Thermador PH42GS Manuel utilisateur

INSTALLATION MANUAL

THERMADOR PROFESSIONAL SERIES

®

Wall Hoods

MANUEL D'INSTALLATION

Hottes Murales de la Série PROFESSIONAL

mc

de THERMADOR

MANUAL DE INSTALACIÓN

Para Campanas de Pared PROFESSIONAL

®

de

THERMADOR

Models/

Modèles/

Modelos:

PH30HS

PH36HS

PH48HS

PH36GS

PH42GS

PH48GS

PH54GS

Table of Contents

This THERMADOR

®

appliance is made by

BSH Home Appliances Corporation

1901 Main Street, Suite 600

Irvine, CA 92614

Questions?

1-800-735-4328

www.thermador.com

We look forward to hearing from you!

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Before you Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Installation Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Planning Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Ductwork Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Electrical Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Hood Preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Installation Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Wall Mount Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Duct Covers Assembly & Installation (optional) . . . . . . . . . . . . . . . . . . . . . . . . . 10

Cabinet Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Blower Motor Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Wire Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Grease Trays, Filters and Spacers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Heat Lamp Replacement (some models). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Halogen Light Replacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Customer Support, Accessories & Parts. . . . . . . back page

English 1

Safety

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

APPROVED FOR ALL RESIDENTIAL APPLIANCES

FOR RESIDENTIAL USE ONLY

Before You Begin

IMPORTANT: Save these Instructions for the Local Gas

Inspector’s use.

INSTALLER: Please leave these Instructions with this unit

for the owner.

OWNER: Please retain these instructions for future

reference.

Safety Codes and Standards

This appliance complies with the following Standards:

• UL 507, Standard for the Safety of Electrical Fans

• CAN/CSA-C22.2 No. 113, Fans and Ventilators

It is the responsibility of the owner and installer to

determine if additional requirements and/or standards

apply to specific installations. Always refer to local codes to

ensure all requirements are met.

If required by the National Electrical Code (or Canadian

Electrical Code), this appliance must be installed on a

separate branch circuit.

INSTALLER — show the owner the location of the circuit

breaker or fuse. Mark it for easy reference.

Never modify or alter the construction of the appliance. For

example, do not remove panels or wire covers.

WARNING:

If the information in this manual is not followed exactly,

fire or shock may result causing property damage or

personal injury.

Do not repair or replace any part of the appliance unless

specifically recommended in the manuals. Improper

installation, service or maintenance can cause injury or

property damage or void product warranty. Refer to this

manual for guidance. All other servicing should be done

by a qualified technician.

CAUTION:

The unit is heavy and should be handled

accordingly. Proper safety equipment such

as gloves and adequate manpower of at

least two people must be used in moving the

hood to avoid injury and to avoid damage to

the unit or the floor. Rings, watches, and any

other loose items that may damage the unit

or otherwise might become entangled with

the unit should be removed.

Hidden surfaces may have sharp edges.

Use caution when reaching behind or under

appliance.

WARNING:

Turn off power circuit at service panel and lock out panel

before wiring this appliance. Requirement: 120 VAC, 60

Hz 20 A. Allow the appliance to cool after the power has

been turned off before servicing the appliance.

WARNING:

To reduce the risk of fire use only metal ductwork.

CAUTION:

Vent unit to the outside of building only. This unit is only

designed to be vented outside. It should not be used for

recirculation mode.

English 2

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

Grounding Instructions:

This appliance must be grounded. In the event of an

electrical short circuit, grounding reduces the risk of electric

shock by providing an escape wire for the electric current.

Be sure your appliance is properly installed and grounded

by a qualified technician. Installation, electrical connections

and grounding must comply with all applicable codes.

WARNING – TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK AND INJURY TO PERSONS

OBSERVE THE FOLLOWING:

• This ventilator assembly must be installed with

THERMADOR

®

recommended blowers only. Contact

Customer Service for additional options.

• Use this unit only in the manner intended by the

manufacturer. If you have questions, contact Customer

Service at 1-800-735-4328.

• Before servicing or cleaning unit, switch power OFF at

service panel and lock the service disconnecting

means to prevent power from being switched on

accidentally. When the service disconnecting means

cannot be locked, securely fasten a prominent warning

device, such as a tag, to the service panel.

• Installation work and electrical wiring must be done by

qualified person(s) in accordance with all applicable

codes and standards, including fire-rated construction.

• Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of fuel

burning equipment to prevent back drafting. Follow the

heating equipment manufacturer’s guideline and safety

standards such as those published by the National Fire

Protection Association (NFPA), and the American

Society for Heating, Refrigeration and Air Conditioning

Engineers (ASHRAE), and the local code authorities.

• When cutting or drilling into wall or ceiling, do not

damage electrical wiring and other hidden utilities.

• Ducted fans must always be vented to the outdoors.

