RIDGID RT12000 Cordless Wet and Dry Vacuum Cleaner Le manuel du propriétaire

Part No. SP7054 Printed in Mexico

12 U.S. GALLON / 45 Liter

WET/DRY VAC

ASPIRADORA PARA MOJADO/SECO DE

12 GALONES EE.UU. / 45 Litros

ASPIRATEUR DE LIQUIDES ET

DE POUSSIÈRES DE

45 Litres / 12 GALLONS DES É-U

FOR QUESTIONS OR INFORMATION CONTACT US AT

1-800-4-RIDGID (1-800-474-3443) from the US and Canada

For service parts visit store.ridgid.com/provacs

OWNER’S MANUAL

MANUAL DEL USUARIO

MODE D’EMPLOI

SAVE THIS MANUAL

FOR FUTURE REFERENCE

WARNING:

To reduce the risk of injury,

the user must read and

understand the owner’s

manual before using this

product.

!

GUARDE ESTE MANUAL

PARA REFERENCIA FUTURA

ADVERTENCIA:

Para reducir el riesgo de

lesiones, el usuario debe leer

y comprender el manual del

usuario antes de usar este

producto.

!

CONSERVER CE MANUEL

POUR RÉFÉRENCE FUTURE

AVERTISSEMENT :

Pour réduire les risques de

blessures, l’utilisateur doit lire

et veiller à bien comprendre le

mode d’emploi avant d’utiliser

ce produit.

!

RT12000

D

R

A

I

N

D

R

A

IN

TABLE OF CONTENTS

*****************

ÍNDICE DE CONTENIDO

*****************

TABLE DES MATIÈRES

*****************

• SAFETY INSTRUCTIONS...........2

• INTRODUCTION ..................4

• ASSEMBLY ......................6

• OPERATION .....................9

• STORAGE ......................13

• MAINTENANCE..................14

• REPAIR PARTS .................16

• INSTRUCCIONES DE SEGURIDAD . 17

• INTRODUCCIÓN .................19

• ENSAMBLAJE ..................21

• FUNCIONAMIENTO ..............24

• ALMACENAMIENTO..............28

• MANTENIMIENTO................29

• PIEZAS DE REPUESTO ...........31

• INSTRUCTIONS RELATIVES

À LA SÉCURITÉ .................32

• INTRODUCTION .................34

• ASSEMBLAGE ..................36

• FONCTIONNEMENT ..............39

• RANGEMENT ...................43

• ENTRETIEN.....................44

• PIÈCES DE RECHANGE ..........48

SP7054 RT12000.indb 1 9/5/18 12:04 PM

2

IMPORTANT SAFETY INSTRUCTIONS

Safety is a combination of using common

sense, staying alert, and knowing how your

Wet/Dry Vacuum Cleaner (“Vac”) works.

Safety Signal Words

DANGER: Indicates a hazardous

situation which, if not avoided, will

result in death or serious injury.

WARNING: Indicates a hazardous

situation which, if not avoided, could

result in death or serious injury.

CAUTION: Indicates a hazardous

situation which, if not avoided, could

result in minor or moderate injury.

When using your Vac, always follow basic

safety precautions including the following:

WARNING

- To reduce the risk of fire,

electric shock, or injury:

• Read and understand this manual and

all labels on the Wet/Dry Vac before

operating.

• Use only as described in this manual.

• Do not leave Vac running while

unattended - you may fail to notice

important signs indicating abnormal

operation such as loss of suction, debris/

liquid exiting exhaust, or abnormal

motor noises. Immediately stop using

Vac if you notice these signs.

• Do not leave Vac when plugged in.

Unplug from outlet when not in use and

before servicing.

• Sparks inside the motor can ignite

flammable vapors or dust. To reduce the

risk of fire or explosion, do not use near

combustible liquids, gases, or dusts,

such as gasoline or other fuels, lighter

fluid, cleaners, oil-based paints, natural

gas, coal dust, magnesium dust, grain

dust, aluminum dust, or gun powder.

• Do not vacuum anything that is burning

or smoking, such as cigarettes, matches,

or hot ashes.

• To avoid the risk of self-ignition of drum

debris, empty drum after each use.

Combustible materials, such as rags or

sawdust containing stain or urethane,

can be sources of such overheating.

!

• Do not vacuum drywall dust, cold

fireplace ash, or other fine dusts with

standard filter. These may pass through

the filter and be exhausted back into the

air. Use a fine dust filter instead.

• To reduce the risk of inhaling toxic

vapors, do not vacuum or use near toxic

or hazardous materials.

• To reduce the risk of electric shock,

do not expose to rain or allow liquid to

enter motor compartment. Store indoors.

• This Wet/Dry Vac is not intended for

use by persons (including children) with

reduced physical, sensory, or mental

capabilities, or lack of experience

and knowledge, unless they have

been given supervision or instruction

concerning use of the appliance by a

person responsible for their safety.

• Do not allow to be used as a toy. Close

attention is necessary when used by or

near children.

• Do not use with a torn filter or without

filter installed except when vacuuming

liquids as described in this manual.

Dry debris ingested by the impeller may

damage the motor or be exhausted into

the air.

• Turn off Vac before unplugging.

• To reduce the risk of injury from

accidental starting, unplug power cord

before changing or cleaning filter.

• Do not unplug by pulling on cord.

To unplug, grasp the plug, not the cord.

• Do not use with damaged cord, plug or

other parts. If your Vac is not working

as it should, has missing parts, has

been dropped, damaged, left outdoors,

or dropped into water, call customer

service.

• Do not pull or carry by cord, use cord

as handle, close a door on cord, or pull

cord around sharp edges or corners.

Do not run Vac over cord. Keep cord

away from heated surfaces.

• Do not handle plug, switch, or the Vac

with wet hands.

SP7054 RT12000.indb 2 9/5/18 12:04 PM

3

IMPORTANT SAFETY INSTRUCTIONS

• Use only extension cords that are rated

for outdoor use. Extension cords in poor

condition or too small in wire size can

pose fire and shock hazards. To reduce

the risk of these hazards, be sure the

cord is in good condition and that liquid

does not contact the connection. Do not

use an extension cord with conductors

smaller than 1,3 mm2 (16 AWG).

• This Wet/Dry Vac is double-insulated,

eliminating the need for a separate

grounding system. Use only identical

replacement parts. Read the instructions

for Servicing Double-Insulated Wet/Dry

Vacs before servicing.

• Do not put any object into ventilation

openings. Do not vacuum with any

ventilation openings blocked; keep free

of dust, lint, hair or anything that may

reduce air flow.

• Keep hair, loose clothing, fingers, and

all parts of body away from openings

and moving parts.

• To reduce the risk of falls, use extra

care when cleaning on stairs.

• To reduce the risk of back injury or falls,

do not lift a Vac that is heavy with liquid

or debris. Partially empty by scooping

debris or draining liquid.

• To reduce the risk of personal injury

or damage to Vac, use only RIDGID

recommended accessories.

• When using as a blower:

- Direct air discharge only at work area.

- Do not direct air at bystanders.

- Keep children away when blowing.

- Do not use blower for any job except

blowing dirt and debris.

- Do not use as a sprayer.

• To reduce the risk of eye injury, wear

safety eyewear. The operation of any

utility Vac or blower can result in foreign

objects being blown into the eyes, which

can result in severe eye damage.

Observe the following warnings that

appear on the motor housing of your Vac:

WARNING: To reduce the risk of

electric shock - do not expose to

rain - store indoors.

DOUBLE INSULATED

GROUNDING NOT REQUIRED.

WHEN SERVICING USE ONLY

IDENTICAL REPLACEMENT PARTS.

!

SAVE THIS MANUAL

CAUTION:

• To reduce the risk of hearing damage,

wear ear protectors when using for

extended hours or in a noisy area.

• For dusty operations, wear dust mask.

• Static shocks are common when the

relative humidity of the air is low.

Vacuuming fine debris with your Vac can

deposit static charge on the hose or Vac.

To reduce the frequency of static shocks

in your home or when using this Vac, add

moisture to the air with a humidifier.

!

WARNING:

• For your own safety, read and

understand owner’s manual.

• Do not run unattended.

• Do not pick up hot ashes,

coals, toxic, flammable or other

hazardous materials.

• Do not use around explosive

liquids or vapors.

!

SP7054 RT12000.indb 3 9/5/18 12:04 PM

4

This Wet/Dry Vac is intended for house-

hold use. It may be used for vacuuming

wet or dry media and may be used as a

blower.

Getting to Know Your Wet/Dry Vac

Read this Owner’s Manual to familiarize

yourself with the product features and

to understand the specific usage of your

new Vac.

INTRODUCTION

Professional Locking Hose - Provides

transfer of vacuum or blowing capability

to work site. Provides the means of

attaching Extension Wands and Nozzles.

Locking Hose 48mm (1 7/8”) x 2.4 m (8’) -

Fits 2 1/2” Accessories.

Extension Wands - These Wands can

be connected together and provide

additional length.

Wet Nozzle - Used for wet pickup on

smooth surfaces to pick up liquid and dry

the surface in one stroke.

Utility Nozzle - General purpose Nozzle

for most vacuuming applications.

Car Nozzle - Dry pickup Nozzle for car

interiors and most upholstery cleaning.

Familiarize yourself with the Accessories included with the Vac. Each Accessory may be

used in various ways for vacuuming and blowing debris. Here is a list of the Accessories

and their uses.

D

R

AI

N

D

R

A

IN

Powerhead Assembly

Carry Handle /

Power Cord Wrap

Drain

Caster

Drum Latch

Dust Drum

Vac Inlet

Caster Foot

Storage

ON/OFF Switch

Blower Port

SP7054 RT12000.indb 4 9/5/18 12:04 PM

5

D

R

A

I

N

D

R

A

I

N

A

D

E

B

C

F

G

J

K

L

H

I

M

Unpacking

Carton Contents List

Key Description Qty

A Wet/Dry Vac ...............................1

B Carry Handle ................................1

C Pan Head Screws, #10 x 3/4”

(19 mm) ....................................6

D Hose Storage Clips .....................2

E Caster Foot w/Storage ................. 4

F Casters ........................................4

G* Qwik Lock™ Filter .......................1

H Professional Locking Hose ..........1

I Extension Wands ......................... 2

J Utility Nozzle ................................1

K Wet Nozzle ..................................1

L Car Nozzle ...................................1

M Owner’s Manual ........................... 1

* The Filter comes preassembled.

This Product Requires Assembly.

Check all parts from carton against the

Carton Contents List.

If any parts are damaged or missing, contact

1-800-4-RIDGID (US and Canada) or by

email at [email protected].

INTRODUCTION

Phillips Screwdriver

Tools Required

SP7054 RT12000.indb 5 9/5/18 12:04 PM

6

ASSEMBLY

NOTE: Remove Powerhead Assembly

from Dust Drum prior to assembly of

Casters and Caster Feet.

1. Turn Dust Drum upside down on floor.

2. Place Caster Foot on floor. Insert the

stem of a Caster into socket of Caster

Foot.

3. Push on the Caster until the Caster ball

end snaps fully into the Socket and the

Caster swivel freely. Repeat for other

three Casters and Caster Feet.

4. Place Caster Foot with Caster over

post on bottom of Dust Drum and press

firmly in place, as shown.

5. Repeat for the other three Caster/

Caster Foot assemblies.

6. Turn the Dust Drum upright.

Caster/Caster Foot Assembly Wet/Dry Vac Assembly

Caster

Foot

Caster

Caster Ball

Caster Stem

Caster Foot

Post Hole

Caster Foot

Post

Dust

Drum

2. Press in on the two Latches located

on either side of the Dust Drum until

they snap into place, securing the

Powerhead Assembly to the Dust Drum.

3. To remove the Powerhead Assembly,

pull out on the two Latches and lift

Powerhead Assembly from the Dust

Drum. Do not force the Latches to

rotate more than slightly outside Drum

Flange.

Drum

Latches

(1 on each

side)

Dust Drum

Powerhead

Assembly

Attaching Powerhead Assembly

to Dust Drum

1. Place Powerhead Assembly on top of

Dust Drum with the Extended Lip of the

Lid aligned with the Vac Inlet. Be sure

Powerhead Assembly is fully seated on

the Dust Drum.

Extended

Lip

Vac

Inlet

Dust

Drum

Powerhead

Assembly

SP7054 RT12000.indb 6 9/5/18 12:04 PM

7

ASSEMBLY

Carry Handle

Powerhead

Assembly

#10 x 3/4"

(19 mm) Pan

Head Screws (2)

Extended

Flange

#10 x 3/4"

(19 mm)

Pan Head

Screws (2)

Hose Clips

(1 on each side)

Powerhead

Assembly

Carry Handle Assembly

1. Locate the Carry Handle and the two

(2) #10 x 3/4” (19 mm) Pan Head

Screws in loose parts bag.

2. Position the Carry Handle on top of the

Powerhead Assembly, with the Carry

Handle Extended Flange to the rear of

the Powerhead Assembly, as shown.

3. Insert a #10 x 3/4” (19 mm) Pan Head

Screw through the hole at each end of

the Carry Handle and into the Powerhead

Assembly. Tighten securely.

Hose Storage Clip Assembly

1. Locate the two (2) Hose Clips and

four (4) #10 x 3/4” (19 mm) Pan Head

Screws in the loose parts.

2. Place a Clip into the recess next to one

of the Latches. The Curve of the Clip

should face outward.

3. Insert a #10 x 3/4” (19 mm) Pan Head

Screw into each mounting hole and

tighten securely.

4. Repeat on the other side.

SP7054 RT12000.indb 7 9/5/18 12:04 PM

8

ASSEMBLY

Extension Wand

Release Button

Accessory Nozzle

Ridges

CONNECT:

Locking Accessories

1. To Connect Accessory: Your

RIDGID Wet/Dry Vac includes Locking

Accessories to prevent the Accessories

from falling off when in use. To

connect the Accessories, align the

Nozzle Ridges of the Accessory with

the Release Button of your Extension

Wand. Press to secure the Nozzle to

the Extension Wand.

2. To Disconnect Accessory: Twist

the Nozzle and Extension Wand to

disengage the Nozzle Ridges and pull.

You may also press the Release Button

and pull to disengage.

Accessory Nozzle

Ridges

Extension Wand

Release Button

DISCONNECT:

Inserting the Professional

Locking Hose

1. Locate the end of the Professional

Locking Hose and align it with the Drum

Inlet. Align the Hose Release Button with

the Ridges on the Vac Inlet. Push the

Hose end straight into the Vac Inlet until

the Hose Release Button fully engages

the Inlet Ridges.

2. To remove Hose, rotate the end of the

Professional Locking Hose in

either direction to release the

Hose Latch from the Inlet Ridges.

Press the Hose Release Button and

pull the Hose end straight out of the

Vac Inlet.

Drum

Vac Inlet

Ridges

Professional

Locking Hose

Hose

Release Button

SP7054 RT12000.indb 8 9/5/18 12:04 PM

9

1

Inlet Ridges

Hose Release Button

2INSERT

HOSE

REMOVE

HOSE

Remove Hose:

1. Rotate Hose End in either direction to

disengage Inlet Ridges.

2. Press the Hose Release Button and

pull the Hose End straight out of the

Vac Inlet.

OPERATION

!

WARNING: To reduce the risk of fire, explosion, or damage to Vac:

• Do not leave Vac running while unattended - you may fail to notice important

signs indicating abnormal operation such as loss of suction, debris/liquid

exiting the exhaust, or abnormal motor noises. Immediately stop using Vac

if you notice these signs.

• Do not leave Vac plugged in when not in use.

• Do not continue running when float has cut off suction.

• Sparks inside the motor can ignite airborne flammables. Do not operate

Vac near flammable liquids or in areas with flammable gases, vapors, or

explosive/airborne dust. Flammable liquids, gases, and vapors include:

lighter fluid, solvent-type cleaners, oil-based paints, gasoline, alcohol, and

aerosol sprays. Explosive dusts include: coal, magnesium, aluminum,

grain, and gun powder.

• Do not vacuum up explosive dusts, flammable liquids, or hot ashes.

• Do not leave sawdust or rags with stain or polyurethane residue inside Vac.

Empty drum after picking up these potentially self-heating materials.

WARNING: To reduce the risk of electric shock or injury:

• Do not expose to rain or allow liquid to enter motor compartment.

Store indoors.

• Do not handle plug, switch, or Vac with wet hands.

• Unplug Vac before servicing. If your Vac is not working as it should, has

missing parts, has been dropped, damaged, left outdoors, or dropped into

water, return it to an authorized service center or call customer service.

• When using an extension cord, use only outdoor-rated cords that are in

good condition. Do not allow the connection to come into contact with

liquid.

ASSEMBLY

SP7054 RT12000.indb 9 9/5/18 12:04 PM

10

OPERATION

Vacuuming Dry Materials

1. The Filter must always be correctly

installed to avoid leaks and possible

Vac damage.

2. To maintain peak performance when

vacuuming fine dust, clean the Drum

and Filter regularily.

NOTE: Do not use a wet Filter when

picking up dry material. The Filter will

quickly clog and be difficult to clean.

3. If the Filter is wet, you must allow it to

dry completely or replace it with a dry

Filter before using the Vac to pick up

dry material.

Polarized Plug

To reduce the risk of electric shock, this

Vac has a Polarized Plug (one blade is

wider than the other). This Plug will fit in

a Polarized Outlet only one way. If the

Plug does not fit fully in the Outlet, reverse

the Plug. If it still does not fit, contact a

qualified electrician to install the proper

Outlet. Do not change the Plug in any way.

With Power Cord plugged in, turn the Vac

“ON” by pressing in on the “I” (top) on the

Power Switch. To turn “OFF” press the

“O” (bottom) of the Power Switch. The

symbols used on the Switch Actuator are

international “On & Off” symbols.

ON/OFF

Switch

CAUTION: To reduce the risk of hearing damage, wear ear protectors

when using the Vac/Blower for extended time or in a noisy area.

!

SP7054 RT12000.indb 10 9/5/18 12:04 PM

11

OPERATION

Emptying the Dust Drum

1. Unplug Power Cord from power source.

2. The Vac comes equipped with a Drain

for easy emptying of liquids. Position

the Vac near a suitable drain or

receptacle and remove the Drain Cap.

3. Remove the Powerhead Assembly by

pulling outward at the top of the two

Latches.

4. Lift Powerhead Assembly from the

Dust Drum and set aside.

5. Empty Dust Drum into a proper waste

disposal container.

WARNING: To reduce the risk

of injury from accidental starting,

unplug power cord before emptying

the drum.

D

R

A

I

N

D

R

A

IN

Drain Cap

Dust

Drum

Drum Latches (2)

!

Vacuuming Liquids

1. Vacuuming up small amounts of liquid

(less than 2” (5 cm) collected in Dust

Drum) does not require Filter removal.

2. When larger amounts of liquid are to

be picked up, remove the Filter, but

not the Filter Cage or Float, to prevent

the Filter from becoming saturated with

liquid. If the Filter becomes saturated,

you may see “mist” coming from the

Blowing Port.

3. When the Drum is “full” the Float will

rise and cut off airflow. The motor

sound will rise in pitch and its speed

will increase indicating the Drum is

“full”. Turn OFF the Vac and unplug the

power cord before emptying the Drum.

4. Following use of Vac for wet pick up,

allow Filter to dry completely to avoid

mildew and Filter damage.

WARNING: Do not operate

without filter cage and float in place.

They prevent liquid from entering the

impeller and damaging the motor.

IMPORTANT: To reduce the risk of

damage to the Vac, do not run Motor with

Float in raised position.

!

SP7054 RT12000.indb 11 9/5/18 12:04 PM

WARNING: Always wear safety

eyewear complying with ANSI Z87.1

(or in Canada, CSA Z94.3) before

using as a blower.

CAUTION: Wear a dust mask if

blowing creates dust which might

be inhaled.

WARNING: To reduce the risk

of injury to bystanders, keep them

clear of blowing debris.

12

!

Blowing Feature

Your Vac features a Blower Port. It can

blow sawdust and other debris. Follow the

steps below to use your Vac as a Blower.

1. Locate the Blower Port, at the rear of

the Powerhead of your Wet/Dry Vac.

2. Align the Professional Locking Hose

Release Button end with the Blower

Port Ridges. Push the Hose End

straight into the Blower Port until the

Hose Release Button fully engages the

Blower Port Ridges.

3. (Optional) Attach the Extension Wand

to swivel end of the Hose.

4. Turn the Vac on and you are ready to

use your Vac as a Blower.

Extension

Wand

(Optional)

Swivel End of Hose

Blower

Port

Ridges

Professional

Locking Hose

Hose Release Button

Remove Hose:

1. Rotate Hose End in either direction to

disengage Blower Port Ridges.

2. Press the Hose Release Button and

pull the Hose End straight out of the

Blower Port.

INSERT HOSE

REMOVE HOSE

1

2

Blower

Port

Ridges

Hose Release Button

1

OPERATION

SP7054 RT12000.indb 12 9/5/18 12:04 PM

13

Accessory Storage

1. For storage, slide the Extension Wands

and the Accessories onto Posts of the

Caster Feet.

2. To remove Wands and Accessories,

lightly rotate and pull upward.

ACCESSORY & HOSE STORAGE

Hose Storage

The Professional Locking Hose may be

stored around the Powerhead Assembly

using the two Hose Storage Clips.

Cord &

Plug

Handle/

Cord Wrap

Tabs

Cord Clip

Professional

Locking Hose

Powerhead

Assembly

Hose Storage Clips (2)

Cord Storage

To store the Cord, wrap it around the top

Handle/Cord Wrap beneath the two Tabs.

Secure the Cord using the Cord Clip on

the Plug.

WARNING: Do not put any

object into ventilation openings.

Do not vacuum with any ventilation

openings blocked; keep free of dust,

lint, hair or anything that may reduce

air flow.

CAUTION: Do not operate vacuum

while the hose is still wrapped

around the powerhead assembly in

the storage position.

!

D

R

A

I

N

D

R

A

I

N

Accessory

Storage Post

Caster

Feet (4)

SP7054 RT12000.indb 13 9/5/18 12:04 PM

14

MAINTENANCE

NOTE: The Filter is made of high quality

paper designed to stop small particles of

dust. The Filter can be used for dry pick

up or small amounts of liquid. Handle the

Filter carefully when removing or installing

it. Creases in the Filter Pleats may occur

from installation but will not affect the

performance of the Filter.

NOTE: Failure to properly seat the

bottom Gasket and Integrated Filter Plate

to the Filter Cage could result in debris

bypassing the Filter.

WARNING: To reduce the risk

of injury from accidental starting,

unplug power cord before changing

or cleaning filter.

Filter Removal:

1. Place fingers under the two Filter Tabs.

2. While pressing down with one thumb

on the Qwik Lock™ Stud that protrudes

through the center of the Filter Plate,

lift up on the Tabs until Filter releases.

3. Slide Filter off Filter Cage.

IMPORTANT: To avoid Blower Wheel

and Motor Damage always reinstall Filter

before using Vac for dry pickup.

Filter Installation:

1. Slide the Qwik Lock™ Filter over the

Filter Cage while aligning the Qwik

Lock™ Stud on the Filter Cage with

the center hole in the Qwik Lock™

Integrated Filter Plate.

2. Make sure the Rubber Gasket at the

bottom of the Qwik Lock™ Filter seats

around the base of the Filter Cage.

3. Firmly press the Qwik Lock™ Integrated

Filter Plate down around the Qwik

Lock™ Stud until it snaps into place.

WARNING: Do not operate

without filter cage and float, as they

prevent liquid from entering the

impeller and damaging the motor.

Qwik Lock™

Stud

Rubber

Gasket at

Bottom of

Filter

PUSH

DOWN

PULL

UP

Filter

Tabs (2)

Integrated Filter Plate

with Center Hole

PULL

UP

Filter Cage

Float

Powerhead

Assembly

Your Filter should be cleaned often to

maintain peak Vac performance.

Filter

Removal & Installation of the

Qwik Lock™ Filter

!

SP7054 RT12000.indb 14 9/5/18 12:04 PM

15

MAINTENANCE

Cleaning A Dry Filter

1. Some removal of dry debris can be

accomplished without removing the

Filter from the Vac. Slap your hand on

top of the Lid while the Vac is turned

off.

2. For best cleaning results due to

accumulated dust, clean the Filter in

an open area. Cleaning SHOULD be

done outdoors and not in the living

quarters.

3. After Filter removal from Vac, remove

the dry debris by gently tapping Filter

against the inside wall of your Dust

Drum. The debris will loosen and fall.

4. For thorough cleaning of Dry Filter

with fine dust (no debris), run water

through it as described under “Cleaning

A Wet Filter”.

Cleaning A Wet Filter

After Filter is removed, run water through

the Filter from a hose or spigot. Take care

that water pressure from the hose is not

strong enough to damage Filter.

IMPORTANT: After cleaning, check the

Filter for tears or small holes. Do not use a

Filter with holes or tears in it. Even a small

hole can allow dust to come out of your

Vac. Replace it immediately.

Allow the Filter to dry completely before

reinstalling and storing the Vac or picking

up dry debris.

WARNING: To assure product SAFETY and RELIABILITY, any other

maintenance, repairs and adjustments should be performed by Authorized Service

Centers, always using RIDGID replacement parts.

!

SP7054 RT12000.indb 15 9/5/18 12:04 PM

WARNING

SERVICING OF DOUBLE-INSULATED WET/DRY VAC

In a double-insulated Wet/Dry Vac, two systems of insulation are provided

instead of grounding. No grounding means is provided on a double-insulated

appliance, nor should a means for grounding be added. Servicing a double-

insulated Wet/Dry Vac requires extreme care and knowledge of the system,

and should be done only by qualified service personnel. Replacement

parts for a double-insulated Wet/Dry Vac must be identical to the parts

they replace. Your double-insulated Wet/Dry Vac is marked with the words

“DOUBLE INSULATED” and the symbol (square within a square) may

also be marked on the appliance.

To reduce the risk of injury from electrical shock, unplug power cord before

servicing the electrical parts of the Wet/Dry Vac.

!

12 U.S. Gallon (45 Liter)

Wet/Dry Vac

Model Number RT12000

Electrical Ratings:

120 V 9.0 A 60 Hz

RIDGID parts are available on-line at store.ridgid.com/provacs

Always order by Part Number - Not by Key Number

!

WARNING: To reduce the risk of injury from electrical shock, unplug power

cord before servicing the electrical parts of the Wet/Dry Vac.

!

WARNING: All disassembly and repairs should be performed by qualified

personnel.

REPAIR PARTS

This product has a 90 day Satisfaction Guarantee Policy

as well as a Limited Lifetime Warranty.

For Warranty and Policy details go to

RIDGID.com/VacWarranty or call 1-800-4-RIDGID.

Part No. SP7054 Form No. SP7054 Printed in Mexico 08/18

www.RIDGID.com

SP7054 RT12000.indb 16 9/5/18 12:04 PM

17

INSTRUCCIONES DE SEGURIDAD IMPORTANTES

La seguridad es una combinación de sentido

común, permanecer alerta y saber cómo funciona

la aspiradora para mojado/seco (“la aspiradora”).

Palabras de señal de seguridad

PELIGRO: indica una situación peligrosa que,

si no se evita, causará la muerte o lesiones graves.

ADVERTENCIA: indica una situación peligrosa

que, si no se evita, podría causar la muerte o

lesiones graves.

PRECAUCIÓN: indica una situación peligrosa

que, si no se evita, pudiera causar lesiones leves o

moderadas.

Cuando utilice la aspiradora, siga siempre las

precauciones básicas de seguridad, incluyendo

las siguientes:

ADVERTENCIA

– Para reducir el riesgo de incendio,

sacudidas eléctricas o lesiones:

• Lea y entienda este manual del usuario y

todas las etiquetas que están colocadas en la

aspiradora para mojado/seco antes de utilizarla.

• Utilice la aspiradora únicamente de la manera

que se describe en este manual.

• No deje la aspiradora en marcha mientras esté

desatendida. Usted podría no notar señales

importantes que indiquen un funcionamiento

anormal, tal como pérdida de succión, residuos

o líquido que salen por el escape o ruidos

anormales del motor. Deje de usar la aspiradora

inmediatamente si observa estas señales.

• No abandone la aspiradora cuando esté

enchufada. Desenchúfela del tomacorriente

cuando no la esté utilizando y antes de realizar

servicio de revisión.

• Las chispas que se producen en el interior del

motor pueden incendiar los vapores inflamables

o el polvo. Para reducir el riesgo de incendio o

explosión, no use la aspiradora cerca de líquidos

o gases inflama bles o combustibles, o polvos

explosivos como gasolina u otros combustibles,

líquido encen dedor, limpiadores, pinturas a base

de aceite, gas natural, polvo de carbón, polvo de

magnesio, polvo de aluminio, polvo de granos de

cereal o pólvora.

• No recoja con la aspiradora nada que esté

ardiendo o humeando, como cigarrillos, fósforos

o cenizas calientes.

• Para evitar el riesgo de autoignición de los

residuos contenidos en el tambor, vacíe el

tambor después de cada uso. Los materiales

combustibles tales como los trapos y el

aserrín, especial mente si contienen tinte para

madera o uretano, pueden ser causas de dicho

sobrecalentamiento.

• No recoja con la aspiradora polvo de panel de

yeso, ceniza fría de chimenea u otros polvos finos

con un filtro estándar. Estos materiales pueden

pasar por el filtro y pueden ser expulsados de

vuelta al aire. Utilice un filtro para polvo fino en

lugar de un filtro estándar.

• Para reducir el riesgo de inhalar vapores tóxicos,

no recoja con la aspiradora materiales tóxicos o

peligrosos ni la use cerca de dichos materiales.

• Para reducir el riesgo de descargas eléctricas,

no exponga la aspiradora a la lluvia ni deje que

entren líquidos en el compartimiento del motor.

Guarde la aspiradora en un lugar interior.

• Esta aspiradora mojado/seco no se destina para

utilizarse por personas (incluyendo niños) cuyas

capacidades físicas, sensoriales o mentales sean

diferentes o estén reducidas, o carezcan de

experiencia o conocimiento, a menos que dichas

personas reciban una supervisión o capacitación

para el funcionamiento del aparato por una

persona responsable de su seguridad.

• No permita que la aspiradora se utilice como un

juguete. Se necesita prestar máxima atención

cuando sea utilizada por niños o cerca de éstos.

• No use la aspiradora con un filtro

desgarrado o sin tener el filtro instalado,

excepto cuando recoja con ella líquidos de

la manera que se describe en este manual.

Los residuos secos absorbidos por el impulsor

podrían dañar el motor o ser expulsados de

vuelta al aire.

• Apague la aspiradora antes de desenchufarla.

• Para reducir el riesgo de lesiones debidas a un

arranque accidental, desenchufe el cordón de

energía antes de cambiar o limpiar el filtro.

• No desenchufe la aspiradora tirando del cordón.

Para desenchufarla, agarre el enchufe y no el

cordón.

• No use la aspiradora con el cordón dañado, el

enchu fe dañado u otras piezas dañadas. Si la

aspira dora no funciona como debe, le faltan

piezas, se ha caído, ha sido dañada, se ha dejado

a la intem perie o se ha caído al agua, llame a

servicio al cliente.

• No tire de la aspiradora usando el cordón ni la

lleve por el cordón, ni use el cordón como asa,

ni cierre una puerta sobre el cordón, ni tire del

cordón alre dedor de bordes o esquinas afilados.

No pase la aspiradora en marcha sobre el

cordón. Mantenga el cordón alejado de las

superficies calientes.

• No maneje el enchufe, el interruptor o la

aspiradora con las manos mojadas.

SP7054 RT12000.indb 17 9/5/18 12:04 PM

18

INSTRUCCIONES DE SEGURIDAD IMPORTANTES

• Utilice únicamente cordones de extensión

que tengan capacidad nominal para uso a la

intemperie. Los cordones de extensión que

estén en malas condiciones o tengan un tamaño

de alambre demasiado pequeño pueden crear

peligros de incendio y descargas eléctricas. Para

reducir el riesgo de estos peligros, asegúrese de

que el cordón esté en buenas condiciones y que

el líquido no entre en contacto con la conexión.

No utilice un cordón de extensión que tenga

conductores con un diámetro menor al calibre

1,3 mm2 (16 AWG).

• Esta aspiradora tiene aislamiento doble, lo cual

elimina la necesidad de un sistema independiente

de conexión a tierra. Utilice única mente piezas

de repuesto idénticas. Lea las instruc ciones

de servicio de revisión de las aspiradoras para

mojado/seco con aislamiento doble.

• No ponga ningún objeto en las aberturas de

ventilación. No recoja nada con la aspiradora

cuando cualquiera de las aberturas de ventilación

esté bloqueada; mantenga dichas aberturas

libres de polvo, pelusa, pelo o cualquier cosa

que pueda reducir el flujo de aire.

• Mantenga el pelo, la ropa holgada, los dedos y

todas las partes del cuerpo alejados de las aber-

turas y de las piezas móviles.

• Para reducir el riesgo de caídas, tenga cuidado

adicional al limpiar en escaleras.

• Para reducir el riesgo de lesiones de espalda

o caídas, no levante una aspiradora que pese

mucho debido a que contiene líquido o residuos.

Saque parte del contenido de la aspiradora o

drénela parcialmente.

• Para reducir el riesgo de lesiones corporales

o daños a la aspiradora, utilice únicamente

accesorios recomendados por Ridgid.

• Cuando utilice la aspiradora como soplador:

– Dirija la descarga de aire solamente hacia el

área de trabajo.

– No dirija el aire hacia las personas que estén

presentes.

– Mantenga alejados a los niños durante la

operación de soplado.

– No utilice el soplador para trabajos que no sean

soplar suciedad y residuos.

– No use la aspiradora como rociador.

• Para reducir el riesgo de lesiones en los ojos, use

pro tección ocular de seguridad. La utilización de

cual quier aspiradora utilitaria o soplador utilitario

puede hacer que se soplen objetos extraños

hacia los ojos, lo cual puede causar daños graves

en los ojos.

GUARDE ESTE MANUAL

AISLAMIENTO DOBLE. NO SE REQUIERE

CONEXION A TIERRA.

CUANDO HAGA SERVICIO DE REVISIÓN DE

LA ASPIRADORA, UTILICE ÚNICAMENTE

PIEZAS DE REPUESTO IDÉNTICAS.

Siga las siguientes advertencias que aparecen en la

caja del motor de la aspiradora:

PRECAUCIÓN:

• Para reducir el riesgo de daños a la audición, use

protectores de oídos cuando utilice la aspiradora

durante muchas horas seguidas o cuando la

emplee en un área ruidosa.

• Para operaciones que generan polvo, use una

máscara antipolvo.

• Las descargas de estática son comunes cuando

la humedad relativa del aire es baja. Si recoge

residuos finos con la aspiradora, se puede

depositar carga estática en la manguera o en

la aspiradora. El mejor remedio para reducir la

frecuencia de las descargas de estática en su casa

o cuando use esta aspiradora es añadir humedad

al aire con un humidificador.

ADVERTENCIA: Para reducir el riesgo de

sacudidas eléctricas, no exponga la aspiradora a

la lluvia y almacénela en interiores.

ADVERTENCIA:

• Para su propia seguridad, lea y entienda el

manual del operador.

• No tenga en marcha la aspiradora desatendida.

• No recoja cenizas calientes, carbón caliente,

materiales tóxicos ni inflamables ni otros

materiales peligrosos.

• No use la aspiradora alrededor de líquidos

o vapores explosivos.

SP7054 RT12000.indb 18 9/5/18 12:04 PM

19

Esta aspiradora para mojado/seco está diseñada

solamente para uso doméstico. Se puede utilizar

para recoger materiales mojados o secos y se

puede usar como soplador.

Familiarización con la aspiradora para seco/mojado

Lea este manual del usuario para familiarizarse con

las características del producto y para entender la

utilización específica de su nueva aspiradora.

INTRODUCCIÓN

Manguera con fijación profesional: Proporciona

transferencia de capacidad de aspiración o soplado

al lugar de trabajo. Proporciona los medios para

acoplar los tubos extensores y las boquillas.

Manguera fijable de 48 mm (1-7/8 pulgadas)

x 2,4 m (8 pies): Compatible con accesorios de

2-1/2 pulgadas.

Tubos extensores: Estos tubos pueden conectarse

entre sí y proporcionan longitud adicional para

tener más alcance.

Boquilla para mojado: Se utiliza para recoger

materiales mojados en superficies lisas con el fin

de recoger líquidos y secar la superficie en una

sola pasada.

Boquilla de uso general: Boquilla que se usa en la

mayoría de las aplicaciones de aspiración.

Boquilla para auto: Boquilla para recoger

materiales secos en interiores de auto y en la

mayoría de limpiezas de tapicería.

Familiarícese con los accesorios que se incluyen con la aspiradora. Cada accesorio puede usarse de diver-

sas maneras para aspirar y soplar residuos. A con tinuación hay una lista de los accesorios y de sus usos.

D

R

AI

N

D

R

A

IN

Powerhead Assembly

Carry Handle /

Power Cord Wrap

Drain

Caster

Drum Latch

Dust Drum

Vac Inlet

Caster Foot

Storage

ON/OFF Switch

Blower Port

Área de

almacena miento

en el pie de ruedecilla

Ensamblaje del

cabezal del motor

Interruptor de

ENCENDIDO Y APAGADO

Entrada de la

aspiradora

Asa de transporte /

enrollador del cable

de alimentación

Orificio de soplado

Pestillo del tambor

Ruedecilla

Drenaje

Tambor para polvo

SP7054 RT12000.indb 19 9/5/18 12:04 PM

20

D

R

A

I

N

D

R

A

I

N

A

D

E

B

C

F

G

J

K

L

H

I

M

Desempaquetado

Lista del contenido de la caja de cartón

Clave Descripción Cant.

A Aspiradora para mojado/seco .............. 1

B Asa de transporte .................................. 1

C Tornillos de cabeza troncocónica

#10 x 3/4 de pulg. (19 mm) ................. 6

D Clips de almacenamiento

de la manguera ...................................... 2

E Pie de ruedecilla con área

de almacenamiento ............................... 4

F Ruedecillas ............................................ 4

G* Filtro Qwik Lock™ ................................. 1

H Manguera con fijación profesional ........ 1

I Tubos extensores .................................. 2

J Boquilla de uso general ......................... 1

K Boquilla para mojado ............................ 1

L Boquilla para auto ................................. 1

M Manual del usuario ................................ 1

* El filtro viene preensamblado.

Este producto requiere ensamblaje.

Compruebe todas las piezas de la caja de cartón

frente a la lista del contenido de la caja de cartón.

Si alguna pieza está dañada o falta, con tác tenos

llamando al 1-800-4-RIDGID (EE.UU. y Canadá) o

por correo electrónico en [email protected].

INTRODUCCIÓN

Destornillador Phillips

Herramientas necesarias

SP7054 RT12000.indb 20 9/5/18 12:04 PM

La page est en cours de chargement...

RIDGID RT12000 Cordless Wet and Dry Vacuum Cleaner Le manuel du propriétaire

RIDGID RT12000 Cordless Wet and Dry Vacuum Cleaner Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents