MasterCool LEGEND SERIES™ R1234yf & R134a REFRIGERANT ANALYZER Mode d'emploi

456 Creamery Way, Exton, PA 19341, USA

Phone: +1 610.524.8800 • Fax: +1 610.524.8807 • Email: info@refrigerantid.com

www.refrigerantid.com

ACTIVATE

SOFTWARE UPDATES

BEFORE FIRST TEST

www.refrigerantid.com/activate

Manual Part Number:

5-06-7000-80-0

Manual File:

012476 Rev. A

Page II

Manual Part Number:

5-06-7000-80-0

Manual File:

012476 Rev. A

Page III

LEGEND ID



Model RI-2018 Series AUTOMOTIVE

REFRIGERANT ANALYZER

OPERATION MANUAL

Manual Part Number:

5-06-7000-80-0

Manual File:

012476 Rev. A

Page IV

Table of Contents

TABLE OF CONTENTS IV

FOR YOUR SAFETY/ANALYZER WARNINGS V

GENERAL CAUTIONS VI

WELCOME VII

1 INTRODUCTION AND OVERVIEW 1-08

1 GENERAL 1-08

1.1 FEATURES 1-09

1.2 Legend ID™ COMPONENTS 1-10

Legend ID™ Base Unit 1-10

Legend R-1234yf Sample Hose 1-10

Legend R-134a Sample Hose 1-11

Legend Sample Hose Extensions 1-11

R-1234yf and R-134a Low Side Couplers 1-11

USB Cord 1-12

R-1234yf and R-134a Tank Adapter Fittings 1-12

AC Power Adapter 1-13

Control Panel 1-13

Back Panel Connections 1-14

Hard Shell Storage/Carrying Case 1-14

2 LEGEND ID

TM

OPERATION 2-15

2.1 FIRST USE 2-15

2.2 POWER ON THE ANALYZER 2-15

2.3 CALIBRATION 2-16

2.4 TESTING THE REFRIGERANT 2-17

2.5 VIEWING THE TEST RESULTS 2-17

2.6 UNDERSTANDING THE TEST RESULTS 2-18

3 MAINTENANCE & TROUBLESHOOTING 3-20

3.1 REPLACING THE SAMPLE HOSE ASSEMBLY 3-20

3.2 INFORMATION SCREENS 3-20

3.3 SOFTWARE UPDATES 3-21

3.4 SETTINGS 3-21

3.5 ERROR MESSAGES 3-22

APPENDICES 4-23

4.1 SPARE PARTS LIST 4-23

4.2 SPECIFICATIONS 4-23

4.3 WARRANTY 4-24

Manual Part Number:

5-06-7000-80-0

Manual File:

012476 Rev. A

Page V

For Your Safety:

PLEASE READ THIS MANUAL IN ITS ENTIRETY BEFORE ATTEMPTING

INSTALLATION OR OPERATION! Attempting to operate this tool without fully

understanding its features and functions may result in unsafe conditions.

Analyzer Warnings

o REFRIGERANT BLEND WARNING: Operate this unit with vehicles or

cylinders marked to contain R-1234yf, R-134a or R-12 refrigerant. Cross-

contamination with other refrigerant types causes severe damage to the

A/C system, to service tools, and equipment. Do NOT attempt to adapt the

unit for another refrigerant. Do NOT mix refrigerant types in a system or in

the same container.

o SAMPLE HOSE WARNING: Replace the sample hose AS SOON AS

LIQUID, OIL OR RED SPOTS (DISCOLORATION) BEGIN TO APPEAR

ON THE INSIDE DIAMETER OF THE SAMPLE HOSE OR WHITE FILTER

ELEMENT. Failure to properly maintain and replace the sample hose will

result in severe damage or inaccurate results.

o FLAMMABILITY WARNING: Some vehicles may contain flammable

refrigerants such as hydrocarbons. R-1234yf is considered a flammable

substance. Failure to follow the manual can result in serious injury or

death. Less than 2 grams of refrigerant are vented with each sample. This

analyzer is designed with sealed heat sources and without sparking

components.

o SAMPLE INPUT WARNING: DO NOT attempt to introduce liquid or

samples heavily laden with oil into the Low Side sampling hose

configuration. Damage caused to the instrument due to the use of the

wrong hose configuration on the wrong port will void the warranty!

o BATTERY CHARGING WARNING: When charging the internal battery with

the supplied power supply, the power supply may become warm. If the

power supply becomes warm, unplug the cord immediately! When

charging multiple analyzers, allow the charger to cool between each

battery.

o AIR SENSOR WARNING: The air detection sensor is a chemical fuel cell

sensor that will eventually expire. The user must return the unit to an

approved vendor in order to replace the air detection sensor whenever the

instrument indicates as such. Failure to replace the air detection sensor will

result in non-functionality of the instrument.

o

POWER SOURCE WARNING: Connection to power sources greater than

13VDC could cause “out of warranty” damage.

o OPPERATIONAL WARNING: If the equipment is used in a manner not

specified by the manufacturer, the protection by the equipment may be

impaired.

Manual Part Number:

5-06-7000-80-0

Manual File:

012476 Rev. A

Page VI

General Cautions

 ALWAYS wear eye and skin protection when working with refrigerants.

Escaping refrigerant vapors will present a freezing danger. Do NOT direct

refrigerant escaping from the sample hose toward exposed skin or toward

the face.

 ALWAYS turn the compressor or automobile engine OFF before connecting

the instrument to an air conditioning system.

ALWAYS inspect the sample hose before each use. Replace the hose if it appears

cracked, frayed, obstructed or fouled with oil.

 DO NOT direct refrigerant vapors venting from hoses towards the skin.

 DO NOT disassemble the instrument. There are no serviceable components

internal to the instrument and disassembly will void the warranty.

 ALWAYS place the analyzer on a flat and sturdy surface.

 To reduce the risk of electrical shock, do NOT disassemble the instrument;

do not use the instrument in wet or damp areas.

 Some systems may contain hydrocarbons or flammable refrigerants. This

analyzer is designed with sealed heat sources and without sparking

components. Ensure adequate ventilation and always take proper

precautions when working with refrigerants.

DO NOT breathe refrigerant and lubricant vapor or mist. Exposure may irritate eyes,

nose, and throat. Use recycling equipment certified to meet the requirements of SAE

J2788, J2843, J3030 or J2851 to remove refrigerant from the A/C system. If accidental

system discharge occurs, immediately ventilate the work area. There must be

adequate ventilation in the vehicle servicing area.

 DO NOT utilize any hose(s) other than those supplied with the instrument.

The use of other hose types will introduce errors into the refrigerant analysis

and instrument calibration.

 ALWAYS verify that the refrigerant, tested from the Low Side, does not

contain or will not emit heavy loads of oil or liquid.

 NEVER admit any sample into the instrument at pressures in excess of 500

psig.

 NEVER obstruct the air intake, sample exhaust or case vent ports of the

instrument during use.

 DO NOT utilize the coupler supplied on the service end of the R-134a or R-

1234yf Sample Hoses for any application other than with the instrument. The

coupler supplied is a modified version that does not contain a check valve

and is not suitable for any other refrigerant application.

Manual Part Number:

5-06-7000-80-0

Manual File:

012476 Rev. A

Page VII

WELCOME

Thank you for purchasing the LEGEND ID

TM

Refrigerant Analyzer.

The Legend ID™ Refrigerant Analyzer is designed for use independently or in conjunction with an

SAE J2843 or J3030 approved A/C Service Machine to determine the purity of gaseous R-134a or R-

1234yf refrigerant. We recommend that all personnel who use this instrument read this manual to

become more familiar with its proper operation.

For further information regarding the application, operation or spare parts, please contact the

Neutronics Inc. Customer Service Department. If you have questions or comments, we would like to

hear from you.

Neutronics Inc.

456 Creamery Way

Exton, PA 19341, USA

Tel: +1 610.524.8800

Fax: +1 610.524.8807

Contact us: [email protected]

Visit us: www.refrigerantid.com

This work is protected under Title 17 of the US Code and is the sole property of Neutronics Inc. No part of this

document may be copied or otherwise reproduced, or stored in any electronic information retrieval system, except as

specifically permitted under US copyright law, without the prior written consent of Neutronics Inc.

Manual Part Number:

5-06-7000-80-0

Manual File:

012476 Rev. A

Page 1-8

1 INTRODUCTION AND OVERVIEW

General

Contamination of refrigerants either in storage cylinders or vehicle air conditioning systems can lead

to component corrosion, elevated head pressures and system failures when utilized by unsuspecting

technicians. The ability of the technician to determine refrigerant type and purity is severely

hampered by the presence of air when attempting to utilize temperature-pressure relations. The

development of various substitute refrigerants further complicates the ability of a technician to identify

refrigerant purity based upon temperature-pressure relationships.

The Neutronics Legend ID™ Refrigerant Analyzer will provide a fast, easy and accurate means to

determine refrigerant purity in refrigerant storage cylinders or directly in vehicle air conditioning

systems. The instrument utilizes non-dispersive infrared (NDIR) technology to determine the weight

concentration of R-1234yf or R-134a refrigerant. Acceptable refrigerant purity as it relates to this

instrument, has been defined by the SAE as a refrigerant mixture that contains 98.0%, or greater of

R-1234yf or R-134a, by weight.

The instrument is supplied complete with an R-1234yf sample hose, an R-134a sample hose (R-12

coupler sold separately), a 100- 240 VAC power transformer, built in Lithium battery, thermal printer,

and all required plumbing housed within a rugged, portable, storage case.

Sample gas is admitted into the instrument through the supplied sample hose and presented to the

sensing device. The instrument provides the user with a digital display of refrigerant purity. The

instrument only considers the weights of the refrigerant and contaminates in the total mixture. Air is

measured, and displayed, separately. Other contents such as refrigerant oil and dye are not

considered contaminants.

The instrument interfaces with the user via a full color graphic LCD, audio indications and soft key

command buttons. Alarm indications are provided to alert of instrument fault conditions or

contaminated refrigerant presence.

Required SAE Statement (SAE J2912): "If the refrigerant being tested is identified as

contaminated (i.e., less than 98% pure R-1234yf or HFC-134a), any visual percentages displayed

of HFC-134a (R-134a) and/or HFO-1234yf (R-1234yf), outside the design certified value is

informational and may not be accurate"

Manual Part Number:

5-06-7000-80-0

Manual File:

012476 Rev. A

Page 1-9

1.1 Features

The Legend ID™ Refrigerant Analyzer is the most precise handheld instrument ever manufactured

for determining the purity of R-1234yf, R-134a and R-12 in the automotive market.

Features Include:

 Quickly and accurately determines refrigerant purity

 Advanced ergonomic design

 Displays % purity:

o R-1234yf

o R-134a

o R-12

 Displays %:

o R-22

o Unknown Refrigerant

o Hydrocarbons

 Displays AIR % independent of the refrigerant sampled

 Capable of analyzing R-12 (1/4” Flare coupler sold separately)

 Multiple Languages:

o English, German, Spanish, French, Italian, Portuguese, Chinese, Japanese,

Korean and Russian

 Easily prints test results with built-in printer (optional)

 Uses Standard 2.25” (57 mm) thermal paper

 Bluetooth compatible (optional)

 Improved oil resistance with user replaceable hose assembly

 Fender friendly resting surface

 Full Color Graphic LCD with on-screen instructions

 Ultra-fast 70 second test time

 Internal, rechargeable Lithium battery for cordless operation in any location

 USB Port for connection to the AC Service Machine & remote software updates

 All accessories stored in hard shell carry/storage case

Manual Part Number:

5-06-7000-80-0

Manual File:

012476 Rev. A

Page 1-10

Analyzer End

Service End

R-1234yf Low Side

Coupler

1.2 Legend ID

TM

Components

Legend ID

TM

Base Unit

The Legend ID™ base unit houses the Full Color Graphic LCD, Infrared Bench, Electrical

Connections, and Rechargeable Battery. These components require no maintenance, therefore

there are no serviceable components internal to the instrument, and disassembly will void

the warranty.

Legend R-1234yf Sample Hose

The 6.5-foot (2 meter) R-1234yf Sample Hose is constructed of polyurethane ether. The hose is

provided with an instrument inlet port mating connector on one end and a brass flow restrictor on

the other end. The brass flow restrictor screws into the R-1234yf Low Side Coupler. The sample

hose is considered a consumable maintenance part. A spare R-1234yf Sample Hose is also

provided.

Control Panel

Manual Part Number:

5-06-7000-80-0

Manual File:

012476 Rev. A

Page 1-11

Legend R-134a Sample Hose

The 6.5-foot (2 meter) R-134a Sample Hose is constructed of polyurethane ether. The hose is

provided with an instrument inlet port mating connector on one end and a brass flow restrictor on

the other end. The brass flow restrictor screws into the R-134a Low Side Coupler. The sample

hose is considered a consumable maintenance part. A spare R-134a Sample Hose is also

provided.

Sample Hose Extensions

The sample hose extensions allow the user to easily connect and disconnect the hose assembly to

the analyzer. The extension is connected directly to the analyzer and the sample hose connects to

the male feral on the opposite end.

R-1234yf Low Side Coupler

The R-1234yf low side coupler is designed with a quick connect adapter to quickly connect the

hose assembly to the Low Side Schrader valve on a R-1234yf vehicle.

R-1234yf (engraved in fine text)

R-134a Low Side Coupler

The R-134a low side coupler is designed with a quick connect adapter to quickly connect the hose

assembly to the Low Side Schrader valve on a R-134a vehicle.

R-134a (engraved in fine text)

Analyzer End

Service End

R-134a Low Side Coupler

Manual Part Number:

5-06-7000-80-0

Manual File:

012476 Rev. A

Page 1-12

USB Cord

The USB Cord is provided to connect the refrigerant analyzer with an SAE J2843 or J3030

approved A/C Service Machine. If connecting to an approved A/C service machine follow the

instructions on this machine to operate the refrigerant analyzer.

R-1234yf Tank Adapter Fitting

The R-1234yf Tank Adapter Fitting will provide the user with an adapter to allow connection of the

R-1234yf Sample Hose to the ½” LH Acme threads on the R-1234yf cylinder.

R-134a Tank Adapter Fitting

The R-134a Tank Adapter Fitting will provide the user with an adapter to allow connection of the

R-134a Sample Hose and Low Side Coupler to a R-134a cylinder ACME port.

R-134a Low Side Stub

(Fits into R-134a Low-Side Coupler)

½” RH Acme Thread

(Threads onto Cylinder Stub)

O-Ring Seal

(Internal)

Manual Part Number:

5-06-7000-80-0

Manual File:

012476 Rev. A

Page 1-13

AC Power Adapter

The Legend ID™ is powered via a Lithium Ion battery. You can also power the unit with the AC

Power Adapter which converts a standard 100-240VAC 50/60Hz wall outlet to 12VDC, 1.6A. This

AC Power Adapter will also charge the battery when connected to the analyzer.

NOTE: Use of any other power source may cause damage to the unit and

void the warranty.

Control Panel

The Control Panel serves as the main user interface. The Control Panel features three soft key

buttons. The current function for each button is displayed above the Soft Key Buttons on the full

color graphic LCD. A Home button and a Power button are also found at the top of the control

panel.

Home

Power

On/Of

f

Soft Keys

Buttons

Graphic

LCD

Green LED

Manual Part Number:

5-06-7000-80-0

Manual File:

012476 Rev. A

Page 1-14

Back Panel Connections

The connections located on the back panel are illustrated below.

CAUTION:

The sample outlet port should never be obstructed. Keep the sample outlet port

free and clear at all times. Do not operate near open flame.

Hard-Shell Storage/Carrying Case

The hard-shell storage/carrying case is custom fit to the Legend ID™. It provides rugged

protection for the instrument, as well as convenient storage for all components. The enclosure is

general purpose and is not watertight.

Sample Inlet

Sample Outlet

Factory

power port

USB Port

Manual Part Number:

5-06-7000-80-0

Manual File:

012476 Rev. A

Page 2-15

2 LEGEND ID

TM

OPERATION

2.1 First Use

The Legend ID™ has a built in Lithium Ion battery. Prior to first use charge the battery for

a minimum of 2 hours with the included AC Power Supply. The analyzer will function and

charge the battery when the AC Power Supply is connected.

2.2 Power On the Analyzer

For use with an SAE J2843 or J3030 certified AC Service Machine, connect one end of the

provided USB cable to the USB port on the back of the analyzer and connect the other end

of the USB cable to the AC Service Machine.

NOTE:

If the unit is used as an independent device the USB cable should not be

connected.

Press the upper right, ‘POWER’ button and the splash screen shown in (Figure 1) will appear.

Press ‘Next’ and the device will warm up as shown in (Figure 2). Warm up will take

approximately 30 seconds.

Figure 1

Figure 2

Manual Part Number:

5-06-7000-80-0

Manual File:

012476 Rev. A

Page 2-16

Once the analyzer warms up, the screen in (Figure 3) will appear offering the option to

change settings or start an analysis. If you wish to adjust factory ‘Settings’, select the left soft

key and refer to section 3 Maintenance & Troubleshooting. To begin an analysis, select

the right ‘Start’ soft key. Next select the type of refrigerant you wish to test (Figure 4).

NOTE:

If you are going to analyze a R-12 vehicle or cylinder you must select R-134a

mode.

2.3 Calibration

Each time the Legend ID™ begins a new test cycle it must complete an air calibration. The

calibration takes 30 seconds and pulls fresh air into the unit via an internal pump. This fresh

air purges any excess refrigerant from the unit and ensures accurate test results. Calibration

REQUIRES a sample hose be connected to the device and disconnected from the vehicle or

refrigerant source.

Once the sample hose is connected to the analyzer, press ‘Start’ to begin an air calibration,

as shown in (Figure 5). This will begin the calibration process and display the screen shown

in (Figure 6).

Figure 3

Figure 6

Figure 5

Figure 4

Manual Part Number:

5-06-7000-80-0

Manual File:

012476 Rev. A

Page 2-17

2.4 Testing the Refrigerant

After the air calibration is complete, the instrument is ready for testing. The analyzer will

direct you to connect the hose to a refrigerant source as shown in (Figure 7). Connect the

hose to the vehicles Low Side Schrader valve, or connect it to the Low Side Port on a

refrigerant cylinder, and open the valve. Allow the refrigerant to flow for a few seconds and

then press the ‘Test’ button to begin the test. The Testing screen shown in (Figure 8) will

display.

2.5 Viewing the Test Results

Upon completion of testing, the Legend ID™ will display (Figure 9). Disconnect the coupler

from the refrigerant source and select ‘Results’ to display the test results (Figure 10). The

percentage displayed for each refrigerant indicates the total purity weight of that

refrigerant, equaling 100%, with air and non-condensable gases measured independently.

Pressing ‘Print’ will print the test results. Pressing ‘Print Prior 5 Results’ will print the last 5

tests completed.

Fi

g

ure 8

Fi

g

ure 9

Fi

g

ure 10

Fi

g

ure 7

Manual Part Number:

5-06-7000-80-0

Manual File:

012476 Rev. A

Page 2-18

If the refrigerant analyzed is 98.0% pure or better, the refrigerant is deemed suitable for

standard recovery and reuse. Should the refrigerant be less than 98.0% pure, the refrigerant

is not suitable for standard recovery and should not be reused. In either case, verify the hose

is disconnected from the refrigerant source and press ‘Exit’ to return to the main screen

(Figure 11).

NOTE:

In R-134a mode, R-12 and R-1234yf are combined into one reading referred to as

“R-12/ R-1234yf.”

2.6 Understanding Test Results

The Legend ID™ is designed to analyze the base gas it is calibrated for. When testing R-

134a vehicle, R-134a should be select as shown on (Figure 12). Conversely when testing a

R-1234yf vehicle, R-1234yf should be selected as shown in (Figure 13). If the wrong base

refrigerant is selected the analyzer will fail the test and produce inaccurate results.

Figure 11

Fi

g

ure 12

Fi

g

ure 13

Manual Part Number:

5-06-7000-80-0

Manual File:

012476 Rev. A

Page 2-19

The refrigerant analyzer is designed to provide visual cues after analysis is complete. When

the refrigerant sampled is found to be 98% pure or greater the analyzer will display a Green

background indicator (Figure 14).

When the sampled refrigerant is found to be between 95% - 98% pure a Yellow background

indicator will appear (Figure 15).

When the sampled refrigerant is found to be less than 95%, presents hydrocarbons or a has

large contamination the screen will illuminate Red and CAUTION SHOULD BE TAKEN

WHEN HANDLING THIS VEHICLE OR CYLINDER (Figure 16).

It is important to note AIR is measured independently of the refrigerant. This means you

could have a percentage of AIR present in a sample or refrigerant that totals or equals 100%

refrigerant. An example of this is present in (Figure 17) below.

If an error message appears at all during or after analysis. Refer to section

3

Maintenance

and Troubleshooting.

Figure 14

Figure 16

Figure 17

Fi

g

ure 15

Manual Part Number:

5-06-7000-80-0

Manual File:

012476 Rev. A

Page 3-20

3 MAINTENANCE & TROUBLESHOOTING

3.1 Replacing the Sample Hose Assembly.

In the event the analyzer displays an Error #3 or Error #5 this may be an indication the

sample hose needs replacing. This will occur when the integrated flow restrictor becomes

clogged with oil, debris or sealant. It can also occur if there is inadequate flow, less than 30

psig (2 Bar) refrigerant in the vehicle or cylinder. Replacement hoses for both the R-134a and

R-1234yf couplers are provided in the kit. Additional replacements are listed on the spare

parts list in section

4

Appendices.

To replace the Sample Hose Assembly, follow the instructions below:

1) Disconnect the sample hose from the refrigerant source and Analyzer

2) Remove the brass restrictor end (with hose attached) from the coupler

and discard. Be sure to use a backing wrench as not to damage the

coupler.

3) Check for signs of oil and debris in the coupler.

4) Use a cleaner which ONLY contains, Tetrachloroethylene and carbon

dioxide, follow safety instructions on the can and spray all parts of the

coupler with the cleaner to remove any oil. DO NOT soak the part for

more than 60 seconds.

5) Allow coupler to dry. Check coupler for oil once again. Failure to clean

the oil out of the coupler will result in premature obstruction of the new

sample hose.

6) Install the brass end of the new sample hose assembly into the

coupler and lightly tighten, usually finger tight is sufficient.

3.2 Information Screens

An

“Information” icon

or ‘Help’ indication will appear at various points throughout the

testing process. This button will provide additional information or tips about the command

screens to help complete your analysis.

La page charge ...

MasterCool LEGEND SERIES™ R1234yf & R134a REFRIGERANT ANALYZER Mode d'emploi

MasterCool LEGEND SERIES™ R1234yf & R134a REFRIGERANT ANALYZER Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents