Vulcan VTEC36 Le manuel du propriétaire

©ITW Food Equipment Group, LLC

3600 North Point Blvd.

Baltimore, MD 21222

RETAIN THIS MANUAL FOR FUTURE USE

FORM F38330 (6-17)

INSTALLATION & OPERATION MANUAL

GAS INFRARED CHARBROILER

MODELS

VTEC14

VTEC25

VTEC36

VTEC48

VTEC60

VTEC36

For additional information on Vulcan or to locate an authorized parts and

service provider in your area, visit our website at www.vulcanequipment.com

- 2 -

IMPORTANT FOR YOUR SAFETY

THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO

INSTALL GAS EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD

START-UP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS

MANUAL.

POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN

THE EVENT THE SMELL OF GAS IS DETECTED. THIS INFORMATION CAN BE

OBTAINED FROM THE LOCAL GAS SUPPLIER.

IMPORTANT

IN THE EVENT A GAS ODOR IS DETECTED, SHUT

DOWN UNITS AT MAIN SHUTOFF VALVE AND

CONTACT THE LOCAL GAS COMPANY OR GAS

SUPPLIER FOR SERVICE.

FOR YOUR SAFETY

DO NOT STORE OR USE GASOLINE OR OTHER

FLAMMABLE VAPORS OR LIQUIDS IN THE VICINITY OF

THIS OR ANY OTHER APPLIANCE.

IN THE EVENT OF A POWER FAILURE, DO NOT

ATTEMPT TO OPERATE THIS DEVICE.

Improper installation,

adjustment, alteration, service or maintenance

can cause property damage, injury, or death.

Read the installation, operating and maintenance

instructions thoroughly before installing or

servicing this equipment.

- 3 -

INSTALLATION, OPERATION AND CARE OF

GAS COUNTERTOP CHARBROILERS

GENERAL

Gas Infrared Charbroilers are designed for commercial use only and feature fast, efficient

gas heat. Each burner is controlled by an adjustable gas valve. Emitter panels are

located directly above each burner to maintain uniform temperature and provide infrared

cooking. The emitter panels will need to be replaced, depending upon your menu and

hours of operation. Emitter panels and stainless steel cooking grids are easily removed

for cleaning when cool. A crumb tray is provided to collect fat run-off and debris; it opens

to the front for inspection or drain-off.

Model

Number of Burners

BTU/hr Input Rating

VTEC14

1

22,000

VTEC25

2

44,000

VTEC36

3

66,000

VTEC48

4

88,000

VTEC60

5

110,000

INSTALLATION

UNPACKING

This charbroiler was inspected before leaving the factory. The carrier assumes full responsibility for the

safe delivery upon acceptance of the shipment. Check for possible shipping damage immediately after

receipt.

If the charbroiler is found to be damaged, complete the following steps:

1. Carrier must be notified within 5 business days of receipt.

2. Carrier’s local terminal must be notified immediately upon discovery (note time, date, and

who was spoken to), and follow up and confirm with written or electronic communication.

3. All original packing materials must be kept for inspection purposes.

4. The charbroiler cannot have been moved, installed, or modified.

5. Notify Vulcan Customer Service immediately at 800-814-2028.

.

Carefully unpack your charbroiler and make sure that no parts are discarded with

packaging material. A pressure regulator designed to operate with the broiler has been

supplied and must be installed before the charbroiler is placed into service (Refer to GAS

PRESSURE REGULATOR INSTALLATION in this manual).

Before installing, verify that the type of gas (natural or propane) and the clearance

dimensions agree with the specifications on the rating plate which is located on the upper

front corner on the right side.

- 4 -

LOCATION

The installation location must be kept free and clear of combustibles. Do not obstruct the

flow of combustion and ventilation air. DO NOT install the charbroiler adjacent to fryers

unless following the provisions detailed by local codes and/or the applicable sections of

ANSI-Z223.1/NFPA #54 (latest edition) and NFPA #96 (latest edition) in the United States

of America or CAN/CSA 149.1 (latest edition) and CAN/CSA149.2 (latest edition) in

Canada.

Sufficient air should be allowed to enter the room to compensate for the amount of air

removed by any ventilating system and for combustion of the gas burners. Do not

obstruct the air flow into and around the appliance. Do not obstruct the flow of flue gases

through and above the broiler's cooking grids. Position the broiler in its final location.

Check that there are sufficient clearances to service the broiler and to make the required

gas supply connection(s). Provide 36" clearance at the front for cleaning, maintenance,

service and proper operation.

This broiler is for use in non-combustible locations only. Installation in combustible

locations is prohibited unless following the provisions detailed by local codes and/or the

applicable sections of ANSI-Z223.1/NFPA #54 (latest edition) and NFPA #96 (latest

edition) in the United States of America or CAN/CSA 149.1 (latest edition) and

CAN/CSA149.2 (latest edition) in Canada and approved by the authority having

jurisdiction.

Minimum clearances to non-combustible walls are 0" to the rear and 0" to the sides.

INSTALLATION CODES AND STANDARDS

The Charbroiler must be installed in accordance with:

In the United States of America:

1. State and local codes.

2. National Fuel Gas Code, ANSI-Z223.1/NFPA #54 (latest edition). This shall include but

not be limited to: NFPA #54 Section 10.3.5.2 for Venting. Copies may be obtained

from The American Gas Association Accredited Standards Committee Z223, @ 400

N. Capital St. NW, Washington, DC 20001 or the Secretary Standards Council, NFPA,

1 Batterymarch Park Quincy, MA 02169-7471

NOTE: In the Commonwealth of Massachusetts

All gas appliances vented through a ventilation hood or exhaust system equipped with

a damper or with a power means of exhaust shall comply with 248 CMR.

3. NFPA Standard # 96 Vapor Removal from Cooking Equipment, latest edition, available

from the National Fire Protection Association, Batterymarch Park, Quincy, MA 02269.

In Canada:

1. Local codes.

2. CAN/CSA-B149.1 Natural Gas Installation (latest edition)

3. CAN/CSA-B149.2 Propane Installation Code (latest edition), available from the

Canadian Gas Association, 178 Rexdale Blvd., Etobicoke, Ontario, Canada M9W 1R3

- 5 -

KEY COMPONENTS

The charbroiler

and its parts are hot. Use care

when operating, cleaning or

servicing the charbroiler.

Cooking Grids – The cooking grids

should always be in place and properly

seated on the emitter panels during

operation. Wash grids thoroughly with

soap and water solution and rinse

before first use.

Crumb tray – The crumb tray is the

removable pan that catches any debris

that falls from the broiling area. The

crumb trays should be pushed all the

way in while the unit is operation.

Emitter Panel – The charbroiler must

never be operated without the emitter

panels in place. The emitter panels

protect the burner from food drippings

and debris. Operating the burner without

the emitter panels in place will cause

poor performance and clogging of the

burner ports. The emitter panels

disperse energy and facilitate infrared

cooking.

The emitter panels should rest on top of

the side burner tabs and inside of the

front and rear burner tabs over each

burner. The emitter panels should be

placed in position with the flanged

edges pointing upwards. See Fig. 2.

Emitter panels are consumable.

The emitter panels will need to be

replaced, depending upon your menu

and hours of operation.

Cooking Grid

Fig. 1

Emitter Panel

Crumb Tray

Burner

Fig. 2

Emitter Panel In Place

Emitter Panel Flanges

Emitter Panel

Side Burner Tabs

Front/Rear Burner Tabs

- 6 -

LEVELING

It is important that the charbroiler is level front to back and left to right. Areas of uneven

heat distribution will occur on an unleveled unit. The charbroiler is equipped with

adjustable legs. Turn the feet at the bottom of the legs to adjust to level. The unit should

be rechecked for level anytime it has been moved.

VENTILATION HOOD

The broiler should be installed under a suitable ventilation hood. For safe operation and

proper ventilation, keep the space between the charbroiler and vent hood free from any

obstructions.

GAS CONNECTION

The data plate on the lower right side of the charbroiler indicates the type of gas your unit

is equipped to burn. DO NOT connect to any other gas type.

All gas supply connections and any pipe joint compound must be resistant to

the action of propane gases.

Purge the supply line to clean out any dust, dirt, or any foreign matter before connecting

the line to the unit.

Codes require that a gas shut-off valve be installed in the gas line ahead of the

charbroiler. The gas supply line must be at least the equivalent of ¾” iron pipe.

A pressure regulator is supplied and must be installed outside of the broiler when making

the gas supply connection. Standard orifices are set for 4"WC (Water Column) for

Natural Gas — 10"WC (Water Column) for Propane. Use the

1

/

8

” pipe tap on the burner

manifold for checking pressure. Make sure the gas piping is clean and free of

obstructions, dirt, and piping compound.

An adequate gas supply is necessary. Undersized or low pressure lines will restrict the

volume of gas required for satisfactory performance. A minimum supply pressure of 7"

W.C. for natural gas and 11" W.C. for propane gas is recommended. With all units

operating simultaneously, the manifold pressure on all units should not show any

appreciable drop.

When testing the gas supply piping system, if test pressures exceed ½ psig (3.45 kPa),

the charbroiler and its individual shutoff valve must be disconnected from the gas supply

piping system. When test pressures are ½ psig (3.45 kPa) or less, the charbroiler must

be isolated from the gas supply piping system by closing its individual manual shut-off

valve during any pressure testing of the system.

- 7 -

Prior to lighting, check all joints in the gas supply line for leaks.

Use soap and water solution. Do not use an open flame.

GAS PRESSURE REGULATOR INSTALLATION

Gas regulator pressure is preset at 4” Water Column (W.C.) for natural gas, and 10” W.C.

for propane gas. Minor adjustments may be required based on site specific gas pressure.

Install the regulator as close to the broiler on the gas supply line as possible. Make sure

that the arrow on the underside of the regulator is oriented in the direction of gas flow to

the broiler (Fig. 3) and the regulator is positioned with the vent plug and adjustment

screw upright (Fig. 4).

Fig. 3

Fig. 4

The minimum supply pressure (upstream of the regulator) should be 7-9” W.C. for natural

gas and 11-12” W.C. for propane gas. At no time should the charbroiler be connected to

supply pressure greater than ½ psig (3.45 kPa) or 14” W.C.

CASTER EQUIPPED CHARBROILERS

Charbroilers mounted on stands with casters must use a flexible connector (not supplied)

that complies with the Standard for Connectors for Movable Gas Appliances, ANSI Z21.69

• CSA 6.16 and a quick-disconnect device that complies with the Standard for Quick-

Disconnect Devices for use With Gas Fuel, ANSI-Z21.41 • CSA 6.9. In addition, adequate

means must be provided to limit movement of the broiler without depending on the

connector and the quick-disconnect device or its associated piping to limit broiler

movement. Attach the restraining device at the rear of the charbroiler. If disconnection of

the restraint is necessary, turn off the gas supply before disconnection. Reconnect the

restraint prior to turning the gas supply on and return the charbroiler to its installation

position.

- 8 -

OPERATION

The charbroiler and its parts are hot. Use care when operating,

cleaning or servicing the charbroiler.

BURNER LIGHTING

The burners should be left on the maximum (MAX) setting for most efficiency when

cooking. The burners may be turned to the minimum (MIN) setting during slow periods to

save energy. See Fig. 6.

The VTEC charbroiler does not have a pilot

and each burner lights directly from a spark

igniter or from an outside ignition source (such

as a lit taper, long handle lighter, etc).

LIGHTING BURNER WITH SPARK IGNITER

1. Turn the main gas shut-off valve and the

individual burner control knobs to the OFF

position (clockwise until stops). Wait 5

minutes.

2. Push and turn the burner control knob to the

MAX setting (counterclockwise to vertical/90°

position) on the burner you intend to light.

(Fig. 5)

3. Immediately, while viewing through the

burner sight hole, turn the igniter knob

clockwise until you hear a click (approx. ¼

turn) and see the spark. The burner should

ignite immediately and flames should be

visible through the burner sight hole.

4. If the burner fails to light immediately,

repeat step 3, two more times. If the burner

has still not ignited at this point, turn the

main gas shut-off valve and all burner

valves to the OFF position (clockwise until

stops) and proceed with manual burner

lighting instructions on following page.

5. Repeat steps 2-4 until all burners are lit.

Turn on one burner control knob at a time

and ensure burner is lit before proceeding

to light the next burner.

Fig. 6

Fig. 5

Burner Sight Hole

Burner Control Knob

Igniter Knob

OFF MAXIMUM MINIMUM

- 9 -

TO COMPLETELY SHUTDOWN THE BURNERS

For complete shutdown: Turn the main gas supply valve OFF. Make sure all individual

burner valves are OFF (turned completely clockwise until stops).

PREHEATING THE CHARBROILER

Allow the charbroiler to preheat for 20 minutes on the maximum (MAX) setting. Rub

grates with cooking oil before using to help reduce sticking.

LIGHTING BURNER MANUALLY

1. Turn the main gas shut-off valve and the

individual burner control knobs to the OFF

position (clockwise until stops). Wait 5

minutes.

2. Apply a flame from an outside ignition source

(such as a lit taper, long handle lighter, etc)

directly to the gap between the bottom of the

emitter panel and the top of the intended

burner box at the front of the unit. See Fig. 7.

3. Push and turn the burner control knob to the

MAX setting (counterclockwise to vertical/90°

position) on the burner you intend to light.

(Fig. 8)

4. View through the burner sight hole (Fig.8) to

ensure the burner has lit.

5. If the burner fails to light within 4 seconds of

applying flame to the directed area, turn the

main gas shut-off valve and all burner

valves to the OFF position (clockwise until

stops). Contact an authorized service

contractor.

6. Repeat steps 2-4 until all burners are lit.

Turn on one burner control knob at a time

and ensure burner is lit before proceeding

to light the next burner.

Burner Sight Hole

Burner Control Knob

Fig. 8

Cutaway View

Fig. 7

Outside Ignition Source

Emitter Panel

Gap

Burner Box

- 10 -

CLEANING

Never leave emitter panels wet after cleaning. Leaving panels wet after

cooking or cleaning may accelerate corrosion process and result in premature failure.

WEEKLY

When cool, remove cooking grids, emitter panels and heat shield. Clean and vacuum any accumulated

debris from inside burner boxes. Clean inside chassis area anywhere fat, grease, or food can

accumulate. Clean heat shield while removed (Fig. 10). Repeat weekly process more often as needed.

The charbroiler and its

parts are hot. Use care when operating,

cleaning or servicing the charbroiler.

Scrape cooking grids during broiling with a

stainless steel scraper or stainless steel wire

brush to keep the grates clean. Do not allow

debris to accumulate on the grates. (Fig. 9)

Top grates may be immersed in cleaning

compound overnight. In the morning, rinse

with hot water to remove any residues of

cleaning compound.

Stainless steel surfaces may be cleaned using

damp cloth with mild detergent and water

solution. Clean heavy, baked on grease and

splatter that do not respond to normal cleaning

by using cleaning solution with a Scotch-

Brite

TM

pad. Rub with the grain of the surface

– do not rub in a circular motion.

DAILY

After cooking, allow unit to run on MAX setting

for 10 minutes before shutting OFF.

This will make cleaning debris from the emitter

panels easier when they cool down.

When cool, remove cooking grids and emitter

panels, clean places where fat, grease, or food

can accumulate. Brush or use scraper to

remove any accumulated debris from emitter

panel surfaces. Be careful to keep inside

burner boxes clear of debris. Remove crumb

tray when cool and empty. (Fig. 10)

Fig. 10

Cooking Grid

Emitter Panel

Crumb Tray

Heat Shield

Inside

Burner Box

Fig. 9

- 11 -

Never cover surface of unit with pans or other objects in attempt to “burn off”

or clean debris from unit. This will cause a buildup of heat that can potentially damage

and warp components of the charbroiler. Do not cover surfaces with aluminum foil as this

may block or disrupt the designed air flow pattern and affect performance.

MAINTENANCE

The charbroiler and its parts are hot. Use care when operating,

cleaning or servicing the charbroiler.

VENT SYSTEM

At least twice a year the exhaust hood (venting system) should be examined and cleaned.

LUBRICATION

All valves, at the first sign of sticking, should be lubricated by a trained technician using

high temperature grease.

EMITTER PANELS

Emitter panels are consumable.

The emitter panels will need to be replaced, depending upon your menu and hours of

operation. Replace emitter panels if warped or holes appear.

SERVICE

Contact your local Service Contractor for any repairs or adjustments needed on this

equipment. For a complete listing of service and parts depots refer to

www.vulcanequipment.com. When calling for service, the following information should be

available from the appliance identification plate: Model Number and Serial Number.

- 12 -

TROUBLE SHOOTING

Uneven heating

A. Burner valves improperly adjusted

B. Fluctuating gas pressure

C. Appliance is not level

D. Emitter panels are not properly seated or damaged

E. Emitter panels are excessively dirty

Too much top heat

A. Faulty hood ventilation

C. Overrated gas pressure

D. Unit is excessively dirty

E. Emitter panels are not properly seated or damaged

Uneven heat side to side

A. Burner valves improperly adjusted

B. Appliance is not level side to side

C. Crumb tray is not pushed all the way in

D. Emitter panels are not properly seated or damaged

E. Emitter panels are excessively dirty

Uneven heat front to back

A. Appliance is not level front to back

B. Faulty hood ventilation

C. Crumb tray is not pushed all the way in

D. Emitter panels are not properly seated or damaged

E. Emitter panels are excessively dirty

F. Designed air flow pattern obstructed

Burner not lighting

A. Check that igniter electrode is sparking when igniter

knob is turned clockwise

B. Check for damaged, loose or dirty igniter wires, igniter

and electrode

C. Burner valve not on MAX setting

D. Gas pressure too low

E. Inside burner box or burner venturi excessively dirty

Burner flames too low

A. Burner valves improperly adjusted

B. Gas pressure too low

C. Inside burner box or burner venturi excessively dirty

D. Clogged burner orifice

Burner flames to high

A. Emitter panels are not properly seated or damaged

B. Gas pressure too high

Fluctuating gas pressure

A. Checked for clogged vent on regulator

- 13 -

ACCESSORY INSTALLATION

The charbroiler and its parts are hot. Use care when operating,

cleaning or servicing the charbroiler.

1

2

- 14 -

4

3

- 14 -

3

4

- 13 -

INSTALLATION DE COMPLICE

Le gril et ses pièces sont chauds. Faites attention lorsque vous

employez, nettoyez ou entretenez ce gril.

1

2

- 12 -

LOCALISATION D'UNE PANNE

Chaleur inégale

A. Boutons des brûleurs mal réglés

B. Variation de la pression du gaz

C. L'appareil n'est pas nivelé

D. Panneaux émetteurs mal placés ou endommagés

E. Les panneaux émetteurs sont excessivement sales

Trop de chaleur sur le dessus

A. Ventilation défectueuse de la hotte

B. La pression du gaz est surestimée

C. L'appareil est excessivement sale

D. Panneaux émetteurs mal placés ou endommagés

Chaleur inégale d’un côté à

l’autre

A. Boutons des brûleurs mal réglés

B. L'appareil n'est pas horizontal d'un côté à l'autre

C. Le ramasse-miettes n'est pas correctement rentré

D. Panneaux émetteurs mal placés ou endommagés

E. Les panneaux émetteurs sont excessivement sales

Chaleur inégale de l’avant

vers l’arrière

A. L'appareil n'est pas horizontal d'avant en arrière

B. Ventilation défectueuse de la hotte

C. Le ramasse-miettes n'est pas correctement rentré

D. Panneaux émetteurs mal placés ou endommagés

E. Les panneaux émetteurs sont excessivement sales

F. Schéma de circulation d'air obstrué

Le brûleur ne s'allume pas

A.Vérifiez que l'électrode de l'inflammateur jette des

étincelles quand le bouton de l'inflammateur est tourné

dans le sens des aiguilles d'une montre

B.Vérifiez que l'électrode de l'inflammateur jette des

étincelles quand le bouton de l'inflammateur est tourné

dans le sens des aiguilles d'une montre. Vérifiez si les

fils d'inflammateur sont sales, relâchés ou endommagés,

contrôlez l'inflammateur et l'électrode

C. Le bouton de brûleur n'est pas réglé sur MAX

D. Pression du gaz trop basse

E. L'intérieur du boîtier de brûleur ou le brûleur est

excessivement sale

Flammes des brûleurs trop

basses

A. Boutons des brûleurs mal réglés

B. Pression du gaz trop basse

C. L'intérieur du boîtier de brûleur ou le brûleur est

excessivement sale

D. Obstruction de l’orifice du brûleur

Flammes des brûleurs trop

hautes

A. Panneaux émetteurs mal placés ou endommagés

B. Pression du gaz trop haute

Variation de la pression du

gaz

A. Contrôlé pour obstruction de la ventilation du régulateur

- 11 -

PAR SEMAINE

Une fois refroidis, retirez les grilles de cuisson, les panneaux émetteurs et la protection anti-chaleur.

Nettoyez et aspirez tout débris accumulé dans les boîtiers des brûleurs. Nettoyez toute accumulation

de gras, graisse ou d'aliment à l'intérieur du châssis. Enlevez la protection anti-chaleur pour la nettoyer

(Fig.10). Répétez ce processus hebdomadaire aussi souvent que nécessaire.

Ne jamais couvrir la surface de l’élément avec une casserole ou autres objets

pour essayer de « brûler » ou de nettoyer les débris de l’élément. Cela provoquera une

augmentation de la chaleur qui peut potentiellement endommager ou déformer les

composants du gril. Ne recouvrez pas les surfaces avec du papier aluminium car cela

pourrait provoquer le blocage ou la perturbation du plan de circulation de l'air et affecter

la performance.

ENTRETIEN

Le gril et ses pièces sont chauds. Faites attention lorsque vous

employez, nettoyez ou entretenez ce gril.

SYSTÈME DE VENTILATION

La hotte à évacuation (système de ventilation) devrait être examinée et nettoyée au

moins deux fois par année.

LUBRIFICATION

Toutes les soupapes devraient être lubrifiées par un technicien qualifié avec une huile

résistant aux températures élevées dès le premier signe de coincement.

PANNEAUX ÉMETTEURS

Les panneaux émetteurs sont des consommables.

En fonction de votre menu et des heures de fonctionnement, les panneaux émetteurs

devront être remplacés.Remplacez les panneaux émetteurs s’ils sont tordus ou s’ils sont

troués.

SERVICE

Communiquez avec votre service à la clientèle local pour toute réparation ou tout réglage

nécessaire sur cet équipement. Pour une liste des bureaux des services et des pièces,

consultez www.vulcanequipment.com.. Lorsque vous appelez pour du service, les

renseignements suivants devraient être disponibles sur la fiche signalétique de

l’appareil : le numéro du modèle et le numéro de série.

AVIS

- 10 -

PRÉCHAUFFAGE DU GRIL

Préchauffez le gril pendant 20 minutes sur réglage maximum (MAX) Frottez les grilles

avec de l'huile de cuisine avant l'utilisation pour réduire la viscosité.

NETTOYAGE

Ne laissez jamais les panneaux émetteurs humides après le nettoyage. Le fait

de laisser les panneaux humides après la cuisson ou le nettoyage peut accélérer le

processus de corrosion et les endommager prématurément.

Le gril et ses pièces

sont chauds. Faites attention lorsque vous

employez, nettoyez ou entretenez ce gril.

Grattez les grilles de cuisson avec un grattoir

en acier inoxydable ou une brosse métallique

en acier inoxydable pour garder les grilles

propres. Empêchez les débris de s'accumuler

sur les grilles. (Fig. 9) Les grilles supérieures

peuvent être immergées dans du détersif

durant la nuit. Au matin, rincez-les avec de

l'eau chaude pour enlever tout résidu du

détersif.

Les surfaces en acier inoxydable peuvent être

nettoyées à l’aide d’un linge humide et d’une

solution d’eau et d’un savon doux. Netoyer la

graisse solidifiée et les éclaboussures qui sont

difficile à nettoyer utilisant une solution de

nettoyage et un tampon Scotch-Brite

MD

Frottez

dans le sens des veines de la surface - ne

frottez pas dans un mouvement circulaire.

QUOTIDIENNEMENT

Après la cuisson, laissez l'appareil tourner sur

MAX pendant 10 minutes avant de

l'ARRÊTER.

Ce qui facilitera le nettoyage des débris

des panneaux émetteurs après

refroidissement.

Une fois refroidis, retirez les grilles de cuisson,

et les panneaux émetteurs, nettoyez les

endroits où le gras, la graisse ou les aliments

ont pu s'accumuler. Brossez ou utilisez un

grattoir pour enlever toute accumulation de

débris sur les parois du panneau émetteur.

Veillez à ce que l'intérieur des boîtiers des

brûleurs soit débarrassé des débris. Retirez le

ramasse-miettes une fois refroidi et vidé. (Fig.

10)

Fig. 10

Grille de cuisson

Panneau émetteur

Ramasse-miettes

Protection anti-

chaleur

Intérieur du boîtier

de brûleur

Fig. 9

AVIS

- 9 -

FERMETURE COMPLÈTE DES BRULEURS

Pour fermer complètement : Tournez le robinet d'alimentation principal du gaz sur OFF

« FERMÉ ». Assurez-vous que les boutons individuels des brûleurs sont sur OFF

« FERMÉ » (tournés dans le sens des aiguilles d'une montre jusqu'à l'arrêt complet).

ALLUMAGE MANUEL DES BRÛLEURS

1. Tournez le robinet d'arrêt principal du gaz et

les boutons individuels de commande des

brûleurs en position OFF « FERMÉ » (dans

le sens des aiguilles d'une montre jusqu'à

l'arrêt). Attendez 5 minutes.

2. Appliquez une flamme à l'aide d'une source

d'allumage extérieure (comme par exemple

une fine bougie allumée, un allume-gaz à

long manche, etc.) directement dans

l'intervalle entre la base du panneau

émetteur et le dessus du boîtier du brûleur

choisi à l'avant de l'appareil. Voir Fig. 7.

3. Poussez et réglez le bouton de commande

du brûleur que vous voulez allumer en le

tournant sur MAX (dans le sens des aiguilles

d'une montre à la verticale/90°). (Fig.8)

4. Regardez par le trou de regard du brûleur

(Fig.8) pour vous assurer que le brûleur a

été allumé.

5. Si le brûleur ne s'allume pas dans les 4

secondes après l'application de la flamme à

l'endroit où elle a été dirigée, tournez le

robinet d'arrêt principal du gaz et tous les

boutons des brûleurs en position OFF

« FERMÉ » (dans le sens des aiguilles d'une

montre jusqu'à l'arrêt). Contactez le service

à la clientèle autorisé.

6. Répétez les étapes 2-4 jusqu'à ce que les

brûleurs soient allumés. Pour ouvrir tournez

un bouton de brûleur à la fois et vérifiez que

le brûleur est allumé avant de continuer à

allumer le brûleur suivant.

Trou de regard de brûleur

Bouton de commande des brûleurs

Fig. 8

Fig. 7

VUE DE COUPE

Source extérieure d'allumage

Panneau émetteur

Intervalle

Boîtier de brûleur

La page charge ...

Vulcan VTEC36 Le manuel du propriétaire

Ce manuel convient également à

Vulcan VTEC36 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents