Electrolux EHD80170P Manuel utilisateur

user manual

notice d’utilisation

gebruiksaanwijzing

Induction hob

Table de cuisson

vitrocéramique à induction

Inductiekookplaat

EHD 80170 P

2 electrolux

Contents

Safety instructions.................................. 3

Description of the Appliance .................. 4

Operating the appliance......................... 6

Tips on Cooking and Frying ................... 14

Cleaning and Care ................................. 17

What to do if … ..................................... 18

Disposal ................................................ 21

Installation Instructions .......................... 22

Service.................................................. 23

Assembly ge ......................................... 68

Rating Plate........................................... 71

Electrolux. Thinking of you.

Share more of our thinking at www.electrolux.com

5

Subject to change without notice

T

he following symbols are used in this user information:

1

Warning! This must be read! Important advice for the safety of persons and information

on avoiding damage to the appliance

3 General information and advice

2 Information on environmental protection

z Dangerous voltage

electrolux 3

1 Safety instructions

Please comply with these instructions. If you

do not, any damage resulting is not covered

by the warranty.

Correct use

• This appliance is not intended for use by

children or other persons whose physi-

cal, sensory or mental capabilities or

lack of experience and knowledge pre-

vents them from using the appliance

safely without supervision or instruction

by a responsible person to ensure that

they can use the appliance safely.

• Do not leave the appliance unattended

during operation.

• This appliance should be used only for

normal domestic cooking and frying of

food.

• The appliance must not be used as a

work surface or as a storage surface.

• Additions or modifications to the appli-

ance are not permitted.

• Do not place or store flammable liquids,

highly inflammable materials or fusible

objects (e.g. plastic film, plastic, alumin-

ium) on or near the appliance.

Children’s safety

• Small children must be kept away from

the appliance.

• Only let bigger children work on the ap-

pliance under supervision.

• To avoid small children and pets unin-

tentionally switching the appliance on,

we recommend activation of the child

safety device.

General safety

• The appliance may only be installed and

connected by trained, registered service

engineers.

• Built-in appliances may only be used af-

ter they have built in to suitable built-in

units and work surfaces that meet

standards.

• In the event of faults with the appliance

or damage to the glass ceramic (cracks,

scratches or splits), the appliance must

be switched off and disconnected from

the electrical supply, to prevent the pos-

sibility of an electric shock.

• Repairs to the appliance must only be

carried out by trained registered service

engineers.

Safety during use

• Remove stickers and film from the glass

ceramic.

• There is the risk of burns from the appli-

ance if used carelessly.

• Cables from electrical appliances must

not touch the hot surface of the appli-

ance or hot cookware.

• Overheated fats and oils can ignite very

quickly. Warning! Fire hazard!

• Switch the cooking zones off after each

use.

• Users with implanted pacemakers

should keep their upper body at least

30 cm from induction cooking zones

that are switched on.

• Risk of burns! Do not place objects

made of metal, such as knives, forks,

spoons and saucepan lids on the cook-

ing surface, as they can get hot.

Safety when cleaning

• For cleaning, the appliance must be

switched off and cooled down.

• For safety reasons, the cleaning of the

appliance with steam jet or high-pres-

sure cleaning equipment is not permit-

ted.

How to avoid damage to the appliance

• The glass ceramic can be damaged by

objects falling onto it.

• The edge of the glass ceramic can be

damaged by being knocked by the

cookware.

• Cookware made of cast iron, cast alu-

minium or with damaged bottoms can

scratch the glass ceramic if pushed

across the surface.

• Objects that melt and things that boil

over can burn onto the glass ceramic

and should be removed straightaway.

• Do not use the cooking zones with emp-

ty cookware or without cookware.

• To avoid damaging cookware and glass

ceramics, do not allow saucepans or

frying pans to boil dry.

• The ventilation gap of 5mm between the

worktop and front of the unit underneath

it must not be covered.

4 electrolux

Description of the Appliance

Cooking surface layout

Control panel layout

Induction cooking zone 1800 W

with power function 2800 W

Induction cooking zone 2400 W

with power function 3700 W

Induction cooking zone 1800 W

with power function 2800 W

Control panelInduction cooking zone 1400 W

with power function 1800 W

On/Off

with indicator

Timer display

Cooking zone indicators

Timer function

Child lock with

display

Timer

STOP+GO

with indicator

Heat setting selection

Power function Heat setting indicator

Residual heat indicator

Pan recognition and automatic

switch-off indicator

electrolux 5

Touch Control sensor fields

The appliance is operated using Touch Con-

trol sensor fields. Functions are controlled by

touching sensor fields and confirmed by dis-

plays and acoustic signals.

Touch the sensor fields from above, without

covering other sensor fields.

Displays

Sensor field Function

On / Off To switch the appliance on and off

Lock Locking/unlocking the control panel

Stop+Go To switch the Keep Warm setting on/off

Cooking zone Off To switch off the cooking zone

1-9 /

Heat settings To set heat settings

Power Switching the power function on and off

Timer Timer selection

Increase settings To increase Timer time

Reduce settings To reduce Timer time

Display Description

Residual heat Cooking zone is still hot

+

number

Fault Malfunction has occurred

Pan detection Cookware is unsuitable or too small or no

cookware has been placed on the cooking

zone

Automatic switch off Switch off is active.

6 electrolux

Residual heat indicator

1 Warning: Risk of burns from residual

heat. After being switched off, the cook-

ing zones take some time to cool down.

Look at the residual heat indicator .

Control bar

The heat setting and the power function are

set via the control bar. The heat setting indi-

cator consists of a chain of light elements.

3 If the control bar is touched for longer

than 6 seconds, a signal sounds and the

appliance switches itself off.

The induction cooking zones create the

heat required for cooking directly in the base

of the cookware. The glass ceramic is merely

heated by the residual heat of the cookware.

The cooling fan switches itself on and off

depending upon the temperature of the elec-

tronics.

Operating the appliance

3 Use the induction cooking zones with

suitable cookware.

Switching the appliance on and off

Power function indicator

Operational readiness

indicator for cooking zone

Power function

Heat setting indicator

Heat setting selection

Cooking zone Off

Control panel Display

To switch on Touch for 1 second lights up. The opera-

tional readiness indica-

tors of the individual

cooking zones also

light up.

To switch off Touch for 1 second goes out. The opera-

tional readiness indica-

tors of the individual

cooking zones also go

out.

electrolux 7

3 After switching on, within approx.

10 seconds a heat setting or a function

must be set, otherwise the appliance

automatically switches itself off.

Setting the heat setting

The control bar is touched where the desired

heat setting is positioned. The heat setting is

shown in the display. Correct to the left or the

right, if necessary.

Do not release before the desired heat set-

ting is reached.

Locking/unlocking the control panel

The control panel, with the exception of the

“On/Off” sensor field, can be locked at any

time in order to prevent the settings being

changed e.g. by wiping over the panel with a

cloth.

3 When you switch the appliance off, the

locking function is automatically

switched off.

Control panel Display

To switch on Touch lights up

To switch off Touch goes out

8 electrolux

Turning the STOP+GO function

on and off

The STOP+GO function simultaneously tog-

gles all active cooking zones to keep-warm

mode then back to the heat setting they

were at before.

3 STOP+GO does not stop timer func-

tions.

3 STOP+GO controls the entire control

panel apart from the sensor field .

Using the automatic warm-up

function

All cooking zones are equipped with an au-

tomatic warm-up function. When setting a

heat setting using the automatic warm-up

function, the cooking zone switches to full

power for a certain amount of time and then

automatically switches back to the heat set-

ting set.

The length of time that the automatic warm

up function operates depends on the heat

setting selected.

Control panel Display

To switch on Touch Keep-warm setting

To switch off Touch Previous heat setting (not automatic

warm-up or power function)

Step Control panel Display

1. Select warm-up setting display flashes

2. Select the desired heat setting between 1

and 8

The desired heat setting is dis-

played. display lights up.

As long as the

display is lit,

the appliance is working at full

power.

After the automatic warm-up is

completed, the display goes

out.

electrolux 9

Using the child safety device

The child safety device prevents unintention-

al use of the appliance.

Switching on the child safety device

Switching off the child safety device

3 The child safety device can only be

switched on and off, if no heat setting is

set.

Heat setting Warm-up time

[min:sec]

1 0:10

2 0:10

3 3:10

4 5:50

5 10:10

6 2:00

7 2:30

8 2:50

9 ---

Step Control panel Pilot light

1. Switch on appliance. (Do not set a heat

setting.)

lights up. The operational readi-

ness indicators of the individual

cooking zones light up.

2. To uc h for 4 seconds over lights up

The child safety device is switched on

Step Control panel Pilot light

1. Switch on appliance. (Do not set a heat

setting.)

above lights up

2. To uc h for 4 seconds above goes out

3. Switch appliance off.

The child safety device is switched off.

10 electrolux

Overriding the child safety device

The child safety device can be switched off

in this way for a single cooking session; it re-

mains activated afterwards.

3 After overriding the child safety device, a

heat setting or a function must be set

within approx. 10 seconds, otherwise

the appliance automatically switches it-

self off.

Switching the power function on

and off

The power function makes more power

available to the induction cooking zones, e.g.

to bring a large quantity of water to the boil

quickly.

The power function is activated for 10 min-

utes at most. After that the induction cooking

zone automatically switches back to heat

setting 9.

3 If the power function has ended, the

cooking zones automatically switch

back to the heat setting set previously.

Step Control panel Pilot light

1. Switch appliance on over lights up

2. Touch for 4 seconds over goes out.

Until the appliance is next switched off, it can used as normal. The child safety device is still

active after switching off.

Control panel Display

To switch on Touch The light elements in the

control bar light up. The

display flashes

To switch off Select the heat setting

1-9

The heat setting selected is

shown in the display. The

display above

will go out.

electrolux 11

Power Management

The cooking zones of the cooking surface

have a maximum power.

The maximum power is reached when the

heat setting 9 has been set for all cooking

zones.

Two cooking zones generate a pair (see fig-

ure) and therefore, the power management

shares the maximum available power be-

tween these cooking zones.

When the power function is selected for one

cooking zone, the power management

makes the additional power for this cooking

zone available by reducing the power of the

corresponding other cooking zone.

Example: the heat setting 9 is selected on

one cooking zone. The power function is

switched on for the corresponding cooking

zone. The power function is carried out but

the heat setting 9 of one of the cooking

zones and the power function for the other

cooking zone of the pair exceed the maxi-

mum power for both at the same time. For

this purpose, the power management reduc-

es the power of the cooking zone that

switched on first from 9 to example 5 and the

display of this cooking zone changes be-

tween 9 and 5 and then stays at the current

possible maximum 5. (If the display changes

between 9 and 5 or 9 and 3 or another value

depends on the type of appliance and the

size of the cooking zone.).

Using the timer

3 If just one countdown value is set you

can change it only when the appliance is

switched on.

3 If a heat setting is set on this cooking

zone in addition to a countdown timer,

the cooking zone is switched off after

the time set has elapsed.

3 If a cooking zone is switched off, the

timer function set is also switched off.

Function Condition Outcome after the time

has elapsed

Automatic cut-out a heat setting is set acoustic signal

00 flashes

Cooking zone switches off

Countdown timer cooking zones not in use acoustic signal

00 flashes

12 electrolux

Selecting a cooking zone

3 If other timer functions are set, after a

few seconds the shortest remaining

time of all the timer functions is dis-

played and the corresponding pilot light

flashes.

Setting the time

Switching off the timer function

Step Control panel Display

1. Touch once Pilot light of the first cooking zone

flashes

2. Touch once Pilot light of the second cooking

zone flashes

3. Touch once Pilot light of the third cooking

zone flashes

4. Touch once Pilot light of the fourth cooking

zone flashes

Step Control panel Indicator

1. Select cooking zone Pilot light for the cooking zone selected flashes

2. Touch or 00 to 99 minutes

After a few seconds the pilot light flashes more slowly.

The time is set.

The time counts down.

Step Control panel Indicator

1. Select cooking zone Pilot light of cooking zone selected flashes faster

Time remaining is displayed

2. Touch The time remaining counts backwards to 00.

The pilot light goes out.

The Timer function for the selected cooking zone is switched off.

electrolux 13

Changing the time

Displaying the time remaining for a cooking zone

Switching off the acoustic signal

Automatic switch off

Cooking surface

• If after switching on the cooking surface,

a heat setting is not set for a cooking

zone within approx. 10 seconds, the

cooking surface automatically switches

itself off.

• If one or more sensor fields are covered

by objects (a pan, etc.) for longer than

approx. 10 seconds, a signal sounds

and the cooking surface switches off

automatically.

• If all cooking zones are switched off, the

cooking surface automatically switches

itself off after approx. 10 seconds.

Control panel

• When the appliance is switched off, if

one or more of the sensor fields on the

control panel are covered for more that

10 seconds, an acoustic signal sounds.

The acoustic signal switches itself off

automatically when the sensor fields are

no longer covered.

Step Control panel Indicator

1. Select cooking zone Pilot light of the selected cooking zone flashes

faster

Time remaining is displayed

2. Touch or 01 to 99 minutes

After a few seconds, the pilot light flashes more slowly.

The time is set.

The time counts down.

Step Control panel field Display

1. Select cooking zone Pilot light of the cooking zone selected flashes

faster

The time remaining is displayed

After a few seconds the pilot light flashes more slowly.

Step Control panel field Acoustic signal

1. Touch Acoustic signal to acknowledge.

Acoustic signal stops.

14 electrolux

Induction cooking zones

• In the case of overheating (e.g. when a

saucepan boils dry) the cooking zone

automatically switches itself off. is

displayed. Before being used again, the

cooking zone must be set to

0 and

cooled down.

• If cookware that is not suitable is used,

lights up in the display and after

2 minutes the indicator for the cooking

zone switches itself off.

• If one of the cooking zones is not

switched off after a certain time, or if the

heat setting is not modified, the relevant

cooking zone switches off automatically.

is displayed. Before being used

again, the cooking zone must be set to

.

Tips on Cooking and Frying

3 Information on acrylamides

According to the latest scientific knowl-

edge, intensive browning of food, espe-

cially in products containing starch, can

constitute a health risk due to acryla-

mides. Therefore we recommend cook-

ing at the lowest possible temperatures

and not browning foods too much.

Heat setting Switches off after

1 - 2 6 hours

3 - 4 5 hours

5 4 hours

6 - 9 1.5 hours

electrolux 15

Cookware for induction cooking zones

Cookware material

3 * Cookware for induction cooking zones

is labelled as suitable by the manufac-

turer.

Suitability test

Cookware is suitable for induction cooking,

if …

• ... a little water on an induction cooking

zone set to heat setting 9 is heated very

quickly.

• ... a magnet sticks to the bottom of the

cookware.

Cookware base

The bottom of the cookware should be as

thick and flat as possible.

Pan size

Up to a certain limit, induction cooking zones

adapt themselves to the size of the bottom

of the cookware automatically. However, de-

pending on the cooking zone size, themag-

netic part of the bottom of the cookware

must have a minimum diameter.

3 The cookware must be placed centrally

on the cooking zone.

Cookware material suitable

Cast iron +

Steel, enamelled steel +

Stainless steel +*

Multi-layer pan bottom +*

Aluminium, copper, brass -

Glass, ceramic, porcelain -

Diameter of cooking zone

[mm]

Minimum diameter of dish base

[mm]

210 180

180 145

145 120

16 electrolux

Tips on energy saving

2 Place cookware on the cooking zone

before it is switched on.

2 If possible, always place a lid on the

cookware.

Examples of cooking applications

The information given in the following table is for guidance only.

The power function is suitable for heating large quantities of liquid.

Heat

set-

ting

Cooking-

process

suitable for

Cooking

time

Tips/Hints

0 Residual heat, Off position

1

Keeping

food warm

Keeping cooked foods warm as required Cover

1-2

Melting

Hollandaise sauce,

melting butter, chocolate, gela-

tine

5-25 mins. Stir occasionally

Solidifying

Fluffy omelettes, baked eggs 10-40 mins. Cook with lid on

2-3

Simmering

on low heat

Simmering rice and milk-based

dishes

Heating up ready-cooked meals

25-50 mins.

Add at least twice as much

liquid as rice, stir milk dishes

part way through cooking

3-4

Steaming

Braising

Steaming vegetables, fish

braising meat

20-45 mins.

With vegetables add only a

little liquid (a few table-

spoons)

4-5

Boiling

Steaming potatoes 20-60 mins.

Use only a little liquid, e. g.:

max.

¼

l water for

750 g potatoes

Cooking larger quantities of

food, stews and soups

60-150 mins.

Up to 3 l liquid plus ingredi-

ents

6-7

Gentle

Frying

Frying escalopes, veal cordon

bleu, cutlets, rissoles, sausages,

liver, roux, eggs, pancakes,

doughnuts

Steady frying

Turn halfway through cook-

ing

7-8

Heavy

Frying

Hash browns, loin steaks,

steaks, Flädle (pancakes for gar-

nishing soup)

5-15 mins.

per pan

Turn halfway through cook-

ing

9

Boiling

Searing

Deep frying

Boiling large quantities of water, cooking pasta, searing meat (goulash, pot roast),

deep frying chips

electrolux 17

Cleaning and Care

1 Take care! Risk of burns from residual

heat.

1 Warning! Sharp objects and abrasive

cleaning materials will damage the appli-

ance. Clean with water and washing up

liquid.

1 Warning! Residues from cleaning

agents will damage the appliance. Re-

move residues with water and washing

up liquid.

Cleaning the appliance after each use

1. Wipe the appliance with a damp cloth

and a little washing up liquid.

2. Rub the appliance dry using a clean

cloth.

Removing deposits

1. Place a scraper on the glass ceramic

surface at an angle.

2. Remove residues by sliding the blade

over the surface.

3. Wipe the appliance with a damp cloth

and a little washing up liquid.

4. Rub the appliance dry using a clean

cloth.

*Scrapers and cleaners for glass ceramic and stain-

less steel can be purchased in specialized shops

3 Remove stubborn residues with a clean-

er for glass ceramic or stainless steel.

3 Scratches or dark stains on the glass

ceramic that cannot be removed do not

however affect the functioning of the ap-

pliance.

Remove

Type of dirt

imme-

diately

when the appliance has

cooled down

using

sugar, food containing sugar yes ---

a scraper*

plastics, tin foil yes ---

limescale and water rings --- yes

cleaner for glass ceramic

or stainless steel*

fat splashes --- yes

shiny metallic discolouration --- yes

18 electrolux

What to do if …

Problem Possible cause Remedy

The appliance cannot be switched

on or is not operating

More than 10 seconds have

passed since the appliance was

switched on

Switch the appliance on again.

The lock is switched on Switch off the lock (See the sec-

tion “Locking/unlocking the con-

trol panel”)

The child safety device is switched

on

Deactivate child safety device (See

the section “Child safety device”)

Several sensor fields were

touched at the same time

Only touch one sensor field

Automatic switch off has been trig-

gered

Remove any objects (pan, cloths,

etc.) that are lying on the control

panel. Switch the appliance on

again

Dirty control panel The sensor fields must be dry and

fat-free.

The residual heat indicator is not

displaying anything

The cooking zone was only on for

a short time and is therefore not

hot

If the cooking zone is supposed to

be hot, call the Customer Service

Department.

Repeated acoustic signal (6x), ap-

pliance switches off

One or more sensor fields have

been covered for longer than 10

seconds

Uncover sensor field

Acoustic signal sounds when ap-

pliance is switched off

The control panel is wholly or part-

ly covered by objects.

Remove objects.

Acoustic signal sounds and appli-

ance switches itself on and then

off again; after 5 seconds another

acoustic signal sounds

The On/Off sensor field has been

covered up, e.g. by a cloth

Do not place any objects on the

control panel

Display is switching between two

heat settings

Power management is reducing

the power of this cooking zone

See the section “Switching the

power function on and off”

lights up Unsuitable cookware Use suitable cookware

No cookware on the cooking zone Place cookware on the cooking

zone

The diameter of the bottom of the

cookware is too small for the

cooking zone

Move onto a smaller cooking zone

Use suitable cookware

lights up Overheating protection for the

cooking zone has been triggered

Switch off the cooking zone.

Switch the cooking zone on again

Automatic switch-off has been

triggered

Switch appliance off. Switch appli-

ance on again

electrolux 19

If you are unable to remedy the problem

by following the above suggestions,

please contact your local Service Force

Centre.

1 Warning! Repairs to the appliance are

only to be carried out by qualified serv-

ice engineers. Considerable danger to

the user may result from improper re-

pairs.

3 If the appliance has been operated in-

correctly, the engineer's visit will be

chargeable, even during the warranty

period.

and number are displayed Electronics fault Disconnect the appliance from the

electrical supply for a few minutes

(Take the fuse out of the house’s

wiring system)

If after switching on again, is

displayed again, call the customer

service department

Problem Possible cause Remedy

20 electrolux

Operating noises

Depending on the material and the process-

ing of the base, the following noises may oc-

cur when using induction cooking zones.

• Cracking noise (1)

when using cookware made of different

materials (Sandwich construction)

• Whistling (1)

when using an individual cooking zone

or several cooking zones with high pow-

ers when the cookware is made of dif-

ferent materials (Sandwich construction)

• Humming (2)

can occur at high power levels

• Clicking (2)

during electric switching processes

• Hissing, buzzing (3)

The device is fitted with a fan for cooling

the electrics. A whiring noise can be

heard when operating the fan which

may deviate depending on the perform-

ance and may continue for a while after

the appliance is switched off.

The noises described are normal and do

not refer to any defects.

3

2

1

La page charge ...

Electrolux EHD80170P Manuel utilisateur

Electrolux EHD80170P Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents