Whirlpool ACMK 6123/WH Mode d'emploi

Marque: Whirlpool

Modèle: ACMK 6123/WH

Catégorie: Fours

Taper: Mode d'emploi

ACMK 6123/WH ACMK 6123/WH ACMK 6123/WH ACMK 6123/WH

English

Operating Instructions

COOKER AND OVEN

Contents

Operating Instructions,1

Safety ,3

Description of the appliance-Overall view,13

Description of the appliance-Control Panel,13

Installation,14

Start-up and use,18

Cooking modes,19

Using the hob,18

Care and maintenance,22

Français

Mode d’emploi

CUISINIERE ET FOUR

Sommaire

Mode d’emploi,1

Consignes de s'ecurit'e ,8

Description de l’appareil-Vue d’ensemble, 13

Description de l’appareil-Tableau de bord, 13

Installation,24

Mise en marche et utilisation,28

Utilisation du plan de cuisson,28

Nettoyage et entretien,32

EnglishEnglish

Programmes du four,29

SAFETY INSTRUCTIONS

These instructions shall also be available on website: www.whirlpool.eu

YOUR SAFETY AND

This manual and the appliance itself provide important safety warnings, to be read and observed at all times.

Indicates a hazardous situation which, if not avoided, will cause serious injury.

Indicates a hazardous situation which, if not avoided, could cause serious injury.

DANGER

WARNING

Before using the appliance carefully read Health and Safety and Use and Care guides.

Keep these instructions close at hand for future reference.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol or the word “DANGER” or “WARNING.” These words

mean:

IMPORTANT TO BE RED AND OBSERVED

SAFETY OF OTHERS IS VERY IMPORTANT

All safety warnings give specific details of the potential risk presented and indicate how to reduce risk of

injury, damage and electric shock resulting from improper use of the appliance. Carefully observe the

following instructions.

Failure to observe these instructions may lead to risks. The Manufacturer declines any liability for injury to

persons or animals or damage to property if these advices and precautions are not respected.

Very young (0-3 years) and young children (3-8 years) shall be kept away unless continuously

supervised.

Children from 8 years old and above and persons with reduced physical, sensory or mental

capabilities or lack of experience and knowledge can use this appliance only if they are supervised

or have been given instructions on safe appliance use and if they understand the hazards involved.

Children shall not play with the appliance. Cleaning and user maintenance shall not be made by

childern without supervision.

The appliance and its accessible parts become hot during use, young children should be kept

away. Do not allow the appliance to come into contact with cloths or other flammable materials

until all the components have cooled down completely.

During and after use, do not touch the heating elements or interior surface of the appliance - risk of

burns.

Overheated oils and fats catch fire easily. Always remain vigilant when cooking foods rich in fat, oil

or alcohol (e.g. rum, cognac, wine).

Never leave the appliance unattended during food drying.

WARNING : Do not heat or cook with sealed jars or containers in the appliance.

The pressure that builds up inside might cause them to explode, damaging the appliance.

If alcoholic beverages are used when cooking foods (e.g. rum, cognac, wine), remember that

alcohol evaporates at high temperatures. As a result, there is a risk that vapours released by the

alcohol catch fire if coming in contact with the electrical heating element.

If the appliance is suitable for probe usage, Only use the temperature probe recommended for this

oven.

DANGER OF FIRE : Do not store items on the cooking surfaces since they can catch fire.

CAUTION : In case of hotplate glass breakage:-shut immediately off all burners and any electrical

heating element and isolate the appliance from the power supply; - do not touch the appliance

surface; -do not use the appliance

These instructions are valid if the country symbol appears on the appliance. If the symbol doesn't

appear on the appliance, it is necessary to refer to the technical instructions which will provide the

necessary instructions concerning modification of the appliance to the conditions of use of the

country

The glass lid can break in if it is heated up. Turn off all the burners and the electric plates before

closing the lid. Do not shout down lid when burner alight

If the information in this manual is not followed exactly, a fire or explosion , may result causing

property damage or injury.

INTENDED USE OF THE PRODUCT

This appliance is designed solely for domestic usage. No other use is permitted (e.g. heating

rooms). To aim the appliance as professional use is forbidden. The manufacturer declines all

responsibility for innapropriate

use or incorrect setting of the controls.

This appliance is intended to be used in household and similar applications such as :

Staff kitchen areas in shops, offices and other working environments;

Farm houses;

By clients in hotels, motels and other residential environments;

Bed and breakfast type environments.

CAUTION : The appliance is not intended to be operated by means of an external timer or separate

remote controlled supply system.

Do not use the appliance outdoors.

Do not store explosive or flammable substances such as aerosol cans and do not place or use

gasoline or other flammable materials in or near the appliance: a fire may break out if the

appliance is inadvertently switched on.

INSTALLATION

Installation and repairs must be carried out by a qualified technician, in compliance with the

manufacturer's instructions and local safety regulations. Do not repair or replace any part of the

appliance unless specifically stated in the user manual.

The electrical and gas connections must comply with local regulation.

Children should not perform installation operations. Keep children away during installation of the

appliance. Keep the packaging materials (plastic bags, polystyrene parts, etc.) out of reach of

children, during and after the installation of the appliance.

WARNING : Modification of the appliance and its method of installation are essential in order to use the

appliance safely and correctly in all the additional countries

Use protective gloves to perform all unpacking and installation operations.

After unpacking the appliance, make sure that the appliance door closes properly. In the event of

problems, contact the dealer or your nearest After-sales Service. To prevent any damage, only

remove the oven from its polystyrene foam base at the time of installation.

The appliance must be handled and installed by two or more persons.

The appliance must be disconnected from the power supply before carrying out any installation

operation.

During installation, make sure the appliance does not damage the power cable.

Only activate the appliance when the installation procedure has been completed.

Kitchen units in contact with the appliance must be heat resistant (min 90°C).

GAS CONNECTION

WARNING : Prior to installation, ensure that the local gas delivery conditions (nature or pressure) are

compatible with the setting of the hob (see the rating plate and injector table).

Use pressure regulators suitable for the gas pressure indicated in the instruction.

WARNING : The adjustment condictions for this appliance are stated on the lable (or data plate).

WARNING : This appliance is not connected to a combustion products evacuation device. It shall be

installed and connected in accordance with current installation regulations. Particulat attention shall

be given to the relevant requirements regarding ventilation.

WARNING : These operations must be perfomed by a qualified technician.

If the appliances is connected to liquid gas, the regulation screw must be fastned as tightly as

possible.

When gas cylinder is adopted, the gas cylinder or gas container must be properly settled (vertical

orientation).

Use only flexible or rigid metal hose for gas connection.

IMPORTANT : If a staineless steel hose is used, it must be installed so as not touch any mobile part

of the furniture (e.g.drawer). It must pass thorugh an area where there are no obstructions and where

it is possible to inspect it on all its length.

After connection to the gas supply, check for leaks with soapy water. Light up the burners and turn

the knobs from max position 1* to minimum position 2* to check flame stability.

ELECTRICAL WARNINGS

Make sure the voltage specified on the rating plate corresponds to that of your home.

For installation to comply with current safety regulations, an omnipolar switch with minimum contact

gap of 3mm is required.

Regulation require that the appliance is earthed.

For appliances with fitted plug, if the plug is not suitable for you socket outlet, contact a qualified

technician.

Do not use extension leads, multiple sockets or adapters. Do not connect the appliance to a socket

which can be operated by remote control.

The power cable must be long enough for connecting the appliance, once fitted in its housing, to the

main power supply.

Do not pull the power supply cable.

If the power cable is damaged it must be replaced with an identical one. The power cable must only

be replaced by a qualified technician in compliance with the manufacturer instruction and current

safety regulations. Contact an authorized service center.

Do not operate this appliance if it has a damaged mains cord or plug, if it is not working properly, or if

it has been damaged or dropped. Do not immerse the mains cord or plug in water. Keep the cord

away from hot surfaces.

The electrical components must not be accessible to the user after installation.

Do not touch the appliance with any wet part of the body and do not operate it when barefoot.

It must be possible to disconnect the appliance from the power supply by unplugging it if plug is

accessible, or by means of an accessible multi-pole switch installed upstream of the socket in

conformity with national electrical safety standards.

The rating plate is on the front edge of the oven (visible when the door is open).

CORRECT USE

CAUTION : The cooking process has to be supervised. A short cooking process has to be

supervised continuously.

Do not use the hob as a work surface or support.

WARNING : Unattended cooking on a hob with fat or oil can be dangerous and may result in fire.

Never try to extinguish a fire with water, but switch off the appliance and then cover flame e.g. with a

lid or a fire blanket.

Use oven gloves to remove pans and accessories, taking care not to touch the heating elements.

IMPORTANT : Should you experience difficulty in turning the burners knobs, please contact After

Sales Service for replacement of the burner tap if found to be faulty.

The openings use for the ventilation and dispersion of heat must never be covered.

Use pots and pans with bottoms the same width as that of the burners or slightly larger (see specific

table). Make sure pots on the grates do not protrude beyond the edge of the hob.

WARNING : Do not let the burner flame extend beyond the edge of the pan

IMPORTANT : Improper use of the grids can result in damage to the hob: do not position the grids

upside down or slide them across the hob.

Do not use : Cast iron griddles, ollar stones, terracotta pots and pans.

Heat diffusers such as metal mesh, or any other types.

Note : should particular local conditions of the delivered gas make the ignition of burner difficult, it is

advisable to repeat the operation with the knob turned to small flame setting.

Note : In case of installation of a hood above the cooktop, please refer to the hood instructions for the

correct distance.

WARNING : The protective rubber feet on the grids represent a chocking hazard for young children.

After removing the grids, please ensure that all the feet are correctly fitted.

Remove any liquid from the lid before opening it

CLEANING AND MAINTANCE

The appliance must be disconnected from the power supply before carrying out any cleaning or

maintenance operation.

Never use steam cleaning equipment.

Ensure that the appliance is switched off before replacing the lamp to avoid the possibility of electric

shock.

Do not use harsh abrasive cleaners or sharp metal scrapers to clean the appliance door glass since

they can scratch the surface, which may result in shattering of the glass.

Do not use abrasive or corrosive products, chlorine-based cleaners or pan scourers.

To avoid damaging the electric ignition device, do not use it when the burners are not in their

housing.

SAFEGUARDING THE ENVIRONMENT

DISPOSAL OF PACKAGING MATERIALS

- The packaging material is 100% recyclable and is marked with the recycle symbol . The various

parts of the packaging must therefore be disposed of responsibility and in full compliance with local

authority regulations governing waste disposal.

SCRAPPING OF HOUSEHOLD APPLIANCES

When scrapping the appliance, make it unusable by cutting off the power cable and removing the

doors and shelves (if present) so that children cannot easily climb inside and become trapped.

This appliance is manufactured with recyclable or reusable materials. Dispose of it in accordance

with local waste disposal regulations.

For further information on the treatment, recovery and recycling of household electrical appliances,

contact your competent local authority, the collection service for household waste or the store where

you purchase the appliance.

This appliance is marked in compliance with European Directive 2012/19/EU, Waste Electrical and

Electronic Equipment (WEEE).

By ensuring this product is disposed of correctly, you will help prevent potential negative

consequences for the environment and human health, which could otherwise be caused by

inappropriate

waste

handling

this

product.

The symbol

on the product or on the accompanying documentation indicates that it should not be

treated as domestic waste but must be taken to an appropriate collection center for the recycling of

electrical and electronic equipment.

Only preheat the oven if specified in the cooking table or your recipe.

Use dark lacquered or enamelled baking moduls as they absorb heat far better.

Switch the oven off 10/15 minutes before the set cooking time. Food requiring prolonged cooking will

continue to cook even once the oven is switched off."

ENERGY SAVING TIPS

This appliance meets the Eco Design requirements of European Regulations n. 65/2014, and n.

66/2014 in conformity to the European standard EN 60350-1.

DECLARATION OF CONFORMITY

AFTER-SALES SERVICE

Before calling the After-Sales Service

1. See if you can eliminate the problem on your own (see “Troubleshooting Guide”).

2. Switch the appliance off and on again to see if the problem persists.

If the fault persists after the above checks, contact your nearest After-Sales Service.

Specify: the type of fault;

• exact type and model of oven;

• the After-Sales Service number (the number given after the word “Service” on the dataplate) located inside

the storage compartment flap. The service number is also given in the warranty booklet;

• your full address;

• your telephone number.

For repairs, contact an Authorised After-Sales Service, indicated in the warranty.

If any work is carried out by technicians not belonging to the Manufacturer's authorised After-Sales Service

centres, request a receipt specifying the work performed and make sure the replacement parts are original.

Failure to comply with these instructions can compromise the safety and quality of the product.

Data plate, is located inside the flap or, after the oven

compartment has been opened, on the left-hand wall

inside the oven.

59l

CONSIGNES DE SÉCURITÉ

INSTRUCTIONS IMPORTANTES À LIRE ET À RESPECTER

Avant d'utiliser l'appareil, lisez attentivement les guides de sécurité, d'utilisation et d'entretien. Gardez ces

documents à portée de main pour toute référence future.

Ces instructions sont également disponibles sur le site Web : www.whirlpool.eu

VOTRE SÉCURITÉ ET CELLE D'AUTRUI EST TRÈS IMPORTANTE

Ce manuel et l'appareil lui-même fournissent des avertissements de sécurité importants, à lire et à respecter en tout temps.

Ceci est le symbole d'alerte de sécurité.

Ce symbole vous avertit des risques potentiels de blessures graves ou même de mort qui peuvent survenir pour vous et toute autre personne.

Tous les messages concernant la sécurité seront précédés du symbole d'alerte de sécurité et du mot « DANGER » ou « AVERTISSEMENT ».

Ces mots signifient :

AVERTISSEMENT

Indique une situation dangereuse qui, si elle n'est pas évitée, provoque des blessures graves.

Indique une situation risqu

e qui, si elle n'est pas

vit

e, pourrait entra

ner des blessures graves.

Tous les messages de sécurité donnent des détails spécifiques du risque potentiel présenté et indiquent comment réduire le

risque de lésion, de dommage et de choc électrique résultant d'une mauvaise utilisation de l'appareil. Observez minutieusement

les instructions suivantes.

Le non-respect de ces instructions peut entraîner des risques. Le fabricant décline toute responsabilité en cas de blessure

causée à des personnes ou des animaux et en cas de dommage matériel résultant du non-respect de ces consignes et

précautions.

Les bébés (0-3 ans) et les jeunes enfants (3-8 ans) doivent être tenus à l'écart de l'appareil à moins d'être surveillés

en permanence.

Cet appareil peut être utilisé par des enfants de 8 ans et plus et par des personnes dont les capacités physiques,

sensorielles ou mentales sont réduites ou n'ayant pas suffisamment d'expérience ou de connaissances uniquement si

elles sont supervisées ou ont reçu des instructions relatives à l'utilisation de l'appareil en toute sécurité et si elles

comprennent les risques encourus. Les enfants ne doivent pas jouer avec l'appareil. Le nettoyage et l'entretien par

l'utilisateur ne doivent pas être effectués par les enfants sans surveillance.

L'appareil et ses parties accessibles deviennent chauds pendant l'utilisation. Par conséquent, les jeunes enfants

doivent être tenus à l'écart. Ne laissez l'appareil entrer en contact avec des tissus ou d'autres matériaux inflammables

que lorsque tous les composants ont complètement refroidi.

Pendant et après l'utilisation, ne touchez pas aux éléments chauffants ou à la surface intérieure de l'appareil, afin d'éviter

tout risque de brûlures.

Les huiles et graisses surchauffées prennent feu facilement. Vous devez toujours rester vigilant lors de la cuisson des

aliments riches en graisse, en huile ou en alcool (par exemple, rhum, cognac, vin).

Ne laissez jamais l'appareil sans surveillance pendant le séchage des aliments.

AVERTISSEMENT : Évitez de cuisiner ou de chauffer les aliments sur l'appareil avec les brocs ou récipients fermés.

La pression qui monte à l'intérieur pourrait les faire exploser et endommager l'appareil.

Si les boissons alcoolisées sont utilisées lors de la cuisson des aliments (par exemple, le rhum, le cognac, le vin),

rappelez-vous que l'alcool s'évapore à des températures élevées. En conséquence, il existe un risque que les vapeurs

dégagées par l'alcool prennent feu en cas de contact avec l'élément de chauffage électrique.

Si l'appareil est adapté pour l'utilisation de la sonde, utilisez seulement la sonde de température recommandée pour ce four.

RISQUE D'INCENDIE : N'entreposez pas d'éléments sur les surfaces de cuisson puisqu'elles sont inflammables.

ATTENTION : En cas de cassure du verre de la plaque chauffante : éteignez immédiatement tous les brûleurs et tout

élément chauffant électrique puis débranchez l'appareil ; ne touchez pas la surface de l'appareil ; - n'utilisez pas l'appareil

Ces instructions sont valables si le symbole du pays s'affiche sur l'appareil. Si le symbole ne s'affiche pas sur l'appareil, il est

recommandé de se référer aux instructions techniques qui fourniront les consignes nécessaires relatives à l'adaptation de

l'appareil aux conditions d'utilisation du pays.

Le couvercle en vitre peut se briser s'il est chauffé. Éteignez les brûleurs et les plaques électriques avant de fermer le

couvercle. Ne refermez pas le couvercle lorsque le brûleur est allumé

Si les informations contenues dans ce manuel ne sont pas respectées à la lettre, un incendie ou une explosion

pourraient survenir et causer des dégâts matériels ou des blessures.

USAGE PRÉVU DE L'APPAREIL

Le présent appareil a été conçu à des fins domestiques uniquement. Toute utilisation à des fins autres que celles

prévues est interdite (chauffage de pièces par exemple) Tout usage à des fins professionnelles est interdit. Le

fabricant décline toute responsabilité pour un usage inapproprié ou un réglage incorrect des commandes.

Cet appareil est destiné à un usage domestique et dans des endroits similaires, tels que :

les espaces cuisine dans les boutiques, les bureaux et autres environnements de travail ;

les maisons de campagne ;

les cuisines pour clients dans les hôtels, motels et autres lieux d'habitation ; et

les chambres d'hôtes.

ATTENTION : Cet appareil n'est pas conçu pour être utilisé au moyen d'une minuterie externe ou d'une télécommande

séparée.

N'utilisez pas cet appareil à l'extérieur.

Ne stockez pas des substances explosives ou inflammables telles que les aérosols et ne posez pas ni utilisez

l'essence ou d'autres matériaux inflammables dans ou près de l'appareil. Autrement, cela pourra entraîner un

incendie si l'appareil est mis sous tension par inadvertance.

INSTALLATION

L'installation et les réparations doivent être effectuées par un technicien qualifié, en conformité avec les instructions

du fabricant et les réglementations de sécurité locales. Évitez de réparer ou de remplacer toute pièce de l'appareil

sauf indication contraire dans le mode d'emploi.

Les connexions électriques et de gaz doivent être conformes aux réglementations locales.

Les enfants ne doivent pas effectuer des opérations d'installation. Éloignez les enfants lors de l'installation de

l'appareil. Conservez les matériaux d'emballage (sacs en plastique, éléments en polystyrène, etc.) hors de portée des

enfants, pendant et après l'installation de l'appareil.

AVERTISSEMENT : Toute modification de l'appareil et sa méthode d'installation sont cruciales pour une utilisation correcte et en toute

sécurité de l'appareil dans les autres pays

Utilisez des gants de protection pour effectuer toutes les opérations de déballage et d'installation.

Après avoir déballé l'appareil, assurez-vous que la porte se ferme bien. En cas de problème, contactez votre

revendeur ou le service après-vente le plus proche. Pour éviter tout dommage, retirez le four de son socle en mousse

de polystyrène seulement au moment de l'installation.

L'appareil doit être manipulé et installé par deux personnes ou plus.

Avant d'effectuer toute opération d'installation, assurez-vous de débrancher l'appareil du secteur.

Lors de l'installation, assurez-vous que l'appareil n'endommage pas le câble d'alimentation.

Allumez l'appareil uniquement lorsque la procédure d'installation a été achevée.

Les unités de cuisine en contact avec l'appareil doivent être résistantes à la chaleur (min 90 °C).

CONNEXION DE GAZ

AVERTISSEMENT : Avant l'installation, assurez-vous que les conditions locales de distribution de gaz (nature ou pression) sont

compatibles avec le réglage de la plaque de cuisson (voir la plaque signalétique et le tableau d'injection).

Utilisez des régulateurs de pression adaptés à la pression de gaz indiquée dans les instructions.

AVERTISSEMENT : Les conditions de réglage de cet appareil sont marquées sur l'étiquette (ou la plaque signalétique).

AVERTISSEMENT : Cet appareil n'est pas relié à un dispositif d'évacuation des produits de combustion. Il doit être installé et

relié conformément aux réglementations d'installation en vigueur. Une attention particulière doit être accordée aux exigences

pertinentes concernant la ventilation.

AVERTISSEMENT : Ces opérations doivent être réalisées par un technicien qualifié.

Si l'appareil est relié au gaz liquéfié, la vis de régulation doit être serrée correctement.

Lorsque la bouteille de gaz est adoptée, la bouteille ou le conteneur de gaz doit être correctement positionné(e) (position

verticale).

Utilisez uniquement un tuyau métallique flexible ou rigide pour la connexion de gaz.

IMPORTANT : Si un tuyau en acier est utilisé, il doit être installé de manière à ne toucher aucune partie mobile des meubles

(par exemple le tiroir). Il doit passer à travers une zone exempte d'obstructions et permettant une inspection sur toute sa

longueur.

Après la connexion à l'alimentation en gaz, vérifiez les fuites avec de l'eau savonneuse. Allumez les brûleurs et tournez

La plaque signalétique se trouve sur le bord avant du four (visible lorsque la porte est ouverte).

AVERTISSEMENTS RELATIFS À L'ÉLECTRICITÉ

Assurez-vous que la tension indiquée sur la plaque signalétique correspond à celle de votre maison.

Pour que l'installation soit conforme aux réglementations de sécurité en vigueur, un interrupteur omnipolaire avec

ouverture de contact minimale de 3 mm est nécessaire.

Le règlement exige que l'appareil soit relié à la terre.

Pour les appareils avec prise intégrée, si la fiche ne convient pas à votre prise de courant, contactez un technicien

qualifié.

N'utilisez pas de rallonges, de multiprises ou d'adaptateurs. Ne branchez pas l'appareil à une prise qui peut être

actionnée par télécommande.

Le câble d'alimentation doit être suffisamment long pour relier l'appareil, une fois monté dans son logement, à

l'alimentation principale.

Évitez de tirer sur le câble d'alimentation.

S'il venait à être endommagé, remplacez-le par un câble identique. Le câble d'alimentation doit être remplacé uniquement

par un technicien qualifié, en conformité avec les instructions du fabricant et les normes de sécurité en vigueur. Contactez

un centre de service agréé.

N'utilisez pas cet appareil si le cordon d'alimentation ou la fiche est endommagé, s'il ne fonctionne pas correctement, s'il est

endommagé ou s'il est tombé. Ne plongez pas le cordon d'alimentation ou la fiche dans de l'eau. Éloignez le cordon des

surfaces chaudes.

Les composants électriques ne doivent pas être accessibles à l'utilisateur après l'installation.

Ne touchez pas l'appareil avec une partie du corps mouillée et ne l'utilisez pas pieds nus.

Il est possible de déconnecter l'appareil de l'alimentation électrique en le débranchant si la prise est accessible, ou au

moyen d'un commutateur multipolaire accessible installé en amont de la prise en conformité avec les normes de

sécurité électriques nationales.

UTILISATION APPROPRIÉE

ATTENTION : Le processus de cuisson doit être supervisé. Une cuisson de courte durée doit être surveillée en permanence.

N'utilisez pas la table de cuisson comme surface de travail ou appui.

AVERTISSEMENT : Une cuisson sans surveillance sur une plaque de cuisson avec de la graisse ou de l'huile peut être

dangereuse et peut causer un incendie. N'essayez jamais d'éteindre un incendie avec de l'eau. Arrêtez plutôt l'appareil et

ensuite couvrez les flammes par exemple avec un couvercle ou une couverture anti-feu.

Utilisez des gants de cuisine pour sortir les casseroles et les accessoires, en prenant soin de ne pas toucher les éléments chauffants.

IMPORTANT : S'il vous est difficile de tourner les boutons du brûleur, veuillez contacter le service après-vente pour le

remplacement du brûleur en cas de défaillance.

Les orifices utilisés pour la ventilation et la dispersion de la chaleur ne doivent jamais être obstrués.

Utilisez des marmites et des casseroles dont la largeur est égale ou légèrement supérieure à celle des brûleurs (voir le

tableau spécifique). Assurez-vous que les marmites sur les grillages ne dépassent pas les limites de la plaque de cuisson.

AVERTISSEMENT : Ne laissez pas la flamme du brûleur dépasser le bord de la casserole

IMPORTANT : Un usage inapproprié des grilles peut endommager la plaque de cuisson : ne posez pas les grilles à

l'envers ou ne les faites pas glisser sur la plaque de cuisson.

N'utilisez pas : de plaques de gril en fonte, de pierres ollaires, de marmites et de casseroles en terre cuite ;

des diffuseurs de chaleur tels que les grillages métalliques, ou tout autre type ;

Remarque : lorsque les conditions locales particulières du gaz distribué rendent l'allumage du brûleur difficile, il est

recommandé de répéter l'opération avec le bouton tourné à la position de réglage de petite flamme.

Remarque : En cas d'installation d'une hotte au-dessus de la table de cuisson, referez-vous aux instructions de la hotte pour la

distance adéquate.

AVERTISSEMENT : Les pieds de protection en caoutchouc sur les grilles représentent un danger pour les jeunes enfants.

Après le retrait des grilles, assurez-vous que tous les pieds sont correctement fixés.

Essuyez tout liquide sur le couvercle avant de l'ouvrir.

NETTOYAGE ET ENTRETIEN

Avant d'effectuer toute opération de nettoyage ou d'entretien, assurez-vous de débrancher l'appareil du secteur.

N'utilisez jamais un équipement de nettoyage à vapeur.

Assurez-vous de débrancher l'appareil avant de remplacer l'ampoule pour éviter tout risque de choc électrique.

N'utilisez jamais de produits abrasifs ou les grattoirs métalliques pour nettoyer la porte de l'appareil, ils pourraient enrayer

la vitre et elle pourrait se briser.

N'utilisez pas de produits abrasifs ou corrosifs, de produits à base de chlore ou de tampons à récurer.

Pour éviter tout dommage du dispositif d'allumage électrique, ne l'utilisez pas lorsque les brûleurs ne sont pas dans

leur logement.

PROTECTION DE L'ENVIRONNEMENT

ÉLIMINATION DES MATÉRIAUX D'EMBALLAGE

- Le matériau d'emballage est 100 % recyclable et est marqué du symbole de recyclage Les différentes parties de

l'emballage doivent donc être éliminées en toute responsabilité et en pleine conformité avec

la réglementation de l'autorité locale sur l'élimination des déchets

MISE AU REBUT DES APPAREILS ÉLECTROMÉNAGERS

Lors de la mise au rebut de l'appareil, rendez-le inutilisable en coupant le câble d'alimentation et en démontant les

portes et les grilles (si présente) afin que les enfants ne puissent y grimper facilement et se coincer à l'intérieur.

Cet appareil est fabriqué à partir des matériaux recyclables ou réutilisables. Mettez-le au rebut conformément à la

réglementation d'élimination des déchets locaux.

Pour de plus amples renseignements sur le traitement, la récupération et le recyclage des appareils électroménagers,

contactez votre autorité locale compétente, le service de collecte des déchets ménagers ou le magasin où vous achetez

l'appareil.

Cet appareil est marqué conformément à la Directive 2012/19/CE du Parlement européen relative aux déchets

d’équipements électriques et électroniques.

En assurant la bonne évacuation de ce produit vous pourrez éviter tous risques de conséquences négatives

pour l'environnement et la santé humaine causées par l'élimination incorrecte de ce produit.

Le symbole sur le produit ou sur la documentation d'accompagnement indique qu'il ne doit pas être

traité comme des ordures ménagères mais plutôt emmené à un centre spécialisé de collecte d'ordure pour le recyclage des

équipements électriques et électroniques.

CONSEILS POUR ÉCONOMISER DE L'ÉNERGIE

Ne préchauffez le four que cela est spécifié dans la table de cuisson ou votre recette.

Utilisez des modules de cuisson laqués ou émaillés sombres étant donné qu'ils absorbent beaucoup mieux la chaleur.

Éteignez le four 10/15 minutes avant le temps de cuisson défini. Les aliments nécessitant une cuisson prolongée continue

de cuire à même lorsque que le four est éteint.

DÉCLARATION DE CONFIRMITÉ

Cet appareil répond aux exigences d'éco-conception de la directive européenne n

65/2014, et n

66/2014 en conformité avec la norme européenne EN 60350-1

La plaque signalétique est située à l'intérieur du rabat ou, après

l'ouverture du compartiment du four, sur le mur gauche à

l'intérieur du four.

SERVICE APRÈS-VENTE

Avant d'appeler le service après-vente

Voyez si vous pouvez résoudre le problème par vous-même (voir « Guide de dépannage »).

2. Éteignez l'appareil et rallumez-le pour voir si le problème persiste.

Si le défaut persiste après les vérifications ci-dessus, contactez votre service après-vente le plus proche.

Précisez : le type d'anomalie ;

•

le type et le modèle exacts du four ;

•

le numéro du service après-vente (le numéro indiqué après le mot « service » sur la plaque signalétique) situé à l'intérieur du rabat

du compartiment de rangement. Le numéro du service est également mentionné dans le livret de garantie ;

•

votre adresse complète ;

•

votre numéro de téléphone.

Pour les réparations, contactez un

Service après-vente agréé

, indiqué dans la garantie.

Si des travaux sont effectués par des techniciens ne relevant pas des centres de service après-vente autorisés du fabricant,

demandez un reçu précisant le travail effectué et assurez-vous que les pièces de rechange sont d'origine.

Le non-respect de ces

instructions peut compromettre la sécurité et la qualité du produit.

59l

1 Hob burner

2 Hob Grid

3.Control panel

4.Sliding grill rack

5.DRIPPING pan

6.Adjustable foot

7.Containment surface for spills

8.GUIDE RAILS for the sliding racks

9.position 5

10.position 4

11.position 3

12.position 2

13.position 1

Description of the appliance

Overall view

1.Brûleur à gaz

2.Grille du plan de cuisson

3.Tableau de bord

4. Support GRILLE

5. Support LECHEFRITE

6.Pied de réglage

7.Plateau du plan de cuisson

8. GLISSIERES de coulissement

9. niveau 5

10.niveau 4

11.niveau 3

12.niveau 2

13.niveau 1

Description de l’appareil

Vue d’ensemble

Description of the appliance

Control panel

3.THERMOSTAT knob

1.SELECTOR knob

2.THERMOSTAT Indicator light

4.Hob BURNER control knob

Description de l’appareil

Tableau de bord

3.Manette du THERMOSTAT

2.Voyant lumineux THERMOSTAT

1.Manette PROGRAMMES

4.Manette BRULEURS

Room ventilation

The appliance may only be installed in permanently-

ventilated rooms, in accordance with current national

legislation. The room in which the appliance is installed

must be ventilated adequately so as to provide as much

air as is needed by the normal gas combustion process

(the flow of air must not be lower than 2 m

/h per kW of

installed power).

The air inlets, protected by grilles, should have a duct

with an inner cross section of at least 100 cm

and should

be positioned so that they are not liable to even partial

obstruction (see  gure A).

These inlets should be enlarged by 100% - with a

minimum of 200 cm

- whenever the surface of the hob

is not equipped with a flame failure safety device. When

the flow of air is provided in an indirect manner from

adjacent rooms (see  gure B), provided that these are

not communal parts of a building, areas with increased

fire hazards or bedrooms, the inlets should be fitted with

a ventilation duct leading outside as described above.

Adjacent room Room requiring ventilation

A B

Ventilation opening Increase in the gap

between

for comburent air the door and the

flooring

Disposing of combustion fumes

The disposal of combustion fumes should be guaranteed

using a hood connected to a safe and efficient natural

suction chimney, or using an electric fan that begins

to operate automatically every time the appliance is

switched on (see  gure).

Fumes channelled Fumes channelled through

Installation

After prolonged use of the appliance, it is advisable to

open a window or increase the speed of any fans used.

straight outside a chimney or a branched

flue system (reserved for

cooking appliances)

The liquefied petroleum gases are heavier than air and

collect by the floor, therefore all rooms containing LPG

cylinders must have openings leading outside so that

any leaked gas can escape easily.

LPG cylinders, therefore, whether partially or completely

full, must not be installed or stored in rooms or storage

areas that are below ground level (cellars, etc.). Only

the cylinder being used should be stored in the room;

this should also be kept well away from sources of

heat (ovens, chimneys, stoves) that may cause the

temperature of the cylinder to rise above 50°C.

Positioning and levelling

It is possible to install the appliance alongside

cupboards whose height does not exceed that of the

hob surface.

Make sure that the wall in contact with the back of the

appliance is made from a non-flammable, heat-resistant

material (T 90°C).

To install the appliance correctly:

• Place it in the kitchen, the dining room or the bed-sit

(not in the bathroom).

• If the top of the hob is higher than the cupboards, the

appliance must be installed at least 600 mm away from

them.

• If the cooker is installed underneath a wall cabinet,

there must be a minimum distance of 420 mm between

this cabinet and the top of the hob.

This distance should be increased to 700 mm if the wall

cabinets are flammable (see  gure).

• Do not position blinds

behind the cooker or less

than 200 mm away from

its sides.

• Any hoods must be

installed according to

the instructions listed in

the relevant operating

manual.

Levelling

If it is necessary to level the

appliance, screw the adjustable

feet into the places provided on

each corner of the base of the

cooker (see  gure).

The legs* fit into the slots on the

underside of the base of the

cooker.

Electrical connection

Install a standardised plug corresponding to the load

indicated on the appliance data plate (see Technical data

table).

The appliance must be directly connected to the mains using

an omnipolar circuit-breaker with a minimum contact opening

of 3 mm installed between the appliance and the mains. The

circuit-breaker must be suitable for the charge indicated and

must comply with current electrical regulations (the earthing

wire must not be interrupted by the circuit-breaker). The

supply cable must be positioned so that it does not come

into contact with temperatures higher than 50°C at any point.

Before connecting the appliance to the power supply,

make sure that:

• The appliance is earthed and the plug is compliant with

the law.

• The socket can withstand the maximum power of the

appliance, which is indicated by the data plate.

• The voltage is in the range between the values

indicated on the data plate.

• The socket is compatible with the plug of the appliance.

If the socket is incompatible with the plug, ask

an authorised technician to replace it. Do not use

extension cords or multiple sockets.

HOOD

420

Min.

min.

650

mm. with hood

min.

700

mm. without hood

mm.

600

Min. mm.

420

Min. mm.

Once the appliance has been installed, the power

supply cable and the electrical socket must be easily

accessible.

The cable must not be bent or compressed.

The cable must be checked regularly and replaced by

authorised technicians only.

The manufacturer declines any liability should these

safety measures not be observed.

Gas connection

Connection to the gas network or to the gas cylinder

may be carried out using a flexible rubber or steel hose,

in accordance with current national legislation and after

making sure that the appliance is suited to the type of gas

with which it will be supplied (see the rating sticker on

the cover: if this is not the case see below). When using

liquid gas from a cylinder, install a pressure regulator

which complies with current national regulations. To

make connection easier, the gas supply may be turned

sideways*: reverse the position of the hose holder with

that of the cap and replace the gasket that is supplied

with the appliance.

Check that the pressure of the gas supply is consistent

with the values indicated in the Table of burner and

nozzle specifications (see below). This will ensure the

safe operation and durability of your appliance while

maintaining efficient energy consumption.

Gas connection using a flexible rubber hose

Make sure that the hose complies with current national

legislation. The internal diameter of the hose must

measure: 8 mm for liquid gas supply; 13 mm for methane

gas supply.

Once the connection has been performed, make sure

that the hose:

• Does not come into contact with any parts that reach

temperatures of over 50°C.

• Is not subject to any pulling or twisting forces and that

it is not kinked or bent.

• Does not come into contact with blades, sharp corners

or moving parts and that it is not compressed.

• Is easy to inspect along its whole length so that its

condition may be checked.

• Is shorter than 1500 mm.

• Fits firmly into place at both ends, where it will be fixed

using clamps that comply with current regulations.

The appliance must not be installed behind

a decorative door in order to avoid overheating

If one or more of these conditions is not fulfilled or if

the cooker must be installed according to the conditions

listed for class 2 - subclass 1 appliances (installed

between two cupboards), the flexible steel hose must

be used instead (see below).

Connecting a flexible jointless stainless steel pipe to

a threaded attachment

Make sure that the hose and gaskets comply with current

national legislation.

To begin using the hose, remove the hose holder on the

appliance (the gas supply inlet on the appliance is a

cylindrical threaded 1/2 gas male attachment).

Perform the connection in such a way that the hose

length does not exceed a maximum of 2 metres, making

sure that the hose is not compressed and does not come

into contact with moving parts.

Checking the tightness of the connection

When the installation process is complete, check the hose

fittings for leaks using a soapy solution. Never use a flame.

Adapting to different types of gas

It is possible to adapt the appliance to a type of gas other

than the default type (this is indicated on the rating label

on the cover).

3. While the burner is alight, quickly change the position

of the knob from minimum to maximum and vice versa

several times, checking that the flame is not extinguished.

The hob burners do not require primary air adjustment.

After adjusting the appliance so it may be used with a

different type of gas, replace the old rating label with a

new one that corresponds to the new type of gas (these

labels are available from Authorised Technical Assistance

Centres).

Should the gas pressure used be different (or vary

slightly) from the recommended pressure, a suitable

pressure regulator must be fitted to the inlet hose in

accordance with current national regulations relating

Adapting the hob

Replacing the nozzles for the hob burners:

1. Remove the hob grids and slide the burners off their

seats.

2. Unscrew the nozzles using a 7 mm socket spanner

(see  gure), and replace them with nozzles suited to the

new type of gas (see Burner and nozzle speci cations table).

3. Replace all the components by following the above

instructions in reverse.

Adjusting the hob burners’ minimum setting:

1. Turn the tap to the minimum position.

2. Remove the knob and adjust

the regulatory screw, which is

positioned inside or next to the

tap pin, until the flame is small

but steady.

! If the appliance is connected to

a liquid gas supply, the regulatory

screw must be fastened as tightly

as possible:

Safety Chain

! In order to prevent accidental tipping of the appliance,

for example by a child climbing onto the oven door, the

supplied safety chain MUST be installed!

The cooker is fitted with a safety chain to be fixed by

means of a screw (not supplied with the cooker) to the

wall behind the appliance, at the same height as the chain

is attached to the appliance.

Choose the screw and the screw anchor according to

the type of material of the wall behind the appliance. If

the head of the screw has a diameter smaller than 9mm,

a washer should be used. Concrete wall requires the

screw of at least 8mm of diameter, and 60mm of length.

Ensure that the chain is fixed to the rear wall of the cooker

and to the wall, as shown in figure, so that after installation

it is tensioned and parallel to the ground level.

Table of burner and nozzle specifications

128

104

S

R

A

ACMK 6123/WHACMK 6123/WHACMK 6123/WH

Start-up and use

Only available in certain models.

Practical advice on using the burners

For the burners to work in the most efficient way possible

and to save on the amount of gas consumed, it is

recommended that only pans that have a lid and a flat

base are used. They should also be suited to the size of

the burner:

To identify the type of burner, please refer to the diagrams

contained in the “Burner and nozzle specifications”.

For models equipped with a reducer grid, the latter must

be used only for the auxiliary burner, when pans with a

diameter of less than 12 cm are used.

Using the oven

The first time you use your appliance, heat the empty

oven with its door closed at its maximum temperature

for at least half an hour. Ensure that the room is well

ventilated before switching the oven off and opening the

oven door. The appliance may emit a slightly unpleasant

odour caused by protective substances used during the

manufacturing process burning away.

Before operating the product, remove all plastic film

from the sides of the appliance.

Never put objects directly on the bottom of the oven; this

will avoid the enamel coating being damaged.

1. Select the desired cooking mode by turning the

SELECTOR knob.

2. Select the recommended temperature for the

cooking mode or the desired temperature by turning the

THERMOSTAT knob.

A list detailing cooking modes and suggested cooking

temperatures can be found in the relevant table (see Oven

cooking advice table).

During cooking it is always possible to:

• Change the cooking mode by turning the SELECTOR

knob.

• Change the temperature by turning the THERMOSTAT

knob.

Burner Cookware Diameter (cm)

Fast (R) 24 - 26

Semi Fast (S) 16 - 20

Auxiliary (A) 10 - 14

Ideal for gentle cooking (e.g: rice, sauces, roasts, fish) with

liquids (water, wine, broth, milk)

Ideal for stewing ( for a long period of time) and thickening.

Creaming pasta,

Ideal for sautéing.

Cooking on a high flame and browning (roast, steaks,

escalopes, fish fillets, fried eggs.)

Ideal for grilling and browning, starting to cook, frying deep

frozen products.

Ideal for rapidly increasing the temperature of food to fast

boiling in the case of water or rapidly heating cooking liquids.

Using the hob

Lighting the burners

For each BURNER knob there is a complete ring

showing the strength of the flame for the relevant

burner.

To light one of the burners on the hob:

1. Bring a flame or gas lighter close to the burner.

2. Press the BURNER knob and turn it in an

anticlockwise direction so that it is pointing to the

maximum flame setting E.

3. Adjust the intensity of the flame to the desired

level by turning the BURNER knob in an

anticlockwise direction. This may be the minimum

setting C, the maximum setting E or any position in

between the two.

If the appliance is fitted with

an electronic lighting

device*(C) (

see figure

press the BURNER knob

and turn it in an

anticlockwise direction,

towards the minimum flame

setting, until the burner is lit. The burner might be

extinguished when the knob is released. If this

occurs, repeat the process, holding the knob down

for a longer period of time.

f the appliance is equipped with a flame failure

safety device (X), press and hold the BURNER knob

for approximately 3-7 seconds to keep the flame

alight and to activate the device.

If the flame is accidentally extinguished, switch off

the burner and wait for at least 1 minute before

attempting to relight it.

If the appliance is equipped with a flame failure

safety device*, press and hold the BURNER knob

for approximately 2-3 seconds to keep the flame

alight and to activate the device.

To switch the burner off, turn the knob until it

reaches the stop position .

• Stop cooking by turning the SELECTOR knob to the

“0” position.

Always place cookware on the rack(s) provided.

THERMOSTAT indicator light

When this is illuminated, the oven is generating heat.

It switches off when the inside of the oven reaches the

selected temperature. At this point the light illuminates

and switches off alternately, indicating that the thermostat

is working and is maintaining the temperature at a

constant level.

Oven light

This is switched on by turning the SELECTOR knob to

any position other than “0”. It remains lit as long as the

oven is operating. By selecting

with the knob, the

light is switched on without any of the heating elements

being activated.

Assisted cooking mode 6th sense

Cooking modes

A temperature value can be set for all cooking modes

between 60°C and Max, except for the following modes

• GRILL (recommended: set only to MAX power level)

• GRATIN (recommended: do not exceed 200°C).

Function Function Function

TRADITIONAL

OVEN

Both the top and bottom heating elements will come on. When using this traditional

cooking mode, it is best to use one cooking rack only. If more than one rack is used, the

heat will be distributed in an uneven manner.

BAKING

The rear heating element and the fan are switched on, thus guaranteeing the

distribution of heat in a delicate and uniform manner throughout the entire oven. This

mode is ideal for baking and cooking temperature sensitive foods (such as cakes that

need to rise) and for the preparation of pastries on 3 shelves simultaneously.

FAST COOKING

The heating elements and the fan come on, guaranteeing the distribution of heat

consistently and uniformly throughout the oven.

Preheating is not necessary for this cooking mode. This

mode is particularly suitable

for cooking pre-packed

food quickly (frozen or pre-cooked). The best results are

achieved using one cooking rack only.

MULTI-

COOKING

All the heating elements (top, bottom and circular) switch on and the fan begins to

operate. Since the heat remains constant throughout the oven, the air cooks and

browns food in a uniform manner. A maximum of two racks may be used at the same

time.

PIZZA

The circular heating elements and the elements at the bottom of the oven are

switched on and the fan is activated. This combination heats the oven rapidly by

producing a considerable amount of heat, particularly from the element at the

bottom. If you use more than one rack at a time, switch the position of the dishes

halfway through the cooking process.

GRILL

The central part of the top heating element is switched on. The high and direct

temperature of the grill is recommended for food that requires a high surface

temperature (veal and beef steaks, fillet steak and entrecôte). This cooking

mode uses a limited amount of energy and is ideal for grilling small dishes. Place the food

in the centre of the rack, as it will not be cooked properly if it is placed in the corners.

GRATIN

The top heating element and the rotisserie (where present) are activated and

the fan begins to operate. This combination of features increases the effectiveness of

the unidirectional thermal radiation provided by the heating elements through

forced circulation of the air throughout the oven. This helps prevent food from burning

on the surface and allows the heat to penetrate right into the food.

DEFROSTING

The fan located on the bottom of the oven makes the air circulate at room temperature

around the food. This is recommended for the defrosting of all types of food, but in

particular for delicate types of food which do not require heat, such as for example: ice

cream cakes, cream or custard desserts, fruit cakes. By using the fan, the defrosting

time is approximately halved. In the case of meat, fish and bread, it is possible to

accelerate the process using the “multi-cooking” mode and setting the temperature to

80° - 100°C

BOTTOM

The lower heating element is activated. This position is recommended for

perfecting the cooking of dishes (in baking trays) which are already cooked on the

surface but require further cooking in the centre, or for desserts with a covering of

fruit or jam, which only require moderate colouring on the surface. It should

be noted that this function does not allow the maximum temperature to be reached

inside the oven (250°C) and it is therefore not recommended that foods are cooked

using only this setting, unless you are baking cakes (which should be baked at a

temperature of 180°C or lower).

BOTTOM

VENTILATED

The bottom heating element and the fan is activated, which allows for the heat

distribution within the whole cavity of the oven. This combination is useful for light

cooking of vegetables and fish

Practical cooking advice

! In the GRILL cooking mode, place the dripping pan in

position 1 to collect cooking residues (fat and/or grease).

GRILL

• Insert the rack in position 3 or 4. Place the food in the

centre of the rack.

• We recommend that the power level is set to maximum.

The top heating element is regulated by a thermostat

and may not always operate constantly.

PIZZA

• Use a light aluminium pizza pan. Place it on the rack

provided.

For a crispy crust, do not use the dripping pan as it

prevents the crust from forming by extending the total

cooking time.

• If the pizza has a lot of toppings, we recommend

adding the mozzarella cheese on top of the pizza

halfway through the cooking process.

WARNING! The oven is provided with

a stop system to extract the racks and

prevent them from coming out of the

oven.(1)

As shown in the drawing, to extract

them completely, simply lift the racks,

holding them on the front part, and

pull (2).

Storage recess below the oven*

Below the oven a recess can be used to contain

cooking pans and cooker accessories. Moreover,

during oven operation, it may be used to keep

food warm.To open the storage is necessary turn it

downwards.

La page charge ...

Whirlpool ACMK 6123/WH Mode d'emploi

Marque: Whirlpool

Modèle: ACMK 6123/WH

Catégorie: Fours

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Whirlpool ACMK 6123/WH User guide

Whirlpool ACMK 6123/WH Mode d'emploi

Whirlpool ACMK 6123/WH Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents