtration Unit
Cyst, Turbidity and Asbestos Reduction
General Use Conditions
Read this Performance Data Sheet and compare the
capabilities of this unit with your actual water
treatment needs.
DO NOT use this product where water is microbic-
logically unsafe or of unknown quality without
adequate disinfection before or after the system.
System certified for cyst reduction may be used on
disinfected water that may contain filterable cysts.
USE ONLY WITH COLD WATER SUPPLY. CHECK
FOR COMPLIANCE WITH THE STATE AND LOCAL
LAWS AND REGULATIONS.
The PuriClean ®II retractable water filtration system
uses a UKF8001AXX replacement cartridge. Timely
replacement of filter cartridge is essential for
performance satisfaction from this filtration system.
Please refer to the applicable section of your Use &
Care Guide for general operation, maintenance
requirements and troubleshooting.
This system has been tested according to ANSI/NSF 42
and 53 for reduction of the substance listed above. The
concentration of the indicated substances in water
entering the system was reduced to a concentration less
than or equal to the permissible limit for water leaving
the system, as specified in ANSI/NSF 42 and 53.
16
17
FoodStorugeTips
Fresh Food Storage
The fresh food compartment of a refrigerator should
be kept between 340-40 ° F (1°-4 ° C) with an
optimum temperature of 37° F (3° C). To check the
temperature, place an appliance thermometer in a
glass of water and place in the center of the
refrigerator. Check after 24 hours. If the temperature
is above 40° F (4° C) adjust the controls as explained
on page 10.
Avoid overcrowding the refrigerator shelves. This
reduces the circulation of air around the food and
results in uneven cooling.
Fruits and Vegetables
Storage in the crisper drawers traps humidity to help
preserve the fruit and vegetable quality for longer
time periods (see page 12).
Sort fruits and vegetables before storage and use
bruised or soft items first. Discard those showing
signs of decay.
Always wrap odorous foods such as onions and
cabbage so the odor does not transfer to other foods.
While vegetables need a certain amount of humidity
to remain fresh, too much humidity can shorten
storage times (especially leafy vegetables). Drain
vegetables well before storing.
Wait to wash fresh produce until right before use.
Meat and Cheese
Raw meat and poultry should be wrapped securely
so leakage and contamination of other foods or
surfaces does not occur.
Occasionally mold will develop on the surface of
hard cheeses (Swiss, Cheddar, Parmesan). Cut off at
least an inch around and below the moldy area. Keep
your knife or instrument out of the mold itself. Do not
try to save individual cheese slices, soft cheese,
cottage cheese, cream, sour cream or yogurt when
mold appears.
Dairy Food
Most dairy foods such as milk, yogurt, sour cream
and cottage cheese have freshness dates on their
cartons for appropriate length of storage. Store these
foods in the original carton and refrigerate
immediately after purchasing and after each use.
Frozen Food Storage
The freezer compartment of a refrigerator should be
kept at approximately F (-18 ° C). To check the
temperature, place an appliance thermometer
between the frozen packages and check after 2/4
hours. If the temperature is above F (-18 ° C),
adjust the control as described on page 10.
A freezer operates more efficiently when it is at least
two-thirds full.
Packaging Foods for Freezing
To minimize dehydration and quality deterioration use
aluminum foil, freezer wrap, freezer bags or airtight
containers. Force as much air out of the packages as
possible and be sure they are tightly sealed. Trapped
air can cause the food to dry out, change color and
develop an off-flavor (freezer burn).
Overwrap fresh meats and poultry with suitable
freezer wrap prior to freezing.
Do not refreeze meat that has completely thawed.
Loading the Freezer
Avoid adding too much warm food to the freezer at
one time. This overloads the freezer, slows the rate of
freezing and can raise the temperature of frozen
foods.
Leave space between the packages so cold air can
circulate freely, allowing food to freeze as quickly as
possible.
Avoid storing hard-to-freeze foods such as ice cream
and orange juice on the freezer door shelves. These
foods are best stored in the freezer interior where the
temperature varies less with door openings.
Refer to the Food Storage Chart on pages 18 and 19 for
approximate storage times.
FoodStorageTips
Food Storage Chart
Storage times are approximate and may vary depending on type of packaging, storage temperature, and the quality
of the food when purchased.
_[JIWlD_
DAI RY PRODUCTS
Butter 1 month 6 to 9 months Wrap tightly or cover.
Milk and cream 1 week Not recommended Check carton date. Close tightly.
Don't return unused portions to
original container. Don't freeze
cream unless whipped.
Cream cheese, cheese 1 to 2 weeks Not recommended Wrap tightly.
spread and cheese food
Cottage cheese 3 to 5 days Not recommended Store in original carton.
Check carton date.
Sour cream 10 days Not recommended Store in original carton.
Check carton date.
Hard cheese 1 to 2 months 4 to 6 months Wrap tightly.
(Swiss, Cheddar and Parmesan) May become Cut off any mold.
crumbly
EGGS
Eggs in the shell 3 weeks Not recommended Refrigerate small ends down.
Leftover yolks or whites 2 to/4 days 9 to 12 months For each cup of yolks to be frozen,
add 1 tsp. sugar for use in sweet, or
1 tsp. salt for non-sweet dishes.
FRUITS
Apples 1 month 8 months (cooked) May also store unripe or hard apples
at 60° to 70° F (16° to 21° (3).
Bananas 2 to/4 days 6 months Ripen at room temperature before
(whole/peeled) refrigerating. Note: Bananas will
darken when refrigerated.
Pears, plums, avocados 3 to/4 days Not recommended Ripen at room temperature before
refrigerating. Note: Avocados will
darken when refrigerated.
Berries, cherries, apricots 2 to 3 days 6 months Ripen at room temperature before
refrigerating.
Grapes 3 to 5 days 1 month (whole) Ripen at room temperature before
refrigerating.
Citrus fruits 1 to 2 weeks Not recommended May also store at 60° to 70° F
06 ° to 21° C).
If refrigerated, store uncovered.
Pineapples, cut 2 to 3 days 6 to 12 months Will not ripen after purchase.
Use quickly.
18
FoodStorugeTips
19
VEGETABEES
Asparagus 1 to 2 days 8 to 10 months Do not wash before refrigerating.
Store in crisper.
Brussels sprouts, broccoli, 3 to 5 days 8 to 10 months Wrap odorous foods.
cauliflower, green peas, Leave peas in pods.
lima beans, onions, peppers
Cabbage, celery 1 to 2 weeks Not recommended Wrap odorous foods and refrigerate
in crisper.
7 to 10 days 8 to 10 months Remove tops. Wrap odorous foods
and refrigerate in the crisper.
7 to 10 days Not recommended
Carrots, parsnips, beets and
turnips
Lettuce
POUETRY and FUSH
Chicken and Turkey, whole
Chicken and Turkey, pieces
Fish
I to 2 days
I to 2 days
I to 2 days
12 months
9 months
2 to 6 months
Keep in original packaging for
refrigeration. Place in the meat and
cheese drawer. When freezing longer
than two weeks, overwrap with
freezer wrap.
M EATS
Bacon 7 days 1 month
Beef or lamb, ground 1 to 2 days 3 to 4 months Fresh meats can be kept in original
packaging for refrigeration.
Beef or lamb, roast and steak 3 to 5 days 6 to 9 months Place in the meat and cheese drawer.
When freezing longer than two
weeks, overwrap with freezer wrap.
Ham, fully cooked, whole 7 days 1 to 2 months
half 5 days 1 to 2 months
slices 3 days 1 to 2 months
Luncheon meat 3 to 5 days 1 to 2 months Unopened, vacuum-packed luncheon
meat may be kept up to two weeks
in the meat and cheese drawer.
Pork, roast 3 to 5 days 4 to 6 months
Pork, chops 3 to 5 days 4 months
Sausage, ground 1 to 2 days 1 to 2 months
Sausage, smoked 7 days 1 to 2 months
Veal 3 to 5 days 4 to 6 months
Frankfurters 7 days 1 month Processed meats should be tightly
wrapped and stored in the meat and
cheese drawer.
Sources: United States Department of Agriculture; Food Marketing Institute; Cooperative Extension Service, Iowa
State University
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88

Maytag MFD2560HEB Mode d'emploi

Catégorie
Frigos
Taper
Mode d'emploi
Ce manuel convient également à

dans d''autres langues