• To properly exhaust air, be sure to duct air outside. Do

not vent exhaust air into spaces within walls, ceilings,

attics, crawl spaces or garages.

• Before you plug in an electrical cord, be sure all

controls are in the OFF position.

WARNING:

Improper grounding can result in a risk of electric shock.

Consult a qualified electrician if the grounding

instructions are not completely understood, or if doubt

exists as to whether the appliance is properly grounded.

WARNING:

To Reduce The Risk Of Fire Or Electric Shock

Do not use this fan with any solid-state speed control

devices.

WARNING:

Halogen lights and heat lamps might be hot.

Disconnect from power and allow to cool

before servicing.

WARNING:

Local building codes may require the use of make-up air

systems when using ducted ventilation systems greater

than specified CFM of air movement. The specified CFM

varies from locale to locale. Consult your HVAC

professional for specific requirements in your area.

CAUTION:

For general ventilating use only. DO NOT use to exhaust

hazardous or explosive materials or vapors.

English 3

Installation Preparation

General Information

Before using your appliance, be sure to read this manual.

Pay special attention to the Important Safety Instructions

located at the beginning of the manual.

This manual provides the proper installation instructions for

two styles of THERMADOR PROFESSIONAL

®

series wall

hoods:

• PHxxGS — 27” (686 mm) in depth, with widths of 36”

(914 mm), 42” (1067 mm), 48” (1219 mm), and 54”

(1372 mm). This model series features brushed

stainless-steel canopy with halogen lamps and heat

lamps.

• PHxxHS — 24” (610 mm) in depth, with widths of 30”

(762 mm), 36” (914 mm), and 48” (1219 mm). This

model series features brushed stainless-steel canopy

with halogen lamps.

Planning Information

Figure 1: 24” & 27” Wall Hood Overall Dimensions

18"

(457 mm)

24" & 27"

(610 & 686 mm)

30", 36", 42", 48", 54"

(762, 914, 1067, 1219, 1372 mm)

Parts Included

1 – Metal transition with backdraft

damper

2, 3, or 4 – Stainless steel baffle

filters (depending on model size)

2 – Filter spacers

2 or 3 – Grease trays (depending on

model size)

2 or 4 – Halogen lights (installed)

2 – 175W Heat lamps (on some

models)

1 – Remote blower adaptor

1 – Wooden bracket used as Hood

Mounting Bracket (part of install- DO

NOT THROW AWAY)

1 – Fastener assortment

Use & Care Guide, Installation Manual, and Registration

Card

English 4

Remove all tape and packaging before using

the appliance. Please, recycle the packaging

material, as all THERMADOR

®

appliance

packaging material is recyclable. Never allow

children to play with packaging material.

NOTE:

Do not throw away any packaging until appliance is fully

installed.

Considerations Before Installing Hood

• The installation height ranges from a minimum height

of 30” (762 mm) to a maximum height of 40”

(1,016 mm); however, it is necessary to follow the

cooking appliance manufacturer’s installation

instructions for proper hood height.

• Hood installation height above a rangetop or range can

vary. To obtain the necessary installation height above

a THERMADOR PROFESSIONAL

®

rangetop or range,

consult the appliance's installation manual.

• For indoor grill installations, THERMADOR

®

recommends a minimum of 36" (914 mm) clearance

and remote and inline blowers only.

• Remote blowers require a five wire installation.

• Hood must be vented to the outside of building

only.

Ductwork Preparation

Ducting Recommendations

Proper performance is dependent upon proper ducting.

Local building codes may require the use of make-up air

systems when using ducted ventilation systems greater

than speci¿ed cubic feet per minute (CFM) of air

movement. The speci¿ed CFM varies from locale to locale.

It is the responsibility of the owner and the installer to

determine if additional requirements and/or standards

apply to specific installations.

DO NOT USE FLEXIBLE DUCT; it creates back pressure/

air turbulence and reduces performance. Always use metal

ductwork with a minimum diameter of 6” (150 mm).

Always install a metal vent cover where the ductwork exits

the house.

COLD WEATHER installations should have an additional

backdraft damper installed to minimize backward cold air

flow and a nonmetallic thermal break to minimize

conduction of outside temperatures as part of the ductwork.

The damper should be on the cold air side of the thermal

break. The break should be as close as possible to where

the ducting enters the heated portion of the house.

MAKE-UP AIR: Local building codes may require the use

of make-up air systems when using ducted ventilation

systems greater than specified CFM of air movement. The

specified CFM varies from locale to locale. It is the

responsibility of the owner and the installer to determine if

additional requirements and/or standards apply to specific

installations.

For safety reasons, ducting should vent directly outdoors

(not into an attic, underneath the house, into the garage or

into any enclosed space).

The unit cannot be used in conjunction with a recirculation

unit.

If using a 10" (254 mm) duct, THERMADOR

®

recommends

not exceeding 150 ft (46 m) of duct.

Keep duct runs as short and straight as possible. Elbows

and transitions fittings reduce air flow efficiency. Back to

back elbows and “S” turns give very poor delivery and are

not recommended. A short straight length of duct at the

inlet of a remote blower gives the best delivery.

Hoods are supplied with a 10" (254 mm) round transition. A

locally supplied transition is required for other sizes.

Use Table 1 on page 5 to compute permissible lengths for

duct runs to outdoors.

Tools and Parts Needed

Aluminum tape (DO NOT use duct tape)

1/2” (13 mm) Conduit if required (follow local codes)

1” (25.4 mm) Strain relief

EXTNCB25 – 25 ft. Blower Connector Cable for

distances up to 25 ft.

Ducting as needed

Blower

Flat head and phillips screwdrivers

Drill with 3/16” (4.76 mm) drill bit

3/8” (9.52 mm) nut driver or socket and ratchet

Wire stripper

Protective work gloves

Optional accessories available for separate

purchase. Refer to www.thermador.com for more

details.

Duct Cover

Keep Hot Shelf

Backsplash

English 5

Equivalent Duct Lengths for Commonly Used Transitions

Smooth

Straight

6 1.2

7 0.95

8 0.7

10 0.6

3¼" x 10"

Straight

N/A 1

3¼" x 14"

Straight

N/A 0.7

90° Elbow

Round

612

78

86

45° Elbow

Round

65

74

83

3¼" x 10"

90° Elbow

Round

N/A 5

3¼” x 10"

45° Elbow

Round

N/A 15

3¼" x 10"

Flat Elbow

N/A 20

Round to

3¼" x 10"

61

71

3¼" x 10"

to Round

65

73

Round to

3¼" x 10"

90° Elbow

610

78

3¼" x 10"

to Round

90° Elbow

610

75

3¼" x 10"

Center Reverse

Elbow Left

N/A 15

3¼" x 10"

Center Reverse

Elbow Right

N/A 25

3¼" x 10" Left

Reverse Elbow

N/A 15

3¼" x 10"

Right Reverse

Elbow

N/A 25

Round

Wall Cap

62

72

82

10 2

Round

Roof Cap

62

72

82

2' Long

3¼" x 10"

Flex

N/A 20

3¼" x 10"

to Round

10 1

7" Inline

Backdraft

Damper

7

3¼" x 10"

Roof Jack

and Shutter

N/A

NOTE: These commonly used installation parts can be purchased

at a local hardware store. THERMADOR® does not manufacture all

these parts.

Duct Piece

Size of Duct

Piece (in)

Duct Piece

Size of Duct

Piece (in)

Equivalent

Length (ft)

Equivalent

Length (ft)

Table 1: Duct Lengths

English 6

Electrical Requirements

The unit requires a 120V AC, 60Hz. 15A branch circuit. The

VTR1330E blower in conjunction with a 27" Pro Hood

requires a 20 amp circuit breaker.

The hood should only be connected to a dedicated circuit

(with ground) that has been installed according to relevant

regulations.

When connected to a GFCI-protected supply,

THERMADOR PROFESSIONAL

®

hoods are suitable for

use in damp locations that are protected from outside

weather conditions and not subject to saturation with water

and other liquids, but can be subject to moderate degrees

of moisture (such as an outdoor covered patio or lanai

area). Refer to local codes, NEC/CEC, and or the Authority

Having Jurisdiction (AHJ) for additional information.

Check your local building codes for proper method of

installation. In the U.S., if there are no applicable local

codes, this unit should be installed in accordance with the

National Electric Code ANSI/NFPA No. 70, Current Issue.

In Canada, installation must be in accordance with the CAN

1- B149.1 and .2 - Installation Codes for Gas Burning

Appliances and/or local codes.

The appliance must be grounded. In the event of an

electrical short circuit, grounding reduces the risk of electric

shock by providing a wire that allows the electric current to

escape.

Electrical Data on the Data Rating Plate:

Data, including the model and serial number, is located on

the product data rating plate inside the appliance, visible

after removal of the filter frame (see Figure 26 on page 16).

Hood Preparation

Note:

Optional stainless steel backsplashes are available in

widths to match all pro wall hoods. Before installing the

hood, the backsplash should be installed first. See

directions accompanying the backsplash for full installation

instructions.

Discharge Direction:

The hood can be mounted on a wall or suspended from a

cabinet. Both vertical and horizontal discharge are possible

with either mounting method.

The hood is shipped ready for vertical discharge. To

change to horizontal discharge, move the discharge cover

shown in Figure 2 to the top of the hood. The plate is held

in place by (4) screws.

WARNING:

The appliance must be grounded.

Figure 2: Discharge Direction

This opening

is covered for

horizontal

discharge

This opening

is covered for

vertical

discharge

English 7

Hood Transition

The supplied transition mounts to the top or rear of the

hood depending on the discharge direction.

Assembly of the Transition:

A minimum height clearance of 6” (152 mm) is needed

above the hood for transition mounting. See Figure 1 on

page 3 for overall hood dimensions.

1. Depending on direction of discharge, align mounting

holes at base of transition with the mounting holes of

the ½” (13 mm) flange located at the top or rear of the

hood.

2. Fasten transition to hood using (2) 1” (25.4 mm) sheet

metal screws included with hood.

3. Seal connection between transition and hood with

aluminum tape.

4. Remove tape holding damper closed.

Figure 3: Transition

Figure 4: Transition Cutout Dimensions

10”

(254 mm)

Duct

21¾” (553 mm)

4

5

16

(110 mm)

/

”

1” (25.4 mm)

screw x 2

21¾”

(553 mm)

4¼”

(108 mm)

(43 mm)

11

/

16

”

1

Figure 5: Transition Connection

3

2

1

English 8

Installation Instructions

Wall Mount Installation

Installation Specifications

Figure 6 shows a typical installation of the hood with a duct

cover. Accessory 6” (152 mm) and/or 12” (305 mm) duct

covers are used to fill the space between the hood and

ceiling (available for purchase separately).

The installation height ranges from a minimum height of 30”

(762 mm) to a maximum height of 40” (1016 mm); however,

it is necessary to follow the cooking appliance

manufacturer’s installation instructions for proper hood

height. In Figure 6 one 6" (152 mm) duct cover has been

used in this installation. Add or subtract duct covers as

appropriate to accommodate ceiling height and

recommended hood height.

The duct cover structure is supported by the hood.

NOTICE:

The hood could incur some damage from heat if a

THERMADOR PROFESSIONAL

®

series range or

rangetop is operated with multiple burners at high settings

under a hood that is installed at minimum clearances.

1. After the hood installation height has been determined,

draw a horizontal line at a distance above the cooktop

equal to the recommended hood installation height

plus 15½” (394 mm). This line is the mounting location

of the wooden bracket shipped with the hood.

2. Find the centerline of the hood. Draw a vertical line

along this centerline up to the horizontal line drawn in

Step 1.

3. The hood is mounted to the wall using the wooden

bracket shipped with the hood. Remove the wooden

bracket located at the top side of the hood by removing

the two shipping screws. Mark the center line of the

wood bracket.

4. Locate a stud on both sides of the hood centerline to

use for mounting the wooden bracket as shown in

Figure 7.

5. Align the top of the wood bracket along the horizontal

line drawn in Step 1. Align the centerlines of the

bracket and cooktop.

6. Drill a 3” (76 mm) deep 3/16” (3 mm) tap hole through

the wooden bracket, wall, and into the stud.

7. Use (2) or (3), depending on model, 3” (76 mm) screws

to attach the bracket to the wall, as shown in Figure 7.

For support of longer hoods, use three studs.

Countersink the screw heads to prevent interference

with the hood.

Figure 6: Typical Hood Installation

24” (610 mm)

or 27” (687 mm)

Hood Depth

18”

(457 mm)

24”

(610 mm)

6” Duct

Cover

Hood mounting Heights

Minimum 30” (762 mm)

Maximum 40” (1016 mm)

*Follow cooking

appliance manufacturer’s

recommendations

Figure 7: Mounting the Wooden Bracket

Drywall

To Cooking Surface

Recommended

Hood Height

+

15½” (394 mm)

Cooktop Centerline

Wood

en

Bracke

t

Wall Studs

Screws 2 ea

3” (76 mm)

English 9

8. On the wood bracket, mark the locations used to hang

the hood according to Figure 8.

9. Drill a 3/16” (4.8 mm) tap hole through the wooden

bracket and wall. These 5/8” (16 mm) screws do not

need to go into the studs.

10. Use (2) 5/8” (16 mm) screws to secure the wood

bracket leaving ¼” (6 mm) of each screw exposed for

hanging the hood.

Discharge Direction: Horizontal discharge requires a wall

cutout, as shown in Figure 9, to provide clearance for the

transition. The location of the cutout is determined by the

hood installation height.

Note:

Dashed line indicates cutout needed for clearance of the

transition.

The transition supplied with the hood connects to standard

10-inch round duct. Figure 10 shows the transition

connected for horizontal discharge.

Figure 11 shows the hood configured for vertical discharge.

Installations using this method require a cutout in the

ceiling to accommodate 10" (254 mm) duct and the ½”

(13 mm) conduit carrying power to the unit.

Duct covers, sold separately, are available to cover the

space between the top of the hood and ceiling (see

Figure 14).

Figure 8: Hanging the Hood

Figure 9: Cutout Dimensions

Wooden

Bracket

Screws 2 ea

3” (76 mm)

A

HOOD SIZE A

30” (762 mm) 13” (330 mm)

36” (914 mm) 16” (406 mm)

42” (1067 mm) 19” (483 mm)

48” (1219 mm) 22” (559 mm)

54” (1372 mm) 25” (635 mm)

Dry Wall

12½”

(318 mm)

23” (584 mm)

2¾” (69 mm)

Base of Hood

Location

Cooktop Centerline

Figure 10: Transition Centerline for Horizontal Discharge

Figure 11: Transition Centerline for Vertical Discharge

10¼”

(260 mm)

10½”

(267 m

m)

Transition

Centerline

10¼”

(260 mm)

18”

(457 mm)

Transition

Centerline

W

A

L

5

13

/

16

”

(148 mm)

English 10

11. Remove junction box channel covering the wires.

12. Remove circular knockouts behind junction box

channel.

13. Before hanging hood, install transition per Figure 10 or

Figure 11. Fasten transition with (2) 3/8” sheet metal

screws (supplied) and aluminum tape per all applicable

codes.

Note:

Screws must not hinder damper operation.

14. Using two people to lift, rest the hood on the screws in

the wood bracket. Use the keyholes labeled "F" in

Figure 13. Make sure the wood bracket fits into the

recess on the back of the hood.

15. Tighten the screws in keyholes. Check hood levelness

and adjust if necessary.

16. From inside the hood, drive 5/8” (16 mm) screws

through holes in hood into wooden bracket. See holes

labeled “J” in Figure 13.

17. Connect additional ducting.

Duct Covers Assembly &

Installation

(optional)

Optional duct covers shown in Figure 14 may be used to fill

the space between the hood and ceiling in wall mount

installations. 6" (152 mm) and 12" (305 mm) high duct

covers are available and may be ordered separately (see

page 4)

1. If multiple duct covers are used, connect the pieces

together using sheet metal screws provided with the

duct cover accessories.

2. Attach the duct cover(s) to the hood using sheet metal

screws as shown in Figure 14.

3. From inside of hood, insert 5/8” (16 mm) screws

supplied through the holes indicated on each side and

along the front, into bottom of the cover.

Figure 12: Junction Box Channel

Figure 13: Location of Screw Keyholes

Remove

2 screws

J

F

Figure 14: Attachment of Duct Cover(s) to Hood

Screw quantity

dependent on

hood size.

English 11

Cabinet Installation

The hood can be installed under a cabinet by supporting

the hood from the top.

Note:

The cabinet must be structurally joined to the wall studs to

support the weight of this hood.

Figure 15 shows the (4) screw holes labeled “K” used for

mounting the hood to the bottom of the cabinet. Make sure

both knockouts have been removed.

1. In the base of the cabinet, drill 1/8” (3 mm) tap holes as

indicated in Dimension A in Figure 15 and in Table 2.

2. Screw in (4) 1" (25 mm) screws (provided with hood)

leaving 1/4” (6 mm) exposed to hang hood on.

3. If the hood is installed for vertical discharge, refer to

Figure 16 to create clearance holes for passage of the

transition and conduit. Refer to Dimension B in

Figure 16 and Table 2.

4. For horizontal discharge, use Figure 9 on page 9 for

the geometry of the cutout required for clearance of the

transition.

5. Hang hood from screws and tighten securely.

6. From inside of hood, insert screws supplied. Drill

through holes, use 5/8” (16 mm) screws supplied, (1)

on each side and (4) along the front, into bottom of the

cabinet. See screw holes labeled "L" in Figure 15.

Figure 15: Tap Hole and Screw Hole Locations

A

K

L

23”

(584 mm)

1

9

/16

”

(40 mm)

7

1

/16

”

(179 m

m)

Note:

This figure depicts tap hole and screw hole locations

only. See Figure 1 on page 3 for overall hood

dimensions.

Figure 16: Transition and Conduit Locations

HOOD

SIZE

Tap Holes

A, Figure 15

Conduit Holes

B, Figure 16

30” (762 mm) 29” (736 mm) 13” (330 mm)

36” (914 mm) 35” (889 mm) 16” (406 mm)

42” (1067 mm) 41” (1041 mm) 19” (483 mm)

48” (1219 mm) 47” (1194 mm) 22” (559 mm)

54” (1372 mm) 53” (1346 mm) 25” (635 mm)

Table 2: Centerline Hole Dimensions for Tap and Conduit

Holes

23"

(584 mm)

Wall

B

Cooktop

Centerline

Plan View of Cabinet Cutout

5/8" (16 mm) DIA

clearance holes for

½" (12.7 mm) conduit

to j-box.

2

3

/8

”

(60 mm)

1

7

/8

”

(48 mm

)

1

/8

”

(

29 mm)

3

/16

”

(81 mm)

7

/8

”

(200 mm)

2

3

/8

”

(60mm)

English 12

Blower Motor Installation

All hoods require the choice of a Remote, Inline, or Integral

Blower. Use only THERMADOR

®

blowers with

THERMADOR ventilation hoods. All blower models are

sold separately. See Table 3 Blower & Circuit Breaker

Ratings for recommended blowers. Contact Customer

Service for additional options.

All Hood models are rated for 120 VAC, using a 15 amp or

20 amp circuit breaker.

Blower selection will vary based on the volume of air that

needs to be moved and the length and location of the duct

run. For long duct runs with multiple turns and bends,

consider using a more powerful blower. For the most

efficient air-Àow exhaust, use a straight run or as few

elbows as possible (refer to “Ductwork Preparation” on

page 4).

For indoor grill installations, THERMADOR recommends a

minimum of 36" (914 mm) clearance to the bottom of the

ventilation unit and Remote or Inline blowers only.

Integral Blower Installation Only

1. The blower is attached to the hood using weld studs

provided on the mounting plate. Figure 17 displays the

weld stud locations.

2. Guide the motor mounting plate over the studs.

3. Attach (4) nuts (included with hood) to the weld studs.

Tighten nuts to secure the blower to the hood.

4. Continue to “Wiring the Hood with an Integral Blower”

on page 13.

Blower SKU CFM Voltage (AC)

Blower Current

(AMPS)

Circuit Breaker

(AMPS)

Remote Blower 600 CFM VTR630D 600 120 4.2 15

Remote Blower 1000 CFM VTR1030D 1000 120 5.7 15

Remote Blower 1300 CFM VTR1330E 1300 120 8.5 20* / 15**

Inline Blower 600 CFM VTI610D 600 120 4.2 15

Inline Blower 1000 CFM VTI1010D 1000 120 5.7 15

Integral Blower 600 CFM VTN630C 600 120 2.7 15

Integral Blower 1000 CFM VTN1030C 1000 120 5.4 15

* 20 Amp circuit breaker required when using the VTR1330E Remote Blower with a 27” Pro Wall Hood.

** 15 Amp circuit breaker required when using the VTR1330E Remote Blower with a 24” Pro Wall Hood.

Table 3: Blower & Circuit Breaker Ratings

WARNING:

Cutting the plug of the blower will void the warranty or

eligibility for return or exchange.

CAUTION:

To reduce the risk of fire and electric shock, install this

range hood only with the blowers listed in Table 3.

Figure 17: Weld Stud Locations

English 13

Wiring the Hood with an Integral Blower

Integral Blower models VTN630C and VTN1030C are

integrated into the hood at the time of installation.

For complete installation instructions see the instructions

supplied with the blower unit.

1. Remove junction box channel covering the wires (see

Figure 12 on page 10).

2. Remove circular knockouts (Figure 12 on page 10).

3. Connect the blower’s Molex plug connector to the

connector present inside the hood, as shown in

Figure 19.

4. Install 1” (25.4 mm) conduit connector in junction box.

5. Run black, white, and green wires (#12 AWG) in 1”

(25.4 mm) conduit from the power supply to the

junction box.

6. Connect the power supply wires to the hood wires in

the following order: black to black, white to white, and

green wire to green ground screw on chassis. Use

spring type wire nuts supplied.

• Lost or missing wire nuts should only be replaced

with spring type wire nuts rated for a minimum of

two (2) #18 gauge wires and maximum of four (4)

#14 gauge wires, UL & CSA rated to 600V and

302°F (150°C.)

7. Close the junction box cover.

Wiring the Hood with a Remote Blower

Depending on preference and ducting situation, these

blowers can be mounted on the roof or exterior wall of the

home. An exterior installation may be more appealing to

reduce noise in the kitchen.

For complete installation instructions see the instructions

supplied with the blower unit.

Figure 18: Integral Blower Model VTN1030C

Figure 19: Wiring the Hood with an Integral Blower

2

1/

4

"

(57 mm)

6

7/

8

"

25"

(635 mm)

6

3/

4

"

(171 mm)

8

7/

8 "

(225 mm)

4

1/

8

"

8

1/

4

" (210 mm)

(175 mm)

(105 mm)

From Control Panel

From Blower

Figure 20: VTR1330E Remote Blower

Figure 21: Wiring the Hood with a Remote Blower

19

7/

8

"

(505 mm)

2

1/

8

"

(54 mm)

10 "

(254 mm)

2

1/

8

"

(54 mm)

20

3/

4

"

(527 mm)

12

7/

8

"

(327 mm)

12

1/

8

"

(308 mm)

6

1/

2

"

(165 mm)

1

7/

8

"

(48 mm)

13

5/

8

"

(346 mm)

dia. 9

7/

8

"

(251 mm)

English 14

1. Remove junction box channel covering the wires (see

Figure 12 on page 10).

2. Remove circular knockouts (Figure 12 on page 10).

3. Install 1” (25.4 mm) conduit connectors.

4. Run black, white, and green wires (#12 AWG) in 1”

(25.4 mm) conduit from the power supply to the

junction box.

5. Connect the power supply wires to the hood wires in

the following order: black to black, white to white, and

green wire to green ground screw on chassis. Use

spring type wire nuts supplied.

• Lost or missing wire nuts should only be replaced

with spring type wire nuts, rated for a minimum of

two (2) #18 gauge wires and maximum of four (4)

#14 gauge wires, UL & CSA rated to 600V and

302°F (150°C).

6. Connect the “pigtail” to the connector inside the

junction box.

7. Run five (5) #14 AWG wires in 1” (25.4 mm) conduit

from the remote blower to the second conduit

connector.

8. Connect the remote blower to the pigtail wires as per

Figure 21. Connect the remote blower green (ground)

wire to the ground screw in the junction box. Refer to

the blower installation instructions for further wiring

details.

9. Close the junction box cover.

Wiring the Hood with an Inline Blower

To minimize noise in the kitchen, these blowers are

mounted along the duct line anywhere between the kitchen

and the exterior wall. If there is easy access to duct line (in

an attic, for example), this may be an appealing option.

For complete installation instructions see the instructions

supplied with the blower unit.

1. Remove junction box channel covering the wires (see

Figure 12 on page 10).

2. Remove circular knockouts (Figure 12 on page 10).

3. Install 1” (25.4 mm) conduit connectors.

4. Run black, white, and green wires (#12 AWG) in 1”

(25.4 mm) conduit from power supply to junction box.

5. Connect the power supply wires to the hood wires in

the following order: black to black, white to white, and

green wire to green ground screw on chassis. Use

spring type wire nuts supplied.

• Lost or missing wire nuts should only be replaced

with spring type wire nuts, rated for a minimum of

two (2 #18 gauge wires and maximum of four (4)

#14 gauge wires, UL & CSA rated to 600V and

302°F (150°C).

6. Connect the “pigtail” to the connector inside the

junction box.

7. Run five (5) wires (#14 AWG) in 1” (25.4 mm) conduit

from the inline blower to the second conduit connector.

8. Connect the inline blower to the pigtail wires as per

Figure 23. Connect the inline blower green (ground)

wire to the ground screw in the junction box.

9. Close the junction box cover.

Figure 22: VTI1010D Inline Blower

12

1/

8

"

(308 mm)

14

3/

8

"

(365 mm)

7/

8

" (22 mm)

1

3/

4

"

(44 mm)

19

1/

8

"

(486 mm)

ø9

7/

8

"

(251 mm)

12

"

(305 mm)

12

7/

8

"

(327 mm)

Figure 23: Wiring the Hood with an Inline Blower

English 15

Wire Routing Instruction

Vertical Discharge Wire Routing

Install wire cover per Figure 24. The PH30HS model does

not need a wire cover.

Horizontal Discharge Wire Routing

Install wire cover per Figure 25. The PH30HS model does

not need a wire cover.

Figure 24: Vertical Discharge

Route wires here

Wire Cover

Figure 25: Horizontal Discharge

WARNING:

Turn off electricity at the service panel before wiring the

unit. See Safety Instructions beginning on page 1.

Route wires here

Wire Cover

English 16

Installing Grease Trays, Filters and

Spacers

1. Remove all plastic from hood pieces.

2. Insert in the following order:

1) Grease Tray — Push up and in over the rear lip.

2) Filters —

Slide filter over the front lip. Push filter

rear up, then slide back over rear lip.

Depending

upon the size and model of hood, there will be from

1 to 3 filters per hood.

3) Filter Spacer — Insert these the same way as the

filters.

3. Reverse the above directions to remove the grease

tray, filters and filter spacer (Figure 26).

Note:

Do not use cooktop while hood is disassembled. Grease

trays must be in place before installing the filters.

Heat Lamp Replacement (some models)

• Turn heat lamp clockwise to install (Figure 27).

• Replace lamp with either a PAR-38 175W heat lamp or

a PAR-40 250W heat lamp.

Refer to the Use and Care Guide for additional information.

Halogen Light Replacement

1. Using a flat edge from a screwdriver or equivalent tool,

pry loose the lens cover, as shown in Figure 28.

2. Pull damaged bulb straight out from the socket to

remove.

3. Replace with a new 120 V, 40W (maximum) bulb with

G-9 base. Press pins in bulb base straight into socket

until fully seated. Follow package directions and do not

touch new light with bare hands, the oils from your skin

can reduce the longevity of the bulb.

4. Reinstall the light and cover.

Figure 26: Hood and Parts

Filter

Spacer

Filters

Grease

Tray

1

2

1

Filter

Space

r

Data Rating

Plate

Figure 27: Heat Lamp Replacement

Figure 28: Halogen Light Replacement

Bulb

Lens

Table des matières

Cet appareil électroménager de

THERMADOR

mc

est fait par

BSH Home Appliances Ltd.

6696 Financial Drive, Unit 3

Mississauga, ON L5N 7J6

Des questions?

1-800-735-4328

www.thermador.ca

Nous attendons de vos nouvelles!

Consignes de sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Avant de commencer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Préparation de l'installation . . . . . . . . . . . . . . . . . . . . . . . . . 3

Renseignements généraux . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Renseignements sur la planification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Préparation du conduit d’aération . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Exigences électriques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Préparation de la hotte. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Instructions d’installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Installation murale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Assemblage et installation des recouvrements de conduit (optionnel) . . . . . . . 12

Installation sous une armoire. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Installation du moteur du ventilateur . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Acheminement des câbles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Plateaux à graisse, filtres et pièces d’espacement . . . . . . . . . . . . . . . . . . . . . . 19

Remplacement des lampes infrarouges (certains modèles) . . . . . . . . . . . . . . . 19

Remplacement des lampes halogènes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Service, pièces et accessoires . . . . . . . . . . . . . . page verso

Française 1

Sécurité

CONSIGNES DE SÉCURITÉ IMPORTANTES

LISEZ ET CONSERVEZ CES INSTRUCTIONS

APPROUVÉES POUR UTILISATION RÉSIDENTIELLE

SEULEMENT

Avant de commencer

IMPORTANT : Conservez ces instructions pour

l'inspecteur de la société gazière de votre localité.

INSTALLATEUR : Veuillez laisser ces instructions

d'installation avec l'appareil pour le propriétaire.

PROPRIÉTAIRE : Veuillez conserver ces instructions pour

consultation ultérieure.

Cet appareil est conforme aux normes suivantes :

• UL 507 – norme visant la sécurité en matière de

ventilateurs électriques

• CAN/CSA-C22.2 No 113 – ventilateurs

Il est de la responsabilité du propriétaire et de l’installateur

de déterminer les exigences ou les normes

supplémentaires pouvant s’appliquer à des installations

particulières. Consultez toujours les codes locaux pour

vous assurer du respect de toutes les exigences.

Si le Code national de l’électricité (ou le code canadien de

l’électricité) l’exige, cet appareil doit être installé sur un

circuit de dérivation séparé.

INSTALLATEUR – montrez au propriétaire l’emplacement

du disjoncteur. Marquez-le pour qu’il soit facile à identifier.

Ne modifiez jamais la construction de l’appareil. Par

exemple, n’enlevez pas de panneaux ou de couvre-fils.

AVERTISSEMENT :

Si vous ne suivez pas rigoureusement les

renseignements fournis dans le présent manuel, un

incendie ou une décharge électrique pourrait causer des

dommages matériels ou des blessures corporelles.

Ne réparez et ne remplacez aucune pièce de l’appareil à

moins que le manuel ne recommande expressément de

le faire. L'installation, la réparation ou l'entretien

inadéquat de cet appareil peut causer des blessures

corporelles ou des dommages matériels, ou encore

annuler la garantie du produit. Consultez le présent

manuel pour obtenir des conseils. Tous les autres

travaux d’entretien doivent être effectués par un

technicien qualifié.

ATTENTION :

Cet appareil est lourd et doit être manipulé

en conséquence. Pour éviter tout risque de

blessure ou de dommages à l’appareil ou au

plancher, au moins deux personnes utilisant

de l’équipement adéquat, comme des gants

de protection, et ne portant pas des bagues,

des montres ou tout autre objet semblable

pouvant endommager l’appareil ou s’y

accrocher devraient déplacer l’appareil.

Les surfaces cachées de l’appareil peuvent

comporter des saillies coupantes. Faites

attention lorsque vous prenez l’appareil par

le dessous ou que vous le tirez.

AVERTISSEMENT :

Coupez l’alimentation du disjoncteur et verrouillez le

panneau avant de procéder au câblage de cet appareil.

Exigence : 120 VCA, 60 Hz, 20 A. Avant de procéder à

l’entretien de l’appareil, laissez-lui le temps de refroidir

une fois que l’alimentation électrique est coupée.

AVERTISSEMENT :

Pour réduire les risques d’incendie, n’utilisez que des

conduits métalliques.

ATTENTION :

N’évacuez l’air de cet appareil qu’à l’extérieur de votre

maison. Cet appareil est conçu pour évacuer l’air à

l’extérieur. Il ne doit pas être utilisé avec un mode de

reprise d’air.

La page est en cours de chargement...

Thermador PH42GS Manuel utilisateur

Thermador PH42GS Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents